Ariens 921003 - ST1130DLE Specifications

Sno-Thro®
Owner/Operator Manual
Models
921001 – ST824E
921002 – ST1027LE
921003 – ST1130DLE
921004 – ST924DLE
ENGLISH
FRANÇAIS
00660400A 10/07
Printed in USA
TABLE OF CONTENTS
SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . 4
STORAGE . . . . . . . . . . . . . . . . . . . . . . 35
ASSEMBLY. . . . . . . . . . . . . . . . . . . . . . . 8
SERVICE PARTS . . . . . . . . . . . . . . . . . 35
CONTROLS and FEATURES. . . . . . . . 13
ACCESSORIES . . . . . . . . . . . . . . . . . . 35
OPERATION . . . . . . . . . . . . . . . . . . . . . 15
TROUBLESHOOTING . . . . . . . . . . . . . 36
MAINTENANCE . . . . . . . . . . . . . . . . . . 21
SPECIFICATIONS . . . . . . . . . . . . . . . . 37
SERVICE AND ADJUSTMENTS . . . . . 24
WARRANTY . . . . . . . . . . . . . . . . . . . . . 38
INTRODUCTION
NON-ENGLISH MANUALS
Manuals
Manuals in languages other than
English may be obtained from your
Dealer. Visit your dealer or
www.ariens.com for a list of
languages available for your
equipment.
Manuals printed in languages other
than English are also available as a
free download on our website:
http://www.ariens.com
Manuales en idiomas diferentes
del ingles
Before operation of unit, carefully and
completely read your manuals. If used
improperly, this unit could be dangerous and
cause personal injury or property damage.
The contents will provide you with safety
instructions for the safe use of your unit
during normal operation and maintenance.
All reference to left, right, front, or rear are
given from operator standing in operation
position and facing the direction of forward
travel.
Engine Manual
Puede obtener manuales en
idiomas diferentes del inglés en su
distribuidor. Visite a su distribuidor
o vaya a www.ariens.com para
obtener una lista de idiomas
disponibles para su equipo.
También puede imprimir manuales
en idiomas diferentes del inglés
descargándolos gratuitamente de
nuestra página Web:
http://www.ariens.com
Manuels non anglais
Des manuels dans différentes
langues sont disponibles chez
votre revendeur. Rendez-vous
chez votre revendeur ou allez sur
le site www.ariens.com pour
consulter la liste des langues
disponibles pour votre équipement.
Les manuels imprimés dans des
langues différentes de l’anglais
sont également disponibles en
téléchargement gratuit sur notre
site Web :
The engine on this unit is covered by a
separate manual specific to the engine. This
manual is included in the literature package
that shipped with the unit. Refer to this
manual for engine service recommendations.
If the engine manual is not available, contact
the engine manufacturer for a replacement
manual.
Model and serial Numbers
When ordering replacement parts or making
service inquiries, know the Model and Serial
numbers of your unit and engine.
Numbers are located on the product
registration form in the unit literature
package. They are printed on a serial number
label, located on the frame of your unit.
http://www.ariens.com
GB - 2
Disclaimer
Ariens reserves the right to discontinue,
make changes to, and add improvements
upon its products at any time without public
notice or obligation. The descriptions and
specifications contained in this manual were
in effect at printing. Equipment described
within this manual may be optional. Some
illustrations may not be applicable to your
unit.
Delivery
Customer Note: If you have purchased this
product without complete assembly and
instruction by your retailer, it is your
responsibility to:
1. Read and understand all assembly
instructions in this manual. If you do not
understand or have difficulty following
the instructions, contact your nearest
Ariens Dealer for assistance. Make sure
all assembly has been properly
completed.
NOTE: To locate your nearest Ariens Dealer,
go to www.ariens.com on the Internet.
OS7006
Serial Number Label
Figure 1
• Record Unit Model and Serial numbers
here.
• Record Engine Model and Serial
number here.
WARNING: Improper assembly or
adjustments can cause serious
injury.
Product Registration
The Ariens dealer must register the product
at the time of purchase. Registering the
product will help the company process
warranty claims or contact you with the latest
service information. All claims meeting
requirements during the limited warranty
period will be honored, whether or not the
product registration card is returned. Keep a
proof of purchase if you do not register your
unit.
Customer Note: If the dealer does not
register your product, please fill out, sign, and
return the product registration card to Ariens
or go to www.ariens.com.
Unauthorized Replacement Parts
Use only Ariens replacement parts. The
replacement of any part on this vehicle with
anything other than an Ariens authorized
replacement part may adversely affect the
performance, durability, or safety of this unit
and may void the warranty. Ariens disclaims
liability for any claims or damages, whether
warranty, property damage, personal injury or
death arising out of the use of unauthorized
replacement parts. To locate your nearest
Ariens Dealer, go to www.ariens.com on the
internet.
GB - 3
2. Understand all Safety Precautions
provided in the manuals.
3. Review control functions and operation
of the unit. Do not operate the Sno-Thro
unless all controls function as described
in this manual.
4. Review recommended lubrication,
maintenance and adjustments.
5. Review Limited Warranty Policy.
6. Fill out a Product Registration Card and
return the card to the Ariens Company or
go to www.ariens.com.
SAFETY
Practices and Laws
WARNING: To avoid injury to
hands and feet, always disengage
clutches, shut off engine, and wait
for all movement to stop before
unclogging or working on snow
thrower.
Hand contact with the rotating
impeller is the most common cause
of injury associated with snow
throwers. Never use your hand to
clean out the discharge chute.
Keep hands and feet away from
auger and impeller.
Practice usual and customary safe working
precautions, for the benefit of yourself and
others. Understand and follow all safety
messages. Be alert to unsafe conditions and
the possibility of minor, moderate, or serious
injury or death. Learn applicable rules and
laws in your area. Always follow the practices
set forth in this manual.
Required Operator Training
Safety Alerts
Look for these symbols to point
out important safety
precautions. They mean:
Attention!
Original purchaser of this unit was instructed
by the seller on safe and proper operation. If
unit is to be used by someone other than
original purchaser; loaned, rented or sold,
ALWAYS provide this manual and any
needed safety training before operation.
Safety Decals and Locations
ALWAYS replace missing or damaged Safety
Decals. Refer to figures below for Safety
Decal locations.
Personal Safety Is
Involved!
921002, 003, 004
Become Alert!
Obey The Message!
2
1
The safety alert symbols above and signal
words below are used on decals and in this
manual. Read and understand all safety
messages.
08000134
3
DANGER: IMMINENTLY
HAZARDOUS SITUATION! If not
avoided, WILL RESULT in death or
serious injury.
WARNING: POTENTIALLY
HAZARDOUS SITUATION! If not
avoided, COULD RESULT in death
or serious injury.
Figure 2
CAUTION: POTENTIALLY
HAZARDOUS SITUATION! If not
avoided, MAY RESULT in minor or
moderate injury. It may also be
used to alert against unsafe
practices.
Notations
NOTE: General reference information for
proper operation and maintenance practices.
IMPORTANT: Specific procedures or
information required to prevent damage to
unit or attachment.
GB - 4
OS7016
ONLY use clean-out tool to
clear blockages. NEVER use
your hands.
921001
1
2. DANGER!
2
3
OS6610
OS7017
ROTATING PARTS! ONLY use
clean-out tool to clear
blockages. NEVER use your
hands. High speed impeller
rotates below discharge
opening. Wait for all moving
parts to stop before removing
clogs or servicing.
Figure 3
3. DANGER!
1. WARNING!
Read Owner/Operator Manual.
OS2080
OL1801
OL4370
Keep people away from unit
while operating. Keep children
out of work area and under
watchful care of a responsible
adult.
Never direct discharge towards
persons or property that may be
injured or damaged by thrown
objects.
ROTATING PARTS.
Keep clear of auger while
engine is running.
• Read Operator’s Manual.
• Allow operation only by
properly trained adult,
never children.
• Stop engine and remove
ignition key prior to leaving
the operator’s position for
any reason.
• Keep all controls, guards
and safety devices
properly serviced and
functional.
• Never direct discharge
towards persons or
property that may be
injured or damaged by
thrown objects.
OL0910
Safety Rules
Stop engine, remove key, read
manual before making any
repairs or adjustments.
OL4010
Wear appropriate hearing
protection.
OL4690
Read, understand, and follow all safety
practices in Owner/Operator Manual before
beginning assembly or operating. Failure to
follow instructions could result in personal
injury and/or damage to unit.
ALWAYS remove key and/or wire from spark
plug before assembly, maintenance or
service. Unintentional engine start up can
cause death or serious injury.
Complete a walk around inspection of unit
and work area to understand:
• Work area • Your unit • All safety decals
ALWAYS check overhead and side
clearances carefully before operation.
ALWAYS be aware of traffic when operating
along streets or curbs.
GB - 5
Keep children and people away. Keep
children out of work area and under watchful
care of a responsible adult.
NEVER allow children to operate or play on
or near unit. Be alert and shut off unit if
children enter area.
DO NOT allow adults to operate unit without
proper training. Only trained adults may
operate unit. Training includes actual
operation.
Keep area of operation clear of all toys, pets,
and debris. Thrown objects can cause injury.
Check for weak spots on docks, ramps or
floors. Avoid uneven work areas and rough
terrain. Stay alert for hidden hazards.
DO NOT operate near drop-offs, ditches, or
embankments. Unit can suddenly turn over if
a wheel is over the edge of a cliff or ditch, or if
an edge caves in.
Falling snow, fog, etc. can reduce vision and
cause an accident. Operate unit only when
there is good visibility and light.
