Cisco 1805-D - 1805 Integrated Services Router Installation guide

Release Notes for
Cisco Configuration Professional 2.7
April 29, 2013
OL-29505-01
This Release Notes document supports Cisco Configuration Professional version 2.7. This document
should be used with the documents listed in the “Related Documentation” section.
This document is updated as needed. To ensure that you have the latest version of this Release Notes
document, go to http://www.cisco.com/go/ciscocp. Choose Release and General Information >
Release Notes, and locate the latest release notes pertaining to your release.
Contents
This document contains the following sections:
•
Introduction, page 2
•
System Requirements, page 2
•
New and Changed Information, page 20
•
Limitations and Restrictions, page 23
•
Important Notes, page 24
•
Caveats, page 27
•
Related Documentation, page 35
•
Glossary, page 36
Cisco Systems, Inc.
www.cisco.com
Introduction
Introduction
The Cisco Configuration Professional is a GUI-based device management tool for Integrated Service
Routers. Cisco Configuration Professional simplifies the router, Firewall, Intrusion Prevention System,
VPN, Unified Communications, WAN, and basic LAN configurations through GUI-based, easy-to-use
wizards. The Cisco Configuration Professional is installed on a PC.
Routers that are ordered with Cisco Configuration Professional are shipped with Cisco Configuration
Professional Express installed on the router flash memory. Cisco Configuration Professional Express is
a light-weight version of Cisco Configuration Professional that you can use to configure LAN and WAN
interfaces.
System Requirements
This section describes PC and router system requirements. It contains the following sections:
•
PC System Requirements, page 2
•
Router System Requirements, page 3
•
Cisco Configuration Professional Ordering Options, page 20
PC System Requirements
Table 1 lists the system requirements for a PC running Cisco Configuration Professional. Although
Cisco Configuration Professional requires Java Runtime Environment (JRE) to run, the Cisco
Configuration Professional application included with Cisco Configuration Professional can run under
the native Java Virtual Machine on the supported browsers and JRE.
Table 1
PC System Requirements
System Component
Requirement
Processor
2 GHz processor or faster
Random Access Memory
1 GB DRAM minimum; 2 GB recommended
Hard disk available memory
400 MB
Operating System
Any of the following:
•
Microsoft Windows 7-32 and 64 bit
•
Microsoft Windows Vista Business Edition
•
Microsoft Windows Vista Ultimate Edition
•
Microsoft Windows XP with Service Pack 3-32 bit
•
Mac OSX 10.5.6 running Windows XP using VMWare 2.0
Browser
Internet Explorer 6.0 or higher
Screen Resolution
1024 X 768
Java Runtime Environment
JRE Versions 1.6.0_11 up to Version 1.7.0_17
Adobe Flash Player
Version 10.0 or later, with Debug set to “No”
Release Notes for Cisco Configuration Professional 2.7
2
OL-29505-01
System Requirements
Router System Requirements
The Router System requirements are described in the following sections:
•
Supported Routers, page 3
•
Supported Phones, page 11
•
Supported Modules and Cards, page 12
•
Connected Grid, page 17
•
Determining the Cisco IOS Release, page 18
•
Required IP Address Configuration Information, page 19
•
Router Configuration Requirements, page 19
Supported Routers
Table 2 lists the routers that Cisco Configuration Professional supports.
Table 2
Supported Routers
Supported Routers
Cisco 815 Series
CISCO815
CISCO815-VPN-K9
Cisco 819 Series
C819G-U-K9
C819G-V-K9
C819G-S-K9
C819G-B-K9
C819HG+7-K9
C819HG-U-K9
C819HG-V-K9
C819HG-S-K9
Cisco 851 Series
CISCO851-K9
CISCO851W-G-A-K9
CISCO851W-G-E-K9
CISCO851W-G-J-K9
Cisco 857 Series
CISCO857-K9
CISCO857W-G-A-K9
CISCO857W-G-E-K9
Cisco 861 Series
Release Notes for Cisco Configuration Professional 2.7
OL-29505-01
3
System Requirements
Table 2
Supported Routers (continued)
Supported Routers
CISCO861-K9
CISCO861W-GN-A-K9
CISCO861W-GN-E-K9
CISCO861W-GN-P-K9
Cisco 866 Series
CISCO866VAE
CISCO866VAE-K9
Cisco 867 Series
CISCO867-K9
CISCO867VA-K9
CISCO867VAE
CISCO867VAE-K9
CISCO867W-GN-A-K9
CISCO867W-GN-E-K9
Cisco 871 Series
CISCO871-K9
CISCO871W-G-A-K9
CISCO871W-G-E-K9
CISCO871W-G-J-K9
Cisco 876 Series
CISCO876-K9
CISCO876W-G-E-K9
Cisco 877 Series
CISCO877-K9
CISCO877-M-K9
CISCO877W-G-A-K9
CISCO877W-G-E-K9
CISCO877W-G-E-M-K9
Cisco 878 Series
CISCO878-K9
CISCO878W-G-A-K9
CISCO878W-G-E-K9
Cisco 881 Series
Release Notes for Cisco Configuration Professional 2.7
4
OL-29505-01
System Requirements
Table 2
Supported Routers (continued)
Supported Routers
C881W-A-K9
