Sharp Aquos LC-40LE600S Service manual

LC-40/46/52/60LE810UN (1st Edition)
SERVICE MANUAL
No. S30E840LE810U
LCD COLOR TELEVISION
MODELS
LC-40LE810UN
LC-46LE810UN
LC-52LE810UN
LC-60LE810UN
In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified should be used.
CONTENTS
SAFETY PRECAUTION
IMPORTANT SERVICE SAFETY
PRECAUTION.....................................................i
PRECAUTIONS A PRENDRE LORS DE
LA REPARATION ...............................................ii
PRECAUTIONS FOR USING LEAD-FREE
SOLDER ........................................................... iii
OUTLINE
MAJOR SERVICE PARTS ................................iv
CHAPTER 1. SPECIFICATIONS
[1] SPECIFICATIONS (LC-40/46LE810UN)........ 1-1
[2] SPECIFICATIONS (LC-52/60LE810UN)........ 1-2
CHAPTER 2. OPERATION MANUAL
[1] Parts Name .................................................... 2-1
[2] OPERATION MANUAL .................................. 2-3
CHAPTER 3. DIMENSIONS
[1] DIMENSIONS (LC-40LE810UN).................... 3-1
[2] DIMENSIONS (LC-46LE810UN).................... 3-2
[3] DIMENSIONS (LC-52LE810UN).................... 3-3
[4] DIMENSIONS (LC-60LE810UN).................... 3-4
[2]
[3]
[4]
REMOVING OF MAJOR PARTS
(LC-46LE810UN)...........................................4-6
REMOVING OF MAJOR PARTS
(LC-52LE810UN)......................................... 4-11
REMOVING OF MAJOR PARTS
(LC-60LE810UN).........................................4-16
CHAPTER 5. ADJUSTMENT
[1] ADJUSTMENT PROCEDURE ......................5-1
[2] PUBLIC MODE SETTING PROCEDURE
......5-15
CHAPTER 6. TROUBLESHOOTING TABLE
[1] TROUBLESHOOTING TABLE ......................6-1
[2] LED flashing specification at the time of an
error (Center icon LED used) ......................6-14
CHAPTER 7. MAJOR IC INFORMATIONS
[1] MAJOR IC INFORMATIONS .........................7-1
CHAPTER 8. OVERALL WIRING/SYSTEM BLOCK
DIAGRAM
[1] OVERALL WIRING DIAGRAM ......................8-1
[2] SYSTEM BLOCK DIAGRAM .........................8-2
Parts Guide
CHAPTER 4. REMOVING OF MAJOR PARTS
[1] REMOVING OF MAJOR PARTS
(LC-40LE810UN) ........................................... 4-1
Parts marked with "
" are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the
safety and performance of the set.
This document has been published to be used for
after sales service only.
The contents are subject to change without notice.
LC-40/46/52/60LE810UN (1st Edition)
LC-40LE810UN
SAFETY PRECAUTION
Service Manual
IMPORTANT SERVICE SAFETY PRECAUTION
Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and the
servicing guidelines which follow:
„WARNING
•
Using two clip leads, connect a 1.5k ohm, 10 watt resistor paralleled by a 0.15µF capacitor in series with all exposed metal cabinet
parts and a known earth ground, such as electrical conduit or electrical ground connected to an earth ground.
•
Use an AC voltmeter having with 5000 ohm per volt, or higher, sensitivity or measure the AC voltage drop across the resistor.
•
Connect the resistor connection to all exposed metal parts having a
return to the chassis (antenna, metal cabinet, screw heads, knobs
and control shafts, escutcheon, etc.) and measure the AC voltage
drop across the resistor.
1. For continued safety, no modification of any circuit should be
attempted.
2. Disconnect AC power before servicing.
C A U T I O N : F O R C O N T I N U E D PROTECTION
AGAINST A RISK OF FIRE REPLACE ONLY WITH
SAME TYPE FUSE.
All checks must be repeated with the AC cord plug connection
reversed. (If necessary, a nonpolarized adaptor plug must be used
only for the purpose of completing these checks.)
F7000 (250V 3.5A) (LC-40LE810UN)
F7001 (250V 3.5A) (LC-40LE810UN)
Any reading of 0.75 Vrms (this corresponds to 0.5 mA rms AC.) or
more is excessive and indicates a potential shock hazard which
must be corrected before returning the monitor to the owner.
F7000 (250V 5A) (LC-46/52/60LE810UN)
F7001 (250V 5A) (LC-46/52/60LE810UN)
„BEFORE RETURNING THE RECEIVER (Fire &
Shock Hazard)
DVM
AC SCALE
Before returning the receiver to the user, perform the following
safety checks:
1.5k ohm
10W
3. Inspect all lead dress to make certain that leads are not pinched,
and check that hardware is not lodged between the chassis and
other metal parts in the receiver.
4. Inspect all protective devices such as non-metallic control knobs,
insulation materials, cabinet backs, adjustment and compartment
covers or shields, isolation resistor-capacitor networks, mechanical
insulators, etc.
0.15 µF
TEST PROBE
5. To be sure that no shock hazard exists, check for leakage current in
the following manner.
•
Plug the AC cord directly into a 120 volt AC outlet.
TO EXPOSED
METAL PARTS
CONNECT TO
KNOWN EARTH
GROUND
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
SAFETY NOTICE
Many electrical and mechanical parts in LCD color television have
special safety-related characteristics.
For continued protection, replacement parts must be identical to those
used in the original circuit.
These characteristics are often not evident from visual inspection, nor
can protection afforded by them be necessarily increased by using
replacement components rated for higher voltage, wattage, etc.
The use of a substitute replacement parts which do not have the same
safety characteristics as the factory recommended replacement parts
shown in this service manual, may create shock, fire or other hazards.
Replacement parts which have these special safety characteristics are
identified in this manual; electrical components having such features
are identified by "
" and shaded areas in the Replacement Parts List
and Schematic Diagrams.
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
i
LC-40/46/52/60LE810UN (1st Edition)
PRECAUTIONS A PRENDRE LORS DE LA REPARATION
Ne peut effectuer la réparation qu' un technicien spécialisé qui s'est parfaitement accoutumé à toute vérification de sécurité et aux
conseils suivants.
AVERTISSEMENT
• A l'aide de deux fils à pinces, brancher une résistance de 1.5 kΩ
10 watts en parallèle avec un condensateur de 0.15µF en série
avec toutes les pièces métalliques exposées du coffret et une terre
connue comme une conduite électrique ou une prise de terre
branchée à la terre.
1. N'entreprendre aucune modification de tout circuit. C'est dangereux.
2. Débrancher le récepteur avant toute réparation.
• Utiliser un voltmètre CA d'une sensibilité d'au moins 5000Ω/V pour
mesurer la chute de tension en travers de la résistance.
PRECAUTION: POUR LA PROTECTION CONTINUE CONTRE LES RISQUES D'INCENDIE,
REMPLACER LE FUSIBLE
• Toucher avec la sonde d'essai les pièces métalliques exposées qui
présentent une voie de retour au châssis (antenne, coffret métallique, tête des vis, arbres de commande et des boutons, écusson,
etc.) et mesurer la chute de tension CA en-travers de la résistance.
Toutes les vérifications doivent être refaites après avoir inversé la
fiche du cordon d'alimentation. (Si nécessaire, une prise
d'adpatation non polarisée peut être utilisée dans le but de terminer ces vérifications.)
La tension de pointe mesurèe ne doit pas dépasser 0.75V (correspondante au courant CA de pointe de 0.5mA).
Dans le cas contraire, il y a une possibilité de choc électrique qui
doit être supprimée avant de rendre le récepteur au client.
F7000 (250V 3.5A) (LC-40LE810UN)
F7001 (250V 3.5A) (LC-40LE810UN)
F7000 (250V 5A) (LC-46/52/60LE810N)
F7001 (250V 5A) (LC-46/52/60LE810UN)
VERIFICATIONS CONTRE L'INCEN-DIE ET LE
CHOC ELECTRIQUE
Avant de rendre le récepteur à l'utilisateur, effectuer les vérifications suivantes.
DVM
ECHELLE CA
3. Inspecter tous les faisceaux de câbles pour s'assurer que les fils
ne soient pas pincés ou qu'un outil ne soit pas placé entre le châssis et les autres pièces métalliques du récepteur.
1.5k ohm
10W
4. Inspecter tous les dispositifs de protection comme les boutons de
commande non-métalliques, les isolants, le dos du coffret, les couvercles ou blindages de réglage et de compartiment, les réseaux
de résistancecapacité, les isolateurs mécaniques, etc.
0.15 µF
SONDE D'ESSAI
5. S'assurer qu'il n'y ait pas de danger d'électrocution en vérifiant la
fuite de courant, de la facon suivante:
•
Brancher le cordon d'alimentation directem-ent à une prise de courant de 120V. (Ne pas utiliser de transformateur d'isolation pour
cet essai).
AUX PIECES
METALLIQUES
EXPOSEES
BRANCHER A UNE
TERRE CONNUE
/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
AVIS POUR LA SECURITE
Pour assurer la protection, ces pièces doivent être identiques à celles
utilisées dans le circuit d'origine. L'utilisation de pièces qui n'ont pas
les mêmes caractéristiques que les pièces recommandées par l'usine,
indiquées dans ce manuel, peut provoquer des électrocutions, incendies, radiations X ou autres accidents.
De nombreuses pièces, électriques et mécaniques, dans les téléviseur ACL présentent des caractéristiques spéciales relatives à la sécurité, qui ne sont souvent pas évidentes à vue. Le degré de protection ne peut pas être nécessairement augmentée en utilisant des
pièces de remplacement étalonnées pour haute tension, puissance,
etc.
Les pièces de remplacement qui présentent ces caractéristiques sont
identifiées dans ce manuel; les pièces électriques qui présentent ces
particularités sont identifiées par la marque " " et hachurées dans la
liste des pièces de remplacement et les diagrammes schématiques.
/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
ii
LC-40/46/52/60LE810UN (1st Edition)
PRECAUTIONS FOR USING LEAD-FREE SOLDER
„Employing lead-free solder
•
“PWBs” of this model employs lead-free solder. The LF symbol indicates lead-free solder, and is attached on the PWBs and service manuals. The
alphabetical character following LF shows the type of lead-free solder.
Example:
Indicates lead-free solder of tin, silver and copper.
Indicates lead-free solder of tin, silver and copper.
„Using lead-free wire solder
•
When fixing the PWB soldered with the lead-free solder, apply lead-free wire solder. Repairing with conventional lead wire solder may cause damage or accident due to cracks.
As the melting point of lead-free solder (Sn-Ag-Cu) is higher than the lead wire solder by 40 °C, we recommend you to use a dedicated soldering
bit, if you are not familiar with how to obtain lead-free wire solder or soldering bit, contact our service station or service branch in your area.
„Soldering
•
As the melting point of lead-free solder (Sn-Ag-Cu) is about 220 °C which is higher than the conventional lead solder by 40 °C, and as it has poor
solder wettability, you may be apt to keep the soldering bit in contact with the PWB for extended period of time. However, Since the land may be
peeled off or the maximum heat-resistance temperature of parts may be exceeded, remove the bit from the PWB as soon as you confirm the
steady soldering condition.
Lead-free solder contains more tin, and the end of the soldering bit may be easily corroded. Make sure to turn on and off the power of the bit as
required.
If a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit after every use of it.
When the tip of the soldering bit is blackened during use, file it with steel wool or fine sandpaper.
•
Be careful when replacing parts with polarity indication on the PWB silk.
Lead-free wire solder for servicing
PARTS CODE
ZHNDAi123250E
ZHNDAi126500E
ZHNDAi12801KE
PRICE
RANK
BL
BK
BM
PART
DELIVERY
J
J
J
DESCRIPTION
φ0.3mm 250g (1roll)
φ0.6mm 500g (1roll)
φ1.0mm 1kg (1roll)
iii
LC-40/46/52/60LE810UN (1st Edition)
LC-40LE810UN
OUTLINE
Service Manual
MAJOR SERVICE PARTS
„PWB UNIT
Ref No.
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Part No.
DKEYMF452FM01
DUNTKF493FM01
DUNTKF494FM01
RUNTKA692WJQZ
RUNTKA682WJQZ
RUNTKA683WJQZ
RUNTKA693WJQZ
RUNTKA684WJQZ
RUNTKA692WJQZ
RUNTK4437TPZZ
RUNTK4437TPZA
RUNTK4437TPZB
RUNTK4437TPZC
RUNTK4462TPZZ
RUNTK4461TPZZ
RUNTK4460TPZZ
RUNTK4458TPZZ
RUNTK4459TPZZ
MAIN Unit *1
ICON Unit
R/C LED Unit
KEY Unit
POWER/LED Drive Unit (LC-40LE810UN)
POWER/LED Drive Unit (LC-46LE810UN)
POWER/LED Drive Unit (LC-52LE810UN)
POWER/LED Drive Unit (LC-60LE810UN)
TOUCH SENSOR Unit *2
LCD CONTROL Unit (LC-40LE810UN)
LCD CONTROL Unit (LC-46LE810UN)
LCD CONTROL Unit (LC-52LE810UN)
LCD CONTROL Unit (LC-60LE810UN)
LED PWB Unit (LC-40LE810UN), x4
LED PWB Unit (LC-46LE810UN), x4
LED PWB Unit (LC-52LE810UN), x4
LED PWB Unit (LC-60LE810UN), x4
LED PWB Unit (LC-60LE810UN), x4
Description
Part No.
R1LK400D3LWF2Z
R1LK460D3LWA2Z
R1LK520D3LWA2Z
R1LK600D3LW2BZ
40” LCD Panel Module Unit
46” LCD Panel Module Unit
52” LCD Panel Module Unit
60” LCD Panel Module Unit
„OTHER UNIT
Ref No.
N
N
N
N
Description
„IC FOR EXCLUSIVE USE OF THE SERVICE
Ref No.
IC509
IC2002
Part No.
VHiR24002AS1YS
RH-iXC786WJNHQ
Description
R1EX24002ASAS0A (RGB EDID)
R5F364A6NFB (MICON)
Therefore, please exchange of a touch sensor unit in the
case of front cabinet exchange.
NOTE: *1 Replace MAIN PWB Units (DKEYMF452FM01) in case of
IC8401 or IC3302 failure.
*2 TOUCH SENSOR Unit (RUNTKA692WJQZ) reuse will be
impossible, once it is stuck on front cabinet and exfoliates.
Ref No.
N
N
N
N
N
Part No.
QCNW-C222WJQZ
QCNW-H184WJQZ
QCNW-F676WJQZ
QCNW-G405WJQZ
QCNW-G394WJQZ
Connecting Cord
Connecting Cord
Connecting Cord
Connecting Cord
Connecting Cord
Q'ty
1
1
„SERVICE JIGS
L=1000mm
L=1000mm
L=1000mm
L=1000mm
L=1000mm
iv
Description
80pin LCD Control to LCD Panel Unit x2
12pin Main to Power Unit (PD)
41pin Main to LCD Control (LW)
4pin Main to LCD Control (PL)
9pin Main to Power (LB)
Q'ty
2
1
1
1
1
LC-40/46/52/60LE810UN (1st Edition)
CHAPTER 1. SPECIFICATIONS
LC-40LE810UN
Service Manual
[1] SPECIFICATIONS (LC-40/46LE810UN)
Item
Model: LC-40LE810UN
Size
LCD
panel
TV
Function
40" Class (40" Diagonal)
Model: LC-46LE810UN
63
46" Class (45 /64" Diagonal)
Resolution
2,073,600 pixels (1,920 x 1,080)
TV-standard (CCIR)
American TV Standard ATSC/NTSC System
Receiving
Channel
VHF/UHF
VHF 2-13ch, UHF 14-69ch
CATV
1-135ch (non-scrambled channel only)
Digital Terrestrial
2-69ch
Broadcast (8VSB)
*1
Digital cable
(64/256 QAM)
Audio multiplex
Audio out
1-135ch (non-scrambled channel only)
BTSC System
10W x 2 + 15W (WF)
INPUT 2
AV in (AV mini plug and RCA plugs)
INPUT 3
ANALOG RGB (PC) in (15-pin mini D-sub female connector),
Audio in (Ø 3.5 mm stereo jack)
INPUT 4
HDMI in with HDCP, Audio in (Ø 3.5 mm stereo jack)
INPUT 5
HDMI in with HDCP
INPUT 6
HDMI in with HDCP
Back panel
INPUT 7
vertical
inputs
AUDIO IN
Terminals
AUDIO OUT
HDMI in with HDCP
Audio in (Ø 3.5 mm stereo jack)
Audio out (Ø 3.5 mm stereo jack)
DIGITAL AUDIO OUTPUT Optical Digital audio output x 1 (PCM/Dolby Digital)
ETHERNET
Network connector
USB 1
Photo/Music mode, Software update
USB 2
Photo/Music mode, Software update
INPUT 1
Back panel
horizontal ANT/CABLE
inputs
RS-232C
COMPONENT in
75 Ω Unbalance, F Type x 1 for Analog (VHF/UHF/CATV) and Digital (AIR/CABLE)
9-pin D-sub male connector
OSD language
English/French/Spanish
Power Requirement
AC 120 V, 60 Hz
Power Consumption
140 W (0.5 W Standby with AC 120 V) 160 W (0.5 W Standby with AC 120 V)
Weight
*2
Dimension
(W x H x D)
Operating temperature
TV + stand
43.0 lbs./19.5 kg
TV only
35.3 lbs./16.0 kg
1
13
1
59
57.3 lbs./26.0 kg
45.2 lbs./20.5 kg
27
TV + stand
39 /16 x 27 /16 x 10 /32 inch
TV only
39 /16 x 25 /64 x 1 /64 inch
37
19
7
19
7
25
44 /64 x 30 /8 x 13 /64 inch
37
44 /64 x 28 /8 x 1 /64 inch
+32°F to +104°F (0°C to +40°C)
Cautions regarding use in high and low temperature environments
• When the unit is used in a low temperature space (e.g. room, office), the picture may leave trails or appear slightly delayed.
This is not a malfunction, and the unit will recover when the temperature returns to normal.
• Do not leave the unit in a hot or cold location. Also, do not leave the unit in a location exposed to direct sunlight or near a
heater, as this may cause the cabinet to deform and the Liquid Crystal panel to malfunction.
Storage temperature:-4°F to + 140°F (-20°C to + 60°C)
1–1
LC-40/46/52/60LE810UN (1st Edition)
[2] SPECIFICATIONS (LC-52/60LE810UN)
Item
Model: LC-52LE810UN
1
Size
LCD
panel
TV
Function
52" Class (52 /32" Diagonal)
Model: LC-60LE810UN
1
60" Class (60 /32 Diagonal)
Resolution
2,073,600 pixels (1,920 x 1,080)
TV-standard (CCIR)
American TV Standard ATSC/NTSC System
Receiving
Channel
VHF/UHF
VHF 2-13ch, UHF 14-69ch
CATV
1-135ch (non-scrambled channel only)
Digital Terrestrial
2-69ch
Broadcast (8VSB)
*1
Digital cable
(64/256 QAM)
Audio multiplex
Audio out
1-135ch (non-scrambled channel only)
BTSC System
10W x 2 + 15 W (WF)
INPUT 2
AV in (AV mini plug and RCA plugs)
INPUT 3
ANALOG RGB (PC) in (15-pin mini D-sub female connector),
Audio in (Ø 3.5 mm stereo jack)
INPUT 4
HDMI in with HDCP, Audio in (Ø 3.5 mm stereo jack)
INPUT 5
HDMI in with HDCP
INPUT 6
Back panel
INPUT 7
vertical
inputs
AUDIO IN
Terminals
AUDIO OUT
HDMI in with HDCP
HDMI in with HDCP
Audio in (Ø 3.5 mm stereo jack)
Audio out (Ø 3.5 mm stereo jack)
DIGITAL AUDIO OUTPUT Optical Digital audio output x 1 (PCM/Dolby Digital)
ETHERNET
Network connector
USB 1
Photo/Music mode, Software update
USB 2
Photo/Music mode, Software update
INPUT 1
Back panel
horizontal ANT/CABLE
inputs
RS-232C
OSD language
COMPONENT in
75 Ω Unbalance, F Type x 1 for Analog (VHF/UHF/CATV) and Digital (AIR/CABLE)
9-pin D-sub male connector
English/French/Spanish
Power Requirement
AC 120 V, 60 Hz
Power Consumption
170 W (0.5 W Standby with AC 120 V) 230 W (0.5 W Standby with AC 120 V)
Weight
*2
Dimension
(W x H x D)
TV + stand
66.1 lbs./30.0 kg
TV only
54.0 lbs./24.5 kg
37
29
37
57
95.9 lbs./43.5 kg
71.7 lbs./32.5 kg
25
TV + stand
49 /64 x 33 /32 x 13 /64 inch
TV only
49 /64 x 31 /64 x 1 /64 inch
Operating temperature
37
5
23
5
59
1
56 /8 x 38 /64 x 14 /2 inch
37
56 /8 x 35 /64 x 1 /64 inch
+32°F to +104°F (0°C to +40°C)
*1
Emergency alert messages via Cable are unreceivable.
The dimensional drawings are shown on the inside back cover.
• As part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for
product improvement without prior notice. The performance specification figures indicated are nominal values of production
units. There may be some deviations from these values in individual units.
*2
Part name
Wall mount
bracket
The listed optional accessory is available for the Liquid
Crystal Television. Please purchase it at your nearest shop. Attachment
• Additional optional accessories may be available in the near
future. When purchasing, please read the newest catalogue for Wall mount
bracket
compatibility and check the availability.
Optional Accessory
1–2
Model number
AN-37AG2 (for LC-40LE810UN)
AN-37P30 (for LC-40LE810UN)
AN-52AG4
(for LC-46LE810UN/LC-52LE810UN/
LC-60LE810UN)
LC-40/46/52/60LE810UN (1st Edition)
CHAPTER 2. OPERATION MANUAL
LC-40LE810UN
Service Manual
[1] Parts Name
TV (Front)
Center Icon illumination
Remote control sensor
OPC sensor*1
VOLl /k
CHu /t
INPUT POWER *2
MENU
*1 OPC: Optical Picture Control
*2 Using the touch sensor panel.
