Thank you for purchasing this SHARP product.
To obtain the best performance from this product, please read this
manual carefully. It will guide you in operating your SHARP product.
MINI COMPONENT SYSTEM
CD-SW340 Mini Component System consisting of CD-SW340 (main
unit), CP-S340 (front speaker) and CP-SW340 (Subwoofer).
MODEL
CD-SW340
OPERATION MANUAL
Accessories
Please confirm that the following accessories are included.
Remote control 1 AM loop antenna 1
(RRMCGA161AWSA) (QANTL0010AWZZ)
Note:
Only the above accessories are included.
06/10/06
CD-SW340 FRONT.fm
FM antenna 1
(92LFANT1535A)
CD-SW340
SPECIAL NOTES
Important Instruction
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Explanation of Graphical Symbols:
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
This product is classified as a CLASS 1 LASER PRODUCT
Caution - use of any controls, adjustments or procedures
other then those specified herein may result in hazardous
radiation exposure.
2
NOTE
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
WARNING
FCC Regulations state that any unauthorized changes or modifications
to this equipment not expressly approved by the manufacturer could void
the user's authority to operate this equipment.
NOTES
It is the intent of Sharp that this product be used in full compliance
with the copyright laws of the United States and that prior permission
be obtained from copyright owners whenever necessary.
Licensed under one or more of U.S. Pat. 4,972,484, 5,214,678,
5,323,396, 5,530,655, 5,539,829, 5,544,247, 5,606,618, 5,610,985,
5,740,317, 5,777,992, 5,878,080 or 5,960,037.
0303
Note to CATV system installer:
This reminder is provided to call the CATV system installer's
attention to Article 820-40 of the National Electrical Code that
provides guidelines for proper grounding and, in particular,
specifies that the cable ground shall be connected to the
grounding system of the building, as close to the point of
cable entry as practical.
FOR YOUR RECORDS
For your assistance in reporting this unit in case of loss or theft,
please record below the model number and serial number which
are located on the rear of the unit.
Please retain this information.
Model number
.......................................................
Serial number
.......................................................
Date of purchase .......................................................
Place of purchase .......................................................
0202
03/12/17
CD-SW340 02-43.fm
IMPORTANT SAFETY INSTRUCTIONS
Electricity is used to perform many useful functions, but it can also
cause personal injuries and property damage if improperly handled.
This product has been engineered and manufactured with the
highest priority on safety. However, improper use can result in
electric shock and/or fire. In order to prevent potential danger, please
observe the following instructions when installing, operating and
cleaning the product. To ensure your safety and prolong the service
life of this product, please read the following precautions carefully
before use.
CD-SW340
10) Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from
the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
2) Keep these instructions.
13) Unplug this apparatus during lightning storms or when unused for
long periods of time.
5) Do not use this apparatus near water.
14) Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.
6) Clean only with dry cloth.
Additional Safety Information
7) Do not block any ventilation openings. Install in accordance with
the manufacturer’s instructions.
15) Power Sources - This product should be operated only from the
type of power source indicated on the marking label. If you are
not sure of the type of power supply to your home, consult your
product dealer or local power company. For product intended
to operate from battery power, or other sources, refer to the
operating instructions.
3) Heed all warnings.
4) Follow all instructions.
8) Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than the other.
A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult an electrician
for replacement of the obsolete outlet.
Important Instruction
1) Read these instructions.
16) Overloading - Do not overload wall outlets, extension cords, or
integral convenience receptacles as this can result in a risk of
fire or electric shock.
17) Object and Liquid Entry - Never push objects of any kind into
this product through openings as they may touch dangerous
voltage points or short-out parts that could result in a fire or
electric shock. Never spill liquid of any kind on the product.
3
03/12/17
CD-SW340 02-43.fm
Important Instruction
CD-SW340
IMPORTANT SAFETY INSTRUCTIONS (continued)
18) Damage Requiring Service - Unplug this product from the wall
outlet and refer servicing to qualified service personnel under
the following conditions :
a) When the AC cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the
product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following
the operating instructions. Adjust only those controls
that are covered by the operating instructions as an
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the product to its normal
operation,
e) If the product has been dropped or damaged in
any way, and
f) When the product exhibits a distinct change in
performance - this indicates a need for service.
19) Replacement Parts - When replacement parts are required,
be sure the service technician has used replacement parts
specified by the manufacturer or have the same characteristics
as the original part. Unauthorized substitutions may result in
fire, electric shock, or other hazards.
20) Safety Check - Upon completion of any service or repairs to this
product, ask the service technician to perform safety checks to
determine that the product is in proper operating condition.
21) Wall or ceiling mounting - When mounting the product on a wall
or ceiling, be sure to install the product according to the method
recommended by the manufacturer.
22) Power Lines - An outside antenna system should not be located
in the vicinity of overhead power lines or other electric light or
power circuits,or where it can fall into such power lines or circuits.
When installing an outside antenna system, extreme care should
be taken to keep from touching such power lines or circuits as
contact with them might be fatal.
23) Outdoor Antenna Grounding - If an outside antenna or cable system
is connected to the product, be sure the antenna or cable system is
grounded so as to provide some protection against voltage surges
and built-up static charges. Article810 of the National Electrical Code,
ANSI/NFPA 70, provides information with regards to proper grounding
of the mast and supporting structure, grounding of the lead-in wire to
an antenna discharge unit, connection to grounding electrodes, and
requirements for the grounding electrode.
Example of antenna grounding as per
National Electrical Code, ANSI/NFPA 70
ANTENNA LEAD IN WIRE
GROUND
CLAMP
ANTENNA DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
NEC - NATIONAL ELECTRICAL CODE
S2898A
P OWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
24) Protective Attachment Plug - The product is equipped with an attachment
plug having overload protection. This is a safety feature. See Instruction
Manual for replacement or resetting of protective device. If replacement
of the plug is required, be sure the service technician has used a replacement plug specified by the manufacturer that has the same overload
protection as the original plug.
25) Stand - Do not place the product on an unstable cart, stand, tripod or
table. Placing the product on an unstable base can cause the product to
fall, resulting in serious personal injuries as well as damage to the product.
Use only a cart, stand, tripod, bracket or table recommended by the
manufacturer or sold with the product. When mounting the product on a
wall, be sure to follow the manufacturer’s intructions. Use only the mounting
hardware recommended by the manufacturer.
4
03/12/17
CD-SW340 02-43.fm
Contents
CD-SW340
Page
Products that have earned
the ENERGY STAR® are
designed to protect the
environment through
superior energy efficiency.
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Controls and indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 - 10
Preparation for Use
System connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 - 13
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Basic Operation
General control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Setting the clock (Remote control only). . . . . . . . . . . . . . . . . . 16
CD or MP3/WMA disc Playback
To comply with the ENERGY STAR® standards mentioned above,
please cancel the demonstration mode, as described on page 13.
Listening to a CD or MP3/WMA disc . . . . . . . . . . . . . . . . .17 - 19
Advanced CD or MP3/WMA disc playback . . . . . . . . . . . .19 - 21
MP3/WMA Navigation (only for MP3/WMA files) . . . . . . . .22 - 25
Radio
®
ENERGY STAR is a U.S. registered mark.
Listening to the AM/FM stations . . . . . . . . . . . . . . . . . . . .26 - 27
Tape Playback
Special Note
Supply of this product does not convey a license nor imply any right
to distribute content created with this product in revenue-generating
broadcast systems (terrestrial, satellite, cable and/or other
distribution channels), revenue-generating streaming applications
(via Internet, intranets and/or other networks), other revenuegenerating content distribution systems (pay-audio or audio-ondemand applications and the like) or on revenue-generating physical
media (compact discs, digital versatile discs, semiconductor chips,
hard drives, memory cards and the like). An independent license for
such use is required. For details, please visit http://mp3licensing.com
MPEG Layer-3 audio coding technology licensed from Fraunhofer
IIS and Thomson.
Listening to a cassette tape (TAPE 1 or TAPE 2) . . . . . . .28 - 29
Tape Recording
General Information
ENERGY STAR® Program Information
General Information
Recording on a cassette tape . . . . . . . . . . . . . . . . . . . . . . .29 - 31
Advanced Features
Timer and sleep operation (Remote control only). . . . . . .31 - 34
Enhancing your system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
References
Troubleshooting chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 - 37
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 - 39
CONSUMER LIMITED WARRANTY . . . . . . . . . . . . . .Back cover
5
03/12/17
CD-SW340 02-43.fm
CD-SW340
Precautions
General
Please ensure that the equipment is positioned in a well ventilated
area and ensure that there is at least 4" (10 cm) of free space
along the sides, top and back of the equipment.
4" (10 cm)
4" (10 cm)
4" (10 cm)
5
4
3
2
1
TIMER
CD
5
4
3
2
1
PLAYBACK (PLAY & STOP)
General Information
PHONES
RECORD/PLAYBACK
Hold the AC power plug by the head when
removing it from the AC outlet, as pulling
the cord can damage internal wires.
The AC power plug is used as a disconnect
device and shall always remain readily
operable.
Do not remove the outer cover, as this
may result in electric shock. Refer
internal service to your local SHARP
service facility.
AUDIO
IN
4" (10 cm)
Floor
Table
Do not place subwoofer system on the same surface as main
unit to prevent sound interruption during playback.