C881W-E-K9
CISCO881-K9
CISCO881W-GN-A-K9
CISCO881W-GN-E-K9
CISCO881W-GN-P-K9
CISCO881W-A-K9
CISCO881W-E-K9
CISCO881G-K9
CISCO881GW-GN-A-K9
CISCO881GW-GN-E-K9
CISCO881G-S-K9
CISCO881G-V-K9
CISCO881G-A-K9
C881G-U-K9
C881G-S-K9
C881G-V-K9
C881G-B-K9
C881G+7-K9
C881G+7-A-K9
C881SRST-K9
C881SRSTW-GN-A-K9
C881SRSTW-GN-E-K9
CISCO881-V-K9
CISCO881WD-A-K9
CISCO881WD-E-K9
CISCO881GW+7-A-K9
CISCO881GW+7-E-K9
CISCO881GW-S-A-K9
CISCO881GW-V-A-K9
Cisco 886 Series
Release Notes for Cisco Configuration Professional 2.7
OL-29505-01
5
System Requirements
Table 2
Supported Routers (continued)
Supported Routers
CISCO886-K9
CISCO886G-K9
CISCO886VA-K9
C886VA-W-E-K9
C886VAG+7-K9
CISCO886GW-GN-E-K9
Cisco 887 Series
CISCO887-K9
CISCO887VA-K9
CISCO887VA-M-K9
C887VA-W-A-K9
C887VA-W-E-K9
C887VAM-W-E-K9
C887VAG-S-K9
C887VAG+7-K9
C887VAMG+7-K9
CISCO887W-GN-A-K9
CISCO887W-GN-E-K9
CISCO887M-K9
CISCO887MW-GN-E-K9
CISCO887G-K9
CISCO887GW-GN-A-K9
CISCO887GW-GN-E-K9
CISCO887V-K9
CISCO887VW-GNA-K9
CISCO887VW-GNE-K9
CISCO887VG-K9
CISCO887VGW-GNA-K9
CISCO887VGW-GNE-K9
CISCO877VA-GW+7-A-K9
CISCO877VA-GW+7-E-K9
CISCO877VA-WD-A-K9
CISCO877VA-WD-E-K9
CISCO877VA-V-K9
CISCO877VA-V-W-E-K9
Release Notes for Cisco Configuration Professional 2.7
6
OL-29505-01
System Requirements
Table 2
Supported Routers (continued)
Supported Routers
Cisco 888 Series
CISCO888-K9
CISCO888E-K9
CISCO888EA-K9
CISCO888W-GN-A-K9
CISCO888W-GN-E-K9
CISCO888E-K9
CISCO888EW-GNA-K9
CISCO888EW-GNE-K9
CISCO888G-K9
CISCO888GW-G-NA-K9
CISCO888GW-G-NE-K9
C888EG+7-K9
C888SRST-K9
C888SRSTW-GN-A-K9
C888SRSTW-GN-E-K9
Cisco 891 Series
CISCO891-K9
CISCO891W-AGN-A-K9
CISCO891W-AGN-N-K9
Cisco 892 Series
CISCO892-K9
CISCO892F-K9
CISCO892FW-A-K9
CISCO892FW-E-K9
CISCO892W-AGN-E-K9
Cisco 1801
CISCO1801
CISCO1801/K9
CISCO1801-M
CISCO1801-M/K9
CISCO1801W-AG-B/K9
CISCO1801W-AG-C/K9
CISCO1801W-AG-N/K9
CISCO1801WM-AGB/K9
Release Notes for Cisco Configuration Professional 2.7
OL-29505-01
7
System Requirements
Table 2
Supported Routers (continued)
Supported Routers
Cisco 1802
CISCO1802
CISCO1802/K9
Cisco 1803
CISCO1803/K9
CISCO1803W-AG-B/K9
CISCO1803W-AG-E/K9
Cisco 1805
CISCO1805-D
CISCO1805-D/K9
CISCO1805-EJ
Cisco 1811
CISCO1811/K9
CISCO1811W-AG-B/K9
CISCO1811W-AG-C/K9
CISCO1811W-AG-N/K9
Cisco 1812
CISCO1812/K9
CISCO1812-J/K9
CISCO1812 W-AG-C/K9
CISCO1812W-AG-P/K9
Cisco 1841
CISCO1841
Cisco 1861
Release Notes for Cisco Configuration Professional 2.7
8
OL-29505-01
System Requirements
Table 2
Supported Routers (continued)
Supported Routers
CISCO1861-SRST-B/K9
CISCO1861-SRST-C-B/K9
CISCO1861-SRST-C-F/K9
CISCO1861-SRST-F/K9
CISCO1861-UC-2BRI-K9
CISCO1861-UC-4FXO-K9
CISCO1861E-SRST-B/K9
CISCO1861E-SRST-C-B/K9
CISCO1861E-SRST-C-F/K9
CISCO1861E-SRST-F/K9
CISCO1861E-UC-2BRI-K9
CISCO1861E-UC-4FXO-K9
CISCO1861W-SRST-C-B/K9
CISCO1861W-SRST-C-F/K9
CISCO1861W-SRST-B/K9
CISCO1861W-SRST-F/K9
CISCO1861W-UC-2BRI-K9
CISCO1861W-UC-4FXO-K9
Cisco 1921
CISCO1921/K9
Cisco 1941
CISCO1941/K9
CISCO1941W-A/K9
CISCO1941W-C/K9
CISCO1941W-E/K9
CISCO1941W-N/K9
CISCO1941W-P/K9
Cisco 2800 Series
CISCO2801
CISCO2811
CISCO2821
CISCO2851
Cisco 2900 Series
Release Notes for Cisco Configuration Professional 2.7
OL-29505-01
9
System Requirements
Table 2
Supported Routers (continued)
Supported Routers
CISCO2901/K9
CISCO2911/K9
CISCO2921/K9
CISCO2951/K9
Cisco 3800 Series
CISCO3825
CISCO3825-NOVPN
CISCO3845
CISCO3845-NOVPN
Cisco 3900 Series
CISCO3925/K9
CISCO3925E/K9
CISCO3945/K9
CISCO3945E/K9
Release Notes for Cisco Configuration Professional 2.7
10
OL-29505-01
System Requirements
Supported Phones
Table 3 lists the phones that Cisco Configuration Professional supports.
Table 3
Supported Phones
Supported Phones
Supported Expansion
Modules
Supported
Conference Stations
3905
—
—
7902G
7914
7935
7905
7915-12
7936
7906G
7915-24
7937G
7910G
7916-12
7911G
7916-24
6901
6911
6921
6941
6945
6961
7912G
7920
7921G
7931G
7940G
—
—
—
—
7941G
7941G-GE
7942G
7945G
7960G – compatible expansion module (7914)
7961G – compatible expansion module (7914)
7961G-GE
7962G – compatible expansion module (7915, 7916)
7965G – compatible expansion module (7915, 7916)
7970G – compatible expansion module (7914)
7971G – compatible expansion module (7914)
7975G – compatible expansion module (7915, 7916)
7985G
Release Notes for Cisco Configuration Professional 2.7
OL-29505-01
11
System Requirements
Table 3
Supported Phones (continued)
Supported Phones
Supported Expansion
Modules
Supported
Conference Stations
8941
—
—
—
—
—
—
8945
8961
9951
9971
ATA
CIPC – Cisco IP Communicator
Supported Modules and Cards
Table 4 lists the network modules and interface cards that Cisco Configuration Professional supports.
