WASHING MACHINE
Owner’s Instructions
SW-903(P)/SWT90C1(P)/SWT90C2(P)
BEFORE USING THE WASHING MACHINE 1
PRECAUTIONS
1
CONTROL PANEL
2
DESCRIPTION AND CLEANING OF PART 2
WASHING PROCEDURE
3
To Wash
3
To Spin Dry
3
To Rinsing
4
Overflow rinse
4
Additional rinse
4
INSTALLATION
5
Location
5
Mounting the legs
5
Connecting the drain hose
5
Changing the position of the drain hose 5
LAUNDRY GUIDE
5
MAINTENANCE
6
TROUBLE SHOOTING
6
Before operating the washing machine, please read this manual
thoroughly, and retain it for future reference.
IF YOU NEED HELP.
Do not hesitate to call your local Samsung Service Center.
They will be pleased to help you. Be sure to give them your name,
address, telephone number and the purpose of the call.
SPECIFICATIONS
DIMENSIONS SWT90C1(P)/SWT90C2(P)
820 x 524 x 1000 mm
SW-903(P)
820 x 524 x 920 mm
WT10S0(P)/WT10S1(P)/WT10S2(P)
820 x 524 x 993 mm
WATER PRESSURE
0.05~0.78 MPa(0.5 ~ 8.0kg . f/cm2)
WEIGHT
36 kg
EXTRACTION EFFICIENCY
50 %
STANDARD QUANTITY OF WATER
Low : 44 l
RATING TIME
Washing 1 Hour / Spinning 15 minutes
Middle : 56 l
High : 67 l
DC68 - 01288A-01
BEFORE USING THE WASHING MACHINE
• Remove the cap-hose
from the drain hose.
• In the case of pump drained
washer, remove
the cap-hose from
the drain hole.
PRECAUTIONS WHEN OPERATING
• Don't use excessively hot water.
(50˚C or more)
Plastic parts may be deformed or damaged.
Also, clothing may be deformed or decolored.
• Before washing,check all pockets.
If nails or pins remain in pockets,they may
damage the washer or clothes.
• Close the water tap a little if the
water pressure is too high.
• Never splash water on the control panel.
• Be sure to cover with the inner
cover on laundry before spinning.
This prevents laundry from
being tossed out and damaged.
• To avoid water splashes, close the
wash tub lid.
• Be sure laythe drain hose down.
(in case no drain pump)
CAUTIONS
• Be sure that the washer is grounded.
To avoid electrical shock,use a
metal pipe for the ground
connection. But, don't ground the
washer with gas pipes or telephone
lines to avoid to dangers of explosion
or lightning strike.
• Do not put your hands into the
spin dryer basket when it is
spinning.
Your fingers can be caught by
spinning laundry and damaged.
CONTROL PANEL
1. WASH TIMMER
This is used to set the
wash time, 1-15 minutes.
0
15
3
12
6
9
WASH TIMER
2. CYCLE SELECTOR
This is used to set the
Washing/Rinsing
or Draining.
Wash/Rinse
Wash
Drain Rinse
CYCLE SELECTOR
3. SPIN DRY TIMER
This is used to set the
spin time, 1-5 minutes.
Drain
CYCLE SELECTOR
0
5
1
4
2
3
SPIN DRY TIMER
• Never allow children to operate
or play with the washer.
Children playing with the
washer may accidentally
fall into the washing tub.
4. WATER SELECTOR
During washing, WATER SELECTOR
KNOB should be selected.
Spin
Wash
During spin rinsing, WATER
WATER SELECTOR
SELECTOR KNOB should
be selected.
• Disconnect the power cord from the
power supply when not in use.
5. WASH SELECTOR(CONTROL)
• Ventilation opening must not be obstructed
by carpeting when the washing machine is
installed on a carpeted floor.
• If the supply cord of this appliance is
damaged, it must only be replaced by a repair
shopappointed by the manufacturer, because
special purpose tools are required.
• Warning to avoid overfilling and damages this
appliance must be filled with the operator
present using a moderate water supply
pressure only.
• Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
• To avoid overfilling and damages this appliance
must be filled with the operator present using a
moderate water supply pressure only.
1
Normal
Delicate
(LITE)
Normal
Heavy
WASH CONTROL
Soft
Heavy
WASH SELECTOR
This is used to select wash action.
