Westermo DR-260 User guide

DR-260
DR-260
DSL Router
LAN
SIM 1
SIM 2
3G/GPRS
PWR
0
1
2
3
WLAN
DTE
DSL
NET SIM DAT
SIGNAL
ISDN
D
OH
B1
B2
CD
DAT
PSTN
ADSL / ADSL2 / ADSL2+
Router
www.westermo.com
© Westermo Teleindustri AB
User Guide
6622-2231 29000448
Legal information
The contents of this document are provided “as is”. Except as required by applicable
law, no warranties of any kind, either express or implied, including, but not limited to,
the implied warranties of merchantability and fitness for a particular purpose, are made
in relation to the accuracy and reliability or contents of this document. Westermo
reserves the right to revise this document or withdraw it at any time without prior
notice.
Under no circumstances shall Westermo be responsible for any loss of data or income
or any special, incidental, and consequential or indirect damages howsoever caused.
More information about Westermo can be found at the following Internet address:
http://www.westermo.com
2
6622-2231 • 29000448
Safety
!
Before using this unit:
Read this manual completely and gather all information on the unit. Make sure
that you understand it fully. Check that your application does not exceed the safe
operating specifications for this unit.
Hazardous voltages may occur within this unit when connected to a power supply.
Prevent access to hazardous voltages by disconnecting the unit from its power
supply.
Prevent damage to internal electronics from electrostatic discharges (ESD) by discharging your body to a grounding point (e.g. use of wrist strap).
!
Before installation:
This unit should only be installed by qualified personnel.
This unit should be built-in to an apparatus cabinet, or similar, where access is
restricted to service personnel only.
The power supply wiring must be sufficiently fused, and if necessary it must be
possible to disconnect manually from the power supply. Ensure compliance to
national installation regulations.
This unit uses convection cooling. To avoid obstructing the airflow around the unit,
follow the spacing recommendations (see Installation section).
Care recommendations
Follow the care recommendations below to maintain full operation of unit and to fulfil
the warranty obligations.
This unit must not be operated with covers or lids removed.
Do not attempt to disassemble the unit. There are no user serviceable parts inside.
Do not drop, knock or shake the unit, rough handling beyond the specification may cause
damage to internal circuit boards.
Do not use harsh chemicals, cleaning solvents or strong detergents to clean the unit.
Do not paint the unit. Paint can clog the unit and prevent proper operation.
Do not expose the unit to any kind of liquids (rain, beverages, etc). The unit is not
waterproof.‑Keep the unit within the specified humidity levels.
Do not use or store the unit in dusty, dirty areas, connectors as well as other mechanical
part may be damaged.
If the unit is not working properly, contact the place of purchase, nearest Westermo distributor office or Westermo Tech support.
GSM specific safety
Please read and follow the guidelines listed below. The precautions must be observed
during all phases of the operation. Breaking these rules may be dangerous, illegal or affect
performance of the unit and/or invalidate the unit’s approval and/or warranty.
6622-2231 • 29000448
3
General
Remember to follow any special regulations and warnings in force in any area and never
use the unit whenever it’s forbidden to use it. Do not use the unit when it may cause
interference or danger. A wireless device exposed to interference above specified limits
could result in deteriorated performance.
Hospitals or other Medical environment
Do not use the unit in a medical environment such as health care facilities. Follow any
regulations or rules that instruct you to not use the unit.
Pacemakers
The Health Industry Manufacturers Association recommends that a minimum separation
of six (6”) inches be maintained between cellular wireless equipment and a pacemaker to avoid potential interference with the pacemaker. These recommendations are consistent with the independent research by and recommendations of‑Wireless Technology
Research.
Persons with pacemakers:
… Should ALWAYS keep the the unit and its antenna more than six inches from their
pacemaker when the unit is turned ON.
… If you have any reason to suspect that interference is taking place, turn your wireless
equipment OFF immediately.
Hearing Aids
Some digital wireless equipment may interfere with some hearing aids. In the event of
such interference, you may want to consult your service provider [or call the customer
service line to discuss alternatives.]
Other Medical Devices
If you use any other personal medical device, consult the manufacturer of your device to
determine if they are adequately shielded from external RF energy.‑Your physician may be
able to assist you in obtaining this information.
Turn the wireless equipment OFF in health care facilities when any regulations posted in
these areas instruct you to do so. Hospitals or health care facilities may be using equipment that could be sensitive to external RF energy.
