Draytek Vigor2830 Series Installation guide

i
Vigor2830 Series Quick Start Guide
Vigor2830 Series Quick Start Guide
ii
Vigor2830 Series
ADSL2/2+ Security Firewall
Quick Start Guide
Version: 1.0
Firmware Version: V3.3.6_RC1
Date: 12/08/2010
iii
Vigor2830 Series Quick Start Guide
Copyright Information
Copyright
Declarations
Copyright 2010 All rights reserved. This publication contains information that is
protected by copyright. No part may be reproduced, transmitted, transcribed,
stored in a retrieval system, or translated into any language without written
permission from the copyright holders.
Trademarks
The following trademarks are used in this document:
z
Microsoft is a registered trademark of Microsoft Corp.
z
Windows, Windows 95, 98, Me, NT, 2000, XP and Explorer are
trademarks of Microsoft Corp.
z
Apple and Mac OS are registered trademarks of Apple Computer Inc.
z
Other products may be trademarks or registered trademarks of their
respective manufacturers.
Safety Instructions and Approval
Safety
Instructions
Warranty
z
z
Read the installation guide thoroughly before you set up the router.
The router is a complicated electronic unit that may be repaired only be
authorized and qualified personnel. Do not try to open or repair the router
yourself.
z
Do not place the router in a damp or humid place, e.g. a bathroom.
z
Do not stack the routers.
z
The router should be used in a sheltered area, within a temperature range
of +5 to +40 Celsius.
z
Do not expose the router to direct sunlight or other heat sources. The
housing and electronic components may be damaged by direct sunlight or
heat sources.
z
Do not deploy the cable for LAN connection outdoor to prevent electronic
shock hazards.
z
Keep the package out of reach of children.
z
When you want to dispose of the router, please follow local regulations on
conservation of the environment.
We warrant to the original end user (purchaser) that the router will be free from
any defects in workmanship or materials for a period of two (2) years from the
date of purchase from the dealer. Please keep your purchase receipt in a safe
place as it serves as proof of date of purchase. During the warranty period, and
upon proof of purchase, should the product have indications of failure due to
faulty workmanship and/or materials, we will, at our discretion, repair or replace
the defective products or components, without charge for either parts or labor, to
whatever extent we deem necessary tore-store the product to proper operating
condition. Any replacement will consist of a new or re-manufactured
functionally equivalent product of equal value, and will be offered solely at our
discretion. This warranty will not apply if the product is modified, misused,
tampered with, damaged by an act of God, or subjected to abnormal working
conditions. The warranty does not cover the bundled or licensed software of
other vendors. Defects which do not significantly affect the usability of the
product will not be covered by the warranty. We reserve the right to revise the
manual and online documentation and to make changes from time to time in the
contents hereof without obligation to notify any person of such revision or
changes.
Be a Registered
Owner
Web registration is preferred. You can register your Vigor router via
http://www.draytek.com.
Firmware & Tools
Updates
Due to the continuous evolution of DrayTek technology, all routers will be
regularly upgraded. Please consult the DrayTek web site for more information on
newest firmware, tools and documents.
http://www.draytek.com
Vigor2830 Series Quick Start Guide
iv
European Community Declarations
Manufacturer:
Address:
Product:
DrayTek Corp.
No. 26, Fu Shing Road, HuKou County, HsinChu Industrial Park, Hsin-Chu, Taiwan 303
Vigor2830 Series Router
DrayTek Corp. declares that Vigor2830 Series of routers are in compliance with the following essential
requirements and other relevant provisions of R&TTE Directive 1999/5/EEC.
The product conforms to the requirements of Electro-Magnetic Compatibility (EMC) Directive
2004/108/EEC by complying with the requirements set forth in EN55022/Class B and EN55024/Class B.
The product conforms to the requirements of Low Voltage (LVD) Directive 2006/95/EEC by complying
with the requirements set forth in EN60950-1.
Regulatory Information
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one of the following measures:
z
Reorient or relocate the receiving antenna.
z
Increase the separation between the equipment and receiver.
z
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
z
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device may accept any interference received, including interference that may cause undesired
operation.
http://www.draytek.com/user/AboutRegulatory.php
This product is designed for the DSL, ISDN, POTS, and 2.4GHz/5GHz WLAN network throughout the EC
region and Switzerland with restrictions in France. Please see the user manual for the applicable networks
on your product.
