IP Link® Device Interface
Communication Sheet
epsn_1_3458_3.pke
Revision: 1/12/2012
This document provides additional assistance with wiring your Extron IP Link enabled product to your device.
Different components may require a different wiring scheme than those listed below.
For complete operating instructions, refer to the user’s manual for the specific Extron IP Link enabled product or
the controlled device manufacturer supplied documentation.
Device Specifications:
Device Type:
Manufacturer:
Firmware Version:
Model(s):
Video Projector
Epson
1.00
PowerLite 85, PowerLite 825, PowerLite 826w, PowerLite 826w+, PowerLite 84+
Version History:
Driver
Version
Date
IP Link
Compiler
GC
Version
Notes
3
12/27/2011
1.5.1
3.3.1
Added model PowerLite 84+
2
2/10/11
1.4.0
3.0.4
Added model PowerLite 826W+ and Auto Image.
1
6/17/09
1.3.11.1
2.5.1
Initial Extron Certified version. Tested on PowerLite 85 firmware
version 1.00
Driver Notes:
Input Status may take up to 5 seconds to refresh after sending command
Page 1 of 5
IP Link® Device Interface
Communication Sheet
epsn_1_3458_3.pke
Revision: 1/12/2012
Control Commands & States:
Aspect Ratio*
Normal**
Auto Image
Execute
AV Mute
On
Off
Closed Caption
Off
CC1
Freeze
On
Off
Input
Computer1 RGB
Computer1 (YPbPr)
Computer2 RGB
Computer2 (YPbPr)
Video
S-Video
LAN
USB A
USB B
Lamp Mode
High
Low
Power Control
On
Off
Volume (Discrete)
0 to 20 in steps of 1
Volume (Step)
Up
4:3
Down
* Status will clear when input is USB.
** Only for Computer RGB mode
Page 2 of 5
16:9
CC2
IP Link® Device Interface
Communication Sheet
epsn_1_3458_3.pke
Revision: 1/12/2012
Status Available:
Aspect Ratio
Normal
4:3
AV Mute
On
Off
Closed Caption
Off
CC1
Connection Status
Connected
Disconnected
Device Status
Normal
Status Unavailable
Fan Error
Error
Lamp Cover Error
Lamp Error
High Temperature
Filter Error
EDL Capacitor
Disconnected
System Error
Low Air Flow Error
Power Error
Air Flow Error
Lamp Failure
Freeze
On
Off
Input
Computer1 RGB
Computer1 (YPbPr)
Computer2 RGB
Computer2 (YPbPr)
Video
S-Video
LAN
USB A
USB B
Lamp Mode
High
Low
Lamp Usage
Hours
Power Control
On
Off
Power Status
On
Off
Status Unavailable
Cooling Down
Volume (Discrete)
0 to 20 in steps of 1
Page 3 of 5
16:9
CC2
Warming Up
IP Link® Device Interface
Communication Sheet
epsn_1_3458_3.pke
Revision: 1/12/2012
MLC60 Series Supported Commands:
Aspect Ratio
Normal
4:3
Auto Image
Execute
AV Mute
On
Off
Closed Caption
Off
CC1
Freeze
On
Off
Input
Computer1 RGB
Computer1 (YPbPr)
Computer2 RGB
Computer2 (YPbPr)
Video
S-Video
LAN
USB A
USB B
Lamp Mode
High
Low
Power Control
On
Off
Volume (Discrete)
0 to 20 in steps of 1
Volume (Step)
Up
Down
Page 4 of 5
16:9
CC2
epsn_1_3458_3.pke
IP Link® Device Interface
Communication Sheet
Revision: 1/12/2012
Cable and Adapter Requirements:
F/F RS-232 Null Modem Serial Cable
Notes for the Device:
Serial communication:
Port Type: RS-232
Baud Rate: 9600
Data Bits: 8
Parity: None
Stop Bits: 1
Flow Control: None
Pin Assignments Diagram:
Note: Captive screw connector may also be used as a serial connection.
General Notes:
Page 5 of 5