Shop fox W1792 Owner`s manual

MODEL W1791/W1792
MINI HVLP SPRAY GUN
W1791
W1792
OWNER'S MANUAL
Phone: (360) 734-3482 • Online Technical Support: tech-support@shopfox.biz
COPYRIGHT © JUNE, 2007 BY WOODSTOCK INTERNATIONAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
#9612TR PRINTED IN CHINA
�����������������������������������������������������������������������
��������������������������������������������������������������
����������������������������������������������������������������������
��������������������������������������������������������������������
������������������������
�����������������������������������������������������������������������
������������������������������������������������������������������������
�������������������������������������������������������������������
�����������������������������������������������������������������
����������������������������������������������������������������������
�����������������������������������������������
����������������������������������������������������������������
��������������������������������������������������������������������
�������
��������������������������������������������������������������������
�����������������������������������������������������������������������
����������������������������������������������������������������������
�������������������������������������
�� ����������������������������
�� ������������������������������������������������������������������
�� ����������������������������������������������������
������������������������������������������������������������������
������������������������������������������������������������������
��������������������������������������������������������������������
���������������������������������������������������������������������
��������������������������
Model W1791/W1792 Mini HVLP Spray Gun
SAFETY
For Your Own Safety Read Instruction Manual
Before Operating This Equipment
The purpose of safety symbols is to attract your attention to possible hazardous
conditions. This manual uses a series of symbols and signal words which are intended
to convey the level of importance of the safety messages. The progression of
symbols is described below. Remember that safety messages by themselves do not
eliminate danger and are not a substitute for proper accident prevention measures.
Indicates an imminently hazardous situation which, if
not avoided, WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if
not avoided, COULD result in death or serious injury.
Indicates a potentially hazardous situation which, if
not avoided, MAY result in minor or moderate injury.
It may also be used to alert against unsafe practices.
NOTICE
This symbol is used to alert the user to useful
information about proper operation of the
equipment.
Safety Instructions for Pneumatic Tools
5. KEEP CHILDREN AND VISITORS
AWAY. All children and visitors
should be kept at a safe distance
from work area.
1. KEEP ALL SAFETY DEVICES IN
PLACE and in working order.
2. REMOVE ADJUSTING KEYS AND
WRENCHES. Form habit of checking
to see that keys and adjusting
wrenches are removed from tool
before operation.
6. MAKE WORKSHOP CHILD PROOF by
locking your shop and shutting off
air valves.
7. DO NOT FORCE TOOL. It will do
the job better and safer at the rate
for which it was designed.
3. KEEP WORK AREA CLEAN. Cluttered
areas and benches invite accidents.
4. DO NOT USE IN DANGEROUS
ENVIRONMENT. Do not use
pneumatic tools in damp or wet
locations, or where any flammable
or noxious fumes may exist. Keep
work area well lighted.
8. USE THE RIGHT TOOL. Do not
force tool or attachment to do a
job for which it was not designed.
9. DO NOT USE UNDER THE
INFLUENCE OF DRUGS OR
ALCOHOL.
-1-
Model W1791/W1792 Mini HVLP Spray Gun
Safety Instructions for Pneumatic Tools
10. USE PROPER AIR HOSE for the
tool. Make sure your air hose is in
good condition and is long enough
to reach your work without
stretching.
17. DISCONNECT TOOLS before
servicing, changing accessories, or
moving to another location.
11. WEAR PROPER APPAREL. Do
not wear loose clothing, gloves,
neckties, rings, bracelets, or
other jewelry which may get
caught in moving parts. Non-slip
footwear is recommended. Wear a
protective hair covering to contain
long hair.
19. USE THE RECOMMENDED
ACCESSORIES. Consult owner’s
manual for recommended
accessories. The use of improper
accessories may cause risk of
injury.
18. DO NOT OVERREACH. Keep proper
footing/balance at all times.
20. CHECK FOR DAMAGED PARTS
BEFORE USING. Check for binding
and alignment of parts, broken
parts, part mounting, loose bolts,
and any other conditions that
mayaffect tool operation. Repair
or replace damaged parts.