Table 4
Supported Modules and Cards
Modules and Cards
Advanced Integration
AIM-CUE
AIM2-CUE-K9
AIM-IPS-K9
AIM2-APPRE-104-K9
AIM-VPN/BP II PLUS
AIM-VPN/EP II PLUS
AIM-VPN/HP II PLUS
AIM-VPN/SSL-1
AIM-VPN/SSL-2
AIM-VPN/SSL-3
Analog Dialup
WIC-1AM
WIC-2AM
Analog and Digital Voice/Fax
Release Notes for Cisco Configuration Professional 2.7
12
OL-29505-01
System Requirements
Table 4
Supported Modules and Cards
Modules and Cards
NM-HD-1V
NM-HD-2V
NM-HD-2VE
NM-HDA-4FXS
NM-HDV2
NM-HDV2-1T1/E1
NM-HDV2-2T1/E1
EVM-HD-8FXS/DID
EM-HDA-8FXS
EM-HDA-4FXO
EM-HDA-6FXO
EM-HDA-3FXS/4FXO
EM-4BRI-NT/TE
EM2-HDA-4FXO
EM3-HDA-8FXS/DID
Application
ISM-SRE-300-K9
SM-SRE-700-K9
SM-SRE-900-K9
NME-WAE-302-K9
NME-WAE-502-K9
NME-WAE-522-K9
NME-APPRE -302-K9
NME-APPRE -502-K9
NME-APPRE -522-K9
Broadband
Release Notes for Cisco Configuration Professional 2.7
OL-29505-01
13
System Requirements
Table 4
Supported Modules and Cards
Modules and Cards
EHWIC-VA-DSL-A
EHWIC-VA-DSL-B
EHWIC-VA-DSL-M
EHWIC-4SHDSL-EA
EHWIC-1GE-SFP-CU
HWIC-1ADSL
HWIC-1ADSLI
HWIC-1ADSL-M
HWIC-1CABLE-D-2
HWIC-1CABLE-E/J-2
HWIC-1GE-SFP
HWIC-1VDSL
HWIC-2SHDSL
HWIC-4SHDSL
HWIC-4SHDSL-E
HWIC-ADSL-B/ST
HWIC-ADSLI-B/ST
WIC-1SHDSL-V2
WIC-1SHDSL-V3
WIC-1ADSL
WIC 1ADSL-DG
WIC 1ADSL-I-DG
Cisco Unity Voicemail
NME-CUE
NM-CUE
NM-CUE-EC
Ethernet Routed Port
HWIC-1FE
HWIC-2FE
Ethernet Switch
Release Notes for Cisco Configuration Professional 2.7
14
OL-29505-01
System Requirements
Table 4
Supported Modules and Cards
Modules and Cards
NM-16ESW
NM-16ESW-PWR
NM-16ESW-1GIG
NM-16ESW-PWR-1GIG
NMD-36ESW-PWR
NMD-36ESW-PWR-2GIG
NME-16ES-1G-P
NME-X-23ES-1G-P
NME-XD-24ES-1S-P
NME-XD-48ES-2S-P
SM-32A
SM-ES2-16-P
SM-ES2-24
SM-ES2-24-P
SM-D-ES2-48
SM-ES3-16-P
SM-ES3-24-P
SM-ES3G-16-P
SM-ES3G-24-P
SM-D-ES3-48-P
SM-D-ES3G-48-P
EHWIC-4ESG
EHWIC-4ESG-P
EHWIC-D-8ESG
EHWIC-D-8ESG-P
HWIC-4ESW
HWIC-4ESW-POE
HWIC-D-9ESW
HWIC-D-9ESW-POE
ISDN BRI
WIC-1B-S/T-V3
Multiflex Trunk Voice & WAN Interface Cards
VWIC2-1MFT-T1/E1
VWIC2-2MFT-T1/E1
Serial Sync/Async Interface
Release Notes for Cisco Configuration Professional 2.7
OL-29505-01
15
System Requirements
Table 4
Supported Modules and Cards
Modules and Cards
HWIC-16A
HWIC-2A/S
HWIC-4A/S
HWIC-8A
HWIC-8A/S-232
WIC-2A/S
Serial WAN Interface
HWIC-1T
HWIC-2T
HWIC-4T
HWIC-1DSU-T1
WIC-1T
WIC-2T
WIC-1DSU-T1-V2
WIC-1DSU-56K4
Voice Interface
VIC-2DID
VIC-4FXS/DID
VIC2-2FXO
VIC2-4FXO
VIC2-2FXS
VIC2-2BRI-NT/TE
VIC2-2E/M
VIC3-4FXS/DID
VIC3-2FXS/DID
VIC3-2FXS-EDID
VPN and Security
NME-IPS-K9
NME-NAC-K9
Wireless AP
Release Notes for Cisco Configuration Professional 2.7
16
OL-29505-01
System Requirements
Table 4
Supported Modules and Cards
Modules and Cards
HWIC-AP-G-A
HWIC-AP-G-E
HWIC-AP-G-J
HWIC-AP-AG-A
HWIC-AP-AG-E
HWIC-AP-AG-J
Wireless WAN
EHWIC-3G-EVDO-B
EHWIC-3G-EVDO-S
EHWIC-3G-EVDO-V
EHWIC-3G-HSPA+7
EHWIC-3G-HSPA-U
HWIC-3G-CDMA-S
HWIC-3G-CDMA-V
HWIC-3G-HSPA
HWIC-3G-HSPA-A
HWIC-3G-HSPA-G
HWIC-3G-GSM
PCEX-3G-CDMA-V
PCEX-3G-HSPA
PCEX-3G-HSPA-G
PCEX-3G-HSPA-R6
PCEX-3G-HSPA-US
Connected Grid Router
GRWIC-D-ES-6S
GRWIC-D-ES-2S-8PC
Connected Grid
Table 5 lists the connected grid devices that Cisco Configuration Professional supports.
Table 5
Connected Grid
Switches
Routers
CGS-2520-24TC
CGS-2520-16S-8PC
CGR 2010/K9
Release Notes for Cisco Configuration Professional 2.7
OL-29505-01
17
System Requirements
Cisco IOS Releases
Cisco Configuration Professional is compatible with the Cisco IOS releases listed in Table 6.