Aircraft
Do not use the unit in an aircraft. The use of a wireless unit in an aircraft may be dangerous to the operation of the aircraft, disrupt the wireless network, and may be illegal.
Failure to observe these instructions may lead to suspension or denial of cellular services
to the offender, legal action, or both.
Vehicle
If the unit is incorrectly installed in a vehicular environment, the operation of the unit
could interfere with the vehicle electronics. Faulty installation and/or operation can constitute a safety hazard.
4
6622-2231 • 29000448
For Vehicles equipped with an airbag
An air bag inflates with great force. DO NOT place objects, including either installed or
portable wireless equipment, in the area over the air bag or in the air bag deployment
area. If in-vehicle wireless equipment is improperly installed and the air bag inflates, serious injury could result.
Blasting areas
Do not use the unit where blasting is in progress or in “blasting areas”. Observe restrictions and follow any regulation or rules.
Explosive atmospheres
Do not use the unit in any area with a potentially explosive atmosphere. Potentially explosive areas are often, but not always, clearly marked. They include fuelling areas such as petrol stations, below decks on boats, fuel or chemical
transfer or storage facilities, and areas where the air contains chemicals or particles, such
as grain, dust, or metal powder.
RF energy
The DR-260/3G is a low power radio transmitter and receiver. When it is ON, it receives
and also sends out radio frequency (RF) signals. Most modern electronic equipment is shielded from RF signals. However, certain electronic equipment may not be shielded against the RF signals from the wireless unit. All
radio-transmitting devices send signals, which may cause interference in different electronic devices. To avoid interference, place the units antenna a sufficiently long distance
from other electronics.
Critical applications
Cellular units operate using radio signals and cellular networks cannot be guaranteed to
connect in all conditions. Therefore you should never rely solely on a wireless device for
essential communications, for example medical emergencies.
Backup copies
Remember to make backup copies of all important data, for example PIN/PUK codes,
contents of SIM card etc.
Antenna care
Use only the supplied or an approved replacement antenna. Unauthorized antennas, modifications, or attachments could damage the unit and may violate current regulations.
Do not touch the antenna unnecessarily when the unit is in use. Contact with the antenna affects call quality and may cause the unit to operate at a higher power level than
otherwise needed.
Maintenance
No maintenance is required, as long as the unit is used as intended within the specified
conditions.
6622-2231 • 29000448
5
Agency approvals and standards compliance
Type
Approval / Compliance
EN 55024, EN 55024 A1, EN 55024 A2, Electromagnetic compatibility Immunity IT equipment
EMC
EN 55022, EN 55022 A1, Information technology equipment. Radio disturbance characteristics. Limits and methods of measurement
FCC part 15 Class B
Safety
IEC / EN 60950-1, IT equipment
Article 3.1a
Article 3.1b
R&TTE
Article 3.2
EN 60950
Safety
EN 50385
EMF exposure
EN 301 489-1
ERM/EMC
EN 301 489-7
ERM/EMC GSM
EN 301 489-24
ERM/EMC 3G
EN 301 908-1
ERM 3G
EN 301 908-2
ERM 3G
EN 301 511
GSM
FCC Part 15.105 Notice:This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equip­ment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
… Reorient or relocate the receiving antenna
… Increase the separation between the equipment and receiver
… Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected
… Consult the dealer or an experienced radio/TV technician for help.
6
6622-2231 • 29000448
Declaration of Conformity
Westermo Teleindustri AB
Declaration of conformity
The manufacturer
Westermo Teleindustri AB
SE-640 40 Stora Sundby, Sweden
Herewith declares that the product(s)
Type of product
Cellular router
Model
DR-260A series
Art no
3622-0210, 3622-0220, 3622-0230
Cellular router
DR-260B series
3622-0240, 3622-0250, 3622-0260,
3622-0270, 3622-0280
is in conformity with the following EC directive(s).
No
Short name
1999/5/EC
Radio equipment and Telecommunications terminal equipment (R&TTE)
References of standards applied for this EC declaration of conformity.
No
EN 60950-1
EN 55022
Title
Information technology equipment - Safety -- General
requirements
Information technology equipment - Emission
EN 55024
Information technology equipment - Immunity
EN 61000-3-2
Electromagnetic compatibility (EMC): Limits - Limits for
harmonic current emissions
Electromagnetic compatibility (EMC) : Limits - Limitation of
voltage changes, voltage fluctuations and flicker in public lowvoltage supply systems.