TV (Rear)
*1
USB 1 terminal
ETHERNET terminal
AUDIO OUT terminal
INPUT 2 terminal
INPUT 3 terminal (PC-IN)
AUDIO IN terminal
(shared for INPUT 3 and INPUT 4) *2
INPUT 4 terminal (HDMI)
ARC: Audio Return Channel
INPUT 5 terminal (HDMI)
*1
INPUT 6 terminal (HDMI)
INPUT 7 terminal (HDMI)
DIGITAL AUDIO OUTPUT terminal
Antenna/Cable in
RS-232C terminal
INPUT 1 terminals
USB 2 terminal
*1 External equipment connection.
*2 Details on the Audio Select function.
• The illustrations in this operation manual are for explanation purposes and may vary slightly from the actual operations.
• The examples used throughout this manual are based on the LC-52LE810UN model.
2–1
LC-40/46/52/60LE810UN (1st Edition)
Remote Control Unit
1
POWER: Switch the TV power on or enter standby.
2
TV, STB, DVD • VCR, AUDIO: Switches the remote control for
TV, STB, DVD, BD, VCR and AUDIO operation.
1
2
19
3
20
External equipment operational buttons: Operate the external
equipment.
4
OPTION: Display the Link Operation Menu screen. This button
will function only when AQUOS LINK is used.
SLEEP: Set the sleep timer.
5
3
4
5
* To enter the code registration mode, you need to press an
appropriate button (STB, DVD • VCR or AUDIO) and DISPLAY
at the same time.
21
22
6
0–9: Set the channel.
7
• (DOT):
8
CC: Display captions from a closed-caption source.
9
AV MODE: Select an audio or video setting.
10 MUTE: Mute the sound.
11 VOL
/
: Set the volume.
6
12 MENU: Display the menu screen.
7
23
15 EXIT: Turn off the menu screen.
8
9
10
11
12
24
25
13
28
13 AQUOS NET: Switches the display to the Sidebar Widget,
TV Web, Web or TV screen.
14
26
27
14
15
16
17
18
/
/
/ , ENTER: Select a desired item on the screen.
16 SURROUND: Select Surround settings.
17 FAVORITE CH: Set the favorite channels.
18 A, B, C, D: Select 4 preset favorite channels in 4 different
categories.
While watching, you can toggle the selected channels by pressing
A, B, C and D.
19 DISPLAY: Display the channel information.
20 POWER (SOURCE): Turns the power of the external equipment
on and off.
21 REC STOP: Stops one touch recording. This button will function
only when AQUOS LINK is used.
22 POWER SAVING: Select Power Saving settings.
23 ENT: Jumps to a channel after selecting with the 0–9 buttons.
29
30
31
24 FLASHBACK: Return to the previous channel or external input
mode.
25 VIEW MODE: Select the screen size.
26 INPUT: Select a TV input source. (TV, INPUT 1, INPUT 2, INPUT 3,
INPUT 4, INPUT 5, INPUT 6, INPUT 7)
27 CH
/
: Select the channel.
28 DOCK: Display the DOCK.
29 RETURN: Return to the previous menu screen.
30 AUDIO: Selects the MTS/SAP or the audio mode during multichannel audio broadcasts.
31 FREEZE: Set the still image. Press again to return to normal
screen.
• When using the remote control unit, point it at the TV.
2–2
LC-40/46/52/60LE810UN (1st Edition)
[2] OPERATION MANUAL
Attaching the Stand
• Before attaching (or detaching) the stand, unplug the AC cord.
• Before performing work spread cushioning over the base area to lay the TV on. This will prevent it from being damaged.
CAUTION
• Attach the stand in the correct direction.
• Do not remove the stand from the TV unless using an optional wall mount bracket to mount it.
• Be sure to follow the instructions. Incorrect installation of the stand may result in the TV falling over.
1
Confirm that there are 9 screws (5 short screws
and 4 long screws) supplied with the stand unit.
4
2
Attach the supporting post for the stand unit onto
the base using the box for the stand unit as shown
below.
Insert and tighten the 4 screws into the 4 holes on
the rear of the stand unit.
Short screws
• The supporting post attaches to the base at an offcentered location on the base. Be sure to attach the
supporting post in the direction indicated below and
attach the stand to the TV with the wider side of the
base facing forward.
Long screws
5
1
2
Insert the stand cover.
Insert the screw to secure the stand cover.
Short screw
3
Insert the stand into the openings on the rear of the
TV.
2
1
Soft cushion
• To detach the stand, perform the steps in reverse
order.
2–3
LC-40/46/52/60LE810UN (1st Edition)
CHAPTER 3. DIMENSIONS
LC-40LE810UN
Service Manual
[1] DIMENSIONS (LC-40LE810UN)
Unit: inch (mm)
15 59/ 64
(404)
19 45/ 64
(500.4)
25 59/ 64 (658)
34 61/ 64 (887.8)
17 47/ 64 (450)
1 57/ 64
(48)
27 13/ 16 (706)
39 1/ 16 (992)
1 37/ 64
(40)
4 57/ 64
(124)
11 13/ 16 (300)
5 13/ 64
(132)
11 13/ 16 (300)
AN-37P30
+
AN-37AG2
10 27/ 32
(275)
3–1
3 7/ 16
(87)
1 37/ 64
(40)
5 (127)
LC-40/46/52/60LE810UN (1st Edition)
[2] DIMENSIONS (LC-46LE810UN)
Unit: inch (mm)
44 19/ 64 (1125)
17 31/ 64 (444)
28 7/ 8 (733)
22 21/ 32
(575.4)
21 17/ 64 (540)
2 1/ 64
(51)
30 7/ 8 (784)
40 13/ 64 (1020.8)
1 37/ 64
(40)
6 15/ 64
(158)
AN-52AG4
15 3/ 4 (400)
8 5/ 16
(211)
15 3/ 4 (400)
13 25/ 64
(340)
3–2
2 41/ 64
(67)
1 37/ 64
(40)
4 7/ 32
(107)
LC-40/46/52/60LE810UN (1st Edition)
[3] DIMENSIONS (LC-52LE810UN)
Unit: inch (mm)
19 1/ 16 (484)
45 15/ 32 (1154.8)
25 5/ 8
(650.8)
31 57/ 64 (810)
(1259)
21 17/ 64 (540)
2 1/ 64
(51)
33 29/ 32 (861)
49
37/ 64
1 37/ 64
(40)
6 15/ 64
(158)
AN-52AG4
15 3/ 4 (400)
6 25/ 32
(172)
15 3/ 4 (400)
13 25/ 64
(340)
3–3
2 41/ 64
(67)
1 37/ 64
(40)
4 7/ 32
(107)
LC-40/46/52/60LE810UN (1st Edition)
[4] DIMENSIONS (LC-60LE810UN)
Unit: inch (mm)
56 5/ 8 (1438)
21 1/ 2 (546)
29 35/ 64
(750.4)
35 59/ 64 (912)
22 27/ 32 (580)
2 29/ 64
(62)
38 23/ 64 (974)
52 7/ 16 (1331.8)
1 37/ 64
(40)
6 55/ 64
(174)
AN-52AG4
15 3/ 4 (400)
4 49/ 64
(121)
15 3/ 4 (400)
14
1/ 2
(368)
2 41/ 64
(67)
1 37/ 64
(40)
4 7/ 32
(107)
3–4
LC-40/46/52/60LE810UN (1st Edition)
Service
CHAPTER 4. REMOVING OF MAJOR PARTS
LC-40LE810UN
Manual
[1] REMOVING OF MAJOR PARTS (LC-40LE810UN)
1. Removing of Stand Unit and Rear Cabinet Ass’y.
1. Remove the 1 lock screw
2. Detach the Stand cover
and detach the AC code cover
.
.
3. Remove the 2 lock screw
and detach the Stand Ass’y
4. Remove the 4 lock screw
, 1 lock screw
.
, 4 lock screws
and 12 lock screws
and detach the Rear Cabinet Ass’y.
Rear Cabinet Ass'y
9
AC Cord Cover Ass'y 2
1
6
7
4
Stand Cover 3
8
Stand Ass'y 5
4–1
LC-40/46/52/60LE810UN (1st Edition)
2. Removing of Speaker-L/R.
1. Remove the 1 lock screw
and detach the Stand cover
.
2. Disconnect SP wire.
3. Detach the Speaker-L
, Speaker-R
.
MAIN Unit
[SP]
[SP]
Speaker-R 4
3 Speaker-L
2 Stand Cover
1
4–2
LC-40/46/52/60LE810UN (1st Edition)
3. Removing of LCD Panel Module, TOUCH SENSOR Unit, ICON Unit, R/C, LED Unit, Front Cabinet Ass’y.
1. Remove the 1 lock screw
and detach the LCD Fixing Metal Angle B-R
2. Remove the 5 lock screws
, 3 lock screws
.
, 4 Hooks and detach the LCD Panel Module
3. Disconnect RA wire.
4. Disconnect Touch Sensor Unit
5. Detach the ICON Unit
.
.
6. Detach the R/C, LED Unit
.
LED Panel
5 Module
4
3
3
4
[RA]
3
3
LCD Fixing
Metal Angle B-R
3
2
Hook
Hook
Hook
Hook
[RI]
R/C,
8
LED Unit
[RA] [RK]
1
Front Cabinet Ass'y
7 ICON Unit
6 TOUCH SENSOR Unit
4–3
LC-40/46/52/60LE810UN (1st Edition)
4. Removing of Connectors
1. Disconnect the following connectors from the MAIN Unit. (SB, LB, PD, LW)
2. Disconnect the following connectors from the POWER/ LED DRIVE Unit. (L1, L2, LB, PD)
3. Disconnect the following connectors from the LCD Control Unit. (LW, PL)
POWER/LED DRIVE Unit
MAIN Unit
[LW]
[PL]
LCD Control Unit
POWER/LED DRIVE Unit
MAIN Unit
[SB]
[L1]
[L2]
[LB]
[LB]
[PD]
[PD]
[LW]
[PL]
4–4
LC-40/46/52/60LE810UN (1st Edition)
5. Removing of MAIN Unit, POWER/LED DRIVE Unit, Sub Woofer, Stand Angle Ass’y
1. Remove the 7 lock screws
and detach the MAIN Unit
2. Remove the 2 lock screws
and detach the TERMINAL Angle B
.
3. Remove the 2 lock screws
and detach the TERMINAL Angle S
.
4. Remove the 6 lock screws
and detach the POWER/LED DRIVER Unit
5. Remove the 4 lock screws
and detach the Sub Woofer
6. Remove the 8 lock screws
and detach the 2 VESA Angle
.
.
.
7. Remove the 1 lock screw
and detach the LCD Fixing Metal Angle B-L
.
8. Remove the 1 lock screw
and detach the LCD Fixing Metal Angle T-R
.
9. Remove the 1 lock screw
and detach the LCD Fixing Metal Angle T-L
.
VESA
Angle
17
11
12
15
11
LCD Fixing Metal
Angle T-L 18
16 LCD Fixing
Metal Angle T-R
7
9
1
2 MAIN Unit
5
10
SUB
Woofer
[SB]
8 POWER/
LED
DRIVE
Unit
6 TERMINAL Angle S
4 TERMINAL Angle B
3
[L1]
[L2]
LED Panel
Module
LCD Fixing
14
Metal Angle B-L
13
20 Stand Angle Ass'y
19
4–5
LC-40/46/52/60LE810UN (1st Edition)
[2] REMOVING OF MAJOR PARTS (LC-46LE810UN)
1. Removing of Stand Unit and Rear Cabinet Ass’y.
1. Remove the 1 lock screw
2. Detach the Stand cover
and detach the AC code cover Ass’y
.
.
3. Remove the 2 lock screws
and detach the Stand Ass’y
4. Remove the 4 lock screws
, 1 lock screw
.
, 4 lock screws
and 16 lock screws
and detach the Rear Cabinet Ass’y.
Rear Cabinet Ass'y
9
AC Cord Cover Ass'y 2
1
6
4
8
Stand Cover 3
Stand Ass'y 5
4–6
7
LC-40/46/52/60LE810UN (1st Edition)
2. Removing of Speaker-L/R.
1. Remove the 1 lock screw
and detach the Stand cover
.
2. Disconnect SP wire.
3. Detach the Speaker-L
, Speaker-R
.
MAIN Unit
[SP]
[SP]
Speaker-R 4
3 Speaker-L
2 Stand Cover
1
4–7
LC-40/46/52/60LE810UN (1st Edition)
3. Removing of LCD Panel Module, TOUCH SENSOR Unit, ICON Unit, R/C, LED Unit, Front Cabinet Ass’y.
1. Remove the 1 lock screw
and detach the LCD Fixing Metal Angle B-R
2. Remove the 5 lock screws
, 5 lock screws
.
, 4 Hooks and detach the LCD Panel Module
3. Disconnect RA wire.
4. Detach the Touch Sensor Unit
5. Detach the ICON Unit
.
.
6. Detach the R/C, LED Unit
.
3
5 LCD Panel
Module
4
4
3
4
[RA]
3
3
Front Cabinet Ass'y
Hook
Hook
Hook
R/C, 8 [RA]
[RK]
LED Unit
Hook
[RI]
7 ICON Unit
6 TOUCH SENSOR Unit
4–8
LCD Fixing
2 Metal Angle
B-R
1
LC-40/46/52/60LE810UN (1st Edition)
4. Removing of Connectors
1. Disconnect the following connectors from the MAIN Unit. (SB, LB, PD, LW)
2. Disconnect the following connectors from the POWER/ LED DRIVE Unit. (L1, L2, LB, PD, PL)
3. Disconnect the following connectors from the LCD Control Unit. (LW, PL)
POWER/LED DRIVE Unit
MAIN Unit
[LW]
[PL]
LCD Control Unit
POWER/LED DRIVE Unit
MAIN Unit
[L1]
[L2]
[LB]
[SB]
[LB]
[PD]
[PD]
[PL]
4–9
[LW]
LC-40/46/52/60LE810UN (1st Edition)
5. Removing of MAIN Unit, POWER/LED DRIVE Unit, Sub Woofer, Stand Angle Ass’y
1. Remove the 7 lock screws
and detach the MAIN Unit
2. Remove the 2 lock screws
and detach the TERMINAL Angle B
.
3. Remove the 2 lock screws
and detach the TERMINAL Angle S
.
4. Remove the 6 lock screws
and detach the POWER/LED DRIVER Unit
5. Remove the 4 lock screws
and detach the Sub Woofer
.
6. Remove the 1 lock screw
and detach the LCD Fixing Metal Angle B-R
7. Remove the 1 lock screw
and detach the LCD Fixing Metal Angle T-L
8. Remove the 1 lock screw
and detach the LCD Fixing Metal Angle B-MA
9. Remove the 1 lock screw
and detach the LCD Fixing Metal Angle B-L
10.Remove the 1 lock screw
and detach the LCD Fixing Metal Angle B-MB
11.Remove the 6 lock screws
and detach the Stand Angle Ass’y
LCD Fixing 14
Metal Angle T-L
.
.
.
.
.
.
.
11
13
LCD Fixing
12 Metal Angle T-R
1
7
2 MAIN Unit
5
9
10
SUB
Woofer
8 POWER/
LED DRIVE
Unit
[SB]
6 TERMINAL Angle S
4 TERMINAL Angle B
3
[L1]
[L2]
LCD Panel
Module
22 Stand Angle Ass'y
LCD Fixing Metal 18
Angle B-L
21
17 15
20
19
LCD Fixing Metal
Angle B-MB
16 LCD Fixing Metal Angle B-MA
4 – 10
LC-40/46/52/60LE810UN (1st Edition)
[3] REMOVING OF MAJOR PARTS (LC-52LE810UN)
1. Removing of Stand Unit and Rear Cabinet Ass’y.
1. Remove the 1 lock screw
2. Detach the Stand cover
and detach the AC code cover Ass’y
.
.
3. Remove the 2 lock screws
and detach the Stand Ass’y
4. Remove the 4 lock screws
, 1 lock screw
.
, 4 lock screws
and 18 lock screws
and detach the Rear Cabinet Ass’y.
Rear Cabinet Ass'y
9
9
AC Cord Cover Ass'y 2
1
8
6
4
7
Stand Cover 3
Stand Ass'y 5
4 – 11
LC-40/46/52/60LE810UN (1st Edition)
2. Removing of Speaker-L/R.
1. Remove the 2 lock screws
and detach the Stand cover
.
2. Disconnect SP wire.
3. Detach the Speaker-L
, Speaker-R
.
MAIN Unit
[SP]
[SP]
Speaker-R 4
3 Speaker-L
2 Stand Cover
1
4 – 12
LC-40/46/52/60LE810UN (1st Edition)
3. Removing of LCD Panel Module, TOUCH SENSOR Unit, ICON Unit, R/C, LED Unit, Front Cabinet Ass’y.
1. Remove the 1 lock screw
and detach the LCD Fixing Metal Angle B-R
2. Remove the 5 lock screws
, 6 lock screws
.
, 4 Hooks and detach the LCD Panel Module
3. Disconnect RA wire.
4. Detach the Touch Sensor Unit
5. Detach the ICON Unit
.
.
6. Detach the R/C, LED Unit
.
3
5 LCD Panel
Module
4
3
4
4
[RA]
3
LCD Fixing
Metal Angle
B-R
2
3
1
9 Front Cabinet Ass'y
Hook
Hook
Hook
Hook
[RI]
R/C,
8 [RA]
LED Unit
[RK]
7 ICON Unit
6 TOUCH SENSOR Unit
4 – 13
LC-40/46/52/60LE810UN (1st Edition)
4. Removing of Connectors
1. Disconnect the following connectors from the MAIN Unit. (SB, LB, PD, LW)
2. Disconnect the following connectors from the POWER/ LED DRIVE Unit. (L1, L2, LB, PD, PL)
3. Disconnect the following connectors from the LCD Control Unit. (LW, PL)
POWER/LED DRIVE Unit
MAIN Unit
[LW]
[PL]
LCD Control Unit
POWER/LED DRIVE Unit
MAIN Unit
[SB]
[L1]
[L2]
[LB]
[LB]
[PD]
[PD]
[LW]
[PL]
4 – 14
LC-40/46/52/60LE810UN (1st Edition)
5. Removing of MAIN Unit, POWER/LED DRIVE Unit, Sub Woofer, Stand Angle Ass’y
1. Remove the 7 lock screws
and detach the MAIN Unit
2. Remove the 2 lock screws
and detach the TERMINAL Angle B
.
3. Remove the 2 lock screws
and detach the TERMINAL Angle S
.
4. Remove the 6 lock screws
and detach the POWER/LED DRIVER Unit
5. Remove the 4 lock screws
and detach the Sub Woofer
.
6. Remove the 1 lock screw
and detach the LCD Fixing Metal Angle B-R
7. Remove the 1 lock screw
and detach the LCD Fixing Metal Angle T-L
8. Remove the 1 lock screw
and detach the LCD Fixing Metal Angle B-MA
9. Remove the 1 lock screw
and detach the LCD Fixing Metal Angle B-L
10.Remove the 1 lock screw
and detach the LCD Fixing Metal Angle B-MB
11.Remove the 6 lock screws
.
and detach the Stand Angle Ass’y
.
.
.
.
.
.
11
13
LCD Fixing 14
Metal Angle T-L
LCD Fixing
12 Metal Angle T-R
1
2 MAIN Unit
7
5
6 TERMINAL Angle S
9
10
8
SUB
Woofer
[SB]
4 TERMINAL Angle B
POWER/
LED DRIVE
Unit
3
[L1]
[L2]
LCD Panel
Module
LCD Fixing Metal 18
Angle B-L
17
15
16
22
Stand
Angle
Ass'y
LCD Fixing
Metal Angle B-MA
4 – 15
21
20 LCD Fixing Metal
Angle B-MB
19
LC-40/46/52/60LE810UN (1st Edition)
[4] REMOVING OF MAJOR PARTS (LC-60LE810UN)
1. Removing of Stand Unit and Rear Cabinet Ass’y.
1. Remove the 1 lock screw
and detach the AC code cover Ass’y
2. Remove the 3 lock screws
and detach the Support Cover
3. Remove the 4 lock screws
and detach the Stand Ass’y
4. Remove the 4 lock screws
, 1 lock screw
.
.
.
, 5 lock screws
and 18 lock screws
and detach the Rear Cabinet Ass’y.
Rear Cabinet Ass'y
10
10
7
AC Cord Cover Ass'y 2
1
Support Cover 4
3
9
5
8
Stand Ass'y 6
4 – 16
LC-40/46/52/60LE810UN (1st Edition)
2. Removing of Speaker-L/R.
1. Remove the 2 lock screws
and detach the Stand cover
.
2. Disconnect SP wire.
3. Detach the Speaker-L
, Speaker-R
.
MAIN Unit
[SP]
[SP]
Speaker-R 4
3 Speaker-L
2 Stand Cover
1
4 – 17
LC-40/46/52/60LE810UN (1st Edition)
3. Removing of LCD Panel Module, TOUCH SENSOR Unit, ICON Unit, R/C, LED Unit, Front Cabinet Ass’y.
1. Remove the 1 lock screw
and detach the LCD Fixing Metal Angle B-R
2. Remove the 4 lock screws
and detach the 2 Stand Angle
3. Remove the 2 lock screws
, 4 lock screws
.
and detach the 4 Fixing Metal Angle B-MA
4. Remove the 1 lock screw
and detach the LCD Fixing Metal Angle B-L
5. Remove the 1 lock screw
and 1 lock screw
6. Remove the 1 lock screw
and 1 lock screw
7. Remove the 9 lock screws
.
.
and detach the LCD Fixing Metal Angle T-R
and detach the LCD Fixing Metal Angle T-R
and detach the LCD Panel Module
.
.
.
.
8. Disconnect RA wire.
9. Detach the Touch Sensor Unit
10.Detach the ICON Unit
.