Table 6
Cisco Configuration Professional-Supported Routers and Cisco IOS Versions
Router Model
Minimum Cisco Configuration Professional-Supported
Cisco IOS Versions
Cisco 815
12.4(11)T
Cisco 850 series
12.4(9)T
Cisco 861
12.4(20)T
Cisco 867
15.0(1)M
Cisco 870 series
12.4(9)T
Cisco 881
12.4(20)T
Cisco 886
15.0(1)M
Cisco 887
15.0(1)M
Cisco 888
12.4(20)T
Cisco 890 series
15.0(1)M
Cisco 1801
Cisco 1802
Cisco 1803
12.4(9)T
Cisco 1805
12.4(15)XY
Cisco 1811
Cisco 1812
12.4(9)T
Cisco 1841
12.4(9)T
Cisco 1861
12.4(20)T
Cisco 1941
15.0(1)M
Cisco 1941W
Cisco 2800 series
12.4(9)T
Cisco 2900 series
15.0(1)M
Cisco 3800 series
12.4(9)T
Cisco 3900 series
15.0(1)M
Determining the Cisco IOS Release
To determine the release of the Cisco IOS software currently running on your Cisco router, log into the
router and enter the show version EXEC command. The following sample output from the show version
command indicates the Cisco IOS release on the second output line:
Router> show version
Cisco IOS Software, C2951 Software (C2951-UNIVERSALK9-M), Version 15.1(2)T1"
Release Notes for Cisco Configuration Professional 2.7
18
OL-29505-01
System Requirements
Required IP Address Configuration Information
Table 7 provides the required IP address configuration for the PC. Use this information to complete the
“Task 4: Configure the IP Address On the PC” section in the Cisco Configuration Professional Quick
Start Guide.
Table 7
Required PC IP Address Configurations
Router Model
DHCP Server
Required PC IP Address Configuration
Cisco 815, Cisco 85x, Cisco 86x, Cisco
87x, Cisco 88x, Cisco 89x, Cisco 180x,
Cisco 1805, Cisco 1811 and 1812
Yes
Obtains the IP address automatically
Cisco 1841, Cisco 1861, Cisco 28xx,
Cisco 38xx, Cisco 29xx, Cisco 39xx
No
Static IP address from 10.10.10.2 to
10.10.10.6
Subnet Mask: 255.255.255.248
Router Configuration Requirements
To run Cisco Configuration Professional, a router configuration must meet the requirements shown in
Table 8.
Table 8
Router Configuration Requirements
Feature
Requirement
Configuration Example
Secure access
SSH and HTTPS
Router(config)# ip http secure-server
Router(config)# ip http authentication local
Router(config)# line vty 0 15
Router(config)# login local
Router(config-line)# transport input ssh
Router(config-line)# transport output ssh
Nonsecure access
Telnet and HTTP
Router(config)# ip http server
Router(config)# ip http authentication local
Router(config)# line vty 0 15
Router(config)# login local
Router(config-line)# transport input telnet
Router(config-line)# transport output telnet
User privilege level
15
Router(config)# username cisco privilege 15 secret 0 cisco
The default configuration file meets all Cisco Configuration Professional requirements. The default
configuration file has the name cpconfig-model_number.cfg. For example, the configuration file for the
Cisco 860 and Cisco 880 routers is named cpconfig-8xx.cfg.
Release Notes for Cisco Configuration Professional 2.7
OL-29505-01
19
New and Changed Information
Cisco Configuration Professional Ordering Options
Table 9 describes the ordering options under which Cisco Configuration Professional can be ordered.
Cisco Configuration Professional Express is a product that is shipped in the router flash memory when
the router is ordered with Cisco Configuration Professional.
Table 9
Cisco Configuration Professional Ordering Options
Ordering Options
Description
ISR-CCP-CD
Cisco Configuration Professional: Shipped on CD
Cisco Configuration Professional Express: Shipped in router flash
memory
SSL Client: Shipped in router flash memory
Default Configuration File: Shipped in router flash memory and in
NVRAM
ISR-CCP-CD-NOCONF
Cisco Configuration Professional: Shipped on CD
Cisco Configuration Professional Express: Shipped in router flash
memory
SSL Client: Shipped in router flash memory
Default Configuration File: Shipped in router flash memory
ISR-CCP-EXP
Cisco Configuration Professional: Not shipped
Cisco Configuration Professional Express: Shipped in router flash
memory
SSL Client: Shipped in router flash memory
Default Configuration File: Shipped in router flash memory and in
NVRAM
ISR-CCP-EXP-NOCONF
Cisco Configuration Professional: Not shipped
Cisco Configuration Professional Express: Shipped in router flash
memory
SSL Client: Shipped in router flash memory
Default Configuration File: Shipped in router flash memory
ISR-CCP-CD
Cisco Configuration Professional: Shipped on CD
Spare SKU: Mapped to ISR-CCP-CD
New and Changed Information
This section contains new information about Cisco Configuration Professional and any information that
has changed in Cisco Configuration Professional.