NEVER operate unit after or during the use of
medication, drugs or alcohol. Safe operation
requires your complete and unimpaired
attention at all times.
NEVER allow anyone to operate this unit
when their alertness or coordination is
impaired.
DO NOT operate unit without wearing
adequate winter outer garments. Wear
adequate safety gear, including safety
glasses with side shields, and protective
gloves. Wear proper footwear to improve
footing on slippery surfaces.
DO NOT wear loose clothing or jewelry and
tie back hair that may get caught in rotating
parts.
Protect eyes, face and head from objects that
may be thrown from unit. Wear appropriate
hearing protection.
Avoid sharp edges. Sharp edges can cut.
Moving parts can cut off fingers or a hand.
ALWAYS keep hands and feet away from all
rotating parts during operation. Rotating parts
can cut off body parts.
NEVER place your hands or any part of your
body or clothing inside or near any moving
part while unit is running.
ALWAYS keep hands away from all pinch
points.
DO NOT touch unit parts which might be hot
from operation. Allow parts to cool before
attempting to maintain, adjust or service.
Never direct discharge towards persons or
property that may be injured or damaged by
thrown objects. Use extreme caution on
gravel surfaces. Stay alert for hidden hazards
or traffic. Adjust Runners so Scraper Blade
does not contact gravel.
DO NOT throw snow any higher than
necessary.
Deflected materials can cause injury and
property damage.
Always stand clear of the discharge area
when operating this unit.
Fumes from engine exhaust can cause injury
or death. DO NOT run engine in an enclosed
area. Always provide good ventilation.
ALWAYS disengage attachment, stop unit
and engine, remove key and allow moving
parts to stop before leaving operator’s
position.
ROTATING AUGER CAN CAUSE SERIOUS
INJURY. NEVER ATTEMPT TO UNCLOG
OR CLEAN UNIT WHILE ENGINE IS
RUNNING.
Read, understand, and follow all instructions
in the manual and on the machine before
starting.
Understand:
• How to operate all controls.
• The functions of all controls.
• How to STOP in an emergency.
Before starting engine, disengage control(s).
Use only approved extension cords and
receptacles when starting units equipped with
electric starter. DO NOT connect electric
starter cord to any wiring system that is not a
three-wire grounded system.
ALWAYS allow unit and engine to adjust to
outdoor temperatures before clearing snow.
DO NOT overload the machine capacity by
attempting to operate or to clear snow at too
fast a rate.
Slow down and turn corners slowly.
Do not operate in reverse unless absolutely
necessary. ALWAYS back up slowly. Always
look down and behind before and while
backing.
Disengage attachment drive when traveling
from one work area to another.
Abnormal Vibrations are a warning of trouble.
Striking a foreign object can damage unit.
Immediately stop unit and engine. Remove
key and wait for all moving parts to stop.
Remove wire from spark plug. Inspect unit
and make any necessary repairs before
restart.
GB - 6
Before cleaning, removing clogs or making
any inspections, repairs, etc.: disengage
clutch(es), stop unit and engine, remove key,
allow moving parts to stop. Allow hot parts to
cool.
Run unit a few minutes after clearing snow to
prevent freeze-up of attachment.
Disengage attachment when not in use.
Disengage all clutches before starting engine.
Adjust runners to clear gravel or crushed rock
surfaces safely.
Never leave a running unit unattended.
ALWAYS shut off engine before leaving unit.
ALWAYS remove key to prevent unauthorized
use.
Never carry passengers.
Check clutch and brake operation frequently.
Adjust and service as required. All motion of
drive wheels and auger/impeller must stop
quickly when control levers are released.
DO NOT operate on steep slopes. DO NOT
clear snow across the face of slopes. Keep all
movement on slopes slow and gradual. DO
NOT make sudden changes in speed or
direction. Use a slow speed to avoid stops or
shifts on slopes. Avoid starting or stopping on
a slope.
DO NOT park unit on a slope unless
absolutely necessary. When parking on a
slope always block the wheels.
ALWAYS shut off engine, remove key, and
close fuel shut-off valve or drain fuel when
transporting unit on a truck or trailer.
Use extra care when loading or unloading
unit onto trailer or truck.
Secure unit chassis to transport vehicle.
NEVER secure from rods or linkages that
could be damaged.
DO NOT transport machine while engine is
running.
Keep unit free of ice or other debris. Clean up
oil or fuel spills.
This product is equipped with an internal
combustion type engine. DO NOT use unit on
or near any unimproved, forest-covered or
brush covered land unless exhaust system is
equipped with a spark arrester meeting
applicable local, state or federal laws. A spark
arrester, if it is used, must be maintained in
effective working order by operator.
Fuel is highly flammable and its vapors are
explosive. Handle with care. Use an
approved fuel container.
NO smoking, NO sparks, NO flames.
ALWAYS allow engine to cool before
servicing.
NEVER fill fuel tank when engine is running
or hot from operation.
NEVER fill or drain fuel tank indoors.
Replace fuel cap securely and clean up
spilled fuel.
Never fill containers inside a vehicle or on a
truck or trailer bed with a plastic liner. Always
place containers on the ground away from
your vehicle before filling.
When practical, remove gas-powered
equipment from the truck or trailer and refuel
it on the ground. If this is not possible, then
refuel such equipment on a trailer with a
portable container, rather than from a
gasoline dispenser nozzle.
Keep the nozzle in contact with the rim of the
fuel tank or container opening at all times until
fueling is complete. Do not use a nozzle lockopen device.
If fuel is spilled on clothing, change clothing
immediately.
Before tipping unit up onto housing, remove
fuel so no spills will occur. Ensure unit is
secure and will not tip over during
maintenance.
ALWAYS keep protective structures, guards,
and panels in good repair, in place and
securely fastened. NEVER modify or remove
safety devices.
DO NOT change engine governor settings or
over-speed engine.
Fumes from engine exhaust can cause injury
or death. DO NOT run engine in an enclosed
area. Always provide good ventilation.
ALWAYS maintain unit in safe operating
condition. Damaged or worn out muffler can
cause fire or explosion.
Keep all hardware properly tightened. Check
shear bolts frequently.
Maintain or replace safety and instruction
labels, as necessary.
NEVER store unit with fuel in fuel tank, inside
a building where any ignition sources are
present such as hot water heaters, space
heaters, or clothes dryers. Allow the engine to
cool before storing in any enclosure.
Shut off fuel and allow engine to cool
completely before storing in closed area or
covering unit.
For extended storage, clean unit thoroughly.
See Engine Manual for proper storage.
Use only attachments or accessories
designed for your unit.
Check components frequently. If worn or
damaged, replace with manufacturer’s
recommended parts.
GB - 7
ASSEMBLY
921001
WARNING: AVOID INJURY. Read
and understand the entire Safety
section before proceeding.
3
WARNING: Dropping or tipping
over boxed unit could result in
personal injury or damage to unit.
2
1
Package Contents
921002, 003, 004
4
3
2
OS7021
1. Sno-Thro
Unit
2. Discharge
Chute
3. Chute Rod
1
4
4. Literature
Pack with
Extra Shear
Bolts
Figure 5
Assembly
OS7019
1. Sno-Thro
Unit
2. Discharge
Chute
3. Chute Rod
Tools Required:
• Pliers
• Open-End Wrenches: 3/8, 7/16, 1/2,
9/16 in. and/or Adjustable Wrench
• Tire Gauge
4. Literature
Pack with
Extra
Shear Bolts
Unfold Handlebar (Figure 6, 7)
1. Remove the lower and loosen the upper
wing knobs on the handlebar assembly.
2. Loosen the wing nuts on the shift rod.
3. Put the speed selector lever in the first
forward position (921002, 003, 004) or in
the sixth forward position (921001).
4. Rotate the handlebars into operating
position.
5. Install and tighten all wing knobs and
wing nuts on the handlebar assembly
and shift rod.
Figure 4
GB - 8
Install Discharge Chute and
Discharge Chute Crank (921002, 003,
004)
.
921001
(Figure 8)
1. Grease underside of discharge chute
ring (if not already greased).
2. Remove mounting hardware from auger
housing.
3. Install discharge chute over opening in
the auger housing. Finger tighten the
mounting hardware removed in step 2.
NOTE: Leave discharge chute pedestal loose
to help install the chute rod and connect it to
the control assembly.
4
3
2
1
1
OS7032
1. Handlebar
2. Wing Knobs
and Bolts
3. Wing Nuts
and Bolts
4. Speed
Selector
Lever
OS7040
2
Figure 6
3
.
4
921002, 003, 004
5
1
1
4
OS7045
1
1. Mounting
Hardware
2. Discharge
Chute
2, 3
3. Chute
Pedestal
4. Discharge
Chute Ring
Figure 8
4. Remove the cover from the gear
assembly on the discharge chute.
5. Release the lock teeth on the gear
assembly with your finger and rotate the
discharge chute 90 left.
6. Remove and save the hairpin from the
control assembly underneath the control
panel.
OS7030
1. Wing Knobs
2. Wing Nut
3. Bolt
4. Shift Rod
5. Speed
Selector
Lever
°
Figure 7
GB - 9
NOTE: Do not remove the pin installed on the
chute rod.
NOTE: To ensure the discharge chute follows
its full range of travel, make sure the control
lever is pushed all the way to the left before
installing and pinning the chute rod.
7. Align the holes on the end of the chute
rod with the mark on the gear assembly
and slide the end without a pin through
the gear assembly, through the hook on
the chute lock cable and into the hex
hole in the control assembly.