AC INPUT
This unit should only be used within the range of 41˚F - 95˚F
(5˚C - 35˚C).
Use the unit on a firm, level surface free
from vibration.
5
4
3
2
1
TIMER
5
CD
4
3
2
1
RECORD/PLAYBACK
PLAYBACK
PHONES
(PLAY & STOP)
AUDIO
IN
Keep the unit away from direct sunlight,
strong magnetic fields, excessive dust,
humidity and electronic/electrical
equipment (home computers,
facsimiles, etc.) which generate
electrical noise.
Do not place anything on top of the unit.
Do not expose the unit to moisture, to temperatures higher than
140˚F (60˚C) or to extremely low temperatures.
If your system does not work properly, disconnect the AC power
cord from the AC outlet. Plug the AC power cord back in, and then
turn on your system.
In case of an electrical storm, unplug the
unit for safety.
Warning:
The voltage used must be the same as that specified on this unit.
Using this product with a higher voltage other than that which is
specified is dangerous and may result in a fire or other type of
accident causing damage. SHARP will not be held responsible for
any damage resulting from use of this unit with a voltage other than
that which is specified.
5
4
3
2
1
TIMER
5
CD
4
3
2
1
RECORD/PLAYBACK
PLAYBACK
PHONES
AUDIO
IN
(PLAY & STOP)
Volume control
The sound level at a given volume setting depends on speaker
efficiency, location, and various other factors. It is advisable to avoid
exposure to high volume levels, which occurs while turning the unit
on with the volume control setting up high, or while continually
listening at high volumes. Excessive sound pressure from earphones
and headphones can cause hearing loss.
6
03/12/17
CD-SW340 02-43.fm
Controls and indicators
CD-SW340
TIMER
CD
5
4
3
2
1
PLAYBACK (PLAY & STOP)
PHONES
AUDIO
IN
RECORD/PLAYBACK
Reference page
1. Disc Trays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2. Timer Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
3. Power On/Stand-by Button . . . . . . . . . . . . . . . . . . . . . . . . . 15
4. CD Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5. Tape (1 2) Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
6. Tuner (Band) Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
7. Audio In Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
8. CD or Tape Stop Button . . . . . . . . . . . . . . . . . . . . . . . . 19, 29
9. CD Track Down or Fast Reverse, Tape 2 Rewind,
Tuner Preset Down, Time Down Button 16, 19, 26, 27, 29, 32
10. Tuning Down, Cursor Down Button . . . . . . . . . . . . . . . 22, 26
11. Tape 1 Cassette Compartment . . . . . . . . . . . . . . . . . . . . . . 28
12. Headphone Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
13. Audio In Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
14. Remote Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
15. Volume Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
16. CD Play or Repeat, Tape Play Button . . . . . . . . . . . 17, 20, 28
17. Disc Tray Open/Close Button . . . . . . . . . . . . . . . . . . . . . . . 17
18. Disc Number Select Buttons . . . . . . . . . . . . . . . . . . . . . . . . 17
19. CD Track Up or Fast Forward, Tape 2 Fast Forward,
Tuner Preset Up, Time Up Button . . . . 16, 19, 26, 27, 29, 32
20. Tuning Up, Cursor Up Button . . . . . . . . . . . . . . . . . . . . 22, 26
21. Tape 2 Cassette Compartment . . . . . . . . . . . . . . . . . . . . . . 28
General Information
Front panel
7
03/12/17
CD-SW340 02-43.fm
CD-SW340
Controls and indicators (continued)
Display
General Information
Reference page
1. Disc Number Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2. MP3/WMA Folder Indicator . . . . . . . . . . . . . . . . . . . . . . . . . 22
3. MP3/WMA Title Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . 22
4. MP3 Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5. WMA Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
6. Sleep Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
7. Timer Play Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
8. Timer Recording Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . 32
9. Tape 2 Record Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
10. Total Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
11. Daily Timer Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
12. FM Stereo Mode Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . 26
13. FM Stereo Receiving Indicator . . . . . . . . . . . . . . . . . . . . . . 26
14. Tape Play Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
15. Memory Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
16. Extra Bass Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
17. Disc Repeat Play Indicator . . . . . . . . . . . . . . . . . . . . . . . . . 20
18. Disc Pause Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
19. Disc Play Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3
4
5
6
7
1
8
9
8
Rear panel
Reference page
1. Cooling Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2. AC Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3. FM 75 Ohms Antenna Jack . . . . . . . . . . . . . . . . . . . . . . . . . 12
4. AM Antenna Ground Terminal . . . . . . . . . . . . . . . . . . . . . . 12
5. AM Loop Antenna Terminal . . . . . . . . . . . . . . . . . . . . . . . . . 12
6. Subwoofer Light-up Jack . . . . . . . . . . . . . . . . . . . . . . . . . . 12
7. Speaker Light-up Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
8. Subwoofer Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
9. Front Speaker Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2
03/12/17
CD-SW340 02-43.fm
CD-SW340
Front Speaker
3
1
1. Tweeter
2. Woofer
3. Bass Reflex Duct
4. Speaker Wire
5. Speaker Light-Up Wire
4
5
Subwoofer
1. Subwoofer
2. Bass Reflex Duct
3. Subwoofer Light-Up Wire
4. Speaker Wire
1
2
3
General Information
2
4
9
03/12/17
CD-SW340 02-43.fm
CD-SW340
Controls and indicators (continued)
Remote control
1
General Information
2
8
9
10
13
17
14
18
15
19
20
11
12
21
16
22
23
3
24
4
5
6
7
26
27
25
28
29
Reference page
1. Remote Control Transmitter . . . . . . . . . . . . . . . . . . . . . . . . 14
2. Disc Number Select Buttons . . . . . . . . . . . . . . . . . . . . . . . . 17
3. Clock/Timer Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16, 32
4. Character Input/Disc Direct Search Buttons . . . . . . . . 20, 24
5. Equalizer Mode Select Button . . . . . . . . . . . . . . . . . . . . . . . 15
6. Extra Bass (Surround)/Demo Button . . . . . . . . . . . . . . 13, 15
7. Volume Up and Down Buttons . . . . . . . . . . . . . . . . . . . . . . 15
8. Power On/Stand-by Button . . . . . . . . . . . . . . . . . . . . . . . . . 15
9. CD Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
10. Tuner (Band) Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
11. Tape (1 2) Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
12. Audio In Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
13. Clear/Dimmer Button . . . . . . . . . . . . . . . . . . . . . . . . . . . 15, 21
14. Disc Random Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
15. Disc Stop Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
16. Tape Stop Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
17. Memory Button . . . . . . . . . . . . . . . . . . . . . . . . . . 16, 21, 27, 32
18. Disc Pause Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
19. Disc Play or Repeat Button . . . . . . . . . . . . . . . . . . . . . . 17, 20
20. Tape Play Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
21. Tape 2 Record Pause Button . . . . . . . . . . . . . . . . . . . . . . . 29
22. Tuning Up, Cursor Up Button . . . . . . . . . . . . . . . . . . . . 22, 26
23. Disc Track Up or Fast Forward, Tape Fast Forward,
Tuner Preset Up, Time Up, Cursor Right Button . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16, 19, 26, 27, 29, 32
24. Disc Track Down or Fast Reverse, Tape Fast Rewind,
Tuner Preset Down, Time Down, Cursor Left Button . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16, 19, 26, 27, 29, 32
25. Tuning Down, Cursor Down Button . . . . . . . . . . . . . . . 22, 26
26. MP3/WMA Navigation Mode Select Button . . . . . . . . . . . . 22
27. Character Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
28. MP3/WMA Display Button . . . . . . . . . . . . . . . . . . . . . . . . . . 22
29. Enter Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
10
03/12/17
CD-SW340 02-43.fm
System connections
CD-SW340
Make sure to unplug the AC power cord before making any connections.
Antenna connection (see page 12)
Right speaker
AM loop antenna
Left speaker
Subwoofer
Speaker light-up wire
Speaker light-up wire
Speaker connection
(see page 12)
Preparation for Use
FM antenna
Subwoofer
Light-up wire
AC Outlet
(AC 120 V ~ 60 Hz)
AC power connection (see page 13)
11
03/12/17
CD-SW340 02-43.fm
System connections (continued)
Antenna connection
Preparation for Use
Speaker Light-Up connection
1
Supplied AM loop antenna:
Connect the AM loop antenna to the
AM and GND terminals. Position the
AM loop antenna for optimum
reception. Place the AM loop antenna
on a shelf, etc., or attach it to a stand
or a wall with screws (not supplied).
ANTENNA
FM
GND
AM
75 OHMS
Note:
Placing the antenna on the unit or near the AC power cord may
cause noise pickup. Place the antenna away from the unit for better
reception.
Installing the AM loop antenna:
< Assembling >
< Attaching to the wall >
Wall
Caution:
Never mistake the FRONT SPEAKERS and the SUBWOOFER
terminals. The unit or the speakers may be damaged.
If you use other speakers with an impedance lower than that specified,
the unit may be damaged. Front speakers: 6 ohms, Subwoofer: 12 ohms.
Do not mistake the right and the left channels. The
right speaker is the one on the right side when you
face the unit.
Do not let the bare speaker wires touch each other.
Do not stand or sit on the speakers. You may be
injured.
Do not allow any objects to fall into or to be placed in the
bass reflex duct.
