www.wackergroup.com
0160534en
0107
Generator
GP 6600A
GPS 6600A
OPERATOR’S MANUAL
0
1
6
0
5
3
4
E
N
003
DANGER
CARBON MONOXIDE
Using a generator indoors CAN KILL YOU IN MINUTES.
Generator exhaust contains carbon monoxide (CO). This is a poison you cannot see or
smell. If you can smell the generator exhaust, you are breathing CO. But even if you cannot
smell the exhaust, you could be breathing CO.
•
NEVER use a generator inside homes, garages, crawlspaces, or other partly enclosed
areas. Deadly levels of carbon monoxide can build up in these areas. Using a fan or
opening windows and doors does NOT supply enough fresh air.
•
ONLY use a generator outside and far away from windows, doors, and vents. These
openings can pull in generator exhaust.
Even when you use a generator correctly, CO may leak into the home. ALWAYS use a
battery-powered or battery-backup CO alarm in the home.
If you start to feel sick, dizzy, or weak after the generator has been running, move to fresh
air RIGHT AWAY. See a doctor. You could have carbon monoxide poison.
GP/GPS 6600A
Table of Contents
1.
Foreword
2.
California Evaporative Emission Control Warranty Statement 6
3.
Safety Information
3.1
3.2
3.3
3.4
3.5
3.6
4.
8
Laws Pertaining to Spark Arresters ...................................................... 8
Operating Safety .................................................................................. 9
Operator Safety while using Internal Combustion Engines ................ 11
Service Safety .................................................................................... 12
Label Locations .................................................................................. 13
Safety and Operating Labels .............................................................. 14
Technical Data
4.1
4.2
5.
5
18
Generator ........................................................................................... 18
Engine ................................................................................................ 20
Operation
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
5.9
5.10
5.11
5.12
5.13
5.14
5.15
5.16
5.17
5.18
5.19
21
Determining Power Requirements ..................................................... 21
Outdoor Installation ............................................................................ 22
Indoor Installation ............................................................................... 22
Recommended Battery (GPS only) .................................................... 22
Battery Installation (GPS only) ........................................................... 23
Wheel Kit ............................................................................................ 24
Generator Derating ............................................................................. 26
Grounding the Generator ................................................................... 27
Operating Heavy Loads ...................................................................... 27
Use of Extension Cords ...................................................................... 28
Control Panel ...................................................................................... 29
Ground Fault Interrupt (GFI) ............................................................... 30
Twist-Lock Receptacles ..................................................................... 30
Engine Auto Idle ................................................................................. 31
Engine Speed ..................................................................................... 31
Voltage Selection ............................................................................... 32
Before Starting ................................................................................... 33
To Start ............................................................................................... 34
To Stop ............................................................................................... 35
3
Table of Contents
6.
GP/GPS 6600A
Maintenance
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
6.9
6.10
6.11
6.12
6.13
6.14
6.15
36
Engine Maintenance ............................................................................36
Periodic Maintenance Schedule ..........................................................36
Engine Oil ............................................................................................37
Servicing Air Cleaner ...........................................................................38
Spark Plug ...........................................................................................39
Cleaning the Sediment Cup ................................................................40
Carburetor Adjustment ........................................................................40
Adjusting Engine Speed ......................................................................41
Storage ................................................................................................42
Transport .............................................................................................42
Troubleshooting ...................................................................................43
Wire Colors ..........................................................................................43
Electrical Schematic ............................................................................44
Electrical Schematic (CAN models only) .............................................46
Engine Schematic ...............................................................................48
wc_bo0160534en_003TOC.fm
4
WARNING
1.
CALIFORNIA
Proposition 65 Warning:
Engine exhaust, some of its constituents, and certain vehicle
components, contain or emit chemicals known to the State of
California to cause cancer and birth defects or other reproductive
harm.
Foreword
This manual provides information and procedures to safely operate
and maintain this Wacker model. For your own safety and protection
from injury, carefully read, understand and observe the safety
instructions described in this manual.
Keep this manual or a copy of it with the machine. If you lose this
manual or need an additional copy, please contact Wacker
Corporation. This machine is built with user safety in mind; however,
it can present hazards if improperly operated and serviced. Follow
operating instructions carefully! If you have questions about operating
or servicing this equipment, please contact Wacker Corporation.
The information contained in this manual was based on machines in
production at the time of publication. Wacker Corporation reserves the
right to change any portion of this information without notice.
All rights, especially copying and distribution rights, are reserved.
Copyright 2007 by Wacker Corporation.
No part of this publication may be reproduced in any form or by any
means, electronic or mechanical, including photocopying, without
express written permission from Wacker Corporation.
Any type of reproduction or distribution not authorized by Wacker
Corporation represents an infringement of valid copyrights and will be
prosecuted. We expressly reserve the right to make technical
modifications, even without due notice, which aim at improving our
machines or their safety standards.
5
California Evaporative Emission Control Warranty Statement
2.
California Evaporative Emission Control Warranty Statement
YOUR WARRANTY RIGHTS AND OBLIGATIONS
The California Air Resources Board and Wacker Corporation, Inc. are
pleased to explain the evaporative emission control system (EECS)
warranty on your model year 2006 and later portable generator. In
California, new portable generators must be designed, built and
equipped to meet the State’s stringent anti-smog standards. Wacker
Corporation must warrant the EECS on your portable generator for the
period of time listed below provided there has been no abuse, neglect
or improper maintenance of your portable generator.
Your EECS on your model year 2006 and later portable generator
includes the fuel line, fuel line clamps and fuel line fittings.
Where a warrantable condition exists, Wacker Corporation will repair
your portable generator at no cost to you including diagnosis, parts and
labor.
MANUFACTURER’S WARRANTY COVERAGE:
This EECS is warranted for two years from the initial date of purchase.