IMPORTANT: The hook will prevent the
control cable from contacting the engine or
muffler guard.
NOTE: After the chute rod has been inserted
through the hex hole in the control assembly,
placing the unit in the service position (see
Service Position on page 21) will ease
alignment and installation of the hair pin.
8. Secure the chute rod to the control
assembly with the hair pin removed in
step 6 using the end hole location as
shown in Figure 10. Insert the hair pin
with the loop end to the left of the chute
rod so the control assembly follows a full
range of travel.
921002, 003, 004
3
1
2
3
1. Chute Control
Assembly
2. Hair Pin
3. Chute Rod
Figure 10
OS7157
9. Insert the chute lock cable fitting into the
bracket on the chute pedestal, and then
connect the chute lock cable to the lock
teeth by fitting the cable ball end into the
slot on the lock teeth. See Figure 11.
NOTE: Press down on lock teeth with your
finger to align the cable ball end with the slot
(Figure 11).
2
4
1
OS7432
1.
2.
3.
4.
Chute Rod
Gear Cover
Control Assembly
Hair Pin
Figure 9
OS7271
Figure 11
10. Replace the gear cover removed in
step 4.
IMPORTANT: Rotate the discharge chute to
the left when tightening the pedestal
hardware to ensure clearance between the
discharge chute and the belt cover.
11. Tighten pedestal hardware to 15 – 31
lbf-ft (20 – 42 N•m).
12. Make sure the discharge chute rotates
left and right when you push the
discharge chute control lever left and
right.
GB - 10
Install Discharge Chute and
Discharge Chute Crank (921001)
1. Route deflector remote cable along the
left side of the chute pedestal.
2. Insert the barrel on the cable end into
the bracket on left side of chute deflector
(Figure 13).
3. Hold seal out of the way while routing
the cable through the bracket on the left
side of the discharge chute, and then
push the cable fitting into the bracket.
(Figure 12)
1. Grease underside of discharge chute
ring (if not already greased).
2. Remove mounting hardware from auger
housing.
3. Install discharge chute over opening in
the auger housing. Finger tighten the
mounting hardware removed in step 2.
NOTE: Leave discharge chute pedestal loose
to help install the chute rod and connect it to
the control assembly.
4. Push the seal securely over the end of
the cable fitting to prevent water from
entering the cable.
5. Check deflector travel. Adjust nut on
cable end under handlebar to obtain full
travel, if necessary. (see Deflector
Remote (921002, 003, 004) on
page 25).
921001
2
3
4
1
1
3
2
3
5
4
OS7061
1.
2.
3.
4.
1.
2.
3.
4.
5.
Chute Rod
Gear Cover
Control Panel
Hair Pin
Figure 12
Cable Anchor
Cable End
Deflector Cable
Cable Fitting
Cable Bracket
OS7070
Figure 13
4. Insert the short end of the chute rod into
the hole in the front of the control panel.
5. Connect the chute crank to the pinion
gear on chute with spring clip.
IMPORTANT: Rotate the discharge chute to
the left when tightening the pedestal
hardware to ensure clearance between the
discharge chute and the belt cover.
6. Tighten pedestal hardware to 15 – 31
lbf-ft (20 – 42 N•m).
Check Function of Dual Handle
Interlock
Without the engine running, press down
(engage) both clutch levers. Release
attachment clutch lever. Attachment clutch
should remain engaged until traction clutch
lever is released, then both clutches must
disengage. If they do not, contact your Dealer
for repairs.
Deflector Remote (921002, 003, 004)
Connect the cable end to the cable anchor on
the discharge deflector before clipping the
cable to the cable bracket on the discharge
chute.
GB - 11
Check Tire Pressure
Check Auger Gearcase Oil
Check tire pressure and adjust to the
pressure listed on tire sidewall.
Check oil level in auger gearcase (see Check
Auger Gearcase on page 22).
CAUTION: Avoid injury! Explosive
separation of tire and rim parts is
possible when they are serviced
incorrectly:
• Do not attempt to mount a tire
without the proper equipment
and experience to perform the
job.
• Do not inflate the tires above
the recommended pressure.
• Do not weld or heat a wheel
and tire assembly. Heat can
cause an increase in air
pressure resulting in an
explosion. Welding can
structurally weaken or deform
the wheel.
• Do not stand in front or over
the tire assembly when
inflating. Use a clip-on chuck
and extension hose long
enough to allow you to stand
to one side.
Check Engine Crankcase Oil
IMPORTANT: The engine is shipped with
5W-30 oil in crankcase. Refer to Engine
Manual for detailed instructions.
Fill Engine Fuel Tank
Refer to Engine Manual for proper fuel type
and tank capacity.
Check Function of all Controls
Ensure unit runs and performs properly. Refer
to OPERATION on page 15.
Run-in Attachment Belt
1. Start unit in a well-ventilated area
according to Starting and Shut Off on
page 19.
2. Engage attachment clutch lever and run
attachment for about 15 minutes.
3. Stop unit, wait for all moving parts to
stop, and remove spark plug wire.
4. Adjust belt finger, if necessary. See
Check Belt Finger Clearance on
page 30.
5. Adjust clutch idler according to
Attachment Clutch/Brake Adjustment on
page 27.
GB - 12
CONTROLS and FEATURES
921001
3
2
1
4
6
7
25
9
5
8
23
22
10
11 12
21
16
18
20
14
13
24
15
1. Attachment Clutch Lever
2. Speed Selector
3. Traction Drive Clutch Lever
4. Chute Control
5. Oil Fill/Dipstick
6. Discharge Chute Deflector
7. Discharge Chute
8. Impeller
9. Clean-Out Tool
10. Auger
11. Scraper Blade
12. Auger Gearcase
13. Recoil Starter Handle
14. Electric Starter
15. Wing Knobs
16. Ignition Key, Push-Pull
17. Oil Drain Plug
18. Throttle (Engine Stop)
19. Choke Control Knob
20. Primer Bulb
21. Runner
22. Axle Lock Pin
23. Belt Cover
24. Fuel Shut-Off Valve
25. Fuel Tank and Cap
19
17
3
2
1
15
OS7077
21
11
Figure 14
GB - 13
921002, 003, 004
4
18
3
5
2
1
17
7
29
8
28
10
9
6
26
25
22
21
13
24
15
11
12
14
16
27
23
1. Attachment Clutch Lever
2. Speed Selector
3. Deflector Remote Control
4. Chute Control
5. Traction Drive Clutch Lever
6. Oil Fill/Dipstick
7. Discharge Chute Deflector
8. Discharge Chute
9. Impeller
10. Clean-Out Tool
11. Auger
12. Auger Gearcase
13. Scraper Blade
14. Recoil Starter Handle
15. Electric Starter
16. Wing Knobs
17. Heated Handles (921003)
18. Remote Wheel Lock (921002)
19. Heated Handles Switch (921003)
20. Oil Drain Plug
21. Throttle (Engine Stop)
22. Ignition Key, Push-Pull
23. Choke Control Knob
24. Primer Bulb
25. Runner
26. Belt Cover
27. Fuel Shut-Off Valve
28. Fuel Tank and Cap
29. Headlight
20
5
4
3 2
1
18
19
Figure 15
OS7090
OS7080
OS7075
GB - 14
OPERATION
Attachment Clutch - Right Hand
Lever
WARNING: AVOID INJURY. Read
and understand the entire Safety
section before proceeding.
2
WARNING: To avoid injury to
hands and feet, always disengage
clutches, shut off engine, and wait
for all movement to stop before
unclogging or working on snow
thrower.
Keep hands and feet away from
auger and impeller.
1
Squeeze Attachment
Clutch Lever against
handlebar (1) to
engage attachment.
Release both clutch
levers (2) to disengage
power and apply brake
to attachment.
IMPORTANT: If the
belt squeals when the
attachment clutch lever
is engaged, the
impeller may be frozen in the auger housing.
Immediately release the attachment clutch
lever and move the unit into a heated area to
thaw.
NOTE: If belt squeals when impeller turns
freely, see Attachment Clutch/Brake
Adjustment on page 27.
OL2691
Controls AND FEATURES
See CONTROLS and FEATURES on
page 13 for all Controls and Features
locations.
Dual Handle Interlock
When Attachment Clutch and then Traction
Drive Clutch are engaged, the Attachment
Clutch will remain engaged (lever down) if
released. To stop attachment, release
Traction Drive Clutch and both clutches will
disengage.
Ignition Switch (Push/Pull Safety
Key)
Traction Drive Clutch - Left Hand
Lever
Squeeze the Traction
Drive Clutch Lever
2
against the Handlebar
(1) to engage wheel
drive for propelling unit.
Forward speed will
vary according to snow
depth and moisture
1
content.
OL2701
Release lever (2) to
stop movement.
NOTE: When traveling to or from the area to
be cleared, press down on the handlebars
enough to raise the front of the unit slightly off
the surface. Engage the traction drive clutch
without engaging the attachment drive clutch.
2
Key Switch has two
positions:
1. “Stop” - pulled out
2. "Run" - pushed in
NOTE: DO NOT twist
key after it is inserted.
1
Primer Bulb
Pushing the primer bulb in adds
fuel for easier engine start.
Refer to Starting and Shut Off
on page 19.
OS1321
Speed Selector
Position the Speed Selector in the
appropriate speed notch to control forward
and reverse travel.
Forward:
(6) Fastest
(1) Slowest
Reverse:
(1) Slow
(2) Fast
GB - 15
IMPORTANT: DO NOT change motion from
forward to reverse with clutch engaged.
Forward speed can be changed without
declutching.
