HP Pavilion DV6007 Specifications

Maintenance and Service
Guide
HP Pavilion dv6000 Notebook PC
Document Part Number: 416618-001
July 2006
This guide is a troubleshooting reference used for maintaining
and servicing the computer. It provides comprehensive
information on identifying computer features, components, and
spare parts; troubleshooting computer problems; and performing
computer disassembly procedures.
© Copyright 2006 Hewlett-Packard Development Company, L.P.
Microsoft and Windows are U.S. registered trademarks of
Microsoft Corporation. AMD, Sempron, Turion, and combinations thereof
are trademarks of Advanced Micro Devices, Inc. Bluetooth is a trademark
owned by its proprietor and used by Hewlett-Packard Company under
license.
The information contained herein is subject to change without notice. The
only warranties for HP products and services are set forth in the express
warranty statements accompanying such products and services. Nothing
herein should be construed as constituting an additional warranty. HP shall
not be liable for technical or editorial errors or omissions contained herein.
Maintenance and Service Guide
HP Pavilion dv6000 Notebook PC
First Edition: July 2006
Document Part Number: 416618-001
Contents
1 Product Description
1.1
1.2
1.3
1.4
1.5
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–2
Resetting the Computer. . . . . . . . . . . . . . . . . . . . . . . 1–4
Power Management. . . . . . . . . . . . . . . . . . . . . . . . . . 1–4
External Components . . . . . . . . . . . . . . . . . . . . . . . . 1–5
Design overview . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–20
2 Troubleshooting
2.1
2.2
2.3
2.4
Setup Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the Setup Utility . . . . . . . . . . . . . . . . . . . . . . .
Setup Utility Menus . . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting Flowcharts . . . . . . . . . . . . . . . . . . .
Maintenance and Service Guide
2–1
2–2
2–6
2–9
iii
Contents
3 Illustrated Parts Catalog
3.1
3.2
3.3
3.4
3.5
3.6
3.7
Serial Number Location . . . . . . . . . . . . . . . . . . . . . . 3–1
Computer Major Components. . . . . . . . . . . . . . . . . . 3–2
Display Assembly Components . . . . . . . . . . . . . . . 3–16
Mass Storage Devices . . . . . . . . . . . . . . . . . . . . . . . 3–18
Plastics Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–19
Miscellaneous . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–20
Sequential Part Number Listing . . . . . . . . . . . . . . . 3–22
4 Removal and Replacement Preliminaries
4.1 Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2 Service Considerations . . . . . . . . . . . . . . . . . . . . . . .
Plastic Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cables and Connectors . . . . . . . . . . . . . . . . . . . . . . .
4.3 Preventing Damage to Removable Drives . . . . . . . .
4.4 Preventing Electrostatic Damage . . . . . . . . . . . . . . .
4.5 Packaging and Transporting Precautions . . . . . . . . .
4.6 Workstation Precautions . . . . . . . . . . . . . . . . . . . . . .
4.7 Grounding Equipment and Methods . . . . . . . . . . . . .
iv
4–1
4–2
4–2
4–2
4–3
4–4
4–5
4–6
4–7
Maintenance and Service Guide
Contents
5 Removal and Replacement Procedures
5.1 Serial Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–1
5.2 Disassembly Sequence Chart . . . . . . . . . . . . . . . . . . 5–2
5.3 Preparing the Computer For Disassembly . . . . . . . . 5–4
5.4 Hard Drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–6
5.5 Computer Feet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–9
5.6 Memory Module . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–10
5.7 RTC Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–12
5.8 Mini Card Module. . . . . . . . . . . . . . . . . . . . . . . . . . 5–13
5.9 Optical Drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–16
5.10 Switch Cover. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–18
5.11 Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–20
5.12 Speaker Assembly. . . . . . . . . . . . . . . . . . . . . . . . . 5–23
5.13 Power Button Board . . . . . . . . . . . . . . . . . . . . . . . 5–24
5.14 Display Assembly . . . . . . . . . . . . . . . . . . . . . . . . . 5–26
5.15 Top Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–39
5.16 Audio Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–44
5.17 Bluetooth Module . . . . . . . . . . . . . . . . . . . . . . . . . 5–46
5.18 ExpressCard Assembly . . . . . . . . . . . . . . . . . . . . . 5–48
5.19 USB/Power Connector Board . . . . . . . . . . . . . . . . 5–50
5.20 System Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–52
5.21 Fan/Heat Sink Assembly. . . . . . . . . . . . . . . . . . . . 5–56
5.22 Processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–59
Maintenance and Service Guide
v
Contents
6 Specifications
A Screw Listing
B Backup and Recovery
C Display Component Recycling
D Connector Pin Assignments
E Power Cord Set Requirements
Index
vi
Maintenance and Service Guide
1
Product Description
The HP Pavilion dv6000 Notebook PC offers advanced
modularity, AMD Turion™ 64 Mobile Technology and
Mobile AMD Sempron™ processors, and extensive multimedia
support.