If any evaporative emission-related part on your equipment is
defective, the part will be repaired or replaced by Wacker Corporation
at no charge to you. The owner shall not be charged for diagnostic
labor that leads to determination that a warranted part is in fact
defective, provided that such diagnostic work is performed at a Wacker
Corporation’s authorized service center.
WARRANTY PERIOD:
Any warranted part that is not scheduled for replacement as required
maintenance, or which is scheduled only for regular inspection to the
effect of “repair or replace as necessary” shall be warranted for two
years. Any warranted part that is scheduled for replacement as
required maintenance shall be warranted for a time not less than the
remaining warranty period.
6
California Evaporative Emission Control Warranty Statement
OWNER’S WARRANTY RESPONSIBILITIES:
As the portable generator owner, you are responsible for performance
of the required maintenance listed in your owner’s manual. Wacker
Corporation recommends that you retain all receipts covering
maintenance on your portable generator, but Wacker Corporation
cannot deny warranty solely for the lack of receipts.
As the portable generator owner, you should however be aware that
Wacker Corporation may deny you warranty coverage if your portable
generator or a part has failed due to abuse, neglect, or improper
maintenance or unapproved modifications.
You are responsible for presenting your portable generator to Wacker
Corporation’s authorized service center as soon as the problem exists.
The warranty repairs should be completed in a reasonable amount of
time, not to exceed 30 days. If you have a question regarding your
warranty coverage, you should contact your nearest authorized
Wacker service center or call 1-800-770-0957.
WHAT IS NOT COVERED:
All failures caused by abuse, neglect, or improper maintenance are not
covered. In addition, the use of add-on or modified parts will be
grounds for disallowing a warranty claim.
WARRANTED PARTS:
The repair or replacement of any warranted part otherwise eligible for
warranty coverage may be excluded from such warranty coverage if
Wacker Corporation demonstrates that the portable generator has
been abused, neglected, or improperly maintained, and that such
abuse, neglect, or improper maintenance was the direct cause of the
need for repair or replacement of the part. That notwithstanding, any
adjustment of a component that has a factory installed, and properly
operating, adjustment limiting device is still eligible for warranty
coverage. The following emission warranty parts list is covered:
(1)Fuel Line.
(2)Fuel Line Clamps.
(3)Fuel Line Fittings.
7
Safety Information
3.
GP/GPS 6600A
Safety Information
This manual contains DANGER, WARNING, CAUTION, NOTICE and
NOTE callouts which must be followed to reduce the possibility of
personal injury, damage to the equipment, or improper service.
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that follow this
symbol to avoid possible injury or death.
DANGER indicates a hazardous situation which, if not avoided, will
result in death or serious injury.
DANGER
WARNING indicates a hazardous situation which, if not avoided, could
result in death or serious injury.
WARNING
CAUTION indicates a hazardous situation which, if not avoided, could
result in minor or moderate injury.
CAUTION
NOTICE: Used without the safety alert symbol, NOTICE indicates a
hazardous situation which, if not avoided, could result in property
damage
Note: Contains additional information important to a procedure.
3.1
Laws Pertaining to Spark Arresters
Notice: State Health Safety Codes and Public Resources Codes
specify that in certain locations spark arresters be used on internal
combustion engines that use hydrocarbon fuels. A spark arrester is a
device designed to prevent accidental discharge of sparks or flames
from the engine exhaust. Spark arresters are qualified and rated by
the United States Forest Service for this purpose.
In order to comply with local laws regarding spark arresters, consult
the engine distributor or the local Health and Safety Administrator.
8
GP/GPS 6600A
3.2
Safety Information
Operating Safety
DANGER
WARNING
BACKFEED FROM THE GENERATOR INTO THE PUBLIC POWER
DISTRIBUTION SYSTEM CAN CAUSE SERIOUS INJURY OR
DEATH TO UTILITY WORKERS!
Improper connection of generator to a building's electrical system can
allow electrical current from the generator to backfeed into utility lines.
This may result in electrocution of utility workers, fire, or explosion.
Connections to a building's electrical system must be made by a
qualified electrician and comply with all applicable laws and electrical
codes.
If connected to a building's electrical system the generator must meet
the power, voltage, and frequency requirements of the equipment in
the building. Differences in power, voltage, and frequency
requirements may exist and improper connection may lead to
equipment damage, fire, and personal injury or death.
Familiarity and proper training are required for the safe operation of
equipment. Equipment operated improperly or by untrained personnel
can be dangerous. Read the operating instructions contained in both
this manual and the engine manual and familiarize yourself with the
location and proper use of all controls. Inexperienced operators should
receive instruction from someone familiar with the equipment before
being allowed to operate the machine.
3.2.1
NEVER operate the generator when open containers of fuel, paint, or
other flammable liquids are near.
3.2.2
NEVER operate the generator, or tools attached to the generator, with
wet hands.
3.2.3
NEVER use worn electrical cords. Severe electrical shock and
equipment damage may result.
3.2.4
NEVER run the electrical cords under the generator, or over vibrating
or hot parts.
3.2.5
NEVER enclose or cover the generator when it is in use or when it is
hot.
3.2.6
NEVER overload the generator. The total amperage of the tools and
equipment attached to the generator must not exceed the load rating
of the generator.
3.2.7
NEVER operate the machine in snow, rain, or standing water.
3.2.8
NEVER allow untrained personnel to operate or service the generator.
The generator set should be set up by a trained electrician.
3.2.9
NEVER stand on the machine.
3.2.10
DO NOT stand under the machine while it is being hoisted or moved.
3.2.11
DO NOT attach equipment to the machine when it is suspended.
9
Safety Information
GP/GPS 6600A
3.2.12 ALWAYS store the equipment properly when it is not being used.
Equipment should be stored in a clean, dry location out of the reach of
children.
3.2.13 ALWAYS position and operate
noncombustible, level surface.
the
generator
on
a
firm,
3.2.14 ALWAYS transport the generator in an upright position.
3.2.15 ALWAYS keep the machine at least one meter (three feet) away from
structures, buildings, and other equipment during use.