921001
Recoil Starter Handle
When pulled, handle will turn engine over.
IMPORTANT: DO NOT let handle snap back
against starter.
Snow Clean-Out Tool
(Figure 16)
1 1
6
2
WARNING: Hand contact with the
rotating impeller is the most
common cause of injury associated
with snow throwers. Never use
your hand to clean out the
discharge chute.
921002, 003, 004
6
1
1
1
2
Choke Control Knob
1
2
1.Choke Closed
position: chokes
off air to engine for
easier start.
2.Choke Open
position: allows for
normal operation.
IMPORTANT: Gra
dually open choke
after engine starts.
Throttle
1
2
3
4
The throttle controls the
engine speed. To increase
or decrease the engine
speed, adjust to:
1. Fast (normal or warm
starts)
2. Part-Throttle
3. Slow (cold weather
starts)
4. Stop (engine is off)
Electric Starter
The electric starter will start a properly
choked and cranked engine when the starter
button is pushed. Refer to Starting and Shut
Off on page 19.
OS7102
Figure 16
To clear the discharge chute:
1. Shut off the engine.
2. Wait 10 seconds and make sure impeller
blades have stopped rotating.
3. Remove the snow clean-out tool (1) from
the auger housing and use it to remove
the clog from the discharge chute.
4. Replace the snow clean-out tool on the
auger housing.
Deflector Remote (921002, 003, 004)
Place deflector into position before operation.
DO NOT throw snow any higher than
necessary.
Place deflector remote in a forward notch to
throw snow lower. Place deflector remote in a
rearward notch to throw snow higher.
Discharge Deflector (921001)
ALWAYS position discharge chute deflector
at a safe angle before starting engine. DO
NOT throw snow any higher than necessary.
1. Push deflector handle forward or down
to throw snow lower.
2. Pull deflector handle up or to the rear to
throw snow higher (Figure 17).
GB - 16
Discharge Chute Crank (921001)
IMPORTANT: If chute does not stay in set
position, adjust as directed in SERVICE AND
ADJUSTMENTS on page 24, or repair before
operation.
Rotate the Chute with Discharge Chute
Crank.
921001
Figure 17
OS7103
Discharge Chute
Discharge chute rotates 200°.
ALWAYS position discharge chute in safe
direction and angle, away from operator and
bystanders, before starting engine.
Discharge Chute Control (921002,
003, 004)
OS7106
IMPORTANT: If chute does not stay in set
position, adjust as directed in SERVICE AND
ADJUSTMENTS on page 24, or repair before
operation.
Rotate the Chute with Discharge Chute
Control.
Figure 19
IMPORTANT: DO NOT force frozen chute
controls. If frozen, take to warm place until
controls are free.
Heated Handles (921003)
921002, 003, 004
1
2
Turn the heated handles
switch to the ON (1)
position to activate. Turn
the switch to the OFF (2)
position to deactivate.
OS1950
Remote Wheel Lock (921002)
OS7105
Figure 18
IMPORTANT: DO NOT force frozen chute
controls. If frozen, take to warm place until
controls are free.
Squeeze and release the remote wheel lock
to lock the left wheel for better traction when
throwing snow or to unlock the left wheel for
easier steering.
NOTE: The wheel lock will not release when
under load. Do not unlock the wheel while
turning. If the wheel lock will not release, turn
the unit slightly left or right to relieve axle load
and release the axle lock.
If remote wheel lock does not lock or unlock
properly, adjust or repair before operation
(see Remote Wheel Lock (921002) on
page 24).
GB - 17
Axle Lock Pin (921001)
Runners
(Figure 20)
Use the axle lock pin to lock or unlock the
right or left wheel. Lock both wheels to
increase traction; unlock one wheel to allow
for easier turning of the unit.
NOTE: Unit will not drive with both wheels
unlocked.
The runners control the distance between the
scraper blade and the ground. Adjust runners
equally to keep blade level with the ground.
Refer to Pre-Start on page 19 for
recommended settings.
Filling Fuel Tank
921001
WARNING: AVOID INJURY. Read
and understand the entire Safety
section before proceeding.
Wheel Unlocked
Fuel Shut-Off Valve
IMPORTANT: The fuel shut-off valve MUST
be in the closed position prior to transporting
the unit.
The fuel shut-off valve has two positions:
Closed Position: Use this
position to service, transport, or
store the unit.
Axle Lock
Pin
OS7117
Wheel Locked
OS6000
Open Position: Use this
position to run the unit.
Figure 20
Figure 21
Scraper Blade
The scraper blade allows the back of the
housing to keep better contact with the
surface being cleared. It also prevents
damage to the housing from normal wear.
To add fuel to fuel tank:
IMPORTANT: DO NOT allow Scraper Blade
to wear too far or Auger/Impeller housing will
become damaged.
1. ALWAYS place unit in open or wellventilated area.
2. Stop engine and allow to cool.
3. Clean Fuel Cap and surrounding area to
prevent dirt from entering Fuel Tank.
4. Remove Cap.
IMPORTANT: DO NOT use gasohol or
gasoline containing alcohol. See Engine
Manual for correct type and grade of fuel.
GB - 18
5. Fill fuel tank to within 1/2 in. (1.2 cm)
below bottom of filler neck with unleaded
gasoline.
NOTE: Tank capacity is 1 gallon (3.8 liters).
6. Replace Fuel Cap and tighten.
7. ALWAYS clean up any spilled fuel.
6. Check Runners
Check and adjust Runners (Runners on
page 24). Allow 1/8 in. (3 mm) between
scraper blade and hard, smooth surface(s).
Allow 1-1/4 in. (30 mm) between scraper
blade and uneven or gravel surfaces.
7. Check Engine Fuel & Crankcase
Oil
Pre-Start
1. Frozen Impeller
IMPORTANT: Before starting engine, check
impeller to be sure it is not frozen.
To check impeller:
1. With ignition key switch in “Stop”
position, squeeze Attachment Clutch
Lever to Engaged position.
2. Pull Recoil Starter Handle.
3. If Impeller is frozen, (cannot pull Starter
Handle) move unit to a heated area and
thaw to prevent possible damage.
2. Check Function of Clutches
If clutches do not engage or disengage
properly, adjust or repair before operation.
See Attachment Clutch/Brake Adjustment on
page 27 and Traction Drive Clutch
Adjustment on page 30.
WARNING: AVOID INJURY. Read
and understand the entire Safety
section before proceeding.
Check and add fuel if required. Check that
the engine crankcase oil is full using dipstick.
Refer to Engine Manual for detailed
instructions.
To Stop in an Emergency
Immediately release both control levers to
stop unit in an emergency. Stop engine,
remove key and wait for all rotating parts to
stop before leaving operator’s position.
Starting and Shut Off
3. Check Dual Handle Interlock
Without the engine running, press down
(engage) both clutch levers. Release
attachment clutch lever. Attachment clutch
should remain engaged until traction clutch
lever is released, then both clutches must
disengage.
If clutches do not engage or disengage
properly, adjust or repair before operation
(see Attachment Clutch/Brake Adjustment on
page 27 and Traction Drive Clutch
Adjustment on page 30).
4. Check Remote Wheel Lock
(921002)
Squeeze and release the remote wheel lock
to lock the left wheel for better traction when
throwing snow or to unlock the left wheel for
easier steering.
If remote wheel lock does not lock or unlock
properly, adjust or repair before operation
(see Remote Wheel Lock (921002) on
page 24).
5. Check Axle Lock (921001)
Use the axle lock pins to lock or unlock the
wheels. Lock both wheels to increase
traction; unlock one wheel to allow for easier
turning of the unit.
WARNING: FAILURE TO
FOLLOW INSTRUCTIONS could
result in personal injury and/or
damage to unit. DO NOT attempt
to start your unit at this time. Read
entire Owner/Operator Manual and
the Engine Manual first.
IMPORTANT: Allow unit and engine to adjust
to the outdoor temperature before clearing
snow. Before shut-off, run the attachment a
few minutes to prevent impeller freeze-up.
NOTE: Try out each control without the
engine running to see how it works and what
it does.
Manual Start
1. Turn discharge chute straight ahead.
2. Make sure that the traction clutch and
attachment drive clutch levers are fully
disengaged.
3. Push Primer Bulb 2 or 3 times for cold
engine.
NOTE: When temperature is below -15° F
(-26° C) additional priming may be needed.
4. If engine is cold, apply choke. See
Engine Manual for detailed instructions.
NOTE: A warm engine requires less choking
than a cold engine.
5. Set throttle to proper starting position.
6. Insert key.
120V - Push key into RUN position. DO
NOT twist key after it is inserted.
GB - 19
7. Grasp starter handle and pull rope out
slowly until it pulls harder. Let rope
rewind slowly.
8. Pull rope with a rapid continuous full arm
stroke. Let rope rewind slowly.
IMPORTANT: DO NOT let Starter Handle
snap against Starter.
9. Repeat steps 7 and 8 until engine starts.
(If engine does not start, refer to
TROUBLESHOOTING on page 36.)
10. Adjust choke as needed.
11. Set throttle to Part Throttle or Slow
position for adaptation to outside
temperature or travel. Set throttle to Fast
position for normal operation.
Electric Start (120V)
1. Connect extension cord to starter.
IMPORTANT: Prevent damage to unit. Know
voltage of your starter and only use matching
outlets.
2. Plug extension cord into 120V 3-wire,
grounded outlet.
3. Turn discharge chute straight ahead.
4. Make sure that the traction clutch and
attachment drive clutch levers are fully
disengaged.
5. Push Primer Bulb 2 or 3 times for cold
engine.