HP Pavilion dv6000 Notebook PC
Maintenance and Service Guide
1–1
Product Description
1.1 Features
■
The following processors are available, varying by
computer model:
❏ AMD Turion ML-56 1.80-GHz
❏ AMD Turion ML-52 1.60-GHz
❏ AMD Turion ML-50 1.60-GHz
❏ Mobile AMD Sempron 3400+ (1.80-GHz)
❏ Mobile AMD Sempron 3200+ (1.60-GHz)
1–2
■
15.4-inch WXGA (1280 × 768) TFT display with over
16.7 million colors, varying by computer model
■
120-, 100-, 80-, or 60-GB high-capacity hard drive, varying
by computer model
■
256-MB DDR synchronous DRAM (SDRAM) at 667 MHz,
expandable to 2.0 GB
■
Microsoft® Windows® XP Home Edition or Windows XP
Professional, or Free DOS, varying by computer model
■
Full-size Windows keyboard with embedded numeric keypad
■
TouchPad pointing device with on/off button and dedicated
two-way scroll zone
■
Integrated 10/100 BASE-T Ethernet local area network
(LAN) network interface card (NIC) with RJ-45 jack
■
Integrated high-speed 56K modem with RJ-11 jack
■
Integrated wireless support for Mini Card IEEE 802.11b and
802.11b/g WLAN device
■
Support for ExpressCard
Maintenance and Service Guide
Product Description
■
External 90- or 65-watt AC adapter with 3-wire power cord
■
6-cell or 12-cell Li-Ion battery
■
Stereo speakers with volume up and down buttons
■
Integrated microphones (select models only)
■
Support for the following optical drives:
❏ DVD±RW/R and CD-RW Double-Layer Combo Drive
with LightScribe
❏ DVD±RW/R and CD-RW Double-Layer Combo Drive
❏ DVD/CD-RW Combo Drive
■
Connectors:
❏ Audio-in (microphone)
❏ Audio-out (headphone)
❏ Consumer infrared lens
❏ Docking (select models only)
❏ ExpressCard
❏ External monitor
❏ IEEE 1394 digital (select models only)
❏ Digital Media Slot (select models only)
❏ Power
❏ RJ-11 (modem)
❏ RJ-45 (network)
❏ S-Video-out (select models only)
❏ Universal Serial Bus (USB) v. 2.0
Maintenance and Service Guide
1–3
Product Description
1.2 Resetting the Computer
If the computer you are servicing has an unknown password,
follow these steps to clear the password. These steps also
clear CMOS:
1. Prepare the computer for disassembly (refer to Section 5.3,
“Preparing the Computer For Disassembly,” for more
information).
2. Remove the real-time clock (RTC) battery (refer to
Section 5.7, “RTC Battery,” for more information).
3. Wait approximately 5 minutes.
4. Replace the RTC battery and reassemble the computer.
5. Connect AC power to the computer. Do not reinsert any
batteries at this time.
6. Turn on the computer.
All passwords and all CMOS settings have been cleared.
1.3 Power Management
The computer comes with power management features that
extend battery operating time and conserve power. The
computer supports the following power management features:
1–4
■
Standby
■
Hibernation
■
Setting customization by the user
■
Hotkeys for setting the level of performance
■
Battery calibration
■
Lid switch standby/resume
■
Power button
■
Advanced Configuration and Power Management (ACPM)
compliance
Maintenance and Service Guide
Product Description
1.4 External Components
The external components on the front of the computer are shown
below and described in Table 1-1.
Front Components
Table 1-1
Front Components
Item
Component
Function
1
Power light
On: The computer is on.
Blinking: The computer is in standby.
Off: The computer is off or in hibernation.
2
Battery light
On: A battery is charging.
Blinking: A battery that is the only available
power source has reached a low-battery
condition. When the battery reaches a
critical low-battery condition, the battery
light begins blinking rapidly.
Off: If the computer is plugged into an
external power source, the light is turned off
when all batteries in the computer are fully
charged. If the computer is not plugged into
an external power source, the light stays off
until the battery reaches a low-battery
condition.
Maintenance and Service Guide
1–5
Product Description
Table 1-1
Front Components (Continued)
Item
Component
Function
3
Drive light
Blinking: The hard drive or optical drive is
being accessed.