Incorrect
Screws (not supplied)
Speaker connection
12
FRONT SPEAKERS:
Connect the black wire to the
FRONT SPEAKERS minus
(–) terminal, and the red wire
to the FRONT SPEAKERS
plus (+) terminal.
SUBWOOFER:
Connect the black wire to the
SUBWOOFER minus (–)
terminal, and the red wire with
purple insulation tube to the
SUBWOOFER plus (+)
terminal.
Purple
LEFT
Connect the speaker light-up wires to the
SPEAKERS LIGHT-UP jacks for speaker
illumination. To turn off the speaker light-up feature,
press the CLEAR/DIMMER button on the remote
control for 2 seconds or more.
Note:
Placing the right speaker light-up wire to the RIGHT jack and the left
speaker light-up wire to the LEFT jack.
2 Connect the subwoofer light-up wire to the
SUBWOOFER LIGHT-UP jack.
SPEAKERS
LIGHT-UP
AM loop
antenna
FM
antenna
SUB
WOOFER
LIGHT-UP
Supplied FM antenna:
Connect the FM antenna wire to the
FM 75 OHMS jack and position the FM
antenna wire in the direction where the
strongest signal can be received.
RIGHT
CD-SW340
Red
Black
03/12/17
CD-SW340 02-43.fm
CD-SW340
Demonstration mode
Left speaker
Main unit
Right speaker
Subwoofer
TIMER
CD
5
4
3
2
1
PLAYBACK (PLAY & STOP)
PHONES
RECORD/PLAYBACK
AUDIO
IN
Table
Floor
Note:
The speaker grilles are not removable.
AC power connection
After checking all the connections have been made correctly, plug
the AC power cord of this unit into the AC outlet. If you plug in the unit
first, the unit will enter the demonstration mode.
AC outlet
(AC 120 V ~ 60 Hz)
Notes:
The unit will start the tape initialization when plugged in to the AC
outlet. During this process, initializing sound will be heard and the
unit cannot be turned on. Wait until the process is finished.
Unplug the AC power cord from the AC outlet if the unit will not be
in use for a prolonged period of time.
Cooling fan:
The main unit is built with a
cooling fan at the rear of the unit
for improved cooling. Please do
not cover the opening of the fan
with any obstacles, as this will
block proper ventilation.
The first time the unit is plugged in, the
unit will enter the demonstration mode.
You will see words scroll and the
subwoofer and front speaker will light up
in flashing mode.
To cancel the demonstration mode:
When the unit is in the power
stand-by mode (demonstration
mode), press the X-BASS
(SURROUND)/DEMO button. The
unit will enter the low power
consumption mode and the
subwoofer and front speaker light
up will be off.
To return to the demonstration mode:
When the unit is in the power stand-by mode, press the
X-BASS (SURROUND)/DEMO button again.
Note:
When the power is on, the X-BASS (SURROUND)/DEMO button can
be used to select the extra bass mode.
Outdoor FM antenna
Use an outdoor FM antenna if you require better reception. Consult
your dealer.
Preparation for Use
Placing the speaker system
There is no distinction between the right and left speakers.
ANTENNA
FM
GND
AM
Outdoor
FM antenna
75 OHMS
75 ohms
coaxial cable
Note:
When an outdoor FM antenna is used, disconnect the supplied FM
antenna wire.
03/12/17
CD-SW340 02-43.fm
13
CD-SW340
Remote control
Battery installation
Use 2 “AA” size batteries (UM/SUM-3, R6, HP-7 or similar).
Batteries are not included.
1
2
Preparation for Use
3
Open the battery cover.
Insert the batteries according to the direction indicated in
the battery compartment.
When inserting or removing the batteries, push them toward the
battery terminals.
Close the battery cover.
Notes concerning use:
Replace the batteries if the operating distance is reduced or if the
operation becomes erratic.
Periodically clean the transmitter on the remote control and the
sensor on the unit with a soft cloth.
Exposing the sensor on the unit to strong light may interfere with
operation. Change the lighting or the direction of the unit.
Keep the remote control away from moisture, heat, shock, and
vibrations.
Test of the remote control
Check the remote control after checking all the connections (see
pages 11 - 13).
Point the remote control directly at the remote sensor on the unit.
The remote control can be used within the range shown below:
Press the ON/STAND-BY button. Does the power turn on? Now, you
can enjoy the music.
Remote sensor
TIMER
Precautions for battery use:
Replace all old batteries with new ones at the same time.
Do not mix old and new batteries.
Remove the batteries if the unit will not be used for long periods
of time. This will prevent potential damage due to battery leakage.
Batteries (battery pack or batteries installed) shall not be exposed
to excessive heat such as sunshine, fire or the like.
CD
5
4
3
2
1
8" - 20'
(0.2 m - 6 m)
PLAYBACK (PLAY & STOP)
PHONES
RECORD/PLAYBACK
AUDIO
IN
Caution:
Do not use rechargeable batteries (nickel-cadmium battery, etc.).
Installing the batteries incorrectly may cause the unit to
malfunction.
Battery removal:
Open the battery cover and pull up the battery to take out.
14
03/12/17
CD-SW340 02-43.fm
General control
CD-SW340
Volume control
TIMER
CD
5
4
3
2
1
Main unit operation:
When the VOLUME control is turned
clockwise, the volume will increase.
When it is turned counterclockwise, the
volume will decrease.
Remote control operation:
Press the VOLUME (+ or –) button to
increase or decrease the volume.
0 ..... 30 MAXIMUM
Surround mode
X-BASS
Equalizer
To turn the power on
Press the ON/STAND-BY button to turn the power on.
After use:
When the power is first turned on, the unit will enter FLAT mode.
When the EQUALIZER MODE button is pressed, the current mode
setting will be displayed. To change to a different mode, press the
EQUALIZER MODE button repeatedly until the desired sound mode
appears.
Press the ON/STAND-BY button to enter the power stand-by mode.
Illumination light control
FLAT
No equalization.
ROCK
For rock music.
CLASSIC
When the power is turned on, light illuminates around the display.
To turn on/off the light, hold down the CLEAR/DIMMER button on
the remote control for 2 seconds or more.
VOCALS
Subwoofer and front speaker light up control
JAZZ
The subwoofer and front speaker will light up according to the level of
the music source played back. To turn on/off the light, hold down the
CLEAR/DIMMER button on the remote control for 2 seconds or more.
Volume auto fade-in
POPS
Basic Operation
When the X-BASS (SURROUND)/
DEMO button is pressed, the unit will
enter the surround mode and adjust low
bass and high frequency automatically
according to volume input. To cancel this
mode, press the X-BASS (SURROUND)/
DEMO button again.
For classical music.
For Pop music.
Vocals are enhanced.
For Jazz.
Note:
If the EQUALIZER MODE button is pressed in the surround mode, it
will be canceled automatically.
If you turn off and on the main unit with the volume set to 27 or
higher, the volume starts at 16 and fades in to the last set level.
15
03/12/17
CD-SW340 02-43.fm
CD-SW340
Setting the clock (Remote control only)
5
Press the
or
button to adjust the hour and
then press the MEMORY button.
Press the
or
button once to advance the time by
1 hour. Hold it down to advance continuously.
Basic Operation
6
Press the
or
button to adjust the minutes and
then press the MEMORY button.
In this example, the clock is set for the 12-hour (AM 12:00) display.
1
2
3
Press the ON/STAND-BY button to turn the power on.
4
Press the
or
button to select 12-hour or 24hour display and then press the MEMORY button.
Press the CLOCK/TIMER button.
Within 10 seconds, press the
or
button to
select “CLOCK”, and press the MEMORY button.
“AM 12:00”
“AM 0:00”
“0:00”
The 12-hour display will appear.
(AM 12:00 - PM 11:59)
The 12-hour display will appear.
(AM 0:00 - PM 11:59)
The 24-hour display will appear.
(0:00 - 23:59)
Press the
or
button once to advance the time by
1 minute. Hold it down to change the time in 5-minute intervals.
To confirm the time display:
[When the unit is in the stand-by mode]
Press the CLOCK/TIMER button.
The time display will appear for about 10 seconds.
[When the power is on]
Press the CLOCK/TIMER button.
Within 10 seconds, press the
or
button to display the
time.
The time display will appear for about 10 seconds.
Note:
The “CLOCK” will appear or time will flash to confirm the time
display when the AC power supply is restored after a power failure
or unplugging the unit. If incorrect, readjust the clock as follows.
To readjust the clock:
Perform “Setting the clock” from step 1. If the “CLOCK” does not
appear in step 3, step 4 (for selecting the 12-hour or 24-hour
display) will be skipped.
To change the 12-hour or 24-hour display:
1 Clear all the programmed contents. [Refer to “Clearing all the
memory (reset)” on page 37 for details.]
2 Perform “Setting the clock” from step 1 onwards.
16
03/12/17
CD-SW340 02-43.fm
Listening to a CD or MP3/WMA disc
CD-SW340
This system can play back a standard CD, CD-R/RW in the CD
format and CD-R/RW with MP3 or WMA files, but cannot record on
them. Some audio CD-R and CD-RW discs may not be playable due
to the state of the disc or the device that was used for recording.
OPEN/
CLOSE
TIMER
CD
CD
5
4
5
3
2
1
4
3
PLAYBACK (PLAY & STOP)
PHONES
RECORD/PLAYBACK
2
AUDIO
IN
WMA:
WMA files are Advanced System Format files that include audio
files which are compressed with Windows Media Audio codec.