Electromagnetic compatibility and Radio spectrum Matters
(ERM); ElectroMagnetic Compatibility (EMC) standard for radio
equipment and services: Specific conditions for mobile and
portable radio and ancillary equipment of digital cellular radio
telecommunications systems (GSM and DCS)
Electromagnetic compatibility and Radio spectrum Matters
(ERM); ElectroMagnetic Compatibility (EMC) standard for radio
equipment: Specific conditions for Broadband Data Transmission
Systems
Global System for Mobile communications (GSM); Harmonized
EN for mobile stations in the GSM 900 and GSM 1800 bands.
EN 61000-3-3
EN 301489-7
EN 301489-17
EN 301511
The last two digits of the year in which the CE marking was affixed:
Issue
2006
+A11:2009
2006
+A1:2007
1998
+A1:2001
+A2:2003
2006
1995
+A1:2001
+A2:2005
V1.3.1
V1.3.2
V9.0.2
11
Pierre Öberg
Technical Manager
25th January 2011
Postadress/Postal address
Tel.
Telefax
Postgiro
Bankgiro
Org.nr/
Corp. identity number
Registered office
S-640 40 Stora Sundby
Sweden
016-428000
Int+46 16428000
016-428001
Int+46 16428001
52 72 79-4
5671-5550
556361-2604
Eskilstuna
6622-2231 • 29000448
7
Type tests and environmental conditions
Phenomena
Test
Description
Test levels
ESD
EN 61000-4-2
Enclosure contact
± 4 kV
Enclosure air
± 8 kV
RF field AM modulated
EN 61000-4-3
Enclosure
3 V/m 80% AM (1 kHz), 80 – 1 000 MHz, 1
400 MHz – 2 000
Fast transient
EN 61000-4-4
Signal ports
± 0.5 kV
Power ports
± 1 kV
Telecom/Signal ports
± 0.5 kV line to earth
Surge
EN 61000-4-5
Power ports
± 2 kV line to earth, ± 2 kV line to line
RF conducted
EN 61000-4-6
Power ports
3V/m 80% AM (1 kHz), 0.15 – 80 MHz
Voltage dips and interruption
EN 61000-4-11
AC power ports
10 & 100 ms, interruption 10 ms, 30% reduction 100 ms, 60% reduction 5000 ms, >95% reduction +30% above & –20% below rated voltage
Radiated emission
EN 55022
Enclosure
Class B
FCC part 15
Conducted emission
Class B
EN 55022
AC power ports
Class A
FCC part 15
AC power ports
Class B
EN 55022
DC power ports
Class B
Operating DR-260
–20 to +70º Celsius –4 to +158º Fahrenheit
Operating DR-260 + 3G
–20 to +55º Celsius –4 to +131º Fahrenheit
Storage & Transport
–40 to +85º Celsius –40 to +185º Fahrenheit
Humidity
Operating
5 to 95% relative humidity
Altitude
Storage & Transport
Operating
5 to 95% relative humidity
2000 m / 70 kPa
Temperature
Reliability prediction
(MTBF)
Bellcore RQGR at 40°C
131 400 hours
Enclosure
Pressed steel
Dimension W x H x D
DR-260
239 x 40 x 151 mm 9.4 x 1.6 x 5.9 inches
DR-260 + 3G
239 x 40 x 159 mm 9.4 x 1.6 x 6.2 inches
Weight
Degree of protection
8
0.9 kg
IEC529
Enclosure
IP 40
Cooling
Convection
Mounting
Horizontal on 35 mm DIN-rail or flat on
level surface
6622-2231 • 29000448
Description
The DR-260-series is a multiple media ADSL router that provide the users with not only
a highly robust and fast ADSL-connection with all the ADSL-standards covered (ADSL to
ADSL2+) but also with the option of having multiple backup paths for redundancy, either via
cellular networks (GPRS/3G) or via legacy PSTN/ISDN connections.
The units give the user the option of being able to remotely access the PLCs, RTUs etc to
159,3 ±1
monitor the equipment,
access the web-configuration, send SMS or email, log to an FTP as well
as many other scenarios.151 ±0,5
With a feature rich software package, i.e. operating system, the unit provide functionality usually found in very costly competing products.