NOTE: When temperature is below -15° F
(-26° C) additional priming may be needed.
6. Insert key into ignition switch on engine
and push into "Run" position. DO NOT
twist key after it is inserted.
7. If engine is cold, apply choke. A warm
engine requires less choking than a cold
engine. See Engine Manual for detailed
instructions.
8. Set throttle to proper starting position.
9. Press starter button on engine until
engine starts.
IMPORTANT: DO NOT operate starter more
than 15 seconds per minute, as overheating
and damage can occur. (If engine does not
start, refer to TROUBLESHOOTING on
page 36.)
10. Adjust choke as needed.
11. Disconnect power cord from outlet, then
starter.
12. Set throttle to Part Throttle or Slow
position for adaptation to outside
temperature or travel. Set throttle to Fast
position for normal operation.
Shut Off
1. Release Traction Drive Clutch Lever and
allow unit to come to a complete stop.
2. Run Impeller a few minutes after use to
prevent freeze-up of Impeller.
3. Release Attachment Clutch Lever and
wait for all moving parts to come to a
complete stop.
4. Move Throttle to the “Stop” position.
5. Remove key.
Snow Removal
IMPORTANT: Allow unit and engine to adjust
to the outdoor temperature before clearing
snow.
NOTE: Attachment clutch should be engaged
before wheel drive clutch when throwing
snow.
1. Select Speed Control position and
direction.
2. Engage Attachment Clutch - Right Hand
Lever.
3. Engage Traction Drive Clutch - Left
Hand Lever.
IMPORTANT: DO NOT overload unit capacity
by attempting to clear snow at too fast a rate.
Use slow speed to clear deep or hard packed
snow.
Tips for Operation
Snow is best removed as soon as possible
after snow fall.
To clear an area, run unit in an overlapping
series of paths. For large areas, start in the
middle and throw snow to each side, so snow
is not cleared more than once.
ALWAYS direct snow away from area to be
cleared and with direction of the wind.
Traveling
To travel from one work area to another:
1. Set Throttle to Slow or Part-Throttle
position.
2. Press down on handlebars enough to
raise front of unit slightly off surface.
3. Engage wheel drive clutch without
engaging attachment drive clutch.
Transport
ALWAYS shut off engine, remove key, and
close fuel shut-off valve when transporting
unit on a truck or trailer.
Use extra care when loading or unloading
unit onto trailer or truck.
Secure unit chassis to transport vehicle.
NEVER secure from rods or linkages that
could be damaged.
DO NOT transport machine while engine is
running.
GB - 20
MAINTENANCE
Ariens Dealers will provide any service or
adjustments which may be required to keep
your unit operating at peak efficiency. Should
engine service be required, contact an Ariens
dealer or an authorized engine
manufacturer's service center.
WARNING: AVOID INJURY. Read
and understand the entire Safety
section before proceeding.
Service Position
WARNING: Before tipping unit up
onto housing, remove fuel so no
spills will occur. Ensure unit is
secure and will not tip over during
maintenance.
MAINTENANCE
SCHEDULE
Service
Performed
Each Every Every Yearly
Use 5 hrs. 25
hrs.
Check Dual
Handle
Interlock
•
Check
Fasteners
•
Check Clutch
Operation
•
*
Check Clutch
Spring
Adjustments
Place unit on a flat level surface. Tip unit
forward onto front of auger housing for
service. Ensure unit is secure and will not tip
over. Strap and clamp onto bench if needed.
Clean Engine
•
Check Engine
Oil
•
Change
Engine Oil
Service Position
•
•
**
**
•
Check Tire
Pressure
•
Check Auger
Gearcase
•
•
General
Lubrication
•
•
* After first five hours of operation.
** After first two hours of operation,
thereafter every 25 hours.
Check Dual Handle Interlock
OS7121
Without the engine running, press down
(engage) both clutch levers. Release
attachment clutch lever. Attachment clutch
should remain engaged until traction clutch
lever is released, then both clutches must
disengage.
Figure 22
Check Fasteners
MAINTENANCE SCHEDULE
Make sure all hardware is tightened properly.
The chart below shows the recommended
maintenance schedule that should be
performed on a regular basis. More frequent
service may be required.
Check Clutch Operation
Auger / impeller must stop within 5 seconds
when attachment clutch/impeller brake lever
is released.
Wheels must stop quickly when traction drive
clutch lever is released.
GB - 21
If clutches do not engage or disengage
properly, adjust or repair before operation.
See Attachment Clutch/Brake Adjustment on
page 27 and Traction Drive Clutch
Adjustment on page 30.
Clean Engine
Refer to Engine Manual for detailed
instructions.
Check engine oil
The engine crankcase oil should be checked
every 5 hours of operation. Oil level MUST be
maintained in safe operating range on
dipstick at all times or engine damage will
result (See Engine Manual).
Park unit on a level surface. Refer to Engine
Manual for detailed instructions.
Change Engine Oil
Change oil after first 2 hours of operation,
thereafter change oil every 25 hours (more
often if required). Refer to Engine Manual for
detailed instructions.
Run engine just prior to changing oil. Warm
oil will flow more freely and carry away more
contamination. Remove the oil drain plug
from the rear of the unit and tip the unit back
to help drain all the oil.
Check Auger Gearcase
IMPORTANT: Proper oil level must be
maintained.
Gear cases are filled to the correct level at
the factory. Unless there is evidence of
leakage, no additional lubricant should be
required. Check oil level each season or
every 25 hours of operation.
To ensure adequate lubricant level:
1. Remove filler plug (Figure 23). Lubricant
must be at least up to bottom of lubricant
filler hole with unit resting on a levelsurface.
2. Add lubricant if required. Allow oil to
drain to level of plug and replace plug.
IMPORTANT: Use only Ariens special gear
lubricant L-2 (Part Number 00008000).
Gearcase filler plug may require an
application of Loc-Tite® 565 thread sealant
with repeated servicing.
1
Check Tire Pressure
2
Keep tires at pressure listed on the tire
sidewall. See Check Tire Pressure on
page 12.
1. Auger Gearcase
2. Oil Fill and Drain Plug
Figure 23
GB - 22
OS7132
General Lubrication
IMPORTANT: Wipe each fitting clean before
and after lubrication. Do not wipe gearcase
filler plug; wiping the gearcase filler plug may
remove thread sealant and cause leaks.
IMPORTANT: DO NOT allow grease or oil to
get on friction disc, friction plate or belts.
NOTE: Apply Ariens Hi-Temp Grease or
equivalent to the lubrication fittings. See
SERVICE PARTS on page 35.
Sno-Thro should be lubricated (Figure 24) at
beginning of season or every 25 operating
hours.
921002, 003,
004
Grease
Oil
921001
921002
921003, 004
Figure 24
GB - 23
OS7136
OS7141
OS7142
OS7143
SERVICE AND ADJUSTMENTS
Shear Bolts
WARNING: AVOID INJURY. Read
and understand the entire Safety
section before proceeding.
Scraper Blade
IMPORTANT: Damage to auger/impeller
housing will result if blade wears down too
far.
Scraper blade is adjustable to compensate
for wear.
To adjust scraper blade:
1. Tip unit back onto handlebar, support
housing and loosen nuts retaining blade.
2. Adjust runners to fully raised position
(housing closest to ground).
3. Reposition scraper blade flush with
runners and tighten lock nuts.
IMPORTANT: Use only Ariens shear bolts for
replacement. Use of any other type of shear
bolt may result in severe damage to unit. See
SERVICE PARTS on page 35.
Occasionally a foreign object may enter the
auger/impeller housing and jam the auger,
breaking shear bolts (Figure 26) which
secure the auger to the shaft. This allows
auger to turn freely on the shaft preventing
damage to gear drive.
1
Runners
Runners should be adjusted as conditions
require (Figure 25).
1. Position unit on a hard, flat, smooth level
surface.
2. Adjust runners by inserting a spacer of
desired thickness under center of
scraper blade, loosen runner hardware,
slide runners to flat surface. Allow 1/8 in.
(3 mm) between scraper blade and hard
smooth surfaces. Allow 1-1/4 in.
(30 mm) between scraper blade and
uneven or gravel surfaces. Retighten
hardware.
NOTE: Keep housing level by adjusting
runners equally.
OS7150
2
1. Auger
2. Shear Bolts
Figure 26
For Replacement:
1. Align shear bolt holes in auger with
shear bolt holes in the shaft.
2. Drive shear bolt through hole (if shear
bolt was broken this will drive remaining
part from shaft).
3. Secure shear bolt with nut.
Remote Wheel Lock (921002)
2
1
1. Runner
2. Runner Hardware
Figure 25
OS0482
If remote wheel lock does not lock or unlock:
1. Place unit in service position (see
Service Position on page 21).
2. Loosen jam nuts on cable. Make sure
the bottom jam nut is loosened enough
to remove slack from cable (Figure 27).
3. Pull the cable adjuster to remove slack
between the cable adjuster and the
extension spring and hold the cable
adjuster in position while finger
tightening the top jam nut against the
bracket. Do not extend the spring or
engage the mechanism.
4. Tighten the bottom jam nut.
GB - 24
5. Check function of remote wheel lock. If
wheel lock does not function properly,
remove bottom cover to check cable
slack.
6. Repeat steps 2 – 4 while watching cable
to remove slack.
7. Check function of remote wheel lock. If
wheel lock does not function properly,
take the unit to Dealer for repairs.
921002, 003, 004
Tighten nut.