This section contains the following sections:
•
New and Changed Features, page 21
•
New Hardware Support, page 21
Release Notes for Cisco Configuration Professional 2.7
20
OL-29505-01
New and Changed Information
New and Changed Features
The following new features are introduced in Cisco Configuration Professional 2.7 release:
•
Support for configuring 4G Cellular Interface
•
Smart Call-Home
For more information, refer to the screencasts at
http://www.cisco.com/en/US/docs/net_mgmt/cisco_configuration_professional/scrcst/ccpsc.html
New Hardware Support
The new devices supported are:
•
C819G+7-M-K9
•
C819G-U-M-K9
•
C819G-V-M-K9
•
C819G-S-M-K9
•
C819G-B-M-K9
•
C819HG+7-M-K9
•
C819HG-U-M-K9
•
C819HG-V-M-K9
•
C819HG-S-M-K9
•
C819HG-B-M-K9
•
C819HGW+7-E-K9
•
C819HGW+7-N-K9
•
C819HGW+7-A-A-K9
•
C819HGW-V-A-K9
•
C819HGW-S-A-K9
•
C819H-K9
•
C819HWD-E-K9
•
C819HWD-A-K9
•
C812G+7-K9
•
C812G-CIFI+7-E-K9
•
C812G-CIFI+7-N-K9
•
C812G-CIFI-V-A-K9
•
C812G-CIFI-S-A-K9
•
C819HG-4G-V-K9
•
C819HG-4G-A-K9
•
C819HG-4G-G-K9
•
C819G-4G-V-K9
Release Notes for Cisco Configuration Professional 2.7
OL-29505-01
21
New and Changed Information
•
C819G-4G-A-K9
•
C819G-4G-G-K9
•
C881G-4G-V-K9
•
C881G-4G-A-K9
•
C881G-4G-G-K9
•
C881G-MM-K9
•
C819HG-3G-MM-K9
•
C819G-3G-MM-K9
•
C892FSP-K9
•
C896VA-K9
•
C897VA-K9
•
C897VAW-A-K9
•
C897VAW-E-K9
•
C897VA-M-K9
•
C897VAW-M-E-K9
•
C898EA-K9
•
CISCO866VAE-W-E/K9
•
CISCO867VAE-W-E/K9
•
CISCO867VAE-W-A/K9
•
CGS-1000-4TS-G-B
•
CGS-1000-4T-G-B
•
CGS-1000-8TC-G-E
•
CGS-1000-16TC-G-E
•
CGS-1000-16TC-G-X
•
CGS-1000-16TC-GPE
•
C881WD-A-K9
•
C881WD-E-K9
•
C887VA-WD-A-K9
•
C887VA-WD-E-K9
•
C887VAGW+7-A-K9
•
C887VAGW+7-E-K9
•
Cisco1905/K9
•
EHWIC-4G-LTE-V
•
EHWIC-4G-LTE-G
•
EHWIC-4G-LTE-A
•
GRWIC-4G-LTE-V
•
EHWIC-1GEX-SFP-CU
•
GRWIC-2SHDSL
Release Notes for Cisco Configuration Professional 2.7
22
OL-29505-01
Limitations and Restrictions
•
GRWIC-VA-DSL-A
•
GRWIC-VA-DSL-B
•
GRWIC-VA-DSL-M
•
GRWIC-ISDN-1B-U
•
GRWIC-ISDN-1B-S/T
•
VWIC3-1MFT-T1/E1
•
VWIC3-2MFT-T1/E1
•
VWIC3-4MFT-T1/E1
Limitations and Restrictions
This section describes restrictions and limitations that may apply to Cisco Configuration Professional.
It contains the following sections:
•
Cisco Configuration Professional Minimum Screen Resolution, page 23
•
JRE Settings for Cisco Configuration Professional, page 23
•
Pop-up Screens Appearing on Primary Monitor if Cisco Configuration Professional Is Moved to
Extended Monitor, page 24
Cisco Configuration Professional Minimum Screen Resolution
Cisco Configuration Professional requires a screen resolution of at least 1024 x 768.
JRE Settings for Cisco Configuration Professional
The following JRE settings are needed for Cisco Configuration Professional to function properly:
Step 1
Go to Start > Control Panel > Java.
Step 2
Click View under Java Applet Runtime Settings.
Step 3
Select your JRE in use.
Step 4
Set the "Java runtime parameters" with the value "-Xmx256m -Dsun.java2d.d3d=false".
In addition, if JRE is upgraded to versions 1.6.0_11 or above, following settings are needed after Cisco
Configuration Professional installation.
Step 1
Go to Start > Control Panel > Java > Advance.
Step 2
Select "Java Plug-in" tree.
Step 3
Uncheck the check box for Enable next-generation Java Plug-in.
Step 4
Restart Cisco Configuration Professional.
Release Notes for Cisco Configuration Professional 2.7
OL-29505-01
23
Important Notes
Pop-up Screens Appearing on Primary Monitor if Cisco Configuration
Professional Is Moved to Extended Monitor
If Cisco Configuration Professional is running on a laptop that is also connected to an external monitor,
and the screen is set for extended display, pop-up dialog boxes of all SDM applet security pages, routing
pages, and help pages appear on the primary monitor. This issue is seen in the following scenario:
Step 1
Connect the monitor to a laptop and set the screen for extended display.
Step 2
Launch Cisco Configuration Professional and move it to secondary screen.
Step 3
Click Configure > Security > Security Audit > Perform Security Audit.
The Audit screen appears in the primary monitor and Cisco Configuration Professional in the secondary
monitor.
Important Notes
This section contains important information for Cisco Configuration Professional. It contains the
following sections:
•
Cisco IOS Enforces One-Time Use of Default Credentials, page 24
•
Cisco Configuration Professional Merge and Replace Configuration Functions Fail Under Some
Conditions, page 26
•
Cisco Configuration Professional May Lose Connection to Network Access Device, page 26
•
Popup Blockers Disable Cisco Configuration Professional Online Help, page 27
•
Screencasts for Cisco Configuration Professional Features, page 27
•
Temporary Internet Files—Impact on Launch, page 27
Cisco IOS Enforces One-Time Use of Default Credentials
To address CSCsm25466, Cisco IOS images included with recent shipments of Cisco 800, Cisco 1800,
Cisco 2800, Cisco 2900, Cisco 3800, and Cisco 3900 routers, enforce the one-time use of the default
user name and password provided in the Cisco Configuration Professional configuration file. If you
bypass Cisco Configuration Professional or Cisco Configuration Professional Express and use a console
or Telnet connection to log in to the router, the login and exec banners warn you that you must change
the username to “cisco” and the password to “cisco” before you log off the router. If you do not change
the credentials as directed, you will not be able to log in to the router the next time that you attempt to
do so.
The following Cisco IOS releases enforce the one-time use of the default credentials:
•
12.4(11)T or later
•
12.4(11)SW, 12.4(11)SW1, 12.4(11)XV, 12.4(11)XJ
•
12.4(9)T5, 12.4(9)T6
•
15.0(1)M or later
Release Notes for Cisco Configuration Professional 2.7
24
OL-29505-01
Important Notes
Follow the procedure in this section to secure the router by creating a new username and password, to
remove the login banner and exec banner warnings, and to save the configuration changes to the router
startup configuration.
Note
If you log in to the router using a Telnet or a console connection but do not complete the steps in this
procedure, be aware of the following:
•
If you do not change the default username and password, and then log off the router, you will not be
able to log in to the router again without entering the reload command. No additional warning is
given before you log off.