.
11.Detach the R/C, LED Unit
.
15
LCD
13
Fixing Metal
Angle B-L
15
11
16
10
17 LCD Panel
Module
LCD Fixing Metal
12 Angle T-R
16
16
[RA]
LCD Fixing
Metal Angle B-L
9
Stand
Angle
8
5
7
4
4 Stand
Angle
2 LCD Fixing
Metal Angle B-R
6
3
3
6
6
5
LCD Fixing
Metal Angle B-MA
Hook
Hook
Hook
Hook
[RI]
[RA]
[RK]
1
LCD Fixing
Metal Angle B-MA
21 Front Cabinet Ass'y
R/C,
LED Unit 20
7
19 ICON Unit
19 TOUCH SENSOR Unit
4 – 18
LC-40/46/52/60LE810UN (1st Edition)
4. Removing of Connectors
1. Disconnect the following connectors from the MAIN Unit. (SB, LB, PD, LW)
2. Disconnect the following connectors from the POWER/ LED DRIVE Unit. (L1, L2, LB, PD, PL)
3. Disconnect the following connectors from the LCD Control Unit. (LW, PL)
POWER/LED DRIVE Unit
MAIN Unit
[LW]
[PL]
LCD Control Unit
POWER/LED DRIVE Unit
[L1]
[L2]
[LB]
[PD]
MAIN Unit
[SB]
[LB]
[PD]
[LW]
[PL]
4 – 19
LC-40/46/52/60LE810UN (1st Edition)
5. Removing of MAIN Unit, POWER/LED DRIVE Unit, Sub Woofer, Stand Angle Ass’y
1. Remove the 7 lock screws
and detach the MAIN Unit
2. Remove the 2 lock screws
and detach the TERMINAL Angle B
.
3. Remove the 2 lock screws
and detach the TERMINAL Angle S
.
4. Remove the 6 lock screws
and detach the POWER/LED DRIVER Unit
5. Remove the 4 lock screws
and detach the Sub Woofer
.
.
1
2 MAIN Unit
5
9
6 TERMINAL Angle S
[SB]
10
4 TERMINAL Angle B
SUB
Woofer
3
[L1]
[L2]
LCD Panel
Module
7
8 POWER/LED
DRIVE
Unit
4 – 20
LC-40/46/52/60LE810UN (1st Edition)
CHAPTER 5. ADJUSTMENT
LC-40LE810UN
Service Manual
[1] ADJUSTMENT PROCEDURE
The adjustment values are set to the optimum conditions at the factory before shipping. If a value should become improper or an adjustment is
required due to part replacement, make an adjustment according to the following procedure.
1. After replacement of any PWB unit and/or IC for repair, please note the following.
• When replacing the following units, make sure to prepare the new units loaded with updated software.
MAIN Unit:
DKEYMF452FM01
• When replacing the LCD control PWB, perform the VCOM adjustment.
2. Upgrading of each microprocessor software
CAUTION: Never “POWER OFF” the unit when software upgrade is ongoing.
Otherwise the system may be damaged beyond recovery.
2.1. Software version upgrade
The model employs the following software.
•
Main software (please use a software version after HLNRBxxx.USB (32” HLNRCxxx.USB).)
•
Monitor microprocessor software (please use a software version after HLNRA0x.USB and HLNIMxxx.BIN.)
The main software, monitor microprocessor software can be upgraded by using a general-purpose USB Memory.
The followings are the procedures for upgrading, explained separately for the main software, monitor microprocessor software.
2.2. Main software version upgrade
2.2.1 Get ready before you start
•
USB Memory of 128MB or higher capacity.
•
PC running on Windows 98/98SE/ME/2000/XP operating system.
•
USB Memory reader/writer or PC with a USB port.
•
The file system of a USB memory is FAT. (FAT32 supports)
•
Use the USB memory without other functions. (lock and memory reader...etc)
2.2.2 Preparations
To upgrade the main software, it is necessary to get ready the USB Memory for version upgrade before you start.
Follow the steps below and create the USB Memory for version upgrade.
1. Copy the file HLNRBxxx.USB (32” HLNRCxxx.USB). for version upgrade to the root directory (folder) of the USB Memory.
NOTE: In the USB Memory drive, do not store other folders or unrelated files, or more than one file for version upgrade.
Now the USB Memory for version upgrade is ready.
5–1
LC-40/46/52/60LE810UN (1st Edition)
2.2.3 How to upgrade the software
1. Plug AC cord and turn on the TV.
2. After picture displayed, touch the power key for 5seconds.
NOTE: Picture will disappear when you touch the power key, but keep touching it.
3. When the center icon LED blinks, release your finger from the power key.
4. Next, touch the “POWER” and “CH (
)” keys at the same time.
5. When the center icon LED turns on, release your finger form the keys.
6. After the unit startup, the system upgrade screen as shown below within 20-40 seconds.
LE810UN
7. Even a single failure in the process will trigger the upgrade failure screen.
LE810UN
NOTE: In the event of a failure, repeat the upgrade process. If the process repeatedly fails, it is likely that the hardware need fixing.
8. Upon completion of the whole process, the upgrade success screen as shown below appears. You can check the new software version on this
screen. The version information appears after the upgrade is complete.
LE810UN
9. Unplug the AC cord and remove the USB Memory for version upgrade.
10.Now the software version upgrade is complete.
NOTE: When you are done with the software version upgrade, start the set, go to the top page of the adjustment process screen and check the main
software version information.
5–2
LC-40/46/52/60LE810UN (1st Edition)
2.3. Monitor microprocessor software version upgrade
Create the USB memory for monitor microprocessor software version upgrade in the same manner as explained in the “Main software version
upgrade”.
Copy the file HLNRVA0x.USB and HLNIMxxx.BIN (named temporarily) for monitor microprocessor software version upgrade to the USB memory.
2.3.1 How to upgrade the software
1. Plug AC cord and turn on the TV.
2. After picture displayed, touch the power key for 5seconds.
NOTE: Picture will disappear when you touch the power key, but keep touching it.
3. When the center icon LED blinks, release your finger from the power key.
4. Next, touch the “POWER” and “CH (
)” keys at the same time.
5. When the center icon LED turns on, release your finger form the keys.
CAUTION: •
•
The moment this operation is done, the upgrading of the monitor microprocessor software starts. While the upgrade is ongoing, never
power off the unit. Otherwise the upgrade will fail and the system may be serious damaged beyond recovery (inability to start).
After the monitor microprocessor software is upgraded, also perform the 'Industry Init'.
6. After the unit startup, the upgrade starts. The power led will blink continuously. Also, an upgrade screen will be shown during a minor upgrade.
LE810UN
7. If the upgrade fails, power led will stop blinking. Also, the upgrade failure screen will be shown if upgrade screen was shown at 5.
LE810UN
NOTE: In the event of a transient failure, upgrade will be automatically retried up to three times. If the process repeatedly fails, hardware may be the
cause.
8. Up on completion of the whole process, power and OPC LED will blink alternately. Also, the upgrade success screen will be shown if upgrade
screen was shown at 5.
LE810UN
9. Unplug the AC cord and remove the USB Memory for version upgrade.
10.Now the software version upgrade is complete.
NOTE: When you are done with the software version upgrade, start the set, go to the top page of the adjustment process screen and check the monitor microprocessor software version information and panel size information.
5–3
LC-40/46/52/60LE810UN (1st Edition)
3. Entering and exiting the adjustment process mode
1) Before entering the adjustment process mode, the AV position RESET in the video adjustment menu.
2) At the state TV is turned on, touch the power key for 5seconds.
NOTE: Picture will disappear when you touch the power key, but keep touching the power key.
3) When the center icon LED blinks, release your finger from the power key.
4) Next, touch the power key with “VOL (-)” and “INPUT” keys at the same time.
TV will turn on and the letter “<K>” appears on the screen.
5) Next, touch the “VOL (—)” and “CH (
)” keys at the same time.
6) When the center icon LED turns on, release your finger form the keys.
(The “VOL (—)” and “CH (
)” keys should be pressed and held until the display appears.)
Multiple lines of blue characters appearing on the display indicate that the unit is now in the adjustment process mode.
When you fail to enter the adjustment process mode (the display is the same as normal startup), retry the procedure.
7) To exit the adjustment process mode after the adjustment is done, unplug the AC cord from the outlet to make a forced shutdown. (When the
power was turned off with the remote controller, once unplug the AC cord and plug it again. In this case, wait 10 seconds or so before plugging.)
CAUTION: Use due care in handling the information described here lest your users should know how to enter the adjustment process mode. If the
settings are tampered in this mode, unrecoverable system damage may result.
4. Remote controller key operation and description of display in adjustment process mode
1) Key operation
Remote controller key
CH (
/
)
VOL (+/–)
Cursor (UP/DOWN)
Cursor (LEFT/RIGHT)
INPUT
ENTER
Main unit key
Function
Moving an item (line) by one (UP/DOWN)
CH (
/
)
VOL (+/–)
—————
—————
—————
—————
Changing a selected item setting (+1/ –1)
Turing a page (PREVIOUS/NEXT)
Changing a selected line setting (+10/ –10)
Input switching (toggle switching)
Executing a function
*Input mode is switched automatically when relevant adjustment is started so far as the necessary input signal is available.
2) Description of display
(1) Current page/
Total pages
(2) Current selected input
(3) Current color system
(5) LCD Panel size/Speaker type
(4) Destination
1/24
MAIN Version
INPUT5
AUTO
BOOT Version
HLNI 100
Monitor/Monitor BOOT Version
1.02/1.00
LCD Con Version
0900626000T0001
LED TCON Version
16
EQ DATA CHECKSUM
ROM
TEMPERATURE
7B
LAMP ERROR
USA
40_UNDER
1.09 (U 2009/07/07 1A)
(6) Adjustment
process menu
header
(7) Parameters
0
MONITOR ERR CAUSE
0
NORMAL STANDBY CAUSE
0
ERROR STANDBY CAUSE
1)
0
4)
0
0H 0M
0H 0M
2)
0
5)
0
5–4
0H 0M
0H 0M
3)
0
0H 0M
LC-40/46/52/60LE810UN (1st Edition)
5. List of adjustment process mode menu
The character string in brackets [ ] will appear as a page title in the adjustment process menu header.
Page
1
2
3
4
5
6
Line
1
2
3
4
5
6
7
8
9
10
11
12
13
1
2
3
4
5
6
7
8
9
10
11
12
13
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
1
2
3
4
5
6
7
1
2
3
4
5
6
7
Item
MAIN Version
BOOT Version
Monitor/Monitor BOOT Version
LCD CON Version / LED CON Version
Netflix ESN
FRC-N Auto Script Version
TCON Master/Slave Serial Version
TOUCH SENSOR UCON VERSION
TEMPERATURE
LAMP ERROR
MONITOR ERR CAUSE
NORMAL STANDBY CAUSE
ERROR STANDBY CAUSE
INDUSTRY INIT
INDUSTRY INIT(-Hotel)
PUBLIC MODE
Center Acutime
RESET
Backlight Acutime
RESET
LAMP ERROR RESET
VIC XPOS
VIC YPOS
VIC COLOR
VIC SIGNAL TYPE
VIC READ
N358 ALL ADJ(INPUT1)
N358 MAIN ADJ(INPUT1)
TUNER DAC ADJ
N358 CONTRAST A_GAIN
N358 CONTRAST D_GAIN
N358 CONTRAST OFFSET
TUNER CONTRAST A_GAIN
TUNER CONTRAST D_GAIN
TUNER CONTRAST OFFSET
TUNER VCHIP TEST(69ch)
TUNER VCHIP TEST(7ch)
TUNER VCHIP TEST(10ch)
TUNER VCHIP TEST(15ch)
INSPECT USB TERM
HDMI EDID WRITE
HDMI CEC TEST
COMP15K ADJ(INPUT1)
COMP15K Y A_GAIN
COMP15K Cb A_GAIN
COMP15K Cr A_GAIN
COMP15K Y OFFSET
COMP15K Cb OFFSET
COMP15K Cr OFFSET
COMP33K ADJ(INPUT1)
COMP33K Y A_GAIN
COMP33K Cb A_GAIN
COMP33K Cr A_GAIN
COMP33K Y OFFSET
COMP33K Cb OFFSET
COMP33K Cr OFFSET
Description
Main software version
Remarks (adjustment detail, etc.)
Monitor and monitor boot software version
LCD controller software version
Versions are always ‘090626000T0001’.
Audio data checksum
Panel temperature
Number of termination due to lamp error
Refer to *1 under the list for details
Refer to *2 under the list for details
Initialization to factory settings
Public mode
Accumulated main operation time
Reset
Accumulated monitor operation time
Reset
Reset LAMP ERROR
X-coordinate setting for VIC READ
Y-coordinate setting for VIC READ
Collected color data setting for VIC READ
Signal type setting for VIC READ
Picture level acquisition function
CVBS and TUNER signal level adjustment
CVBS signal level adjustment
TUNER signal level adjustment
Tuning test and VCHIP test (69ch)
Tuning test and VCHIP test (7ch)
Tuning test and VCHIP test (10ch)
Tuning test and VCHIP test (15ch)
Component 15K picture level adjustment (main)
Component 33K picture level adjustment (main)
5–5
Level appears in green on the upper right
LC-40/46/52/60LE810UN (1st Edition)
Page
7
8
9
10
11
12
13
Line
1
2
3
4
5
6
7
1
1
2
3
4
5
6
1
2
3
4
5
6
7
8
9
10
11
12
1
2
3
4
5
6
7
8
9
10
11
12
13
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
Item
ANALOG RGB ADJ
R A_GAIN
G A_GAIN
B A_GAIN
R OFFSET
G OFFSET
B OFFSET
VCOM ADJ
LEV1
LEV2
LEV3
LEV4
LEV5
LEV6
MG1R
MG1G
MG1B
MG1Y
MG2R
MG2G
MG2B
MG2Y
MG3R
MG3G
MG3B
MG3Y
MG4R
MG4G
MG4B
MG4Y
MG5R
MG5G
MG5B
MG5Y
MG6R
MG6G
MG6B
MG6Y
MG6Y OFFSET
MODE SELECT
POS SELECT
POS MIN
POS MID1
POS MID2
POS MID3
POS MID4
POS MID5
POS MID6
POS MAX
CD MIN
CD MID1
CD MID2
CD MID3
CD MID4
CD MID5
CD MID6
CD MAX
Description
Analog RGB picture level adjustment
VCOM adjustment value
Standard value 1
Standard value 2
Standard value 3
Standard value 4
Standard value 5
Standard value 6
WB adjustment Point 1, R adjustment value
WB adjustment Point 1, G adjustment value
WB adjustment Point 1, B adjustment value
WB adjustment Point 1, Y adjustment value
WB adjustment Point 2, R adjustment value
WB adjustment Point 2, G adjustment value
WB adjustment Point 2, B adjustment value
WB adjustment Point 2, Y adjustment value
WB adjustment Point 3, R adjustment value
WB adjustment Point 3, G adjustment value
WB adjustment Point 3, B adjustment value
WB adjustment Point 3, Y adjustment value
WB adjustment Point 4, R adjustment value
WB adjustment Point 4, G adjustment value
WB adjustment Point 4, B adjustment value
WB adjustment Point 4, Y adjustment value
WB adjustment Point 5, R adjustment value
WB adjustment Point 5, G adjustment value
WB adjustment Point 5, B adjustment value
WB adjustment Point 5, Y adjustment value
WB adjustment Point 6, R adjustment value
WB adjustment Point 6, G adjustment value
WB adjustment Point 6, B adjustment value
WB adjustment Point 6, Y adjustment value
5–6
Remarks (adjustment detail, etc.)
Adjustment gradation setting.
Parameter for six-point adjustment
Parameter for six-point adjustment
LC-40/46/52/60LE810UN (1st Edition)
Page
14
15
16
17
18
19
20
21
22
Line
1
2
3
4
5
6
7
8
1
2
3
1
2
3
4
5
6
7
1
2
3
4
5
6
7
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
1
2
3
4
5
6
7
8
1
2
3
4
5
6
Item
CALC
RESET
VAL1
VAL2
VAL3
VAL4
VAL5
VAL6
MONITOR TIME OUT
MONITOR MAX TEMP
MONITOR ERROR CAUSE RESET
LCD TEST PATTERN
LCD TEST PATTERN1
LCD TEST PATTERN2
LCD TEST PATTERN3
LCD TEST PATTERN4
TV TEST PATTERN 1
TV TEST PATTERN 2
FRC-N Firmware Version
FRC-N Boot Script Version
FRC-N Device Version
TCON FPGA1 Serial Flash Version
TCON FPGA2 Serial Flash Version
TCON FPGA1 Config Rom Version
TCON FPGA2 Config Rom Version
READ/WRITE
SLAVE ADDRESS
RESISTER ADDRESS UPPER
RESISTER ADDRESS LOWER
WRITE DATA UPPER
WRITE DATA LOWER
READ DATA UPPER
READ DATA LOWER
POWER LED BRIGHTNESS
MENU LED BRIGHTNESS
INPUT LED BRIGHTNESS
CH UP LED BRIGHTNESS
CH DOWN LED BRIGHTNESS
VOL UP LED BRIGHTNESS
VOL DOWN LED BRIGHTNESS
LOGO LED BRIGHTNESS
ICON LED BRIGHTNESS
ICON LED BRIGHTNESS
(STANDBY)
POWER KEY SENSITIVITY
MENU KEY SENSITIVITY
INPUT KEY SENSITIVITY
CH UP KEY SENSITIVITY
CH DOWN KEY SENSITIVITY
VOL UP KEY SENSITIVITY
VOL DOWN KEY SENSITIVITY
KEY STRENGTH GET MODE
POWER KEY STRENGTH
MENU KEY STRENGTH
INPUT KEY STRENGTH
CH UP KEY STRENGTH
CH DOWN KEY STRENGTH
VOL UP KEY STRENGTH
VOL DOWN KEY STRENGTH
KEY LOCK (1217)
KOUTEI AREA ALL CLEAR
A MODE AREA CLEAR
BACKUP AREA CLEAR
B MODE AREA CLEAR
EXECUTION
Description
5–7
Remarks (adjustment detail, etc.)
LC-40/46/52/60LE810UN (1st Edition)
Page
23
24
Line
1
2
3
4
5
6
1
2
3
4
5
6
7
8
9
10
Item
ERROR STANDBY CAUSE1
ERROR STANDBY CAUSE2
ERROR STANDBY CAUSE3
ERROR STANDBY CAUSE4
ERROR STANDBY CAUSE5
ERROR STANDBY CAUSE RESET
EEP SAVE
EEP RECOVER
MODL NAME
PANEL SIZE
SETTING FOR ADJ
PANEL LIMIT
PANEL RANGE LIMIT
SHORT CHECK MODE
SHORT CHECK CURRENT
CURRENT SW
Description
Writing setting values to EEPROM
Reading setting values from EEPROM
*1 Details of P1.9 (NORMAL STANDBY CAUSE)
2
No operation off
3
No signal off
4
PC power management mode 1
5
PC power management mode 2
6
Off timer
8
Command from RS232C
in the cause of “no operation off”
in the cause of “no signal off”
in the cause of “Standby mode MODE1”
in the cause of “Standby mode MODE2”
in the cause of “SLEEP timer”
in the cause of command by RS-232C
*2 Details of P1.10 (ERROR STANDBY CAUSE)
11 Prolonged unspecified-signal input in PC mode
17 Temperature error
1A Monitor trouble detected
22 LCD controller Rom error
in the cause of continuous “out of range”, PC input mode
in the cause of abnormal temperature
in the cause of abnormal monitor mode
in the cause of software abnormality of LCD controller
6. Special features
*
STANDBY CAUSE (Page 1/24)
Display of a cause (code) of the last standby
The cause of the last standby is recorded in EEPROM whenever possible.
Checking this code will be useful in finding a problem when you repair the troubled set.
*
EEP SAVE (Page 24/24)
Storage of EEP adjustment value
*
Remarks (adjustment detail, etc.)
EEP RECOVER (Page 24/24)
Retrieval of EEP adjustment value from storage area
5–8
LC-40/46/52/60LE810UN (1st Edition)
7. Microcomputer software writing
7.1. Main microcomputer/monitor microcomputer software writing (Main PWB: QPWBXF452WJZZ)
1
Adjustment item
Main microcomputer/monitor microcomputer software
writing
<Main PWB>
Adjustment conditions
Checker process
Adjustment procedure
1. Connect the specified writing jig to SC8452 (TL8461-8475) via the checker.
2. Connect the USB memory to J3301 (TL3309-3312) or J3302 (TL3332-3335)
via the checker.
3. Apply the specified voltage to the PWB and perform boot from the jig.
4. Send the software writing start command via RS232C.
5. Send the writing status check command and confirm the response of OK. Then
turn off the power.
File version check
USB memory check
CAUTION: When the USB memory is not inserted or reading error occurs, nothing
is written.
7.2. Model/inch discrimination writing (Main PWB: QPWBXF452WJZZ)
•
Refer to the production precautions.
8. Signal adjustment
8.1. LCD section adjustment [LCD module adjustment]
1
Adjustment item
Opposite bias adjustment
(LCD module adjustment
item)
Adjustment conditions
Adjustment in the center
position of the panel
Adjustment procedure
1. Enter the process mode using the process adjustment remote control.
2. Select [VCOM ADJ] using the Channel
/
keys on the remote control.
3. Press the Enter key to check that the pattern for adjustment is displayed.
4. Make adjustment so that the flicker located in the center of the screen is minimized using the Volume +/- keys on the remote control.
5. If the optimum condition is obtained in step 4, press the Enter key to turn off the
pattern.
CAUTION: * Make adjustment with no ANT signal (since the brightness is
changed by the active backlight).
[Adjustment position]
1/4
3/4
1/2
1/2
8.2. Image adjustment
8.2.1 Device check
Before adjustment, check that the adjustment jig and signal source are set for Sharp LCD US.
Signal generator level adjustment check (Adjust to the standard value level.)
