2008 GC-STWC Operators Manual - 03229

THIS MANUAL CONTAINS THE OPERATING
INSTRUCTIONS AND SAFETY INFORMATION FOR YOUR SCAG ACCESSORY. READING THIS MANUAL WILL PROVIDE YOU
WITH MAINTENANCE AND ADJUSTMENT
PROCEDURES TO KEEP YOUR ACCESSORY
PERFORMING TO MAXIMUM EFFICIENCY.
THE SPECIFIC MODELS THAT THIS BOOK
COVERS ARE CONTAINED ON THE INSIDE
COVER. BEFORE OPERATING YOUR MACHINE, PLEASE READ ALL THE INFORMATION ENCLOSED.
OPERATOR’S MANUAL
MODEL GC-STWC-61
PART NUMBER 03229
WARNING
FAILURE TO FOLLOW SAFE OPERATING PRACTICES
MAY RESULT IN SERIOUS INJURY.
* Keep all safety shields in place.
* Before performing any maintenance or service, stop the machine and
remove the spark plug wire.
* If a mechanism becomes clogged, stop the engine before cleaning.
* Keep hands, feet and clothing away from power-driven parts.
* Read this manual completely as well as the Operator's Manual that came
with your mower.
* Keep others off the Mower (only one person at a time).
REMEMBER - YOUR MOWER IS ONLY AS SAFE AS THE OPERATOR!
Hazard control and accident prevention are dependent upon the awareness,
concern, prudence, and proper training of the personnel involved in the
operation, transport, maintenance, and storage of the equipment.
This manual covers the operating instructions
and illustrated parts list for:
GC-STWC-61 with a serial number of E0100001 to E0199999
1.1 INTRODUCTION
A replacement manual is available from your
authorized Scag Service Dealer or by contacting:
Scag Power Equipment, Service Department at P.O.
Box 152, Mayville, WI 53050. You may also contact
us through our website at www.scag.com The
manual for this grass catcher can be downloaded by
using the model and serial number or use the contact
form to make your request. Please indicate the
complete model and serial number of your Scag
product when requesting replacement manuals.
This manual has been prepared to provide the
information you need to correctly assemble, operate,
and maintain this grass catcher. Read it carefully and
keep it for future reference.
THE REPLACEMENT OF ANY PART ON THIS
PRODUCT BY OTHER THAN THE
MANUFACTURER'S AUTHORIZED
REPLACEMENT PART MAY ADVERSELY
AFFECT THE PERFORMANCE, DURABILITY
OR SAFETY OF THIS PRODUCT.
WARNING
USE OF OTHER THAN ORIGINAL SCAG
REPLACEMENT PARTS WILL VOID THE
WARRANTY.
DO NOT OPERATE WITHOUT DISCHARGE CHUTE, MULCHING
KIT, OR ENTIRE GRASS CATCHER INSTALLED
If additional information or service is needed that is
not outlined in this manual, please contact your Scag
Power Equipment dealer. Scag dealers are trained in
the latest service methods and carry a full line of Scag
replacement parts.
2. Before removing the grass bags, disengage the
mower, stop the engine and wait for all
movement to stop.
When ordering parts, always provide the complete
model number of your catcher.
3. ALWAYS turn the engine OFF, remove the key
and wait for all movement to stop before
servicing or cleaning the mower or the grass
catcher.
All information provided in this manual is based upon
information available at the time of printing. Scag
Power Equipment reserves the right to make changes
at any time without notice or obligation.
DANGER
ROTATING BLOWER
BLADES
1.2 DIRECTION REFERENCE
STOP ENGINE BEFORE
ENTERING CHUTE
The "Right" and "Left", "Front" and "Rear" of the
machine are referenced from the normal operating
position.
CONTACT CAN INJURE
2.1 SAFETY AND OPERATING
INSTRUCTIONS
4. Do not modify or alter any component of the
grass catcher attachment or mower.
-NOTETo avoid personal injury, it is imperative that all
safety instructions be observed.
5. Do not allow any passengers to ride on the grass
catcher attachment or on the mower.
1. Read this operator's manual and the
operator's manual that is supplied with the
machine this attachment is used on.
1
4. Install the grass catcher pulley onto the spindle
assembly. Apply loctite to both pulley setscrews
and tighten. See Figure 3-1.
3.1 ASSEMBLY INSTRUCTIONS FOR 61"
CUTTER DECK
-NOTEUse the illustrated parts list as a part number
reference when following the assembly
instructions.