v
Vigor2830 Series Quick Start Guide
Vigor2830 Series Quick Start Guide
vi
Table of Contents
1. Introduction........................................................................................................... 1
1.1 Panel Explanation ...................................................................................................................... 2
1.1.1 For Vigor2830 ............................................................................................................... 2
1.1.2 For Vigor2830n ............................................................................................................. 4
1.1.3 For Vigor2830Vn ........................................................................................................... 6
1.1.4 For Vigor2830VS........................................................................................................... 8
1.1.6 For Vigor2830VSn....................................................................................................... 10
1.2 Package Content...................................................................................................................... 12
2. Installing Your Router......................................................................................... 13
2.1 Hardware Installation................................................................................................................ 13
2.2 Printer Installation..................................................................................................................... 15
3. Configuring Web Pages ..................................................................................... 21
3.1 Accessing Web Page ............................................................................................................... 21
3.2 Basic Configuration .................................................................................................................. 22
3.3 Wireless Configuration ............................................................................................................. 30
3.3.1 Basic Wireless LAN Concept ...................................................................................... 30
3.3.2 General Setup ............................................................................................................. 31
3.3.3 Security Settings ......................................................................................................... 32
4. Trouble Shooting ................................................................................................ 35
4.1 Checking If the Hardware Status Is OK or Not......................................................................... 35
4.2 Checking If the Network Connection Settings on Your Computer Is OK or Not ...................... 36
4.3 Pinging the Router from Your Computer .................................................................................. 38
4.4 Checking If the ISP Settings are OK or Not ............................................................................. 39
4.5 Backing to Factory Default Setting If Necessary...................................................................... 39
4.6 Contacting Your Dealer ............................................................................................................ 40
vii
Vigor2830 Series Quick Start Guide
Vigor2830 Series Quick Start Guide
viii
1. Introduction
Vigor2830 series is an ADSL2+ router. It integrates IP layer QoS, NAT
session/bandwidth management to help users control works well with large bandwidth.
By adopting hardware-based VPN platform and hardware encryption of AES/DES/3DES,
and hardware key hash of SHA-1/MD5, the router increases the performance of VPN
greatly, and offers several protocols (such as IPSec/PPTP/L2TP) with up to 32 VPN
tunnels.
The object-based design used in SPI (Stateful Packet Inspection) firewall allows users to
set firewall policy with ease. CSM (Content Security Management) provides users control
and management in IM (Instant Messenger) and P2P (Peer to Peer) more efficiency than
before. By the way, DoS/DDoS prevention and URL/Web content filter strengthen the
security outside and control inside.
In addition, Vigor2830 series supports USB interface for connecting USB printer to share
printer or USB storage device for sharing files. Vigor2830 series provides two-level
management to simplify the configuration of network connection. The user operation
allows user accessing into WEB interface via simple configuration. However, if users
want to have advanced configurations, they can access into WEB interface through
administration operation.
1
Vigor2830 Series Quick Start Guide
1.1 Panel Explanation
1.1.1 For Vigor2830
LED
Status
Explanation
ACT (Activity)
CSM
Blinking
Off
On
Blinking
On
WCF
On
DSL
On
Blinking
WAN2
On
Blinking
On
Blinking
On
On
The router is powered on and running normally.
The router is powered off.
USB device is connected and ready for use.
The data is transmitting.
The profile(s) of CSM (Content Security Management)
for IM/P2P, URL/Web Content Filter application can be
enabled from Firewall >>General Setup. (Such profile
must be established under CSM menu).
The Web Content Filter is active. (It is enabled from
Firewall >> General Setup).
The router is ready to access Internet through DSL link.
Slowly: The DSL connection is ready.
Quickly: The connection is training.
The WAN2 connection is ready.
It will blink while transmitting data.
The DoS/DDoS function is active.
It will blink while detecting an attack.
The VPN tunnel is active.
The QoS function is active.
USB
DoS
VPN
QoS
LED on Connector
GigaLAN
1/2/3/4
Left LED
(Green)
Right LED
(Green)
WAN2
(Giga)
Left LED
(Green)
Right LED
(Green)
Vigor2830 Series Quick Start Guide
On
Off
Blinking
On
Off
On
Off
Blinking
On
Off
The port is connected.
The port is disconnected.
The data is transmitting.
The port is connected with 1000Mbps.
The port is disconnected with 10/100Mbps when left
LED is on.
The port is connected.
The port is disconnected.
The data is transmitting.
The port is connected with 1000Mbps.
The port is disconnected with 10/100Mbps when left
LED is on.
2
Interface
Description
Factory Reset
GigaLAN (1-4)
DSL
WAN2(Giga)
USB
PWR
Restore the default settings. Usage: Turn on the router (ACT LED is
blinking). Press the hole and keep for more than 5 seconds. When you
see the ACT LED begins to blink rapidly than usual, release the button.
Then the router will restart with the factory default configuration.
Connecters for local network devices.
Connecter for accessing the Internet through ADSL2/2+.
Connecter for remote network devices.
Connecter for a USB device (for 3G USB Modem or printer).
Connecter for a power adapter.
ON/OFF
Power Switch.
3
Vigor2830 Series Quick Start Guide
1.1.2 For Vigor2830n
LED
Status
Explanation
ACT (Activity)
Blinking
Off
On
Blinking
On
The router is powered on and running normally.
The router is powered off.
USB device is connected and ready for use.
The data is transmitting.
The profile(s) of CSM (Content Security Management)
for IM/P2P, URL/Web Content Filter application can be
enabled from Firewall >>General Setup. (Such profile
must be established under CSM menu).
Wireless access point is ready.
