Dualphone
Single Cordless
Ope
rating
M a n u al
D P45
The handset at a glance
The handset at a glance
16
©
£
1
2
INT 1
10.05.05
FixedLine
09:45
SMS
3
15
14
13
4
5
12
11
6
10
7
9
8
1 Display in idle status
2 Battery charge status
¡ ¢ £ ¤ (flat to full)
¡ flashes: battery nearly empty
¢ £ ¤ flashes: battery charging
3 Display keys (page 9)
4 Message key
Opens calls and message lists (depending
on the base station)
Flashes: new message or new call
5 End call key, On/Off key
End call, cancel function, go back one menu
level (press briefly), back to idle status
(press and hold), activate/deactivate
handset (press and hold in idle status)
6 Hash key
Key lock on/off (press and hold in idle
status)
Toggle between upper/lower case and digits
7 Call-by-call list key
Open call-by-call list
8 Connection socket for headset
9 Microphone
10 Recall key
‒ Confer (Flash)
‒ Insert a dialling pause (press and hold)
11 Star key
Ringtones on/off (press and hold)
Open table of special characters
12 Key 1
Select answering machine/network mailbox
(press and hold)
13 Talk key
Answer a call, open last number redial list
(press briefly), start dialling (press and hold)
14 Handsfree key
Switch between earpiece and handsfree
mode
Lights up: handsfree talking activated
Flashes: incoming call
15 Control key (page 8)
16 Signal strength
¨ § ¦ (high to low)
¥ flashes: no reception
Note:
Illustration of a handset on a base station with
SMS functionality.
1
Contents
Contents
The handset at a glance . . . . . . . . 1
Safety precautions . . . . . . . . . . . . 3
DP45 –
a handset with many extras . . . . . 4
First Steps . . . . . . . . . . . . . . . . . . . . 4
Pack contents . . . . . . . . . . . . . . . . . . . . . 4
Setting up the hanset for use . . . . . . . . . 4
Making calls . . . . . . . . . . . . . . . . . . 7
Making an external call . . . . . . . . . . . . . . 7
Ending a call . . . . . . . . . . . . . . . . . . . . . . 7
Answering a call . . . . . . . . . . . . . . . . . . . 7
Handsfree operation . . . . . . . . . . . . . . . . 7
Muting . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Making internal calls . . . . . . . . . . . . . . . . 8
Operating the handset . . . . . . . . . 8
Switching the handset on/off . . . . . . . . . 8
Activating/deactivating the
keypad lock . . . . . . . . . . . . . . . . . . . . . . . 8
Control key . . . . . . . . . . . . . . . . . . . . . . . 8
Display keys . . . . . . . . . . . . . . . . . . . . . . . 9
Reverting to idle status . . . . . . . . . . . . . . 9
Menu guidance . . . . . . . . . . . . . . . . . . . . 9
Correcting incorrect entries. . . . . . . . . . 10
Using the directory and lists . . . . 10
Directory and call-by-call list . . . . . . . . . 10
Last number redial list . . . . . . . . . . . . . . 12
Opening lists with the message key . . . 12
Using the handset as a room
monitor . . . . . . . . . . . . . . . . . . . . . 12
Activating the room monitor and
entering the number to be called . . . . . 13
2
Handset settings . . . . . . . . . . . . . 14
Changing the display language . . . . . . . 14
Setting the display . . . . . . . . . . . . . . . . . 14
Setting the screen picture . . . . . . . . . . . 14
Setting display illumination. . . . . . . . . . 14
Activating/deactivating auto
answer . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Adjusting the loudspeaker volume . . . . 15
Changing ringtones. . . . . . . . . . . . . . . . 15
Activating/deactivating advisory
tones . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Setting the alarm clock . . . . . . . . . . . . . 16
Restoring the handset default
settings . . . . . . . . . . . . . . . . . . . . . . . . . 17
Appendix . . . . . . . . . . . . . . . . . . . 17
Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Contact with liquid . . . . . . . . . . . . . . . . 17
Questions and answers . . . . . . . . . . . . . 18
Guarantee Certificate
United Kingdom . . . . . . . . . . . . . . . . . . 19
Guarantee Certificate
Ireland . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Notes on the operating
instructions . . . . . . . . . . . . . . . . . 21
Symbols used . . . . . . . . . . . . . . . . . . . . 21
Example: menu input . . . . . . . . . . . . . . 21
Example: multiple line input . . . . . . . . . 22
Wrting and editing a text message . . . . 22
Accessories. . . . . . . . . . . . . . . . . . 24
Index . . . . . . . . . . . . . . . . . . . . . . . 25
Safety precautions
Safety precautions
Caution:
Read the safety precautions and the user guide before use. Explain their contents to your children,
and the potential hazards associated with using the phone.
Use only the mains adapter supplied, as indicated on the underside of the charging cradle.
Only insert the recommended rechargeable batteries (page 19) i.e. Do not use any
other battery type or non-rechargeable batteries as this could result in significant health
risks and personal injury.
The operation of medical appliances may be affected. Be aware of the technical conditions
in your particular environment, (e.g. doctor’s surgery).
The handset may cause an unpleasant humming noise in hearing aids.
Do not install the charging cradle in bathrooms or shower rooms. Handset and charging
cradle are not splashproof (page 17).
Do not use your phone in environments with a potential explosion hazard
(e.g. auto paint shops).
If you give your DP45 to someone else, make sure you also give them the user guide.
All electrical and electronic products should be disposed of separately from the municipal
waste stream via designated collection facilities appointed by the government or the local
authorities.
This crossed-out wheeled bin symbol on the product means the product is covered by the
European Directive 2002/96/EC.
The correct disposal and separate collection of your old appliance will help prevent
potential negative consequences for the environment and human health. It is a
precondition for reuse and recycling of used electrical and electronic equipment.
For more detailed information about disposal of your old appliance, please contact your
local council refuse centre or the original supplier of the product.
Please note:
Not all of the functions described in this user guide are available in all countries.
3
DP45 – A handset with many extras
DP45 – a handset
with many extras
Your DP45 not only lets you store up to
150 telephone numbers (page 10) – your
DP45 can do much, much more:
u You can designate important people
as VIPs so you can tell important calls
from the “tone” (page 10).
u You can store anniversaries (page 11)
in your phone and it will remind you of
them in advance.
u Select frequently used phone numbers
at the press of a single key (page 11).
Have fun using your new DP45!
Inserting the batteries
Caution:
Only use the rechargeable batteries
recommended by Siemens (page 19)! This
means: Never use conventional batteries
(nonrechargeable) as this may cause
significant damage to health and property. For
example, the outer casing of the batteries
could be destroyed or the batteries could
explode. The phone could also malfunction or
be damaged as a result of using batteries that
are not of the recommended type.
¤ Fit the batteries with the correct
polarity (see diagram).
The polarity is indicated in/on the battery
compartment.
First Steps
Pack contents
u
u
u
u
u
u
u
one DP45 handset,
one charging cradle (incl. mains
adapter),
two batteries,
one battery cover,
one belt clip,
one user guide.
Setting up the handset for use
Connecting up the charging cradle and
mounting it on the wall (if required) is
described at the end of these instructions.