5. Install the blower mounting bracket to the deck
using carriage bolts (p/n 04003-11), lockwashers,
and nuts. Do not fully tighten the hardware at
this time. See Figure 3-2, Page 3.
1. Remove all packaging materials. Lay out the
mounting hardware and the catcher assembly
parts for easy access. Prepare the work area
making sure that it is a clean, safe environment.
6. Install the blower assembly to the mounting
bracket and secure with the mounting pin.
See Figure 3-3, Page 3.
7. Align the blower assembly with the discharge
opening of the cutter deck. Tighten the hardware
for the mounting bracket. Then tighten the
hardware for the catch plate. See Figure 3-3,
Page 3.
WARNING
DO NOT OPERATE WITHOUT DISCHARGE CHUTE, MULCHING
KIT, OR ENTIRE GRASS CATCHER INSTALLED
8. Install the large hair pin through the rear hole in
the discharge chute mounting bracket. See
Figure 3-3, Page 3.
2. Remove the discharge chute from the cutter
deck. See Figure 3-1.
-NOTEDo not discard the discharge chute or
mounting hardware. The discharge chute
MUST be reinstalled any time the grass
catcher has been removed from the machine.
9. Install the belt to the spindle pulley. When
replacing the belt, see figure below.
BACK SIDE
IDLER PULLEY
BLOWER
PULLEY
3. Remove the right side belt cover to gain access to
the spindle assembly. Remove the front u-nut
from the cutter deck bracket. See Figure 3-1.
-NOTERetain the original belt cover. This cover
MUST be reinstalled any time the
complete catcher system is removed.
REMOVE DISCHARGE
CHUTE AND
HARDWARE
INSTALL PULLEY
ON RH SPINDLE SHAFT ON TOP OF EXISTING
SPINDLE DRIVE
PULLEY
FRONT SIDE
IDLER PULLEY
REMOVE EXISTING
RT. SIDE BELT
COVER
REMOVE U-NUT
RIGHT SIDE OF
CUTTER DECK SHOWN
(Note: Some parts not shown for viewing purposes.)
Figure 1- GC-STC install art
FIGURE 3-1
2
SPINDLE
PULLEY
FLATWASHER
ELASTIC STOP
NUT
CARRIAGE BOLT
FIGURE 3-2
BLOWER
ASSEMBLY
HAIR
PIN
MOUNTING
BRACKET
TIGHTEN
CATCH PLATE
HARDWARE
MOUNTING PIN
TIGHTEN MOUNTING
BRACKET HARDWARE
RIGHT SIDE OF
CUTTER DECK SHOWN
(Note: Some parts not shown for viewing purposes.)
2005 GC-STC install art 3
FIGURE 3-3
3
13. Attach the hood assembly to the machine by
installing the mounting post into the hopper
mounting brackets. Secure with the ring pins and
tighten the locking bolts. See Figure 3-6.
10. Install the new belt covers and secure. See items
number 1 and number 21 on page 8 of the Blower
Mounting Components section in the Illustrated
Parts List for proper installation.
11. Install the LH & RH hopper mounting brackets to
the outside of the frame on the rear of the machine
and secure using six (6) 3/8-16 x 1" hex head
bolts, and six (6) 3/8-16 elastic stop nuts. See
Figure 3-4. Do Not install mounting hardware in
the rear holes provided in the RH hopper mounting
bracket at this time
LH
Locking
Bolts
Ring Pins
Hopper
Mounting
Bracket
Locking
Bolts
Ring Pins
RH
Hopper
Mounting
Bracket
Rear Frame
FIGURE 3-6
3/8-16
Elastic Stop Nut
04021-09
14. Install the hose from the blower assembly adapter
to the hopper hood and secure using the 6-1/2"
clamps.
Figure 4 A 2008 GC-STT Install Art
3/8-16 x 1”
04001-32
FIGURE 3-4
15. Install the bag assemblies.
12. Remove the upper hex head bolt and serrated
flange nut securing the support bracket to the
frame of the machine. Retain the serrated flange
nut for re-use. Install the muffler guard as shown
and assemble to the frame of the machine by
installing two (2) 3/8-16 x 1-1/4" hex head bolts
through the rear holes in the RH hopper mounting
bracket and secure with two (2) 3/8-16 elastic
stop nuts provided. See Figure 3-5. Install the
front mounting tab of the muffler guard between
the support bracket and the frame of the machine.
