Epson 7600 - EMP XGA LCD Projector Specifications

EPSON PowerLite 5600p and 7600p Projectors
Projector Specifications
control panel
status lights
speaker
General
front infrared
sensor
adjustable
foot
Type of display
Poly-silicon Thin Film Transistor (TFT)
Size of liquid
crystal panels
Diagonal: 1.3 inches (33.6 mm)
Lens
F=1.7 to 2.3, f=49 to 63 mm
Resolution
1024 × 768 pixels (PowerLite 7600p)
800 × 600 (PowerLite 5600p)
Color reproduction 24 bit, 16.8 million colors
handle
foot adjust lever
focus ring
zoom ring
Brightness
2200 lumens (ANSI)
Contrast ratio
400 : 1 (PowerLite 7600p)
300 : 1 (PowerLite 5600p)
Image size
22 to 300 inches
Projection distance 3.6 to 47.9 feet (1.1 to 14.6 meters)
Projection methods Front, rear, upside-down (ceiling mount)
Internal speaker
system
two 3-watt stereo speakers
Optical aspect ratio 4 : 3 (horizontal : vertical)
connector panel
(see below)
rear infrared
sensor
VGA (video in) connector
VGA / DVI
switch
S-Video
connector
36 dB
Type
UHE (Ultra High Efficiency)
Power
consumption
200 W
Lamp life
About 1500 hours
Part number
ELPLP12
DVI connector
Remote Control
Computer 1
Range
32.8 feet (10 meters)
Batteries
Alkaline AA (2)
Analog Digital
Computer 2 /
Component Video
Mouse Compatibility
Audio 1
connector
S-Video
L-Audio2-R
Audio 1
Audio Out
Supports PS/2, USB, serial, ADB (optional cable required for
serial and ADB)
Audio out
connector
Remote IR Receiver
Remote
audio
connectors
for video
sources and
Computer 2
Noise level
Projection Lamp
Computer 2/
Component
Video connector
Video
1 : 1.3
Keystone correction
angle
± 30° maximum
A/C power inlet
composite
(RCA)
video
connector
Zoom ratio
Control (RS-232C)
optional remote
receiver
connector
Supports EPSON Remote IR Receiver, 10-foot cable (typical
use for rear screen projection)
Mouse
Mouse connector
(for Computer 1)
serial connector for computer
running EMP Link V software
1/01
EPSON PowerLite 5600p and 7600p Projectors - 3
EPSON PowerLite 5600p and 7600p Projectors
Dimensions
.
Height
6.1 inches (156 mm)
Width
11 inches (280 mm)
Depth
15.9 inches (403 mm)
Weight
14.9 lb (6.8 kg)
Mode
Refresh Rate (Hz)
Resolution
VGACGA
70
640 × 400
VGAEGA
70
640 × 350
VGA60
59.94
640 × 480
VGA72
72.809
640 × 480
Electrical
VGA75
75
640 × 480
Rated frequency
50 to 60 Hz
VGA85
85.008
640 × 480
Power supply
100 to 120 VAC, 3.4 A
200 to 240 VAC, 1.7A
NEC400
56.65
640 × 400
SVGA56
56.25
800 × 600
SVGA60
60.317
800 × 600
SVGA72
72.188
800 × 600
SVGA75
75
800 × 600
Environmental
SVGA85
85.061
800 × 600
Temperature
XGA43i
86.958
1024 × 768
XGA60
60.004
1024 × 768
Storage: 14 to 140° F (–10 to 60° C),
non-condensing
XGA70
70.069
1024 × 768
XGA75
75.029
1024 × 768
Operating: 20 to 80% RH,
non-condensing
XGA85
84.997
1024 × 768
SXGA1—70
70.012
Storage: 10 to 90% RH,
non-condensing
1152 × 864
SXGA1—75
75
1152 × 864
SXGA1—85
84.999
1152 × 864
1280 × 960
Power
consumption
Humidity
Operating: 285 W
Standby: 9 W
Operating: 41 to 104° F (5 to 40° C),
non-condensing
Safety
United States
Canada
CE Marking
SXGA2—60
60
FCC Part 15B Class B
UL1950 Rev. 3
SXGA2—75
75
1280 × 960
SXGA2—85
85.002
DOC ICES003 Class B
CSA C22.2 No. 950 Rev. 3
1280 × 960
SXGA3—43i
86.871
1280 × 1024
Directive 89/336/EEC, 92/31/EEC
EN 60950
SXGA3—60
60.02
1280 × 1024
SXGA3—75
75.025
1280 × 1024
SXGA3—85
85.024
1280 × 1024
UXGA48i
96.08
1600 × 1200
UXGA60
60
1600 × 1200
UXGA65
65
1600 × 1200
UXGA70
70
1600 × 1200
UXGA75
75
1600 × 1200
UXGA80
80
1600 × 1200
UXGA85
85
1600 × 1200
MACLC13
66.62
640 × 480
MAC II 13
66.67
640 × 480
MAC16
74.55
832 × 624
Compatible Video Formats
The projector supports the following international video
standards: NTSC, HDTV, PAL, and SECAM, as well as the
monitor display formats listed below.
