Roland INTEGRA-7 Editor Owner`s manual

INTEGRA-7 Editor for iPad Owner’s Manual
Copyright © 2012 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION
1PS
What Is INTEGRA-7 Editor for iPad?
“INTEGRA-7 Editor for iPad” is an iPad app that lets you edit the parameters of the Roland INTEGRA-7.
The app lets you edit parameters while benefiting from the superior legibility of the iPad, made possible thanks to its high-resolution display. All you have to do is
connect your iPad to the INTEGRA-7, using either USB or a wireless LAN.
Your parameter edits are sent to the INTEGRA-7, and the changes in the parameter settings are reflected on the INTEGRA-7 in real time.
The graphical editing screen allows visual control of the parameters.
“INTEGRA-7 Editor for iPad” lets you do the following:
• Edit parameters such as level, pan, and EQ for each part in the Mixer and Part View screens
• Use MOTIONAL SURROUND to control the spatial position of each part
• Edit the parameters of SuperNATURAL Synth Tones
• Load expansion sounds
• Save StudioSets and SuperNATURAL Synth Tones to the USER bank of the INTEGRA-7
IMPORTANT NOTES
Trademarks
•Roland and SuperNATURAL are either registered trademarks or trademarks of Roland Corporation in the United States and other countries.
•Company names and product names appearing in this document are registered trademarks or trademarks of their respective owners.
Additional Precautions
•Unfortunately, it may be impossible to restore the contents of data that was stored in the iPad once it has been lost. Roland Corporation assumes no liability concerning such loss of
data.
•In the interest of product improvement, the specifications and/or contents of this package are subject to change without prior notice.
2
Contents
What Is INTEGRA-7 Editor for iPad? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
IMPORTANT NOTES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Settings in INTEGRA-7 Editor for iPad. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Connecting Via a USB Cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Required Items. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting Your Equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Making Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
5
5
5
Connecting Via Wireless LAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
What Is Wireless LAN Function?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Settings for Your Instrument. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Making Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
6
6
6
About the Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
How the Screens Are Organized. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
About READ and WRITE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
READ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
WRITE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Studio Set Mixer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Part View. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
MOTIONAL SURROUND. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
SuperNATURAL Synth Tone Edit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Editing a INTEGRA-7 Synth Tone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Saving the Synth Tone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3
Settings in INTEGRA-7 Editor for iPad
Tap the [
] button in the upper-right part of the screen in INTEGRA-7 Editor for iPad.
The setup screen will appear.
Parameter
Mode Select
Motional Surround View Type
Value
Explanation
Demo
Choose this when you want to try out operation without connecting the INTEGRA-7.
Normal
The app will work in connection with the INTEGRA-7.
In most cases, you’ll want to use the app in Normal mode.
Detail
Shows a graphic for the instrument whose part icon is selected in the MOTIONAL SURROUND
screen.
Simple
Shows a simple indication of the part icons in the MOTIONAL SURROUND screen.
Motional Surround Direct Jump OFF, ON
If this is on, you can specify the spatial position of the current part simply by touching the spatial
position area.
Set this to the same value as the Device ID in “INTEGRA-7 settings”
Device ID
17–32
Checking the Device ID
Note the value shown under [MENU]
“System”
MIDI Device
Selects the MIDI device.
Manual
Tap this to view the operating manual (this document).
Version
Shows the version of INTEGRA-7 Editor for iPad that you’re using.
4
“MIDI” tab
Device ID.
Connecting Via a USB Cable
Required Items
If you’re connecting via a USB cable, you’ll need the following items.
• INTEGRA-7
5. Hold down the [SHIFT] button and press the [EDIT] button to save
the system settings.
6. Restart the INTEGRA-7.
MEMO
The saved system settings will take effect when you restart the INTEGRA-7.
• Apple iPad Camera Connection Kit (Camera Connector, made by Apple Inc.)
• USB cable (type-A male – type-B male: commercially available)
Settings in INTEGRA-7 Editor for iPad
1. In the upper right of the screen, tap the [
] button.