•
If you do not change the default username and password, but do enter the write memory command
before ending the session, future logins will be disabled. In this case, you will need to follow the
password recovery procedure at the following link:
http://www.cisco.com/en/US/products/sw/iosswrel/ps1831/products_tech_note09186a00801746e6
.shtml
To secure the router, remove the banner warnings and save the changes to the router startup config,
complete the following steps:
Step 1
Connect the blue console port on your router to a serial port on your PC using the light blue console
cable, included with your router. Refer to your router’s hardware installation guide for instructions.
Step 2
Connect the power supply to your router, plug the power supply into a power outlet, and turn on your
router. Refer to your router’s quick start guide for instructions.
Step 3
Use HyperTerminal or a similar terminal emulation program on your PC, with the terminal emulation
settings of 9600 baud, 8 data bits, no parity, 1 stop bit, and no flow control, to connect to your router.
Step 4
When prompted, enter the username cisco, and password cisco.
Step 5
Enter configuration mode by entering the following command:
yourname# configure terminal
Create a new username and password by entering the following command:
yourname(config)# username username privilege 15 secret 0 password
Replace username and password with the username and password that you want to use.
Step 6
Remove the default username and password by entering the following command:
yourname(config)# no username cisco
Step 7
To remove the login banner, enter the following command:
yourname(config)# no banner login
The login banner warning will no longer appear.
Step 8
To remove the exec banner, enter the following command:
yourname(config)# no banner exec
The exec banner warning will no longer appear.
Step 9
Leave configuration mode, by entering the following command:
yourname(config)# end
Release Notes for Cisco Configuration Professional 2.7
OL-29505-01
25
Important Notes
Step 10
Copy the configuration changes to the startup configuration by entering the following command:
yourname# copy running-config startup-config
When logging in to the router in the future, use the username and password that you created in Step 6.
Cisco Configuration Professional Merge and Replace Configuration Functions
Fail Under Some Conditions
The problem described here is caveat CSCsj21989. If you attempt to merge configuration changes made
using the Cisco Configuration Professional Config Editor feature, or replace the running configuration
with a configuration from the Config Editor, the router configuration will not be changed if there is a
network device with a Network Address Translation (NAT) IP address, or a cache engine in the
connection between the PC and the router. If you need to make changes to the router configuration that
you would normally make using the Cisco Configuration Professional Config Editor, use the Cisco IOS
CLI instead. Cisco Configuration Professional Security Dashboard may display threats unrelated to your
Cisco IOS IPS installation
Some (or all) of the top threats you obtain using the Cisco Configuration Professional Security
Dashboard may not pertain to your Cisco IOS IPS installation. After you deploy the signatures
applicable to the top threats displayed by the Cisco Configuration Professional Security Dashboard, the
dashboard may still display some (or all) top threats with a red icon because applicable signatures are
not found. Those remaining top threats are unrelated to your Cisco IOS IPS installation and are not a
danger to your router running Cisco IOS software.
Cisco Configuration Professional May Lose Connection to Network Access
Device
This note concerns the Network Admission Control (NAC) feature.
If the PC used to invoke Cisco Configuration Professional returns a posture state (Healthy, Infected,
Checkup, Quarantine, or Unknown) and if the group policy on the ACS server attached to the posture
token assigned to the PC has a redirect URL configured, the connection between Cisco Configuration
Professional and the router acting as the Network Access Device (NAD) may be lost. The same problem
can occur if an exception list entry attached to a policy with a redirect URL is configured with the IP
address or MAC address of the PC.
If you try to reinvoke Cisco Configuration Professional from this type of PC, you will not be able to do
so because the browser will be redirected to the location specified in the redirect URL.
There are two workarounds for this problem:
•
Ensure that the PC that you use to invoke Cisco Configuration Professional attains a posture token
that has an associated group policy on the ACS server that is not configured with a redirect URL.
•
Alternatively, use Cisco Configuration Professional to create a NAC exception list entry with the IP
address or MAC address of the PC you use to invoke Cisco Configuration Professional. Note that
the exception list entry created for the PC should be associated to an exception policy that does not
have a redirect URL configured in it.
For more information, see the links on the Cisco Configuration Professional NAC online help pages.
Release Notes for Cisco Configuration Professional 2.7
26
OL-29505-01
Caveats
Popup Blockers Disable Cisco Configuration Professional Online Help
If you have enabled popup blockers in the browser you use to run Cisco Configuration Professional,
online help will not appear when you click the help button. To prevent this from happening, you must
disable the popup blocker when you run Cisco Configuration Professional. Popup blockers may be
enabled in search engine toolbars, or may be standalone applications integrated with the web browser.
Microsoft Windows XP with Service Pack 2 blocks popups by default. To turn off popup blocking in
Internet Explorer, go to Tools > Pop-up Blocker > Turn Off Pop-up Blocker.
If you have not installed and enabled third-party pop up blockers, go to Tools > Internet Options >
Privacy, and uncheck the Block popups checkbox.
Screencasts for Cisco Configuration Professional Features
Instead of online help, screencasts have been provided for the Cisco Configuration Professional 2.7
features:
These screencasts are located at:
http://www.cisco.com/en/US/docs/net_mgmt/cisco_configuration_professional/scrcst/ccpsc.html
You must have Internet access to view the screencasts.
Temporary Internet Files—Impact on Launch
Because of Microsoft Windows Java caching issues, Cisco Configuration Professional is sometimes
unable to complete discovery of a device. To fix this issue, complete the following steps:
Step 1
Choose Application > Exit to shut down Cisco Configuration Professional.
Step 2
Close all existing Internet Explorer windows.
Step 3
Go to Start > Control Panel > Java. The General tab is displayed.
Step 4
In the Temporary Internet Files box, click Delete Files.
Step 5
In the displayed dialog, leave all file types checked, and click OK.
Step 6
Click OK in the Java control panel to close it.
Step 7
Restart Cisco Configuration Professional.
Caveats
Caveats describe unexpected behavior in Cisco Configuration Professional. This section contains the
following:
•
Resolved Caveats, page 28
•
Open Caveats, page 28
Release Notes for Cisco Configuration Professional 2.7
OL-29505-01
27
Caveats
Resolved Caveats
Table 10 lists caveats that are resolved in Cisco Configuration Professional Version 2.7.
Table 10
Resolved Caveats in Cisco CP 2.7
Bug ID
Summary
CSCtu18162
Editing the non-persistent backup to persistent does not remove the cellular route
CSCto13265
Site-to-site VPN displays duplicate tunnel entry
CSCtn10781
Overlaid extensions do not follow the order you specified
Open Caveats
Table 11 lists caveats that are open in Cisco Configuration Professional Version 2.7.