Secure with the 3/8-16 x 1-1/2" hex head bolt
supplied with this catcher and the serrated flange
nut removed previously.
16. Using the weight support bar as a guide, identify
the four corresponding mounting holes, and the
existing hardware that will need to be removed in
order to secure the weight support bar to the front
of the machine as shown. See Figure 3-7.
17. Install one (1) 7/16-14 x 1-3/4" hex head bolt into
each of the four mounting holes in the weight
support bar, and through the matching holes in the
caster support weldment. Secure this assembly to
the front of the machine using the
7/16- .5" x 1-1/4" x .083" flatwashers, and the
7/16-14 elastic stop nuts. Torque hardware to
59 ft. lbs. See Figure 3-7.
3/8-16
Elastic Stop Nut
04021-09
Existing
Nut
3/8-16 x 1-1/4
04001-32
Muffler Guard
3/8-16 x 1-1/2
04001-20
Support
Bracket
FIGURE 3-7
18. Operate and test.
FIGURE 3-5
4
4.1 GRASS CATCHER REMOVAL
INSTRUCTIONS
1. Prepare the machine so there is easy and safe
access to the work area. Remove the key and
maintain all safety related work procedures.
Always wear eye and hand protection.
Loosen
Locking
Bolts
2. Remove the bag assemblies from the grass
catcher.
Remove Pins
Loosen
Locking
Bolts
3. Remove the rubber strap holding the adapter to
the blower assembly. See Figure 4-1.
Remove Pins
4. Remove the belt, pin and large hair pin securing
the blower assembly to the cutter deck and
remove the blower assembly. See Figure 4-1.
FIGURE 4-2
ADAPTER
6. With help from an assistant, remove the hood
assembly.
BLOWER
ASSEMBLY
HAIR
PIN
WARNING
PIN
DO NOT OPERATE WITHOUT DISCHARGE CHUTE, MULCHING
KIT, OR ENTIRE GRASS CATCHER INSTALLED
MOUNTING
BRACKET
7. Re-install the side discharge chute to the opening
on the cutter deck. Replace the two outside
mounting bolts on the discharge chute with the
clevis pins (p/n 04064-15) and rue cotter pins
(p/n 04069-03). See Figure 4-3.
RIGHT SIDE OF
CUTTER DECK SHOWN
2005 GC-STC removal art 1
(Note: Some parts not shown for viewing purposes.)
CLEVIS PIN
P/N 04064-15
DISCHARGE
CHUTE
FIGURE 4-1
5. Loosen the locking bolts and remove the two (2)
pins holding the hood assembly to the mounting
posts on the rear of the machine. See Figure 4-2.
CLEVIS PIN
P/N 04064-15
RUE COTTER PIN
P/N 04069-03
GC-STC removal art 3
FIGURE 4-3
5
MAINTENANCE
5.1 MAINTENANCE CHART - RECOMMENDED SERVICE INTERVALS
HOURS
Break-In 8 20 40 100 200 500
(First 10)
Procedure
Comments
X
Check all hardware for tightness
X
Inspect hose and adapter
X
Check belt for proper alignment
X
Inspect fabric bags
X
*Check screen in hopper
X
Inspect hose and adapter
X
Inspect fabric bags
X
Check condition of blower
X
*Apply grease to blower bearings
X
Remove debris from screen
See figure below
Check belt for proper alignment
* Perform these maintenance procedures more frequently under extreme dusty or dirty conditions.
GREASE FITTING
ON BEARING HOUSING
GREASE FITTING
ON BEARING HOUSING
BEHIND PULLEY
6
NOTES
7
GC-STWC BLOWER HOUSING ASSEMBLY
9
48
10
11
12
13
2
1
4
8
9
5
3
11
7
6
10
10
44
14
47
27
14
12
11
15
43
16
42
26
41
39
18
A
W
E
R
FO
E
B
R E
E IN
V HL
O C UA
C M A AN
M
LT 'S
E GR
B TINATO
R
LL RAOPE
TA E D
S PREA
IN O
40
IN
N
R
34
15 14
17
G
27
19
17
25
28
20
41
21
38
3
35
22
27
23
51
24
46
14
GER
DAN
BLOWER
ROTATING
BLADES
BEFORE
STOP
ENGINE
CHUTE
ENTERING
CAN
24
RO
DA
TA
NG
Stop TIN
en G
ER
gine B
DISC UN DO NO be LA
DE
LE
HA SS T OP fore
S
cl
RG GR
E GU AS ERAT eani AN
ng
AR S CA E M
or D
D IS TC OW rem BL
ov OW
INSTHER ER
ing
ER
AL OR
LE
INJURE
D
CONTACT
14
29
ER
NG
DA
ER
OW
BL
RE
ING ES
FO E
TAT BLAD
RO
E BE UT
E
GING CH
UR
EN
OP RIN
N INJ
ST ENTE
T CA
AC
NT
CO
50
30
33
32
37
31
31
45
47
2005 GC Blower Assembly
35
34
45
49
8
GC-STWC BLOWER HOUSING ASSEMBLY
Ref.
