VTech CS6129-52 Quick Start Guide
Add to my manualsadvertisement
Quick start guide
for models CS6128-31/CS6129/
CS6129-2/CS6129-3/CS6129-4/
CS6129-31/CS6129-32/CS6129-41/
CS6129-52/CS6129-54
Install the telephone base and charger(s)
Install the telephone base and charger(s) as shown below.
Telephone wall jack
DSL filter (not included) required if you have DSL high-speed
Internet service
Telephone base power adapter
(large)
Charger adapter
(small)
Telephone line cord
Telephone base
Electrical outlet not controlled by a wall switch
Charger
NOTES:
1.
Use only the power adapter(s) and battery(ies) supplied with your VTech telephone.
2.
For complete feature instructions, please refer to your user’s manual.
Battery installation and charging
Install the battery as shown below. After installing the battery, you might be able to make and receive short calls. For best performance, charge the handset battery for at least 16 hours before use.
1
If the battery compartment cover is on the handset, press the indentation and slide the cover to remove.
2
Plug the battery securely into the plug inside the handset battery compartment, matching the color-coded label.
3
Place the battery with the label THIS SIDE
UP facing up and the wires inside the battery compartment.
4
Align the cover flat against the battery compartment, then slide it upwards until it clicks into place.
5
Charge the handset by placing it in the telephone base or charger. The
CHARGE light will be on when the handset is charging.
CHARGE light
Make, answer and end a call
Make a call
1.
Press /FLASH or .
2.
Dial the number.
-OR-
1.
Dial the number.
2.
Press /FLASH or .
•
Answer a call
Press / FLASH, or any of the dialing keys ( 0-9, #, *).
•
End a call
Press OFF/CLEAR or put the handset in the telephone base or charger.
Activate the answering system
The answering system must be turned on to answer and record messages. Press
ANS ON/OFF to turn the answering system on or off. When the answering system is turned on, it will announce “Calls will be
answered,” and the ANS ON/OFF light will be on. When the answering system is turned off, it will announce “Calls will not be answered,” and the ANS ON/OFF light will be off.
Outgoing announcement
The telephone is preset with a greeting that answers calls with “Hello, please leave a
message after the tone.” You can use this preset announcement, or replace it with your own.
To record your own announcement:
1.
Press ANNC while the telephone is not in use and the system will announce
“Announcement. Press PLAY or press
RECORD.”
2.
3.
Press RECORD and the system announces, “Record after the tone. Press
STOP when you are done.”
After the tone, speak towards the microphone at the bottom front of the telephone base from about nine inches away.
4.
5.
Press /PLAY/STOP when finished.
The answering system will automatically play the newly recorded announcement.
Press /PLAY/STOP to stop the playback at anytime.
•
•
•
•
•
To play messages:
Press /PLAY/STOP to play messages and stop playback.
Press X/DELETE while a message is playing to delete it.
Press /SKIP to skip to the next message.
Press /REPEAT to repeat the current message.
Press VOL / to raise or lower playback volume.
IMPORTANT!
•
•
If your product is not working properly:
Refer to the Troubleshooting section of the user’s manual.
Visit our website at www.vtechphones.
com or call 1 (800) 595-9511. In Canada, go to www.vtechcanada.com or dial
1 (800) 267-7377.
96-006860-030-100
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project