Epson ActionPrinter 3250 Specifications
Add to my manuals9 Pages
Epson ActionPrinter 3250
The Epson ActionPrinter 3250 is a versatile and powerful printer that offers a wide range of features to meet your printing needs.
With its fast printing speed of up to 200 characters per second in draft mode, the ActionPrinter 3250 can quickly and efficiently handle large print jobs. Whether you are printing text documents, graphics, or presentations, the ActionPrinter 3250 delivers crisp, high-quality results.
The printer also offers a variety of paper handling options. It can accept single sheets, continuous paper, or envelopes, making it suitable for a wide range of printing tasks. The ActionPrinter 3250 also features a built-in paper cassette that can hold up to 50 sheets of paper.
advertisement
narrow cover
/
parallel interface printer cover
Y Power switch r-thickness lever
ActionPrinter 3250
Printing speed:
Quality
Draft
Printing direction:
Line spacing:
Paper feed speed:
Input buffer
Printable columns:
L Q
Characters/inch
10
12
10
12
Characters/second/line
167
200
60
72
Bidirectional logic-seeking for text and graphics.
(Unidirectional for graphics can be selected with the default-setting mode or the proper software command.)
1/6 inch, 1/8 inch, or programmable in 1/360-inch increments.
91 ms per 1/6-inch line; 2.22 inches/second with continuous feed
11KB when download default setting OFF
1.75KB when download default setting ON
Character sizes
10 cpi
10 cpi condensed
12 cpi
12 cpi condensed
15 cpi
Maximum printed characters
80
137
96
160
120
FONT lights
I I
FONT/YES FORM FEED/NO button button
I
Control panel
You can also select other font/pitch combinations using ESC/P2 commands.
CD cable dip power cord
Note: In some locations, the power cord may be attached to the printer.
I
Printer Specifications
Printing
Printing method: 24-pin impact dot matrix
One italic and 15 graphics character tables for
European version
One italic and 5 graphics character tables for non-
European version
14 international character sets and one legal character set
Character sets:
Paper
Thickness
Weight
Input paper supply
US model: Letter (8.5 x 11 inches)
Other models:
A4 (210 x 297 mm)
0.065 to 0.14 mm (0.0026 to 0.0055 inches)
64 to 90 g/m
2
(17 to 24 lb) l
Use 90 g/m
2
(24 lb) paper under normal conditions.
50 sheets for 82 g/m
2
(22 lb)
60 sheets for 64 g/m
2
(17 lb)
Total thickness of paper stack should be less then
5 mm (0.2 inches).
24-Pin Printers 3/17/92 AP-3250-1
ActionPrinter 3250
Single sheets (Manual insertion):
Width 148 to 257 mm (5.8 to 10.1 inches)
Thickness weight
92 lo 364 mm (3.6 to 14.3 inches)
0.065 to 0.14 mm (0.0026 to 0.0055 inches)
52 to 90 g/m
2
(14 to 24 lb)
Continuous paper:
Width
Copies
Thickness
Weight
101 to 254 mm (4 to 10 inches)
Two sheets (one original plus one copy)
0.065 to 0.18 mm (0.0026 to 0.007l inches) total
52 to 82g/m
2
(14 to 22 lb) for one sheet
40 to 58g/m
2
(12 to 15 lb) per sheet in multi-part forms l
Use only two-part carbonless multi-part forms and use them only with the optional push tractor.
Note: You can use recycled paper under normal conditions. If you notice increases in ribbon consumption and paper jamming, use a higher grade of paper.
Labels:
Size
Thickness
Weight
101 to 254 mm (4 to 10 inches) width for backing sheet
63.5 x 23.8 mm (2 1/2 x 1 5/16 inches) minimum for a label
0.07 to 0.09 mm (0.0028 to 0.0035 inches) for backing sheet
0.16 to 0.19 mm (0.0063 to 0.0075 inches) total
68 g/m
2
(17 lb) l Use continuous type labels only with the optional l push tractor.
Use labels onIy under normal temperature and humidity conditions.
Envelopes:
Size No.6
No. 10
Thickness
166 x 92 mm (6.5 x 3.6 inches)
240 x 104
mm (9.4 x 4.1 inches)
0.16 to 0.48 mm (0.0063 to 0.0197 inches)
45 to 75g/m
2
(12 to 20 lb) l l
Use envelopes only under normaI temperature and humidity conditions.
Load enveIopes with the longer side inserted into the rear slot by manual insertion only.