4
Closing the battery cover
¤ First align the battery cover with the
¤
notches on the lugs on the inside of the
housing.
Then press the cover closed so that it
clicks into place.
First steps
Attaching the belt clip
Registering your phone
There are notches for attaching the belt
clip on the side of the handset at the same
height as the display.
¤ Press the belt clip onto the back of the
handset so that the lugs on the belt clip
click into the notches.
Before you can use your DP45 you must
register it to a base station. It can be
registered to a maximum of four base
stations. The actual registration procedure will depend on the type of base
station.
Manual registration DP45
Opening the battery cover
¤ If fitted, remove the belt clip.
¤ Insert a fingernail into the headset
If the handset does not switch on
automatically when the batteries are
fitted, you must first charge the batteries.
You must activate manual registration of
the handset at both the handset and the
base station.
After it has registered, the handset returns
to idle status. The handset’s internal
number is shown in the display e.g. INT 1.
If not, repeat the procedure.
socket cavity and pull the battery cover
upwards.
5
First Steps
1. On the handset
v ¢Ð ¢Handset ¢Register H/Set
s
Select base station, e.g. Base
1, and press §OK§.
~
Enter the system PIN of the
base station (the default is
0000) and press §OK§. The
screen will display, e.g. Base 1.
2. On the base station
Notes:
– The handset should only be placed in a
base station or charging cradle that is
designed for it.
– When the handset is in the cradle, it
charges even if it is switched off.
– If the handset has switched itself off
because the batteries are flat and it is then
placed in the charging cradle, it will switch
itself on automatically.
– After the first battery charge and discharge
you may replace your handset in the
charging cradle after every call.
Within 60 secs. press and hold the
registration/ paging key on the base
station (page 1) (approx. 3 secs.).
Please remember:
Headset socket
u Always repeat the charging and dis-
You can connect the following types of
headset (with jack connector): HAMA
Plantronics M40, MX100 and MX150.
Charging batteries
¤ Plug the mains adapter of the charging
cradle into a mains power socket.
¤ Place the handset in the cradle with its
display facing forward.
To charge the batteries, leave the handset
in the charging cradle. If the handset is
activated, the flashing battery icon ¢ in
the top right of the display indicates that
the batteries are charging. During handset
operation, the battery icon indicates the
charge status of the batteries (page 1).
Initial charging and discharging of
batteries
The correct charge level can only be
displayed if the batteries are first fully
charged and discharged.
¤ To do this, leave the handset in the
charging cradle continuously for ten
hours. Your handset need not be
switched on for it to charge.
¤ Once the batteries are fully charged,
remove the handset from the charging
cradle and do not put it back again until
the batteries are fully discharged.
6
charging procedure if you remove the
batteries from the handset and reinsert
them.
u The batteries may become warm as
they are charging. This is not dangerous.
u After a time the charge capacity of the
batteries will decrease for technical
reasons.
Setting the date and time
If you have not yet set the date and time,
press the display key §Time§ to open the
input field.
To change the time, open the input field
via:
v ¢Ð ¢Date/Time
¤ Change multiple line input:
Date:
Enter day, month and year in 6-digit
format.
Time:
Enter hours and minutes with 4 digits,
e.g. 0 7 1 5 for 07:15 a.m.
§Save§
Press the display key.
Making calls
Changing the base station
If your handset is registered to more than
one base station, you can set it to a particular base station or to the base station
that has the best reception (Best Base).
v ¢Ð ¢Handset ¢Select Base
s
Select one of the registered
base stations or Best Base and
press §OK§.
Making calls
Making an external call
External calls are calls using the public
telephone network.
~c
Enter the number and press
the talk key.
Or:
c~
Press and hold the talk key c
and then enter the number.
You can cancel the dialling operation with
the end call key a.
You are shown the duration of the call
while the call is in progress.
Notes:
– Dialling using the directory, call-by-call list
(page 1, page 10) or last number redial list
(page 12) saves time re-entering numbers
and network provider access codes (“callby-call numbers”).
Ending a call
a
Press the end call key.
Answering a call
The handset indicates an incoming call in
three ways: by ringing, by a display on the
screen and by the flashing handsfree
key d.
You can accept the call by:
¤ Pressing the talk key c.
¤ Pressing the handsfree key d.
If the handset is in the charging cradle and
the Auto Answer function is activated
(page 15), the handset will take a call
automatically when you lift it out of the
cradle.
If the ringtone is intrusive, press the
display key §Silence§. You can take the call
so long as it is displayed on the screen.
Handsfree operation
In handsfree mode instead of holding the
handset to your ear you can put it down
e.g. on the table in front of you to allow
others to participate in the call.
Activating/deactivating handsfree
Activating while dialling
~d
¤
Enter the number and press
the handsfree key.
You should inform your caller before
you use the handsfree function so that
they know someone else is listening.
Switching between earpiece and
handsfree mode
d
Press the handsfree key.
During a call and when listening to the
answering machine (depending on the
base station), switch handsfree on or off.
If you wish to place the handset in the
charging cradle during a call:
¤ Press and hold the handsfree key d
while placing the handset in the base
station. If handsfree key d does not
light up, press the key again.
For how to adjust the volume, see
page 15.
7
Operating the handset
Muting
You can deactivate the microphone in
your handset during an external call. The
other party hears a wait melody.
u
Press the control key on the
left to mute the handset.
”
Press the display key to
reactivate the microphone.
Making internal calls
Internal calls to other handsets registered
on the same base station are free.
Activating/deactivating the
keypad lock
#
Press and hold the hash key.
You will hear the confirmation beep. The
icon ² appears in the display when the
keypad lock is activated.
The keypad lock is deactivated automatically if someone calls you. It is re-activated
when the call is finished.
Control key
Calling a specific handset
u
~
Or:
u
s
c
Initiate internal call.
Enter the number of the
handset.
Initiate internal call.
Select handset.
Press the talk key.
Calling all handsets (“group call”)
u
*
Initiate internal call.
Press the star key.
All handsets are called.
Ending a call
a
Press the end call key.
In the following information, the side of
the control key (top, bottom, right, left)
you have to press in each operating
situation is shown in black (e.g. v for
“press the right of the control key”).
The control key has a number of different
functions:
When the handset is in idle status
s
v
u
t
Open the directory.
Open main menu.
Open list of handsets.
Set the ringtones on the
handset (page 15).
Operating the handset
In the main menu and in input fields
Switching the handset on/off
You can use the control key to move the
cursor up t, down s, right v or left
u.
a
Press and hold the end call
key. You will hear the confirmation beep.
In lists and submenus
t/s
v
u
8
Scroll up/down line by line.
Open submenu or confirm
selection.
Go back one menu level, or
cancel.
Operating the handset
During an external call
s
u
t
Open the directory.
Initiate an internal consultation call.
Adjust loudspeaker volume for
earpiece and handsfree mode.
Display keys
The function of the display keys changes
depending on the particular operating
situation. Example:
FixedLine
SMS
1
2
1 Current display key functions are shown in
the bottom display line.
2 Display keys
Press the display key below to launch the
function.
The most important display symbols are:
§§§Menu§§§
Open the main menu.
§Options§
Open a context-dependent
menu.
—
Delete key: backspace deletes
one character at a time.
“
Go back one menu level or
cancel operation.