It will blink slowly while wireless traffic goes through.
ACT and WLAN LEDs blink quickly and
simultaneously when WPS is working, and will return to
normal condition after two minutes. (You need to setup
WPS within 2 minutes.)
The router is ready to access Internet through DSL link.
Slowly: The DSL connection is ready.
Quickly: The connection is training.
The WAN2 connection is ready.
It will blink while transmitting data.
The DoS/DDoS function is active.
It will blink while detecting an attack.
The VPN tunnel is active.
The QoS function is active.
USB
CSM
WLAN
On
Blinking
DSL
On
Blinking
WAN2
On
Blinking
On
Blinking
On
On
DoS
VPN
QoS
LED on Connector
GigaLAN
1/2/3/4
Left LED
(Green)
Right LED
(Green)
WAN2
(Giga)
Left LED
(Green)
Right LED
(Green)
Vigor2830 Series Quick Start Guide
On
Off
Blinking
On
Off
On
Off
Blinking
On
Off
The port is connected.
The port is disconnected.
The data is transmitting.
The port is connected with 1000Mbps.
The port is disconnected with 10/100Mbps when left
LED is on.
The port is connected.
The port is disconnected.
The data is transmitting.
The port is connected with 1000Mbps.
The port is disconnected with 10/100Mbps when left
LED is on.
4
Interface
Description
Wireless LAN
ON/OFF/WPS
GigaLAN (1-4)
DSL
WAN2(Giga)
USB
PWR
Press "Wireless LAN ON/OFF/WPS" button once to wait for client
device making network connection through WPS.
Press "Wireless LAN ON/OFF/WPS" button twice to enable (WLAN
LED on) or disable (WLAN LED off) wireless connection.
Restore the default settings. Usage: Turn on the router (ACT LED is
blinking). Press the hole and keep for more than 5 seconds. When you
see the ACT LED begins to blink rapidly than usual, release the button.
Then the router will restart with the factory default configuration.
Connecters for local network devices.
Connecter for accessing the Internet through ADSL2/2+.
Connecter for remote network devices.
Connecter for a USB device (for 3G USB Modem or printer).
Connecter for a power adapter.
ON/OFF
Power Switch.
Factory Reset
5
Vigor2830 Series Quick Start Guide
1.1.3 For Vigor2830Vn
LED
Status
Explanation
ACT (Activity)
Blinking
Off
On
Blinking
On
The router is powered on and running normally.
The router is powered off.
USB device is connected and ready for use.
The data is transmitting.
The profile(s) of CSM (Content Security Management)
for IM/P2P, URL/Web Content Filter application can be
enabled from Firewall >>General Setup. (Such profile
must be established under CSM menu).
Wireless access point is ready.
It will blink slowly while wireless traffic goes through.
ACT and WLAN LEDs blink quickly and
simultaneously when WPS is working, and will return to
normal condition after two minutes. (You need to setup
WPS within 2 minutes.)
The router is ready to access Internet through DSL link.
Slowly: The DSL connection is ready.
Quickly: The connection is training.
The WAN2 connection is ready.
It will blink while transmitting data.
A PSTN phone call comes (in and out). However, when
the phone call is disconnected, the LED will be off.
There is no PSTN phone call.
The phone connected to this port is off-hook.
The phone connected to this port is on-hook.
A phone call comes.
USB
CSM
WLAN
On
Blinking
DSL
On
Blinking
WAN2
On
Blinking
On
Line
Off
On
Off
Blinking
Phone 1/2
LED on Connector
GigaLAN
1/2/3/4
Left LED
(Green)
Right LED
(Green)
WAN2
(Giga)
Left LED
(Green)
Right LED
(Green)
Vigor2830 Series Quick Start Guide
On
Off
Blinking
On
Off
On
Off
Blinking
On
Off
The port is connected.
The port is disconnected.
The data is transmitting.
The port is connected with 1000Mbps.
The port is connected with 10/100Mbps when left LED
is on.
The port is connected.
The port is disconnected.
The data is transmitting.
The port is connected with 1000Mbps.
The port is connected with 10/100Mbps when left LED
is on.
6
Interface
Description
Wireless LAN
ON/OFF/WPS
Phone 1/2
Line
GigaLAN (1-4)
DSL
WAN2(Giga)
USB
PWR
Press "Wireless LAN ON/OFF/WPS" button once to wait for client
device making network connection through WPS.
Press "Wireless LAN ON/OFF/WPS" button twice to enable (WLAN
LED on) or disable (WLAN LED off) wireless connection.
Restore the default settings. Usage: Turn on the router (ACT LED is
blinking). Press the hole and keep for more than 5 seconds. When you
see the ACT LED begins to blink rapidly than usual, release the button.
Then the router will restart with the factory default configuration.
Connecter for analog phone(s).
Connector for PSTN life line.
Connecters for local network devices.
Connecter for accessing the Internet through ADSL2/2+.
Connecter for remote network devices.
Connecter for a USB device (for 3G USB Modem or printer).
Connecter for a power adapter.