1
3
OS7175
No Slack
1
OS7170
2
2
1. Adjusting Nuts
2. Cable Support Bracket
1. Top Jam Nut
2. Bottom Jam Nut
3. Cable Adjuster
Figure 28
Figure 27
Discharge Chute (921002, 003,
004)
Deflector Remote (921002, 003,
004)
Deflector must stay in selected position while
throwing snow.
If deflector does not stay in set position:
1. Tighten nut beneath control panel to
increase pressure on deflector control
(Figure 28).
If deflector does not follow full range of travel:
1. Push deflector remote all the way
forward.Pull deflector all the way back.
2. Loosen adjusting nuts on cable support
bracket underneath the dash panel
(Figure 28).
3. To adjust the deflector lower:
Slide cable down. Tighten bottom nut.
4. To adjust deflector higher:
Slide cable up. Tighten top nut.
5. Check travel and repeat adjustment as
necessary.
If chute does not stay in position while
throwing snow or if chute does not rotate
freely, adjust the cable under the control
panel so the chute lock fingers engage or
disengage the locking gear.
If chute does not stay in position:
Loosen the cable by loosening the lower
adjustment nut, and then tightening the upper
adjustment nut against the bracket
(Figure 29).
GB - 25
Discharge Chute Deflector
(921001)
921002, 003, 004
Deflector must stay in selected position while
blowing snow.
To adjust, loosen then retighten hardware to
desired deflection drag force (Figure 31).
Tighten upper
adjustment nut.
921001
Discharge Chute
Deflector
Adjusting
Hardware
OS7180
Loosen lower
adjustment nut.
Figure 29
If chute does not rotate freely:
Tighten the cable by loosening the upper
adjustment nut, and then tightening the lower
adjustment nut against the bracket
(Figure 30).
Discharge
Chute
921002, 003, 004
OS7176
Figure 31
Loosen upper
adjustment nut.
Discharge Chute (921001)
If discharge chute does not stay in position
while operating, tighten nut on carriage bolt at
pivot point to increase tension on spring
(Figure 32).
OS7180
Tighten lower
adjustment nut.
Figure 30
GB - 26
8. Adjust pivot pin on the shift rod as
necessary so unit travels forward when
speed selector is in first forward position
and travels backward when speed
selector is in first reverse position.
9. Connect the pivot pin to the speed
selector arm with the hardware removed
in step 1.
921001
4
1
1
2
1
3
OS7186
OS7177
2
2
1. Spring
2. Nut
1.
2.
3.
4.
Figure 32
Speed Selector Adjustment
To adjust (Figure 33):
1. Disconnect adjustment pivot pin from
speed selector lever by removing hair
pin.
2. Place the speed selector in the fastest
forward speed position.
3. Turn the speed selector lever straight
down towards the ground as far as it will
go.
4. Thread the adjustment pivot pin along
the shift rod until it aligns with the mating
hole on the speed selector lever. Insert
the pivot pin into hole.
5. Secure adjustment pivot pin with hairpin.
6. Make sure the speed selector shifts into
each speed position.
7. Check forward and reverse speeds:
a. Start unit.
b. Shift speed selector into the first
forward speed.
c. Engage the traction clutch. Unit
should move forward.
d. Stop unit.
e. Shift speed selector into first
reverse speed.
f. Engage the traction clutch. Unit
should move backward.
g. Shut off unit.
Shift Rod
Adjustment Pivot Pin
Speed Selector Lever
Hairpin
Figure 33
Attachment Clutch/Brake
Adjustment
(Figures 34, 35 and 36)
IMPORTANT: IMPROPER
ADJUSTMENT could result in
unexpected movement of auger
and impeller causing death or
serious injury. Auger / impeller
must stop within 5 seconds when
Attachment Clutch/Impeller Brake
lever is released.
Remove Attachment Cable Slack
GB - 27
1. Remove the belt cover.
2. Loosen jam nut on cable adjustment
barrel, and then turn the adjustment
barrel up or down to lengthen or shorten
cable and remove all cable slack. See
Figure 34.
• If roller is less than 1/2 in. (12.7 mm)
from frame, loosen idler adjustment nut
and move idler closer to the belt. Tighten
adjustment nut and recheck the roller
clearance.
1
2
OS7182
OS7184
1. Adjustment
Barrel
2. Jam Nut
Figure 34
3. With the attachment clutch disengaged,
check that the attachment idler arm
lightly touches the frame. See Figure 35.
With the attachment clutch disengaged,
check the attachment idler arm position
here. The attachment idler arm should
lightly touch the frame.
OS7189
Roller should be a minimum of 1/2 in.
(12.7 mm) from the frame when the
attachment clutch is engaged.
Figure 36
Adjust the Attachment Clutch Cable
Spring Extension
1. Check the attachment clutch cable
spring extension.
Measure the length of the attachment
clutch cable spring with the clutch lever
disengaged.
Then measure the attachment clutch
spring with the clutch lever engaged.
See Figure 37.
• If spring extension is within the specified
range, go to Check Attachment Brake on
page 29.
• If spring extension is outside of specified
range, go to step 2.
OS7194
Figure 35
4. Tighten jam nut on the adjustment
barrel.
Check Attachment Idler Arm Roller
Clearance
1. Place the unit into the service position.
Remove the bottom cover.
2. With the clutch lever engaged, check the
clearance between the frame and plastic
roller on the lower end of the attachment
idler arm. See Figure 36.
• If roller is 1/2 in. (12.7 mm) or more from
frame, go to Adjust the Attachment
Clutch Cable Spring Extension on
page 28.
GB - 28
2
3
1
1/2 – 9/16 in.
(12.7 –- 14.3 mm)
4
5
Figure 37
1.
2.
3.
4.
5.
OS7184
OS7183
2. Adjust attachment idler position. See
Figure 38.
a. Loosen idler adjustment nut.
b. To increase spring extension,
move idler closer to belts and
tighten adjustment nut. Return to
Step 1.
c. To decrease spring extension,
move idler away from belts and
tighten adjustment nut. Return to
Step 1.
OS7194
OS7221
Engine Sheave
Attachment Drive Belts
Belt Finger
Attachment Belt Idler
Attachment Idler Adjustment Nut
Figure 38
Check Attachment Brake
See Figure 39.
1. With the clutch lever disengaged, brake
pad must contact attachment belts. With
clutch lever engaged, brake pad must be
more than 1/16 in. (1.6 mm) from belts. If
there is more than 1/16 in. (1.6 mm) gap,
go to Check Belt Finger Clearance on
page 30. If there is less than 1/16 in. (1.6
mm) gap, go to Step 2.
3
1
OS7188
2
Minimum of 1/16 in.
(1.6 mm).
1. Attachment Drive Belt
2. Brake Shoe and Pad
3. Attachment Pulley
Figure 39
GB - 29
2. If there is less than 1/16 in. (1.6 mm)
gap between brake pad and belts, follow
these steps:
a. To increase brake pad gap,
loosen idler adjustment nut, and
move idler away from belt.
Position idler to achieve a 1/16 in.
(1.6 mm) minimum brake pad gap
and a 1/2 in. (12.7 mm) minimum
gap between the plastic roller and
the frame.
b. Check the clutch cable spring
extension and adjust as
necessary to achieve a 7/16 –
9/16 in. (11.1 – 14.3 mm) spring
extension.
c. If the cable needed adjustment,
recheck gaps described in step
2a. Repeat steps as necessary
until brake clearance, roller gap
and spring extension are within
specified ranges.
IMPORTANT: If adjustments cannot be
brought into specified ranges see your Dealer
for repairs.
1
2
Check belt finger clearance here. With
the attachment clutch engaged, there
should be less than 1/8 in. (3 mm)
clearance between the belts and the
belt finger. The belt finger should not
touch the belts.
1. Mounting Hardware
2. Belt Finger
Check Belt Finger Clearance
1. With clutch lever engaged, the belt
finger located opposite the belt idler
must be less than 1/8 in. (3 mm) from
belts, but not touching the belts.
To adjust belt finger, loosen the bolts and
move the finger to the proper position.
Tighten the bolts and recheck the belt
finger clearance.
Figure 40
OS7194
2. Replace the belt cover.
Traction Drive Clutch Adjustment
If drive slips, adjust traction clutch to
compensate for friction disc wear.
To adjust traction clutch:
1. Place speed selector in first forward
speed.
2. With the engine OFF, push unit forward
while slowly moving the traction drive
clutch lever toward the handlebar.
3. Measure the distance between the lever
and handlebar when the wheels begin to
brake. The distance should be: 7-1/2 – 8
in. (190.5 – 203.2 mm) (921001), 7 – 71/2 in. (177.8 – 190.5 mm) (921002,
003, 004). See Figure 41. If distance is
out of range, adjust the traction clutch.
GB - 30
921001:
7-1/2 – 8 in.
(190.5 – 203.2 mm)
1
2
3
921002, 003, 004:
7 – 7-1/2 in.
(177.8 – 190.5 mm)
Figure 41
OS7208
OS7206
4. To adjust traction clutch (Figure 42):
a. With the traction drive clutch
lever disengaged, loosen the jam
nut on the cable adjuster.
b. Turn the adjuster body up the
cable to decrease the distance
between the clutch lever and
handlebar.
c. Turn the adjuster body down the
cable to increase the distance
between the clutch lever and
handlebar.
GB - 31
1. Traction Clutch Cable
2. Adjuster Body
3. Jam Nut
Figure 42
5. Check the traction clutch lever distance
and repeat adjustment steps if
necessary.
6. Tighten the jam nut on the traction cable
adjustor body.