No.
Part
Number
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
04067-07
481547
04019-02
04001-59
04001-01
423298
481428
482300
04024-02
04021-05
04041-07
43277
483209
04021-09
04030-04
423933
04003-05
04001-46
04001-81
04001-21
461928
482379
483189
04043-04
43575
483402
Pin, Ring 2-1/4" Long
Lanyard, Deck Height Pin
Nut, Serr. Flange 1/4-20
Bolt, Hex Head 1/4-20 x 1-1/4"
Bolt, Hex Head 1/4-20 x 3/4"
Belt Cover, Rear
Grip, Blower Lever
Cap, Square
Nut, Push On 3/8 Thread
Lock Nut, 3/8-16
Flatwasher, 3/8-.391 x .938 x .105
Spacer
Pulley, Idler 4" Dia.
Nut, Elastic Stop 3/8-16
Lockwasher, 3/8-16
Plate, Catch Mounting
Bolt, Carr. 3/8-16 x 1-1/2"
Bolt, Hex Head 3/8-16 x 2-1/4"
Bolt, Hex Head 3/8-16 x 3-1/2"
Bolt, Hex Head 3/8-16 x 1-3/4"
Idler Arm Assembly, GC-STT 61"
Belt, GC-STT 61"
Pulley, 4" O.D., GC-STT
Washer, 3/8 Hardened
Pivot, Idler - 61" & 72"
Decal, Belt Cover
9
Ref.
No.
Part
Number
Description
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
04019-04
04001-136
483391
461681
04003-12
04063-06
461796
483034
04019-03
04040-04
421319
48136-02
48135-13
482298
04012-04
461684
481522
43212
04019-03
461419
424094
04062-05
461680
483393
483392
Nut, Serr. Flange 3/8-16
Bolt, Hex Head 3/8-16 x 1-1/2 Gr. 8
Decal, Danger
Blower Housing w/Decals
Bolt, Carr. 5/16-18 x 3/4" Gr. 5
Key, 1/4 x 1/4 x 1-1/2"
Fan Weldment
Bearing Assembly
Nut, Serr. Flange 5/16-18
Flatwasher, 5/16-.344 x .688 x .065
Cover, Blower Housing
Clamp, 8-5/8" Max Dia.
Hose, 8" Dia. x 56" Long
Pulley, 4-3/4" O.D. - 1" Bore
Set Screw, 5/16-18 x 3/8"
Frame, Blower Mount - 61"
Spring, Main Drive
Spacer
Nut, Serr. Flange 5/16-18
Adapter w/Strap
Plate, Blower Catch
Hair Pin Cotter, .243 x 4"
Blower Housing Assembly, GC-STT
Decal, Rotating Blower
Decal, Blower
GC-STWC 61" BLOWER MOUNTING COMPONENTS
10
6
10
11
5
2
4
6
7
1
8
3
6
22
12
9
13
21
14
22
20
15
15
16
18
17
19
RIGHT SIDE OF 61"
CUTTER DECK SHOWN
GC-STWC-61 Blower Attachment Parts
10
GC-STWC 61" BLOWER MOUNTING COMPONENTS
Ref.
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Part
Number
483226
04029-04
482300
04021-08
461723
04040-14
48137-04
04001-59
481625-01
04064-15
04069-03
04067-07
481547
482377
04012-04
04021-07
04030-06
04040-07
04001-71
451413
423826
Description
Belt Cover, GC-STWC - 61"
Wingnut, Plastic 3/8" Small
Cap, Square Vinyl
Nut, Elastic Stop 1/4-20
Adapter, Blower GC-STT
Flatwasher, 1/4-.312 x .750 x .065
Rubber Strap 7-3/4"
Bolt, Hex Head 1/4-20 x 1-1/4"
Knob W/Stud, 3/8-16 x 1-1/4"
Clevis Pin, 5/16 x 1-1/2"
Pin, Rue Cotter 5/16 Dia.