You can wash laundry effectively
by various methods.
6. DRAIN SELCTOR
Be sure to press the selector
knob to “WASH” while washing.
7. WATER INTAKE
Connect water inlet to
a tap with a suitable.
Drain
Wash
DRAIN SELECTOR
WATER INTAKE
DESCRIPTION AND /CLEANING OF PARTS
SPIN DRYER LID
When you open this
lid while the spin basket is
spinning,the spinning will
be stopped by the brake
system.
SPIN DRYER BASKET
INNER LID
DRAIN HOSE
(with pump)
POWER CORD
The plug’s shape
may not be similar to that
shown in this drawing.
OVERFLOW
FILTER
LINT FILTER
This is used for
gathering the
dregs made
during washing.
WATER DRAIN HOSE
(without pump)
WASH TUB LID
Be sure to keep
the lid closed
during washing
and spinning.
EARTH WIRE
WASH TUB
PULSATOR
DRAIN FILTER
CONTROL LEG
CLEANING THE LINT FILTER
• If the dregs are piled up in the
lint filter after finishing the wash,
push down and
pull it out as
shown in the
figure.
• Wash the filter
net in water.
OVERFLOW FILTER
• Pull the upper side of the
overflow filter with your
fingers into the holes
in the direction of
arrow as shown
in the figure.
OVERFLOW FILTER
Pull the upper side of the
A
overflow filter with
two fingers inserted into
hole ‘A’ in the
direction of arrow
as shown in the figure.
CLEANING THE WASH TUB
First, fill water in the wash tub to ‘L’ level(
operating wash cycle for 1~2 minutes. •Close the wash tub lid.
CLEANING THE FILTER
• Pull the overflow filter out and take up
the filter by removing 3 screws as
shown in figure. Wash the filter and
washing tub.
CLEANING THE FILTER
• Push the strainer(filter) out and take
up the filter as shown in figure.
Wash the filter and washing tub.
DRAIN FILTER
In case of incomplete drain,
disassemble the drain filter with
screw driver(+), and remove
lints from the filter as shown
in the filter as shown in
the figure.
HOW TO CLEAN THE FILTER
(In case drain pump)
1. Place a rag under the washer filter
not to wet the floor.
2. Rotate the filter counterclockwise
and pull out the filter.
3. Remove dirts and
rotate the filter
clockwise until it
locks in position.
, then drain water from the wash tub simultaneously with
2
WASHING PROCEDURE
A-type : SWT90C1(P)/SWT90C2(P)/WT10S0(P)/WT10S1(P)/WT10S2(P)
TO WASH (A-type)
TO WASH (B-type)
1. Before starting to wash, proceed as follows,
Connect the water supply hose and open
the water tap.
• Lay the drain hose down toward
a sinkhole. (In case no drain pump)
• Place the drain hose in sink or bath.
(In case no drain pump)
• Connect the power cord to the power
supply outlet.
2. Set the CYCLE SELECTOR KNOB to
“WASH.RINSE”.(in case drain pump WASH)
Wash/Rinse
B-type : SW-903(P)
TO SPIN DRY
1. Before starting to wash, proceed as follows,
Connect the water supply hose and open
the water tap.
• Lay the drain hose down toward
a sinkhole. (In case no drain pump)
• Place the drain hose in sink or bath.
(In case no drain pump)
• Connect the power cord to the power
supply outlet.
Delicate
(LITE)
CYCLE SELECTOR
Drain
CYCLE SELECTOR
3. Set the WTER SELECTOR
KNOB to the desired mode.
Spin
Wash
WATER SELECTOR
4. Set the WASH SELECTOR
KNOB to the desired mode.
3. Close the spin
dryer lid.
WASH
DRAIN
DRAIN SELECTOR
4. Fill water in the wash tub
and add the detergent.
6. Set the WASH TIMER
1-15 minutes.
6. Load laundry in the
wash tub and fill water
to proper water level.
7. Set the WASH TIMER
1-15 minutes.
3. Press the
DRAIN SELECTOR KNOB
to ‘WASH’.
4. Set the SPIN DRY
TIMER 1-5 minutes.
3
12
6
0
15
3
6
9
WASH TIMER
WASH
DRAIN SELECTOR
8. After washing, set the CYCLE
SELECTOR KNOB to
'DRAIN' for drain.