12. ALWAYS USE SAFETY GLASSES.
Also use a face or dust mask
if cutting operation is dusty.
Everyday eyeglasses only have
impact resistant lenses, they are
NOT safety glasses.
21. NEVER LEAVE UNATTENDED TOOL
CONNECTED TO AIR. Disconnect
the air hose and do not leave tool
until it is relieved of any built up
pressure.
13. WEAR APPROVED HEARING
PROTECTION. Air escaping from
pneumatic tools can exceed safe
exposure limits and may cause
hearing damage with prolonged
exposure.
22. NEVER ALLOW UNTRAINED
USERS TO USE THIS TOOL WHILE
UNSUPERVISED.
14. SECURE WORK. Use clamps or a
vise to hold work when practical.
It is safer than using your hand
and frees both hands to operate
tool.
23. IF YOU ARE UNSURE OF THE
INTENDED OPERATION, STOP
USING TOOL. Seek formal training
or research books or magazines
that specialize in pneumatic tools.
15. MAINTAIN TOOLS WITH CARE.
Keep tools lubricated and clean
for best and safest performance.
Follow instructions for lubricating
and changing accessories.
24. BE AWARE OF HOSE LOCATION
WHEN USING PNEUMATIC TOOLS.
Hoses can easily become a tripping
hazard when laid across the floor
or spread out in a disorganized
fashion.
16. REDUCE THE RISK OF
UNINTENTIONAL FIRING. Do not
carry tool with hand on trigger
and always disconnect from air
when not in use.
-2-
Model W1791/W1792 Mini HVLP Spray Gun
Additional Safety Instructions for Spray Guns
1.
READ THIS MANUAL. This manual
contains proper operating
instructions for this spray gun.
2.
READ MATERIAL LABELS and
MATERIAL SAFETY DATA SHEETS
(MSDS). Read and know all the
instructions on the packaging label
and the MSDS before opening the
package. This information could
save your life.
3.
ALWAYS WEAR A NIOSH
APPROVED RESPIRATOR WHEN
SPRAYING OR WORKING AROUND
FINISHING MATERIALS.
4.
FIRE EXTINGUISHERS. Always
have a fully charged multi class
or class B fire extinguisher in the
immediate area.
5.
FLAMMABLE MATERIAL. NEVER
spray near open flame or where
any spark could occur.
6.
FRESH AIR. Always provide
adequate exhaust to keep area
free of built up vapors, NEVER
spray in an enclosed space.
7.
DISCONNECT COMPRESSED AIR.
Always disconnect the spray
gun from compressed air before
cleaning, changing attachments or
when performing maintenance of
any kind on this tool.
8.
PROTECTIVE CLOTHING. Protect
exposed skin from overspray by
wearing a protective suit or other
approved garment.
9.
UNSAFE USE. DO NOT point
or shoot spray gun directly at
yourself or another person or
animals. Do not attempt to use
the spray gun for any other use
than it was intended.
10. STORAGE. Thoroughly clean and
dry spray gun before storage.
Store in an approved cabinet.
11. SOLVENTS. Always store solvents
and shop towels soaked in solvent
in approved containers.
12. EYE PROTECTION. Wear eye
protection whenever spraying or
cleaning. Solvents and chemicals
can cause serious eye injury,
which could lead to blindness.
13. OPERATING PRESSURE. DO NOT
exceed the recommended inlet air
pressure. Excessive pressure could
cause the spray gun to burst or
cause other internal equipment
damage.
14. LOCAL LAWS. Consult local
authorities regarding exhaust and
waste disposal requirements.
No list of safety guidelines can be complete. Every shop environment is different.
Always consider safety first, as it applies to your individual working conditions. Use
this and other tools with caution and respect to avoid serious injury.