3.2.16 ALWAYS keep the area immediately surrounding and underneath the
machine clean, neat, and free of debris and combustible materials.
Make sure that the area overhead is clear of debris that could fall onto
or into the machine or exhaust compartment.
3.2.17 ALWAYS remove all tools, cords, and other loose items from the
generator before starting it.
3.2.18 ALWAYS make certain the machine is well-grounded and securely
fastened to a good earthen ground per national and local regulations.
10
GP/GPS 6600A
3.3
Safety Information
Operator Safety while using Internal Combustion Engines
DANGER
Internal combustion engines present special hazards during operation
and fueling. Read and follow the warning instructions in the engine
owner’s manual and the safety guidelines below. Failure to follow the
warnings and safety guidelines could result in severe injury or death.
3.3.1
DO NOT run the machine indoors or in an enclosed area such as a
deep trench unless adequate ventilation, through such items as
exhaust fans or hoses, is provided. Exhaust gas from the engine
contains poisonous carbon monoxide gas; exposure to carbon
monoxide can cause loss of consciousness and may lead to death.
3.3.2
DO NOT smoke while operating the machine.
3.3.3
DO NOT smoke when refueling the engine.
3.3.4
DO NOT refuel a hot or running engine.
3.3.5
DO NOT refuel the engine near an open flame.
3.3.6
DO NOT spill fuel when refueling the engine.
3.3.7
DO NOT run the engine near open flames.
3.3.8
DO NOT start the engine if fuel has spilled or a fuel odor is present.
Move the generator away from the spill and wipe the generator dry
before starting.
3.3.9
ALWAYS refill the fuel tank in a well-ventilated area.
3.3.10
ALWAYS replace the fuel tank cap after refueling.
3.3.11
ALWAYS check the fuel lines and the fuel tank for leaks and cracks
before starting the engine. Do not run the machine if fuel leaks are
present or the fuel lines are loose.
11
Safety Information
3.4
GP/GPS 6600A
Service Safety
WARNING
Poorly maintained equipment can become a safety hazard! In order
for the equipment to operate safely and properly over a long period of
time, periodic maintenance and occasional repairs are necessary. If
the generator is experiencing problems or is being serviced, attach a
“DO NOT START” sign to the control panel to notify other people of its
condition.
3.4.1
DO NOT use gasoline or other types of fuels or flammable solvents to
clean parts, especially in enclosed areas. Fumes from fuels and
solvents can become explosive.
3.4.2
DO NOT attempt to clean or service the machine while it is running.
3.4.3
DO NOT modify the equipment without the express written approval of
the manufacturer.
3.4.4
DO NOT allow water to accumulate around the base of the machine.
If water is present, move the machine and allow the machine to dry
before servicing.
3.4.5
DO NOT service the machine if your clothing or skin is wet.
3.4.6
DO NOT allow untrained personnel to service this equipment. Only
trained electrical technicians should be allowed to service the electrical
components of this equipment.
3.4.7
ALWAYS keep the machine clean and labels legible. Replace all
missing and hard-to-read labels. Labels provide important operating
instructions and warn of dangers and hazards.
3.4.8
ALWAYS replace the safety devices and guards after repairs and
maintenance.
3.4.9
ALWAYS let the engine cool before transporting or servicing it.
3.4.10 ALWAYS keep hands, feet, and loose clothing away from the moving
parts on the generator and engine.
3.4.11 ALWAYS turn the engine off before servicing the machine. If the
engine has electric start, disconnect the negative terminal on the
battery before servicing the machine.
3.4.12 ALWAYS keep the fuel lines in good condition and properly connected.
Leaking fuel and fumes are extremely explosive.
12
GP/GPS 6600A
Label Locations
GND
13
88897
3.5
Safety Information
Safety Information
3.6
GP/GPS 6600A
Safety and Operating Labels
Wacker machines use international pictorial labels where needed.
These labels are described below:
Label
Meaning
WARNING!
Hot surface!
CAUTION!
Read and understand the supplied Operator’s
Manuals before operating this machine. Failure to do so increases the risk of injury to yourself or others.
CAUTION!
Lifting point.
GND
88897
Electrical ground
14
GP/GPS 6600A
Label
Safety Information
Meaning
Press circuit breaker switch to OFF position.
Check the fuel level.
Open the fuel flow valve.
Press engine switch to ON position.
GPS - Press ignition switch.
GP - Pull the rewind starter.
Press circuit breaker switch to ON position.
Press engine switch to OFF position.
15
Safety Information
Label
GP/GPS 6600A
Meaning
Close the fuel flow valve.
DANGER!
Asphyxiation hazard. Read the operator’s
manual for instructions.
Use in a well-ventilated area. Do not use
indoors or near open windows. Fumes can
cause death.
WARNING!
To reduce the risk of electrical shock, read the
operator’s manual. Improper connection of the
generator to a building’s electrical system can
allow electrical current from the generator to
backfeed into utility lines. This may result in
electrocution of utility workers, fire or explosion. Connections to a building’s electrical system must be made by a qualified electrician
and comply with all applicable laws and electrical codes.
A nameplate listing the model number, item
number, revision number, and serial number is
attached to each unit. Please record the information found on this plate so it will be available
should the nameplate become lost or damaged. When ordering parts or requesting service information, you will always be asked to
specify the model number, item number, revision number, and serial number of the unit.
16
GP/GPS 6600A
Label
Safety Information
Meaning
Important Emissions Information
This equipment meets California EVP
emission regulations for small off-road
engines.
This machine may be covered by one or more
patents.
DANGER!
No sparks, flames or burning objects near
machine.
Shut off the engine before refueling.
17
Technical Data
4.
GP/GPS 6600A
Technical Data
4.1
Generator
Item No.