Ó
Copy number into directory.
Ÿ
On bases with built-in
answering machines: forward
external call to answering
machine.
•
Open the last number redial
list (depending on the base
station).
Returning to idle status
You can revert to idle status from anywhere in the menu as follows:
¤ Press and hold the end call key a.
Or:
¤ Do not press any key: after 2 minutes
the display will automatically revert to
idle status.
Changes that you have not confirmed or
saved by pressing §OK§, §Yes§, §Save§, §Send§ or
Save Entry §OK§ will be lost.
An example of the display in idle status is
shown on page 1.
Menu guidance
Your telephone’s functions are accessed
using a menu that has a number of levels.
Main menu (first menu level)
¤ Press v with the handset in idle
status to open the main menu.
The main menu functions are shown in
the display as a list with icon and name.
Accessing a function, i.e. opening the
corresponding submenu (next menu
level):
¤ Navigate to the function using the control key q. Press the display key §OK§.
Submenus
The functions in the submenus are
displayed as lists.
To access a function:
¤ Scroll to the function with the control
key q and press §OK§.
Or:
¤ Enter the corresponding digit
combination.
A short press on the end call key a
returns you to the previous menu level /
cancels the operation.
9
Using the directory and lists
Correcting incorrect entries
You can correct wrong characters in the
text by navigating to the wrong input
using the control key. You can then:
u press ˜ to delete the character to the
left of the cursor,
u insert characters to the left of the cursor,
u overwrite the character (flashing)
when entering the time and date etc.
u You will find examples of symbols
used, menu entries and multiple line
input in the appendix to this user
guide, page 21.
Using the directory and lists
You can store a maximum of 150 entries
in the directory and call-by-call list (the
actual number depends on the size of the
individual entries).
You create the directory and call-by-call
list for your own individual handset. You
can, however, send lists/entries to other
handsets or the base station (page 11).
Directory and call-by-call list
In the directory, you can store numbers
and the associated names.
¤ With the handset in idle status, open
the directory by pressing the s key.
The call-by-call list is used to store the
access codes for network providers
(so-called “call-by-call numbers”).
¤ Open the call-by-call list in idle status
by pressing the g key.
Length of entries
Number: max. 32 digits
Name:
max. 16 characters
Note:
For quick access to a number from the directory or the call-by-call list (quick dial), you can
assign the number to a key.
10
Storing a number in the directory
s ¢New Entry
¤ Change multiple line input:
Number:
Enter number.
Name:
Enter name.
Annivers.:
Enter anniversary if required
(page 11).
Shortcut:
Select key for quick dial.
¤ Save changes.
Storing a number in the call-by-call list
g ¢New Entry
¤ Change multiple line input:
Number:
Enter number.
Name:
Enter name.
Selecting entries in the directory and
call-by-call list
s/ g
Open directory or call-by-call
list.
You have the following options:
u Use s to scroll through the entries
until the required name is selected.
u Enter the first character of the name, or
scroll to the entry with s if required.
Dialling with the directory/call-by-call
list
s/ g ¢s(select entry)
c
Press the talk key.
The number is dialled.
Using the directory and lists
Managing entries in the directory/ callby-call lists
s/ g ¢s(select entry)
Viewing an entry
§View§
Press the display key.
The entry is displayed.
Back with §OK§.
Editing entries
§View§ §Edit§ Press display keys one after
the other.
¤ Carry out changes and save.
Using other functions
s/ g ¢s(select entry)
¢§Options§ (open menu)
The following functions can be selected
with q:
Display Number
Edit or add to a stored number. Then
dial or call up further functions by
pressing §Options§.
Edit Entry
Edit selected entry.
Delete Entry
Delete selected entry.
VIP Entry (directory only)
Mark a directory entry as VIP (Very
Important Person) and assign it a
particular ringtone. You can then
identify VIP calls by their ringtones.
Requirement: caller display (“CLIP”)
Copy Entry
Send a single entry to a handset
(page 11).
Delete List
Delete all entries in the directory/
call-by-call list.
Copy List (depending on the receiving
handset)
Send complete list to a handset
(page 11).
Available Memory
Display the available entries in the
directory and call-by-call list (page 10).
Using quick dial keys
¤ Press and hold the required quick dial
key.
Sending the directory/call-by-call list
to another handset
Requirements:
u The sending and receiving handsets
must both be registered to the same
base station.
u The other handset and base station
can send and receive directory entries.
Please read the relevant user guide for
further information.
s/ g ¢s(select entry)
¢§Options§ (open menu) ¢Copy Entry
/ Copy List
~
Enter the internal number of
the receiving handset. You see
Copying entry.
§Yes§ / §No§ Press the display key.
A successful transfer is confirmed by a
message and confirmation tone on the
receiving handset.
Please remember:
u Entries with identical numbers are not
overwritten on the receiving handset.
u The transfer is cancelled if the phone
rings or if the memory of the receiving
handset is full.
Storing anniversaries in the directory
You can store an anniversary for every
number in the directory, and specify a
time when you will receive a reminder call
on the anniversary.
s ¢s (Select entry; page 10)
§View§ §Edit§ Press display keys one after
the other.
s
Scroll to the Annivers.: line.
§Edit§
Press the display key.
¤ Change multiple line input:
11
Using a handset as a room monitor
Date:
Enter the day/month in 4-digit format.
Time:
Enter the hour/minute for the reminder
call in 4-digit format.
Prompt:
Select the type of signal for the
reminder and press §OK§
¤ Save changes (page 22).
Note:
Reminder calls require a time stamp. If you
select a visual signal, then a time stamp is not
required and is automatically set to 00.00.
Deleting anniversaries
s ¢s (Select entry; page 10)
§View§ §Edit§ Press display keys one after
the other.
s
Scroll to the Annivers.: line.
§Edit§ §Delete§ §Save§
Press display keys one after
the other.
Reminder call on an anniversary
A reminder call is signalled on the handset
using the selected ringtone.
§Silence§
Press the display key to stop
the reminder call.
Last number redial list
The last number redial list contains the
ten numbers last dialled with the handset
(max. 32 numbers). If one of the numbers
is in the directory, then the corresponding
name will be displayed.
Manual last number redial
c
s
c
Press the key briefly.
Select entry.
Press the talk key again.
The number is dialled.
When a name is displayed, you can display
the corresponding phone number by
pressing the display key §View§.
12
Managing entries in the last number
redial list
c
Press the key briefly.
s
Select entry.
§Options§
Open the menu.
The following functions can be selected
with q:
Display Number (as in the directory,
page 11)
Copy to Directory
Copy an entry to the directory
(page 10).
Delete Entry (as in the directory, page 11)
Delete List (as in the directory, page 11)
Opening lists with the message
key
An advisory tone sounds as soon as a new
entry appears on a list. The f key
flashes (it goes off when the key is
pressed). In idle status, the displays shows
an icon for the new message.
If you press the f key, you access the
lists which contain new messages.
Using a handset as a room
monitor
If the room monitor is activated, a
previously stored destination number is
called as soon as a set noise level is
reached. You can store an internal or
external number in your handset as the
destination number.
The room monitor call to an external
number stops after approx. 90 seconds.
The room monitor call to an internal
number (handset) stops after approx.