Printable area:
Single sheets (paper cassette and manual insertion) and envelopes
A printable area
A The minimum lop margin is 8.5 mm (0.33 inches).
B The minimum left margin is
3 mm
(0.12 inches).
The minimum right margin is:
3.8 mm
(0.15 inches) for the A4-size paper cassette
9.7 mm (0.38 inches) for the letter-size paper cassette
3 mm (0.12 inches) for manual insertion
However, the maximum printable width is 203 mm (8 inches).
C The minimum bottom margin is
13.5 mm (0.53 inches).
Continuous paper
A
The minimum top and bottom margins above and below the perforation are
9 mm (0.35 inches).
B The minimum left and right margins am 13 mm (0.51 inches).
The maximum printable width is 203 mm (6 inches).
Mechanical
Paper-feed methods:
MTBF:
Print head life:
Dimensions and weight:
Friction (paper cassette and manual insertion)
Push tractor (optional)
Black ribbon cartridge S015032
Life expectancy : 2 million character at
48 dots/character
4000 power-on hours (10% duty)
100 million strokes/wire
Height 130 mm (5.1 inches)
Width 375 mm (14.8 inches)
Depth 252 mm (9.9 inches)
Weight 4.5 kg (10 lb)
Electrical
120 V model:
Bated voltage:
Input voltage range
Rated frequency range:
Rated current:
Power consumption:
Dielectric strength:
220-230 V model:
Rated voltage:
Input voltage range:
Rated frequency range:
W~Wvw
Power consumption:
Dielectric strength:
AC l20 V
AC 103.5 to 132 V
50 to 60Hz
49.5 to 60.5 Hz
1.1 A
30 W (during self-test printing in draft mode at
10 cpi)
AC 1 kV rms, 1 second (betwem AC line and chassis)
AC220-230V
AC 198 to 244 V
50 to 60 Hz
49.5 to 60.5
Hz
0.6 A
30 W (during self-test printing in draft
mode at
10 cpi)
AC 1.5 kV rms, 1 second (between AC line and
240 v model:
Rated voltage:
Input voltage range:
Rated frequency range:
Input frequency range:
Rated current:
Power consumption:
Dielectric strength:
AC 240V
AC 216 to 264V
50 to 60 Hz
49.5 to 60.5 Hz
0.6 A
30 W (during self-test printing in draft mode at
AP-3250-2 3/17/92 24-Pin Printers
Environmental
Temperature Operation:
Storage:
Humidity (without condensation):
Operation: storage:
5 to 35°C (41 to 95°F)
-20 to 55°C (4 to 131°F)
30 to 80% RH
5 to 85% RH
Safety approvals
Safety Standards:
US
model:
UL1950 with D3, CSA22.2 #220
European model: EN 60950 (TUV), IEC 950 (SEMKO, DEMKO,
NEMKO, SETI)
RFI: US model: FCC class B
European model: VDE0871, CISPR PUB.22
Interface specifications
Your printer is equipped with an 8-bit parallel interface with the following characteristics:
Data format: 8-bit parallel
Synchronization:
Handshake timing:
Signal level:
Connector:
STROBE pulse
BUSY and ACKNLG signals
TTL compatible
36-pin 57-30360 Amphenol connector or equivalent
Default settings
ActionPrinter 3250
Character Tables
These character tables are selected with the default-setting mode or by wing a software command. AU the tables are the same for hex codes 00 through 7F.
Therefore, only first table is shown completely. The rest of the tables show only the characters for hex codes 80 through FF.
For all character tables except the italic character table, the ESC 6 and ESC 7 software commands let you select whether hex codes 80 to 9F are characters (EX 6) or control codes (ESC 7).
PC 437 (USA, standard Europe)
Item
Top of farm position
Page length
Left and right margins
Line spacing
Character size
Horizontal tab positions
Font selection
Special printing effects
Download character set
Default setting
Current paper position or setting in the default setting mode.
Single sheets: 65 lines for A4-size paper,
61 lines for letter-size paper, 22 inches for manual insertion
Continuous paper: Subject to control panel setting in the default-setting mode
Canceled
1/6-inch tine spacing
10.5 point
Every eight characters
Last font selected on control panel
Canceled (except condensed printing)
Hardware initialization: cleared
Software initialization: deselected only
In addition, hardware initialization clears the data buffer.
Character available with ESC (^
To print the characters in the table below, you must first send the ESC (^ command.