GP 6600A
0620014
GP 6600A
0620015
GPS 6600A
0620016
Generator
Maximum Output
W
6600
Continuous Output
W
6000
Type
AC Voltages
available
Frequency
Dual voltage, single phase,
Auto voltage regulator system
120 / 240
1ø
volts
phase
60
Hz
Power Factor
1.0
AC receptacles:
125V GFI duplex
125V GFI duplex
125V twist-lock
125V/250V twist-lock
amp
amp
amp
amp
20
20
30
30
Main Circuit Breaker
amp
2-pole, 27 amp each pole
LxWxH
mm
(in.)
Weight (dry)
Kg (lbs.)
685 x 530 x 520
(27 x 21 x 20.5)
1005 x 685 x 660
(39.5 x 27 x 26)
870 x 530 x 520
(34.3 x 21 x 20.5)
87 (192)
96.6 (213)
94 (207.5)
18
GP/GPS 6600A
Technical Data
Item No.
GP 6600A CAN
0620045
GP 6600A CAN
0620046
GPS 6600A CAN
0620047
Generator
Maximum Output
W
6600
Continuous Output
W
5500
Type
AC Voltages
available
Frequency
Dual voltage, single phase,
Auto voltage regulator system
120 / 240
1ø
volts
phase
60
Hz
Power Factor
1.0
AC receptacles:
125V GFI duplex
125V GFI duplex
125V twist-lock
125V/250V twist-lock
amp
amp
amp
amp
20
20
30
30
Main Circuit Breaker
amp
2-pole, 27 amp each pole
LxWxH
mm
(in.)
Weight (dry)
Kg (lbs.)
685 x 530 x 520
(27 x 21 x 20.5)
1005 x 685 x 660
(39.5 x 27 x 26)
870 x 530 x 520
(34.3 x 21 x 20.5)
87 (192)
96.6 (213)
94 (207.5)
19
Technical Data
4.2
GP/GPS 6600A
Engine
Item No.
GP 6600A
GP 6600A
CAN
0620045
0620046
0620014
0620015
GPS 6600A
0620016
GPS 6600A
CAN
0620047
Engine
Engine Type
Single cylinder, 4-cycle, air-cooled, gasoline engine
Engine Make
Honda
Engine Model
GX 390
Rated Power
9.7 (13)
kW (Hp)
Spark Plug
Electrode Gap
Champion RN10Y
Operating Speed
(Max.)
rpm
Air Cleaner
type
Battery
Engine Lubrication
Engine Oil Capacity
Fuel
Fuel Tank Capacity
Fuel Consumption
Running Time
0.7–0.8 (0.028–0.031)
mm (in.)
3600
Dry type with oil-wetted foam pre-cleaner
type
rating
size (in.)
oil grade
Y50-N18L-A
12V - 20 Amp-horo
8-1/8 x 3-9/16 x 6-7/16
N/A
SAE 10W30 service class SF, SE, SD, or SC
1.1 (1.2)
l (qts.)
Regular unleaded gasoline
type
19.5 (5.2)
l (gal.)
3.9 (4.1)
l (qts.)/hr.
5
hrs.
20
GP/GPS 6600A
5.
Operation
Operation
5.1
Determining Power Requirements
This generator is designed to operate single-phase, 60 Hz appliances
running at 120 VAC or 240 VAC. Check the nameplate or label
provided on tools and appliances to make sure their power
requirements match the power output of the generator.
Some appliances and tools require a surge of current when starting.
This means that the amount of power needed to initially start the
equipment is larger than the power required to keep it running. The
generator must be capable of supplying this “surge” current. Other
types of appliances require more power than is actually stated on their
nameplate.
The information in “Approximate Starting Power Requirements” is
offered only as a general guideline to help you in determining power
requirements for different types of equipment. Check with your nearest
Wacker Dealer, or contact the manufacturer or dealer of the tool or
appliance, with questions regarding its power requirements.
NOTICE: If a tool or appliance does not reach full speed within a few
seconds when switched on, turn it off immediately to avoid damage.
Approximate Starting Power Requirements
•
Incandescent lights and appliances such as irons and hot plates,
which use a resistive-type heating element, require the same wattage
to start and run as is stated on their nameplates.
•
Fluorescent and mercury lamps require 1.2–2 times their stated wattage to start.
•
Electrical motors and many types of electrical tools often require a
large starting current. The amount of starting current depends on the
type of motor and its use.
•
Most electrical tools require 1.2–3 times their stated wattage for starting.
•
Loads such as submersible pumps and air compressors require a
very large force to start. They need as much as 3–5 times the wattage
stated on the nameplate in order to start.
If the wattage is not given for a particular tool or appliance, it can be
calculated by multiplying its voltage and amperage requirements:
Single Phase: VOLTS x AMPS = WATTS
Three Phase: VOLTS x AMPS x 1.732 x 0.8 = WATTS
21
Operation
5.2
GP/GPS 6600A
Outdoor Installation
Place the generator in an area where it will not be exposed to rain,
snow, or direct sunlight. Make sure it is positioned on firm, level
ground, so it will not slide or shift. Position the engine exhaust away
from areas where people may be present.
If operating the generator inside a tunnel or deep trench, make sure
there is adequate ventilation. Precautions similar to those required
when operating indoors may be necessary.
The surrounding area must be free from water and moisture. All
components must be protected from excessive moisture.
5.3
Indoor Installation
DANGER
5.4
If the generator must be installed indoors, adequate ventilation or
exhaust hoses must be provided. When venting exhaust fumes, make
sure the exhaust piping is large enough to prevent excessive back
pressure to the engine. Back pressure reduces engine efficiency and
may cause the engine to overheat.
Exhaust gas from the engine contains poisonous carbon monoxide
gas; exposure to carbon monoxide can cause loss of consciousness
and may lead to death. Never run the generator indoors or in an
enclosed area unless adequate ventilation, through such items as
exhaust hoses or fans, is provided.
When installed indoors, steps to prevent fire and explosion such as
providing a good, earthen ground, removing all flammable materials
near the generator, and using only electrical cables in good condition,
must be observed. See Operating Safety.