•Composite signal:
•15K component signal:
•33K component signal:
•Analog RGB:
Y level:
PB/PR level:
Y level:
PB/PR level:
RGB level:
0.714Vp-p ± 0.02Vp-p (Pedestal to white)
0.714Vp-p± 0.02Vp-p (Pedestal to white)
0.7Vp-p ± 0.02Vp-p
0.7Vp-p ± 0.02Vp-p (Pedestal to white)
0.7Vp-p ± 0.02Vp-p
0.7Vp-p ± 0.02Vp-p (Pedestal to white)
8.2.2 Process mode
Adjustment point
Process mode
Adjustment conditions
Adjustment procedure
Enter the process adjustment mode using the process adjustment remote control.
5–9
LC-40/46/52/60LE810UN (1st Edition)
8.2.3 Composite N358 signal/tuner adjustment
1
Adjustment point
Setting
Adjustment conditions
N358 signal
US-10ch
Adjustment procedure
•Send the N358 color bar (color saturation: 75%) signal to the Video 2 video input.
•Send the in-house signal (use US-10ch) to TUNER.
[Video input signal]
[In-house US-10ch]
Color saturation: 75%
100% white
2
Automatic adjustment execution
0% black
100% white
Point the cursor to [ N358 ALL ADJ(INPUT2)] and press the [Enter] key.
The adjustment is complete when [ N358 ALL ADJ(INPUT2) OK] is displayed.
8.2.4 Component 15K signal adjustment
1
Adjustment point
Setting
Adjustment conditions
480i signal
Adjustment procedure
•Send the 100% color bar signal to the Video 1 component input.
Color saturation: 100%
100% white
2
Automatic adjustment execution
480i
100% color bar
0% black
Point the cursor to [ COMP15K ADJ(INPUT1)] and press the [Enter] key.
The adjustment is complete when [ COMP15K ADJ(INPUT1) OK] is displayed.
8.2.5 COMPONENT 33K signal adjustment
1
Adjustment point
Setting
Adjustment conditions
1080i signal
Adjustment procedure
•Send the 100% color bar signal to the Video 1 component input.
Color saturation: 100%
100% white
2
Automatic adjustment execution
1080i
100% color bar
0% black
Point the cursor to [ COMP33K ADJ(INPUT1)] and press the [Enter] key.
The adjustment is complete when [ COMP33K ADJ(INPUT1) OK] is displayed.
8.2.6 Analog RGB signal adjustment
1
Adjustment point
Setting
Adjustment conditions
Signal: XGA
(1024x768) 60Hz
SYNC: HV separate
Adjustment procedure
•Send the 100% color bar signal to the Video 4 analog RGB input.
XGA (1024x768)
100% color bar
100% white
2
Automatic adjustment execution
0% black
Point the cursor to [ ANALOG RGB ADJ] and press the [Enter] key.
The adjustment is complete when [ ANALOG RGB ADJ OK] is displayed.
5 – 10
LC-40/46/52/60LE810UN (1st Edition)
8.2.7 Tuner/V-CHIP adjustment
1
2
Adjustment point
Setting
Automatic adjustment execution
Adjustment conditions
NTSC RF signal
US-7(AIR)ch
Adjustment procedure
•Send the NTSC signal to the RF antenna input.
Point the cursor to [ TUNER VCHIP TEST(*07ch)] and press the [Enter] key. (*
Adjust the selected channel to the in-house signal.)
The adjustment is OK when [ A-OK(***.**)/VM-OK] is displayed in green.
(NG when A-NG/VM-NG is displayed in red.)
It is OK when the deviation from the center frequency is ±0.0625MHz or less.
5 – 11
LC-40/46/52/60LE810UN (1st Edition)
9. White balance adjustment
9.1. White balance adjustment (For details about the adjustment procedure, refer to “Kameyama Model Integrated Monitor
WB Adjustment Specification V1.92”.)
1
2
Adjustment
point
Setting
Automatic
adjustment execution
Adjustment conditions
[Command]
Process mode
KRSW0001
KKT10037
Setting
KY0F0000
0SDS0001
SBSL0016
Multi-point adjustment mode
MSET0011
Point 6
LEV60229
MG6G****
MG6B****
MG6R****
MG6Y****
Point 5
LEV50173
MG5G****
MG5B****
MG5R****
MG5Y****
Point 4
LEV40133
MG4G****
MG4B****
MG4R****
MG4Y****
Point 3
LEV30116
MG3G****
MG3B****
MG3R****
MG3Y****
Adjustment procedure
1) Set the unit to the following conditions.
AV MODE: [DYNAMIC]
Backlight: +16
Active Backlight: OFF
Aging Time: Min. 60 minutes
2) Connect the unit with the white balance adjustment jig.
[Adjustment procedure]
1) Send the “adjustment process” code using the remote control.
2) Set the point 6 to the specified gradation, specify the strongest color as the fixed
color, and adjust the RGB so that it becomes the standard value through negative
adjustment. Then compare the R and G values; based on the result, calculate the Ye
value in the following conditions.
R > G: Ye = G x 1.05
R G: Ye = R x 1.05
* If the Ye value exceeds the initial value (input gradation x 4), it is rounded to that
value or less.
3) Set the point 5 to the specified gradation, set the G correction value (692 x G value of
point 6/916) (fractions rounded off) and the Ye correction value (692 x Ye value of
point 6/916) (fractions rounded off), and adjust the RB so that it becomes the standard value.
4) Set the point 4 to the specified gradation, set the G correction value (532 x G value of
point 6/916) (fractions rounded off) and the Ye correction value (532 x Ye value of
point 6/916) (fractions rounded off), and adjust the RB so that it becomes the standard value.
5) Set the point 3 to the specified gradation, set the G correction value (464 x G value of
point 6/916) (fractions rounded off) and the Ye correction value (464 x Ye value of
point 6/916) (fractions rounded off), and adjust the RB so that it becomes the standard value.
6) Set the point 2 to the specified gradation, set the G correction value (296 x G value of
point 6/916) (fractions rounded off) and the Ye correction value (296 x Ye value of
point 6/916) (fractions rounded off), and adjust the RB pattern so that it becomes the
standard value.
7) Set the point 1 to the specified gradation, set the G correction value (180 x G value of
point 6/916) (fractions rounded off) and the Ye correction value (180 x Ye value of
point 6/916) (fractions rounded off), and adjust the RB so that it becomes the standard value.
8) Write the adjustment value by the MSET0003 command and turn off the AC power.
* RGB initial value of point 6: Set gradation 916
* RGB initial value of points 1 to 5: G correction value of each point
(At each point, make adjustment so that the remainder of the RGB adjustment value/
4 is equal.)
[Adjustment value]
* According to the “Standard settings” submitted by the Technical Department
[LC52LE810UN] LE810 model teaching set
Point 2
LEV20074
MG2G****
MG2B****
MG2R****
MG2Y****
Point 1
LEV10045
MG1G****
MG1B****
MG1R****
MG1Y****
Writing
MSET0003
5 – 12
LC-40/46/52/60LE810UN (1st Edition)
Adjustment
point
Adjustment conditions
Adjustment procedure
[Adjustment standard value]
Measuring instrument: [Minolta CA-210] Technical measuring instrument
Level
Reference value
Adjustment spec
Inspection spec
X=0.272
Point 6
916
±0.0010
±0.0020
y=0.277
X=0.272
Point 5
692
±0.0010
±0.0020
y=0.277
X=0.272
Point 4
532
±0.0015
±0.0030
y=0.277
X=0.272
Point 3
464
±0.0020
±0.0040
y=0.277
X=0.272
Point 2
296
±0.0030
±0.0060
y=0.277
X=0.272
Point 1
180
±0.004
±0.0080
y=0.277
Remarks
Setting conditions for inspection
AV MODE: [DYNAMIC] (Reset)
Monochro: ON
Active Backlight: OFF
Aging Time: Min. 60 minutes
10. Key writing
10.1. EDID writing (Main PWB: QPWBXF452WJZZ)
1
2
Adjustment point
HDMI EDID writing
(Main PWB)
Analog RGB EDID writing
(Main PWB)
Adjustment conditions
Process mode
Model discrimination check
Adjustment procedure
1) Enter the process mode.
2) Point the cursor to [EDID WRITE ENT] and press the [ENT] key.
The writing is complete when [EDID WRITE OK] is displayed.
(If not written, HDMI does not function.)
CAUTION: Perform the data writing after setting the model discrimination. The data based on the model discrimination
information is recorded in EEPROM.
1) Write the EDID data for analog RGB into IC509 mounted on the
main PWB using the checker.
TL511 ••• I2C clock, TL508 ••• I2C data
TL544 ••• 5V, TL507 ••• GND
TL585 ••• Write protection (H: WP, L: write enable)
2) Perform the data writing before making inspection using the
checker.
Inspection mode
File version check
10.2. MMAC address writing (Main PWB: QPWBXF452WJZZ)
1. Refer to the production precautions.
10.3. Netflix & WMDRM Key writing (Main PWB: QPWBXF452WJZZ)
1. Netflix key data is written in IC8401. The data cannot be copied nor run on different CPU. It can be written only in factory securely.
Therefore when key data is corrupted or lost or you replace main CPU, IC8001, or flash ROM, IC8401, you have to replace main PWB.
You can check if the key data is stored correctly by following means.
•
Process menu
•
RS-232C
The key is displayed to [NETFLIX ESN] on the 1st page in the adjustment process menu.
1. Enter the process mode.
2. NFKY???? : ESN Data is returned.
5 – 13
LC-40/46/52/60LE810UN (1st Edition)
11. Factory setting
After completing the factory setting, pull out the AC cord to complete the setting.
CAUTION: Do not turn on the power after completing the factory setting. If the power is turned on, configure the factory setting again.
1
Adjustment point
Factory setting
Adjustment conditions
Complete the setting by
pulling out the AC cord.
Adjustment procedure
•Point the cursor to [INDUSTRY INIT (+Cause)], set to “ON” using [+]/[-] of the [VOL] key,
and press the [ENT] key.
The version confirmation screen appears on the green screen. It is completed when [SUCCESS] is displayed at the top.
(If error occurs, [ERROR] is displayed on the red screen.)
•Turn off the AC power.
The following items are initialized when configuring the factory setting.
1) User set value
2) Channel data (broadcasting frequency, etc.)
3) Password setting value
4) Operating time
5) StandbyCause
6) Auto installation flag
7) V-CHIP block setting value
12. Software version
1. Main microcomputer
2. Monitor microcomputer
3. EDID data (Analog RGB)
4. (Reference: File name in the Technical Department)
For analog RGB Input3: IC509: edid_dsub15_fullhd_v6_256.BIN
13. Writing the inch and model name onto EEPROM
Writing method
1. Pull out the AC cord.
2. Copy the application for writing inch/model name (HLNIMA01.USB) and model/inch file (40LE810.MDL) to the USB memory.
3. Hold down the power button and insert the AC cord.
4. Release the power button after 5 seconds.
5. Update starts.
The inch and model name are displayed.
40LE810
UPGRADE SUCCESS
6. Pull out the AC cord.
Model/inch file
•
40LE810.MDL
•
46LE810.MDL
•
52LE810.MDL
•
60LE810.MDL
*
32 inch is not necessary.
NOTE: When replacing the main PWB, make sure to perform the writing the inch and model name onto EEPROM
5 – 14
LC-40/46/52/60LE810UN (1st Edition)
[2] PUBLIC MODE SETTING PROCEDURE
1. How to start Public Mode
• There are the following 3 ways to get the public mode setup screen displayed.
In the adjustment process mode, turn on “PUBLIC MODE”
1) Plug AC cord and turn on the TV.
2) After picture displayed, touch the “POWER” key for 5seconds.
NOTE: Picture will disappear when you touch the power key, but keep touching it.
3) When the center icon LED blinks, release your finger from the power key.
4) Next, touch the “CH (
)” key and “VOL (+)” keys on the set at the same time.
5) When the center icon LED turns on, release your finger form the keys.
It’s same as
from 1) to 3)
4) Next, touch the “INPUT” key and “CH
” keys on the set at the same time.
5) When the center icon LED turns on, release your finger form the keys.
6) Get the password input screen displayed.
Procedure
˴The input starts with the leftmost digit.
˴Use the numeric keys [1] thru [9] and [0] keys on the remote controller.
˴The other keys are not acceptable.
˴With a numeric-key input, "_" will change to "˴".
˴The input position will move one digit to the right.
˴With all the 3 digits entered, the password will be verified.
7) The 3-digit password is now verified.
The password [0] [2] [7] provides for the public mode screen. (This screen comes on with whatever adjustment process settings.)
With any other passwords, the screen changes to the normal mode.
2. How to exit Public Mode
There are the following ways to quit the public mode setup screen.
• Turn off “PUBLIC MODE” in the adjustment process mode. (
• Turn off the power with the “POWER” key. (
• Select “EXECUTE”. (
) ← This way alone is not for quitting the setup screen, but for quitting the mode itself.
)
)
... “PUBLIC MODE” stays on in the adjustment process mode.
... The settings will be back to the factory ones.
3. Public Mode Setting Values
• With the factory settings made, the public mode settings get initialized. (The adjustment process remains intact.)
5 – 15
LC-40/46/52/60LE810UN (1st Edition)
4. Public Mode Menu
The guidance is not displayed on screen.
Setup procedure
• To move the cursor up and down, use the “cursor UP/DOWN” key (remote controller) and “CH (
)/(
)” key (remote controller and set).
• To change the settings, use the “cursor RIGHT/LEFT” key (remote controller) and “VOL (+)/(–)” key (remote controller and set).
• To save new settings, keep the cursor at “EXECUTE” and use “ENTER” key (remote controller and set).
PUBLIC MODE
POWER ON FIXED
[VARIABLE ]
MAXIMUM VOLUME
[
VOLUME FIXED
[VARIABLE ]
VOLUME FIXED LEVEL
[
RC BUTTON
[RESPOND ]
PANEL BUTTON
[RESPOND ]
MENU BUTTON
[RESPOND ]
AV POSITION FIXED
[VARIABLE ]
ON SCREEN DISPLAY
[YES
]
INPUT MODE START
[NORMAL
]
INPUT MODE FIXED
[VARIABLE ]
LOUD SPEAKER
[ON
]
RC_PATH_THROUGH
[OFF
]
232C POWON
[DISABLE
]
PUBLIC MODE
[OFF
]
60 ]
20 ]
RESET
EXECUTE
5 – 16
LC-40/46/52/60LE810UN (1st Edition)
5. On Setting Items
* “EZ-SETUP” discussed below indicates “EZ-SETUP after the first power-on”.
1) POWER ON FIXED
Selection
Default
Explanation
Limit in Setting
Exception
Remarks
Selection between “Variable” and “Fixed” (loop provided)
– (Variable)
In “Fixed” setting, the power-off by the power key of the unit is invalidated and the image is kept being received. The power can
be turned off by stopping the power supply from AC.
Refer to the “Power-On Fixed” sheet.
None
• In “Variable” setting, the power operation is in wait for 1 sec. and then turned off when the main power switch is off.
2) MAXIMUM VOLUME
Selection
Default
Explanation
Limit in Setting
Exception
Remarks
Adjustment from 0 to 60 (no loop)
60
Sound volume can not be adjusted higher than the preset value.
• When the sound volume is set lower than 59, only figures are displayed and the sound volume bar is not displayed.
• The maximum sound volume for ON-timer (Wake up timer) is limited also to the preset value.
• When the sound volume is set higher than the MAX setting by the adjusting process, the sound volume control operation is
prohibited for turn-up and the sound volume should be turned down to MAX in this state.
3) VOLUME FIXED
Selection
Default
Explanation
Limit in Setting
Exception
Remarks
Selection between “Variable”, “Fixed”, “ACON (AC CTRL)” and “AC/RCON (AC/RC CTRL)” (loop provided)
Variable
• FIXED: Fixed at the level adjusted for a fixed volume.
• AC CTRL: Start-up at the level specified for a fixed volume at ACON.
• AC/RC CTRL: Start-up at the level specified for a fixed volume at start.
• The sound volume for the ON-timer (Wake up timer) is fixed also without display of menu. Besides, the setting is made
impossible. (Basically, the menu is not displayed.)
• The following keys become invalid:
• Sound volume Up/Down (VOL +/–) [for both remote control and the unit]
• Mute (MUTE)
• In the item “VOLUME” of adjustment process, the sound volume can be set freely irrespective of this setting.
• As for sound volume fixing and sound volume MAX level, the sound volume fixing has priority.
• Once the sound volume has been changed by adjustment process, it should be set back to the sound volume preset by
sound volume fixing level when the adjustment process ends.
4) VOLUME FIXED LEVEL
Selection
Default
Explanation
Limit in Setting
Exception
Remarks
Adjustment from 1 to 60 (no loop)
20
The sound volume to be fixed by “Volume fixed” is determined.
None
None
Setting is valid only when “Volume fixed” is selected for “fixed”.
5) RC BUTTON
Selection
Default
Explanation
Selection between “Respond”, “No Respond” and “Limited” (loop provided)
Respond
Making the remote controller settings.
• At the “No Respond” setting, the remote controller keys are disabled. Its power key (reception/standby key) is disabled too.
• At the “Limited” setting, some channel-related keys alone are operative. All the other remote controller keys (power, volume
/ , channel
/ , light control (brightness sensor), broadcast select) are inoperative.
Limit in Setting
In “No respond” setting, all the keys (including the power key) are not accepted.
• Adjustment process, inspection process and hotel only keys are valid irrespective of setting.
• All the keys can be used in adjustment process, inspection mode and hotel menu irrespective of setting.
Exception
Remarks
5 – 17
LC-40/46/52/60LE810UN (1st Edition)
6) PANEL BUTTON
Selection
Default
Explanation
Limit in Setting
Exception
Selection between “Respond” and “No respond” (loop provided)
Respond
All the operations by keys (except the power key) of the unit can be invalidated.
• Adjustment process, inspection mode and hotel menu mode can be started irrespective of setting.
• All the keys can be used in adjustment process, inspection mode and hotel menu irrespective of setting.
Remarks
7) MENU BUTTON
Selection
Default
Explanation
Limit in Setting
Exception
Selection between “Respond” and “No respond” (loop provided)
Respond
In “No respond” setting, the menu operation by the menu key of the remote control and the menu key of the unit are invalidated.
• Adjustment process, inspection mode and hotel menu mode can be started irrespective of setting.
• All the keys can be used in adjustment process, inspection mode and hotel menu irrespective of setting.
Remarks
8) ON SCREEN DISPLAY
Selection
Default
Explanation
Limit in Setting
Others
Exception
Remarks
Selection between “Yes”, “No” (loop provided)
Yes
• At the “No” setting, the following items are not displayed on screen: register, setting, adjustment menu, channel call and volume bar.
On the wide-screen models, an input selection is immediately made because the menu is not displayed.
• At the “Limited” setting, some items cannot be displayed on screen.
On the Japan-destined models, the channel call “Message” alone cannot be displayed. (This is because the channel call message may be confused with a message being sent from the hotel.)
On the North America-destined models, the OSD works the same as at the “No” setting.
• Keys falling under any of the following items become invalid.
Appearance of screen changes and the sound changes.
Personal functions which are hard to restore.
Screen display, menu, OFF-timer, ON-timer, AV MODE, screen size switching, clock setting, treble emphasis, AUDIO ONLY,
sound changeover, LANGUAGE, CLOSED CAPTION
• Simple input switching is generated. Those which are restored soon after leaving as they are and may be requested for
change by customer are not prohibited.
Brightness sensor (BACKLIGHT) and PIC. FLIP
• Such a caution which is displayed independently is displayed as it is.
Non-responding signal caution
• When CC has already been ON, CLOSED CAPTION is displayed.
9) INPUT MODE START
Selection
Default
Explanation
About options
Limit in Setting
Exception
Remarks
Selection between “Normal”, “Air ( )”, “INPUT 1/2/3”, “PC”, “HDMI 1/2/3/4/5”, “DVI” (loop provided)
Normal
In power-ON, the input source to be started or channel can be set.
(In standard mode, the operation follows the last memory.)
• All the input sources in the model are made selectable.
• In TV mode, the channel to be set follows the last memory and the content of the last memory is included in the notation by
options. Ex.) Air (2), Cable (98.1) etc.
• The display of channel setting menu and the channel setting operation are prohibited.
• In setting at “Normal”, the setting of “Input mode fixed” is changed to “Variable” and selection should be prohibited.
5 – 18
LC-40/46/52/60LE810UN (1st Edition)
10)INPUT MODE FIXED
Selection
Default
Explanation
Limit in Setting
Exception
Remarks
Selection between “Variable”, “Fixed”, “ACON (AC CTRL)” and “AC/RCON (AC/RC CTRL)” (loop provided)
– (Variable)
• At the “Fixed” setting, the TV set gets started with the settings of “Input mode start”, and then any other channels and inputs
are not accepted.
• At the “ACON (AC CTRL)” setting, the TV set gets started with the settings of “Input mode start” under AC control.
• At the “AC/RCON (AC/RC CTRL)” setting, the TV set gets started with the settings of “Input mode start” under either control.
• With the execution of hotel mode, the input source is forced to change to that set by “Input mode start” and the channel
switching and input switching are prohibited thereafter.
• ON-timer's (Wake-up timer) channel items are not displayed or the operation is prohibited. (Basically, they are not displayed.)
• The following keys are invalidated.
CH / , direct tuning button, FLASHBACK, input
However, the keys (input switching and CH /
keys) of the unit for menu operation remain valid.
None
• In the following case, setting is cancelled and mode is changed to “Variable”.
When the setting of “Input mode start” is set to “Normal”.
11)RC_PATH_THROUGH
Selection
Default
Explanation
Limit in Setting
Exception
Remarks
Selection between “OFF”, “ON: TV RCE” and “ON: TV RCD” (loop provided)
OFF
Function to feed the remote controller-received signal to Pin 9 (open) on the RS232C.