WMA is developed by Microsoft as an audio format file for
Windows Media Player.
“MP3” and “WMA” indicators will light up after the unit reads
information on an MP3 or WMA disc.
1
Auto power on function:
When you press any of the following buttons, the unit turns on.
CD button (main unit and remote control): The unit turns on and
the “CD” function is activated.
CD / button on the remote control: The unit turns on and CD
playback starts (regardless of the last function).
/ button on the main unit: The unit turns on and playback of
the last function starts (CD,TAPE,TUNER,AUDIO IN).
CD or MP3/WMA disc Playback
MP3:
MP3 is a form of compression. It is an acronym which stands
for MPEG Audio Layer 3.
MP3 is a type of audio code which is processed by significant
compression from the original audio source with very little loss
in sound quality.
This system supports MPEG 1 Layer 3, MPEG 2 Layer 3, and
VBR files.
During VBR file playback, time counter in the display may differ
from its actual playback time.
Auto power off function:
In the stop mode of CD, MP3 or WMA operation, the main unit enters
the stand-by mode after 15 minutes of inactivity.
17
03/12/17
CD-SW340 02-43.fm
CD or MP3/WMA disc Playback
CD-SW340
Listening to a CD or MP3/WMA disc (continued)
1
2
3
Press the ON/STAND-BY button to turn the power on.
4
Place the disc on the disc tray 1, label side up.
Be sure to place 3" (8 cm) disc in the middle of the disc trays.
Press the CD button.
Press the 1 button and within 5 seconds, press the
button to open the disc tray 1.
5" (12 cm)
3" (8 cm)
Playback will begin from track 1 on disc 1. After that disc finishes
playing, the next disc will automatically play.
After the last track on the fifth disc is played, the unit will stop
automatically.
When there is no disc in one of the disc trays (1 - 5), the empty
tray will be skipped to the next tray with a disc.
To exchange other discs while playing a disc:
Press one of the 1 - 5 buttons for the stopped disc and within 5
seconds, press the button and exchange discs.
To remove the discs:
In the stop mode, press the
press the button.
5
Press the / button to close the disc tray 1.
MP3 indicator
WMA indicator
[CD]
[MP3/WMA]
Total number of
tracks on the disc
Total playing
time of the disc
Total number Total number
of folders
of files
Due to the structure of the disc information, it takes longer to
read an MP3/WMA disc than a normal CD (approximately 20
to 90 seconds).
6
You can place discs on the trays 2 - 5 by following steps
3 - 5.
7
Press the
/
1-
5 buttons and within 5 seconds,
Caution:
Do not place two discs in a same tray.
Do not play discs of special shapes (heart, octagon, etc.) as it
may cause malfunctions.
Do not push the disc tray while it is moving.
If the power fails while the tray is open, wait until the power is
restored.
If the disc tray is stopped with force, “ER-CD21” will appear on the
display for 3 seconds and the unit will not function. If this occurs,
press the ON/STAND-BY button to enter the power stand-by
mode and then turn the power on again.
If TV or radio interference occurs during CD operation, move the
unit away from the TV or radio.
If a disc is damaged, dirty, or loaded upside down, the disc will
skip or not play.
button to start playback.
Disc play indicator
18
03/12/17
CD-SW340 02-43.fm
Advanced CD or MP3/WMA disc
playback
Function
Play
Main unit
Remote
control
Operation
Press in the stop mode.
Stop
Press in the playback mode.
Pause
Press in the playback mode.
Press the / button to
resume playback from the
paused point.
Track up/
Track
down
Press in the playback or stop
mode.
If you press the button in the
stop mode, press the /
button to start the desired
track.
Fast
forward/
Fast
reverse
Press and hold down in the
playback mode.
Release the button to
resume playback.
Notes for CD or MP3/WMA disc:
Track up/track down is possible only within individual discs.
Fast forward/fast reverse is possible only within individual discs.
When the end of the last track is reached during fast forward,
“END” will appear on the display and CD operation will be paused.
When the beginning of the first track is reached during fast
reverse, the unit will enter the playback mode.
Rewritable multi-session discs which writing is not finished, can
still be played.
To specify a disc to play
You can play a disc by specifying the disc number.
1
Press one of the
2
Within 5 seconds, press the
1-
5 buttons to select the desired disc.
Selected disc number
/
button on the main unit.
TIMER
CD
5
4
3
2
1
Playback will begin from track 1 on the chosen disc.
After the last track on the last disc is played, the unit stops
automatically.
CD or MP3/WMA disc Playback
Various disc functions
CD-SW340
Note:
If a disc tray with no disc is selected, playback will not start and the
disc indicator will disappear.
To stop playback:
Press the (CD ) button.
19
03/12/17
CD-SW340 02-43.fm
CD-SW340
Advanced CD or MP3/WMA disc playback (continued)
Direct track search
By using the direct search buttons, the desired tracks on the current
disc can be played.
CD or MP3/WMA disc Playback
Use the direct search buttons on
the remote control to select the
desired track while playing the
selected disc.
Selected track number
The direct search buttons allow you to select up to number 9.
When selecting number 10 or higher, use the “+10” button.
A. For example, to choose 13
1 Press the “+10” button once.
2 Press the “3” button.
To cancel repeat play:
Press the / button again. “ ” will disappear.
Random play
The tracks on the disc(s) can be played in random order automatically.
To random play all tracks on up to 5 discs:
Press the RANDOM button on the remote control.
B. For example, to choose 130
1 Press the “+10” button three times.
2 Press the “0” button.
Notes:
A track number higher than the number of tracks on the disc
cannot be selected.
During random play, direct search is not possible.
To stop playback:
Press the (CD ) button.
Repeat play
Repeat play can play all 5 discs, all tracks on a chosen disc, or a
programmed sequence continuously.
20
To repeat one disc:
Press the / button twice.
To repeat all tracks on up to 5 discs:
Press the / button three times.
To repeat desired tracks:
Perform steps 1 - 6 in “Programmed play” section on page 21 and
then press the / button twice.
To cancel random play:
Press the / button. “R” will disappear.
Notes:
If you press the
button during random play, you can move to
the next track by the random operation. However, the
button
does not allow you to move to the previous track. It will go to the
beginning of the current track instead.
In random play, the unit will select and play tracks automatically.
(You cannot select the order of the tracks.)
Caution:
After performing repeat or random play, be sure to press the
(CD ) button. Otherwise, the disc(s) will play continuously.
03/12/17
CD-SW340 02-43.fm
CD-SW340
1
2
While in the stop mode, press the
MEMORY button on the remote
control to enter the programming
save mode.
To cancel the programmed play mode:
While in the stop mode and the “MEMORY” indicator is lit, press the
CLEAR/DIMMER button on the remote control. The “MEMORY”
indicator will disappear and all the programmed contents will be
cleared.
Press one of the 1 - 5 buttons
to select the desired disc.
Selected disc number
3
Press the direct search buttons
on the remote control to select
the desired track.
Selected track number
You can also select a track by pressing the
or
button.
4
Press the MEMORY button to
save the track number.
5
Repeat steps 2 - 4 for other tracks. Up to 32 tracks can be
programmed.
If you make a mistake, the programmed tracks can be cleared
by pressing the CLEAR/DIMMER button.
6
Press the
To clear the programmed selections:
Press the CLEAR/DIMMER button on the
remote control while the “MEMORY” indicator
is flashing.
Each time the button is pressed, one track will
be cleared, beginning with the last track
programmed.
Adding tracks to the program:
If a program has been previously stored, the “MEMORY” indicator
will be displayed. Then follow steps 1 - 6 to add tracks. The new
tracks will be stored after the last track of the original program.
To check which tracks are programmed:
While the unit is stopped in the programmed play mode, press the
or
button.
Notes:
When a disc with programmed tracks is ejected, the program is
automatically canceled.
Even if you press the ON/STAND-BY button to enter the stand-by
mode or change the function from CD to another, the programmed
selections will not be cleared.
During the program operation, random play is not possible.
CD or MP3/WMA disc Playback
Programmed play
You can choose up to 32 selections for playback in the order you like.
(CD ) button.
The total number in memory will
appear.
7
Press the
/
button to start playback.
21
03/12/17
CD-SW340 02-43.fm
CD or MP3/WMA disc Playback
CD-SW340
MP3/WMA navigation (only for MP3/WMA files)
MP3/WMA navigation:
You can search and play files by folder or title. For example, when
you assign three titles to a file, enter genre (such as jazz) as title 1,
album name as title 2, and music title as title 3 to search the file by
any title.
You can search and play files by folder or title 1/2/3 within one
MP3/WMA disc (see page 23).
By entering a name, you can search files by folder or title 1/2/3
within one MP3/WMA disc (see page 24).
Folders or titles can be programmed within one MP3/WMA disc
(see page 25).
When you enter file names on your PC, connect words with hyphens.
This product recognizes the first word as title 1, second one as title
2, and third one as title 3. Up to three words can be recognized.