The setup screen (p. 4) will appear.
2. Set the device ID to the same setting as on the INTEGRA-7. (By
default, this will be 17.)
Connecting Your Equipment
1. Connect the Apple iPad Camera Connection Kit (Camera Connector,
made by Apple Inc.) to the iPad.
2. Use a USB cable (commercially available) to connect the USB
connector of the Apple iPad Camera Connection Kit to the
INTEGRA-7’s USB COMPUTER port.
Making Connections
INTEGRA-7 settings
1. Press the [MENU] button.
2. Choose “System,” and press the [ENTER] button.
Checking the device ID of the INTEGRA-7
Note the value shown under [MENU]
“System”
“MIDI” tab
Device ID.
3. Choose the INTEGRA-7 as the MIDI device.
4. Tap somewhere other than in the setup screen.
The setup screen will disappear.
5. Press the [READ] button (p. 10).
The current parameter settings of the INTEGRA-7 will be read in, and all
parameters of INTEGRA-7 Editor for iPad will be updated.
MEMO
When you connect the INTEGRA-7 sound module to
INTEGRA-7 Editor for iPad, tap the [READ] button first to synchronize the
settings.
3. Choose the “SETUP” tab.
4. Set the “USB Driver” parameter to “GENERIC (MIDI only).”
5
Connecting Via Wireless LAN
What Is Wireless LAN Function?
Making Connections
By inserting the wireless USB adapter (WNA1100-RL; sold separately) into the
INTEGRA-7’s USB MEMORY port, you’ll be able to use this app via wireless LAN.
iPad
Wireless LAN access point
(e.g., wireless LAN router)
INTEGRA-7
1. Make wireless settings on the INTEGRA-7.
For details, refer to the Roland website ( http://www.roland.com/manuals/)
product name (INTEGRA-7) “About the Wireless LAN Function.”
2. In the WiFi section of the iPad setup screen, turn the WiFi switch ON.
Wireless USB adapter
(sold separately: WNA1100RL)
Wireless LAN
Wireless LAN
What you’ll need in order to use the wireless LAN function
‰‰Electronic musical instrument (Roland INTEGRA-7)
‰‰Wireless USB adapter (Roland WNA1100-RL)
‰‰A wireless LAN access point (such as a wireless LAN router) that supports
WPS
Settings for Your Instrument
For details on making settings for your instrument, refer to the Roland website
( http://www.roland.com/manuals/ ) model name (INTEGRA-7)
“About the Wireless LAN Function.”
3. In the “Choose a network” field, select the name of the router you’re
using.
If you want to connect in Ad-Hoc mode, choose INTEGRA-7_(WirelessID) and
enter Ad-Hoc Key as the password.
4. Start up INTEGRA-7 Editor for iPad.
5. In the upper right of the screen, tap the [
] button.
The setup screen (p. 4) will appear.
6. As the MIDI device, choose INTEGRA-7_(WirelessID).
If your INTEGRA-7’s Wireless ID is still in the default state, it will be shown as
INTEGRA-7.
7. Tap somewhere other than in the setup screen.
The setup screen will disappear.
8. Press the [READ] button (p. 10).
The current parameter settings of the INTEGRA-7 will be read in, and all
parameters of INTEGRA-7 Editor for iPad will be updated.
MEMO
When you connect the INTEGRA-7 sound module to
INTEGRA-7 Editor for iPad, tap the [READ] button first to synchronize the
settings.
6
Connecting Via Wireless LAN
If INTEGRA-7_(WirelessID) Is Not Shown as a MIDI Device, Check the Following Points.
Points to check
Reference
Is the instrument powered-on?
Is the wireless USB adapter (WNA1100-RL) connected to the instrument?
Are you using an instrument that
supports wireless LAN functionality?
Is the instrument connected to the
wireless LAN?
Are the instrument and the iPad
connected to the same network (the
same wireless LAN access point)?