7. With the clutch disengaged, check that
there is more than 1/32 in. (0.8 mm)
clearance between friction disc and
drive plate assembly (Figure 43).
CAUTION: Always support SnoThro frame and blower housing
when loosening the cap screws
holding them together. Never
loosen cap screws while unit is
in service position.
8. Remove hex bolts securing housing to
frame (two on each side). Tip housing
and frame apart on pivot pin (Figure 44).
9. Remove attachment drive belts from
attachment pulley (hold brake away from
belt).
921001
OS7144
>1/32 in.
(.8 mm)
Figure 43
IMPORTANT: If traction clutch cannot be
adjusted within specified range, see your
Dealer for repairs.
Attachment Drive Belt
Replacement
921002, 003, 004
Remove old attachment drive belts:
1. Shut off engine, remove key, disconnect
spark plug wire and allow unit to cool
completely.
2. Remove belt cover and chute gear cover
(921002, 003, 004) (Figure 44).
3. Rotate discharge chute all the way to the
left (as viewed from the operator’s
position).
4. 921002, 003, 004: Remove hair pin
under the control panel connecting the
discharge chute rod to the chute rotation
lever and slide the discharge chute rod
forward.
921001: Remove spring pin from chute
crank and separate.
IMPORTANT: Disconnect chute lock cable
and deflector cable, if equipped (921002,
003, 004).
5. Remove belt finger (Figure 40).
6. Remove attachment drive belt from
engine sheave (it may be necessary to
turn engine sheave using recoil starter
handle).
IMPORTANT: To avoid bending bottom cover
when tipping unit apart, support handlebars
firmly or tip unit up on housing and remove
bottom cover by removing six cap screws
before separating unit.
7. Support Sno-Thro frame and housing.
Figure 44
Install new attachment drive belts:
1. Place new attachment belts onto
attachment pulley.
NOTE: Holding down the attachment clutch
lever will make it easier to reconnect the
housing and frame.
2. Tip housing and frame back together
and secure with hex bolts.
3. Place belt onto engine sheave.
4. Reposition and secure belt fingers.
IMPORTANT: With clutch lever engaged, belt
finger on the side opposite the belt idler
should be less than 1/8 in. (3 mm) from belt,
but not touching the belt. Adjust belt finger as
necessary.
GB - 32
2
1
7
2
7
4
3
3
6
5
1. Traction
Drive Belt
2. Engine
Sheave
3. Attachment
Drive Belts
4. Belt Finger
5. Attachment
Belt Idler
5
1
6. Attachment
Idler
Adjustment
Nut
7. Traction Belt
Idler
6
4
OS7144
Figure 45
1. Spacer
2. Drive Plate
Assembly
3. Traction Belt
Idler
4. Attachment
Drive Belts
OS7198
5. Check adjustment. See Attachment
Clutch/Brake Adjustment on page 27
WARNING: AUGER /
IMPELLER MUST STOP within
5 seconds when attachment
clutch lever is released or unit
damage or serious injury may
result.
5. Traction Drive
Belt
6. Engine
Sheave
7. Friction Disc
Figure 46
6. Reconnect chute crank and secure with
spring clip. Reconnect chute lock cable
and deflector cable.
7. Replace belt cover.
Traction Drive Belt Replacement
NOTE: Replacement will be easier with
housing and frame tipped apart and bottom
cover off.
1. Remove attachment drive belts (see
Attachment Drive Belt Replacement on
page 32).
2. To gain belt clearance, remove swing
gate spacer and slide drive plate over so
that finger clears stop hole in frame and
can swing past it. See Figure 46.
3. Pull idler away from traction drive belt
and remove belt from idler pulley, engine
sheave and driven pulley (it may be
necessary to turn engine pulley using
recoil handle).
4. Install new traction drive belt onto
attachment pulley and engine sheaves.
5. Swing drive plate toward friction disc
until finger lines up with stop hole in
frame. Slide drive plate over, inserting
finger into stop hole. Reinstall drive plate
spacer.
NOTE: Make sure the drive plate assembly
return spring remains connected to the frame
and nylon bushing is in drive plate pivot hole.
6. Replace attachment drive belt (See
Attachment Drive Belt Replacement on
page 32).
GB - 33
Friction Disc Replacement
3
1. Shut off engine, remove key, disconnect
spark plug wire and allow unit to cool
completely.
2. Place unit into service position on a level
surface.
3. Remove both wheels.
4. Remove bottom cover by removing six
hex bolts.
5. Disconnect pivot pin from the speed
selector arm. Save the hardware for
reinstallation.
6. Remove spring clip pin nearest drive
sprocket from hex shaft.
7. Remove left bearing flange from frame.
8. Slide hex shaft to the left to remove
pinion sprocket and friction disc
assembly from hex shaft.
9. Remove friction disc assembly from
frame.
10. Remove three screws holding friction
disc to carrier bearing.
11. Remove old friction disc. Put the friction
disc in place, cup side to carrier bearing.
12. Reinstall three screws into new friction
disc and carrier bearing.
13. Insert new friction disc assembly into
frame. Install washers into carrier
bearing and slide into speed selector
arm.
14. Replace bottom cover.
15. Adjust traction drive clutch (see Traction
Drive Clutch Adjustment on page 30).
5
1
2
GB - 34
4
OS7142
6
1. Hex Shaft
2. Bearing
Cap
3. Speed
Selector
Arm
4. Friction
Disc
5. Spring Clip
6. Drive Plate
Assembly
Figure 47
SERVICE PARTS
STORAGE
Order the following parts through your
Dealer:
Part No.
WARNING: AVOID INJURY.
Read and understand the entire
Safety section before
proceeding.
Description
00036800 Ariens Hi-Temp Grease
(3, 3 oz. cartridges)
21533400 Spark Plug
Short Term
07200431 Impeller Belt (2)
IMPORTANT: NEVER spray unit with high
pressure water or store unit outdoors.
Run with attachment clutch engaged a few
minutes after each use to free unit of any
loose or melting snow.
Close fuel shut-off valve.
Inspect unit for visible signs of wear,
breakage or damage.
Keep all nuts, bolts and screws properly
tightened and know unit is in safe working
condition.
Store unit in a cool, dry protected area.
07200111
Long Term
72406900 Slicer Bar
Traction Belt
00170800 Friction Disc
52100100 Shear Bolt Kit
ACCESSORIES
See your authorized Ariens dealer to add
the additional accessories available to your
Sno-Thro.
Part No.
Description
72406500 Front Weight Kit
Clean unit thoroughly with mild soap and low
pressure water and lubricate (see
MAINTENANCE on page 21). Touch up all
scratched painted surfaces.
Remove weight from wheels by putting
blocks under frame or axle.
Fuel System
Gasoline left in the fuel system for extended
periods without a stabilizer will deteriorate,
resulting in gum deposits in the system.
These deposits can damage the carburetor
and the fuel hoses, filter and tank. Prevent
deposits from forming in the fuel system
during storage by adding a quality fuel
stabilizer to the fuel. Follow the
recommended mix ratio found on the fuel
stabilizer container.
To treat the fuel system for storage:
1. Add fuel stabilizer according to
manufacturers’ instructions.
2. Run engine for at least 10 minutes after
adding stabilizer to allow it to reach the
carburetor.
NEVER store the engine with fuel in the fuel
tank inside of a building with potential
sources of ignition.
GB - 35
TROUBLESHOOTING
PROBLEM
Engine will not
crank/start.
Engine stops.
PROBABLE CAUSE
CORRECTION
1. Fuel tank is empty.
2. Fuel shut-off valve closed.
3. Build up of dirt and residue
around
governor/carburetor.
4. Key Switch not in run
position.
5. Electric starter not
functioning.
1. Fill fuel tank.
2. Open fuel shut-off valve.
3. Clean area around
governor/carburetor.
1. Out of fuel.
2. Fuel shut-off valve closed.
3. Mechanical jam in blower
rake or impeller.
1. Fill fuel tank.
2. Open fuel shut-off valve.
3. Turn off engine, remove key, and
wait for all moving parts to stop.
Check for and remove
obstruction and repair before
restart.
4. Replace with clean fuel.
5. Replace or clean spark plug.
4. Polluted fuel supply.
5. Faulty spark plug.
Engine
problems.
1. See Engine Manual.
Does not
operate in
Forward /
Reverse.
1. Friction disc not adjusted
properly.
2. Traction belt not
functioning.
3. Speed selector not
adjusted properly.
4. Put Key Switch into run position.
5. Check for a bad starter or
connections.
1. Repair or replace friction disc.
See on page 34
2. Repair or replace traction drive
belt. See Traction Drive Belt
Replacement on page 33
3. Adjust speed selector. See
Speed Selector Adjustment on
page 27
Small rubber
beads collect
in frame
1. Friction disc wear.
1. Normal friction disc wear. Chunks
or large pieces of rubber mean
friction disc should be checked
and replaced as necessary.
Unit throws
snow poorly or
does not throw
snow.
1. Shear bolts broken.
1. Replace shear bolts (see Shear
Bolts on page 24).
2. Adjust attachment clutch/brake
(see Attachment Clutch/Brake
Adjustment on page 27).
3. Move unit to a warm place to
thaw.
4. With the engine off and auger
disengaged, check for
obstructions and remove.
5. Adjust or replace attachment
drive belts (see Attachment Drive
Belt Replacement on page 32).
2. Attachment clutch/brake
not adjusted properly.
3. Auger is frozen in place.
4. Ice or debris is obstructing
auger.
5. Attachment drive belts
slipping, worn or damaged.