24-Pin Printers
3/17/92
AP-3250-3
ActionPrinter 3250
The Control Panel
You can control the basic printer operations--form feeding, paper loading and ejecting, and font selection-with the buttons on the control panel. The indicator lights help you monitor the status of the printer.
FONT/YES button
FORM FEED/NO button r i m
PAPER PARK
If you are using continuous paper, you can press the FORM
FEED and
FONT buttons at the same time to move the paper back to the paperpark position.
CAUTION: Never feed labels backward through the printer; they may peel off their backing sheet and damage it. Use the
FORM FEED button to feed them forward.
Lights
The two panel lights provide information on certain printer conditions and settings.
READY
The
READY light is on when the printer is ready to receive data from the computer. It flashes briefly each time you turn on the printer.
The READY light also flashes under the following conditions: l
The printer is out of paper.
.
The printer is in the tear-off mode (when the optional push tractor is installed).
when an error
occurs, the READY light goes off.
FONT
The two
FONT lights indicate the
current
font setting. These lights change when you press
the FONT button. Look at the font menu on the control panel to determine which font is selected.
Buttons
The two buttons
on the control panel perform different functions, depending on the printer mode,
FONT/YES
Press the
FONT button during normal operation to cycle through the font choices on the font menu. The two
FONT lights indicate the
current selections.
When you are in the default-setting mode, use this button to enter a positive response to a printer question or to select a new default setting.
FORM FEED/NO
Press the FORM FEED button during normal operation to load a single sheet of paper or to advance continuous paper to the next top-ofform. You can also press FORM FEED to eject a page.
When you are in the default-setting mode, use this button to enter a
negative response to a
printer question or to skip to the next setting.
Other control-panel features
The control panel
also
gives you
access
to three special features:
Self Test The self test lets you check whether your printer is operating properly.
Hex dump The hex dump allows advanced users to pinpoint communications problems between the printer and computer.
Demonstration The demonstration page is a printout of text and type enhancements that shows you the unique capabilities of your printer.
Selecting Character Fonts
To
choose one of the fonts available with your printer, press the
FONT button.
FONT
t
wa
YES
The two FONT lights come on (O), go off (0), and Rash (8) to indicate the current selection. The table below lists the fonts and shows how the FONT lights appear for each selection.
@on Ooff Y flashing
The Roman and Sans Serif fonts can be scaled (or sized) from 8 to 32 points in 2-point increments, using your application software or
ESC/P2 commands.
AP-3250-4 3/17/92 24-Pin Printers
Changing Printer Settings
Make sure the printer is turned off and paper is loaded.
Remove the narrow cover from the printer.
The printer prints a series of questions about your printer settings. Press the
YES and
NO buttons to respond and make your changes. All new settings remain in effect until you change them again.
Note:
To enter the default settings mode, hold down the
YES button while you turn on the printer.
ActionPrinter 3250
To take full
advantage at your printer’s features, including ESC/P2, choose one of the first three printers on the list below. If none of these is listed, contact your software manufacturer for an update that includes one of the three. Until you receive an update, choose another printer as close to the top of the list as possible.
LQ-100
LQ-570
1
E S C / P 2
LQ870 J
LQ-510/550
LQ-860
LQ-850
LQ-200
1
FIX/P
LQ-500
LQ-2550
LQ-2500
LQ-800
LQ-1500
1
If none of these printers is listed among your program’s options, select the first available of the following: EX, FX, LX, RX, MX, Epson printer, Standard printer, Draft printer. Because these are 9-pin printers, however, your graphics printing may not be correct.
Turn off the printer at any time to exit the default settings mode; then replace the narrow cover.
You can change the printer settings listed here:
Setting
Character table
Page length
Skip over perforation
Tear-off position
TOF position
Graphic print direction
Download
Auto line feed
Options
437,850,860,863,865
11", 12", 8.5", 70/6" on. on
On cutter. Above cutter
-3, -2, -1, +0, +1, +2, +3
Hex dumo. Demonstration
Printing a Self Test
You can print a self test to make sure your printer operates properly.
1. Make sure the printer is turned off and paper is loaded.
2. Hold down the
FORM FEED button while you turn on the printer. It loads a sheet of paper automatically and begins to print characters in the current font and character table.
D
FF
3. To stop the self test, turn off the printer.
Application Software
Most application programs let you specify the type of printer you use so that the program can take full advantage of the printer’s features. Many programs provide an installation or setup m&u that presents a list of printers.