To project images output from a computer, the computer’s
video card must be set at a refresh rate (vertical frequency)
that’s compatible with the projector; see the following table
for compatible formats. Some images are automatically resized
to display in the projector’s native format (XGA for the
PowerLite 7600p, SVGA for the PowerLite 5600p). The
frequencies of some computers may not allow images to
display correctly; see your computer’s documentation for
details.
4 - EPSON PowerLite 5600p and 7600p Projectors
1/01
MAC19—60
59.28
1024 × 768
MAC19
74.93
1024 × 768
MAC21
75.062
1152 × 870
EPSON PowerLite 5600p and 7600p Projectors
Mode
Refresh Rate (Hz)
Resolution
HDTV480P (ANSI/
SMPTE)
59.94
720 × 483
HDTV480P
(ATSC)
59.94
704 × 480
HDTV480I (ANSI/
SMPTE)
59.94
720 × 487
HDTV480I (ANSI/
SMPTE)
59.94
1920 × 1080
HDTV480I
(ATSC)
59.94
704 × 480
HDTV720P
(SMPTE)
59.94
1280 × 720
HDTV1080I (ANSI/
SMPTE)
59.94
1920 × 1080
HDTV1080P (ANSI/
SMPTE)
59.94
Positioning the Projector
Follow these guidelines to get the best results when projecting:
❏ Place the projector on a sturdy, level surface, between
3.6 and 48 feet from the screen.
❏ Make sure there is plenty of space for ventilation around and
under the projector.
❏ Make sure the projector is within 6 feet of a grounded
electrical outlet or extension cord and within 5 feet of the
image source.
❏ Face the projector squarely toward the screen. Otherwise,
your image won’t be square.
Note: It’s easier to position the projector when the screen is
directly in front of the room. If the screen is placed diagonally in a
corner, it’s much more difficult to aim the projector squarely at
the screen and get a non-distorted image.
1920 × 1080
NTSC (SVGA)
60
800 × 438
NTSC (XGA)
60
1024 × 438
PAL (SVGA)
50
800 × 512
PAL (XGA)
50
1024 × 512
SECAM (SVGA)
50
800 × 512
SECAM (XGA)
50
1024 × 512
If you place the projector below the level of the screen, you’ll
have to tilt it up by extending the feet as shown. Tilting the
projector upward causes the image to lose its square shape, but
you can correct the distortion by pressing the Keystone
button as described on page 8.
Computer Video Port Pin Assignments
The Computer 1 analog port is a female video RGB, 15-pin
micro-D-style connector. Here are the pin assignments:
Pin #
Computer 1 port (analog)
1
Red video
2
Green video
3
Blue video
4
Monitor (ID bit 2)
5
GND
6
Red video GND
7
Green video GND
8
Blue video GND
9
+5V
10
Synchronous GND
11
Monitor (ID bit 0)
12
SDA
13
Horizontal sync
14
Vertical sync
15
Reserved
ideal
height
If you place the projector level with the bottom of the screen,
the image will be square and you won’t have to adjust it. If
you place the projector higher than the bottom of the screen,
the image will still be square, but you won’t be able to fill the
whole screen with the image.