-3-
Model W1791/W1792 Mini HVLP Spray Gun
INTRODUCTION
Woodstock Technical
Support
W1791 Specifications
Type....................... HVLP Gravity Feed
Fluid Tip ............................... 0.8 mm
Air Consumption ...................3.5–6 CFM
Inlet Air Pressure ..... 3-4 Bar /43.5-58 PSI
Fluid Pressure ..............Less Than 10 PSI
Pattern Width ...................110–160 mm
Material Capacity ..................... 100 ml
This tool has been specially designed to
provide many years of trouble-free service. Close attention to detail, ruggedly
built parts and a rigid quality control program assure safe and reliable operation.
Woodstock International, Inc. is committed to customer satisfaction. Our intent
with this manual is to include the basic
information for safety, setup, operation,
maintenance, and service of this product.
W1792 Specifications
Type....................... HVLP Gravity Feed
Fluid Tip ............................... 0.8 mm
Air Consumption ....................... 6 CFM
Inlet Air Pressure ..... 3-4 Bar /43.5-58 PSI
Fluid Pressure ..............Less Than 10 PSI
Pattern Width ...................110–160 mm
Material Capacity ..................... 120 ml
We stand behind our tools! In the
event that questions arise about
your tool, please contact Woodstock
International Technical Support at
(360) 734-3482 or send e-mail to:
tech-support@shopfox.biz. Our knowledgeable staff will help you troubleshoot
problems and process warranty claims.
If you need the latest edition of this
manual, you can download it from
http://www.shopfox.biz.
If you have comments about this
manual, please contact us at:
Woodstock International, Inc.
Attn: Technical Documentation
Manager
P.O. Box 2309
Bellingham, WA 98227
Email: manuals@woodstockint.com
Read manual before operation.
Become familiar with spray gun and
its safety and operation instructions
before beginning any work. Serious
personal injury may result if safety
or operational information is not
understood or followed.
-4-
Model W1791/W1792 Mini HVLP Spray Gun
SETUP
Unpacking
This tool has been carefully packaged for safe transportation. If you notice the tool
has been damaged during shipping, please contact your authorized Shop Fox dealer
immediately.
Inventory
The following is a description of the main components shipped with the Model W1791/
W1792. Lay the components out to inventory them.
Note: If you can't find an item on this list, check the mounting location on the tool
or examine the packaging materials carefully. Occasionally we pre-install certain
components for safer shipping.
Qty
W1791 Inventory (Figure 1)
A. Spray Gun ................................ 1
B. Cup 100 ml ............................... 1
C. Cleaning Brush........................... 1
D. Service Wrench .......................... 1
E. Filters ..................................... 2
F. Barbed Hose Fitting .................... 1
G. Lock Nut .................................. 1
H. Air Regulator ............................ 1
W1792 Inventory (Figure 2)
Qty
A. Spray Gun ................................ 1
B. Cup 120 ml ............................... 1
C. Cleaning Brush........................... 1
D. Service Wrench .......................... 1
E. Filters ..................................... 2
F. Barbed Hose Fitting .................... 1
G. Lock Nut .................................. 1
E
B
D
C
A
D
E
C
B
G
A
G
H
F
F
Figure 1. Model W1791 inventory.
Figure 2. Model W1792 inventory.
-5-
Model W1791/W1792 Mini HVLP Spray Gun
Controls
Assembly
1.
Insert the filter into the gun body
(see Figure 3).
Atomizing Cap
Cup
Fluid Control
Trigger
Air Flow Control
Pattern
Control
Regulator/Gauge
Figure 4. Controls (W1791 shown).
1.
Fluid Control: Controls the volume
of material that travels through the
fluid tip.
Figure 3. Installing filter.
2.
Screw the cup onto the top of the
body.
2.
3.
Install the barbed hose fitting into
the base of the gun handle and tighten in place with the lock nut.
Pattern Control: Adjusts the spray
pattern from a round pattern to a
wide fan.
3.
Air Flow Control: Controls the fluid
pressure inside the spray gun.
Secure the air hose to the barbed fitting with a hose clamp.
4.
Atomizing Cap: Controls the spray
pattern from vertical to horizontal.
5.
Trigger: Two stage trigger. Stage
one only releases compressed air for
blowing off the work piece. Stage two
sprays material.
6.
Material Cup: Holds the paint to be
sprayed.
7.