Example:
Folder
Title 1
Title 2
Title 3
(File name)
Folder
Title 1
Title 2
Title 3
AAA
(POPULAR-HITS 1-A MUSIC.mp3)
(POPULAR-HITS 2-B MUSIC.mp3)
BBB
(JAZZ-HITS 1-A MUSIC.mp3)
(JAZZ-HITS 2-B MUSIC.mp3)
CCC
(ROCK-HITS 1-A MUSIC.mp3)
(ROCK-HITS 2-B MUSIC.mp3)
(ROCK-HITS 3-C MUSIC.mp3)
(ROCK-HITS 4-D MUSIC.mp3)
Notes:
MP3 files must have the extension “.mp3”.
WMA files must have the extension “.wma”.
Up to 100 folders or 300 files can be read on the unit. If either limit
is exceeded, no more folders/files are displayed.
This unit recognizes and displays up to 48 characters for folder
names, and up to 32 characters for title 1/2/3.
All file/folder names appear in uppercase.
22
03/12/17
CD-SW340 02-43.fm
CD-SW340
File search (by folder or title 1/2/3)
You can search and play files by folder or title 1/2/3 within one MP3/
WMA disc.
1
Press one of the
1 5 buttons to select a disc tray
containing an MP3/WMA disc.
2
Press the
disc.
3
Press the CD button to stop playback.
“NAVI READ” appears and the display shows the total number
of folders and files on the selected disc.
Use the
or
cursor button to scroll and select a folder
(or title), and then press the ENTER button.
Folder name
button, and the unit starts to read the MP3
If you press the / button instead of the ENTER button, all
files in the selected folder (or title) are played.
8
Use the
or
File name
MP3 indicator
WMA indicator
Total number Total number
of folders
of files
4
5
9
Press the NAVIGATION button.
Press the , ,
or
cursor
button on the remote control to
select “FOL”, “T-1”, “T-2” or “T-3”.
To search files by folder name,
select “FOL” (will flash).
Folder
Title 1
Title 2
Title 3
The following steps describe file search by folder:
6
Press the ENTER button.
The total number of folders (or titles) appears for 2 seconds,
and names of the first 2 folders (or titles) are displayed.
Folder
Folder name
name
The NAVIGATION button allows you to go one step back.
Press the DISPLAY button to
check the number of files.
cursor button to scroll and select a file.
Press the / button to start playback.
The unit plays from the selected file to the last file in the
selected folder (or title), and the previous display returns.
File search by title 1/2/3:
In step 5, select “T-1”, “T-2” or “T-3” and follow the same steps as
file search by folder.
The unit searches all files on the disc, regardless of the folder.
To stop playback:
Press the CD button.
To exit the MP3/WMA navigation mode:
In the stop mode, press the CD button.
CD or MP3/WMA disc Playback
/
7
Notes:
In the MP3/WMA navigation mode, direct play and direct search
functions are disabled.
If a folder, title or file name does not appear, or appears
incorrectly, remove and reinsert the disc and try again.
If you press the RANDOM button in the stop mode, the MP3/WMA
navigation mode will be canceled.
23
03/12/17
CD-SW340 02-43.fm
CD-SW340
MP3/WMA navigation (only for MP3/WMA files) (continued)
Character search (for folder or title 1/2/3)
CD or MP3/WMA disc Playback
By entering a name, you can search files by folder or title 1/2/3 within
one MP3/WMA disc.
1
Perform steps 1 - 3 in “File search (by folder or title 1/2/3)”
on page 23.
2
3
Press the NAVIGATION button.
4
5
6
Press the , ,
or
cursor
button on the remote control to
select “FOL”, “T-1”, “T-2” or
“T-3”. To search files by folder
name, select “FOL” (will flash).
or
or
When finished, press the ENTER button. The unit searches
for the same name within folders (or titles).
If the search word is not in the folder (or title) name, “NOT
FOUND” appears and the menu returns.
Folder
Title 1
Title 2
Title 3
Press the CHARACTER button for 2 seconds.
The display will be ready for editing characters.
1st row: String table
2nd row: Input editor (8 digits)
Press the
alphabet.
Press the
display.
8
cursor button to select the desired
button to go to the next page of character
Press the CHARACTER button and the active character will
be entered in the 2nd row of the display.
9
Use the or
(or title).
10
Press the / button to start playback.
All files in the selected folder (or title) are played, and the
previous display returns.
cursor button to scroll and select a folder
To exit the MP3/WMA navigation mode:
In the stop mode, press the CD button.
Notes:
The unit searches regardless of the case, and names found will
appear in uppercase.
Some symbols do not appear properly.
Character entry with direct buttons:
The direct buttons on the remote
control can also be used for
character entry.
In step 5 on the left, use buttons 0 9 to enter alphabets.
Alphabet types change as you
press a button.
For example, press “2” four times to enter “C”.
To delete an entered character, move the cursor to the
character with the
or
button and press the CLEAR/
DIMMER button on the remote control.
7
Repeat steps 5 and 6 to enter characters.
In the folder (or title) name search, you do not have to enter the
full name. The unit searches for names beginning with the
entered characters.
2
A
B
C
Characters:
1
2 ABC
3 DEF
4 GHI
5 JKL 6 MNO 7 PQRS 8 TUV 9 WXYZ
: indicates a space.
24
03/12/17
CD-SW340 02-43.fm
0
CD-SW340
1
2
3
4
Perform steps 1 - 3 in “File search (by folder or title 1/2/3)”
on page 23.
Press the , , or cursor button on the remote control
to select “FOL”, “T-1”, “T-2” or “T-3” and then press the
ENTER button.
The total number of folders (or titles) appears for 2 seconds,
and names of the first 2 folders (or titles) are displayed.
Press the or cursor button to select the desired folder
(or title) and then press the MEMORY button.
Repeat step 4 for other folders (or titles).
Up to 10 folders (or 10 titles) can be programmed.
6
Flashes if the folder (or title)
is programmed
Press the NAVIGATION button.
The folder (or title) is memorized with all the files.
5
To check, add or delete programmed contents:
In the stop mode, select a folder (or title) with the
or
cursor
button. If the folder (or title) is programmed, “MEMORY” flashes.
Press the
/
button to start playback.
Programmed play will always start from the smallest folder (or
title) number.
When you press the MEMORY button with “MEMORY” flashing,
the folder (or title) is removed from the program.
If you press the MEMORY button with “MEMORY” off, the folder
(or title) is added to the program.
To clear all programs, press the CLEAR/DIMMER button in the
stop mode.
To exit the MP3/WMA navigation mode:
In the stop mode, press the CD button.
The programmed contents are cleared.
Notes:
The programmed contents are cleared when you eject a disc,
play another disc, switch the function, or enter the stand-by mode
with the ON/STAND-BY button.
If you press the RANDOM button in the stop mode, the MP3/
WMA navigation mode will be canceled.
If tracks are programmed using track numbers (see
“Programmed play” on page 21):
In the MP3/WMA navigation mode, only program by folder (or title)
name are played. When you exit the mode, the program by folder (or
title) name are cleared.
When you exit the MP3/WMA navigation mode, program by track
number are canceled.
(Program by track number are cleared when you remove the disc.)
CD or MP3/WMA disc Playback
Programmed play (for folder, title 1/2/3)
Folders or titles can be programmed within one MP3/WMA disc.
Folder, title 1, title 2 and title 3 cannot be programmed together
simultaneously.
To stop playback:
Press the CD button.
The programmed contents are not cleared.
25
03/12/17
CD-SW340 02-43.fm
CD-SW340
Listening to the AM/FM stations
Tuning
POWER
ON/ STAND-BY
1
2
Press the ON/STAND-BY button to turn the power on.
3
Press the TUNING ( or ) button on the remote control
to tune in to the desired station.
TIMER
CD
5
4
TUNER
(BAND)
3
Press the TUNER (BAND) button repeatedly to select the
desired frequency band (FM or AM).
2
1
Manual tuning:
PLAYBACK (PLAY & STOP)
PHONES
RECORD/PLAYBACK
Press the TUNING ( or ) button as many times as required
to tune in to the desired station.
AUDIO
IN
Auto tuning:
Radio
When the TUNING ( or ) button is pressed for more than
0.5 seconds, scanning will start automatically and the tuner
will stop at the first receivable broadcast station.
Notes:
When radio interference occurs, auto scan tuning may stop
automatically at that point.
Auto scan tuning will skip weak signal stations.
To stop the auto tuning, press the TUNING ( or ) button
again.
To receive an FM stereo transmission:
Press the TUNER (BAND) button to select stereo mode and “ST”
indicator will be displayed.
“ ” will appear when an FM broadcast is in stereo.
If the FM reception is weak, press the TUNER (BAND) button to
extinguish the “ST” indicator. The reception changes to
monaural, and the sound becomes clearer.
FM stereo mode indicator
Auto power on function:
When you press any of the following buttons, the unit turns on.
TUNER (BAND) button (main unit and remote control): The unit
turns on and the “TUNER” function is activated.
/ button on the main unit: The unit turns on and playback of
the last function starts (CD,TAPE,TUNER,AUDIO IN).
FM stereo receiving indicator
26
03/12/17
CD-SW340 02-43.fm
CD-SW340
Memorizing a station
1
2
Perform steps 1 - 3 in “Tuning” on page 26.
3
Within 30 seconds, press the PRESET ( or ) button to
select the preset channel number.
Store the stations in memory, in order, starting with preset
channel 1.
4
Press the MEMORY button on remote control to enter the
preset tuning saving mode.