None
None
None
12)AV POSITION FIXED
Selection
Default
Explanation
Limit in Setting
Exception
Remarks
Selection between “Variable” and “Fixed” (loop provided)
Variable
In case of “Fixed” setting,
– Menu “Picture” and “Audio” setting can't be changed like “Dynamic (Fixed)”.
– When “AV Mode” key is pressed, TV just displays current AV Mode (cannot be changed.).
None
None
• When receiving with AV Position key, OPC, Dolby key and other direct audio select keys, the current display stays on and no
setting can be changed.
• Even by initializing personal information, the hotel-mode settings are kept intact. In this way, the AV positions, video and
audio adjustment settings are not initialized.
13)LOUD SPEAKER (ON/OFF)
Selection
Default
Explanation
Limit in Setting
Exception
Remarks
Selection between “ON” and “OFF” (loop provided)
ON
If “OFF” is selected, TV stops Speaker output even without Headphone connected.
None
None
• Press the volume UP/DOWN key, and the mute icon appears for 4 seconds.
• The mute key and audio-related keys are displayed with caution.
• Usually, the headphones and monitor audio outputs can be adjustable.
14)232C POWON
Selection
Default
Explanation
Limit in Setting
Exception
Remarks
Selection between “Disable” and “Enable” (loop provided)
Disable
In the standby mode, the power-on by the 232C command is enabled or disabled.
None
None
None
5 – 19
LC-40/46/52/60LE810UN (1st Edition)
15)PUBLIC MODE (ON/OFF)
Selection
Default
Explanation
Limit in Setting
Exception
Remarks
Selection between “ON” and “OFF” (loop provided)
OFF
In case of “ON”, public mode settings are effected.
None
None
The public-mode settings are operable only when this item is set at ON.
5 – 20
LC-40/46/52/60LE810UN (1st Edition)
Service
CHAPTER 6. TROUBLESHOOTING TABLE
LC-40LE810UN
Manual
[1] TROUBLESHOOTING TABLE
No video (1)
COMPOSITE: No external input video [INPUT-2]
Is INPUT-2 selected on the input select menu screen?
NO
Select INPUT-2 on the input select menu
screen for the right input signal.
YES
Is there the COMPOSITE signal input at pin (AE29) of IC3302
(CPU)?
NO
Check the line between pin (8) of J507 and pin
(AE29) of IC3302.
YES
Are the LVDS signal outputs at the LVDS 1st channel and 2nd channel of IC3302?
LVDS_TX_0_DATA0_P/N (C14/D14), LVDS_TX_0_DATA1_P/N (C15/D15),
LVDS_TX_0_DATA2_P/N (C16/D16), LVDS_TX_0_DATA3_P/N (C18/D18),
LVDS_TX_0_DATA4_P/N (C19/D19), LVDS_TX_0_CLK_P/N (C17/D17),
LVDS_TX_1_DATA0_P/N (A14/B14), LVDS_TX_1_DATA1_P/N (A15/B15),
LVDS_TX_1_DATA2_P/N (A16/B16), LVDS_TX_1_DATA3_P/N (A18/B18),
LVDS_TX_1_DATA4_P/N (A19/B19), LVDS_TX_1_CLK_P/N (A17/B17).
YES
Check the panel module.
6–1
NO
Check IC3302 and its peripheral circuits.
(IC3501/IC3502, etc.)
LC-40/46/52/60LE810UN (1st Edition)
No video (2)
COMPONENT: No external input video [INPUT-1]
Is INPUT-1 selected on the input select menu screen?
Is the INPUT-SELECT for the input signal?
NO
Select INPUT-1 on the input select menu screen for
the right input signal.
Does the COMP1_PLUG detection function?
Check the line between pin (4) of input terminal (J506)
and pin (D30) of IC3302 (CPU).
YES
Are there the COMPONENT video signal inputs at pins (AJ21) (Y)/
(AJ22) (Pb) and (AH22) (Pr) of IC3302 (CPU)?
NO
Check the line between the input terminals of J506
and IC3302.
J508 pin (5) (Y) pin (6) (Pb) pin (7) (Pr)
IC3302 pin (AJ21) pin (AJ22) pin (AH22)
YES
Are the LVDS signal outputs at the LVDS 1st channel and 2nd channel of
IC3302?
LVDS_TX_0_DATA0_P/N (C14/D14), LVDS_TX_0_DATA1_P/N (C15/D15),
LVDS_TX_0_DATA2_P/N (C16/D16), LVDS_TX_0_DATA3_P/N (C18/D18),
LVDS_TX_0_DATA4_P/N (C19/D19), LVDS_TX_0_CLK_P/N (C17/D17),
LVDS_TX_1_DATA0_P/N (A14/B14), LVDS_TX_1_DATA1_P/N (A15/B15),
LVDS_TX_1_DATA2_P/N (A16/B16), LVDS_TX_1_DATA3_P/N (A18/B18),
LVDS_TX_1_DATA4_P/N (A19/B19), LVDS_TX_1_CLK_P/N (A17/B17).
YES
Check the panel module.
6–2
NO
Check IC3302 and its peripheral circuits.
(IC3501/IC3502, etc.)
LC-40/46/52/60LE810UN (1st Edition)
No video (3)
No video at UHF/VHF broadcast signal reception
No video at digital broadcast signal reception
Is the specified TV signal selected on the input select menu screen?
Is there the analog video signal output (VIDEO) at pin (15) of tuner
(TU1102)?
Are there the video signal outputs (IF_P/N) at the pins (9) and (10) of
tuner (TU1102)?
NO
Check TU1102 and its peripheral circuits
(TUN_SDA: Pin6 of TU1102
TUN_SCL: Pin7 of TU1102, etc.).
YES
Is there the analog video signal input at pin (AD29) of IC3302
(CPU)?
NO
Check TU1102 and its peripheral circuits
(TUN_SDA: Pin6 of TU1102
TUN_SCL: Pin7 of TU1102, etc.).
YES
Are there the video signal inputs at pin (AA29) and (AB29) of IC3302
(CPU)?
NO
Check the line between IC3302 and TU1102,
and their peripheral circuits.
NO
Check the line between IC3302 and TU1102, and
their peripheral circuits (C1129/C1130, etc.).
YES
YES
Are the LVDS signal outputs at the LVDS 1st channel and 2nd channel of IC3302?
LVDS_TX_0_DATA0_P/N (C14/D14), LVDS_TX_0_DATA1_P/N (C15/D15),
LVDS_TX_0_DATA2_P/N (C16/D16), LVDS_TX_0_DATA3_P/N (C18/D18),
LVDS_TX_0_DATA4_P/N (C19/D19), LVDS_TX_0_CLK_P/N (C17/D17),
LVDS_TX_1_DATA0_P/N (A14/B14), LVDS_TX_1_DATA1_P/N (A15/B15),
LVDS_TX_1_DATA2_P/N (A16/B16), LVDS_TX_1_DATA3_P/N (A18/B18),
LVDS_TX_1_DATA4_P/N (A19/B19), LVDS_TX_1_CLK_P/N (A17/B17).
YES
Check the panel module.
6–3
NO
Check IC3302 and its peripheral circuits.
(IC3501/IC3502, etc.)
LC-40/46/52/60LE810UN (1st Edition)
No video (4)
PC: No external input video [INPUT-3]
Is INPUT-3 selected on the input select menu screen?
NO
Select INPUT-3 on the input select menu screen for the right input signal.
YES
Is IC509 (EEPROM) accessed by I2C, with PC connected, to read the DDC_I2C SCL/SDA data?
Check the DDC line and its peripheral circuits. (IC509 and its peripherals).
Are there the video signal inputs at pins (AK16) (G), (AH15) (B) and (AK17) (R) of IC3302 (CPU)?
Are there the VSYNC/HSYNC signal inputs at pins (AJ14) and (AK14) of IC3302?
NO
Check the line between SC501 and IC3302.
YES
Are the LVDS signal outputs at the LVDS 1st channel and 2nd channel of IC3302?
LVDS_TX_0_DATA0_P/N (C14/D14), LVDS_TX_0_DATA1_P/N (C15/D15),
LVDS_TX_0_DATA2_P/N (C16/D16), LVDS_TX_0_DATA3_P/N (C18/D18),
LVDS_TX_0_DATA4_P/N (C19/D19), LVDS_TX_0_CLK_P/N (C17/D17),
LVDS_TX_1_DATA0_P/N (A14/B14), LVDS_TX_1_DATA1_P/N (A15/B15),
LVDS_TX_1_DATA2_P/N (A16/B16), LVDS_TX_1_DATA3_P/N (A18/B18),
LVDS_TX_1_DATA4_P/N (A19/B19), LVDS_TX_1_CLK_P/N (A17/B17).
NO
Check IC3302 and its peripheral circuits. (IC3501/IC3502, etc.)
YES
Check the panel module.
6–4
LC-40/46/52/60LE810UN (1st Edition)
<HDMI input> No video (5)-1
HDMI: No external input video [INPUT-4]
HDMI: No external input video [INPUT-5]
Is INPUT-4 selected on the input select menu screen?
Is INPUT-5 selected on the input select menu screen?
NO
Select INPUT-4 on the input select menu screen for the
right input signal.
NO
Select INPUT-5 on the input select menu screen for the
right input signal.
YES
YES
Does the HOT PLUG detection function?
Does the DDC5V signal come from pin (18) of SC1503 to pin (46) of
IC1504 (HDMI_SW)?
YES
Does the HOT PLUG detection function?
Does the DDC5V signal come from pin (18) of SC1502 to pin (42) of
IC1504 (HDMI_SW)?
NO
Check the line between the input terminals of SC1503
and IC1504.
Check IC1504 and its peripheral circuits
(SDA0_400K: pin53 of IC1504/SCL0_400K: pin54 of
IC1504, etc.).
YES
Does the HPD signal come from pin (45) of IC1504 to pin (19) of
SC1503?
YES
NO
Check the line between the input terminals of SC1502
and IC1504.
Check IC1504 and its peripheral circuits
(SDA0_400K: pin53 of IC1504/SCL0_400K: pin54 of
IC1504, etc.).
Does the HPD signal come from pin (41) of IC1504 to pin (19) of
SC1502?
NO
Check the line between the pin (45) of IC1504 and the
pin (19) of SC1503.
Check IC1504 and its peripheral circuits
(SDA0_400K: pin53 of IC1504/SCL0_400K: pin54 of
IC1504, etc.).
YES
Are there the TMDS signal inputs at pins (19/20) (CLK-/+), (21/22)
(D0-/+), (23/24) (D1-/+), (25/26) (D2-/+), all of IC1504?
NO
Check the line between the pin (41) of IC1504 and the
pin (19) of SC1502.
Check IC1504 and its peripheral circuits
(SDA0_400K: pin53 of IC1504/SCL0_400K: pin54 of
IC1504, etc.).
Are there the TMDS signal inputs at pins (11/12) (CLK-/+), (13/14)
(D0-/+), (15/16) (D1-/+), (17/18) (D2-/+), all of IC1504?
NO
Is IC1504 (pin43/pin44) accessed by I2C, with HDMI
connected, to read the DDC_I2C SDA/SCL data?
NO
Is IC1504(pin39/pin40) accessed by I2C, with HDMI
connected, to read the DDC_I2C SDA/SCL data?
NO
Check the DDC line and its peripheral circuits.
(IC1504 and its peripherals).
NO
Check the DDC line and its peripheral circuits.
(IC1504 and its peripherals).
YES
YES
Are there the TMDS signal inputs at pins (AJ6/AK6) (CLK-/+), (AJ7/AK7) (D0-/+), (AJ8/
AK8) (D1-/+), (AJ9/AK9) (D2-/+), all of IC3302 (CPU)?
YES
Are the LVDS signal outputs at the LVDS 1st channel and 2nd channel of IC3302?
LVDS_TX_0_DATA0_P/N (C14/D14), LVDS_TX_0_DATA1_P/N (C15/D15),
LVDS_TX_0_DATA2_P/N (C16/D16), LVDS_TX_0_DATA3_P/N (C18/D18),
LVDS_TX_0_DATA4_P/N (C19/D19), LVDS_TX_0_CLK_P/N (C17/D17),
LVDS_TX_1_DATA0_P/N (A14/B14), LVDS_TX_1_DATA1_P/N (A15/B15),
LVDS_TX_1_DATA2_P/N (A16/B16), LVDS_TX_1_DATA3_P/N (A18/B18),
LVDS_TX_1_DATA4_P/N (A19/B19), LVDS_TX_1_CLK_P/N (A17/B17).
YES
Check the panel module.
6–5
NO
Check IC1504, IC3302 and their peripheral
circuits.
NO
Check IC3302 and its peripheral circuits.
(IC3501/IC3502, etc.)
LC-40/46/52/60LE810UN (1st Edition)
<HDMI input> No video (5)-2
HDMI: No external input video [INPUT-6]
HDMI: No external input video [INPUT-7]
Is INPUT-6 selected on the input select menu screen?
Is INPUT-7 selected on the input select menu screen?
NO
Select INPUT-6 on the input select menu screen for the
right input signal.
NO
Select INPUT-7 on the input select menu screen for the
right input signal.
YES
YES
Does the HOT PLUG detection function?
Does the DDC5V signal come from pin (18) of SC1501 to pin (36) of
IC1504 (HDMI_SW)?
YES
Does the HOT PLUG detection function?
Does the DDC5V signal come from pin (18) of SC1505 to pin (32) of
IC1504 (HDMI_SW)?
NO
Check the line between the input terminals of SC1501
and IC1504.
Check IC1504 and its peripheral circuits.
(SDA0_400K: pin53 of IC1504/SCL0_400K: pin54 of
IC1504, etc.).
NO
Check the line between the input terminals of SC1505
and IC1504.
Check IC1504 and its peripheral circuits
(pin53 of IC1504/SCL1: pin54 of IC1504, etc.).
YES
Does the HPD signal come from pin (35) of IC1504 to pin (19) of
SC1501?
YES
Does the HPD signal come from pin (31) of IC1504 to pin (19) of
SC1505?
NO
Check the line between the pin (31) of IC1504 and the
pin (19) of SC1501.
Check IC1504 and its peripheral circuits
(SDA0_400K: pin53 of IC1504/SCL0_400K: pin54 of
IC1504, etc.).
NO
Check the line between the pin (41) of IC1504 and the
pin (19) of SC1505.
Check IC1504 and its peripheral circuits
pin53 of IC1504/SCL1: pin54 of IC1504, etc.).
YES
Are there the TMDS signal inputs at pins (1/2) (CLK-/+), (3/4) (D0-/
+), (5/6) (D1-/+), (7/8) (D2-/+), all of IC1504?
Are there the TMDS signal inputs at pins (65/66) (CLK-/+), (67/68)
(D0-/+), (69/70) (D1-/+), (71/72) (D2-/+), all of IC1504?
NO
Is IC1504 (pin33/pin34) accessed by I2C, with HDMI
connected, to read the DDC_I2C SDA/SCL data?
NO
Is IC1504 (pin29/pin30) accessed by I2C, with HDMI
connected, to read the DDC_I2C SDA/SCL data?
NO
Check the DDC line and its peripheral circuits.
(IC1504 and its peripherals).
NO
Check the DDC line and its peripheral circuits.
(IC1504 and its peripherals)
YES
YES
Are there the TMDS signal inputs at pins (AJ6/AK6) (CLK-/+), (AJ7/AK7) (D0-/+), (AJ8/
AK8) (D1-/+), (AJ9/AK9) (D2-/+), all of IC3302 (CPU)?
NO
Check IC1504, IC3302 and their peripheral circuits.
YES
YES
Are the LVDS signal outputs at the LVDS 1st channel and 2nd channel of IC3302?
LVDS_TX_0_DATA0_P/N (C14/D14), LVDS_TX_0_DATA1_P/N (C15/D15),
LVDS_TX_0_DATA2_P/N (C16/D16), LVDS_TX_0_DATA3_P/N (C18/D18),
LVDS_TX_0_DATA4_P/N (C19/D19), LVDS_TX_0_CLK_P/N (C17/D17),
LVDS_TX_1_DATA0_P/N (A14/B14), LVDS_TX_1_DATA1_P/N (A15/B15),
LVDS_TX_1_DATA2_P/N (A16/B16), LVDS_TX_1_DATA3_P/N (A18/B18),
LVDS_TX_1_DATA4_P/N (A19/B19), LVDS_TX_1_CLK_P/N (A17/B17).
YES
Check the panel module.
6–6
NO
Check IC3302 and its peripheral circuits.
(IC3501/IC3502, etc.)
LC-40/46/52/60LE810UN (1st Edition)
No audio (1)
INPUT-1 No audio.
INPUT-2 No audio.
Is INPUT-1 selected on the input select menu screen?
Is INPUT-2 selected on the input select menu screen?
NO
Refer to “: No external input video [INPUT-1]”.
NO
Refer to “: No external input video [INPUT-2]”.
YES
Is the audio output selected for “VARIABLE” on the menu screen?
YES
Is the audio output selected for “VARIABLE” on the menu screen?
NO
Set the audio output to “FIXED”.
NO
Set the audio output to “FIXED”.
YES
YES
Does the audio signal come from pins (4) (L) and (1) (R) of input
terminal (J505) to pins (R28) (L) and (T26) (R) of IC3302 (CPU)?
Does the audio signal come from pins (4) (L) and (3) (R) of input
terminal (J507) to pins (U29)(L) and (U28) (R) of IC3302 (CPU)?
NO
Check the line between J507 and IC3302.
NO
Check the line between J505 and IC3302.
YES
YES
Does the digital audio signal come from pins (F28/F30/G28) (AUBCK/AULRCK/AOSDATA0) of
IC3302 (CPU) to pin (8/9/7) (SP_BCLK/SP_LRCLK/SP_DATA) of IC2701 (Audio DSP)?
NO
Check the line between IC3302 and IC2701,
and their peripheral circuits.
YES
• About the L/R Speakers.
Does the digital audio signal come from pins (47/43/44/45) of
IC2701 (Audio DSP) to pin (5/8/7/6) of IC2703 (AMP for L/R)?
• About the Subwoofer speaker.
Does the digital audio signal come from pins (47/43/44/46) of
IC2701 (Audio DSP) to pin (5/8/7/6) of IC2702 (AMP for SW)?
YES
• About the L/R Speakers.
Is the audio output from IC2703 as specified?
• About the Subwoofer Speaker.
IS the audio output from IC2702 as specified?
NO
Check IC2701 and its peripheral circuits. (X2701, etc.).
NO
• About the L/R Speakers.
Check IC2703 and its peripheral circuits.
• About the Subwoofer Speaker.
Check IC2702 and its peripheral circuits.
Yes
• About the L/R Speakers.
Check the connector (P2701) L/R speakers and their peripheral circuits.
• About the Subwoofer Speaker.
Check the connector (P2702), subwoofer speaker and their peripheral.
6–7
LC-40/46/52/60LE810UN (1st Edition)
No audio (2)
[PC analog audio input] INPUT-3 No audio.
[HDMI analog audio input] INPUT-4 No audio.
Is INPUT-3 selected on the input select menu screen?
Is INPUT-4 selected on the input select menu screen?
NO
Refer to “: No external input video [INPUT-3]”.
NO
Refer to “: No external input video [INPUT-4]”.
YES
Is the audio output selected for “VARIABLE” on the menu screen?
YES
Is the audio output selected for “VARIABLE” on the menu screen?
NO
Set the audio output to “FIXED”.
NO
Set the audio output to “FIXED”.
YES
Is the “PC input” - “Audio select” selected for “HDMI + Analog” on
the menu screen?
YES
Is the “PC input” - “Audio select for “Video + Audio” on the menu
screen?
NO
Set the “PC input” - “Analog select” to “Video +
Audio”.
YES
YES
NO
Set the “PC input” - “Analog select” to “HDMI +
Analog.
Does the digital audio signal come from pins (F28/F30/G28) (AUBCK/AULRCK/AOSDATA0) of
IC3302 (CPU) to pin (8/9/7) (SP_BCLK/SP_LRCLK/SP_DATA) of IC2701 (Audio DSP)?
NO
Check the line between IC3302 and IC2701,
and their peripheral circuits.
YES
• About the L/R Speakers.
Does the digital audio signal come from pins (47/43/44/45) of
IC2701 (Audio DSP) to pin (5/8/7/6) of IC2703 (AMP for L/R)?
• About the Subwoofer speaker.
Does the digital audio signal come from pins (47/43/44/46) of
IC2701 (Audio DSP) to pin (5/8/7/6) of IC2702 (AMP for SW)?
YES
• About the L/R Speakers.
Is the audio output from IC2703 as specified?
• About the Subwoofer Speaker.
IS the audio output from IC2702 as specified?
NO
Check IC2701 and its peripheral circuits. (X2701, etc.).
NO
• About the L/R Speakers.
Check IC2703 and its peripheral circuits.
• About the Subwoofer Speaker.
Check IC2702 and its peripheral circuits.
Yes
• About the L/R Speakers.
Check the connector (P2701) L/R speakers and their peripheral circuits.
• About the Subwoofer Speaker.
Check the connector (P2702), subwoofer speaker and their peripheral.
6–8
LC-40/46/52/60LE810UN (1st Edition)
No audio (3)
No audio at UHF/VHF broadcast signal reception.
No audio at digital broadcast signal reception.
Is TV selected on the input select menu screen?
Is TV selected on the input select menu screen?
NO
Refer to “No video at UHF/VHF broadcast signal
reception”.
NO
Refer to “No video at digital broadcast signal
reception”.
YES
YES
Is the audio output selected for “VARIABLE” on the menu screen?
If no video appears, refer to “No video at digital broadcast signal
reception”.
NO
Set the audio output to “FIXED”.
Is the audio output selected for “VARIABLE” on the menu screen?
NO
Set the audio output to “FIXED”.
YES
Is there the SIF signal output at pin (14) of tuner (TU1102)?
NO
Check the tuner (TU1102) and its peripheral circuits.
(I2C line: TUNER_SCL/TUNER_SDA, etc.)
YES
Does the SIF signal come from pin (14) of tuner (TU1102) to pin
(AB27) of IC3302 (CPU)?