Instead of having to resort to expensive reprogramming or equipment change due to network
carriers discontinuing their leased line services use the Westermo products. A cost-effective
solution where the units listen to the legacy signals and transfer them securely across the
Internet completely transparent to the equipment!
Dimensional drawing
39,5 ±1
239 ±0,5
159,3 ±1
151 ±0,5
39,5 ±1
239 ±0,5
6622-2231 • 29000448
9
Interface specifications
Power
Rated voltage
Operating voltage
Rated current (max)
Rated frequency
11 – 28 VDC
11 – 28 VDC
1500 mA @ 12 VDC
DC
RS-232
Electrical specification
Data rate
Data format
Protocol
Circuit type
Transmission range
Connection
Shielded cable
Conductive housing
Number of ports
EIA RS-232
300 bit/s – 115.2 kbit/s
7 or 8 data bits, Odd, even or none parity, 1 or 2 stop bits
Transparent, optimised by packing algorithm
SELV
15 m / 49 ft
25 pin D-sub female
Not required
Yes
1
Ethernet TX
Electrical specification
Data rate
IEEE std 802.3. 2005 Edition
10 Mbit/s, 100 Mbit/s, manual or auto
Duplex
Full or half, manual or auto
Circuit type
SELV
Transmission range
100 m / 328 ft
Isolation to
All other
Connection
RJ-45 auto MDI/MDIX
Shielded cable
Conductive housing
Not required, except when installed in Railway applications as signalling
and telecommunications apparatus and located close to rails.*
Yes
Number of ports
4
* To minimise the risk of interference, a shielded cable is recommended when the cable is located inside 3 m
boundary to the rails and connected to this port. The cable shield should be properly connected (360º) to an earthing point within 1 m from this port. This earthing point should have a low impedance connection to the conductive enclosure of the apparatus cabinet, or similar, where the unit is built-in. This conductive enclosure should be connected to the earthing system of an installation and may be directly connected to the protective earth.
10
6622-2231 • 29000448
Antenna (option)
Frequency bands
Connection
850 MHz – 2100 MHz
SMA female, impedance: 50 ohm
SIM (option)
Electrical specification
Number of slots
3 volts SIM supported
2
USB
Electrical specification
Data rate
Circuit type
Maximum supply current
Connection
Number of ports
USB 2.0 host interface
Up to 12 Mbit/s (full-speed mode)
SELV
500 mA in total for both ports
USB receptacle connector type A
2
DSL
Data rate
Protocol
Connection
Shielded cable
Number of ports
Standard
ITU-T G.992.1 (ADSL)
ITU-T G.992.3 (ADSL2)
ITU-T G.992.5 (ADSL2+)
ANSI T1.413
50 Mbit Downlink, 3 Mbit Uplink
LLC/VC-MUX encap Ethernet, PPPoA, PPPoE, IPoA
RJ-11
Not required, except when installed in Railway applications as
signalling and telecommunications apparatus and located close
to rails.*
1
Annex
A,B (non overlap)
A,B,I,J,L,M (non overlap)
A,B,I,J,M (non overlap)
N/A
* To minimise the risk of interference, a shielded cable is recommended when the cable is located inside 3 m
boundary or the cable is longer than 30 m and inside 10 m boundary to the rails and connected to this port.
6622-2231 • 29000448
11
Connections
SIM Card Sockets
The two sockets at the left side of the front panel are for the GSM SIM card(s)
that you will receive from your service providers. SIM 1 and SIM 2
cannot be used to access two networks simultaneously.
The SIM card(s) should be inserted into SIM cardholders on the
right of the front panel as illustrated below.
In both cases, the end of the SIM card with the chamfered corner
should be inserted first. For SIM 1 the contacts should be face
down. For SIM 2 the contacts should be face up.