3 minutes (depending on the base station). While the room monitor is activated,
all keys are locked except the end call key.
The handset’s speaker is muted.
Menu tree
When the room monitor is activated,
incoming calls to the handset are indicated without a ringtone and are only
shown on the screen. The display and
keypad are not illuminated and advisory
tones are also turned off.
If you accept an incoming call, the room
monitor mode is suspended for the
duration of the call, but the function
remains activated.
If you switch off the handset, the room
monitor mode is deactivated. You must
reactivate the function after switching on
the handset again.
Caution!
– You should always check the operation of
the room monitor before use. For example,
test its sensitivity. Check the connection if
you are diverting the room monitor to an
outside number.
– When the function is switched on the
handset’s operating time is severely
reduced. If necessary, place the handset in
the charging cradle. This ensures that the
batteries do not run down.
– Ideally the handset should be positioned 1
to 2 metres away from the baby. The microphone must be directed towards the baby.
– The connection to which the room monitor
is diverted must not be blocked by an
activated answering machine.
Activating the room monitor and
entering the number to be called
v ¢í ¢Room Monitor
¤ Change multiple line input:
Room M.:
Select On to activate.
Call to:
Press the display key §Edit§ and enter
destination number.
External number: select number from
the directory or enter directly. Only the
last 4 digits are displayed.
Internal number: delete any stored
external number. §INT§ s (select hand-
set or Call All, if all registered handsets
are to be called) §OK§.
Save numbers with §Save§.
Level:
Set noise level sensitivity (Low or High).
¤ Save changes (page 22).
The function is now activated. With v,
you can move directly to settings.
Changing previously set external
destination number
v ¢í ¢Room Monitor
s
Scroll to the Call to: line.
§Edit§
Press the display key.
˜
Delete existing number.
¤ Enter number as described in “Activating the room monitor and entering the
number to be called” (page 13).
¤ Save changes (page 22).
Changing previously set internal
destination number
v ¢í ¢Room Monitor
s
Scroll to the Call to: line.
§Edit§
Press the display key.
§Yes§
Press the display key to
confirm the prompt.
¤ Enter number as described in “Activating the room monitor and entering the
number to be called” (page 13).
¤ Save changes (page 22).
Deactivating the room monitor
remotely
Requirements: The phone must support
touch tone dialling and the room monitor
is set for an external destination number.
¤ Take the call from the room monitor
and press keys 9 #.
The room monitor function will deactivate
after the call ends. There will be no further
room monitor calls. The other room monitor settings on the handset (e.g. no ring13
Handset settings
tone) will however remain activated until
you press the display key §Off§ on the
handset.
To reactivate the room function with the
same phone number:
¤ Turn on the activation again and save
with §Save§ (page 13).
Handset settings
Changing the display language
You can view the display texts in different
languages.
v ¢Ð ¢Handset ¢Language
The current language is indicated by .
s
Select a language and press
§OK§.
a
Press and hold (idle status).
If you accidentally choose a language you
do not understand:
v541
Press keys one after the other.
s
Select the correct language
and press §OK§.
Setting the display
You have a choice of four colour schemes
and several different contrasts.
v ¢Ð ¢Display
Colour Scheme
Select and press §OK§.
s
Select a colour scheme and
press §OK§
= current colour).
(
a
Press briefly.
Contrast
Select and press §OK§.
r
Select contrast.
§Save§
Press the display key.
a
Press and hold (idle status).
14
Setting the screen picture
You can display a screen picture (picture
or digital clock) when the handset is in
idle status. This will replace the idle status
display. It may conceal the date, time and
name.
The screen picture is not displayed in
certain situations, e.g. during a call or
when the handset has been deregistered.
If a screen picture has been activated, the
menu item Screen Picture is marked with
.
v ¢Ð ¢Display ¢Screen Picture
The current setting is displayed.
¤ Change multiple line input:
Activation:
Select On (screen picture is displayed)
or Off (no screen picture).
Selection:
Change screen picture if necessary (see
below).
¤ Save changes (page 22).
If the screen picture conceals the display,
press the end call key briefly to show the
idle display with time and date.
Changing the screen picture
v ¢Ð ¢Display ¢Screen Picture
s
Scroll to the Selection line.
View§
Press the display key.
The active screen picture is
displayed
s
Select Picture/Clock .
§Save§
Press the display key.
¤ Save changes.
Setting display illumination
Depending on whether or not the handset
is in the charging cradle you can set
different levels of display illumination. If
the charging cradle is switched on, the
display is permanently dimmed.
Handset settings
v ¢Ð ¢Display ¢Lighting
The current setting is displayed.
¤ Change multiple line input:
In Charger
Select On or Off.
Outside Charger
Select On or Off.
§Save§
Press the display key.
a
Press and hold (idle status).
Note:
When the display illumination is switched on,
the standby time of the handset is reduced to
approx. 30 hours.
Activating/deactivating auto
answer
If you have activated this function, when
you get a call you can simply lift the
handset out of the charging cradle
without having to press the talk key c.
v ¢Ð ¢Handset
Auto Answer
=on).
Select and press §OK§ (
a
Press and hold (idle status).
Adjusting the loudspeaker
volume
You can set the loudspeaker volume for
handsfree talking to five different levels
and the earpiece volume to three different
levels. You can only make these adjustments during a call.
The handsfree volume can only be
adjusted when this function is set.
You are conducting an external call.
t
Open menu.
r
Select volume.
§Save§
Press display key if necessary
to save the setting permanently.
If t is assigned a different function:
§Options§
Open menu.
Volume
Select and press §OK§.
Configure setting (see above).
Changing ringtones
u Volume:
You can choose between five volumes
(1–5; e.g. volume 2 = ˆ) and
the “Crescendo” ring (6; volume
increases with each ring =
‰).
u Ringtones:
You can choose between 15 different
melodies.
You can configure the following functions
with different ringtones:
u Ext. Calls: For external calls
u Internal Calls: For internal calls
u All: The same for all functions
Settings for individual functions
Set the volume and melody depending on
the type of signalling required.
v ¢Ð ¢Audio Settings ¢
Ringer Settings
q
Setting, e.g. select Ext. Calls
and press §OK§.
¤ Change multiple line input:
r
Set volume (1–6).
s
Scroll to the next line.
r
Select melody.
§Save§
Press the display key to save
the setting.
In idle status, you can also open the menu
Ringer Settings by pressing t briefly.
15
Handset settings
Settings for all functions to ring the
same
v ¢Ð ¢Audio Settings ¢
Ringer Settings ¢All
¤ Set volume and ringtone (see “Settings
for individual functions”).
§Yes§
Press the display key to
confirm the prompt.
a
Press and hold (idle status).
Activating/deactivating the ringtone
Before answering a call or while your
handset is in idle status, it is possible for
you to cancel the ringtone permanently or
for the current call. The ringtone cannot
be re-activated while an external call is in
progress.
Deactivating the ringtone permanently
*
Press the star key and hold
until you can no longer hear
the ringtone.
The µ icon appears in the display.
Re-activating the ringtone
*
Press and hold the star key.
Deactivating the ringtone for the current
call
§Silence§
Press the display key.