Recommended Battery (GPS only)
This generator is shipped without a battery. The recommended battery
to be used is:
Battery Type
50-N18L-A
Voltage
12 V
Capacity
20 A/h
LxWxH
206 x 90 x 164 mm
(8-1/8 x 3-9/16 x 6-7/16 in.)
22
GP/GPS 6600A
5.5
Operation
Battery Installation (GPS only)
See Graphic: wc_gr002701
5.5.1
Align the holes found in the battery tray (a) to the holes on the frame
cross-member
5.5.2
Insert M8 x 14 screws (b) through the tray then through the holes of
the cross-member.
5.5.3
Insert the nuts (c) onto the screws and tighten. Torque nuts to 18.75
Nm. (13.5 ft.lbs).
5.5.4
Align the holes in the battery tube (d) to the holes in front of the battery
tray.
5.5.5
Insert M8 x 35 screws (e) through the battery tray then through the
tube.
5.5.6
Insert the nuts (f) onto the screws and tighten. Torque nuts to 18.75
Nm. (13.5 ft.lbs).
5.5.7
Insert the tube clamps (g) onto the upper frame tube and align the
holes to the holes of the battery tube.
5.5.8
Insert M8 x 35 screws (h) through the battery tube then through the
tube clamps.
5.5.9
Insert the nuts (j) onto the bolts and tighten. Torque nuts to 18.75 Nm.
(13.5 ft.lbs).
5.5.10
Slide the J-bolt (k) through the holes found in the battery holder (l).
5.5.11
Insert the rounded end of the J-bolt (k) into the slot of the battery tray
and insert the tip of the J-bolt through the hole.
23
Operation
5.6
GP/GPS 6600A
Wheel Kit
See Graphic: wc_gr002658
The wheel kit (Part No. 0161308) is a standard item on Item Number
0620012, 0620015, 0620043 and 0620046 only. It is available as an
option on all other models.
5.6.1
Hoist the generator, and align the axle (c) with the lower cross-member
of frame.
5.6.2
Insert the axle brackets (k) over the axle and align the holes found in
the axle bracket to the holes of the cross-member. Ensure that the
brackets extend under the tube of the frame.
5.6.3
Insert M6 x 16 screws (l) through the outer holes on the cross-member,
then through the holes of the axle bracket.
5.6.4
Insert M6 nuts (m) onto the screws and tighten. Torque to 7.5 Nm (5.25
ft.lbs.).
5.6.5
Assemble the washers (g) next to the rings (h), then add the wheels
(d).
5.6.6
Add the washers (g) next to the wheels, then insert the pins (f) into the
holes of the axle and separate the legs of the pins.
5.6.7
Align the holes found in the leg bracket (b) to the holes of the lower
cross-member.
5.6.8
Insert M6 x 16 screws (l) through the outer holes on the cross-member,
then through the holes of the leg bracket.
5.6.9
Insert M6 nuts (n) onto the screws and tighten. Torque to 7.5 Nm (5.25
ft.lbs.).
5.6.10 Insert M8 x 30 screw (o) through the hole in the leg bracket and
through the hole in cross-member.
5.6.11 Insert M8 nut (p) onto the screw and tighten. Torque to 18.75 Nm (13.5
ft.lbs.).
5.6.12 Align the holes in the rubber foot mounts (e) to the holes of the leg
bracket.
5.6.13 Insert M6 x 20 screws (m) through the leg bracket, then through the
holes of the rubber foot mounts.
5.6.14 Insert the nuts (n) onto the screws and tighten. Torque to 7.5 Nm (5.25
ft.lbs.).
5.6.15 Align the holes found in the handles (a, j) to the holes of the brackets
(1) on the frame.
5.6.16 Insert M6 x 16 screws (l) through the handles, then through the
brackets on the frame.
5.6.17 Insert nuts (m) onto the screws and tighten. Torque to 7.5 Nm (5.25
ft.lbs.).
24
GP/GPS 6600A
Operation
25
Operation
5.7
GP/GPS 6600A
Generator Derating
All generators are subject to derating for altitude and temperature.
Internal combustion engines, unless modified, run less efficiently at
higher altitudes due to the reduction of air pressure. This translates
into a lack of power and thus reduction in generator output.
Temperature affects both engine and generator performance. As
temperature increases, an engine will run less efficiently and more
resistance will be found in electrical components. Therefore, as the
temperature increases, the output of the generator decreases. Altitude
also affects the cooling capacity of air—the higher the altitude the less
dense the air is and thus the lower its ability to transfer heat.
For every increase in altitude of 500 m (1650 ft.) above 1000 m (3300
ft.), the output of the generator will be reduced by 3%. For every
increase of 5° C (9° F) in ambient temperature above 40° C (104° F),
the output of the generator will be reduced by 3%. Use the tables
shown for altitude and temperature deration factors. It may be
necessary to consider both altitude and ambient temperature deration
factors to determine true generator output.
Ambient Temp.
°C (°F)
Derate
Factor
45 (113)
3%
0.97
50 (122)
6%
0.94
55 (131)
9%
0.91
60 (140)
12 %
0.88
Altitude
m (ft.)
Derate
Factor
1500 (4900)
3%
0.97
2000 (6600)
6%
0.94
2500 (8200)
9%
0.91
3000 (9900)
12 %
0.88
3500 (11500)
15 %
0.85
4000 (13100)
18 %
0.82
26
GP/GPS 6600A
5.8
Operation
Grounding the Generator
See Graphic: wc_gr000544
A ground connection (a) is located on the generator frame. For proper
operating safety, this ground terminal must be connected to a good
ground source. This ground connection must comply with National
Electrical Code standards, and state and local regulations.
5.9
Operating Heavy Loads
Limit operations requiring the maximum rated output of 6600 W to 20–
30 minutes. For continuous operation do not exceed the continuous
rated output of 6000 W (CAN models = 5500 W).