Regulator/Gauge (W1791 Only): Regulates inlet air pressure to the spray
gun. It can be attached directly to the
gun for on-the-spot air adjustments
or directly from the air source.
4.
Note: Using a 1⁄4" NPS quick disconnect set-up (not included), will make
operation and maintenance tasks easier.
5.
Attach the spray gun to an air hose
regulated between 43.5 and 58 PSI.
Note: For the best results, use a hose
that will be dedicated for spray use
only. Do not use a hose that has been
used with an in-line oiler or other
possible contaminant.
Note: DO NOT attach to an unregulated air source that exceeds 120 PSI.
-6-
Model W1791/W1792 Mini HVLP Spray Gun
OPERATIONS
Spraying
The Model W1791/W1792 HVLP spray
gun is designed to spray low to medium
viscosity materials, such as lacquers,
stains, primers, multi-component paints,
acrylics, epoxies etc. It is ideal for auto
body touch-ups, woodworking projects,
or projects with hard to reach areas.
It is not for use with any water-based
material.
EXPLOSION HAZARD! DO NOT smoke
or have any source of flame or spark
near spraying. Vapors will explode if
ignited.
To use your spray gun:
1. Read and follow the material
manufacturer's instructions for
spraying, mixing, safety, disposal,
and any other instruction on the label
or Material Safety Data Sheet (MSDS).
2. Ensure the cup is securely tightened
and all other fittings are secure to
avoid air leaks or material spills.
RESPIRATORY HAZARD! Always use
respirator rated for organic vapor and
solvent use when using spray equipment. Failure to protect your lungs
can lead to respiratory illness and
nervous system damage.
3. Set the inlet air pressure (the air
coming to the spray gun) to the
lowest pressure recommended
in Specifications on Page 4 or
to the material manufacturer's
recommendations (not to exceed 58
PSI).
4. Adjust the atomizing cap to vertical
or horizontal. See Atomizing Cap
and Fan Adjustments on Page 9 for
further explanation.
5. Fill the cup with material.
TOXIC FUMES! Always use an approved
spray booth or well ventilated area
when spraying. NEVER spray in an
confined space where toxic fumes
and flammable vapors can accumulate to deadly levels.
-7-
6. Trial and error are necessary to
achieve the results you want along
with a fair amount of practice. Test
your material flow and spray pattern
on a piece of cardboard or some
scrap of material similar to your
project.
Model W1791/W1792 Mini HVLP Spray Gun
7. Adjust the fluid control knob to
start with a low volume of material
and keep the atomization as low
as possible. You will need to use a
combination of fluid control, inlet air
pressure, air flow control and stroke
speed to achieve the results you
want. Spray so the material wets out
nicely without running or sagging.
10. Begin spraying 2-3 inches before the
work and continue to the end of the
work. Continue the motion for a few
inches past the work until you are
ready for the return stroke.
11. Maintain an even speed when
spraying.
��
��
12. Overlap each stroke by 50%. This will
ensure even coverage as shown in
Figure 6. Overlapping less than 50%,
as shown in the figure to the right,
may lead to missed spots or streaky
results.
8. Use the pattern control knob to
adjust the spray fan to your desired
pattern.
9. Keep the gun tip perpendicular,
parallel, and 6-8" from the work (as
shown in Figure 5) when spraying.
Do not allow your wrist to bend. This
will cause the gun to arc across the
surface and distribute the material
unevenly, possibly creating sags and
dry spots.
Yes
��
��
No
Figure 6. Overlap technique.
13. Spray stroke should have even
consistency and parallel edges.
If it doesn't, please refer to
Troubleshooting on Page 12.
NOTICE
Figure 5. Spray technique.
Tipping spray gun may cause material
to spill out of the cup. Always hold
the spray gun perpendicular to the
ground to avoid potential spills and
gravity feed problems.
-8-
Model W1791/W1792 Mini HVLP Spray Gun
Atomizing Cap and Fan
Adjustments
Rotating the pattern adjustment control
in Figure 8 will give you a range between
the two patterns in Figure 9.