NO
Check the line between TU1102 and IC3302, and
their peripheral circuits (Q1101, Q1102, etc.).
YES
YES
Does the digital audio signal come from pins (F28/F30/G28) (AUBCK/AULRCK/AOSDATA0) of
IC3302 (CPU) to pin (8/9/7) (SP_BCLK/SP_LRCLK/SP_DATA) of IC2701 (Audio DSP)?
NO
Check the line between IC3302 and IC2701, and
their peripheral circuits.
YES
• About the L/R Speakers.
Does the digital audio signal come from pins (47/43/44/45) of
IC2701 (Audio DSP) to pin (5/8/7/6) of IC2703 (AMP for L/R)?
• About the Subwoofer speaker.
Does the digital audio signal come from pins (47/43/44/46) of
IC2701 (Audio DSP) to pin (5/8/7/6) of IC2702 (AMP for SW)?
YES
• About the L/R Speakers.
Is the audio output from IC2703 as specified?
• About the Subwoofer Speaker.
IS the audio output from IC2702 as specified?
NO
Check IC2701 and its peripheral circuits. (X2701, etc.).
NO
• About the L/R Speakers.
Check IC2703 and its peripheral circuits.
• About the Subwoofer Speaker.
Check IC2702 and its peripheral circuits.
Yes
• About the L/R Speakers.
Check the connector (P2701) L/R speakers and their peripheral circuits.
• About the Subwoofer Speaker.
Check the connector (P2702), subwoofer speaker and their peripheral.
6–9
LC-40/46/52/60LE810UN (1st Edition)
No audio (4)
INPUT-4 No audio (HDMI connected)
INPUT-5 No audio (HDMI connected)
INPUT-6 No audio (HDMI connected)
INPUT-7 No audio (HDMI connected)
[INPUT-4 input]
Is INPUT-4 selected on the input select menu screen?
[INPUT-5 input]
Is INPUT-5 selected on the input select menu screen?
[INPUT-6 input]
Is INPUT-6 selected on the input select menu screen?
[INPUT-7 input]
Is INPUT-7 selected on the input select menu screen?
NO
Refer to “: No external input video [INPUT-4/5/6/7]”.
YES
[INPUT-4 input]
If no video appears, refer to “No external input video (HDMI) [INPUT-4]”.
[INPUT-5 input]
If no video appears, refer to “No external input video (HDMI) [INPUT-5]”.
[INPUT-6 input]
If no video appears, refer to “No external input video (HDMI) [INPUT-6]”.
[INPUT-7 input]
If no video appears, refer to “No external input video (HDMI) [INPUT-7]”.
Is the audio output selected for “VARIABLE” on the menu screen?
NO
Set the audio output to “FIXED”.
YES
Does the digital audio signal come from pins (F28/F30/G28) (AUBCK/AULRCK/AOSDATA0) of IC3302
(CPU) to pin (8/9/7) (SP_BCLK/SP_LRCLK/SP_DATA) of IC2701 (Audio DSP)?
NO
Check the line between IC3302 and
IC2701, and their peripheral circuits.
YES
• About the L/R Speakers.
Does the digital audio signal come from pins (47/43/44/45) of
IC2701 (Audio DSP) to pin (5/8/7/6) of IC2703 (AMP for L/R)?
• About the Subwoofer speaker.
Does the digital audio signal come from pins (47/43/44/46) of
IC2701 (Audio DSP) to pin (5/8/7/6) of IC2702 (AMP for SW)?
YES
• About the L/R Speakers.
Is the audio output from IC2703 as specified?
• About the Subwoofer Speaker.
IS the audio output from IC2702 as specified?
Check IC2701 and its peripheral circuits. (X2701, etc.).
NO
• About the L/R Speakers.
Check IC2703 and its peripheral circuits.
• About the Subwoofer Speaker.
Check IC2702 and its peripheral circuits.
NO
Yes
• About the L/R Speakers.
Check the connector (P2701) L/R speakers and their peripheral circuits.
• About the Subwoofer Speaker.
Check the connector (P2702), subwoofer speaker and their
peripheral.
6 – 10
LC-40/46/52/60LE810UN (1st Edition)
No audio signal at Digital Audio Output terminal (Analog sound heard)
No INPUT-4/5/6/7 (HDMI) audio.
No audio at digital broadcast signal reception.
If no video appears, refer to “No external input video (HDMI)
[INPUT-4/5/6/7]”.
If no video appears, refer to “No video at digital broadcast signal
reception”.
Is there the SPDIF signal output (OPT_OUT) at pin (J28) of IC3302 (CPU)?
NO
Check the IC3302 and its peripheral circuits.
YES
Is there the SPDIF signal (OPT_OUT) input at pin (2) of IC503 (SPDIF BUFFER & SPDIF-MUTE)?
NO
Check the line between IC3302 and IC503.
YES
Is there the MUTE signal input at pin (7) of IC503? (usual: High, Mute: Low)
NO
Check the MUTE_A_ALL and SPDIF-MUTE signals, and their peripheral circuits (Q505, D530, etc.).
YES
Is there the SPDIF signal input at pin (1) of D520 (OPTICAL OUTPUT)?
YES
Check the speakers and the optical cable.
NO
Check D520 and its peripheral circuits.
No optical output under the following conditions as per HDMI requirements.
* Audio contents protected.
* Audio frequency beyond 48kHz.
* Audio bit length beyond 16bits.
6 – 11
LC-40/46/52/60LE810UN (1st Edition)
No monitor audio output
Is the audio output from the monitor set at “VARIABLE” or “FIXED” on the menu screen?
NO
Check IC3302 (CPU) and its peripheral circuits.
YES
Are there the audio signal outputs at pins (M28) (HP/MONI_L) and (M27) (HP/MONI_R) of IC3302 (CPU)?
NO
Check IC3302 (CPU) and its peripheral circuits.
YES
Does the audio signal come from pins (M28) (HP/MONI_L) and (M27) (HP/MONI_R) of IC3302 to pins (2) (L) and (3) (R) of J504?
NO
Check the line between IC3302 and J504 and their peripheral circuits.
Check the MUTE_A_AU and HP/MONI_MUTE lines and its peripheral circuits
(Q506, D527, etc.).
YES
Check the connector (J504) and their peripheral circuits, and speakers and the Cable.
No connect network
Does the signal come to 1pin of LAN-jack J9501?
(see fig-1, fig-2)
YES
Check the interface device and peripheral circuits.
(power-LED of hub, LINK-LED of hub)
NO
Does the signal come to 12pin of IC9501?
(see fig-2) (IC9501: KSZ8041T)
YES
Check the line between J9501 and IC9501.
Check the LAN-jack J9501.
NO
Does the 3.3Vdc come to VDDA_3.3/VDDIO_3.3 of IC9501?
Does the 2.5Vdc come to VDD_1.8/VDDA_1.8 of IC9501?
NO
Check the power-circuits of D3.3V.
Check 7pin (V1.8_out) of IC9501.
YES
Does the clock signal come to 15pin of IC9501?
(25MHz, 3.3V)
NO
Check the line between X9501 and IC9501.
Check the crystal X9501. (SCA219WJ)
YES
Check IC9501 and its peripheral circuits.
fig-1 LAN-jack J9501
fig-2
1pin
6 – 12
LC-40/46/52/60LE810UN (1st Edition)
If it is not an error of power supply/LED driver,
It is start-up in the lamp error disregard mode.
Do you start?
YES
Does all LED of one line are not lighting?
NO
It doesn't light in 1 piece.
All LED boards including LED that doesn't light are exchanged.
YES
TP1 of LED board on the power supply side is confirmed.
Does the voltage hang?
NO
harness exchange
YES
Is the LED board connected with CN2?
YES
TP1 of the next LED board connected with CN2 is confirmed.
Does the voltage hang?
YES
The next LED board is seen.
NO
Even if the short-circuit connector is exchanged, do not you
light?
NO
LED board exchange.
YES
NO
THE END.
If it is not an error of power supply/LED driver,
It is start-up in the lamp error disregard mode.
Do you start?
NO
Is connected connector (LA1) with the first high LED board of the power supply board removed and do it start?
YES
All LED boards and the harness connected with LA1 are exchanged.
NO
Is connected connector (LA2) with the LED board second on the power supply board removed and do it start?
YES
All LED boards and the harness connected with LA2 are exchanged.
NO
Is connected connector (LA3) with the LED board third on the power supply board removed and do it start?
YES
All LED boards and the harness connected with LA3 are
exchanged.
NO
All LED boards are exchanged.
6 – 13
LC-40/46/52/60LE810UN (1st Edition)
Trouble Shooting Panel Module
When C-S FPC(2 pieces) is replaced, does screen display normally?
YES
Replace C-S FPC(2 pieces).
NO
When C-PWB is replaced, does screen display normally?
YES
Replace C-PWB.
(Adjust “VCOM ADJ” after replace C-PWB)
NO
Replace Panel HIRAKI.
(Adjust “VCOM ADJ” after replace Panel HIRAKI)
[2] LED flashing specification at the time of an error (Center icon LED used)
1. Display method
•
Since only the center icon LED can be used, slow flashing and fast flashing are combined.
•
Refer to Table 1.
•
The Start from the detail display. (No outline display)
•
After recovering from an error, if the same error cannot be generated again, refer to MONITOR ERR CAUSE on the process screen.
•
During version upgrade, the brightness of the flashing LED changes smoothly.
•
When completing version upgrade, the brightness of the LED changes in a staircase pattern.
2. LED flashing method
Error flashing
<Detail display example>
Center icon
ON
OFF
1600ms
400ms
400ms
•
1600ms
300ms
100ms
Flashing during Verup
ON
Center icon
OFF
500ms
•
500ms
Flashing when completing Verup
ON
Center icon
OFF
1000ms
1000ms
1000ms
1000ms
6 – 14
LC-40/46/52/60LE810UN (1st Edition)
Table 1. Concrete flashing pattern
Outline display
Slow flashing
Fast flashing
Flashes once
None
Detail display
Slow flashing
Fast flashing
Flashes once
Flashes once
Flashes twice
None
Flashes twice
Main PWB
failure
(Communication
failure, etc.)
Flashes 3 times
None
Flashes 3 times
Others
Flashes 4 times
None
Flashes 4 times
VerUP executing
VerUP succeeded
None
None
—
—
VerUP failed
Flashes smoothly
Flashes in a staircase pattern
None
Flashes once
Flashes twice
Flashes 3 times
Flashes 5 times
Flashes once
Flashes twice
Flashes 3 times
Flashes 5 times
Flashes once
Flashes twice
Flashes 3 times
—
—
—
—
Version upgrade failed
ROM data failure
None
Flashes continuously
Flashes continuously
—
—
Start-up after failing version upgrade (*4)
Item
Inverter/Lamp system failure
Power PWB
failure
(Power failure, etc.)
*2: They depend on the system. Power supply error is defined from product to product.
*3: For details, refer to ERROR STANDBY CAUSE on the adjustment process screen.
*4: If the boot section is abnormal, there is no flashing (flashing impossible).
3. New method
Note: The North American models have no flashing
pattern of slow flashing only. The detail display
is presented by combining slow flashing
Error flashing
Center icon
1600ms
400ms
400ms
Press the [MENU] key on the remote control.
Center icon
1600ms
400ms
400ms
1600ms
300ms
100ms
Flashing during Verup
Center icon
500ms
500ms
Flashing when completing Verup
Center icon
1000ms
1000ms
1000ms
1000ms
6 – 15
Cause
Lamp error
Power supply error 1 (*2) AC_DET error
Power supply error 2 (*2) UR+13V error
Power supply error 3 (*2) D3.3V error
Panel power supply error
Initial communication error
Start-up confirmation communication error
Regular communication error
Other communication error
Temperature error
Sync error
Notification from the main microcomputer (*3)
Version upgrading
Version upgrade succeeded
LC-40/46/52/60LE810UN (1st Edition)
LED flashing timing chart at the time of an error
100ms
400ms
1.6sec
1) Slow flashing
Error type
Inverter/
Lamp failure
Flashes slowly once
Power failure
Flashes slowly twice
Main CPU to main CPU
communication failure
Flashes slowly 3 times
Note
Center icon LED operation
H: On
L: Off
H: On
Refer to “Power failure details”. Flashes slowly and fast
by pressing the [MENU] key on the remote control (refer
to 3 below).
L: Off
H: On
Refer to “Communication failure details”. Flashes slowly
and fast by pressing the [MENU] key on the remote control (refer to 4 below).
Communication line failure or main CPU communication
failure. → Check debug statements for the main CPU.
Refer to “Other failure details”. Flashes slowly and fast by
pressing the [MENU] key on the remote control (refer to 5
below).
L: Off
Others
Flashes slowly 4 times
Pins are monitor microcomputer pins.
Refer to “Inverter/Lamp failure details”. Flashes slowly
and fast by pressing the [MENU] key on the remote control (refer to 2 below).
H: On
L: Off
2) Inverter/Lamp failure details (Flashes slowly once and flashes fast)
Error type
Lamp failure
Flashes fast once
Center icon LED operation
H: On
L: Off
3) Power failure details (Flashes slowly twice and flashes fast)
Error type
PS_ON
AC_DET failure
Flashes fast once
D_POW
Digital 3.3V failure
Flashes fast 3 times
PANEL_POW
Panel 12V failure
Flashes fast 5 times
Pins are monitor microcomputer pins unless otherwise specified.
ERR_PNL(40pin): Hi failure. Confirmed after 8 consecutive detections at 64msec intervals (detected only when
the backlight is on).
Note that after five detection counts, the lamp cannot be
activated except in the monitor process.
Accumulated counts are cleared to 0 by the setting in the
process A.
Note
Center icon LED operation
H: On
Pins are monitor microcomputer pins unless otherwise specified.
AC_DET(72pin) failure (L).
If error is detected during start-up or operation, the power
is turned on again by interrupt (instantaneous blackout
processing).
DET_13V(38pin) failure (L). Main 13V is not applied.
L: Off
SM_POW
Main 13V failure
Flashes fast twice
Note
H: On
If error is detected during start-up or operation, the power
is turned on again by polling.
L: Off
H: On
DET_D3V3(36pin) failure (L). Digital 3.3V is not applied.
If error is detected during start-up or operation, the power
is turned on again by polling.
L: Off
H: On
DET_PNL12V(35pin) failure (L). Panel power is not
applied.
Detection is started after turning on the panel power and
receiving command; the power is turned off by polling.
L: Off
6 – 16
LC-40/46/52/60LE810UN (1st Edition)
4) Communication failure details (Flashes slowly 3 times and flashes fast)
Error type
Initial communication reception failure
Flashes fast once
Center icon LED operation
H: On
L: Off
Start-up confirmation reception failure
Flashes fast twice
H: On
L: Off
Regular communication failure
Flashes fast 3 times
Other communication failure
Flashes fast 5 times
H: On
L: Off
H: On
5) Other failure details (Flashes slowly 4 times and flashes fast)
Monitor temperature
failure
Flashes fast once
Note
Center icon LED operation
H: On
L: Off
Main failure
Flashes fast 3 times
Basically, debug print logs are analyzed or communication logs are analyzed by a bus monitor.
Initial communication from the main CPU is not
received. (Request for the monitor model No. is not
received.)
→ Communication line failure or main CPU start-up failure
Start-up reason confirmation from the main CPU cannot
be received. (Start-up communication until start-up reason notification command is not received.)
→ Main CPU start-up failure or monitor microcomputer
reception failure
Regular communication that is performed at 1 second
intervals in the normal operation is interrupted.
→ Main CPU operation failure or monitor microcomputer reception failure
When a request (PM_REQ=H) is sent from the main
microcomputer, the request command is not output
from the main CPU, etc.
→ Main CPU operation failure or monitor microcomputer reception failure
L: Off
Error type
Note
H: On
L: Off
6 – 17
Pins are monitor microcomputer pins unless otherwise specified.
If the panel temperature is 60°C or more for 15 seconds
or more in a row, CAUTION appears on the OSD
(flashes in red in the lower right screen).
If the panel temperature is 60°C or more for 25 seconds
or more in a row, error standby is activated.
(MONITOR MAX TEMP on page 23 of the process A:
Change of temperature failure AD value): Thermistor
Main microcomputer detection error (CPU temperature
error, etc.)
The details are displayed on page 1 of the process A of
the main microcomputer.
LC-40/46/52/60LE810UN (1st Edition)
4. Monitor ERR STBY table
Outline:
Location:
Communication/Power failure detected by the monitor microcomputer is stored on EEPROM, and the last 4 abnormal states can be
confirmed in the process mode A.
Page 1 of the process mode A: MONITOR ERR CAUSE
“0” if there is no error. It is cleared to 0 on the last page of the process mode A.
Display
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
11
16
1A
1D
1E
1F
21
23
Start-up communication error 2
Start-up communication error 3
Start-up communication error 4
Start-up communication error 5
Start-up communication error 6
Start-up communication error 7
Start-up communication error 8
Start-up communication error 9
Communication error A
Communication error B
Communication error C
Communication error D
Communication error E
Communication error F
Communication error H
Panel-related error
Other error 2
Power supply error 1
Power supply error 2
Power supply error 3
Power supply error 5
Other error 3
Error description
Initial communication from the main CPU is not received.
Only the initial communication is received.
Until panel information request reception
Until initialization completion reception
Until version notification transmission
Until start-up information notification transmission
Until start-up information response reception
Until time-out setting reception
REQ time-out
Restart time-out during the beginning of time acquisition start-up
Ending sequence time-out
Preset start-up time-out during completion
download, start-up time-out
Time acquisition time-out
Regular communication time-out
Lamp failure
Monitor temperature failure
PS_ON (AC_DET) failure
D_POW (DET_13V) failure
D_POW (DET_D3V3) failure
Panel power failure
Error standby request from the main CPU
6 – 18
LC-40/46/52/60LE810UN (1st Edition)
CHAPTER 7. MAJOR IC INFORMATIONS Service
LC-40LE810UN
Manual
[1] MAJOR IC INFORMATIONS
1. MAJOR IC INFORMATIONS
1.1. IC1504 (VHiSii9287+-1Q)
This IC is 4 input and 1 output HDMI port processor.
It integrated TMDS receiver and transmitter cores capable of receiving and transmitting at 2.25Gbps. (Supports video resolutions up to 1080p, 60Hz,
12bit.)
The Equalizer circuits to adapt long cable are integrated in This IC.
EDID and DDC support for 4 HDMI/DVI ports and 1 VGA port.(This IC includes 256-byte NVRAM and 256-byte SRAM for each port(5 total).)
1.2. IC2002 (RH-iXC786WJN4Q)
The monitor microprocessor is intended to communicate with the main microprocessor and to operate the system.
It also controls power of the entire system.
1.3. IC2702, IC2703 (VHiYDA164QZ-1Y)
The Class-D type digital audio power amplifier YDA164QZ gives maximum continuous output of 10 W/ch or woofer output 15W.
1.4. IC3302 (RH-iXD058WJQZQ)
This LSI is FULL HIGH-DEFINITION 1080P DIGITAL TV SYSTEM-ON-A-CHIP.
It combines a cable/terrestrial 64/256-QAM and 8-VSB receiver, a transport processor, a digital audio processor, a high definition (HD) MPEG video
decoder, 2D graphics processing, digital processing of analog video and audio, analog video digitizer and DAC functions, stereo high-fidelity audio
DACs, HDMI receivers for 1080p 60 inputs, a 625-MHz processor, and a peripheral control unit providing a variety of television control functions.
The cable/terrestrial receiver directly samples a tuner output with an analog-to-digital converter (ADC).
The LSI digitally resample and demodulates the signal with recovered clock and carrier timing, filters and equalizes the data, and passes soft decisions to an ATSC/A74 and ITU-T J.83 Annex B-compatible decoder.
It has an MPEG-2 Digital Video Broadcasting (DVB)-compliant transport processor with advanced section filtering capability, DVB descrambler, and
an MPEG-2 (MP@HL profile) video decoder.
Audio support includes a BTSC and a Dolby AC3/MPEG-2 Layer 1, 2, audio decoder.
The LSI provides analog and digital audio/video outputs.
A SPDIF output and a pair of analog outputs (L-R) are provided via the integrated audio DACs.
The NTSC analog video decoder is supported by its own motion adaptive deinterlacing and 3D comb filtering, including 1080i deinterlacing.
The LSI includes advanced 2D graphics processing.
One transport stream input is included.
The LSI incorporates a complete ARM11-based microprocessor subsystem including caches with bridging to memory and a local bus, where external
peripherals can be attached.
Integrated peripherals include two USB 2.0, three UARTs, counter/timers and GPIO controllers.
In this tine, H264 decode/VC-I decode/secure boot function are added to this IC.
1.5. IC3501/IC3502 (RH-iXC754WJQZQ)
These are 1G bit (64M x 16bit) DDR2-1066 synchronous DRAM.
1.6. IC8401 (RH-iXC894WJQZQ)
The 512M-bit NAND flash memory device stores the main CPU program.
1.7. IC8455 (VHiR24064AS-1Y)
This is 64k-bit EEPROM device including the user setting.
1.8. IC506 (VHiM3221EiP-1Y)
This IC is a high speed, single-channel RS-232 transceiver interface device that operates from a single 3.3V power supply.
The device provides the electrical interface between an asynchronous communication controller and the serial-port connector.
This device operate at data signaling rates up to 460kbit/s.
All RS-232(Tout and Rin) and CMOS (Tin and Rout) inputs and outputs are protected against electrostatic discharge (up to +/- 15kV ESD protection).
1.9. IC9501(VHiKSZ8041T-1Y)
This IC is a single supply 10Base-T/100Base-TX Physical Layer Transceiver, which provides MII/RMII/SMII interfaces to transmit and receive data.
7–1
LC-40/46/52/60LE810UN (1st Edition)
1.10. IC2701 (VHiYSS951VZ-1Y)
Audio DSP (YSS951VZ) has digital audio adjustment function (for example, PEQ, bass/treble, balance, bass enhancer, etc.) and adjusts TVs audio
quality.