Pin, Ring 1/2 x 2-1/4"
Lanyard
Pulley, 5-1/2" for 61" Deck
Setscrew, 5/16-18 x 3/8"
Nut, Elastic Stop 1/2-13
Lockwasher, 1/2"
Flatwasher, 1/2-.531 x 1.062 x .095
Bolt, Hex Head 1/2-13 x 1-1/2" Grade 5
Mounting Post Weldment, Blower - 61"
Belt Cover, GC-STWC-61
11
GC-STWC BUCKET SUPPORT COMPONENTS (UPPER)
3
36
37
35
1
6
4
2
5
3
9
11
8
33
4
33
5
23
23
32
21 22
16
5
31
9
13
18
19
9
5
16
21
13
16
18
20
16
24
11
14 16
5
4
5
38
9
35
16
25
17
31
9
34
15
30
27
32
29
26
28
12
40
7
12
10
39
GC-STWC BUCKET SUPPORT COMPONENTS (UPPER)
Ref.
No.
Part
Number
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
423302
04090-02
04041-19
04001-32
04041-01
461408
04001-117
423258
04021-09
04040-11
04001-46
04021-11
04001-20
04001-135
451674
04019-04
04090-03
43546
482304
423436
43212
04021-05
43277
423259
423261
48135-13
48136-02
482422
482421
04001-10
04021-10
04040-15
04041-11
04030-04
482409
04010-25
04021-01
04001-08
451517
461097
Screen, Catcher Hood
Pop Rivet, 3/16 x .652
Flatwasher, 3/16-.196 x .469 x .048
Bolt, Hex Head 3/8-16 x 1-1/4"
Flatwasher, 3/8-.391 x .938 x .105
Hood Assembly, GC-STT (includes items 1, 2 & 3 and items 2 & 15 on page 14)
Bolt, Hex Head 7/16-14 x 1-3/4"
Hinge, Upper LH
Nut, Elastic Stop 3/8-16
Flatwasher, 7/16-.500 x 1-1/4"
Bolt, Hex Head 3/8-16 x 2-1/4"
Nut, Elastic Stop 7/16-14
Bolt, Hex Head 3/8-16 x 1-1/2"
Bolt, Hex Head 3/8-16 x 1-3/4" Grade 8
Support Weldment, Bag Frame
Nut, Serrated Flange 3/8-16
Rivet, 3/16 x .402 POP
Bushing, Hopper Pivot
Spring, Hood Hinge
Hinge, Lower LH
Spacer
Locknut, 3/8-16
Spacer
Hinge, Upper RH
Hinge, Lower RH
Hose, 8" Dia. x 56" (61")
Clamp, 8-5/8" Max Dia. (61")
Tube, Filler (8" Hose)
Elbow (8" Hose)
Bolt, Hex Head 5/16-18 x 1-1/4"
Nut, Elastic Stop 5/16-18
Flatwasher, 5/16-.375 x .875 x .083
Flatwasher, 3/8- .406 x 1-1/2" x .179
Lockwasher, 3/8" Spring
Latch
Screw, #10-32 x 3/4"
Nut, Elastic Stop #10-32
Bolt, Hex Head 5/16-18 x 3/4"
Support Weldment, Weights
Weight Assembly
13
GC-STWC BUCKET SUPPORT COMPONENTS (LOWER)
1
2
24
22
23
21
20
19
18
"A"
3
4
5
17
11
6
16
7
15
TO "A" 4
13
4
5
4
8
6
14
7
12
3
4
8
FRAME
6
9
5
6
25
26
9
10
10A
STC 2008 BSC
14
GC-STWC BUCKET SUPPORT COMPONENTS (LOWER)
Ref.
No.