ON/OFF
Power Switch.
Factory Reset
7
Vigor2830 Series Quick Start Guide
1.1.4 For Vigor2830VS
LED
Status
Explanation
ACT (Activity)
CSM
Blinking
Off
On
Blinking
On
WCF
On
DSL
On
Blinking
WAN 2
On
Blinking
On
Off
Blinking
On
The router is powered on and running normally.
The router is powered off.
A USB device is connected and active.
The data is transmitting.
The profile of CSM (Content Security Management)
for IM/P2P application is enabled from Firewall >>
General Setup. (Such profile is established under
CSM menu).
The Web Content Filter is active. (It is enabled from
Firewall >> Web Content Filter and the web content
filter profile is established under CSM menu.)
The router is ready to access Internet through DSL link.
Slowly: The modem is ready.
Quickly: The connection is training.
The WAN1 or WAN2 connection is ready.
It will blink while transmitting data.
The phone connected to this port is off-hook.
The phone connected to this port is on-hook.
A phone call comes.
A PSTN phone call comes (in and out). However, when
the phone call is disconnected, the LED will be off
about six seconds later.
There is no PSTN phone call.
The phone connected to this port is off-hook.
The phone connected to this port is on-hook.
A phone call comes.
The QoS function is active.
USB
Phone
Line
Off
On
Off
Blinking
On
Phone
QoS
LED on Connector
On
Phone S0
Left LED
(Orange)
Blinking
On
Right LED
(Green)
ISDN/Pho
ne S0
Blinking
On
Left LED
(Orange)
Blinking
Off
Right LED
Vigor2830 Series Quick Start Guide
On
ISDN NT (ISDN S0 intern) mode is active and an
ISDN phone adapter is connected.
ISDN NT (ISDN S0 intern) mode is active and an
ISDN phone adapter is not connected.
A phone has been connected. If not, green LED will be
off.
An ISDN phone is off-hook or a phone call comes.
ISDN NT (ISDN S0 intern) mode is active configured
from VoIP>>Phone Settings and an ISDN phone
adapter is connected.
ISDN NT (ISDN S0 intern) mode configured from
VoIP>>Phone Settings is active and an ISDN phone
adapter is not connected.
It means ISDN TE mode is active which is configured
from VoIP>>Phone Settings.
A phone adapter with phone set has been connected
8
(Green)
Blinking
LAN
1(Giga)
Left LED
(Green)
Right LED
(Green)
LAN
2/3/4
Left LED
(Green)
Right LED
(Green)
WAN2
(Giga)
Left LED
(Green)
Right LED
(Green)
On
Off
Blinking
On
Off
On
Off
Blinking
On
Off
On
Off
Blinking
On
Off
(ISDN S0 intern mode) or ISDN line has been
connected (ISDN S0 extern mode). It will be off if
there is nothing connected.
In ISDN NT (ISDN S0 intern) mode, it means an ISDN
phone is off-hook or a phone call comes.
In ISDN TE mode, it means data, fax or voice (phone
call) is transmitting.
The port is connected.
The port is disconnected.
The data is transmitting.
The port is connected with 1000Mbps.
The port is connected with 10/100Mbps.
The port is connected.
The port is disconnected.
The data is transmitting.
The port is connected with 100Mbps.
The port is connected with 10Mbps.
The port is connected.
The port is disconnected.
The data is transmitting.
The port is connected with 1000Mbps.
The port is connected with 10/100Mbps when left LED
is on.
Interface
Description
Factory Reset
Phone
Line
LAN (1-4)
DSL
WAN2(Giga)
USB
PWR
Restore the default settings.
Usage: Turn on the router (ACT LED is blinking). Press the hole and
keep for more than 5 seconds. When you see the ACT LED begins to
blink rapidly than usual, release the button. Then the router will restart
with the factory default configuration.
Connecter for ISDN phone(s) only via ISDN phone adapter. Do not
connect any other device to such port or connect ISDN line, otherwise
the router might be damaged.
Connecter for ISDN line or ISDN phone adapter in particular condition.
Refer to section 2.2 for more details.
Connecter for PSTN phone.
Connector for PSTN life line.
Connecters for local networked devices.
Connecter for accessing the Internet through ADSL2/2+.
Connecter for remote networked devices.
Connecter for a USB device (for 3G USB Modem or printer).
Connecter for a power adapter.
ON/OFF
Power Switch.
Phone S0
ISDN/Phone S0
9
Vigor2830 Series Quick Start Guide
1.1.6 For Vigor2830VSn
LED
Status
Explanation
ACT (Activity)
Blinking
Off
On
Blinking
On
The router is powered on and running normally.
The router is powered off.
A USB device is connected and active.
The data is transmitting.
The profile of CSM (Content Security Management)
for IM/P2P application is enabled from Firewall >>
General Setup. (Such profile is established under
CSM menu).
Wireless access point is ready.
It will blink while wireless traffic goes through.
If ACT and WLAN LEDs blink simultaneously when
WPS is working, and it will return to normal condition
after two minutes. (You need to setup WPS within 2
minutes.)