USB Host Connectors
LED Indicators
(for details
see next page)
DR-260
DSL Router
LAN
SIM 1
PWR
0
1
3G/GPRS
2
3
WLAN
DTE
DSL
SIGNAL
D
OH
NET SIM DAT
SIM 2
ISDN
B1
B2
CD DAT
PSTN
Antenna interface (optional)
Antenna interface (optional)
DSL interface
Ethernet interface
Power interface cord
Cable
Description
Black
– VDC
Red
+ VDC
RS-232 Interface
25-position
No. 2
No. 3
No. 4
No. 5
No. 6
No. 7
No. 8
No. 15
No. 17
No. 20
No. 22
No. 24
12
Direction
In
Out
In
Out
Out
Not connected
Out
Out
Out
In
Out
In
Description
Transmit Data (TD)
Receive Data (RD)
Request To Send (RTS )
Clear To Send (CTS)
Data Set Ready (DSR)
Signal ground (SG)
Data Carrier Detect (DCD) )
Transmitter Clock (TxC)
Receiver Clock (RxC)
Data Terminal Ready (DTR)
Ring Indicate (RI)
External Transmitter Clock (ETC)
6622-2231 • 29000448
LED Indicators
LED
Status
Description
PWR
OFF
Unit has no power
GREEN
All OK
RED
Lit until unit has started up
OFF
No link
GREEN
Link established
GREEN FLASH
Data traffic indication
WLAN
N/A
N/A
DTE
OFF
GREEN FLASH
No connection on serial port, or no data is transmitted or
received on the serial port
Terminal connected to the serial port and the DTR signal
is on
Data is transmitted or received on the serial port.
RED
No DSL link
GREEN
DSL link established
RED FLASH
DSL link negotiation
GREEN BLINK
Data traffic indication
OFF
No wireless network has been detected
GREEN
A wireless network has been detected
OFF
No valid SIM installed
GREEN
A valid SIM card is installed in the unit
OFF
No data is being transferred over the wireless network
GREEN
Data is being transferred over the wireless network
OFF
No signal / less than –113 dBm
1 LED
GREEN
Low signal strength / between –112 dBm and –87 dBm
2 LEDs
GREEN
Medium signal strength / between –86 dBm and –71 dBm
3 LEDs
GREEN
Strong signal strength / between –70 dBm and –51 dBm
D/OH
OFF
No ISDN connection
GREEN
Connected to ISDN Network and D-channel active
OFF
No ISDN B-channel 1 detected
GREEN
ISDN B-channel 1 active / data is being transferred
LAN 0,1,2,3
GREEN
DSL
3G /
GPRS
NET
SIM
DAT
SIGNAL ALL
ISDN
B1/CD
B2/DAT OFF
PSTN
D/OH
B1/CD
No ISDN B-channel 2 detected
GREEN
ISDN B-channel 2 active / data is being transferred
OFF
No PSTN connection
GREEN
Modem off-hook
OFF
Not connected to remote modem
GREEN
Connected to remote modem
B2/DAT OFF
GREEN
6622-2231 • 29000448
No Data is transferred
Data is being transferred
13
Protocols and Functionality
Ethernet Technologies
IEEE 802.3 for 10BaseT
IEEE 802.3u for 100BaseTX
ADSL Technologies
ITU-T G.992.1 ADSL (Annex A, B (non overlap))
ITU-T G.992.2 ADSL Lite (Annex A (non overlap))
ITU-T G.992.3 ADSL2 (Annex A, B, I, J, L, M (non overlap))
ITU-T G.992.5 ADSL2+ (Annex A, B, I, J, M (non overlap))
RFC2684 Bridged LLC and Bridged VC-MUX ATM encap. (ADSL)
ADSL2++ Quad spectrum downstream and double upstream
Cellular Technologies
(optional)
GSM
GPRS Multi-slot class 12, mobile station class B, PBCCH support, coding schemes CS 1-4
EDGE Multi-slot class 12 (max 236.8 Kbit/s), mobile station class B, modulation and coding scheme MCS 1-9
3G (WCDMA) 384 Kbit/s downlink / uplink
HSDPA up to 7.2 Mbit/s downlink
HSUPA up to 2.0 Mbit/s uplink
Modem Technologies
PSTN (Requires PSTN option)
ISDN (Requires ISDN option)
Serial Port Technologies
RS-232
Serial Over IP (Serial Extender and Virtual Serial Port)
LAPB
Resiliency and High
Availability
IEEE 802.1D Spanning Tree Protocol (STP)
IEEE 802.1w Rapid STP (RSTP)
Layer-2 Switching
IEEE 802.1Q Static VLAN and VLAN Tagging
IEEE 802.3x Flow Control
IGMPv2/v3 snooping
Static Multicast MAC filters
Layer-2 QoS
IEEE 802.1p Class of Service
Flexible classification VLAN tag, VLAN ID, IP DSCP/ToS, Port ID)
IP Routing, Firewall, VPN
and Cyber Security
Static IP routing
Dynamic IP routing
• BGP
• OSPFv2
• RIPv1/v2
VRRP, VRRP+™
GRE
Stateful inspection Firewall / ACL, NAT, 1:1 NAT, Port Forwarding
IPSec VPN including failover functionality, PSK & X.509, SCEP
L2TP
PPTP
OpenVPN / SSL VPN
TACACS+
RADIUS
SMS Control (Requires 3G Option)
14
6622-2231 • 29000448
Manageability
Management tools
• Web interface (HTTP and HTTPS)
• Command Line Interface (CLI) via console port, SSHv2 and
TELNET
• SNMPv1/v2c/v3
• Powerful Packet/Protocol Analyzer with PCAP-export support
• Flexible management of configuration and log files
• Local file management via HTTP, FTP, TFTP and SCP
• Load/save files from/to USB memory stick
• Upgrade firmware from USB memory stick
Flexible alarm/event handling system
Syslog (log files and remote syslog server)
Port Monitoring
SNTP (NTP client)
PPPoA & PPPoE client
DHCP client
DHCP server
DDNS
Programming Custom Control
ScriptBasic
6622-2231 • 29000448
15
Factory default/reset
Perform the following 4 steps to reset the unit to its factory default settings.