The atomizing cap needs to be adjusted
for horizontal or vertical spraying
patterns. Spraying in the wrong direction
may lead to material build up on the
atomizing cap horn. Many performance
problems are caused by clogged
atomizing holes on the atomizing cap
horns (see Cleaning on Page 10).
Stroke
Pattern
Pattern Control
Figure 8. Set up for horizontal spray
stroke with vertical fan pattern.
Pattern
Stroke
Pattern Control
Figure 7. Set up for vertical stroke direction with horizontal fan pattern.
Figure 9. Fan adjustment.
-9-
Model W1791/W1792 Mini HVLP Spray Gun
CLEANING & LUBRICATION
Cleaning
5. Unscrew the atomizing cap with
your fingers and the fluid tip with
the service wrench. The fully
disassembled gun should look like
Figure 10.
Proper cleaning is the best way to ensure
trouble free performance from your spray
gun. If your gun is not thoroughly cleaned,
damage and poor spraying will result.
Problems caused by improper cleaning will
not be covered by the warranty. Clean the
spray gun immediately after each use.
6. Rinse these parts thoroughly in
solvent then dry with compressed air
or let air dry.
Note: If the small holes in the
atomizing cap become blocked, soak
in clean solvent. If the blockage
still exists, clear the blockage with
a small needle, taking great care
to not enlarge or damage the hole.
Damage to the hole will create a
disrupted spray pattern.
To clean your spray gun:
1. Spray a small amount of solvent
through the spray gun.
Note: Check with local laws
regarding this practice. If you are
spraying on a regular basis, spraying
solvents into the air may be illegal. A
cabinet style spray gun cleaner may
be required.
7. Use the cleaning brush with solvent
to clean the inner orifice and other
hard to reach areas on the outside of
the spray gun body.
2. DISCONNECT SPRAY GUN FROM AIR!
8. Wipe the rest of the gun body with a
shop towel and dry.
3. Unscrew the cup.
4. Disassemble the gun by unscrewing
the fluid control knob, removing the
spring and needle (Figure 10).
EXPLOSION HAZARD! Chlorinated
Solvents like Tricloroethane and
Methylene Chloride (methyl chloride)
can chemically react with aluminum
and may explode. Many parts in spray
guns are made of aluminum. Read
solvent label carefully before using
solvent.
Cup
Strainer
Fluid Tip
Needle
Atomizing
Cap
Spring
Fluid
Control
Knob
NOTICE
Figure 10. Disassembly for cleaning.
DO NOT soak the spray gun body
in solvent. Prolonged exposure to
solvent will rapidly deteriorate the
spray gun washers and seals. Ignoring
this notice will void your warranty.
-10-
Model W1791/W1792 Mini HVLP Spray Gun
Lubrication
Lubricate the following areas with
spray gun lube after cleaning:
A.
B.
C.
D.
E.
F.
A
Atomizing Cap Threads
Air Valve Packing
Trigger Pin
Air Flow Control Valve
Pattern Control
Fluid Control Knob
F
B
C
E
D
After each cleaning, apply a thin film
of petroleum jelly to the needle spring
before reassembling.
Figure 11. Lubrication points.
-11-
Model W1791/W1792 Mini HVLP Spray Gun
Troubleshooting
Symptom
Possible Cause
Possible Solution
Fluttering or
Spitting spray.
1. Dry or worn fluid tip seat
permits air to seep into fluid
passage.
2. Material level too low.
3. Fluid tip or strainer obstructed.
4. Dry needle packing.
1. Tighten fluid tip or replace
seat with new one.
1. Atomizing cap holes are
obstructed.
2. Build-up on top or bottom of
fluid tip.
3. Build-up on atomizing cap is
on needle seat.
1. Clear holes.
1. Left or right side horn holes
are plugged.
2. Build-up on left or right side
of fluid tip.
3. Build-up of material inside
atomizing cap.
1. Clear holes.
1. The material flow exceeds
the atomizing cap capacity.
2. Inlet air pressure is too low.
3. Material is too thick.
1. Lower fluid flow.
1. Volume control turned in too
far.