The router is ready to access Internet through DSL
link.
Slowly: The modem is ready.
Quickly: The connection is training.
The WAN1 or WAN2 connection is ready.
It will blink while transmitting data.
A PSTN phone call comes (in and out). However,
when the phone call is disconnected, the LED will be
off about six seconds later.
There is no PSTN phone call.
The phone connected to this port is off-hook.
The phone connected to this port is on-hook.
A phone call comes.
The QoS function is active.
USB
CSM
WLAN
On
Blinking
DSL
On
Blinking
WAN 2
On
Blinking
On
Line
Off
On
Off
Blinking
On
Phone
QoS
LED on Connector
On
Phone S0
Left LED
(Orange)
Blinking
On
Right LED
(Green)
ISDN/Pho
ne S0
Blinking
On
Left LED
(Orange)
Blinking
Off
Right LED
(Green)
Vigor2830 Series Quick Start Guide
On
ISDN NT (ISDN S0 intern) mode is active and an
ISDN phone adapter is connected.
ISDN NT (ISDN S0 intern) mode is active and an
ISDN phone adapter is not connected.
A phone has been connected. If not, green LED will be
off.
An ISDN phone is off-hook or a phone call comes.
ISDN NT (ISDN S0 intern) mode is active configured
from VoIP>>Phone Settings and an ISDN phone
adapter is connected.
ISDN NT (ISDN S0 intern) mode configured from
VoIP>>Phone Settings is active and an ISDN phone
adapter is not connected.
It means ISDN TE mode is active which is configured
from VoIP>>Phone Settings.
A phone adapter with phone set has been connected
(ISDN S0 intern mode) or ISDN line has been
10
Blinking
LAN
1(Giga)
Left LED
(Green)
Right LED
(Green)
LAN
2/3/4
Left LED
(Green)
Right LED
(Green)
WAN2
(Giga)
Left LED
(Green)
Right LED
(Green)
Interface
Wireless LAN
ON/OFF/WPS
On
Off
Blinking
On
Off
On
Off
Blinking
On
Off
On
Off
Blinking
On
Off
connected (ISDN S0 extern mode). It will be off if
there is nothing connected.
In ISDN NT (ISDN S0 intern) mode, it means an
ISDN phone is off-hook or a phone call comes.
In ISDN TE mode, it means data, fax or voice (phone
call) is transmitting.
The port is connected.
The port is disconnected.
The data is transmitting.
The port is connected with 1000Mbps.
The port is connected with 10/100Mbps.
The port is connected.
The port is disconnected.
The data is transmitting.
The port is connected with 100Mbps.
The port is connected with 10Mbps.
The port is connected.
The port is disconnected.
The data is transmitting.
The port is connected with 1000Mbps.
The port is connected with 10/100Mbps when left
LED is on.
Description
Phone
Line
LAN (1-4)
DSL
WAN 2
USB
PWR
Press "Wireless LAN ON/OFF/WPS" button for 2 seconds to wait for
client device making network connection through WPS.
Press "Wireless LAN ON/OFF/WPS" button once to enable (WLAN
LED on) or disable (WLAN LED off) wireless connection.
Restore the default settings.
Usage: Turn on the router (ACT LED is blinking). Press the hole and
keep for more than 5 seconds. When you see the ACT LED begins to
blink rapidly than usual, release the button. Then the router will restart
with the factory default configuration.
Connecter for ISDN phone(s) only via ISDN phone adapter. Do not
connect any other device to such port or connect ISDN line, otherwise
the router might be damaged.
Connecter for ISDN line or ISDN phone adapter in particular condition.
Refer to section 2.2 for more details.
Connecter for PSTN phone.
Connector for PSTN life line.
Connecters for local networked devices.
Connecter for accessing the Internet through ADSL2/2+.
Connecter for remote networked devices.
Connecter for a USB device (for 3G USB Modem or printer).
Connecter for a power adapter.
ON/OFF
Power Switch.
Factory Reset
Phone S0
ISDN/Phone S0
11
Vigor2830 Series Quick Start Guide
1.2 Package Content
nQuick Start Guide
oCD
p RJ-45 Cable (Ethernet)
q Antenna (n models)
r The type of the power adapter depends on the country that the router will be
installed:
UK-type Power Adapter
EU-type Power Adapter
USA/Taiwan-type Power Adapter
AU/NZ-type Power Adapter
* The maximum power consumption is 20 Watt.
Vigor2830 Series Quick Start Guide
12
2. Installing Your Router
This section will guide you to install the router through hardware connection and
configure the router’s settings through web browser.
2.1 Hardware Installation
Before starting to configure the router, you have to connect your devices correctly.
1.
Connect the ADSL interface to the external ADSL splitter with an ADSL line cable
for all models. For Vigor2830Vn, also connect Line interface to external ADSL
splitter.
2.
Connect one end of an Ethernet cable (RJ-45) to one of the LAN ports of the router
and the other end of the cable (RJ-45) into the Ethernet port on your computer.