1/01
EPSON PowerLite 5600p and 7600p Projectors - 5
EPSON PowerLite 5600p and 7600p Projectors
Image Size and Projection Distance
The projector can be installed for three different viewing
setups: front projection, ceiling mounting, or rear projection
onto a semi-transparent screen, as shown:
Use the tables below to estimate how far to place the projector
from the screen. Since the size of the image can be changed by
rotating the zoom ring, a range of distance is given for each
screen size.
Note that if you tilt the projector upward by extending the
feet or use electronic keystone correction, your image size may
vary.
Standard lens
front projection
ceiling mounting
Diagonal screen
size
Distance
30 inches
3.6 to 4.6 feet (1.1 to 1.4 meters)
60 inches
7.2 to 9.5 feet (2.2 to 2.9 meters)
100 inches
12.1 to 15.7 feet (3.7 to 4.8 meters)
200 inches
24.9 to 31.8 feet (7.6 to 9.7 meters)
300 inches
36.4 to 47.9 feet (11.1 to 14.6 meters)
Long throw zoom lens (ELPAL01)
rear projection
To project from overhead, you’ll need to select Ceiling in the
projector’s Advanced menu. To project from the rear, select
Rear Proj.
If you’re ceiling-mounting the projector and you place it
above screen level, you’ll have to tilt it down to position the
image on-screen. This causes the image to lose its square
shape. You can then correct the distortion by using the
Keystone function in the projector’s menu system or by using
the Keystone button on the projector’s control panel.
Distance
30 inches
4.23 to 5.71 feet (1.29 to 1.74 meters)
60 inches
9.06 to 11.94 feet (2.76 to 3.64 meters)
100 inches
15.45 to 20.28 feet (4.71 to 6.18 meters)
200 inches
31.46 to 41.08 feet (9.59 to 12.52 meters)
300 inches
47.44 to 61.88 feet (14.46 to 18.86 meters)
Wide angle lens (ELPAW01)
If you place the projector’s lens so it’s level with the top of the
screen, the image will be square and you won’t have to adjust
it. If you place the lens lower than the top of the screen, you’ll
have to tilt the projector upward if you want to fill the whole
screen with the image.
6 - EPSON PowerLite 5600p and 7600p Projectors
Diagonal screen
size
1/01
Diagonal screen
size
Distance
30 inches
2.49 to 3.35 feet (0.76 to 1.02 meters)
60 inches
5.25 to 6.96 feet (1.60 to 2.12 meters)
100 inches
8.96 to 11.8 feet (2.73 to 3.59 meters)
200 inches
18.1 to 23.8 feet (5.53 to 7.26 meters)
300 inches
27.3 to 35.8 feet (8.31 to 10.90 meters)
EPSON PowerLite 5600p and 7600p Projectors
2. Click the Arrange icon and drag one monitor icon on top of
the other.
Displaying an Image
Click here
Once the projector is connected to your computer or video
source and plugged in, press the red Power button on top of
the projector to turn it on. The power light flashes green as the
projector warms up, and the projection lamp comes on in
about 30 seconds. The power light stays green, and you may
see a blue screen with the message No Signal displayed. This is
normal.
Do one of the following:
❏ Turn on or restart your computer. In a few moments, you
should see your computer display projected.
Drag one monitor
icon on top of
the other
(Windows only: If you see a New Hardware Found message
saying that it has found a plug-and-play monitor, click
Cancel.)
❏ If you’re projecting a video, press the Play button on your
video source.
If the Arrange option isn’t available, you may need to select
one of the Simulscan resolution settings:
If a projected image fails to appear, see the next section for
help.
1. Click the Monitor icon.
Click here
What To Do If You See a Blank Screen
If you see a blank screen or a blue screen with the message
No Signal after turning on your computer or video source, do
one of the following:
❏ Make sure the cables are connected correctly, as described in
the User’s Guide.
Select a
Simulscan
resolution
❏ Make sure the power light is green and not flashing and the
lens cover is off.
❏ Try restarting your computer.
2. Select a Simulscan resolution as shown. Allow a few seconds
for the projector to sync up after making the selection.