To recall a memorized station
Press the PRESET ( or
select the desired station.
) button for less than 0.5 seconds to
To scan the preset stations
The stations saved in memory can be scanned automatically.
(Preset memory scan)
1 Press the PRESET ( or ) button for more than 0.5 seconds.
The preset number will flash and the programmed stations will be
tuned in sequentially, for 5 seconds each.
2 Press the PRESET ( or ) button again when the desired
station is located.
TIMER
Within 30 seconds, press the MEMORY button on remote
control to store that station in memory.
CD
5
4
3
2
1
Radio
You can store 40 AM and FM stations in memory and recall them at
the push of a button. (Preset tuning)
If the “MEMORY” and preset number indicators disappear
before the station is memorized, repeat the operation from step
2.
5
Repeat steps 1 - 4 to set other stations, or to change a
preset station.
When a new station is stored in memory, the station previously
memorized for that preset channel number will be erased.
Note:
The backup function protects the memorized stations for a few
hours should there be a power failure or the AC power cord
become disconnected.
To erase entire preset memory
1
2
Press the ON/STAND-BY button to enter the stand-by mode.
While pressing down the button and the
button, press
the TUNER (BAND) button until “TUNER CL” appears.
TUNER
(BAND)
27
03/12/17
CD-SW340 02-43.fm
CD-SW340
Listening to a cassette tape (TAPE 1 or TAPE 2)
Before playback:
For playback, use normal or low-noise tapes for
the best sound. (Metal or CrO tapes are not
recommended.)
Do not use C-120 tapes or poor-quality tapes, as
they may cause malfunctions.
Before loading a tape into the cassette compartment,
tighten the slack with a pen or a pencil.
Tape playback
1
2
Open
the
cassette
compartment by pushing
the area marked “ ”.
OPEN/CLOSE
5
CD
4
5
CD
3
PRESET
4
TAPE 1/2
2
3
PRESET
1
2
PRESET
1
AUDIO IN
— VOL.
TUNING
VOL.
TUNING
— VOL.
PUSH EJECT
PUSH EJECT
& STOP)
PLAYBACK (PLAY
RECORD/PLAYBACK
RECORD/PLAYBACK
& STOP)
PLAYBACK (PLAY
RT
PHONES
3
Load a cassette into the
TAPE 1 compartment or
TAPE 2 compartment with
the side to be played
facing toward you.
4
Press the TAPE (1
want to listen to.
5
Press the / (TAPE
start playback.
CD
5
4
MUSIC PORT
5
CD
4
3
PRESET
2
PRESET
1
TUNING
VOL.
TUNING
— VOL.
RECORD/PLAYBACK
PLAYBACK
(PLAY & STOP)
PHONES
TAPE 1
TIMER
PRESET
TUNER(BAND)
TUNING
VOL.
TUNING
PHONES
POWER
ON/ STAND-BY
Tape Playback
Press the ON/STAND-BY button to turn the power on.
TAPE 2
2) button to select the cassette you
3
2
1
PLAYBACK (PLAY & STOP)
PHONES
PRESET
AUDIO
IN
RECORD/PLAYBACK
PRESET
) to
Tape play indicator
Auto power on function:
When you press any of the following buttons, the unit turns on.
TAPE (1 2) button (main unit and remote control): The unit turns
on and the “TAPE” function is activated.
TAPE button (remote control): The unit turns on and the “TAPE”
function is activated.
/ button (main unit): The unit turns on and playback of the last
function starts (CD,TAPE,TUNER,AUDIO IN).
Auto power off function:
In the stop mode of tape operation, the main unit enters the stand-by
mode after 15 minutes of inactivity.
28
03/12/17
CD-SW340 02-43.fm
Recording on a cassette tape
Main unit
Remote
control
Operation
Playback
Press in the stop
mode.
Stop
Press in the playback,
fast forward or rewind
mode.
Fast
forward/
Rewind
(TAPE 2
only)
Press in the playback
or stop mode.
Before recording:
When recording important selections, make a preliminary test to
ensure that the desired material is properly recorded.
SHARP is not liable for damage or loss of your recording arising
from malfunction of this unit.
The volume and sound controls can be adjusted with no effect
on the recorded signal (Variable Sound Monitor).
For recording, use only normal tapes. Do not use metal or
CrO tapes.
Erase-prevention tab of cassette tapes:
When recording on a cassette tape, make sure that the eraseprevention tabs are not removed. Cassettes have removable
tabs that prevent accidental recording or erasing.
To protect the recorded sound, remove the tab after recording.
Cover the tab hole with adhesive tape to record on the tape
without the tab.
Caution:
To remove the cassette, press the (TAPE ) button, and then
open the compartment.
Before changing from one tape operation to another, press the
(TAPE ) button.
If a power failure occurs during tape operation, the tape head will
remain engaged with the tape and the cassette door will not open.
In this case, wait until the power is restored.
Side A
Tab for side B
Tape Recording
Various tape functions
Function
CD-SW340
Tab for side A
29
03/12/17
CD-SW340 02-43.fm
CD-SW340
Recording on a cassette tape (continued)
To stop recording:
Press the (TAPE ) button.
The disc and tape will stop.
To perform programmed recording:
1 Program discs and tracks (see page 21).
2 Press the
button.
3 Press the / (TAPE ) button to start recording.
POWER
ON/ STAND-BY
OPEN/
CLOSE
CD
TIMER
CD
5
5
4
3
2
4
1
To stop recording:
Press the (TAPE ) button.
The disc and tape will stop.
3
PLAYBACK (PLAY & STOP)
PHONES
RECORD/PLAYBACK
2
AUDIO
IN
Tape Recording
1
Recording from the radio
Recording from a CD or MP3/WMA disc
1
2
3
4
Press the ON/STAND-BY button to turn the power on.
Press the CD button.
Load a cassette into the TAPE 2 cassette compartment
with the side to be recorded on facing you.
Wind past the leader of the tape, on which recording cannot be
performed.
Press the
3
Tune in to the desired station (see page 26).
Load a cassette into the TAPE 2 cassette compartment
with the side to be recorded on facing you.
Wind past the leader of the tape, on which recording cannot be
performed.
Press the
button.
Recording will be paused.
button.
4
Recording will be paused.
5
6
1
2
Press one of the
1-
5 buttons to select the desired disc.
Within 5 seconds, press the
/
button to start recording.
Recording is started from the selected disc. When the
playback of the last track is finished or the end of the tape is
reached, the disc and the cassette will stop automatically.
Playback of the disc will start approximately 7 seconds after
the tape starts.
Press the
/
(TAPE
) button to start recording.
To interrupt recording:
Press the
button.
To resume recording, press the
/
(TAPE
) button.
To stop recording:
Press the (TAPE ) button.
Note:
If you hear a whistling noise while recording an AM station, move the
AM loop antenna.
30
03/12/17
CD-SW340 02-43.fm
Timer and sleep operation
(Remote control only)
Dubbing from tape to tape
You can record from TAPE 1 to TAPE 2.
Press the ON/STAND-BY button to turn the power on.
Load a prerecorded
into the TAPE 1
compartment. Insert
tape into the TAPE 2
compartment.
cassette
cassette
a blank
cassette
5
CD
4
3
PRESET
2
PRESET
1
TUNING
VOL.
TUNING
— VOL.
RECORD/PLAYBACK
PLAYBACK
This unit has 2 types of timer: ONCE TIMER and DAILY TIMER.
(PLAY & STOP)
PHONES
TAPE 1
TAPE 2
It is recommended that the recording tape is the same length as
the master tape.
3
Press the TAPE (1
the display.
4
Press the
button.
Recording will be paused.
5
Press the
/
2) button until “TAPE 1” appears on
(TAPE
3
4
Once timer play or once timer recording works for
one time only at a preset time.
For example, if you are away but want to record a program on a
radio station.
Daily timer play or daily timer recording works at
the same preset time every day.
For example, set the timer as a wake-up call every morning.
) button to start dubbing.
Erasing recorded tapes
2
Once timer:
Daily timer:
To stop dubbing:
Press the (TAPE ) button.
TAPE 1 and TAPE 2 will stop simultaneously.
1
Timer playback:
The unit turns on and plays the desired source (CD, tuner, tape) at a
preset time.
Timer recording:
The unit turns on and starts recording from the tuner at the preset
time.
Load the tape to be erased into the TAPE 2 cassette
compartment with the side to be erased facing toward you.
Press the TAPE (1 2) button until “TAPE 2” appears on the
display.
Press the
button.
Press the / (TAPE ) button to start erasing.
Note:
Make sure that the TAPE 1 is not in use.
Using the once timer and daily timer in combination:
For example, use the once timer to record a radio program, and use
the daily timer to wake up.
1
2
Set the daily timer (pages 32 - 33).
Set the once timer (pages 32 - 33).
Advanced Features
1
2
CD-SW340
1 minute or more
Once timer
Daily timer
Start
Stop
Start
Stop
Note:
When set times for the daily timer and once timer overlap, the once
timer takes priority. Allow an interval of at least 1 minute between
operations.
31
03/12/17
CD-SW340 02-43.fm
CD-SW340
Timer and sleep operation (Remote control only) (continued)
5
or
button to select “PLAY” or
Press the
“REC”, and press the MEMORY button.
White
Red
The illustrations show the daily timer setting.