3.
Connect the telephone set with phone lines (for using VoIP function). For the model
without phone ports, skip this step.
4.
Connect one end of the power adapter to the router’s power port on the rear panel,
and the other side into a wall outlet.
5.
Power on the device by pressing down the power switch on the rear panel.
6.
The system starts to initiate. After completing the system test, the ACT LED will
light up and start blinking.
(For the hardware connection, we take “Vn” model as an example.)
13
Vigor2830 Series Quick Start Guide
.
Vigor2830 Series Quick Start Guide
14
2.2 Printer Installation
You can install a printer onto the router for sharing printing. All the PCs connected this
router can print documents via the router. The example provided here is made based on
Windows XP/2000. For Windows 98/SE/Vista, please visit www.draytek.com.
Before using it, please follow the steps below to configure settings for connected
computers (or wireless clients).
1.
Connect the printer with the router through USB port.
2.
Open Start->Settings-> Printers and Faxes.
15
Vigor2830 Series Quick Start Guide
3.
Open File->Add a New Computer. A welcome dialog will appear. Please click
Next.
4.
Click Local printer attached to this computer and click Next.
5.
In this dialog, choose Create a new port Type of port and use the drop down list to
select Standard TCP/IP Port. Click Next.
Vigor2830 Series Quick Start Guide
16
6.
In the following dialog, type 192.168.1.1 (router’s LAN IP) in the field of Printer
Name or IP Address and type IP_192.168.1.1 as the port name. Then, click Next.
7.
Click Standard and choose Generic Network Card.
8.
Then, in the following dialog, click Finish.
17
Vigor2830 Series Quick Start Guide
9.
Now, your system will ask you to choose right name of the printer that you installed
onto the router. Such step can make correct driver loaded onto your PC. When you
finish the selection, click Next.
10. For the final stage, you need to go back to Control Panel-> Printers and edit the
property of the new printer you have added.
11. Select "LPR" on Protocol, type p1 (number 1) as Queue Name. Then click OK.
Next please refer to the red rectangle for choosing the correct protocol and LPR
name.
Vigor2830 Series Quick Start Guide
18
The printer can be used for printing now. Most of the printers with different
manufacturers are compatible with vigor router.
Note 1: Some printers with the fax/scanning or other additional functions are not
supported. If you do not know whether your printer is supported or not, please
visit www.draytek.com to find out the printer list. Open Support >FAQ; find out
the link of Printer Server and click it; then click the What types of printers are
compatible with Vigor router? link.
Note 2: Vigor router supports printing request from computers via LAN ports but
not WAN port.
19
Vigor2830 Series Quick Start Guide
This page is left blank.
Vigor2830 Series Quick Start Guide
20
3. Configuring Web Pages
To access Internet, please finish basic configuration after completing the hardware
installation.
3.1 Accessing Web Page
1.
Make sure your PC connects to the router correctly.
Notice: You may either simply set up your computer to get IP dynamically
from the router or set up the IP address of the computer to be the same
subnet as the default IP address of Vigor router 192.168.1.1. For the
detailed information, please refer to the later section - Trouble Shooting of
the guide.
2.
Open a web browser on your PC and type http://192.168.1.1. The following window
will be open to ask for username and password.
3.
For user mode, do not type any word on the window and click Login for the simple
web pages for configuration. Yet, for admin mode, please type “admin/admin” on
Username/Password and click Login for full configuration.
Notice: If you fail to access to the web configuration, please go to “Trouble
Shooting” for detecting and solving your problem.
4.
The web page can be logged out according to the chosen condition. The default
setting is Auto Logout, which means the web configuration system will logout after
five minutes without any operation. Change the setting for your necessity.
5.
Now, the Main Screen will pop up.
21
Vigor2830 Series Quick Start Guide
3.2 Basic Configuration
The Quick Start Wizard is designed for you to easily set up your router for Internet
access. You can directly access the Quick Start Wizard via Web Configurator.
1.
Open a web browser on your PC and type http://192.168.1.1. The system will ask
you to type username/password. The displayed web pages will change according to
the username and password typed. Here we take simple web pages for example. So,
do not type any word on the window and click Login.
Notice: For advanced configuration (admin mode), please refer to User’s
Guide for more detailed information.
2.
Now, the Main Screen for user operation will appear. Click Quick Start Wizard.
Note: The home page will change slightly in accordance with the router model you
have.
3.
Enter the login password on the field of New Password and retype it on the field of
Confirm Password. Then click Next to continue.
Vigor2830 Series Quick Start Guide
22
4.
On the next page as shown below, please select the WAN interface that you use. If
DSL interface is used, please choose WAN1; if Ethernet interface is used, please
choose WAN2; if 3G USB modem is used, please choose WAN3. Then click Next
for next step.
WAN1, WAN2 and WAN3 will bring up different configuration page. Refer to the
following for detailed information.
For WAN1
Choose WAN1 and click Next to display the following page. Please select the
appropriate Internet access type according to the information from your ISP. For
example, you should select PPPoE mode if the ISP provides you PPPoE interface.