❏ If you’ve connected more than one computer and/or video
source, you may need to press the Computer or Video
button on top of the projector to select the correct source.
Allow a few seconds for the projector to sync up after
pressing the button.
If you’re using a PC laptop:
❏ Hold down the the Fn key and press the function key that
lets you display on an external monitor. It’s often labelled
with an icon such as
but it may also be labelled CRT/
LCD. Allow a few seconds for the projector to sync up after
pressing it.
If you’re using a PowerBook:
You may need to set up your system to display on the
projector screen as well as the LCD screen. Follow these steps:
On most systems, the
key lets you toggle between the
LCD screen and the projector, or display on both at the
same time. Check your laptop’s manual or online help for
details.
1. From the Apple menu, select Control Panels, then click
Monitors and Sound.
❏ Depending on your computer’s video card, you might need
to use the Display utility in the Control Panel to make sure
that both the LCD screen and external monitor port are
enabled. See your computer’s documentation or online help
for details.
1/01
EPSON PowerLite 5600p and 7600p Projectors - 7
EPSON PowerLite 5600p and 7600p Projectors
Resizing the Image
Projector Status Lights
Some computer images need to be resized to display in the
projector’s native format. If only part of your computer image
is displayed, you can correct it with the Resize button.
The lights on top of the projector indicate the projector’s
operating status.
❏ Press the Resize button on the control panel. The screen
image is automatically compressed.
Power
❏ Continue pressing the Resize button to pan around the
screen in the original resolution.
Computer
A/V mute
If you’re projecting from video equipment, pressing the
Resize button switches the aspect ratio between 4:3 and 16:9.
If you’ve zoomed in on your image (using the E-Zoom button
on the remote), you can press the Resize button to restore the
original display size.
power light
lamp light
Resize
temperature light
Adjusting the Image Shape
If the projected image isn’t square or has a “keystone” shape,
do one or more of the following:
❏ If your image looks like
or
, you’ve placed the
projector off to one side of the screen, at an angle. Move it
directly in front of the center of the screen, facing the screen
squarely.
Light
Status
Description and action
Does not
come on
Make sure the power cord is securely
connected at both the power outlet and
projector.
Green
The projector is operating normally.
Flashing
green
The projector is warming up. Wait for the
image to appear.
Orange
The projector is in sleep mode. You can
unplug it to turn it off, or press the Power
button to turn it on.
Flashing
orange
The lamp is cooling down. Wait for the
indicator light to stop flashing before
unplugging the projector or turning it back on.
Flashing red
Power is cut off because of an internal
problem. Disconnect the power cord and
contact EPSON for help.
❏ Press the Video button to switch between a standard
composite video source and an S-Video source.
Flashing
orange
The lamp is almost burned out. This is a good
time to replace it.
❏ Press the Comp1 button to select your first computer.
Flashing red
The lamp is burned out and must be replaced.
If you’ve just replaced the lamp, make sure the
cover is fastened securely.
❏ If your image looks like
or
, press the + or —
side of the Keystone button to correct the shape of the
image. After correction, your image will be slightly smaller.
You can also perform electronic keystone correction using the
projector’s Setting menu.
Switching Between Picture Sources
If your projector is connected to more than one computer
and/or video source, you can use the buttons on the control
panel (or remote control) to switch between the different
sources.
On the control panel, press the Computer button to switch
between the computer sources and press the Video button to
switch between standard (composite) video, S-Video, and
component video (BNC).
On the remote control:
❏ Press the Comp2/YCbCr button to select your second
computer or a component video source.
After you select a source, the screen goes dark for a moment
before the image appears.
8 - EPSON PowerLite 5600p and 7600p Projectors
1/01
EPSON PowerLite 5600p and 7600p Projectors
Light
Status
Description and action
Button
Function
Flashing
orange
The projector is getting too hot. Turn it off and
let it cool. Make sure the temperature
surrounding the projector does not exceed
104° F and there is plenty of space around
and under the projector for ventilation. Clean
the air filter if necessary.
Esc
Stops the current function. Pressing Esc while viewing
a menu or the online help displays the previous
screen or menu.