Paper Handling
Printing on Single Sheets
You can load standard-sized single sheets with the paper cassette and you can load single sheets of paper from
148 mm (5.8 inches) to
257 mm (10.1 inches) wide with the manual insertion slot.
Tips for using the paper cassette
The tips below help you get the best performance when printing with the cassette.
l l
.
Load paper in the paper cassette before you turn on the printer and send data. When the printer receives data from the computer, it loads a single sheet automatically and begins to print.
If the printer runs out of paper during a print job, reload the paper cassette and press the FORM FEED button to load the paper.
Press the FORM FEED button to eject a sheet of loaded paper.
You
can adjust the top-of-form position with the gear under the printer cover. It is marked by + and -signs. Open the printer cover and turn the gear to adjust the position. The notches on the ribbon mask indicate the base line of printed characters. The gear adjustment affects only the loaded page. If
you want to change the top-of-form position permanently, you can adjust it in the default-setting mode. However, most application software programs take care of the top and bottom margins. You usually don’t need to set the top-of-form position on the printer.
ribbon mask
--- base line of
characters
AP-3250-5
24-Pin Printers 3/17/92
ActionPrinter 3250 l
When you want to push the paper support
back into the paper
cassette, first remove paper from the paper cassette. Then push the paper support in while pushing
down on the locking tab.
Using Continuous Paper with Optional Push Tractor
You can use the
Optional push tractor to print on continuous paper
from 101 mm (4 inches) to 254 mm (10 inches) wide.
Installing the push tractor
1.
Make sure the printer is turned off and is in the flat position.
Remove the paper guide.
l
The default page length for the paper cassette is 65 lines
(A4-size
paper) or 61 lines (letter-size paper). You can change it using your application software or printer commands, if necessary.
l You can switch to manual insertion or to the optional push tractor without removing the paper cassette.
Loading paper manually
You can load single sheets of paper from the rear manual insertion slot. (If you’ve installed the optional push tractor, remove it before loading paper manually.)
1. Place the printer in the upright position and turn it on.
2. Next, lower the flap on the rear slot. Then insert a single sheet into the slot, aligning the paper edge with the arrow mark on the printer case. The page loads automatically. When the printer receives data, it begins printing.
2.
Make sure the paper-release lever is lowered to the single-sheet position.
3. Hold the tractor as shown and fit the edges of both sides into the slots at the back of the printer. Then lift it straight up until you hear the unit snap into place.
Be sure to raise the flap when not using manual insertion.
CAUTION: Be sure to turn on the printer
before you insert
the page into the slot. If you turn on the printer
after
paper insertion, the printer prints on the platen without loading the paper.
l l
You can adjust the top-of-form position in the same way that you do for paper loaded from the cassette.
When you want to switch to the paper cassette, press the
FORM
FEED button without inserting a page into the rear slot. The printer loads a page from the cassette.
4. Raise the paper-release lever to the continuous-paper position.
AP-3250-6 3/17/92 24-Pin Printers
Tips for using continuous paper
l You can adjust the top-of-form position temporarily. Open the printer cover and turn the gear marked by + and - signs to adjust the position This adjustment is lost when you turn off the printer or feed the paper backward to the paper-park position by pressing the FORM
FEED and FONT buttons at the same time.
4.
Replace the
paper guide.
ActionPrinter 3250 l l
If you want to change the top-of-form position permanently, adjust it with the default-setting mode.
Each time you turn on the printer with paper loaded, it reverses the continuous paper to the paper-park position and then advances it to the next top-of-form. Always remove your printed sheets before you turn off the printer to keep the top-of-form position accurate.
Removing the push tractor
1. Tear off any printed pages. Press the
FORM FEED and FONT buttons at the same time to feed the remaining paper backward to the paper-park position Remove the paper from the push tractor.
CAUTION: Always tear off the printed document and excess paper before feeding paper backward. Never feed more than one page backward through the printer.
2. Turn off the printer.
3. Lower the paper-release lever to the single sheet position. Then pull the push tractor straight down and out of the printer.
Switching Between Continuous Paper and Single
When you use the push tractor, you can easily switch to single-sheet printing without removing the continuous paper supply.
Switching to single sheets
Here’s how to switch from continuous paper to single sheets:
1. If you have a printed document stilI in the printer, tear off the printed pages and then press the FORM FEED and FONT buttons at the same time to reverse the remaining paper back to the paperpark position.
CD l
CAUTION:
Always tear off printed pages before feeding paper backward; feeding too many sheets backward can l cause a paper jam.