2. Inlet air pressure too high.
1. Increase volume.
3. Fluid pressure is too low.
3. Increase fluid pressure.
4. Material is too thin.
4. Adjust material.
1. No pressure at gun.
2. Fluid passages dirty.
1. Check air supply.
2. Clean gun, remove any
obstructions.
3. Open.
4. Refill.
Uneven top or bottom pattern.
Right or left arc
pattern.
Heavy deposit of
material in center.
Narrow center pattern.
No spray output.
3. Fluid control closed.
4. Out of paint.
-12-
2. Add material.
3. Clean.
4. Lubricate needle.
2. Clean.
3. Clean.
2. Clean.
3. Clean.
2. Increase inlet air pressure.
3. Thin material.
2. Reduce inlet air pressure.
Model W1791/W1792 Mini HVLP Spray Gun
Symptom
Possible Cause
Possible Solution
Excessive overspray.
1. Fluid pressure too high.
2. Gun is too far from surface.
1. Reduce fluid pressure.
2. Keep gun at recommended
distance.
3. Slow down and maintain
consistent, even parallel
stroke.
3. Spraying too fast.
1. Pattern adjustment screw is
not seating properly.
2. Atomizing cap is loose.
1. Clean or replace.
Runs and sags.
1. Damaged seal.
1. Replace damaged seals.
Material leaks from
cup.
1. Cap not secure.
2. Cup not tight on gun body.
3. Leaking from cap vent hole.
1. Tighten.
2. Tighten.
3. Hold gun upright do not
tilt.
Material leaks from
gun.
1. Fluid tip loose.
2. Dry or damaged seals.
3. Excessive pressure.
1. Tighten.
2. Replace seals.
3. Reduce pressure.
Thick dimpled finish aka "Orange
Peel."
1. Holding gun too close to surface.
2. Inlet air pressure too low.
3. Material not properly mixed.
1. Spray at recommended distance.
2. Check inlet air pressure.
3. Follow manufacturer's
instructions.
4. More surface prep is
required.
Unable to control
spray fan.
4. Surface is dirty or oily.
Dry Spray.
1. Inlet air pressure too high.
2. Gun too far from surface.
3. Gun stroke too fast.
2. Tighten atomizing cap.
1. Lower inlet air pressure.
2. Keep gun at recommended
distance.
3. Slow down and maintain
consistent even parallel
stroke.
Gun leaks from
fluid tip.
1. Debris will not let the needle
seat with the fluid tip.
1. Clean or replace both.
Contaminated
paint.
1. Water or oil in the air line.
1. Install an in-line air filter.
2. Replace air line.
-13-
Model W1791/W1792 Mini HVLP Spray Gun
W1791 PARTS LIST
��
�� �� ��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
�
�
� ��
�
��
�� �� ��
��
��
�� �� �� ��
�� ��
�� �� ��
�
��
��
��
��
��
��
��
�
�
��
REF PART�# DESCRIPTION
REF PART�# DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
X1791001
X1791002
X1791003
X1791004
X1791005
X1791006
X1791007
X1791008
X1791009
X1791010
X1791011
X1791012
X1791013
X1791014
X1791015
X1791016
X1791017
X1791018
X1791019
X1791020
X1791021
X1791022
X1791023
X1791024
X1791025
AIR�ADJUST�SCREW
AIR�ADJUST�KNOB
O-RING�2.5�X�2.1
DOMED�SEAL�WASHER
