Item No. _______________________________ PH61 Shake Freezer Four Flavor, Pump Features Offer four separate shake flavors: chocolate, vanilla, strawberry and an optional flavor. Portion controlled shake dispensing for high volume milkshake production. Provides a daily heating and cooling cycle to safely maintain dairy products up to two weeks before a complete disassembly and cleaning is required. Freezing Cylinder One, 7 quart (6.6 liter). Mix Hopper One, 20 quart (18.9 liter). Refrigerated to maintain mix below 41ºF (5ºC). Indicator Lights Mix Low light flashes to alert the operator to add mix. When the Mix Out light flashes, the unit automatically goes into Standby mode to prevent damage. Electronic Controls Viscosity is continually measured to serve consistent quality shakes. The LCD (Liquid Crystal Display) readout will identify temperatures in the hopper or freezing cylinder at any point of operation. History of temperatures and times during the last 13 heat cycles may be viewed. Standby During long no-use periods, the standby feature maintains safe product temperatures in the mix hopper and freezing cylinder. Syrup System Shake flavors are selected from touch pads. Self-contained air compressor delivers shake syrup from three, 1 gallon (3.8 l) syrup tanks located in the lower front compartment. Frozen shake mix and syrup automatically blends to dispense the chosen flavor. Use only single strength syrup, free from pulp and seeds. Rockton, Illinois 61072 800-255-0626 Phone 815-624-8333 Fax 815-624-8000 www.taylor-company.com e-mail: info@taylor-company.com International Office Taylor Company S.r.l. Roma, Italy Tel: +39-06-420-12002 Fax: +39-06-420-12034 e-mail: romeoff@taylor-company.com PH61 Heat Treatment System PH61 PH61Shake Freezer Weights Net Crated Volume lbs. 608 650 cu. ft. 66.5 kgs. 275.8 294.8 cu. m. 1.88 Dimensions Width Depth Height Floor Clearance in. 18-7/16 35-1/4 59-1/2 7-1/2 mm. 468 895 1511 191 Specifications Electrical One dedicated electrical connection is required. See the Electrical chart for the proper electrical requirements. Manufactured to be permanently connected. Consult your local Taylor distributor for cord & receptacle specifications as local codes allow. Beater Motor One, 1.0 HP Refrigeration System One, 11,000 BTU/hr. R404A. (BTUs may vary depending on compressor used.) *Mounted on standard casters Electrical Air Cooled Maximum Fuse Size Minimum Circuit Ampacity Poles (P) Wires (W) Minimum Clearance: 6” (152 mm) on all sides. Minimum air clearances must be met to assure adequate air flow for optimum performance. 208-230/60/3 Air 25 19 3P 4W Water Cooled 208-230/60/3 Water 25 18 3P 4W Water inlet and drain connections under side of base 3/8” FPT. 220-240/50/3 Air 25 18 3P 4W 380-415/50/3N~ Air 20 16 4P 5W This unit may be manufactured in other electrical characteristics. Refer to the local Taylor Distributor for availability. (For exact electrical information, always refer to the data label of the unit.) Options Bidding Specs Electrical: Volt ___________________ Hz__________ ph _________ Neutral: Yes No Faucet Hopper Locks Shake Cup Dispenser Cooling: Air Water NA Options:_________________________________________________ _________________________________________________________ Continuing research results in steady improvements; therefore, these specifications are subject to change without notice. Taylor Company, A Division of Carrier Commercial Refrigeration, Inc. Rockton, Illinois 61072 815-624-8333 800-255-0626 Fax 815-624-8000 www.taylor-company.com Printed in U.S.A. 046338-ADV 2/06