7–2
LC-40/46/52/60LE810UN (1st Edition)
CHAPTER 8. OVERALL WIRING/SYSTEM BLOCK DIAGRAM
LC-40LE810UN
Service Manual
[1] OVERALL WIRING DIAGRAM
OVERALL WIRING DIAGRAM
J
MODULE
I
1
䇼L1䇽 4
POWER Unit
40"䋺RUNTKA682WJQZ
46"䋺RUNTKA683WJQZ
52"䋺RUNTKA693WJQZ
60"䋺RUNTKA684WJQZ
H
1
䇼L2䇽 5
䇼LB䇽
9
䇼SB䇽
1
9 䇼LB䇽
1
䇼PD䇽
USB1
1 2
WOOFER
40/46"䋺RSP-ZA458WJZZ
52/60"䋺RSP-ZA457WJZZ
G
1
12
RJ45
VLR
Analog RGB
12
F
HP/Audio Out
MAIN Unit
DUNTKF452FM**
1 䇼PD䇽
䇼AC䇽
13
4
E
MDK
HDMI
1
䇼SP䇽
1
5
micro
SD
HDMI
PC Audio IN
䇼PL䇽
DDR 㪧㫆㫊㫀㫋㫀㫆㫅
41
41
LCD_CTL Unit
(ASICVer)
****
C
14
䇼PL䇽
1
41
䇼LW䇽
HDMI
1
䇼LW䇽
䇼RA䇽
1
15
1
䇼PL䇽 4
HDMI
D
䇼LW䇽
1
TUNER
NXP
Y
CLOVER
1
80
Digital Audio Output
䇼RL䇽
1
3
USB2
LCD_CTL Unit
(FPGA Ver.)
RUNTK4437**
1
䌐䌂
䌐R
䌒
䌌
RS232C
80
B
TOUCH KEY Unit
810:RUNTKA692WJQZ
820:RUNTKA690WJQZ
1
䇼RK䇽 8
1 䇼RL䇽
LOGO Unit
3
DUNTKF493FM02
R/C Unit
䇼RA䇽 1
5
DUNTKF494FM01
A
1
2
䇼RA䇽 1 2
EMBLEM Unit
DUNTKF493FM01
Rch: RSP-ZA456WJZZ
3
4
5
6
7
8
9
10
11
8–1
Lch: RSP-ZA456WJZZ
12
13
14
15
16
17
18
19
LC-40/46/52/60LE810UN (1st Edition)
[2] SYSTEM BLOCK DIAGRAM
SYSTEM BLOCK DIAGRAM
J
INPUT
2
CVBS_IN
CVBS_IN_L/R
CVBS/LR
(Mini Plug)
COMP_Y/Pb/Pr
Component
/LR
INPUT
1
MAIN
COMP_IN_L/R
B_STATU
PNL_W
I
PNL_ROM_E
PE
PNL_E
SDATA0
LRCK/SCLK/MCLK
+13V
IC2702
Woofer AMP
(0.1CH)
YDA164
IC2701
DSP
(YSS951)
IC2001
Reset
UCOM_RST
SDATA1
P2001
Connector
for Software
Write
/Emulator
BU+3.3V
RxD,TxD
RS_BUF_CNT
Thermister
+8.0V
PC_VSYNC/HSYNC
PC_R/G/B
PC/HDMI_LR
INPUT
3
D-SUB
RGB
Mute
Audio in
From CPU
PC/HDMI_LR
OPT_OUT
D
N_CPU_RST
PC_VSYNC/HSYNC
PC_R/G/B
DTV/SPDIF
RESET
+3.3V
IC506
RS232C TxRx
M3221EIP
BU+3.3V
BU+3.3V
No.9 pin RC Passthrough
CEC_0
INPUT
6
HDMI 4
INPUT
5
HDMI 3
INPUT
4
HDMI 2
INPUT
3
DDC_1
HDMI_1
DDC_0
HDMI_0
+3.3V
+3.3V
SC8452
Program Update
Connector
IC8401
NAND FLASH
1Gbit
J3302
USB
IC9501
Ethernet Bus
Interface
2
S13V
+3.3V
D+5V
BU+3.3V
D+3.3V
‫ޣ‬RL‫ޤ‬
P2006 (3p)
‫ޣ‬RA‫ޤ‬P2003(15p)
+5V
+5V
IC3301
LINE Reg.
S170B50U
D+5.6V
‫ޣ‬KY‫(ޤ‬2p)
TOUCH KEY
IC3304
LINE Reg.
S170B50U
3
MENU/POWER
INPUT/CHANNEL
VOLUME
J9501
Ethernet
A
1
UR13V
I2C_0_400KHz
CEC_0
J3301
USB
MAIN
8V
5.6V
5V
D3.3V
D1.8V
D1.26V
D1.05V
POWER CIRCUIT
DDC_2
HDMI_2
B
BackUp
Line
BU+3.3V
BU5V
IC1504
HDMI-SW
SII9287
DDC_3
HDMI_3
HDMI 1
KEY_RST
N_SRESET
MII
C
VON
IC9601
Spliter
HC2G66DP
IC2004
EEPROM
2kbit
Tr
UART_5391TO232C,UART_232CTO5391
INT0
A/D
EEPROM_SCL/SDA
IC509
EEPROM
RS-232C
PS_ON
I/O
I/O
PWM
IC3501
DDR2(1066M)
IC3502
1Gbit
DDR2(1066M)
1Gbit
USB_0
USB_1
SDIOCMD/SDIOCLK
SDI0㨪3
ONDD8㨪
15
ONDA6㨪
RGB/HDMI
Audio
(Mini Plug)
OFL2
AC_DET
PNL_POW
SIF
UART-0
UART-1
UART-2
INPUT
3/4
STB
AC_DET
OFL1
CVBS_IN_L/R
COMP_IN_L/R
OPT_OUT
LAMP_ERR
STB_CPU
27.000MHz
X3302
X'tal
HP/MONI_L/R
SIF
OPTICAL
OUT
PWM_0
PWM_1
Audio out
HP/MONI_L/R
IC503
OPT OUT
T7SET08
I/O
Digital AV decode & Main CPU
SPI_FLASH
/NAND Flash
Audio
Out
(Mini Plug)
E
I2S(SDATA/LRCK/SCLK)
I/O
I/O I2C
IC3302
MT5391W(FHD)
H.264 / VC-1
DDC_I2C_1
HDMI_1
Disclete
Mute
N_SRESET
+1.05V
RGB HV(AK14,AJ14)
RGB in(AK17)
I/O
I/O
PM_REQ, CBOOTS
+1.25V
I2C_1
I2C_2
I/O
I/O
PNL_POW
(400KHz 3.3V)
A/D
DET_13V,DET_5V
I2C_0
THERMO
RC,OPC
SIF
F
+1.8V
TUNER_I2C
I2C_0
UART
32.768kHz
20MHz
X2002
Xtal
+3.3V
TUNER_I2C (400KHz 3.3V)
FRAME
O_S_SET
ILL CTRL1
ILL CTRL2
IF_AGC
D_IF_IN-/+
X2001
Xtal
DET_SYNC
SUB MCU
KEY_POW,KEY_SCL,KEY_SDA
CVBS
N_TUN_RST
IF_AGC
D_IF IN-/+
CNVss
UART
WP
TU1101
Analog/
Digital
Si Tuner
LVDS OUT
RF IN
CVBS
+5V
Component
G
IC2008
Gate
7WH126FU
RxD,TxD
DET_PNL12V
I/O
IC2002
M16C/64A
IXC786WJ
4
5
‫ޣ‬LB‫ޤ‬P9602
(9pin )
䇼SP䇽
P2702
EXT-SP
IC2601
Spliter
HC2G66DP
BU+3.3V
‫ޣ‬PD‫ޤ‬POWER˴P9601(12PIN)
Woofer
+3.3V
PS_ON
H
IC8455
EEPROM
64kbit
+3.3V
+1.8V
‫ޣ‬LW‫ޤ‬P2601
(41p )
+13V
IC2703
SP AMP(2CH)
YDA164
䇼SP䇽
P2701
EXT-SP
AC_DET
SPEAKER
I2C_0 (400KHz)
I2C_0 (400KHz)
24.576MHz
X2701
X'tal
6
7
8
9
10
11
8–2
12
13
14
‫ޣ‬RA‫(ޤ‬5p)
RC
R/C
OPC
‫ޣ‬RI‫(ޤ‬2p)
‫ޣ‬RL‫(ޤ‬3p)
ICON
LOGO
Only
LE820U
15
16
17
18
19
LC-40/46/52/60LE810UN (1st Edition)
PartsGuide
PARTS GUIDE
No. S30E840LE810U
LCD COLOR TELEVISION
LC-40LE810UN
LC-46LE810UN
LC-52LE810UN
LC-60LE810UN
MODELS
CONTENTS
[1]
PRINTED WIRING BOARD
ASSEMBLIES
[7]
SUPPLIED ACCESSORIES
[2]
LCD PANEL
[8]
PACKING PARTS (LC-40LE810UN)
(NOT REPLACEMENT ITEM)
[3]
CABINET AND MECHANICAL
PARTS (LC-40LE810UN)
[9]
PACKING PARTS (LC-46LE810UN)
(NOT REPLACEMENT ITEM)
[4]
CABINET AND MECHANICAL
PARTS (LC-46LE810UN)
[10] PACKING PARTS (LC-52LE810UN)
(NOT REPLACEMENT ITEM)
[5]
CABINET AND MECHANICAL
PARTS (LC-52LE810UN)
[11] PACKING PARTS (LC-60LE810UN)
(NOT REPLACEMENT ITEM)
[6]
CABINET AND MECHANICAL
PARTS (LC-60LE810UN)
[12] SERVICE JIGS
(USE FOR SERVICING)
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these
parts with specified ones for maintaining the safety and performance of the set.
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
LC-40/46/52/60LE810UN (1st Edition)
NO.
PARTS CODE
PRICE NEW PART
RANK MARK DELIVERY
DESCRIPTION
[1] PRINTED WIRING BOARD ASSEMBLIES
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
DKEYMF452FM01
DUNTKF493FM01
DUNTKF494FM01
RUNTKA692WJQZ
RUNTKA682WJQZ
RUNTKA683WJQZ
RUNTKA693WJQZ
RUNTKA684WJQZ
RUNTKA692WJQZ
RUNTK4437TPZZ
RUNTK4437TPZA
RUNTK4437TPZB
RUNTK4437TPZC
RUNTK4462TPZZ
RUNTK4461TPZZ
RUNTK4460TPZZ
RUNTK4458TPZZ
RUNTK4459TPZZ
BM
AS
BP
BQ
BS
AS
CB
CB
CB
CB
BD
BE
BF
BH
BB
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
MAIN Unit
ICON Unit
R/C, LED Unit
KEY Unit
POWER/LED Drive Unit (LC-40LE810UN)
POWER/LED Drive Unit (LC-46LE810UN)
POWER/LED Drive Unit (LC-52LE810UN)
POWER/LED Drive Unit (LC-60LE810UN)
TOUCH SENSOR Unit
LCD CONTROL Unit (LC-40LE810UN)
LCD CONTROL Unit (LC-46LE810UN)
LCD CONTROL Unit (LC-52LE810UN)
LCD CONTROL Unit (LC-60LE810UN)
LED PWB Unit (LC-40LE810UN), x4
LED PWB Unit (LC-46LE810UN), x4
LED PWB Unit (LC-52LE810UN), x4
LED PWB Unit (LC-60LE810UN), x4
LED PWB Unit (LC-60LE810UN), x4
N
N
N
N
X
X
X
X
40" LCD Panel Module Unit (LK400D3LWF2Z)
46" LCD Panel Module Unit (LK460D3LWA2Z)
52" LCD Panel Module Unit (LK520D3LWA2Z)
60" LCD Panel Module Unit (LK600D3LW2BZ)
[2] LCD PANEL
N
N
N
N
R1LK400D3LWF2Z
R1LK460D3LWA2Z
R1LK520D3LWA2Z
R1LK600D3LW2BZ
2
LC-40/46/52/60LE810UN (1st Edition)
[3] CABINET AND MECHANICAL PARTS (LC-40LE810UN)
1
J
a
31
30
k
K
e
31
ICON
Unit
1-2
f
d
POWER/LED
27 DRIVE
Unit
g
m
TOUCH
b R/C, SENSOR
LED Unit Unit
n
17
F
23
42
3
MAIN
Unit
20
27
j
k
17 24
12
27
H
40
18
27
13
41
F
27
27
11
40
e
27
27
G
15
j
13
32
h
29
d
10
41
b
2
34
35
27
33
2-2
2-1
E
G
25
k
32
h
28
21
20
27
n
26
19
14
f
B
a
27
9
g
22
E
9
7
m
2-9
2-11
34
5
2-3
B
4
2-5
40" LCD
PANEL Module
14
27
6
14
2-6
45
27
14
C
2-13
45-3
A
27
43
44
A
44
2-12
27
3
36
2-4
2-13
2-10
14
16
8
34
C
38
37
LC-40/46/52/60LE810UN (1st Edition)
NO.
PARTS CODE
PRICE NEW PART
RANK MARK DELIVERY
DESCRIPTION
[3] CABINET AND MECHANICAL PARTS (LC-40LE810UN)
!
1
1-2
2
2-1
2-2
2-3
2-4
2-5
2-6
2-9
2-10
2-11
2-12
2-13
3
4
5
6
7
8
9
10
11
12
12-1
12-2
13
14
15
16
16-1
16-2
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
40
41
42
43
44
45
45-3
CCABAC527WJ31
HDECQB442WJ3A
CCABBB693WE01
GCABBB693WJSA
HiNDPD877WJSA
HiNDPD700WJSA
PSPAHC152WJ3Z
PSPAZC461WJZZ
PZETKA545WJKZ
PSPAHC159WJZZ
PSPAHC160WJZZ
PSPAHC166WJZZ
PSPAHC167WJZZ
PSPAHC168WJZZ
QACCDA074WJPZ
LHLDKA011WJKZ
GCOVAD699WJ3A
GCOVAD696WJ3A
LANGKC695WJFW
HiNDPD718WJSA
LANGKC689WJM1
LANGKC694WJFW
LANGKC696WJFW
CANGKC697WJ01
LANGKC697WJFW
PSPAHC165WJZZ
LHLDWA175WJUZ
LHLDWA298WJKA
PZETKA544WJKZ
CANGKC699WJ31
LANGKC699WJFW
Not available
LHLDZA587WJKZ
GCOVAD734WJ00
GCOVAD735WJ00
NSFTZA362WJFW
RSP-ZA458WJZZ
QCNW-K548WJQZ
QCNW-K550WJQZ
QCNW-K552WJQZ
QCNW-K553WJQZ
QCNW-K576WJQZ
XBPS730P06WS0
LX-BZA364WJF7
QCNW-K551WJQZ
QCNW-K554WJQZ
RSP-ZA456WJZZ
XBPS730P10WS0
LX-BZA170WJF9
XBPS830P08JS0
XBPS830P14JS0
XEBS940P10000
TLABNB037WJZZ
TLABNC391WJZZ
PSPAGA889WJKZ
PSPAGA891WJKZ
PZETKA562WJKZ
CDAi-A653WJ01
CANGKC707WJ01
CX-BZA363WJ01
XBBS840P08000
BS
AA
BL
BF
AF
AD
AA
AC
AX
AA
AB
AB
AB
AB
AG
AB
AC
AE
AD
AB
AE
AD
AD
AD
AA
AC
AD
AV
AR
AQ
AC
AF
AE
AA
AX
AE
AD
AE
AF
AP
AA
AA
AQ
AG
AU
AA
AA
AB
AA
AB
AB
AD
AC
AC
BE
AT
AD
AA
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
J
J
X
X
X
X
J
X
X
X
X
X
X
X
X
X
J
X
X
X
X
J
X
J
X
J
X
X
X
X
X
X
X
X
X
Front Cabinet Ass'y
R/C Decoration Cover
Rear Cabinet Ass'y
Rear Cabinet
Terminal Label S
Terminal Label B
Spacer
Spacer A
Insulator
300x10x0.5 Himeron
170x10x0.5 Himeron
445x8x0.5 Himeron, x2
555x8x0.5 Himeron, x2
565x8x0.5 Himeron, x2
AC Cord
AC Cord Band
AC Cord Cover
Stand Cover
LCD Fixing Metal Angle B-R
Model Label
Vesa Angle, x2
LCD Fixing Metal Angle B-L
LCD Fixing Metal Angle T-L
LCD Fixing Metal Angle T-R Ass'y
LCD Fixing Metal Angle T-R
Himeron
Holder, x3
Holder, x5
Insulator
Stand Angle Ass'y
Stand Angle
Spacer, x2
Holder, x6
Terminal Cover S
Terminal Cover B
Shaft, x4
Speaker (Sub Woofer)
Connecting Cord (PD:POW-MAIN)
Connecting Cord (PL:POW-LCD_CTL)
Connecting Cord (LB:POW-MAIN)
Connecting Cord (SB:MAIN-WOOFER)
Connecting Cord (LW:MAIN-LCD_CTL)
Screw, x37 (for Chassis, PWB)
Screw, x4 (for Sub Woofer)
Connecting Cord (RA:MAN-EN/KY/RC)
Connecting Cord (SP:MAN-SP(L/R))
Speaker, x2 (L/R)
Screw, x3 (for LCD)
Screw, x4
Screw, x13 (for Rear Cabinet)
Screw (for Terminal)
Screw, x4 (for Speaker)
Serial Label (Back)
Serial Label (Side)
Spacer Coner-Top, x2
Spacer Coner-Bottm, x2
AC Barrier
Stand Base Ass'y
Support Ass'y
Stand Screw Ass'y
Screw
4
LC-40/46/52/60LE810UN (1st Edition)
[4] CABINET AND MECHANICAL PARTS (LC-46LE810UN)
8
1
a
26
33
L
J
f
POWER/LED
DRIVE
34
Unit
22
g
j
L
26
k
F
28
1-2
d
e
ICON
Unit
j
TOUCH
SENSOR
b R/C,
Unit
LED Unit
48
3
34
MAIN h
Unit
25
29
j
23
22
27
E
12
H
20
41
37
f
B
24
F
20
36
34
38 14
20
37
15
j
K
46" LCD
PANEL Module
18
19
44
43
2-1
46
2-3
5
B
2-9
4
42
2-5
39
C
34
34
21
46
2-2
34
21
34
10
2
2-8
6
35
41
E
21 17
20
17
49
b
G
34
13
16
h
d
h
34 34
34
47
G
30
34
11
20
41
h
e
34
34
31
32
25
20
7
g
34
34
36
k
a
C
2-7
2-6
A
46
2-11
51
50
51-3
A
5
2-10
45
2-4
2-11
40
9
LC-40/46/52/60LE810UN (1st Edition)
NO.
PARTS CODE
PRICE NEW PART
RANK MARK DELIVERY
DESCRIPTION
[4] CABINET AND MECHANICAL PARTS (LC-46LE810UN)
!
1
1-2
2
2-1
2-2
2-3
2-4
2-5
2-6
2-7
2-8
2-9
2-10
2-11
3
4
5
6
7
8
9
10
11
12
12-1
12-2
13
14
15
16
17
18
18-1
18-2
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
51-3
CCABAC528WJ31
HDECQB442WJ3A
CCABBB694WE01
Not available
HiNDPD877WJSA
HiNDPD700WJSA
PSPAHC152WJ3Z
PSPAZC461WJZZ
PZETKA539WJKZ
PSPAHC159WJZZ
PSPAHC160WJZZ
PSPAHC169WJZZ
PSPAHC170WJZZ
PSPAHC171WJZZ
QACCDA074WJPZ
LHLDKA011WJKZ
GCOVAD699WJ3A
GCOVAD697WJ3A
LANGKC695WJFW
LHLDWA176WJUZ
HiNDPD719WJSA
LANGKC694WJFW
LANGKC696WJFW
CANGKC697WJ01
LANGKC697WJFW
PSPAHC165WJZZ
LANGKC698WJFW
LANGKC810WJFW
PMLT-A632WJZZ
PCLiCA014WJKZ
QEARZA186WJZZ
CANGKC700WJ31
LANGKC700WJFW
Not available
RSP-ZA458WJZZ
LHLDWA175WJUZ
LHLDWA289WJKZ
LHLDZA587WJKZ
GCOVAD734WJ00
GCOVAD735WJ00
NSFTZA362WJFW
RSP-ZA456WJZZ
QCNW-K548WJQZ
QCNW-K550WJQZ
QCNW-K552WJQZ
QCNW-K570WJQZ
QCNW-K577WJQZ
QCNW-K572WJQZ
QCNW-K559WJQZ
XBPS730P06WS0
LX-BZA364WJF7
PSPAGA889WJKZ
PSPAGA891WJKZ
PSPAGA892WJKZ
TLABNB037WJZZ
TLABNC391WJZZ
XBPS730P10WS0
PSPAHC165WJZZ
LX-BZA170WJF9
XBPS830P14JS0
XEBS940P10000
XBPS830P08JS0
PZETKA538WJKZ
PZETKA562WJKZ
CDAi-A654WJ01
CANGKC708WJ01
CX-BZA363WJ01
XBBS840P08000
BS
AA
BN
AF
AD
AA
AC
AZ
AA
AB
AB
AB
AB
AG
AB
AC
AF
AD
AC
AB
AD
AD
AD
AA
AB
AC
AC
AA
AD
AR
AQ
AX
AC
AC
AC
AF
AE
AA
AU
AE
AD
AE
AE
AQ
AQ
AG
AA
AA
AD
AC
AC
AB
AA
AA
AA
AA
AB
AB
AW
AC
BG
AV
AD
AA
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
J
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
J
J
J
X
X
X
X
X
X
X
X
X
X
X
J
X
X
X
X
X
X
J
X
X
X
J
J
X
X
X
X
X
X
Front Cabinet Ass'y
R/C Decoration Cover
Rear Cabinet Ass'y
Rear Cabinet
Terminal Label S
Terminal Label B
Spacer
Spacer 1
Insulator
170x10x0.5 Himeron
300x10x0.5 Himeron
510x8x0.5 Himeron, x2
630x8x0.5 Himeron
385x8x0.5 Himeron, x2
AC Cord
AC Cord Band
AC Cord Cover
Stand Cover
LCD Fixing Metal Angle B-R
Holder, x2
Model Label
LCD Fixing Metal Angle B-L
LCD Fixing Metal Angle T-L
LCD Fixing Metal Angle T-R Ass'y
LCD Fixing Metal Angle T-R
Himeron
LCD Fixing Metal Angle B-MA
LCD Fixing Metal Angle B-MB
Absorber
Clip, x2
Ground Part, x2
Stand Angle Ass'y
Stand Angle
Spacer, x2
Speaker (Sub Woofer)
Holder, x7
Holder, x3
Holder, x6
Terminal Cover S
Terminal Cover B
Shaft, x4
Speaker, x2 (L/R)
Connecting Cord (PD:POW-MAIN)
Connecting Cord (PL:POW-LCD_CTL)
Connecting Cord (PL:POW-LCD_CTL)
Connecting Cord (SB:MAIN-WOOFER)
Connecting Cord (LW:MAIN-LCD_CTL)
Connecting Cord (RA:MAN-EM/KY/RC)
Connecting Cord (SP:MAN-SP(L/R))
Screw, x34 (for Chassis, PWB)
Screw, x4 (for Sub Woofer)
Spacer (Coner Top) (15x25x6), x2
Spacer (Coner Bottom) (18x18x4), x2
Spacer (Coner Top) (15x25x8)
Serial Label (Back)
Serial Label (Side)
Screw, x5 (for LCD)
Himeron, x2
Screw, x4
Screw, x1 (for Terminal)
Screw, x4 (for Speaker)
Screw, x17 (for Rear Cabinet)
Insulator
AC Barrier
Stand Base Ass'y
Support Ass'y
Stand Screw Ass'y
Screw
6
LC-40/46/52/60LE810UN (1st Edition)
[5] CABINET AND MECHANICAL PARTS (LC-52LE810UN)
a
43
45
1
K
8
22
J
45
f
POWER/LED
DRIVE
37
Unit
g
k
25
m
K
F
30
e
1-2
ICON
Unit
d
3
j
TOUCH
SENSOR
b
R/C,
Unit
LED Unit
MAIN
n
Unit
28
53
37
31
25
26
k
29
E
14
37
22
23
37 22
g
44
B
36
44
16
24
G
12
35
G
46
2
37
b
21
n
37
15
22
17
j
37
37
37
19
h
d
38
33
37
13
23
D
F
34
37
22
e
37
23
47
49
K
E
2-1
44
18
37
23
37
23
20
C
37
2-5
2-7
56
55
48
2-4
2-7
18
54
4
46
2-11
A
37
6
5
2-3
2-6
C
4
2-9
37
23
46
2-2
B
52" LCD
PANEL Module
A
56-3
55
7
2-10
2-8
2-9
m
h
42
28
7
35
32
27
37
H
34
f
a
51
11
50
LC-40/46/52/60LE810UN (1st Edition)
NO.