AIR�ADJUST�SPRING
AIR�INLET�VALVE
SWITCH�SPRING
AIR�INLET�VALVE�ASS'Y
BUBBLE�WASHER
O-RING�4.9�X�1.5
SWITCH�KNOB
SWITCH�WASHER
LOCK�SCREW
AIR�CAP�NUT
AIR�CAP�WASHER
AIR�CAP
STEEL�BALL�
O-RING�17�X�1.5
FLUID�NOZZLE
FLUID�NOZZLE�WASHER
DIRECTION�SCREW
ADJUST�NEEDLE�WASHER
SPECIAL�WASHER
COMPRESSION�SPRING
TRIGGER�PIN�I
-14-
��
X1791026
X1791027
XPEC01M
X1791029
X1791030
X1791031
X1791032
X1791033
X1791034
X1791035
X1791036
X1791037
X1791038
X1791039
X1791040
X1791041
X1791042
X1791043
X1791044
X1791045
X1791046
X1791047
X1791048
X1791049
X1791050
TRIGGER�PIN�II
TRIGGER
E-CLIP�3MM
CUP�100ML
JOINT�NUT
FILTER
FLUID�INLET�JOINT
CUP�LID
SMALL�JOINT�NUT
FLUID�NEEDLE
FLUID�NEEDLE�SPRING
JOINT�CAP
FLUID�ADJUST�KNOB
FLAT�HD�SCR�M2.5-.45�X�8
PATTERN�ADJUST�JOINT�CAP
PATTERN�ADJUST�SCREW
O-RING�2�X�1.5
E-CLIP�2.5MM
PATTERN�ADJUST�KNOB
GUN�BODY
AIR�INLET�JOINT
AIR�REGULATOR
CLEANING�BRUSH
SERVICE�WRENCH
COMPLETE�O-RING�KIT
Model W1791/W1792 Mini HVLP Spray Gun
W1792 PARTS LIST
��
�� �� ��
��
��
��
��
��
��
��
��
��
��
��
��
��
�
�
��
�� �� ��
��
��
�� �� �� ��
�� ��
�� �� ��
� ��
�
�
��
��
��
��
��
��
��
�
�
��
REF PART�# DESCRIPTION
REF PART�# DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
48
49
50
X1791001
X1791002
X1791003
X1791004
X1791005
X1791006
X1791007
X1791008
X1791009
X1791010
X1791011
X1791012
X1791013
X1791014
X1791015
X1791016
X1791017
X1791018
X1791019
X1791020
X1791021
X1791022
X1791023
X1791024
X1791025
AIR�ADJUST�SCREW
AIR�ADJUST�KNOB
O-RING�2.5�X�2.1
DOMED�SEAL�WASHER
AIR�ADJUST�SPRING
AIR�INLET�VALVE
SWITCH�SPRING
AIR�INLET�VALVE�ASS'Y
BUBBLE�WASHER
O-RING�4.9�X�1.5
SWITCH�KNOB
SWITCH�WASHER
LOCK�SCREW
AIR�CAP�NUT
AIR�CAP�WASHER
AIR�CAP
STEEL�BALL�
O-RING�17�X�1.5
FLUID�NOZZLE
FLUID�NOZZLE�WASHER
DIRECTION�SCREW
ADJUST�NEEDLE�WASHER
SPECIAL�WASHER
COMPRESSION�SPRING
TRIGGER�PIN�I
-15-
��
X1791026
X1791027
XPEC01M
X1792029
X1791030
X1791031
X1791032
X1792033
X1791034
X1791035
X1791036
X1791037
X1791038
X1791039
X1791040
X1791041
X1791042
X1791043
X1791044
X1791045
X1791046
X1791048
X1791049
X1791050
TRIGGER�PIN�II
TRIGGER
E-CLIP�3MM
CUP�120ML
JOINT�NUT
FILTER
FLUID�INLET�JOINT
CUP�LID
SMALL�JOINT�NUT
FLUID�NEEDLE
FLUID�NEEDLE�SPRING
JOINT�CAP
FLUID�ADJUST�KNOB
FLAT�HD�SCR�M2.5-.45�X�8
PATTERN�ADJUST�JOINT�CAP
PATTERN�ADJUST�SCREW
O-RING�2�X�1.5
E-CLIP�2.5MM
PATTERN�ADJUST�KNOB
GUN�BODY
AIR�INLET�JOINT
CLEANING�BRUSH
SERVICE�WRENCH
COMPLETE�O-RING�KIT
WARRANTY AND RETURNS
Woodstock International, Inc. warrants all Shop Fox machinery to be free of defects
from workmanship and materials for a period of two years from the date of original
purchase by the original owner. This warranty does not apply to defects due directly
or indirectly to misuse, abuse, negligence or accidents, lack of maintenance, or
reimbursement of third party expenses incurred.