NOTICE: DO NOT exceed the current limit specified on the control
panel for any receptacle.
27
Operation
GP/GPS 6600A
5.10 Use of Extension Cords
WARNING
Current
When a long extension cord is used to connect an appliance or tool to
the generator, a voltage loss occurs—the longer the cord, the greater
the voltage loss. This results in less voltage being supplied to the
appliance or tool and increases the amount of current draw or reduces
performance. A heavier cord with a larger wire size will reduce the
voltage loss.
Damaged extension cords can cause electrical shock, resulting in
serious injury or death. DO NOT use worn, bare, or frayed cords.
Replace damaged cords immediately.
Use the chart below as a guide for selecting proper cable size.
Load in Watts
Maximum Cable Length in Feet
(Amps)
120V
240V
#10
#12
#14
#16
2.5
300
600
1000.
600
375
250
5
600
1200
500
300
200
125
7.5
900
1800
350
200
125
100
10
1200
2400
250
150
100
-
15
1800
3600
150
100
65
-
20
2400
4800
125
75
50
-
Use only extension cords rated for outdoor use and equipped with a
third-wire ground.
NOTICE: Operating equipment at low voltage can cause it to overheat.
28
GP/GPS 6600A
Operation
5.11 Control Panel
See Graphic: wc_gr002498
Ref.
Description
Ref.
Description
a
Engine Switch
g
GFI test button
b
Auto Idle Switch
h
GFI reset button
c
Twist-lock receptacle - 120V
j
Twist-lock receptacle - 120/240V
d
Main Circuit Breaker
k
Ignition Switch (GPS only)
e
Voltage Selector Switch
m
20A circuit breaker (CAN only)
f
GFI Duplex receptacle - 120V
n
30A circuit breaker (CAN only)
29
Operation
GP/GPS 6600A
5.12 Ground Fault Interrupt (GFI)
See Graphic: wc_gr002498
The two receptacles (f) are protected by a ground fault circuit interrupt
(GFI). The GFI shuts off the power to the receptacle when a ground
fault occurs in the generator or to a piece of equipment attached to the
generator.
The GFI should be tested for proper operation every time the generator
is used.
To test the GFI:
Start the generator. Turn the auto idle “OFF”. Push the TEST button
(h) on the receptacle in. The RESET button (g) will pop out. The power
is now off at the receptacles. If the RESET button does not pop out, the
GFI is not working. Do not run the generator until the problem can be
corrected. To restore power to the receptacles, push the RESET
button in.
If the RESET button pops out during operation, stop the generator and
check the generator and equipment for defects.
5.13 Twist-Lock Receptacles
See Graphic: wc_gr002498
Twist-lock receptacles (c, j) are used at the 120V 30A and 120/240V
30A outlets. These receptacles are not protected by the GFI.
To attach a power cord to a twist-lock receptacle, insert the plug into
the receptacle and turn it clockwise to lock it in place.
30
GP/GPS 6600A
Operation
5.14 Engine Auto Idle
See Graphic: wc_gr002498
The auto idle switch (b) automatically reduces engine speed
approximately 7 seconds after all appliances or tools attached to the
generator have been turned off. The engine automatically returns to
full speed when a tool or appliance is turned back on.
To turn the auto idle feature on, push the auto idle switch to “AUTO”.
The AUTO setting is recommended while the generator is running to
minimize fuel consumption. To avoid extended engine warm-up
periods, keep switch set to “OFF” when starting the engine and until
the engine reaches operating temperature.
5.15 Engine Speed
Generators require a fixed engine speed to maintain the correct
voltage. Engine speed is controlled by a governor which automatically
adjusts to varying loads on the engine to maintain a constant speed.
See Technical Data. There is no throttle control. Use the auto idle
switch on the generator to control engine speed.
31
Operation
GP/GPS 6600A
5.16 Voltage Selection
See Graphic: wc_gr002497
The voltage selector switch (e) allows the generator to operate in either
single (120V) or dual voltage (120/240V) mode.
In single-voltage mode, use only the 120V twist-lock (c) and duplex
receptacles (f1, f2). The full rated power of the generator is shared
between the three receptacles.
In dual voltage mode both the 120V and 120/240V receptacles are
powered; lower watts are available on receptacles (f1, f2, c). The 120/
240V twist-lock receptacle (j) should be used in dual mode only. To
achieve full power in this receptacle it should be used alone.
NOTICE: NEVER switch the voltage selector switch with the main
breaker on! This can cause arcing and can damage the generator.
Turn all tools and appliances off and place main breaker (d) in the OFF
position before changing voltage switch position.
32
GP/GPS 6600A
Operation
5.17 Before Starting
5.17.1
Read and understand the safety and operating labels and instructions
at the beginning of this manual
5.17.2
Inspect the generator for any signs of damage which may affect
operation or pose a safety hazard.
5.17.3
Check:
•
oil level in engine
•
fuel level
•
condition of air cleaner
•
tightness of external fasteners
•
condition of fuel lines.
Note: The engine is equipped with an oil alert system. If the oil level in
the engine drops too low, the engine will not start.
5.17.4
Fill the fuel tank with fresh, regular, unleaded grade gasoline. DO NOT
use an oil/gas mixture. The use of gasohol or any fuel containing more
than 10% ethanol is not recommended. Consult the engine owner's
manual for complete fuel specifications.
33
Operation
GP/GPS 6600A
5.18 To Start
See Graphic: wc_gr002500
Before starting, be sure you read and understand all the safety and
operating instructions in this manual.
5.18.1 Disconnect all loads from the generator and place the main circuit
breaker switch in the OFF position (a2).
5.18.2 Set the auto idle switch to “OFF” (c).
5.18.3 Open the fuel valve (d1).
Note: If the engine is cold, move the choke lever to the closed position
(e2). If the engine is warm, set the choke lever to the open position
(e1).
5.18.4 On recoil start engines, turn the engine switch to “ON” (b1) and pull the
starter rope (f).