9
WASH TIMER
3
2
3
12
15
1
SPIN DRY TIMER
7. After washing Press the
DRAIN SELECTOR KNOB to DRAIN
‘DRAIN’ for drain.
0
0
5
4
5. Load laundry in the
wash tub and fill water
to proper water level.
5. Fill water in the wash tub
and add the detergent.
safty cover
Heavy
WASH CONTROL
Drain Rinse
2. Be sure to replace the safety
cover and close the
inner lid
inner lid.
Normal
2. Select the WASH
CONTROL KNOB
for desired mode.
Wash
1. Transfer the clothes into the
spin basket and arrange the
clothes evenly.
ADDITIONAL RINSE
OVER FLOW RINSE (A-type)
TO RINSING (A-type)
1. Set the cycle selector KNOB to
‘WASH.RINSE’.
(In the case of drain
pump ‘WASH’)
Wash
Drain
CYCLE SELECTOR
2. Supply the proper amount of water
so as not to delete one space overflow
the top of the washing tub.
3. Set the WASH TIMER to
2~3 minutes.
15
3
12
6
9
WASH TIMER
4. Drain the water.
Set the delete one space cycle
selector KNOB to ‘DRAIN’.
TO RINSING (B-type)
WASH
DRAIN
DRAIN SELECTOR
0
15
3
12
3. Set the WASH TIMER
2~3 minutes.
5. Repeat this cycle until drain
water is clean. (2~3 cycles)
0
2. Set the WASH TIMER
6~8 minutes.
3
12
6
9
WASH TIMER
WASH TIMER
WASH
1 After rinsing you can select this
course for more effective rinse
(Don't just select this course
for rinse.) Load the laundry
evenly into the spin basket.
2 Set the WATER SELECTOR
KNOB to SPIN and
CYCLE SELECTOR Wash Spin
KNOB to ‘DRAIN’.
WATER SELECTOR
0
3. As soon as the
WASH TIMER
shuts off, turn off
the water tap.
15
3
12
6
9
3 Supply water for about 1 minute.
Adjust the water flow to prevent
overflow from the wash tub.
WASH TIMER
4 After completing the water supply,
cover the laundry with
inner lid
safety cover and close safety
cover
the inner lid.
1. Keep supplying
water(adjust water
pressure to ensure
that the amount of
water supplied
does not exceed the amount
of water drained.)
2. Set the WASH TIMER
6~8 minutes.
5 Close the spin dryer lid.
6 Set the SPIN DRY
TIMER 2~3 minutes.
0
15
3
12
6
9
WASH TIMER
3
12
6
9
WASH TIMER
DRAIN
4. Press the DRAIN SELECTOR
KNOB to ‘DRAIN’.
4
2
3
0
DRAIN SELECTOR
1
SPIN DRY TIMER
15
3. As soon as the
WASH TIMER
shuts off, turn off
the water tap.
0
5
4
6
9
DRAIN
4. Drain the water.
Set the DRAIN SELECTOR
KNOB to ‘DRAIN’.
CYCLE SELECTOR
4. Set the CYCLE
SELECTOR KNOB
to ‘DRAIN’.
OVER FLOW RINSE (B-type)
5. Repeat this cycle until drain
water is clean. (2~3 cycles)
2. Supply the proper amount
of water so as not to
delete one space overflow
the top of the washing tub
and put the laundry
into the washing tub.
Drain
15
0
1. Press the DRAIN SELECTOR
KNOB to ‘WASH’.
Wash
Drain Rinse
Drain Rinse
CYCLE SELECTOR
1. Keep supplying
water(adjust water
pressure to ensure
that the amount of CYCLE SELECTOR
water supplied
does not exceed the amount
of water drained.)
Wash/Rinse
Wash/Rinse
WASH
DRAIN SELECTOR
INSTALLATION
LAUNDRY GUIDE
LOCATION
Install the drain hose
about 70~80cm above
the ground for pump model.
CONNECTING THE DRAIN HOSE
After attaching the connector ring(a), insert the
drain hose(b) in the draining direction.
a
b
MOUNTING THE LEGS
Lay down the washer with its back facing
downward. Insert four legs into the leg mounting
sections of the base corners ofClaw
the main body.