Advanced Features
6
Press the
or
button to adjust the hour and
then press the MEMORY button.
Timer playback or timer recording
Before setting timer:
1 Check that the clock is set to the correct time (refer to page 16).
If it is not set, you cannot use the timer function.
2 For timer playback: Load a cassette or discs to be played.
For timer recording: Load a cassette for recording in the
cassette compartment.
1
2
3
Press the ON/STAND-BY button to turn the power on.
Press the CLOCK/TIMER button.
Within 10 seconds, press the
or
button to select
“ONCE” or “DAILY”, and press the MEMORY button.
Set the clock to the correct time if “ONCE” or “DAILY” does not
appear.
4
Within 10 seconds, press the
or
button to
select “ONCE SET” or “DAILY SET”, and press the
MEMORY button.
The illustrations show the timer playback setting in the daily
timer mode.
7
or
button to adjust the minutes and
Press the
then press the MEMORY button.
8
9
Set the time to finish as in steps 6 and 7 above.
Switch input with the
or
button, and then
press the MEMORY button.
To select the timer playback source: CD, TUNER, TAPE 1 or
TAPE 2.
To select the timer recording source: TUNER.
When you select the tuner, select a station by pressing the
or
button, and then press the MEMORY
button.
If a station has not been programmed, “NO PRESET” will
be displayed and timer setting will be canceled.
32
03/12/17
CD-SW340 02-43.fm
CD-SW340
Adjust the volume using the VOLUME control, and then
press the MEMORY button.
Do not turn the volume up too high.
11
Press the ON/STAND-BY button to enter the power standby mode.
The “TIMER” indicator lights up and the unit is ready for timer
playback or timer recording.
TIMER
CD
5
4
3
2
1
12
When the preset time is reached, playback or recording
will start.
The volume will increase gradually until it reaches the preset
volume.
13
When the timer end time is reached, the system will enter
the power stand-by mode automatically.
Once timer:
The timer will be canceled.
The “r” indicator will blinking during timer playback.
Daily timer:
The timer will operate at the same time every day. It will
continue until the daily timer setting is canceled. Cancel the
daily timer when it is not used.
The “DAILY r” indicator will blinking during timer playback.
Note:
When performing timer playback or recording using another unit
connected to the AUDIO IN jack, select “AUDIO IN” in step 9.
This unit will turn on or enter the power stand-by mode automatically,
however, the connected unit will not turn on or off.
Checking the timer setting in the timer stand-by mode:
1 Press the CLOCK/TIMER button.
2 Within 10 seconds, press the
or
button to select
“ONCE” or “DAILY”, and press the MEMORY button.
3 Within 10 seconds, press the
or
button to select
“ONCE CALL” or “DAILY CALL”, and press the MEMORY button.
The unit returns to the timer stand-by mode after displaying the
settings in order.
Canceling the timer setting in the timer stand-by mode:
1 Press the CLOCK/TIMER button.
2 Within 10 seconds, press the
or
button to select
“ONCE” or “DAILY”, and press the MEMORY button.
3 Within 10 seconds, press the
or
button to select
“ONCE OFF” or “DAILY OFF”, and press the MEMORY button.
Timer will be canceled (the setting will not be canceled).
Reusing the memorized timer setting:
The timer setting will be memorized once it is entered. To reuse the
same setting, perform the following operations.
1 Turn the power on and press the CLOCK/TIMER button.
2 Within 10 seconds, press the
or
button to select
“ONCE” or “DAILY”, and press the MEMORY button.
3 Within 10 seconds, press the
or
button to select
“ONCE ON” or “DAILY ON”, and press the MEMORY button.
4 Press the ON/STAND-BY button to enter the power stand-by
mode.
Advanced Features
10
33
03/12/17
CD-SW340 02-43.fm
CD-SW340
Timer and sleep operation (Remote control only) (continued)
Sleep operation
The radio, CD, MP3/WMA disc and cassette tape can all be turned
off automatically.
Advanced Features
1
2
3
4
Play back the desired sound source.
Press the CLOCK/TIMER button.
Within 10 seconds, press the
or
button to select
“SLEEP”, and press the
MEMORY button.
Press the
or
button to select the time.
(Maximum: 3 hours - Minimum: 1 minute)
3 hours - 5 minutes 5-minute intervals
5 minutes - 1 minute 1-minute intervals
5
Press the MEMORY button.
“SLEEP” will appear.
6
The unit will enter the power stand-by mode automatically
after the preset time has elapsed.
The volume will be turned down 1 minute before the sleep
operation finishes.
To confirm the remaining sleep time:
1 While “SLEEP” is indicated, press the CLOCK/TIMER button.
2 Within 10 seconds, press the
or
button to select
“SLEEP X : XX”.
“X : XX” is remaining sleep time.
The remaining sleep time is displayed for about 10 seconds.
You can change the remaining sleep time while it is displayed by
pressing the MEMORY button. (Steps 4 - 5)
To cancel the sleep operation:
Press the ON/STAND-BY button while “SLEEP” is indicated.
To cancel the sleep operation without setting the unit to the stand-by
mode, proceed as follows.
1 While “SLEEP” is indicated, press the CLOCK/TIMER button.
2 Within 10 seconds, press the
or
button to select
“SLEEP OFF”, and press the MEMORY button.
To use timer and sleep operation together
Sleep and timer playback:
For example, you can fall asleep listening to the radio and wake up
to CD in the next morning.
Sleep and timer recording:
For example, you can fall asleep listening to the CD and record radio
programs while sleeping.
1
2
Set the sleep time (see left, steps 1 - 5).
While the sleep timer is set, set the timer playback or recording
(steps 2 - 10, pages 32 - 33).
Sleep timer setting
Timer playback or
recording setting
1 minute - 3 hours
Sleep operation will
automatically stop
End time
Desired time
Timer playback or recording
start time
Caution:
When using the cassette deck, be sure the tape length is long
enough to perform both functions. If you want to sleep and wake up
listening to a tape, and the length of the tape is shorter than the sleep
timer setting, timer playback or recording will not be possible.
34
03/12/17
CD-SW340 02-43.fm
Enhancing your system
The connection cord is not included. Purchase a commercially
available cord as shown below.
Portable audio
player, etc.
CD-SW340
Auto power on function:
When you press any of the following buttons, the unit turns on.
AUDIO IN button (main unit and remote control): The unit turns
on and the “AUDIO IN” function is activated.
/ button on the main unit: The unit turns on and playback of
the last function starts (CD,TAPE,TUNER,AUDIO IN).
To record sounds of Portable Audio Player, etc.
CD
5
4
3
2
1
PLAYBACK (PLAY & STOP)
PHONES
RECORD/PLAYBACK
AUDIO
IN
1
2
3
4
5
Insert a cassette in the TAPE 2 cassette compartment.
Press the AUDIO IN button.
Press the
Press the
button.
/
button.
Play the Portable Audio Player, etc.
Headphones
Audio cable
(not supplied)
Listening to sounds of Portable Audio Player,
etc.
1
Connect a Portable Audio Player etc. to the front AUDIO IN
jack.
2
3
4
Press the ON/STAND-BY button to turn the power on.
Before plugging in or unplugging the headphones, reduce the
volume.
Be sure your headphones have a 1/8" (3.5 mm) diameter plug and
impedance between 16 and 50 ohms. The recommended
impedance is 32 ohms.
Plugging in the headphones disconnects the speakers
automatically. Adjust the volume using the VOLUME control.
Advanced Features
TIMER
To the line output jack
TIMER
Press the AUDIO IN button.
CD
5
4
3
2
Play the connected equipment.
1
You can enjoy sounds from the supplied speakers.
PLAYBACK (PLAY & STOP)
Note:
To prevent noise interference, place the unit away from the television.
PHONES
RECORD/PLAYBACK
AUDIO
IN
35
03/12/17
CD-SW340 02-43.fm
CD-SW340
Troubleshooting chart
Many potential problems can be resolved by the owner without
calling a service technician.
If something is wrong with this product, check the following before
calling your authorized SHARP dealer or service center.
General
References
Symptom
The clock is not set to the
correct time.
When a button is pressed,
the unit does not respond.
No sound is heard.
Possible cause
Did a power failure occur? Reset
the clock. (Refer to page 16.)
Set the unit to the power standby mode and then turn it back on.
If the unit still malfunctions, reset
it. (Refer to page 37.)
Is the volume level set to “0”?
Are the headphones connected?
Are the speaker wires
disconnected?
Playback sounds are
skipped, or stopped in the
middle of a track.
Symptom
Cannot record.
Cannot record tracks with
proper sound quality.
Cannot erase completely.
Sound skipping.
Cannot hear treble.
Sound fluctuation.
Cannot remove the tape.
Possible cause
Is the erase-prevention tab
removed?
Is it a normal tape? (You cannot
record on a metal or CrO tape.)
Is there any slack?
Is the tape stretched?
Are the capstans, pinch rollers,
or heads dirty?
If a power failure occurs during
playback, the heads remain
engaged with the tape. Do not
open the compartment with great
force.
Remote control
CD player
Symptom
Playback does not start.
Playback stops in the
middle or does not
perform properly.
Cassette deck
Possible cause
Is the disc loaded upside down?
Does the disc satisfy the
standards?
Is the disc distorted or
scratched?
Is the unit located near excessive
vibrations?