Activating/deactivating the alert tone
In place of the ringer tone you can
activate an alert tone. When you get a call,
you will hear a short tone (“Beep”)
instead of the ringtone.
*
Press and hold the star key
and within 3 seconds:
§Beep§
Press the display key. A call is
now signalled by one brief
alert tone. You will now see
º in the display.
16
Activating/deactivating advisory
tones
Your handset uses ‘advisory tones’ to tell
you about different activities and
statuses. The following advisory tones can
be activated and deactivated independently of each other:
u Key beep: Each key press is acknowledged.
u Acknowledge tones:
– Confirmation tone (rising tone
sequence): at the end of the entry/
setting and when an SMS or a new
entry arrives in the answering
machine list (depending on base) or
the calls list
– Error beep (descending tone
sequence): when you make an
incorrect entry
– Menu end tone: when scrolling at
the end of a menu
u Battery tone: the batteries need to be
charged.
v ¢Ð ¢Audio Settings ¢
Advisory Tones
¤ Change multiple line input:
Key Tones:
Select On or Off.
Confirm.:
Select On or Off.
Battery:
Select On, Off or In Call. The battery tone
is activated/deactivated or only sounds
during a call.
¤ Save changes (page 22).
You cannot deactivate the confirmation
tone for placing the handset in the
charging cradle.
Setting the alarm clock
Requirement: the date and time have
already been set (page 6).
Appendix
Activating/deactivating the alarm
clock and setting the wake-up time
v ¢ì
¤ Change multiple line input:
Activation:
Select On or Off.
Time:
Enter the wake-up time in 4-digit
format.
Melody:
Select melody.
Volume:
Set the volume (1-6).
¤ Save changes (page 22).
You will see the ¸ icon.
A wake-up call with the selected ringer
melody is signalled on the handset. The
wake-up call sounds for 60 seconds. The
display shows an Alarm Clock . If no key is
pressed the wake-up call is repeated twice
at five minute intervals and then switched
off.
During a call, the wake-up call is signalled
by a short tone.
Deactivating the wake-up call/
repeating after a pause (slumber
mode)
Requirement: A wake-up call is sounding.
§OFF§
Press the display key. The
wake-up call is deactivated.
or
§Snooze§
Press the display key or any
key. The wake-up call is
deactivated and then repeated
after 5 minutes. After the
second repetition the wake-up
call is deactivated completely.
affect entries in the directory, call-by-call
list or calls list, nor the handset’s registration to the base station.
v ¢Ð ¢Handset ¢Reset Handset
§Yes§
Press the display key.
Cancel the restoring process by pressing
a or the display key §No§.
a
Press and hold (idle status).
Appendix
Care
¤ Wipe the charging cradle and the
handset with a damp cloth (do not use
solvent) or an antistatic cloth.
Never use a dry cloth. This can cause
static.
Contact with liquid
If the handset has come into contact with
liquid:
1. Switch the handset off and remove
the batteries immediately.
2. Allow the liquid to drain from the
handset.
3. Pat all parts dry, then place the handset
with the battery compartment open
and the keypad facing down in a dry,
warm place for at least 72 hours (not
in a microwave, oven etc.).
4. Do not switch on the handset again
until it is completely dry.
When it has fully dried out, you will
normally be able to use it again.
Restoring the handset default
settings
You can reset any individual settings and
changes that you have made. This will not
17
Appendix
Questions and answers
Authorisation
The table below contains a list of common
problems and possible solutions.
This device is intended for use within the
European Union and Switzerland. If used
in other countries, it must first be
approved nationally in the country in
question.
Country-specific requirements have been
taken into consideration.
We, Siemens Home and Office Communication Devices GmbH & Co. KG, declare
that this device meets the essential
requirements and other relevant regulations laid down in Directive 1999/5/ EC.
The display is blank.
1. The handset is not switched on.
� Press and hold the end call key a.
2. The batteries are flat.
� Charge or replace the batteries (page 4).
The handset does not respond to a key press.
The keypad lock is activated.
� Press and hold the hash key # (page 8).
“Base station x” is flashing in the display.
1. The handset is outside the range of the
base station.
� Reduce the distance between handset/
base station.
2. The handset has been de-registered.
� Register the handset (page 5).
Base Search is flashing in the display.
Handset is set for Best Base and no base
station is within range.
� Reduce the distance between handset/
base station.
Handset does not ring.
The ringtone is switched off.
� Activate the ringtone (page 16).
The other party cannot hear you.
You have pressed the u (INT) key.
The handset is “muted”.
� Switch on the microphone again (page 8).
You hear an error tone when keying an input
(a descending sequence of tones).
Action has failed/invalid input.
� Repeat the operation.
Watch the display and refer to the
operating instructions if necessary.
18
0682
Appendix
Guarantee Certificate
United Kingdom
Without prejudice to any claim the user
(customer) may have in relation to the
dealer or retailer, the customer shall be
granted a manufacturer’s Guarantee
under the conditions set out below:
u In the case of new devices and their
components exhibiting defects resulting from manufacturing and/or material faults within 24 months of purchase, Siemens shall, at its own option
and free of charge, either replace the
device with another device reflecting
the current state of the art, or repair
the said device. In respect of parts
subject to wear and tear (including but
not limited to, batteries, keypads, casing), this warranty shall be valid for six
months from the date of purchase.
u This Guarantee shall be invalid if
the device defect is attributable to
improper treatment and/or failure to
comply with information contained in
the user guides.
u This Guarantee shall not apply to or
extend to services performed by the
authorised dealer or the customer
themselves (e. g. installation, configuration, software downloads). User
guides and any software supplied
on a separate data medium shall be
excluded from the Guarantee.
u The purchase receipt, together with
the date of purchase, shall be required
as evidence for invoking the Guarantee. Claims under the Guarantee must
be submitted within two months of the
Guarantee default becoming evident.
u Ownership of devices or components
replaced by and returned to Siemens
shall vest in Siemens.
u This Guarantee shall apply to new
devices purchased in the European
Union. For Products sold in the United
Kingdom the Guarantee is issued by:
Siemens Home and Office Communica-
tion Devices GmbH & Co. KG, Schlavenhorst 66, D-46395 Bocholt, Germany.
u Any other claims resulting out of or in
connection with the device shall be
excluded from this Guarantee. Nothing in this Guarantee shall attempt to
limit or exclude a Customer’s Statutory
Rights, nor the manufacturer’s liability
for death or personal injury resulting
from its negligence.
u The duration of the Guarantee shall
not be extended by services rendered
under the terms of the Guarantee.
u Insofar as no Guarantee default exists,
Siemens reserves the right to charge
the customer for replacement or repair.
u The above provisions do not imply a
change in the burden of proof to the
detriment of the customer.
To invoke this Guarantee, please contact
the Siemens telephone service. The
relevant number is to be found in the
accompanying user guide.
Guarantee Certificate
Ireland
Without prejudice to any claim the user
(customer) may have in relation to the
dealer or retailer, the customer shall be
granted a manufacturer’s Guarantee
under the conditions set out below:
u In the case of new devices and their
components exhibiting defects resulting from manufacturing and/or material faults within 24 months of purchase, Siemens shall, at its own option
and free of charge, either replace the
device with another device reflecting
the current state of the art, or repair
the said device. In respect of parts
subject to wear and tear (including but
not limited to, batteries, keypads, casing), this warranty shall be valid for six
months from the date of purchase.