Sync +
Sync –
Synchronizes the computer’s graphic signal. Use
these buttons to adjust a fuzzy-looking image that
contains a lot of fine detail. Allows selection of a menu
or menu options if the menu screen is displayed.
Tracking –
Tracking +
Matches the projector’s internal clock to computer
graphic signals. Use these buttons to eliminate
vertical stripes or bands from an image that contains a
lot of fine detail. Also changes settings during menu
operations.
Enter
Selects a menu option or the next menu/help screen.
Pressing Enter when no menu or help screen is
displayed optimizes the computer image.
Red
The projector has overheated and turned off
automatically. Let it cool for a few minutes,
then turn it back on. Make sure there is plenty
of space around and under the projector for
ventilation. Clean or replace the air filter, as
needed. If it continues to overheat, there may
be a problem with the cooling fan or internal
circuits; contact EPSON for help.
Flashing red
There is a problem with the cooling fan or
temperature sensor. Turn off the projector and
unplug it. Contact EPSON for help.
Shift
Pressing the shift and Keystone buttons at the same
time increases or decreases the sound volume.
– Keystone +
Use after tilting the projector (extending its feet) to
square up the image. Corrects up to a ±30° tilt.
– Volume +
Adjusts the volume when pressed with the Shift
button.
Using the Control Panel
Power
Computer Video
Menu
Sync
Esc
Help
Using the Remote Control
A/V mute
Tracking
Tracking
The remote control uses a line-of-sight infrared signal. It lets
you access the projector’s features from anywhere in the
room—up to 32 feet away. (This distance may be shorter if
the remote control batteries are low.) If you have connected
the mouse cable, you can also use the remote control as a
wireless mouse.
Keystone
Resize
Shift
Volume
Sync
The following table summarizes the functions on the control
panel.
Button
Function
Power
Starts or stops projection.
Help
Displays the online help menu.
Computer
Switches between Computer 1 and Computer 2.
A/V mute
Turns off the audio and video. (In the menu system,
you can set whether the screen appears black or blue,
or displays a user logo.)
Resize
Resizes non-standard computer video formats so they
appear correctly on screen. Switches the aspect ratio
between 4:3 and 16:9 when video images are being
projected.
Video
Switches between standard (composite) video,
S-Video, and component video (BNC).
Menu
Displays or hides the menu screen.
The projector may not respond to remote control commands
in these conditions:
❏ The remote control is not turned on (using the switch on its
side)
❏ You are too far away or not within 30° to the left or right of
the front or rear sensor or 15° above or below
❏ Batteries are weak
❏ Ambient light is too bright
❏ A fluorescent light is shining into the infrared receiver
❏ A strong light source (such as direct sunlight) shines into the
infrared receiver
❏ Other equipment emitting infrared energy is present (such as
a radiant room heater)
1/01
EPSON PowerLite 5600p and 7600p Projectors - 9
EPSON PowerLite 5600p and 7600p Projectors
This table summarizes the functions on the remote control.
The remote control buttons are shown in the following
illustrations.
signal output
Button
Function
Power
Starts or stops the projector.
Power
R/C on/off
Turns the remote control on or off.
on/off switch
Freeze
Keeps the current computer or video image on the
screen.
A/V mute
Turns off the audio and video, displaying the black,
blue, or user logo background.
E-Zoom
Changes the image size up to 4×. Pressing the right
side of the button enlarges the image, pressing the left
side reduces the image. To display a portion of an
enlarged image which is outside the display area,
press the Enter button and scroll the image to the
desired location.
Effects buttons
Display preprogrammed special drawing effects on the
screen. Additional effects can be selected through the
Effect menu or programmed using the EMP Link V
software.
Enter
(pointer button)
Use the Enter button to navigate the menus or use the
remote as a mouse pointer when the projector is
connected to the computer with the mouse cable.
When the image source is a computer, the Enter
button acts as a mouse left-click.
Light
Illuminates all buttons on the remote control
temporarily. If the buttons don’t light up, the batteries
may be weak.
Esc
Stops the current function. Pressing Esc while viewing
a menu or the online help displays the previous screen
or menu. When the image source is a computer, the
Esc button acts as a mouse right-click.