PARTS CODE
PRICE NEW PART
RANK MARK DELIVERY
DESCRIPTION
[5] CABINET AND MECHANICAL PARTS (LC-52LE810UN)
!
1
1-2
2
2-1
2-2
2-3
2-4
2-5
2-6
2-7
2-8
2-9
2-10
2-11
3
4
5
6
7
8
11
12
13
14
15
16
17
18
19
20
20-1
20-2
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
42
43
44
45
46
47
48
49
50
51
53
54
55
56
56-3
CCABAC529WJ31
HDECQB442WJ3A
CCABBB695WJ31
Not available
HiNDPD699WJSA
HiNDPD700WJSA
PSPAHC152WJ3Z
PSPAHC159WJZZ
PSPAHC160WJZZ
PSPAHC166WJZZ
PSPAHC172WJZZ
PSPAHC173WJZZ
PSPAZC461WJZZ
PZETKA539WJKZ
QACCDA074WJPZ
LHLDKA011WJKZ
GCOVAD699WJ3A
GCOVAD697WJ3A
LANGKC695WJFW
LHLDWA176WJUZ
HiNDPD720WJSA
LANGKC694WJFW
LANGKC696WJFW
LANGKC697WJFW
LANGKC698WJFW
LANGKC810WJFW
PMLT-A632WJZZ
QEARZA186WJZZ
PCLiCA014WJKZ
CANGKC700WJ31
LANGKC700WJFW
Not available
RSP-ZA457WJZZ
LHLDWA175WJUZ
LHLDWA289WJKZ
PZETKA538WJKZ
LHLDZA587WJKZ
GCOVAD734WJ00
GCOVAD735WJ00
NSFTZA362WJFW
QCNW-K548WJQZ
QCNW-K550WJQZ
QCNW-K552WJQZ
QCNW-K577WJQZ
QCNW-K574WJQZ
PSPAGA889WJKZ
PSPAGA891WJKZ
PSPAGA892WJKZ
XBPS730P06WS0
LX-BZA364WJF7
QCNW-K562WJQZ
QCNW-K579WJQZ
XBPS730P10WS0
RSP-ZA456WJZZ
XBPS830P08JS0
XBPS830P14JS0
XEBS940P10000
LX-BZA170WJF9
TLABNB037WJZZ
TLABNC391WJZZ
PZETKA562WJKZ
CDAi-A654WJ01
CANGKC708WJ01
CX-BZA363WJ01
XBBS840P08000
BT
AA
BM
AF
AD
AA
AA
AB
AB
AB
AB
AC
AZ
AG
AB
AC
AF
AD
AC
AB
AD
AD
AD
AB
AC
AC
AD
AA
AR
AQ
AX
AC
AC
AW
AC
AF
AE
AA
AE
AD
AE
AQ
AE
AD
AC
AC
AA
AA
AR
AG
AA
AU
AB
AA
AB
AA
AB
AC
BG
AD
AA
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
J
X
X
X
X
X
X
X
X
X
X
X
X
X
J
J
X
J
X
X
X
X
X
X
X
X
X
X
X
J
X
X
X
J
X
J
X
J
X
X
X
X
X
X
X
X
Front Cabinet Ass'y
R/C Decoration Cover
Rear Cabinet Ass'y
Rear Cabinet
Terminal Label S
Terminal Label B
AC Himeron
170x10x0.5 Himeron
300x10x0.5 Himeron
445x8x0.5 Himeron, x2
575x8x0.5 Himeron, x2
695x8x0.5 Himeron, x2
Spacer A
Power Barrir
AC Cord
AC Cord Band
AC cord Cover
Stand Cover
LCD Fixing Metal Angle B-R
Holder, x2
Model Label
LCD Fixing Metal Angle B-L
LCD Fixing Metal Angle T-L
LCD Fixing Metal Angle T-R
LCD Fixing Metal Angle B-MA
LCD Fixing Metal Angle B-MB
Absorber
Ground Part, x2
Clip, x2
Stand Angle Ass'y
Stand Angle
Spacer, x2
Speaker (Sub Woofer)
Holder, x10
Holder, x6
Insulator
Holder, x6
Terminal Cover S
Terminal Cover B
Shaft, x4
Connecting Cord
Connecting Cord (PL:POW-LCD_CTL)
Connecting Cord (LB:POW-MAIN)
Connecting Cord (LW:MAIN-LCD_CTL)
Connecting Cord (SB:MAIN-WOOFER)
Spacer (Coner Top) (15x25x6) x2
Spacer (Coner Bottom) (18x18x4) x2
Spacer (Coner Top) (15x25x8)
Screw, x34 (for Chassis, PWB)
Screw, x4 (for Sub Woofer)
Connecting Cord (RA:MAN-EN/KY/RC)
Connecting Cord (SP:MAN-SP(L/R))
Screw, x6 (for LCD)
Speaker, x2 (L/R)
Screw, x19 (for Rear Cabinet)
Screw (for Terminal)
Screw, x4 (for Speaker)
Screw, x4
Serial Label (Back)
Serial Label (Side)
AC Barrier
Stand Base Ass'y
Support Ass'y
Stand Screw Ass'y
Screw
8
LC-40/46/52/60LE810UN (1st Edition)
[6] CABINET AND MECHANICAL PARTS (LC-60LE810UN)
a
21
1
37
K
J
51
MAIN
Unit k
21
38
35
28
29
m
32
E
K
d
36
51
ICON
Unit
TOUCH
SENSOR
b R/C,
Unit
LED Unit
f
g
38
9
g
B
POWER/LED
DRIVE
38
Unit
28
8
38
7
3
24
26
55
40
b
31
10
53
d
F
39
H
f
n
39
h
e
m
38
n
34
30
e
1-2
a
38
24
54
38
55
56
j
38
F
10
G
40
h
j
27
47
33
38
22
G
k
10
23
56
25
L
E
40
41
2-2
2
60" LCD
PANEL Module
C
18
5
2-3
4
41
43
A
41
B
38
46
42
44
2-1
19
41
2-8
20
2-10
2-6
6
2-5
17
45
A
2-9
2-7
13
2-8
43
2-4
2-8
50
9
49
LC-40/46/52/60LE810UN (1st Edition)
NO.
PARTS CODE
PRICE NEW PART
RANK MARK DELIVERY
DESCRIPTION
[6] CABINET AND MECHANICAL PARTS (LC-60LE810UN)
!
1
1-2
2
2-1
2-2
2-3
2-4
2-5
2-6
2-7
2-8
2-9
2-10
3
4
5
6
7
8
9
10
13
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
49
50
51
53
54
55
56
CCABAC530WJ31
HDECQB442WJ3A
CCABBB696WE01
Not available
HiNDPD699WJSA
HiNDPD700WJSA
PSPAHC152WJ3Z
PSPAHC159WJZZ
PSPAHC160WJZZ
PSPAHC170WJZZ
PSPAHC170WJZZ
PSPAZC462WJZZ
PZETKA539WJKZ
QACCDA074WJPZ
LHLDKA011WJKZ
GCOVAD699WJ3A
GCOVAD698WJ3A
LANGKC695WJFW
LANGKC696WJFW
LANGKC697WJFW
LHLDWA175WJUZ
HiNDPD721WJSA
CANGKC709WJ01
CDAi-A655WJ01
LX-BZA366WJZZ
GCOVAD702WJKA
RSP-ZA456WJZZ
LANGKC698WJFW
LANGKC694WJFW
LANGKC701WJFW
RSP-ZA457WJZZ
LHLDWA289WJKZ
PZETKA538WJKZ
LHLDZA587WJKZ
GCOVAD734WJ00
GCOVAD735WJ00
QCNW-K550WJQZ
QCNW-K566WJQZ
QCNW-K570WJQZ
QCNW-K578WJQZ
QCNW-K575WJQZ
QCNW-K567WJQZ
QCNW-K568WJQZ
XBPS730P06WS0
XBPS840P08000
XBPS730P10WS0
XBPS830P08JS0
XBPS830P14JS0
XEBS940P10000
LX-BZA170WJF9
XBPS840P12000
XBPS950P12KS0
LX-BZA364WJF7
TLABNB037WJZZ
TLABNC391WJZZ
NSFTZA362WJFW
PSPAHC160WJZZ
PZETKA562WJKZ
PSPAGA890WJKZ
PSPAGA892WJKZ
BV
AA
BR
AF
AD
AA
AA
AB
AB
AB
AC
AZ
AG
AB
AC
AM
AD
AD
AD
AC
AB
AY
BL
AA
AR
AU
AB
AD
AF
AX
AC
AW
AC
AF
AE
AD
AE
AE
AQ
AE
AS
AG
AA
AA
AA
AB
AA
AB
AA
AA
AA
AA
AB
AA
AB
AC
AE
AC
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
J
X
X
X
X
X
X
X
X
X
X
J
X
J
X
X
X
X
X
X
X
X
X
J
X
J
J
X
J
X
X
X
X
X
X
X
X
X
X
X
Front Cabinet Ass'y
R/C Decoration Cover
Rear Cabinet Ass'y
Rear Cabinet
Terminal Label S
Terminal Label B
AC Himeron
170x10x0.5 Himeron
300x10x0.5 Himeron
630x8x0.5 Himeron, x2
385x8x0.5 Himeron, x6
Spacer B, x2
Insulator
AC Cord
AC Cord Band
AC cord Cover
Stand Cover
LCD Fixing Metal Angle B-R
LCD Fixing Metal Angle T-L
LCD Fixing Metal Angle T-R
Holder, x5
Model Label
Support Ass'y
Stand Base Ass'y
Screw, x6 (for Support Angle)
Support Cover
Speaker, x2 (L/R)
LCD Fixing Metal Angle B-MA, x4
LCD Fixing Metal Angle B-L
Stand Angle, x2
Speaker (Sub Woofer)
Holder, x4
Insulator
Holder, x6
Terminal Cover S
Terminal Cover B
Connecting Cord (PL:POW-LCD_CTL)
Connecting Cord (PD:POW-MAIN)
Connecting Cord (SB:MAIN-WOOFER)
Connecting Cord (LW:MAIN-LCD_CTL)
Connecting Cord (LB:POW-MAIN)
Connecting Cord (RA:MAN-EN/KY/RC)
Connecting Cord (SP:MAN-SP(L/R))
Screw, x27 (for Chassis, PWB)
Screw, x12 (for Stand Angle)
Screw, x9 (for LCD)
Screw, x19 (for Rear Cabinet)
Screw, x2 (for Terminal)
Screw, x7 (for Stand Cover)
Screw, x4
Screw, x3 (for Support Cover)
Screw, x4 (for Stand Fixing Metal)
Screw, x4 (for Sub Woofer)
Serial Label (Back)
Serial Label (Side)
Shaft, x4
Himeron, x2
AC Barrier
Spacer Coner-Top, x2
Spacer Coner-Bottom, x2
10
LC-40/46/52/60LE810UN (1st Edition)
[7] SUPPLIED ACCESSORIES
X4
X2
X1
X3
Operation manual
Remote control unit
Cable clamp
X10
X11
Support Ass'y
NO.
PARTS CODE
X8
Stand Screw Ass'y
PRICE NEW PART
RANK MARK DELIVERY
Connection guide
DESCRIPTION
[7] SUPPLIED ACCESSORIES
X1
X2
X3
X3
X4
X5
X6
X7
X8
X9
X10
X10
X11
X11-3
RRMCGA840WJSA
LHLDWA289WJKZ
CDAi-A653WJ01
CDAi-A654WJ01
TiNS-E589WJZZ
Not available
TCADEA243WJZZ
TMAN-A030WJZZ
TMAN-A032WJZZ
TGAN-B489WJZZ
CANGKC707WJ01
CANGKC708WJ01
CX-BZA363WJ01
XBBS840P08000
AR
AC
BE
BG
AL
AD
AB
AB
AB
AV
AD
AB
X5
N
N
N
N
N
N
N
N
N
N
N
X
J
X
X
X
X
X
X
X
X
X
X
X
Remote Control
Cable Clamp, x5
Stand Base Ass'y (LC-40LE810UN)
Stand Base Ass'y (LC-46/52LE810UN)
Operation Manual
"AAA" size battery
Enquete Card
Netflix Handbill
Conection Guide
Guarantee Card
Support Ass'y (LC-40LE810UN)
Support Ass'y (LC-46/52LE811UN)
Stand Screw Ass'y
Screw
11
“AAA” size battery
LC-40/46/52/60LE810UN (1st Edition)
[8] PACKING PARTS (LC-40LE810UN) (NOT REPLACEMENT ITEM)
X1
S8
X2
X5
S7
X4
X6
X7
X8
X9
X11
X11-3
S5
X10
S3
S3
S3
FRONT
S6
X3
S2
S4
S4
S1
S11
S11
12
LC-40/46/52/60LE810UN (1st Edition)
NO.
PARTS CODE
PRICE NEW PART
RANK MARK DELIVERY
DESCRIPTION
[8] PACKING PARTS (LC-40LE810UN) (NOT REPLACEMENT ITEM)
S1
S2
S3
S4
S5
S6
S7
S8
S11
SPAKCF500WJZZ
SPAKPB219WJZZ
SPAKXC908WJZZ
SPAKXC913WJZZ
SPAKPB526WJZZ
SPAKPB528WJZZ
SSAKA0101GJZZ
SSAKAA032WJZZ
TLABKA009WJZZ
AY
AE
AN
AT
AA
AB
AA
N
N
N
N
N
N
N
N
X
X
X
X
X
X
X
J
X
Packing Case
Wrapping Paper
Packing Add. (Top)
Packing Add. (Bottom)
Not Available Wrapping Paper with the CANGKC707WJ01
Not Available Wrapping Paper with the CDAI-A653WJ01
Polyethylene Bag
Polyethylene Bag
Case No. Label
13
LC-40/46/52/60LE810UN (1st Edition)
[9] PACKING PARTS (LC-46LE810UN) (NOT REPLACEMENT ITEM)
S8
X4
X1
S4
S9
S4
S4
S1
S3
S7
X3
S5
FRONT
5
X10
S5
S5
S12
S5
S2
S12
14
LC-40/46/52/60LE810UN (1st Edition)
NO.
PARTS CODE
PRICE NEW PART
RANK MARK DELIVERY
DESCRIPTION
[9] PACKING PARTS (LC-46LE810UN) (NOT REPLACEMENT ITEM)
S1
S2
S3
S4
S5
S6
S7
S8
S9
S12
SPAKCF501WJZZ
SPAKCF473WJZZ
SPAKPA999WJZZ
SPAKXC909WJZZ
SPAKXC914WJZZ
SPAKPB527WJZZ
SPAKPB529WJZZ
SSAKA0101GJZZ
SSAKAA032WJZZ
TLABKA009WJZZ
AY
AK
AF
AN
AT
AA
AB
AA
N
N
N
N
N
N
N
N
N
X
X
X
X
X
X
X
X
J
X
Packing Case
Bottom Case
Wrapping Paper
Packing Add. (Top)
Packing Add. (Bottom)
Not Available Wrapping Paper with the CANGKC708WJ01
Not Available Wrapping Paper with the CDAI-A654WJ01
Polyethylene Bag
Polyethylene Bag
Case No. Label
15
LC-40/46/52/60LE810UN (1st Edition)
[10] PACKING PARTS (LC-52LE810UN) (NOT REPLACEMENT ITEM)
S8
X4
X6
X8
X9
X1
S9
X2
X5
X11
X11-3
S4
S4
S4
S1
S7
X3
S3
S5
FRONT
S6
X10
S5
S5
S12
S5
S2
S12
16
LC-40/46/52/60LE810UN (1st Edition)
NO.
PARTS CODE
PRICE NEW PART
RANK MARK DELIVERY
DESCRIPTION
[10] PACKING PARTS (LC-52LE810UN) (NOT REPLACEMENT ITEM)
S1
S2
S3
S4
S5
S6
S7
S8
S9
S12
SPAKCF502WJZZ
SPACKF474WJZZ
SPAKPA992WJZZ
SPAKXC910WJZZ
SPAKXC915WJZZ
SPAKPB527WJZZ
SPAKPB529WJZZ
SSAKA0101GJZZ
SSAKAA032WJZZ
TLABKA009WJZZ
AZ
AK
AF
AP
AT
AA
AB
AA
N
N
N
N
N
N
N
N
N
X
X
X
X
X
X
X
X
J
X
Packing Case
Bottom Case
Wrapping Paper
Packing Add. (Top)
Packing Add. (Bottom)
Not Available Wrapping Paper with the CANGKC708WJ01
Not Available Wrapping Paper with the CDAI-A654WJ01
Polyethylene Bag
Polyethylene Bag
Case No. Label
17
LC-40/46/52/60LE810UN (1st Edition)
[11] PACKING PARTS (LC-60LE810UN) (NOT REPLACEMENT ITEM)
S7
X4
X6
X7
X8
X9
S5
X1
S8
X2
X5
S5
S3
S5
S5
S5
S4
S6
S1
S6
S2
S9
S6
S6
18
LC-40/46/52/60LE810UN (1st Edition)
NO.
PARTS CODE
PRICE NEW PART
RANK MARK DELIVERY
DESCRIPTION
[11] PACKING PARTS (LC-60LE810UN) (NOT REPLACEMENT ITEM)
S1
S2
S3
S4
S5
S6
S7
S8
S9
SPAKCF503WJZZ
SPAKCF475WJZZ
SPAKPB427WJZZ
SPAKPB518WJZZ
SPAKXC911WJZZ
SPAKXC916WJZZ
SSAKA0101GJZZ
SSAKAA032WJZZ
TLABKA009WJZZ
BD
AR
AH
AE
AV
AX
AA
AB
AA
N
N
N
N
N
N
N
N
X
X
X
X
X
X
X
J
X
Packing Case
Bottom Case
Wrapping Paper
Wrapping Paper (for Stand)
Packing Add. (Top)
Packing Add. (Bottom)
Polyethylene Bag
Polyethylene Bag
Case No. Label
J
J
J
J
J
Connecting Cord
Connecting Cord
Connecting Cord
Connecting Cord
Connecting Cord
[12] SERVICE JIGS (USE FOR SERVICING)
N
N
N
N
N
QCNW-C222WJQZ
QCNW-H184WJQZ
QCNW-F676WJQZ
QCNW-G405WJQZ
QCNW-G394WJQZ
AW
AX
BH
AP
AV
19
L=1000mm
L=1000mm
L=1000mm
L=1000mm
L=1000mm
80pin LCD Control to LCD Panel Unit x2
12pin Main to Power Unit (PD)
41pin Main to LCD Control (LW)
4pin Main to LCD Control (PL)
9pin Main to Power (LB)
LC-40/46/52/60LE810UN (1st Edition)
COPYRIGHT © 2010 BY SHARP CORPORATION
ALL RIGHTS RESERVED.
No Part of this publication may be reproduced,
stored in a retrieval system, or transmitted in
any from or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.
Mar. 2010
SH. DS
SHARP CORPORATION
AV Systems Group
CS Promotion Center
Yaita,Tochigi 329-2193, Japan