Never feed labels backward. They can easily peel off of their backing and jam the printer.
2. Lower the paper-release lever to the single-sheet position.
24-Pin Printers 3/17/92 AP-3250-7
ActionPrinter 3250
CAUTION; If you lower the paper-release lever while continuous paper is still loaded, the printer beeps and the
READY light goes off. If this release lever and
happens, raise the paper-
press the FORM FEED and FONT buttons at the same time to revense the paper to the paper-park position. You can then lower the lever again
3.
The printer is ready to print. When it receives data, it automatically loads a single sheet from the paper cassette and begins to print.
Switching to continuous paper
To switch from single sheets back to continuous paper, follow these steps:
1. If a single sheet is in the paper path, press the FORM
FEED button to eject it.
2. Raise the paper-release lever
to the push-tractor position.
Envelopes
You can use the manual insertion slot to print a individual envelopes.
Always load envelopes manuaIly through the
rear slot.
Before loading an envelope, set the paper-thickness lever to position 1 and lower the flap on the printer’s rear.
Always
feed envelopes by inserting the wide edge into the printer first, as shown.
3.
The printer is ready. When the printer receives data, it loads continuous paper from the push tractor automatically and begins to print.
Use envelopes under normal operating conditions only.
Printing on the edge of an envelope can damage the print head.
Make sure your application program keeps the printing entirely within the printable area of the envelope.
Printing on Special Paper
In addition to printing on single sheets and continuous paper, your printer can print on a wide variety of other paper types, such as envelopes, labels, and multi-part forms.
Adjusting the paper-thickness lever
Before you print on special paper, you may need to change the paper-thickness setting for the paper you are using.
1. Remove the printer cover and set the paper-thickness lever to match the thickness of your paper. Choose the setting from the table below.
Paper Type
Lever Position l-
1
Note: Setting the paper-thickness level to 1 reduces the printing speed.
2.
Replace the cover.
AP-3250-8 3/17/92
Installation/Support Tips
AP-3250 Beep Codes
2 Long and 2 Short = Indicates that the printer has completed its power-on initialization process and is ready to print
1 Short =
3 Short =
5 Long =
The escape code for “BEL” has been received
Paper out condition
Illegal paper change condition* or a printer fatal error** l = 1) The optional pull tractor’s paper release lever was set to the TRACTOR position without first ejecting the cutsheet paper.
2)
The optional pull tractor’s release lever was set to the
FRICTION position without first ejecting the continuous paper.
** =
1)
2)
3)
4)
Power supply voltage error
Internal air temperature error
Print head temperature error
Line feed or carriage motor is overheated
Short beep = 100ms beep with 100ms pause between beeps
Long beep = 500 ms beep with 500ms pause between beeps
24-Pin Printers
Information Reference List
Engineering Change Notices
None.
Product Support Bulletins
None.
Technical Information Bulletins
None.
Related Documentation
TM-AP3250 ActionPrinter 3250 Service Manual
PL-AP3250
4000928 GO1-00
ActionPrinter 3250 Parts List
ActionPrinter 3250 User’s Guide
ActionPrinter 3250
24-Pin Printers AP-3250-9
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
Frequently Answers and Questions
What paper weights and thicknesses are compatible with the Epson ActionPrinter 3250?
What character sets and graphics character tables does the Epson ActionPrinter 3250 support?
What is the maximum printable width of the Epson ActionPrinter 3250?
What paper-feed methods does the Epson ActionPrinter 3250 support?
What is the rated voltage and input voltage range for the Epson ActionPrinter 3250?
advertisement
Table of contents
- 1 Printer Specifications
- 1 Printing
- 1 Paper
- 2 Mechanical
- 2 Electrical
- 3 Environmental
- 3 Interface specifications
- 3 Default settings
- 3 Character Tables
- 4 The Control Panel
- 4 Lights
- 4 Buttons
- 4 Paper park
- 4 Ohter control-panel features
- 4 Selecting character fonts
- 5 Changing Printer Settings
- 5 Printing a Self Test
- 5 Application Software
- 5 Paper Handling
- 5 Printing on single sheets
- 6 Loading paper manually
- 6 Using continuous paper with optional push tractor
- 6 Installing the push tractor
- 7 Tips fo rusing continuous paper
- 7 Removing the push tractor
- 7 Switching between continuous paper and single
- 8 Printing on special paper
- 8 Installation/support tips
- 8 AP-3250 beep codes
- 9 Information Reference List
- 9 Related documentation