19
Appendix
u This Guarantee shall be invalid if the
u
u
u
u
u
u
u
u
u
u
20
device defect is attributable to improper care or use and/or failure to comply
with information contained in the user
manuals. In particular claims under the
Guarantee cannot be made if:
The device is opened (this is classed as
third party intervention)
Repairs or other work done by persons
not authorised by Siemens.
Components on the printed circuit
board are manipulated
The software is manipulated
Defects or damage caused by dropping, breaking, lightning or ingress of
moisture. This also applies if defects
or damage was caused by mechanical,
chemical, radio interference or thermal
factors (e.g.: microwave, sauna etc.)
Devices fitted with accessories notauthorised by Siemens
This Guarantee shall not apply to or
extend to services performed by the
authorised dealer or the customer
themselves (e.g. installation, configuration, software downloads). User
manuals and any software supplied
on a separate data medium shall be
excluded from the Guarantee.
The purchase receipt, together with
the date of purchase, shall be required
as evidence for invoking the Guarantee. Claims under the Guarantee must
be submitted within two months of the
Guarantee default becoming evident.
Ownership of devices or components
replaced by and returned to Siemens
shall vest in Siemens.
This Guarantee shall apply to new
devices purchased in the European Union. For Products sold in the Republic
of Ireland the Guarantee is issued by
Siemens Home and Office Communication Devices GmbH & Co. KG, Schlavenhorst 66, D-46395 Bocholt, Germany.
u Any other claims resulting out of or in
connection with the device shall be
excluded from this Guarantee. Nothing in this Guarantee shall attempt to
limit or exclude a Customer’s Statutory
Rights, nor the manufacturer’s liability
for death or personal injury resulting
from its negligence.
u The duration of the Guarantee shall
not be extended by services rendered
under the terms of the Guarantee.
u Insofar as no Guarantee default exists,
Siemens reserves the right to charge
the customer for replacement or repair.
u The above provisions does not imply
a change in the burden of proof to the
detriment of the customer.
To invoke this Guarantee, please contact
the Siemens helpdesk on 1850 777 277.
This number is also to be found in the
accompanying user guide.
Notes on the opperating instructtions
Notes on the operating
instructions
This section explains the meaning of
certain symbols and typographical
conventions that are used in this user
guide.
Symbols used
Copy Entry / Copy List (example)
Select one of the two menu
functions specified.
~
Enter digits or letters.
§Save§
The display keys’ current
functions are shown reverse
highlighted in the bottom
display line.
q
Press the top or the bottom of
the control key: scroll up or
down.
r
Press the right or left of the
control key: e.g. select setting.
c/ 0/ * etc.
Press the corresponding key
on the handset.
Example: menu input
In the user guides, the steps you need to
perform are shown in abbreviated form.
This is illustrated below using the example
of “Contrast”. The things you have to do
are explained in the boxes.
v ¢Ð ¢Display
¤ With the handset in idle status, press
on the right of the control key to open
the main menu.
¤ Select the Ð icon using the control key
‒ press the control key at the top or
bottom.
In the display header, Settings is
displayed.
¤ Press the display key §OK§ to confirm
the function Settings.
The Settings submenu is displayed.
¤ Press the bottom of the control key
repeatedly until Display is selected.
¤ Press the display key §OK§ to confirm
the selection.
Contrast
Select and press §OK§.
¤ Press the bottom of the control key
repeatedly until Contrast is selected.
¤ Press the display key §OK§ to confirm
the selection.
r
Select contrast and press §OK§.
¤ Press right or left on the control key to
select the contrast.
¤ Press the display key §Save§ to confirm
the selection.
a
Press and hold (idle status).
¤ Press and hold the end call key until
the hanset returns to idle status.
21
Notes on the opperating instructtions
Example: multiple line input
There are many situations in which you
can change the settings of a display or
enter data in several lines.
In this user guide symbols are used to
guide you step-by-step through multiple
line input. This is illustrated below using
the example of “Setting the date and
time”. The things you have to do are
explained in the boxes.
You will see the following display
(example):
Date/Time
Date:
[10.06.05]
Time:
11:11
Ý
The following rules apply when writing a
text message:
u Control the cursor with u v t
s.
u Characters are added to the left of the
cursor.
u Press the star key * to show the
table of special characters.
u The first letter of the name of directory
entries is automatically capitalised, followed by lower case letters.
Entering special characters
SAVE
Date:
Enter day, month and year in 6-digit
format.
The second line is marked with [ ] to
show it is active.
¤ Enter the date using the digit keys.
Time:
Enter hours/minutes in 4-digit format.
¤ Press the s key
The fourth line is marked with [ ] to
show it is active.
¤ Enter the date using the digit keys.
¤ Save Changes.
¤ Press the display key §Save§.
¤ The press and hold the a key.
The handset changes to idle status.
22
Writing and editing a text
message
You can call up the table of special characters when writing an SMS using the *
key. Select the required character and
insert it with §Insert§.
Writing an SMS/name
(without predictive text)
Requirement:
Your base station must support SMS.
Press and hold the hash key # to switch
from “Abc” mode to “123” and from “123”
to “abc” and from “abc” to “Abc” (upper
case: 1st letter upper case, all others
lower case). Press the hash key #
before entering the letter.
The following applies when writing an
SMS:
u The display shows whether upper case,
lower case or digits is selected. “Abc”,
“abc” or “123” appears at the top right
of the display.
u When you press a key and hold it, the
characters of that key appear in the
bottom display line and are highlighted one after the other. When you
release the key the highlighted character is inserted into the input field.
Notes on the opperating instructtions
Writing SMS (with predictive text)
Order of directory entries
Requirement:
Your base station must support SMS.
EATONI predictive text helps you when
you are writing text messages.
Each key between 0 and 9 is
assigned several letters and characters.
These appear in a selection line immediately under the text panel (above the
display keys) as soon as you press a key.
The letter you are most likely looking for is
shown in reversed highlights and is at the
beginning of the selection line. It is copied
into the text panel.
1
612(1)
Ç
Abc
2
The directory entries are usually sorted in
alphabetical order. Spaces and digits take
first priority. The sort order is as follows:
1. Space
2. Digits (0–9)
3. Letters (alphabetical)
4. Other characters
To get round the alphabetical order of the
entries, insert a space or a digit in front of
the name. These entries will then move to
the beginning of the directory. Names
which you have preceded with an asterisk
will move to the end of the directory.
Hello Peter, I cannot come
today. lc
3
4
hgi
Û
1
2
3
4
Options
EATONI is activated
Upper/lower case or digits
SMS text
Selection line
If this letter is the one you want, confirm it
by pressing the next key. If it is not the one
you want, briefly press the hash key #
repeatedly until the required letter is
reverse-highlighted on the display line
and copied into the text panel.
If you press and hold the hash key #
you switch from “Abc” mode to “123” and
from “123” to “abc” and from “abc” to
“Abc”.
Deactivating/activating predictive text
Requirement: You are writing a text
message.
§Options
Press the display key.
Predictive Text
=on).
Select and press §OK§ (
a
Press the end call key briefly to
return to the text panel.