Then click Next for next step.
23
Vigor2830 Series Quick Start Guide
PPPoE/PPPoA: if you click PPPoE or PPPoA as the protocol, please manually enter
the Username/Password provided by your ISP. Then click Next.
Vigor2830 Series Quick Start Guide
24
1483 Bridged IP /1483 Routed IP: if you choose 1483 Bridged IP / 1483 Routed IP
as the protocol, you will get the following page. Please type in the IP address
information originally provided by your ISP. Then click Next for next step.
Now you can see the following screen. It indicates that the setup is complete.
Different types of connection modes will have different summary. Click Finish and
then restart the router. Afterward, you will enjoy surfing on the Internet.
25
Vigor2830 Series Quick Start Guide
For WAN2
If you choose WAN2, you have to choose physical mode and specify physical type.
Then, click Next.
On the next page as shown below, please select the appropriate Internet access type
according to the information from your ISP. For example, you should select PPPoE
mode if the ISP provides you PPPoE interface. Then click Next for next step.
Vigor2830 Series Quick Start Guide
26
PPPoE: if you click PPPoE as the protocol, please manually enter the
Username/Password provided by your ISP. Then click Next.
PPTP/L2TP: if you click PPTP/L2TP, you will get the following page. Please type
in all the information originally provided by your ISP. Then click Next for next step.
27
Vigor2830 Series Quick Start Guide
Static IP: if you click Static IP, you will get the following page. Please type in the IP
address information originally provided by your ISP. Then click Next for next step.
DHCP: if you click DHCP, you will get the following page. Simply click Next to
continue.
Vigor2830 Series Quick Start Guide
28
Now you can see the following screen. It indicates that the setup is complete.
Different types of connection modes will have different summary. Click Finish and
then restart the router. Afterward, you will enjoy surfing on the Internet.
29
Vigor2830 Series Quick Start Guide
3.3 Wireless Configuration
For the user of Vigor2830, please skip this section.
For operating Vigor2830n well, it is necessary for you to set the wireless LAN settings
for using wireless function. Please read the following section carefully for configuring the
settings for this router.
(The default value of Frequency Domain was set by factory depends on the reselling
region.)
3.3.1 Basic Wireless LAN Concept
In an Infrastructure Mode of wireless network, Vigor wireless router plays a role as an
Access Point (AP) connecting to lots of wireless clients or Stations (STA). All the STAs
(clients) will share the same Internet connection with other wired hosts via Vigor wireless
router.
Vigor2830 Series Quick Start Guide
30
3.3.2 General Setup
1.
On the Wireless LAN group, select General Setup. The following page will be
shown.
2.
Check Enable Wireless LAN to enable the wireless function.
3.
At present, the router can connect to IEEE802.11b, IEEE802.11g and IEEE802.11n
stations simultaneously. Simply choose Mixed (11b+11g+11n) mode.
4.
Type in the name of the SSID. The default name for SSID is DrayTek. We suggest
you change it to a particular name for your necessity.
SSID (service set
identifier)
It is used to name the wireless LAN for this router, and it must
have the same content in client PC/notebook wireless card(s).
SSID can be any text numbers or various special characters.
Channel
It is a wireless channel for the router. The default channel is 6.
You can change it to an appropriate one if the selected channel
is under serious interference.
31
Vigor2830 Series Quick Start Guide
3.3.3 Security Settings
1.
On the Wireless LAN group, select Security.
2.
The default security mode is Mixed (WPA+WPA2)/PSK. Default Pre-Shared Key
(PSK) is provided and stated on the label pasted on the bottom of the router. For the
wireless client who wants to access into Internet through such router, please input
the default PSK value for connection.
Disable
Turn off the encryption mechanism. For the security of
your router, please select any one of the encryption
mode here.
WEP
Accepts only WEP clients and the encryption key
should be entered in WEP Key.
WPA/PSK
Accepts only WPA clients and the encryption key
should be entered in PSK.
WPA2/PSK
Accepts only WPA2 clients and the encryption key
should be entered in PSK.
Mixed (WPA+WPA2)/
PSK
Accepts WPA and WPA2 clients, and the encryption
key should be entered in PSK.
Vigor2830 Series Quick Start Guide
32
3.
For WPA encryption, type in 8~63 ASCII characters or 64 Hexadecimal digits
leading by 0x, for example "0123456789ABCD...." or "0x321253abcde....." on the
field of Pre-Shared Key (PSK). WPA encrypts each frame transmitted from the
radio using the Pre-Shared Key (PSK) which entered from this panel.
4.
As to WEP encryption, select 64-bit or 128-bit as the encryption mode. For 64bits
WEP key, type in 5 ASCII characters or 10 hexadecimal digitals leading by 0x, for
example, ABCDE or 0x4142434445. And for 128bits WEP key, type in 13 ASCII
characters or 26 hexadecimal digits leading by 0x, for example, ABCDEFGHIJKLM
or 0x4142434445464748494A4B4C4D. Only one WEP key can be selected and
allows user to type in the characters.