Is the wireless LAN access point set to
allow communication between wireless
LAN devices?
For details on models that support wireless LAN
functionality, refer to
http://roland.jp/link/RWC/e/ .
For details on making settings for your instrument,
refer to the Roland website
( http://www.roland.com/manuals/ )
model name (INTEGRA-7)
“About the Wireless LAN Function.”
Refer to the owner’s manual of your wireless LAN
access point for details on settings.
7
About the Screen
INTEGRA-7 Editor for iPad consists of the following four screens.
Studio Set Mixer screen (p. 11)
Part View screen (p. 12)
MOTIONAL SURROUND screen (p. 13)
SuperNATURAL Synth Tone Edit screen (p. 14)
8
About the Screen
How the Screens Are Organized
Access buttons for each screen
Press these buttons to access the corresponding
screen.
Button
Screen
Studio Set Mixer
page 11
Part View
page 12
MOTIONAL
SURROUND
page 13
[READ] button
Loading sound data into EXPANSION virtual slots
Drag a sound data graphic
from EXPANSION SOUNDS
into the EXPANSION virtual
slot, and then tap the
EXPANSION
[LOAD] button.
Virtual Slots
When you tap this button, the current settings for
the INTEGRA-7’s parameters will be read in, updating
all parameters within INTEGRA-7 Editor for iPad.
EXPANSION
SOUNDS
Drag
SuperNATURAL Synth
page 14
Tone Edit
When you connect the INTEGRA-7 sound module
to INTEGRA-7 Editor for iPad, tap the [READ] button
first to synchronize the settings.
[WRITE] button
Press this button to access a screen that lets you
save the settings of INTEGRA-7 Editor for iPad as an
INTEGRA-7 Studio Set or Tone.
[LOAD] button
STUDIO SET
MIDI indicator
Shows the studio set name.
This will light when MIDI messages are being
transmitted or received.
Tap “
” to see a list of studio sets.
Setup screen display area
[Setup] button
[PART] buttons
These buttons switch the current part (the part
that’s selected).
When you tap a part number, its frame will turn
orange and it will become the current part.
Accesses the setup screen of
INTEGRA-7 Editor for iPad.
TONE
Shows the tone of the current part.
TYPE
Shows the tone type.
[PREVIEW] switch
NAME
If you move this switch downward, the switch will
be held and the preview will continue playing.
Shows the tone name.
Tap “
” to see a list of tones.
9
About READ and WRITE
READ
WRITE
This updates all parameters within INTEGRA-7 Editor for iPad by reading in the
current parameter settings from the INTEGRA-7 sound module.
This saves the Studio Set parameters or Tone parameters into the USER bank
of the INTEGRA-7 sound module.
If you’ve edited parameters by operating the INTEGRA-7 itself (rather than
INTEGRA-7 Editor for iPad), differences will arise in the parameter settings of
the two systems; in this case, you must tap the [READ] button to reconcile the
differences.
The Studio Set parameters include all the editable parameters of the
MOTIONAL SURROUND, StudioSet Mixer, and Part View screens.
After connecting the INTEGRA-7 and INTEGRA-7 Editor for iPad, tap the
[READ] button to synchronize the two systems before you proceed.
The Tone parameters are only those of SuperNATURAL Synth Tones.
When you tap the [WRITE] button, the following screen will appear.
1. Tap the [STUDIO SET] button or the [TONE] button to specify the
data that you want to save.
2. In the save-destination list, tap the desired save destination to select
it.
3. Tap the [EXECUTE] button.
[STUDIO SET] button, [TONE] button
[WRITE] button
Select what you wish to save.
Accesses the Write screen.
[EXECUTE] button
Save-destination list
Saves the data.
Select the save destination in the list.
The list shows the tone’s type, bank, number,
name, and category.
10
Studio Set Mixer
Here you can edit each part’s volume, pan, equalizer, and mute settings, as well as the overall volume and equalizer settings.
Part numbers of the studio set
MASTER LEVEL
[EQ] button
By flicking the screen to left or right you can switch the parts
that are shown.