Enter the text.
23
Accessories
Accessories
All accessories and batteries are available from your mobile phone retailer.
Only use original accessories. This will avoid possible health risks and damage,
and also ensure that all the relevant regulations are complied with.
24
Index
Index
A
Accessories . . . . . . . . . . . . . . . . . . . . . . 24
Acknowledge tones . . . . . . . . . . . . . . . . 16
Activating
advisory tones . . . . . . . . . . . . . . . . . 16
call acceptance . . . . . . . . . . . . . . . . . 15
handset . . . . . . . . . . . . . . . . . . . . . . . . 8
keypad lock . . . . . . . . . . . . . . . . . . . . . 8
room monitor . . . . . . . . . . . . . . . . . . 13
Adjusting
loud speaker volume . . . . . . . . . . . . 15
Advisory tones . . . . . . . . . . . . . . . . . . . . 16
Alarm clock
setting . . . . . . . . . . . . . . . . . . . . . . . . 16
Alert tone . . . . . . . . . . . . . . . . . . . . . . . 16
Anniversary . . . . . . . . . . . . . . . . . . . . . . 11
Answering a call . . . . . . . . . . . . . . . . . . . 7
Auto answer . . . . . . . . . . . . . . . . . . . 7, 15
B
Base station
changing . . . . . . . . . . . . . . . . . . . . . . . 7
Battery
charging . . . . . . . . . . . . . . . . . . . . . . . 1
display. . . . . . . . . . . . . . . . . . . . . . . . . 1
fitting . . . . . . . . . . . . . . . . . . . . . . . . . 4
icon . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
recommended batteries . . . . . . . . . . 19
symbol . . . . . . . . . . . . . . . . . . . . . . . . 1
Battery icon . . . . . . . . . . . . . . . . . . . . . . . 6
Battery pack
charging . . . . . . . . . . . . . . . . . . . . . . . 6
Battery tone . . . . . . . . . . . . . . . . . . . . . . 16
Best base station . . . . . . . . . . . . . . . . . . . 7
C
Call
ending . . . . . . . . . . . . . . . . . . . . . . . . 7
external. . . . . . . . . . . . . . . . . . . . . . . . 7
internal . . . . . . . . . . . . . . . . . . . . . . . . 8
Call acceptance . . . . . . . . . . . . . . . . . . . 15
Call duration . . . . . . . . . . . . . . . . . . . . . . 7
Call-by-call list . . . . . . . . . . . . . . . . . . . . 10
key . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Call-by-Call numbers . . . . . . . . . . . . . . . 10
Calls list . . . . . . . . . . . . . . . . . . . . . . . . . 12
Cancelling (operation) . . . . . . . . . . . . . . 9
Care, phone . . . . . . . . . . . . . . . . . . . . . . 17
Changing
destination number . . . . . . . . . . . . . 13
display language . . . . . . . . . . . . . . . . 14
ringtone . . . . . . . . . . . . . . . . . . . . .15
Character set, see Special characters . . 22
Charge status display . . . . . . . . . . . . . 1, 6
Confirmation beep . . . . . . . . . . . . . . . . 16
Control key . . . . . . . . . . . . . . . . . . . . . 1, 8
Correcting incorrect input . . . . . . . . . . . 10
Customer service . . . . . . . . . . . . . . . . . . 18
D
Deactivating
handset . . . . . . . . . . . . . . . . . . . . . . . . 8
keypad lock . . . . . . . . . . . . . . . . . . . . . 8
Default settings
handset . . . . . . . . . . . . . . . . . . . . . . . 17
Delete key . . . . . . . . . . . . . . . . . . . . . . . . 9
Deleting
characters . . . . . . . . . . . . . . . . . . . . . 10
Dialling pause
entering . . . . . . . . . . . . . . . . . . . . . . . 1
Digital clock . . . . . . . . . . . . . . . . . . . . . . 14
Directory . . . . . . . . . . . . . . . . . . . . . . . . 10
managing entries . . . . . . . . . . . . . . . 11
opening . . . . . . . . . . . . . . . . . . . . . 8, 9
order of entries . . . . . . . . . . . . . . . . . 23
saving anniversary . . . . . . . . . . . . . . 11
saving entry . . . . . . . . . . . . . . . . . . . 10
sending entry/list to handset . . . . . . 11
Display
changing display language . . . . . . . . 14
colour skin/contrast . . . . . . . . . . . . . 14
display keys . . . . . . . . . . . . . . . . . . . 1, 9
illumination . . . . . . . . . . . . . . . . . . . 14
in idle status . . . . . . . . . . . . . . . . . . . . 9
memory . . . . . . . . . . . . . . . . . . . . . . 11
screen picture . . . . . . . . . . . . . . . . . . 14
setting . . . . . . . . . . . . . . . . . . . . . . . . 14
wrong language . . . . . . . . . . . . . . . . 14
E
Earpiece mode. . . . . . . . . . . . . . . . . . . . . 7
Earpiece volume . . . . . . . . . . . . . . . . . . 15
EATONI (predictive text) . . . . . . . . . . . . 23
End call key . . . . . . . . . . . . . . . . . . . . . 1, 7
Ending a call . . . . . . . . . . . . . . . . . . . . . . 7
Entering special characters . . . . . . . . . . 22
Error beep . . . . . . . . . . . . . . . . . . . . . . . 16
25
Index
Example
menu input . . . . . . . . . . . . . . . . . . . . 21
multiple line entry . . . . . . . . . . . . . . 22
F
Fast access
assigning key 1 . . . . . . . . . . . . . . . . . . 1
G
Group call . . . . . . . . . . . . . . . . . . . . . . . . 8
Guarantee Certificate . . . . . . . . . . . . . . 19
H
Handset
activating/deactivating . . . . . . . . . . . . 8
advisory tones . . . . . . . . . . . . . . . . . 16
changing to best reception . . . . . . . . . 7
changing to different base station . . . 7
contact with liquid . . . . . . . . . . . . . . 17
display illumination . . . . . . . . . . . . . 14
display language . . . . . . . . . . . . . . . . 14
idle status . . . . . . . . . . . . . . . . . . . . . . 9
list . . . . . . . . . . . . . . . . . . . . . . . . . . 8, 9
loudspeaker volume . . . . . . . . . . . . . 15
muting . . . . . . . . . . . . . . . . . . . . . . . . 8
operating and charging times . . . . . 19
registering . . . . . . . . . . . . . . . . . . . . . 5
registering on another base station . . 7
restoring default settings . . . . . . . . . 17
screen picture . . . . . . . . . . . . . . . . . . 14
using room monitor . . . . . . . . . . . . . 12
Handset charging times . . . . . . . . . . . . 19
Handset operating time . . . . . . . . . . . . 19
in room monitor mode . . . . . . . . . . . . . 13
Handsfree
key . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Handsfree talking . . . . . . . . . . . . . . . . . . 7
Hash key . . . . . . . . . . . . . . . . . . . . . . . 1, 8
Headset socket . . . . . . . . . . . . . . . . . . . . 6
Hearing aids . . . . . . . . . . . . . . . . . . . . . . 3
I
Icon
alarm clock . . . . . . . . . . . . . . . . . . . . 17