5.
Click OK to save settings.
Be aware that for the communication, all wireless devices must support the same
encryption bit length and share the same key. If WEP mode is selected, only one of four
preset keys can be selected at one time.
33
Vigor2830 Series Quick Start Guide
This page is left blank.
Vigor2830 Series Quick Start Guide
34
4. Trouble Shooting
This section will guide you to solve abnormal situations if you cannot access into the
Internet after installing the router and finishing the web configuration. Please follow
sections below to check your basic installation status stage by stage.
¾
Checking if the hardware status is OK or not.
¾
Checking if the network connection settings on your computer are OK or not.
¾
Pinging the router from your computer.
¾
Checking if the ISP settings are OK or not.
¾
Backing to factory default setting if necessary.
If all above stages are done and the router still cannot run normally, it is the time for you
to contact your dealer for advanced help.
4.1 Checking If the Hardware Status Is OK or Not
Follow the steps below to verify the hardware status.
1.
Check the power line and LAN cable connections. Refer to “2.1 Hardware
Installation” for details.
2.
Turn on the router. Make sure the ACT LED blink once per second and the
correspondent LAN LED is bright.
3.
If not, it means that there is something wrong with the hardware status. Simply back
to “2.1 Hardware Installation” to execute the hardware installation again. And
then, try again.
35
Vigor2830 Series Quick Start Guide
4.2 Checking If the Network Connection Settings on Your
Computer Is OK or Not
Sometimes the link failure occurs due to the wrong network connection settings. After
trying the above section, if the link is stilled failed, please do the steps listed below to
make sure the network connection settings is OK.
For Windows
The example is based on Windows XP. As to the examples for other
operation systems, please refer to the similar steps or find support notes in
www.draytek.com.
1.
Go to Control Panel and then double-click on Network Connections.
2.
Right-click on Local Area Connection and click on Properties.
3.
Select Internet Protocol (TCP/IP) and then click Properties.
Vigor2830 Series Quick Start Guide
36
4.
Select Obtain an IP address automatically and Obtain DNS server address
automatically.
For MacOs
1.
Double click on the current used MacOs on the desktop.
2.
Open the Application folder and get into Network.
3.
On the Network screen, select Using DHCP from the drop down list of Configure
IPv4.
37
Vigor2830 Series Quick Start Guide
4.3 Pinging the Router from Your Computer
The default gateway IP address of the router is 192.168.1.1. For some reason, you might
need to use “ping” command to check the link status of the router. The most important
thing is that the computer will receive a reply from 192.168.1.1. If not, please check
the IP address of your computer. We suggest you setting the network connection as get IP
automatically. (Please refer to the section 4.2)
Please follow the steps below to ping the router correctly.
For Windows
1.
2.
Open the Command Prompt window (from Start menu> Run).
Type command (for Windows 95/98/ME) or cmd (for Windows NT/
2000/XP/Vista). The DOS command dialog will appear.
3.
Type ping 192.168.1.1 and press [Enter]. If the link is OK, the line of “Reply from
192.168.1.1:bytes=32 time<1ms TTL=255” will appear.
4.
If the line does not appear, please check the IP address setting of your computer.
For MacOs (Terminal)
1.
Double click on the current used MacOs on the desktop.
2.
Open the Application folder and get into Utilities.
3.
Double click Terminal. The Terminal window will appear.
4.
Type ping 192.168.1.1 and press [Enter]. If the link is OK, the line of “64 bytes
from 192.168.1.1: icmp_seq=0 ttl=255 time=xxxx ms” will appear.
Vigor2830 Series Quick Start Guide
38
4.4 Checking If the ISP Settings are OK or Not
Open WAN >> Internet Access page and then check whether the ISP settings are set
correctly. Click Details Page of WAN1/WAN2/WAN3 to review the settings that you
configured previously.
4.5 Backing to Factory Default Setting If Necessary
Sometimes, a wrong connection can be improved by returning to the default settings. Try
to reset the router by software or hardware. only.
Warning: After pressing factory default setting, you will loose all settings
you did before. Make sure you have recorded all useful settings before you
pressing. The password of factory default is null.
Software Reset
You can reset the router to factory default via Web page. Such function is available in
Admin Mode only.
Go to System Maintenance and choose Reboot System on the web page. The following
screen will appear. Choose Using factory default configuration and click OK. After few
seconds, the router will return all the settings to the factory settings.
39
Vigor2830 Series Quick Start Guide
Hardware Reset
While the router is running (ACT LED blinking), press the RST button and hold for more
than 5 seconds. When you see the ACT LED blinks rapidly, please release the button.
Then, the router will restart with the default configuration.
After restore the factory default setting, you can configure the settings for the router again
to fit your personal request.
4.6 Contacting Your Dealer
If the router still cannot work correctly after trying many efforts, please contact your
dealer for further help right away. For any questions, please feel free to send e-mail to
support@draytek.com.
Vigor2830 Series Quick Start Guide
40