5.18.5 On electric start engines, press the ignition switch (k) and hold until the
engine starts. Release the switch after the engine starts.
NOTICE: DO NOT run the starter motor more than 5 seconds at a time
or damage to the starter motor may occur. If the engine fails to start,
release the switch and wait 10 seconds to let the starter motor cool
before trying again.
Note: If the oil level in the engine is low, the engine will not start. If this
happens, check the oil level and add oil as needed.
5.18.6 As the engine warms up, move the choke lever to the OPEN position
(e1).
5.18.7 Allow the engine to warm up for a few minutes before placing the main
breaker in the "ON" position (a1) and attaching loads.
34
GP/GPS 6600A
Operation
5.19 To Stop
See Graphic: wc_gr002500
5.19.1
Turn off and disconnect all tools and appliances attached to the
generator.
5.19.2
Place the main circuit breaker in the OFF position (a2).
5.19.3
Turn the engine switch to “OFF” (b2).
5.19.4
Close the fuel valve (d2).
Note: To stop the engine quickly in an emergency, turn or press the
engine switch to “OFF” (b2).
35
Maintenance
6.
GP/GPS 6600A
Maintenance
6.1
Engine Maintenance
The chart below lists basic machine and engine maintenance. Refer to
the engine manufacturer’s Operator’s Manual for additional
information on engine maintenance.
6.2
Periodic Maintenance Schedule
Daily
before
starting
Check the fuel level.
„
Check the engine oil level.
„
Inspect the air filter. Replace as
needed.
„
Check external hardware.
„
After
first
20 hrs.
Clean the air cleaner element.*
Every
50
hrs.
Every
100
hrs.
Every
300
hrs.
„
Inspect the shockmounts for damage.
„
Change the engine oil.*
„
„
Clean the sediment cup or fuel
strainer.
„
Check and clean the spark plug.
„
Check and adjust the valve clearance.
„
Clean the fuel tank.*
„
Check condition of the fuel line.
Replace when necessary.
„
*Service more frequently in dusty conditions.
36
GP/GPS 6600A
6.3
Maintenance
Engine Oil
See Graphic: wc_gr000022
6.3.1
Drain the oil while the engine is still warm.
6.3.2
Remove the oil filler plug (a) and the drain plug (b) to drain the oil.
Note: In the interests of environmental protection, place a plastic sheet
and a container under the machine to collect any liquid that drains off.
Dispose of this liquid in accordance with environmental protection
legislation.
6.3.3
Install the drain plug.
6.3.4
Fill the engine crankcase with the recommended oil up to the level of
the plug opening (c). See Technical Data for oil quantity and type.
6.3.5
Install the oil filler plug.
37
Maintenance
6.4
GP/GPS 6600A
Servicing Air Cleaner
See Graphic: wc_gr002815
Service the air cleaner frequently to prevent carburetor malfunction.
NOTICE: NEVER run the engine without the air cleaner. Severe
engine damage will occur.
NEVER use gasoline or other types of low flash-point solvents for
cleaning the air cleaner. A fire or explosion could result.
WARNING
To service:
6.4.1
Remove the air cleaner cover (a). Inspect the element (b) for holes or
tears. Replace the element if it is damaged.
6.4.2
Wash the foam element (b) in a solution of mild detergent and warm
water. Rinse it thoroughly in clean water. Allow the element to dry
thoroughly. Soak the element in clean engine oil and squeeze out
excess oil.
38
GP/GPS 6600A
6.5
Maintenance
Spark Plug
See Graphic: wc_gr000028
Clean or replace the spark plug as needed to ensure proper operation.
Refer to the engine owner’s manual.
The muffler becomes very hot during operation and remains hot for a
while after stopping the engine. Do not touch the muffler while it is hot.
WARNING
Note: Refer to the Technical Data for the recommended spark plug
type and the electrode gap setting.
6.5.1
Remove the spark plug and inspect it.
6.5.2
Replace the spark plug if the insulator is cracked or chipped.
6.5.3
Clean the spark plug electrodes with a wire brush.
6.5.4
Set the electrode gap (a).
6.5.5
Tighten the spark plug securely.
NOTICE: A loose spark plug can become very hot and may cause
engine damage.
39
Maintenance
6.6
GP/GPS 6600A
Cleaning the Sediment Cup
See Graphic: wc_gr000029
6.7
6.6.1
Turn the fuel valve off.
6.6.2
Remove the sediment cup (a) and the O-ring (b).
6.6.3
Wash both thoroughly in a nonflammable solvent. Dry and reinstall
them.
6.6.4
Turn the fuel valve on and check for leaks.
Carburetor Adjustment
See Graphic: wc_gr000032
6.7.1
Start the engine and allow it to warm up to operating temperature.
6.7.2
Set the pilot screw (a) two turns out. See Note.
6.7.3
With the engine idling, turn the pilot screw (a) in or out to the setting
that produces the highest rpm.
6.7.4
After the pilot screw is adjusted, turn the throttle stop screw (b) to
obtain the standard idle speed. See Technical Data.
Note: On some engines the pilot screw is fitted with a limiter cap (c)
to prevent excessive enrichment of the air-fuel mixture in order to
comply with emission regulations. The mixture is set at the factory and
no adjustment should be necessary. Do not attempt to remove the
limiter cap. The limiter cap cannot be removed without breaking the
pilot screw.
40
GP/GPS 6600A
6.8
Maintenance
Adjusting Engine Speed
See Graphic: wc_gr000032
Generators require a fixed engine speed to maintain the correct
voltage. Engine speed is controlled by a governor which automatically
adjusts to varying loads on the engine to maintain a constant speed.
There is no throttle control.
To set the engine to the proper speed:
Turn the speed adjusting screw (b) in or out to obtain a no-load speed.
See Technical Data.
NOTICE: Setting the engine speed too high or too low may damage
tools and other appliances attached to the generator.