Is the disc very dirty?
Has condensation formed inside
the unit?
Symptom
The remote control does
not operate.
Possible cause
Is the AC power cord of the unit
plugged in?
Is the batteries polarity correct?
Are the batteries dead?
Is the distance or angle
incorrect?
Does the remote control sensor
receive strong light?
36
03/12/17
CD-SW340 02-43.fm
CD-SW340
Tuner
Clearing all the memory (reset)
Possible cause
Is the unit placed near the TV or
computer?
Is the FM antenna or AM loop
antenna placed properly? Move
the antenna away from the AC
power cord if it is located nearby.
Condensation
Sudden temperature changes, storage or operation in an extremely
humid environment may cause condensation inside the cabinet (CD
pickup, tape heads, etc.) or on the transmitter on the remote control.
Condensation can cause the unit to malfunction. If this happens,
leave the power on with no disc (or cassette) in the unit until normal
playback is possible (about 1 hour). Wipe off any condensation on
the transmitter with a soft cloth before operating the unit.
If problem occurs
When this product is subjected to strong external interference
(mechanical shock, excessive static electricity, abnormal supply
voltage due to lightning, etc.) or if it is operated incorrectly, it may
malfunction.
If such a problem occurs, do the following:
1 Set the unit to the stand-by mode and turn the power on again.
2 If the unit is not restored in the previous operation, unplug and
plug in the unit, and then turn the power on.
Note:
If neither operation above restores the unit, clear all the memory by
resetting it.
1
2
Press the ON/STAND-BY button to enter the power stand-by
mode.
While pressing down the button and the button, press the CD
button until “CLEAR ALL” appears.
CD
Caution:
This operation will erase all data stored in memory including clock,
timer settings, tuner preset, and CD program.
Before transporting the unit
Remove all CDs from the unit. Make sure there is no CD in the disc
tray. Then, set the unit to the power stand-by mode. Carrying the unit
with discs left inside can damage the unit.
Care of compact discs
Compact discs are fairly resistant to damage, however mistracking
can occur due to an accumulation of dirt on the disc surface. Follow
the guidelines below for maximum enjoyment from your CD
collection and player.
Do not write on either side of the disc, particularly the non-label
side from which signals are read. Do not mark this surface.
Keep your discs away from direct sunlight, heat, and excessive
moisture.
Always hold the CDs by the edges. Fingerprints, dirt, or water on
the CDs can cause noise or mistracking. If a CD is dirty or does
not play properly, clean it with a soft, dry cloth, wiping straight out
from the center, along the radius.
NO
References
Symptom
The radio makes unusual
noises continuously.
YES
Correct
37
03/12/17
CD-SW340 02-43.fm
CD-SW340
Maintenance
Specifications
Cleaning the tape-handling parts
Dirty heads, capstans or pinch rollers can cause poor sound and
tape jams. Clean these parts with a cotton swab moistened with
commercial head/pinch roller cleaner or isopropyl alcohol.
When cleaning the heads, pinch rollers, etc., unplug the unit which
contains high voltages.
A
TAPE 1
B
General
C
5
4
3
2
1
TIMER
5
CD
4
3
D
2
E B
C
1
TAPE 2
RECORD/PLAYBACK
RECORD/PLAYBACK
(PLAY
PLAYBACK (PLAY
PLAYBACK
References
PHONES
STOP)
&& STOP)
AUDIO
IN
Playback head
Capstans
Pinch rollers
As part of our policy of continuous improvement, SHARP reserves
the right to make design and specification changes for product
improvement without prior notice. The performance specification
figures indicated are nominal values of production units. There may
be some deviations from these values in individual units.
Erase head
Recording/Playback head
Power source
AC 120 V ~ 60 Hz
Power consumption 195 W
Dimensions
Width: 10-1/4" (260 mm)
Height: 13" (332 mm)
Depth: 12-7/8" (324 mm)
Weight
21.6 lbs. (9.8 kg)
Amplifier
Output power
After long use, the deck's heads and capstans may become
magnetized, causing poor sound. Demagnetize these parts once
every 30 hours of playing/recording time by using a commercial
tape head demagnetizer. Read the demagnetizer's instructions
carefully before use.
Cleaning the CD pickup lens
In order to ensure proper operation of the CD player, preventative
maintenance (cleaning of the laser pickup lens) should be performed
periodically. Lens cleaners are commercially available. Contact your
local CD software dealer for options.
Output terminals
Cleaning the cabinet
Periodically wipe the cabinet with a soft cloth and a diluted soap
solution, then with a dry cloth.
Input terminals
38
Caution:
Do not use chemicals for cleaning (gasoline, paint thinner, etc.). It
may damage the cabinet finish.
Do not apply oil to the inside of the unit. It may cause
malfunctions.
03/12/17
Front Speakers RMS: Total 250 W (125
watts per channel into 6 ohms at 1 KHz, 10%
Total harmonic distortion.)
Front Speakers FTC: 100 watts minimum
RMS per channel into 6 ohms from 100 Hz to
20 KHz, 10% Total harmonic distortion.
Subwoofer RMS: 250 watts into 12 ohms at
100 Hz, 10% total harmonic distortion.
Subwoofer FTC: 200 watts RMS into 12
ohms from 50 Hz to 120 Hz, 10% Total
harmonic distortion.
Front Speakers: 6 ohms
Subwoofer: 12 ohms
Headphones: 16 - 50 ohms
(recommended: 32 ohms)
AUDIO IN (audio signal):
500 mV/ 47 k ohms
AUDIO IN: 1Vp-p
CD-SW340 02-43.fm
CD-SW340
CD player
D/A converter
Frequency
response
Dynamic range
5-disc multi-play compact disc player
Non-contact, 3-beam semiconductor laser
pickup
Multi bit D/A converter
20 - 20,000 Hz
90 dB (1 kHz)
Type
Maximum input
power
Rated input power
Impedance
Dimensions
Tuner
Frequency range
FM: 87.5 - 108.0 MHz
AM: 530 - 1,720 kHz
Wow and flutter
125 W
6 ohms
Width: 7-7/8" (200 mm)
Height: 13" (330 mm)
Depth: 8 - 11/16" (220.5 mm)
7.0 lbs. (3.18 kg) /each
Subwoofer
Cassette deck
Frequency
response
Signal/noise ratio
Weight
2-way type speaker system
2" (5 cm) tweeter
6-5/16" (16 cm) woofer
250 W
50 - 14,000 Hz (normal tape)
Type
55 dB (TAPE 1, playback)
50 dB (TAPE 2, recording/playback)
0.3 % (WRMS)
Maximum input
power
Rated input power
Impedance
Dimensions
Weight
Subwoofer system
8" (20 cm) subwoofer
500 W
References
Type
Signal readout
Front Speaker
250 W
12 ohms
Width: 9-13/16" (250 mm)
Height: 13" (330 mm)
Depth: 11-5/16" (288 mm)
12.9 lbs. (5.85 kg)
39
03/12/17
CD-SW340 02-43.fm
CONSUMER LIMITED WARRANTY
SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the Product ), when ship ped in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective Product or part thereof
with a new or remanufactured equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below.
This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth below nor to any Product the exterior of which has
been damaged or defaced, which has been subjected to improper voltage or other misuse, abnormal service or handling, or which has been altered or modified in
design or construction.
In order to enforce the rights under this limited warranty, the purchaser should follow the steps set forth below and provide proof of purchase to the servicer.
The limited warranty described herein is in addition to whatever implied warranties may be granted to purchasers by law. ALL IMPLIED WARRANTIES INCLUDING
THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE ARE LIMITED TO THE PERIOD(S) FROM THE DATE OF PURCHASE SET FORTH BELOW.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those described herein, or to extend the duration of any
warranties beyond the time period described herein on behalf of Sharp.
The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and exclusive remedy available to the purchaser.
Correction of defects, in the manner and for the period of time described herein, shall constitute complete fulfillment of all liabilities and responsibilities of Sharp to the
purchaser with respect to the Product, and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise. In no event
shall Sharp be liable, or in any way responsible, for any damages or defects in the Product which were caused by repairs or attempted repairs performed by anyone
other than an authorized servicer. Nor shall Sharp be liable or in any way responsible for any incidental or consequential economic or property damage. Some states
do not allow the exclusion of incidental or consequential damages, so the above exclusion may not apply to you.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
Model Specific Section
Your Product Model Number & Description:
CD-SW340 Mini Component System
(Be sure to have this information available when you need service for your Product.)
Warranty Period for this Product:
One (1) year parts and labor from the date of purchase.
Additional Item(s) Excluded from Warranty Coverage (if any): Non-functional accessories, supplies, and consumable items.
Where to Obtain Service:
At a Sharp Authorized Servicer located in the United States.
To find a location of the nearest Sharp Authorized Servicer, call Sharp toll free at 1-800-BE-SHARP.
What to do to Obtain Service:
Ship prepaid or carry in your Product to a Sharp Authorized Servicer.
Be sure to have Proof of Purchase available. If you ship the Product, be sure it is insured and
packaged securely.
TO OBTAIN SUPPLY, ACCESSORY OR PRODUCT INFORMATION, CALL 1-800-BE-SHARP.
0311
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07430
03/11/4
CD-SW340_BACK.fm
Printed in Malaysia
TINSEA230AWZZ
08B R KI 1