Woodstock International, Inc. will repair or replace, at its expense and at its option,
the Shop Fox machine or machine part which in normal use has proven to be defective,
provided that the original owner returns the product prepaid to a Shop Fox factory
service center with proof of their purchase of the product within two years, and
provides Woodstock International, Inc. reasonable opportunity to verify the alleged
defect through inspection. If it is determined there is no defect, or that the defect
resulted from causes not within the scope of Woodstock International Inc.'s warranty,
then the original owner must bear the cost of storing and returning the product.
This is Woodstock International, Inc.'s sole written warranty and any and all warranties
that may be implied by law, including any merchantability or fitness, for any particular
purpose, are hereby limited to the duration of this written warranty. We do not
warrant that Shop Fox machinery complies with the provisions of any law or acts. In
no event shall Woodstock International, Inc.'s liability under this warranty exceed the
purchase price paid for the product, and any legal actions brought against Woodstock
International, Inc. shall be tried in the State of Washington, County of Whatcom. We
shall in no event be liable for death, injuries to persons or property or for incidental,
contingent, special or consequential damages arising from the use of our products.
Every effort has been made to ensure that all Shop Fox machinery meets high quality
and durability standards. We reserve the right to change specifications at any time
because of our commitment to continuously improve the quality of our products.
Warranty Registration
Name ___________________________________________________________________________________
Street __________________________________________________________________________________
City _________________________ State ___________________________Zip ________________________
Phone # ______________________ Email __________________________Invoice # ___________________
Model #_________Serial #______________Dealer Name__________________Purchase Date___________
CUT ALONG DOTTED LINE
The following information is given on a voluntary basis. It will be used for marketing purposes to help us
develop better products and services. Of course, all information is strictly confidential.
1.
How did you learn about us?
_____ Advertisement
_____ Mail Order Catalog
2.
How long have you been a woodworker/metalworker?
_____ 0-2 Years
_____ 2-8 Years
____ 8-20 Years
_____ 20+ Years
3.
How many of your machines or tools are Shop Fox?
_____ 0-2
_____ 3-5
____ 6-9
_____ 10+
4.
Do you think your tool represents a good value?
_____ Yes
____ No
5.
Would you recommend Shop Fox products to a friend?
_____ Yes
____ No
6.
What is your age group?
_____ 20-29
_____ 50-59
7.
What is your annual household income?
_____ $20,000-$29,000
____ $30,000-$39,000
_____ $50,000-$59,000
____ $60,000-$69,000
8.
Which of the following magazines do you subscribe to?
____
____
____
____
____
____
____
____
____
____
9.
Cabinet Maker
Family Handyman
Hand Loader
Handy
Home Shop Machinist
Journal of Light Cont.
Live Steam
Model Airplane News
Modeltec
Old House Journal
____ Friend
____ Website
____ Local Store
____ Other:
____ 30-39
____ 60-69
____
____
____
____
____
____
____
____
____
____
Popular Mechanics
Popular Science
Popular Woodworking
Practical Homeowner
Precision Shooter
Projects in Metal
RC Modeler
Rifle
Shop Notes
Shotgun News
____ 40-49
____ 70+
____ $40,000-$49,000
____ $70,000+
____
____
____
____
____
____
____
____
____
Today’s Homeowner
Wood
Wooden Boat
Woodshop News
Woodsmith
Woodwork
Woodworker West
Woodworker’s Journal
Other:
Comments:__________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
___________________________________________________________________
___________________________________________________________________
FOLD ALONG DOTTED LINE
Place
Stamp
Here
WOODSTOCK INTERNATIONAL INC.
P.O. BOX 2309
BELLINGHAM, WA 98227-2309
FOLD ALONG DOTTED LINE
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
Download PDF
Similar pages
Woodstock SHOP FOX W1801 Owner`s manual
Woodstock W1802 User's Manual
Woodstock SHOP FOX W1798 Owner`s manual
Woodstock D3276 User's Manual
Woodstock SHOP FOX W1774 Owner`s manual