Menu
Displays or hides the menu.
Help
Help
Displays the online help menu.
Comp2/YCbCr
Comp1
Switches to the Computer 1 image.
Comp2/YCbCr
Switches to the Computer 2 or component video
source.
Video
Switches to the standard composite video or S-Video
source.
Auto
Optimizes the computer image.
Resize
Resizes SXGA and other video formats so they
appear correctly on the screen. Switches the aspect
ratio between 4:3 and 16:9 when video images are
being projected.
P in P
Displays a video or S-video image in a subscreen on
the main display. Use the Enter button to reposition
the Picture in Picture (P in P) screen, or the E-Zoom
button to enlarge or reduce the image. Changes made
to the P in P screen location and size are
automatically carried over to the next P in P session.
Freeze
A/V Mute
Power
Freeze
A/V Mute
E-Zoom
E-Zoom
3
4
5
1
2
Special effects
buttons (1-5)
R/C ON
OFF
Enter
Esc
light button
Enter (pointer) button
Esc button
Open the cover just below the Esc button to access these
remote control buttons:
Menu
Comp1
E@sy-MP
Video
Auto
Resize
P in P
Preset
Volume
10 - EPSON PowerLite 5600p and 7600p Projectors
1/01
EPSON PowerLite 5600p and 7600p Projectors
Button
Function
Preset
Saves and recalls up to five different session settings
(resolution, tracking, sync signal, and position). To
save the current session settings, press the Preset
button and it will be assigned the next available
number, 1 through 5. To recall a setting, press the
Preset button a second time and move to the desired
session number. To overwrite a saved setting, move
to the setting you want to replace and press Enter.
When the confirmation message displays, choose Yes
and press Enter.
– Volume +
Cleaning the Projector Case
Before you clean the projector case, turn off the projector and
unplug the power cord.
❏ To remove dirt or dust, wipe the case with a soft, dry, lintfree cloth.
❏ To remove stubborn dirt or stains, moisten a soft cloth with
water and a neutral detergent. Then wipe the case.
❏ Do not use alcohol, benzene, thinner, or other chemical
detergents. These can damage the case.
Adjusts the volume.
The five special effects buttons are preprogrammed with the
following functions.
Cleaning or Replacing the Air Filter
Clean the air filter at the bottom of the projector after every
100 hours of use. If it is not cleaned periodically, it can
become clogged with dust, preventing proper ventilation. This
can cause overheating and damage the projector.
Button
Function
1
Changes the mouse cursor to a pointer or cursor stamp
2
Lets you draw one or more boxes on the screen
Follow these steps:
3
Spotlights a section of the screen
4
Lets you place a vertical or horizontal bar on the screen to
highlight a part of your image
1. Turn off the projector, allow it to cool down, and unplug the
power cord.
5
Erases the drawing effects on the screen
2. Turn the projector on its side so that the handle is on top
and you can access the filter easily.
3. To clean the filter, EPSON recommends using a small
vacuum cleaner designed for computers and other office
equipment. If you don’t have one, gently clean the filter
using a very soft brush (such as an artist’s camel-hair brush).
Note: You can use the projector’s Effect menu to select different
options for each of the drawing tools.
Cleaning the Lens
Warning: Before you clean any part of the projector, turn it off
and unplug the power cord. Never open any cover on the
projector, except the lamp and filter covers. Dangerous electrical
voltages in the projector can injure you severely. Do not try to
service this product yourself, except as specifically explained in this
Product Information Guide. Refer all other servicing to
qualified service personnel.
Clean the lens whenever you notice dirt or dust on the surface.
❏ Use a canister of compressed air to remove dust.
❏ To remove dirt or smears on the lens, use lens cleaning
paper. If necessary, moisten a soft cloth with an alcoholbased cleaner and gently wipe the lens surface.
If the dirt is difficult to remove or if the filter is torn, replace
it. Contact your dealer or call EPSON at (800) 873-7766 in
the United States and Canada to obtain a new one.
Note: When you get a replacement lamp for your projector, a
new air filter is included. You should replace the filter when
you replace the lamp.