Square
Insert the claw of the
hole
leg with the square
2
1
hole of the leg
mounting section,
and push the leg in
the arrow direction Leg
Bottom face of
as shown in the
main body
figure until it clicks.
WASHING TIME
Water Level
Low
Middle
High
Sgurts (Synthetics)
22 Pieces 29 Pieces 35 Pieces
Under Shirts (Cotton)
38 Pieces 48 Pieces 58 Pieces
Workign clothes (Cotton) 16 Pieces 20 Pieces 25 Pieces
CONNECTING THE DRAIN HOSE
1. Before connecting the drain hose, remove
the cover (a) from the drain hole.
2. After pressing the joint ring (b), insert the
drain hose(c) to drain direction.
(a)
(C)
(C)
(b)
(b)
CHANGING THE POSITION OF THE
DRAIN HOSE
Before attempting to change the position of the
drain hose, disconnect the plug from the outlet.
1. Route the drain hose inside the machine.
2.Take out the drain hose from the opposite hole
and insert the drain hose into the hose holder.
2
1
Hose holder
5
SPIN DRY TIME
TIME
TYPE OF FABRIC
1 min.
1~2 min.
3~5 min.
5 min.
Thin (synthetic fiber)
wool
cotton
thick (cotton)
DETERGENT
(In case of pump
drained washer)
70~80cm
Leave some space of
at least 15cm between the washing machine
and the wall.
Place the washing machine on a sturdy flat
surface.
If the washing machine is placed on an uneven
or weak surface, noise or vibration may occur.
(Allowable is 2˚)
Never install the washing machine near water.
Do not place the washing machine in steamy room or
where the washing machine is directly exposed to
rain. Moisture may damage electrical insulation
and cause an electrical shock to occur.
Avoid direct sunlight or heating devices.
As plastic and electrical components are
affected by direct heat, never place the washing
machine near heaters, boilers, etc., or under direct
sunlight.
WATER
The amount of detergent AMOUNT OF
LEVEL
DETERGENT
is average. Follow the
Low
(44l)
44g
instruction printed on the
package for amount of
56g
Medium (56l)
detergent. Choose the
67g
High (67l)
amount of detergent
according to the fabric type.
DETERGENT
In case the water level is at “High”,
amount of water is 42l
.
-H-
Follow the directions printed on the package
for amount of detergent. Choose the amount of
detergent depending on the fabric type and
water level.
MAINTENANCE
TO LOAD THE LAUNDRY INTO
THE SPIN BASKET.
Press the laundry evenly and put the safety
cover into the spin basket as shown in the
figure.
TROUBLE SHOOTING
TROUBLE
The washing
machine does
not work.
CHECK POINT
Check that the power cord is
properly connected to a power
outlet. Is there a power failure?
Is the machine overloaded?
Clothes do
not move freely.
TO RETRIEVE THE CLOTHING THAT HAS
FALLEN BETWEEN THE BASKET AND TUB.
For safety reason, pull the power supply plug out
of the socket.
1. Unscrew the spin dryer hatch.
2. The spin dryer hatch is
fixed to the brim by the
concave and convex
parts at two places.
Expand the concave and
convex parts,and pull up
the spin dryer hatch to
remove it.
3. Retrieve the clothing.
4. Close the spin dryer hatch. Push the hatch
firmly until the catch at the front is securely
attached.
Incomplete
spinning
Is the laundry arranged
evenly?
Incomplete
draining
Is the filter clogged with lint?
The spin dryer
basket will not
run.
AFTER OPERATION
1. Remove the power cord from the outlet.
2. Take out the laundry.
3. Close the water tap and disconnect the water
supply hose.
4. Clean the washing machine.
- Periodical cleaning will extend the life of your
washing machine.
- Do not spray the unit water or use tinner, benzene,
alcohol etc, for cleaning it.
Is the spin dryer lid closed
completely?
Are laundry items (socks, etc.) falling
out of the spin dryer basket and
clinging to the axle?
• See “To retrieve...”on page 6.
CLEANING THE WASHING MACHINE
Wipe off stains on the cabinet and operation pane
with a soft cloth. Neither use benzene, thinner,
cleanser, or wax, nor scrub the washing machine
with a brush. Painted surfaces or plastic parts will
be damaged.
6