41
Maintenance
6.9
GP/GPS 6600A
Storage
Before storing the generator for a long period of time:
6.9.1
Close the fuel valve and remove and empty the sediment cup or fuel
strainer.
6.9.2
Disconnect the fuel line from the carburetor. Place open end of fuel line
into a suitable container and open fuel valve to drain fuel from tank.
WARNING
Gasoline is extremely flammable. Drain the fuel tank in a wellventilated area. DO NOT drain the fuel tank in an area with flames or
sparks.
6.9.3
Loosen the drain screw on the carburetor and drain any remaining fuel
from the carburetor.
6.9.4
Change the engine oil.
6.9.5
Remove the spark plug and pour approximately 30 ml (1 ounce) of
clean engine oil into the cylinder. Crank the engine a few turns to
distribute the oil to the inside of the cylinder walls.
6.9.6
Pull the starter rope slowly until resistance is felt and leave the handle
in this position. This ensures that the intake and exhaust valves are
closed.
6.9.7
Store the generator in a clean, dry area.
6.10 Transport
Let the engine cool before transporting the generator or storing
indoors, to avoid burns or fire hazards.
WARNING
When transporting the generator:
6.10.1 Turn the engine fuel valve to the OFF position.
6.10.2 Position the generator level to prevent fuel from spilling.
6.10.3 Secure the generator by tying it down with a suitable rope.
WARNING
When transporting the machine by hand, be sure to employ manpower
commensurate with the weight of the machine. To avoid back injury
when lifting the machine, bend the knees to pick it up rather than
bending your back only.
42
GP/GPS 6600A
Maintenance
6.11 Troubleshooting
Problem / Symptom
Reason / Remedy
If engine doesn't start, check
that:
• Engine switch is on "Start".
• Fuel valves under fuel tank and on engine are open.
• Fuel tank has fuel.
• Choke lever is in correct position. Choke should be
closed when starting a cold engine.
• All loads are disconnected from generator.
• Spark plug is in good condition.
• Spark plug cap is tight.
• Engine oil level is adequate.
If engine starts but there is no
power at receptacles, check
that:
• Circuit breaker is closed.
If engine starts but runs erratically, check that:
• Hose routing from the fuel tank to the engine is correct. For proper operation, the hose must run
through the bushing in the lifting bracket. Refer to
the Parts Book for illustration.
• Connector from generator to control panel is tight.
6.12 Wire Colors
Wire Colors
B
Black
R
Red
Y
Yellow
Or
Orange
G
Green
T
Tan
Br
Brown
Pr
Purple
L
Blue
V
Violet
Cl
Clear
Sh
Shield
P
Pink
W
White
Gr
Gray
LL
Light blue
43
Maintenance
GP/GPS 6600A
6.13 Electrical Schematic
Ref.
Description
Ref.
Description
A
Generator
C
Engine
B
Control box
D
Electric start engines
Ref.
Description
Ref.
Description
1
Main stator winding 1
11
Capacitor
2
Main stator winding 2
12
Engine ON / OFF switch
3
Auto idle unit
13
Rectifier
4
Main circuit breaker
14
Rotor winding/brushes
5
Voltage selector switch
(120/240V position shown)
15
Secondary (excitation) winding
6
GFI duplex receptacle—120V
16
DC winding
7
Twist-lock receptacle—120V
17
Automatic voltage regulator (AVR)
8
Twist-lock receptacle—120/240V
18
15A fuse (GPS only)
9
Auto idle switch
19
Ignition switch (GPS only)
10
5A fuse
44
GP/GPS 6600A
Maintenance
45
Maintenance
GP/GPS 6600A
6.14 Electrical Schematic (CAN models only)
Ref.
Description
Ref.
Description
A
Generator
C
Engine
B
Control box
D
Electric start engines
Ref.
Description
Ref.
Description
1
Main stator winding 1
12
Engine ON / OFF switch
2
Main stator winding 2
13
Rectifier
3
Auto idle unit
14
Rotor winding/brushes
4
Main circuit breaker
15
Secondary (excitation) winding
5
Voltage selector switch
(120V/240V position shown)
16
DC winding
6
GFI duplex receptacle—120V
17
Automatic voltage regulator (AVR)
7
Twist-lock receptacle—120V
18
15A fuse (GPS only)
8
Twist-lock receptacle—120/240V
19
Ignition switch (GPS only)
9
Auto idle switch
21
20A circuit breaker
10
5A fuse
22
20A circuit breaker
(GP 3800 CAN only)
11
Capacitor
23
30A circuit breaker
(GP 5600/6600 CAN only)
46
GP/GPS 6600A
Maintenance
47
Maintenance
GP/GPS 6600A
6.15 Engine Schematic
See Graphic: wc_gr002580
Ref.
Description
Ref.
Description
A
Generator
D
Wacker Engine
B
Control box
E
Honda Engine
C
Electric start engines (GPS)
Ref.
Description
Ref.
1
Idle solenoid
6
Solenoid (GPS only)
2
Fuel cut solenoid
7
Starter (GPS only)
3
Oil alert module
8
Charging coil (GPS only)
4
Oil level switch
9
Battery (GPS only)
5
Coil
48
Description
GP/GPS 6600A
Maintenance
49
Maintenance
GP/GPS 6600A
Notes
50
Wacker Construction Equipment AG
·
Preußenstraße 41
· D-80809 München
· Tel.: +49-(0)89-3 54 02 - 0 · Fax: +49 - (0)89-3 54 02-3 90
Wacker Corporation · P.O. Box 9007 · Menomonee Falls, WI 53052-9007 · Tel. : (262) 255-0500 · Fax: (262) 255-0550 · Tel. : (800) 770-0957
Wacker Asia Pacific Operations · Skyline Tower, Suite 2303, 23/F · 39 Wang Kwong Road, Kowloon Bay, Hong Kong · Tel. +852 2406 60 32 · Fax: +852 2406 60 21