1. Power up the unit.
2. Locate the reset switch on the underside of the unit, near the front ventilation holes.
3. Press and hold the reset switch gently, with the tip of a pen or other similar device,
until you see the front LEDs flashing (~5 sec).
4. Remove the tip of the pen and wait for the unit to reboot.
Note! Do not power off the unit while the factory reset procedure is in place
Default Network Settings
IP address (Ethernet ports)
Netmask (Ethernet ports)
Username
Password
192.168.2.200
255.255.255.0
admin
westermo
Default DSL Settings
DSL Connection type
VPI / VCI
Authentication
ADSL/ADSL2/ADSL2+ on Annex A
0 / 38
PPPoA
Reset/set IP address using an RS-232 serial connection
If the IP address of the device is unknown the best way to access the unit is by performing a factory
reset, however, in some instances it may be required to only change, or set, the IP address of the
device. This can be achieved by connecting an RS-232 cable between the Serial 0 port on the device
to your PC.
RS-232 PC settings
Data rate
Data bits
Stop bits
Parity
Flow control
115.200 bit/s
8
1
None
None
Execute the following commands and change them to match your desired network settings.
Eth 0 ipaddr 192.168.2.200
Eth 0 mask 255.255.255.0
Eth 0 gateway 192.168.2.200
Eth 0 status
Config 0 save
The device can now be reached on the IP-address configured above.
16
6622-2231 • 29000448
DR-260
Step-by-step
guide to configure a DSL-connection using the web interface
DSL Router
LAN
SIM 1
PWR
0
1
3G/GPRS
2
3
WLAN
DTE
DSL
SIGNAL
NET SIM DAT
SIM 2
D
OH
ISDN
B1
B2
CD DAT
PSTN
Power Connection
ADSL connection (RJ-11)
PC/Ethernet connection (RJ-45)
Step 1 – Power-up the unit and wait for it to become ready
Connect the DR-260 to the DSL-network using the RJ-11, connect an RJ-45 cable from
one of the four Ethernet-ports to your PC, and then connect the unit to an appropriate
PSU and power it up.
The unit will start to negotiate the DSL-connection after approximately 15 – 20 seconds,
please note that the default settings might not be appropriate for your specific connection. Continue reading in order to assure that you have a valid setup.
Step 2 – Configure your PC
Make the following changes in your PC.
IP address
Netmask (Ethernet ports)
Gateway
Preferred DNS server
192.168.2.100*
255.255.255.0
192.168.2.200
192.168.2.200
* Can be any address in the 192.168.2.0-255-range except 192.168.2.200.
Note! If you are unsure or unable to change the above – consult your network administrator.
6622-2231 • 29000448
17
Step 3 – Accessing the unit
Start a web browser on your PC and type in the following address
http://192.168.2.200
Step 4 – Login screen
After step 3 you will be presented with a login screen which asks for a username and a password. Please type in the following
Username admin Password
westermo
Step 5 – Welcome screen
You have now successfully logged into the unit and are ready to set up your DSLconnection.
Please click on Network under the Configuration-menu item.
18
6622-2231 • 29000448
Step 6 – Alternative 1 – DSL Setup for PPPoA (e.g. UK) / PPPoE (e.g. DE)
The DR-260 comes pre-configured to match connections using ADSL with VPI/VCI set
to 0/38, authentication via PPPoA. Should the default settings not match your connection
you can always change the parameters to match your specific details.