Part
Number
Description
1
2
3
4
5
6
7
8
9
10
10A
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
04090-02
482321
423262
04041-07
04021-09
04020-04
04021-05
04067-07
04001-19
461995
461994
04021-02
04001-46
04001-31
482569
423312
451674
04003-02
04001-08
423198
04003-12
423197
04019-03
04040-15
04021-10
04001-32
451969
Pop Rivet, 3/16 x .652
Seal, Hood
Tube, Upright
Flatwasher, 3/8-.391 x .938 x .105
Nut, Elastic Stop 3/8-16
Nut, 3/8-16
Hex Lock Nut, 3/8-16
Pin, Ring 1/2 x 2-1/4"
Bolt, Hex Head 3/8-16 x 1"
Mounting Bracket Weldment RH
Mounting Bracket Weldment LH
Lock Nut, 1/4-20 Center
Bolt, Hex Head 3/8-16 x 2-1/4"
Bolt, Hex Head 3/8-16 x 2-1/2"
Bag Assembly, GC-STT
Retainer, Seal
Support, Bag Frame
Bolt, Carr. 1/4-20 x 3/4"
Bolt, Hex Head 5/16-18 x 3/4"
Mount, Bag Frame Tube
Bolt, Carr. 5/16-18 x 3/4"
Tube, Bag Support
Nut, Serr. Flange 5/16-18
Flatwasher, 5/16-.375 x .875 x .083
Nut, Elastic Stop 5/16-18
Bolt, Hex Head 3/8-16 x 1-1/4"
Muffler Guard
15
GC-STWC DECALS
483402
482275
MANUFACTURED UNDER ONE OR MORE
OF THE FOLLOWING PATENTS:
4,487,006
4,991,382
5,133,176
6,192,666
7,065,946
4,885,903
4,998,948
5,826,416
6,766,633
4,920,733
5,042,239
5,832,708
6,892,519
4,967,543
5,117,617
5,865,018
6,996,962
PATENTS PENDING
483044
481327
483392
483392
483391
483391
483393
483393
16
LIMITED WARRANTY- COMMERCIAL ACCESSORY
Any part of the Scag commercial accessory manufactured by Scag and found, in the reasonable judgment of Scag,
to be defective in material or workmanship, will be repaired or replaced by an Authorized Scag Service Dealer without
charge for parts and labor.
The Scag accessory, including any defective part, must be returned to an Authorized Scag Service Dealer within
the warranty period. The expense of delivering the accessory to the dealer for warranty work and the expense of
returning it back to the owner after repair or replacement will be paid for by the owner. Scag’s responsibility in respect
to claims is limited to making the required repairs or replacements, and no claim of breach of warranty shall be cause
for cancellation or rescission of the contract of sale of any Scag machine. Proof of purchase will be required by the
dealer to substantiate any warranty claim. All warranty work must be performed by an Authorized Scag Service
Dealer.
This warranty is limited to 90 days from the date of original retail purchase for any Scag accessory that is used for
commercial purposes, or any other income-producing purpose including rental use.
The warranty for the blower assembly (excluding the belt) is limited to 1-year from the date of original retail
purchase. 90 Days for rental use.
This warranty does not cover any accessory that has been subject to misuse, neglect, negligence, or accident,
or that has been operated in any way contrary to the operating instructions as specified in the Operator's Manual.
The warranty does not apply to any damage to the accessory that is the result of improper maintenance, or to
any accessory or parts that have not been assembled or installed as specified in the Operator's Manual.
The warranty does not cover any accessory that has been altered or modified. In addition, the warranty does not
extend to repairs made necessary by normal wear, or by the use of parts or accessories which, in the reasonable
judgment of Scag, are either incompatible with the Scag mower or adversely affect its operation, performance or
durability. This warranty does not cover engines and electric starters, which are warranted separately by their
manufacturer.
Scag Power Equipment reserves the right to change or improve the design of any accessory without assuming any
obligation to modify any accessory previously manufactured.
All other implied warranties are limited in duration to the 90 day warranty period. Accordingly, any such implied
warranties including merchantability, fitness for a particular purpose, or otherwise, are disclaimed in their entirety
after the expiration of the appropriate ninety day warranty period. Scag’s obligation under this warranty is strictly
and exclusively limited to the repair or replacement of defective parts and Scag does not assume or authorize anyone
to assume for them any other obligation. Some states do not allow limitations on how long an implied warranty lasts,
so the above limitation may not apply to you.
Scag assumes no responsibility for incidental, consequential or other damages including, but not limited to, expense
for gasoline, oil, expense of delivering the machine to an Authorized Scag Service Dealer and expense of returning
it back to the owner, mechanic’s travel time, telephone or telegram charges, rental of a like product during the time
warranty repairs are being performed, travel, loss or damage to personal property, loss of revenue, loss of use of
the mower, loss of time, or inconvenience. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
© 2007
SCAG POWER EQUIPMENT
DIVISION OF METALCRAFT OF MAYVILLE, INC
WWW.SCAG.COM
PART NO. 03229
PRINTED 3-2007
PRINTED IN USA