Table 11
Open Caveats in Cisco CP 2.7
Bug ID
Summary
CSCue49702
Configured 3G cellular
interfaces are not displayed on Symptom Cisco Configuration Professional does not display the
the NAT page
configured 3G cellular interfaces on the NAT page.
Additional Information
Conditions This issue is encountered on devices with Wireless AP,
where 3G cellular feature is configured.
Workaround Rediscover the device.
CSCug01227
GetVPN key server
configuration details are not
reflected on the GUI after
successful configuration
The configuration details of the GetVPN key server are not
displayed on the GUI.
Symptom
Conditions This error is encountered on devices with IOS version 15.2
or higher, and IOS-XE version 15.3 or higher.
Workaround Rediscover the device.
CSCtw51884
The create/edit/delete action
fails on the GSM profile screen Symptom The Create, Edit or Delete action fails on the GSM profile
when the hostname has the +
screen and Cisco Configuration Professional displays this error
character.
message Error has occurred while configuring Cellular GSM modem
profile. However, Cisco Configuration Professional configures the
router successfully.
Conditions This problem is seen when the hostname of the router has
any illegal character. For example: !,@, #, $,%, ^, &, *, (), and +. For
example, C881GW+7 is not a valid hostname.
Workaround .Remove the illegal characters from the hostname and
rediscover the device.
Release Notes for Cisco Configuration Professional 2.7
28
OL-29505-01
Caveats
Table 11
Open Caveats in Cisco CP 2.7 (continued)
Bug ID
Summary
CSCtt45687
The VPN design guide does not
launch on the Google chrome Symptom The Cisco Configuration Professional does not display the
browser.
VPN design guide when you select Configure > Security > VPN >
VPN Design Guide.
Additional Information
Conditions This problem is seen when the Google chrome browser is set
as the default browser in the system.
Workaround Set Mozilla Firefox or Internet Explorer as the default
browser in your system.
CSCtw61469
Cannot configure the SIP trunk
on Cisco 892F router.
Symptom You cannot configure the SIP Trunk on a Cisco 892F-CUBE
ISR device. Resetting the Unified Communication mode to default and
changing the CUBE settings is not successful due to CLI error.
Conditions This problem occurs only when a Cisco 892F-CUBE ISR
device is configured with CUBE feature. Cisco Configuration
Professional does not allow you to configure or unconfigure the SIP
trunk on the device.
The following CLIs cannot be configured or unconfigured on the
device:
•
call threshold global cpu-avg low 68 high 75
•
no call threshold global cpu-avg low 68 high 75
•
call threshold global total-mem low 75 high 85
•
no call threshold global total-mem low 75 high 85
Workaround Configure the SIP Trunk manually or follow these steps.
1.
Discover the Cisco 892F-CUBE ISR with Unified
Communication mode as CUBE.
2.
Navigate to SIP Trunks.
3.
Select the service provider and provide inputs for the available
parameters.
4.
Save the generated CLI preview in a text file.
5.
Use the Config Editor to upload the file after removing the
above mentioned CLIs and apply the config.
Release Notes for Cisco Configuration Professional 2.7
OL-29505-01
29
Caveats
Table 11
Open Caveats in Cisco CP 2.7 (continued)
Bug ID
Summary
Additional Information
CSCtu13147
IPS Auto update screen does
not display the complete
configured information.
Symptom Configure the IPS Auto Update settings using the Local
Server option. Rediscover the device, part of the configured
information related to recurring update schedule is missing from the
Edit IPS > Auto Update > Local Server screen.
Conditions This problem is seen when you configure the IPS Auto
Update settings using the Local Server option and configure the Update
Schedule by selecting the Setup Recurring Update checkbox. The IPS
Auto Update screen does not display the complete configured
information when you rediscover the device and navigate to IPS Auto
Update screen.
Workaround There is no workaround.
CSCto88259
GenericJDBCException seen
while launching Cisco
Configuration Professional.
Symptom The following error is seen when Cisco Configuration
Professional is launched:
org.hibernate.exception.GenericJDBCException: Cannot open
connection
Conditions This problem rarely occurs and there are no specific steps
which create the problem. Database corruption is a possibility.
Workaround Reinstall Cisco Configuration Professional.
CSCto70309
Unified Communications mode
is displayed as CUBE when the Symptom On an ISR-G2, if the mode border-element command is not
mode border-element
configured under voice service voip and if telephony service and
command is not configured.
max-dn commands are configured, Cisco Configuration Professional
displays the Unified Communications feature as CUBE.
Conditions This problem occurs only on an ISR-G2 if the mode
border-element is not configured and if max-dn is configured under
the telephony-service command.
Workaround Select the appropriate mode in the Unified
Communications Features screen and deliver the CLI.
CSCto07804
Traffic Monitoring Netflow
Services fails to start in some
scenarios.
Symptom Data Collector Service fails to start as a result of which data
is not collected from the router.
Conditions This can happen if files are not copied properly or get
corrupted while installing the Data Collector Service.
Workaround Reinstall the Data Collector Service.
Release Notes for Cisco Configuration Professional 2.7
30
OL-29505-01
Caveats
Table 11
Open Caveats in Cisco CP 2.7 (continued)
Bug ID
Summary
CSCto73606
Traffic Monitoring: Cisco
Configuration Professional
displays error when you click
Start Monitoring or Stop
Monitoring on any interface
while Data Collector Services
are not running.
Additional Information
Symptom Cisco Configuration Professional displays a pop-up with
Java.lang.NullPointerException error when you try to stop monitoring
by clicking the Stop Monitoring link, while the Interface Collector
Service is not running.
Conditions Cisco Configuration Professional displays error when you
try to stop monitoring by clicking the Stop Monitoring link, while the
Interface Collector Service is not running.
Workaround Start the Interface Collector Service and then stop
monitoring.
CSCto76962
Traffic Monitoring: Cisco
Configuration Professional
displays value as 0 when
interface is not being
monitored.
Symptom Cisco Configuration Professional displays the value as zero
(0) if an interface is not being monitored for some time.
Conditions If you monitor traffic on an interface for some time, stop and
then start monitoring traffic again, Cisco Configuration Professional
displays a value of zero for the time interval that you were not
monitoring the interface.