Then click on DSL under the Interface-context.
Country
Sweden
Germany
United Kingdom
6622-2231 • 29000448
ADSL Settings per country
Provider
Annex
Mode
TeliaSonera
A
DHCP
Deutsche Telekom (DT) B
PPPoE
British Telecom (BT)
A
PPPoA
ATM Enc. VPI / VCI
LLC
8/35
LLC
1/32
LLC
0/38
19
In the DSL setup screen you configure the DSL-broadband connection according
to the information you received from your service provider.
When you are done, please press Apply and then Save to save your configuration.
20
6622-2231 • 29000448
Step 6 – Alternative 2 – DSL Setup for DHCP / Routed access (e.g. SE)
Some ISPs does not require any username or password and usually provides Internet
access via DHCP. To setup the DR-260 in those countries/ISPs please follow the actions
below.
First change from PPPoA LLC to Bridged Ethernet LLC under PVC Configuration
6622-2231 • 29000448
21
Make sure that the radio-button for Get an IP address automatically using DHCP
is selected.
22
6622-2231 • 29000448
Step 7 – Unit ready and online
The DR-260 will immediately start to negotiate the DSL-connection with the new
details after Step 6. To monitor the connection progress, navigate to Network Status→
Interfaces→ DSL. Under Modem Status you see the status of the DSL-connection.
Step 8 – Test your connection
In your Internet browser type in www.westermo.com and test your connection, you
should be able to see the Westermo website.
You are now ready to use the DR-260!
Change the IP address of the unit
First follow steps 1 through 5 above. Then click on Interfaces→ Ethernet → ETH 0 – LAN 0
Type the desired IP address into the text box next to IP Address and then press Apply
and Save.
6622-2231 • 29000448
23
Westermo • SE-640 40 Stora Sundby, Sweden
Tel +46 16 42 80 00 Fax +46 16 42 80 01 E-mail: info@westermo.com www.westermo.com
United Kingdom
Westermo Data Communications Talisman Business Centre Duncan Road, Park Gate, Southampton. SO31 7GA Tel: +44 (0) 1489 580 585 • Fax: +44 (0) 1489 580 586 sales@westermo.co.uk • www.westermo.co.uk
Germany
Westermo Data Communications Goethe Strasse 67 DE-68753 Waghäusel Tel: +49 (0) 7254 95400-0 • Fax: +49 (0) 7254-95400-9 info@westermo.de • www.westermo.de
Austria
Westermo Data Communications Tel: +43 (0) 72030 3920 • Fax: +43 (0) 2235 86131 info@westermo.at • www.westermo.at
France
Westermo Data Communications Bat. A, 9 Chemin de Chilly FR-91160 Champlan Tel: +33 1 69 10 21 00 • Fax: +33 1 69 10 21 01 infos@westermo.fr • www.westermo.fr
North America
Westermo Data Communications 939 N. Plum Grove Road, Suite F, IL 60173 Schaumburg, USA Tel: +1 847 619 6068 • Fax: +1 847 619 66 74 info@westermo.com • www.westermo.com
Singapore
Westermo Data Communications 84 Genting Lane #07-03 Cityneon Design Centre Singapore 349584 Tel: +65 6743 9801 • Fax: +65 6745 0670 sales@westermo.com.sg • www.westermo.com
Malaysia
Westermo Data Communications 84 Genting Lane #07-03, Cityneon Design Centre, Singapore 349584 Tel : +6 012 2781156 • Fax : +603 8062 7467 chinleong.teh@westermo.com.sg • www.westermo.com.sg
China
Westermo Data Communications 2F Building B No.1618 Yishan Road Shanghai 201103 Tel: +86 21 6145 0400 • Fax: +86 21 6145 0499 sales.cn@westermo.com • www.cn.westermo.com
Westermo Teleindustri AB have distributors in several countries, contact us for further information.
REV.D 6622-2231 29000448 2013-03 Westermo Teleindustri AB, Sweden – A Beijer Electronics Group Company
Sales Units
Sweden
Westermo Data Communications Svalgången 1, Vallbyinstitutet, 724 81 Västerås Tel: +46 (0) 21 548 08 00 • Fax: (0) 21 35 18 50 info.sverige@westermo.se • www.westermo.se