Adjusts the volume and equalizer settings of the entire
INTEGRA-7.
This accesses the 3-band equalizer screen.
[PAN] knob
Specifies the left/right position of each part’s sound.
[MUTE] switch
Turn this on if you don’t want a part to be heard.
MUTE Switch
Explanation
Mute is on
(The part’s sound will not be heard.)
Mute is off
(The part’s sound will be heard.)
Level slider
Sound name
Adjusts the volume of each part.
Shows the name of each part’s sound.
11
Equalizer settings can be edited individually for each
part.
Part View
Here you can view or edit each part’s sound name, volume, pan, effect, MIDI channel, and mute settings.
Tone information
Part parameter
Item
Explanation
Parameter
Explanation
PART
Indicates the part number.
TONE
Touch a tone name in the screen to access the tone select screen.
TYPE
Indicates the type of tone.
BANK
Indicates the tone bank.
CATEGORY
Indicates the tone category.
Tone Select screen
You can view the tone list by category or by bank. Use the [BY CATEGORY] button and [BY TONE & BANK] button
to switch between views.
Tone list shown by category
Tone list shown by bank
Part parameters
You can edit the following parameters by dragging the
corresponding item in the screen.
Parameter
Explanation
LEVEL
Specifies the part’s volume.
PAN
Localizes the part’s sound.
CHORUS
Specifies the chorus send level.
REVERB
Specifies the reverb send level.
CH
Specifies the MIDI channel.
Parameter
Explanation
MUTE
Switches mute on/off each time you touch this.
Button
Explanation
[BY CATEGORY]
Shows the tone list organized by category.
When you select a category icon in the left side of the screen, the
right side will show a list of tones in the selected category.
[BY TONE & BANK]
Shows the tone list organized by bank.
When you select a bank icon in the left side of the screen, the right
side will show a list of tones in the selected bank.
Tap a tone name in the tone list to select it, and then tap the [Close] button to close the Tone Select screen.
12
MOTIONAL SURROUND
The MOTIONAL SURROUND screen is organized as follows.
Sound position
Setup button
Drag each part’s icon to change the spatial position of the sound.
Accesses the setup screen of INTEGRA-7 Editor for iPad (p. 4)
Direct jump
Simply display
If this function is turned on,
you can specify the spatial
position of the current part
simply by touching the sound
position area.
MOTIONAL SURROUND Switch
Turns MOTIONAL SURROUND on/off.
AMBIENT TYPE
Selects the type of ambience.
LEFT<>RIGHT
Type
Explanation
Specifies the left/right position of the sound in terms of a numerical value.
L64 (left)–0 (center)–63R (right)
ROOM 1, 2
Reverberation typically heard when performing in a room.
HALL 1, 2
Reverberation typically heard when performing in a concert hall.
FRONT<>BACK
Specifies the front/back position of the sound in terms of a numerical value.
F63 (front)–0 (center)–64B (back)
ROOM SIZE
Specifies the size of the room whose ambience is being simulated.
Type
Explanation
LARGE
Large room
MEDIUM
Between the large and small rooms
SMALL
Small room
13
SuperNATURAL Synth Tone Edit
The SuperNATURAL Synth Tone Edit screen is organized as follows.
Partial SW
Setup button
Turn each partial on/off.
Displays INTEGRA-7 Editor for iPad’s setup screen (p. 4).
Button
Explanation
This partial is on.
This partial is off.
Partial SELECT
Select the partial that you want to edit.
Button
Parameters
Here you can edit the Synth Tone
Explanation
parameters (p. 15).
This partial is being edited.
This partial is not being edited.
CATEGORY
This shows the category of the tone.
Common
Here you can switch among parameters to be edited, and make settings for parameters that are common to the entire Synth Tone.
Parameter select tabs
Parameter name and value
Use these to switch between types of
parameter that you want to edit.
This shows the name and value of the
most recently edited parameter.