1/01
EPSON PowerLite 5600p and 7600p Projectors - 11
EPSON PowerLite 5600p and 7600p Projectors
Contact your dealer or call EPSON at (800) 873-7766 in the
United States and Canada for a replacement lamp. Request
part number ELPLP12.
4. If you need to replace the filter, make sure the projector is on
its side as shown (not turned upside down) to prevent dust
from falling inside. Then release the latch to remove the
filter.
Follow these steps to replace the lamp:
1. Turn off the projector and unplug the power cord.
2. Allow the projector to cool down for at least an hour (if it
has been on).
3. Use a screwdriver to loosen the screw on the lamp cover.
(You can’t remove the screw from the cover.)
When the screw is loose, slide off the lamp cover.
latch
5. To install the new filter, first insert the tabs, then press on
the latch until it clicks in place.
4. Use a screwdriver to loosen the two screws holding the lamp
in place. (You can’t remove these screws.)
5. Lift up the wire handle, as shown, and pull the lamp straight
out.
tabs
handle
Replacing the Lamp
6. Fully insert the new lamp.
The projection lamp typically lasts for about 1500 hours of
use. It is time to replace the lamp when:
❏ The projection image gets darker or starts to deteriorate.
❏ The lamp warning light
is flashing red or orange.
❏ The message LAMP REPLACE appears on the screen when
the projector lamp comes on (after about 1400 hours of use).
To maintain projector brightness and image quality, replace
the lamp as soon as possible.
Note: You can check to see how many hours the lamp has been
used through the About menu.
Caution: Do not touch the glass portion of the lamp assembly.
12 - EPSON PowerLite 5600p and 7600p Projectors
1/01
EPSON PowerLite 5600p and 7600p Projectors
You can purchase these accessories from your dealer or by
calling EPSON at (800) 873-7766; or visit the EPSON Store
at www.epson.com (U.S. sales only). In Canada, please call
(800) 873-7766 for dealer referral.
7. Once the lamp is fully inserted, tighten its screws.
8. Replace the lamp cover and tighten its screw securely. (The
projector won’t come on if the lamp cover is loose.)
9. Reset the lamp timer as described in the following section.
Resetting the Lamp Timer
Related Documentation
After you install a new lamp, you need to reset the timer so the
projector can keep track of how many hours it has been used.
Follow these steps:
1. Press the Help button and hold it down for at least 5
seconds. The Help menu will be displayed and then you will
see a menu asking if you want to reset the lamp ON time.
2. Use the left arrow button (control panel) or press left on the
Enter button (remote control) to select Yes.
3. Press Enter to reset the timer.
CPD-11582
EPSON PowerLite 5600p and 7600p
User’s Guide
CPD-11583
EPSON PowerLite 5600p and 7600p
Quick Setup Poster
Service Manual
TBD
Parts Price Lists
PL-EMP5600
PL-EMP7600
Optional Accessories
Product
Product number
Replacement lamp and air filter
ELPLP12
Long throw zoom lens
ELPAL01
Wide angle lens
ELPAW01
Customized carrying cases:
Samsonite® wheeled soft case
ATA molded hard shell case
ATA shipping case
ELPKS35
ELPKS38
ELPKS39
Ceiling mount
ELPMB34
Suspension adapter for ceiling mount
ELPMBAST
Kensington security lock
ELPSL01
Portable projection screens:
50-inch
60-inch
80-inch
ELPSC06
ELPSC07
ELPSC08
Wireless microphone and two satellite
speakers
ELPCUS1
Auxiliary audio system
ELPPAS1
Remote control receiver (plugs into projector
to extend range of remote control)
ELPST02
Remote control receiver kit (includes standard
receiver and clip-on receiver for attachment
directly to remote control)
ELPST04
Macintosh adapter set (includes monitor
adapter and desktop adapter)
ELPAP01
Component video cable (VGA to 3BNC)
ELPKC19
Digital video cables:
DVI to DVI, 10 feet (3 meters)
DVI to DFP, 10 feet (3 meters)
ELPKC20
ELPKC21
1/01
EPSON PowerLite 5600p and 7600p Projectors - 13