ringtone . . . . . . . . . . . . . . . . . . . . . . 16
Idle status (display) . . . . . . . . . . . . . . . . . 9
Idle status, returning to . . . . . . . . . . . . . . 9
Incorrect input (correction) . . . . . . . . . . 10
Internal call . . . . . . . . . . . . . . . . . . . . . . . 8
26
K
Key 1 (fast access) . . . . . . . . . . . . . . . . . . 1
Key click . . . . . . . . . . . . . . . . . . . . . . . . . 16
Keypad lock . . . . . . . . . . . . . . . . . . . . . . . 8
Keys
assigning directory entry . . . . . . . . . 10
call-by-call key . . . . . . . . . . . . . . . . . . 1
cancel key . . . . . . . . . . . . . . . . . . . . . . 9
control key . . . . . . . . . . . . . . . . . . . 1, 8
delete key . . . . . . . . . . . . . . . . . . . . . . 9
display keys . . . . . . . . . . . . . . . . . . . 1, 9
end call key . . . . . . . . . . . . . . . . . . . 1, 7
fast access . . . . . . . . . . . . . . . . . . . . . . 1
handsfree key . . . . . . . . . . . . . . . . . . . 1
hash key . . . . . . . . . . . . . . . . . . . . . 1, 8
menu key . . . . . . . . . . . . . . . . . . . . . . 9
message key . . . . . . . . . . . . . . . . . . . . 1
On/Off key. . . . . . . . . . . . . . . . . . . . . . 1
quick dial. . . . . . . . . . . . . . . . . . . . . . 10
recall key . . . . . . . . . . . . . . . . . . . . . . . 1
star key . . . . . . . . . . . . . . . . . . . . . 1, 16
talk key . . . . . . . . . . . . . . . . . . . . . . 1, 7
L
Language, display . . . . . . . . . . . . . . . . . 14
Last number redial list . . . . . . . . . . . . . . 12
Last number redial, manual . . . . . . . . . 12
Liquid. . . . . . . . . . . . . . . . . . . . . . . . . . . 17
List
call-by-call list . . . . . . . . . . . . . . . . . . 10
handsets . . . . . . . . . . . . . . . . . . . . . 8, 9
last number redial list . . . . . . . . . . . . 12
Lock
activating/deactivating keypad lock . . 8
Loudspeaker volume . . . . . . . . . . . . . . . 15
M
Mains adapter . . . . . . . . . . . . . . . . . . . . . 3
Making calls
answering a call . . . . . . . . . . . . . . . . . 7
external. . . . . . . . . . . . . . . . . . . . . . . . 7
internal . . . . . . . . . . . . . . . . . . . . . . . . 8
Manual last number redial . . . . . . . . . . 12
Medical appliances . . . . . . . . . . . . . . . . . 3
Memory
directory . . . . . . . . . . . . . . . . . . . . . . 11
Menu
back one menu level . . . . . . . . . . . . . . . . 9
end tone . . . . . . . . . . . . . . . . . . . . . . . . 16
key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
open . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Index
Menu input . . . . . . . . . . . . . . . . . . . . . . 21
Message key . . . . . . . . . . . . . . . . . . . . . . 1
opening lists . . . . . . . . . . . . . . . . . . . 12
Microphone . . . . . . . . . . . . . . . . . . . . . . . 1
Multiple line entry . . . . . . . . . . . . . . . . . 22
Muting . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
On/Off key . . . . . . . . . . . . . . . . . . . . . . . . 1
Open
menu . . . . . . . . . . . . . . . . . . . . . . . . . 8
Opening
directory . . . . . . . . . . . . . . . . . . . . . 8, 9
Order of entries in directory . . . . . . . . . 23
Setting
alarm clock . . . . . . . . . . . . . . . . . . . . 16
date . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
display illumination . . . . . . . . . . . . . 14
display language . . . . . . . . . . . . . . . . 14
loud speaker volume . . . . . . . . . . . . 15
ringtone volume . . . . . . . . . . . . . . . . 15
screen picture . . . . . . . . . . . . . . . . . . 14
time . . . . . . . . . . . . . . . . . . . . . . . . . . 6
volume, melody . . . . . . . . . . . . . . . . 15
Setting melody . . . . . . . . . . . . . . . . . . . 15
Setting the date . . . . . . . . . . . . . . . . . . . . 6
Setting the time . . . . . . . . . . . . . . . . . . . . 6
Settings, see Setting
Signal beep, see Advisory tones
Slumber mode . . . . . . . . . . . . . . . . . . . . 17
Sound
ringtone . . . . . . . . . . . . . . . . . . . . . . 15
Specifications . . . . . . . . . . . . . . . . . . . . 19
Star key . . . . . . . . . . . . . . . . . . . . . . . 1, 16
P
T
Pack contents . . . . . . . . . . . . . . . . . . . . . 4
Phoning
internal . . . . . . . . . . . . . . . . . . . . . . . . 8
Predictive text . . . . . . . . . . . . . . . . . . 23
Talk key . . . . . . . . . . . . . . . . . . . . . . . . 1, 7
Text
writing, editing . . . . . . . . . . . . . . . . . 22
Troubleshooting . . . . . . . . . . . . . . . . . . 17
Q
V
Quick dial . . . . . . . . . . . . . . . . . . . . . 10, 11
VIP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Volume
earpiece . . . . . . . . . . . . . . . . . . . . . . 15
handset loudspeaker . . . . . . . . . . . . 15
loudspeaker . . . . . . . . . . . . . . . . . . . 15
ringtone . . . . . . . . . . . . . . . . . . . . . . 15
setting . . . . . . . . . . . . . . . . . . . . . . . . 15
N
Network provider (number list) . . . . . . . 10
Number
as destination for room monitor . . . 13
saving in directory . . . . . . . . . . . . . . 10
Number list (network provider) . . . . . . . 10
O
R
Recall key . . . . . . . . . . . . . . . . . . . . . . . . . 1
Registering (handset) . . . . . . . . . . . . . . . 5
Reminder call . . . . . . . . . . . . . . . . . . . . . 12
Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Ringtone
changing . . . . . . . . . . . . . . . . . . . . . . 15
setting melody . . . . . . . . . . . . . . . . . 15
setting volume . . . . . . . . . . . . . . . . . 15
Room monitor. . . . . . . . . . . . . . . . . . 12
activating . . . . . . . . . . . . . . . . . . . . . 13
entering destination number . . . . . . 13
sensitivity . . . . . . . . . . . . . . . . . . . . . 13
W
Wait melody . . . . . . . . . . . . . . . . . . . . . . 8
Warning beep, see Advisory tones
Writing . . . . . . . . . . . . . . . . . . . . . . . . . . 22
S
Safety precautions . . . . . . . . . . . . . . . . . . 3
Screen picture . . . . . . . . . . . . . . . . . . . . 14
Searching in directory . . . . . . . . . . . . . . 10
Sending
directory entry to handset . . . . . . . . 11
27
Notes
28
Issued by
Siemens Home and Office Communication Devices GmbH & Co. KG
Schlavenhorst 66
D-46395 Bocholt
© Siemens Home and Office Communication Devices GmbH & Co. KG 2005
All rights reserved. Subject to availability.
Rights of modification reserved.
www.siemens.com
www.tesco.com