COMMON parameters
These parameters are common within the
layer that you’re editing.
**The explanations in this manual include illustrations that depict what should typically be shown by the display.
Note, however, that your unit may incorporate a newer, enhanced version of the system (e.g., includes newer sounds), so what you actually see in the display may not
always match what appears in the manual.
14
SuperNATURAL Synth Tone Edit
Parameters
Here you can edit the Synth Tone parameters. The screen that’s shown will depend on the parameter select tab you’ve chosen.
OSC/FILTER/AMP
This will appear if the parameter select tab is set to “OSC/FILTER/AMP” (p. 14).
OSC (Oscillator)
The oscillator generates the waveform that forms the basis of the sound.
Here you can select a waveform and also specify its pitch.
Each tone has one oscillator. You can use them individually, or use three in combination to create
thick or complex sounds.
FILTER (Filter)
The filter parameters modify the tone quality of the sound. You can vary the tone quality by editing
the filter parameters.
The filter types include a low-pass filter (LPF), which passes only the region of sound that’s below
the specified frequency (cutoff frequency), and a high-pass filter (HPF), which passes only the region
that’s above the specified frequency.
AMP (Amp)
The amp parameters control the volume. Raising these values will increase the volume.
LFO
This will appear if the parameter select tab is set to “LFO” (p. 14).
LFO
LFO stands for Low Frequency Oscillator, an oscillator that operates at a very slow rate. It can produce
various waveforms, including sine, triangle, square, and sawtooth waves.
By using the LFO to modulate audio signals, you can add effects such as vibrato or tremolo.
MODULATION LFO
These parameters specify how the LFO is to be applied when you move the pitch bend/modulation
lever. Make settings in the same way as for the LFO.
15
SuperNATURAL Synth Tone Edit
Editing a INTEGRA-7 Synth Tone
Here’s how to read the settings of a Synth Tone from the INTEGRA-7 into INTEGRA-7 Editor for iPad, and edit those settings.
1. Tap the [READ] button.
The Synth Tone parameters will be sent from the INTEGRA-7 to INTEGRA-7 Editor for iPad. The current Synth Tone parameter settings of the INTEGRA-7 will appear in
INTEGRA-7 Editor for iPad.
MEMO
If you’ve operated the INTEGRA-7 itself, tap the [READ] button. The current state of the INTEGRA-7 will be read into INTEGRA-7 Editor for iPad.
2. Edit the parameters.
The edited parameters will be sent to the INTEGRA-7. Parameter settings are reflected on the INTEGRA-7 in real time.
Buttons and switches
[READ] button
Tap a button or switch to change its
setting.
PCM number
If tapped when PCM has been selected
for WAVE, the WAVE NUMBER popup will
appear.
Knobs and sliders
Drag a knob or slider up/down to
change its value.
MEMO
•• Make fine adjustments to the value by
dragging to left or right.
•• You can reset the value to its initial
state by rapidly tapping three times.
16
SuperNATURAL Synth Tone Edit
MEMO
• Parameter editing supports the “multi-touch” capability of the iPad. You can edit multiple parameters simultaneously.
• For details on the tone parameters, refer to the PDF manual “INTEGRA-7 Parameter Guide.” The PDF manual can be downloaded from the Roland website
“Support Information.”
Roland website “Support Information”
http://www.roland.com/support/
Saving the Synth Tone
A Synth Tone you edit is temporary; it will be lost if you turn off the power or select another tone. If you want to keep a Synth Tone you’ve edited, save it to the
INTEGRA-7’s USER bank.
1. Tap the [WRITE] button.
The Write screen will appear.
2. Select the save destination, and tap the [EXECUTE] button.
If you decide to cancel without saving, tap the [x] button to close the Write screen.
[STUDIO SET] button, [TONE] button
[WRITE] button
Select what you wish to save.
Accesses the Write screen.
[EXECUTE] button
Save-destination list
Saves the data.
Select the save destination in the list.
The list shows the tone’s type, bank, number,
name, and category.
17