Workaround There is no workaround.
Release Notes for Cisco Configuration Professional 2.7
OL-29505-01
31
Caveats
Table 11
Open Caveats in Cisco CP 2.7 (continued)
Bug ID
Summary
Additional Information
CSCto83180
Multiple virtual machines
(VMs) installed on SRE-V are
not displayed.
Symptom
•
Case 1—If you did not select a virtual machine in Configure >
Interface Management > Module Configuration > SRE-V >
Permissions > User/Group > Edit, Select is displayed.
•
Case 2—Adding one more virtual machine using Configure >
Interface Management > Module Configuration > SRE-V >
Permissions > User/Group > Edit removes the previously added
virtual machine configuration.
•
Case 3—Multiple entries are shown in the SRE-V Permissions
screen for each user/group.
Conditions
•
Case 1—In Configure > Interface Management > Module
Configuration > SRE-V > Permissions > User/Group > Edit,
when you do not select a virtual machine from the drop-down
menu, Select is displayed.
•
Case 2—When the user/group already has one virtual machine
associated with it, adding one more virtual machine using
Configure > Interface Management > Module Configuration >
SRE-V > Permissions > User/Group > Edit can remove the
previously added virtual machine configuration.
•
Case 3—When a virtual machine, for example VM1 is already
added to the user/group, adding one more virtual machine may
create multiple entries in the Permissions summary screen upon
refreshing the page.
Workaround
•
Case 1—There is no workaround. Assume that the default virtual
machine Host is associated to the user/group when Select is
displayed.
•
Case 2—To add multiple virtual machines to the user/group, use
the CLI.
•
Case 3—Read each entry as corresponding to one instance of
virtual machine associated with the user/group.
Release Notes for Cisco Configuration Professional 2.7
32
OL-29505-01
Caveats
Table 11
Open Caveats in Cisco CP 2.7 (continued)
Bug ID
Summary
CSCto85895
GRWIC-D-ES-2S-8PC/-6S 802.1x moving to high-security Symptom When you click Finish in the 802.1x wizard for
mode directly fails.
GRWIC-D-ES-2S-8PC or GRWIC-D-ES-6S with high-security or
low-impact as the mode an error Configuration failed radius-server vsa
send is seen.
Additional Information
Conditions This issue is seen when you click Finish in the 802.1x
wizard for GRWIC-D-ES-2S-8PC or GRWIC-D-ES-6S with
high-security mode or low-impact mode. The issue is not seen in the
monitor mode.
Workaround Configure AAA details using monitor mode and then
change to low-impact mode or high-security mode.
Release Notes for Cisco Configuration Professional 2.7
OL-29505-01
33
Caveats
Table 11
Open Caveats in Cisco CP 2.7 (continued)
Bug ID
Summary
Additional Information
CSCth67558
Unable to discover switching
module.
Symptom Cisco Configuration Professional fails to discover switching
module and reports that the module is being reloaded in the discovery
details.
Conditions When the switching module is configured with login local or
AAA new-model configuration or both, the module requires one more
level of authentication along with the usual authentication. In this case,
you need to provide the username and password twice to get into the
module prompt.
Workaround Remove the login local and AAA new-model configuration
so that the extra level of authentication is not required.
CSCth34158
Switching Modules folder is
not listed in the left navigation Symptom Switching Modules folder is not listed in the left navigation
pane.
pane even when the device has supported switch modules that are
managed by Cisco Configuration Professional.
Conditions
•
Multiple levels (more than one level) of authentication is required
for accessing the switch module console.
•
Enabled password is configured on the device.
•
AAA is configured on both the router and the switch modules.
•
Privilege level 15 is not configured under line con 0.
Workaround
•
Ensure that the router and switch have the same username
(privilege level 15) and a password is configured when switch
console requires authentication.
•
If there is no login configured for line con 0, ensure privilege level
15 is configured under line con 0.
•
If AAA is configured on the router, make sure that no
authentication is required for the switch module and privilege level
15 is configured under line con 0.
Release Notes for Cisco Configuration Professional 2.7
34
OL-29505-01
Related Documentation
Related Documentation
Table 12 describes the related documentation available for Cisco Configuration Professional.
Table 12
Cisco Configuration Professional Documentation
Document Title
Available Formats
Readme First for
Cisco Configuration Professional
This document is available at the following locations:
Cisco Configuration Professional
Quick Start Guide
Cisco Configuration Professional
Getting Started Guide
•
http://www.cisco.com/
•
Product CD-ROM in the Documentation folder
This guide is available at the following locations:
•
http://www.cisco.com/
•
Product CD-ROM in the Documentation folder
This guide is available at the following locations:
•
http://www.cisco.com/
•
Product CD-ROM in the Documentation folder
Note
Cisco Configuration Professional
User Guide
Cisco Configuration Professional
Express User Guide
Note
During the installation process, just before you have
finished installing the product, you are provided the
option to read the Getting Started guide.
This guide is available at the following locations:
•
http://www.cisco.com/
•
Online help
This guide is available at the following locations:
•
http://www.cisco.com/
•
Online help
Release Notes for
Cisco Configuration Professional
This document is available at the following location:
Release Notes for
Cisco Configuration Professional
Express
This document is available at the following location:
•
•
http://www.cisco.com/
http://www.cisco.com/
For information on obtaining documentation and technical assistance, product security, and additional
information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and
revised Cisco technical documentation, at
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html.
Release Notes for Cisco Configuration Professional 2.7
OL-29505-01
35
Glossary
Glossary
ACEs—Access List Elements
ACLs—Access Control Lists
B-ACD—Basic Automatic Call Distribution
CUBE—Cisco Unified Border Element
HWIC—High-Speed WAN Interface Card
HSPA—High-Speed Packet Access
HSPA—A—High-Speed Packet Access for Americas
HSPA—G—High-Speed Packet Access for Global
PCEX—PC Express
PPP—Point-to-Point Protocol (PPP) PDP type
This document is to be used in conjunction with the documents listed in the “Related Documentation” section.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of
Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The
use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any
examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only.
Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.
© 2013 Cisco Systems, Inc. All rights reserved.
Printed in the USA on recycled paper containing 10% postconsumer waste.
Release Notes for Cisco Configuration Professional 2.7
36
OL-29505-01