GB - 36
SPECIFICATIONS
Model Number
Description
921001
921002
921003
921004
ST824E
ST1027LE
ST1130DLE
ST924DLE
Engine -
Tecumseh
LH318SA
Tecumseh
LH358SA
Tecumseh
LH358SA
Tecumseh
LH318SA
Power Max - HP (kW)
8.0 (5.97)
10.0 (7.46)
11.0 (8.20)
9.25 (6.90)
Fast Idle Speed RPM (min-1)
Displacement - in.
(cc)
3600 ± 150
19.4 (318)
21.8 (358)
21.8 (358)
Electric Start
120V
Fuel
See Engine Manual
Tank Capacity - qt
(Liters)
Snow Clearing
Width - in. (cm)
19.4 (318)
4 (3.8)
24 (61.0)
27 (68.6)
30 (76.2)
24 (61.0)
Yes
Yes
Chute
Rotation Angle
200°
Rotation Control
at Handlebar
Yes
Remote Deflector
Control
No
Yes
Impeller
Diameter - in. (cm)
14 (35.6)
Speed - RPM Max (min-1)
1156
Auger
Diameter - in.
(cm)
14 (35.6)
Speed - RPM Max (min-1)
119
Auger Brake
Yes
Attachment
Clutch
Yes
Drive
Disc-O-Matic
Speeds
Lock Out
Differential
6 Forward and 2 Reverse
Pin-Lock
Pneumatic Tires in. (cm)
Remote Wheel
Lock
Auto Differential
Lock
Auto Differential
Lock
15/5 x 6 (38.1/12.7 x 15.2)
Size and Weight
Length - in. (cm)
55.4 (140.7)
57.91 (147.1)
57.91 (147.1)
57.91 (147.1)
Height - in. (cm)
44.5 (113.3)
44.25 (112.4)
44.25 (112.4)
44.25 (112.4)
Width - in. (cm)
26.4 (67.1)
29.4 (74.7)
32.4 (82.3)
26.4 (67.1)
Weight - lbs (Kg)
228 (103.4)
242 (109.8)
245 (111.1)
237.4 (107.7)
GB - 37
Ariens Limited
Warranties
2-Year Limited Lawn and Garden
Consumer Warranty
Ariens Company (Ariens) warrants to the
original purchaser that Ariens and Gravely
brand consumer products manufactured by
Ariens Company will be free from defects in
material and workmanship for a period of two (2)
years after the date of purchase, and that Ariens
will repair any defect in material or workmanship,
and repair or replace any defective part, subject
to the conditions, limitations and exclusions set
forth herein. Such repair or replacement will be
free of charge to the original purchaser (labor
and parts), except as noted below.
The two-year duration of this warranty applies
only if the product is put to ordinary, reasonable,
and usual personal, family, or household uses. If
the product is put to any business, commercial,
or industrial use such as, but not limited to,
commercial landscaping, mowing or snow
removal services, or golf course or park
maintenance, or agricultural or farmstead use,
then the duration of this warranty is ninety (90)
days after the date of purchase, or one (1) year
after the date of purchase if the product is
labeled as a Professional/Commercial Product.
The duration of this warranty shall be ninety (90)
days after the date of purchase if any product is
rented or leased.
2-Year Limited Lawn and Garden
Commercial Warranty
The Ariens Company (Ariens) warrants to the
original purchaser that all Gravely Pro and
ProMaster products manufactured by Ariens will
be free from defects in material and
workmanship for a period of two (2) years after
the date of purchase or 1000 hours of use,
whichever comes first. An authorized Gravely
dealer will repair any defect in material or
workmanship, and repair or replace any
defective part, subject to the conditions,
limitations and exclusions set forth herein. Such
repair or replacement will be free of charge to
the original purchaser (labor and parts), except
as noted below.
The duration of this warranty shall be ninety
(90) days after the date of purchase or 1000
hours of use, whichever comes first, if any
product is rented or leased.
3-Year Limited Sno-Thro Warranty
Ariens Company (Ariens) warrants to the
original purchaser that Sno-Thro products
manufactured by Ariens Company will be free
from defects in material and workmanship for a
period of three (3) years after the date of
purchase, and will repair any defect in material
or workmanship, and repair or replace any
defective part, subject to the conditions,
limitations and exclusions set forth herein. Such
repair or replacement will be free of charge to
the original purchaser (labor and parts), except
as noted below.
The three-year duration of this warranty
applies only if the product is put to ordinary,
reasonable, and usual personal, family, or
household uses. If the product is put to any
business, commercial, or industrial use, then the
duration of this warranty is ninety (90) days after
the date of purchase, or one (1) year after the
date of purchase if the product is labeled as a
Professional/Commercial Product. The duration
of this warranty shall be ninety (90) days after
the date of purchase if any product is rented or
leased.
DURA-CLEAN™ Auger Limited
Lifetime Warranty
Ariens Company (Ariens) warrants to the
original purchaser that the rubber components
of the DURA-CLEAN™ Auger manufactured by
Ariens Company will be free from defects in
material and workmanship and will not wear out
for the life of the Sno-Thro, except as noted
below.
Ariens Company will provide for the
replacement of any of the rubber components of
the DURA-CLEAN™ Auger found upon
examination by the Ariens Company to be
defective or worn out. Replacements will be
supplied free of charge. Labor is not included
after two (2) years from the date of purchase of
the Sno-Thro.
The lifetime limited warranty shall apply if the
product is put to ordinary, reasonable, and usual
personal household use. If the product is put to
any business, commercial, industrial, rental, or
leased use, the warranty shall be against defects
in material and workmanship for ninety (90) days
following the date of purchase.
Ariens Company • 655 W. Ryan St, •
Brillion, WI 54110-1072 • (920) 756-2141 • www.ariens.com
ALW2-62905
Exceptions, Limitations, Exclusions
These warranties are subject to the following conditions, limitations, and exclusions:
The following items are excluded from this
To obtain warranty service, the following
warranty:
conditions must be met:
• Engines and enty and are not covered by this
• The purchaser must perform the
warranty.
maintenance and minor adjustments
• Hydro-Gear transmissions and/or
explained in the owner’s manual.
Hydro-Gear drive components are covered
• The purchaser must promptly notify Ariens
only by the Hydro-Gear warranty and are
Company or an authorized Ariens service
not covered by this warranty.
representative of the need for warranty
• Parts that are not genuine Ariens or
service.
Gravely brand service parts are not
• The purchaser must transport the product
covered by this warranty.
to and from the place of warranty service.
• Except as specifically warranted, normal
• Warranty service must be performed by a
maintenance, services, and normal
respective Ariens or Gravely authorized
replacement items, such as spark plugs,
service representative.
oil, oil filters, air filters, mufflers, belts, tires,
• To find an Ariens or Gravely authorized
shoes, runners, scraper blades, shear
service representative, contact Ariens at:
bolts, mower blades, mower vanes,
655 W. Ryan St, P.O. Box 157
headlights, light bulbs, knives, etc. are not
Brillion, WI 54110-0157
covered by this warranty except as noted
(920) 756 - 2141
below.
www.ariens.com
• Mufflers, belts, and tires on consumer lawn
www.gravely.com
and garden products are warranted to the
original purchaser for two years.
This warranty is subject to the following
• Friction discs, idlers, cables, and electrical
limitations:
components on Sno-Thros put to usual
• Genuine Ariens or Gravely brand service
personal household use are warranted to
parts and accessories not purchased with
the original purchaser for two years.
the product covered by this warranty, but
• Any defect which is the result of misuse,
which are later purchased and used with
alteration, improper assembly, improper
that product, are warranted to be free from
adjustment, neglect, or accident is not
defects in material and workmanship for a
covered by this warranty.
period of ninety (90) days after date of
This warranty applies only to products
purchase, and Ariens Company will repair
purchased in the United States (including Puerto
or replace any such part or accessory free
Rico) and Canada. In all other countries, contact
of charge, except for labor, during that
place of purchase for warranty information.
period.
• Batteries are warranted only for a period of
twelve (12) months after date of purchase,
on a prorated basis. For the first ninety (90)
days of the warranty period, a defective
battery will be replaced free of charge. If
the applicable warranty period is more than
90 days, Ariens Company will cover the
prorated cost of any defective battery, for
up to twelve (12) months after the date of
purchase.
Ariens may from time to time change the design of its products. Nothing contained in this warranty
shall be construed as obligating Ariens to incorporate such design changes into previously
manufactured products, nor shall such changes be construed as an admission that previous designs
were defective.
LIMITATION OF REMEDY AND
DAMAGES
DISCLAIMER OF FURTHER
WARRANTY
Ariens Company’s liability under this warranty,
and under any implied warranty that may exist, is
limited to repair of any defect in workmanship,
and repair or replacement of any defective part.
Ariens Company shall not be liable for incidental,
special, or consequential damages (including
lost profits). Some states do not allow the
exclusion of incidental or consequential
damages, so the above limitation or exclusion
may not apply to you.
Ariens Company makes no warranty, express
or implied, other than what is expressly made in
this warranty. If the law of your state provides
that an implied warranty of merchantability, or an
implied warranty of fitness for particular purpose,
or any other implied warranty, applies to Ariens
Company, then any such implied warranty is
limited to the duration of this warranty. Some
states do not allow limitations on how long an
implied warranty lasts, so the above limitation
may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state.
Ariens Company • 655 W. Ryan St. •
Brillion, WI 54110-1072• (920) 756-2141 • www.ariens.com
ALW2-62905
Ariens Company
655 West Ryan Street
Brillion, WI 54110-1072
920-756-2141
Fax 920-756-2407
www.ariens.com