4
Wireless switch
Turns the wireless feature on or off, but
does not create a wireless connection.
wireless network must be set up to
✎ Aestablish
a wireless connection.
5
Wireless light
Blue: An integrated wireless device, such
as a wireless local area network (LAN)
device and/or a Bluetooth® device, is
turned on.
Amber: All wireless devices are turned off.
6
Consumer infrared
lens (select models
only)
Receives a signal from the HP Remote
Control.
7
Audio-in
(microphone) jack
Connects an optional computer headset
microphone, stereo array microphone, or
monaural microphone.
8
Audio-out
(headphone) jack
Provides sound when connected to optional
powered stereo speakers, headphones,
ear buds, a headset, or television audio.
Audio-out
(headphone) S/PDIF
jack (select models
only)
Provides enhanced audio performance,
including surround sound and other
high-end audio output.
1–6
Maintenance and Service Guide
Product Description
The external components on the left side of the computer are
shown below and described in Table 1-2.
Left-Side Components
Table 1-2
Left-Side Components
Item
Component
Function
1
Security cable slot
Attaches an optional security cable to the
computer.
security cable is designed to act
✎ The
as a deterrent, but it may not prevent
the computer from being mishandled
or stolen.
2
S-Video-out jack
Connects an optional S-Video device such
as a television, VCR, camcorder, overhead
projector, or video capture card.
3
External monitor port
Connects an external VGA monitor or
projector.
Maintenance and Service Guide
1–7
Product Description
Table 1-2
Left-Side Components (Continued)
Item
Component
Function
4
Expansion port 3
Connects the computer to an optional
expansion product.
computer has only one
✎ The
expansion port. The term expansion
port 3 describes the type of
expansion port.
5
RJ-45 (network) jack
Connects a network cable.
select computer models, the
✎ On
network jack provides Gigabit
Ethernet functionality.
6
RJ-11 (modem) jack
Connects a modem cable.
7
HDMI port (select
models only)
Connects an optional audio or video device
such as a high definition television, set-top
box, DVD player, or any compatible digital
or audio device.
8
USB ports (2)
Connect optional USB devices.
9
1394 port (select
models only)
Connects an optional IEEE 1394 or 1394a
device, such as a camcorder.
10
Digital Media Slot
(select models only)
Supports the following optional digital card
formats: Secure Digital (SD) Memory Card,
MultiMediaCard (MMC), Secure Digital
Input/Output (SD I/O), Memory Stick (MS),
Memory Stick Pro (MSP), xDPicture Card
(XD), xD-Picture Card (XD) Type M.
1–8
Maintenance and Service Guide
Product Description
The external components on the right side of the computer
are shown below and described in Table 1-3.
Right-Side Components
Table 1-3
Right-Side Components
Item
Component
Function
1
ExpressCard slot
Supports optional ExpressCard/54 cards.
2
Optical drive
Reads an optical disc.
3
USB port (select
models only)
Connects an optional USB device.
4
Power connector
Connects an AC adapter.
Maintenance and Service Guide
1–9
Product Description
The computer keyboard components are shown below and
described in Table 1-4.
Keyboard Components
1–10
Maintenance and Service Guide
Product Description
Table 1-4
Keyboard Components
Item
Component
Function
1
Function keys
Execute frequently used system functions
when pressed in combination with the
fn key.
2
caps lock key
Enables caps lock and turns on the caps
lock light.
3
fn key
Executes frequently used system
functions when pressed in combination
with a function key or the esc key.
4
Windows logo key
Displays the Microsoft Windows Start
menu.
5
Windows
applications key
Displays a shortcut menu for items
beneath the pointer.
6
Arrow keys
Move the cursor around the screen.
7
Embedded numeric
keypad keys
Can be used like the keys on an external
numeric keypad.
8
num lock key
Enables numeric lock, turns on the
embedded numeric keypad, and turns
on the num lock light.
Maintenance and Service Guide
1–11
Product Description
The computer top components are shown below and described in
Table 1-5.
Top Components, Part 1
1–12
Maintenance and Service Guide
Product Description
Table 1-5
Top Components, Part 1
Item
Component
Function
1
Integrated camera
(select models only)
Records video and captures still photos.
2
Internal microphones
(2, select models only)
Record sound.
microphone icon next to each
✎ Amicrophone
opening indicates that
the computer has internal
microphones.
3
Speakers (2)
Produce sound.
4
Power button
When the computer is
■
■
■
■
Off, press to turn on the computer.
On, press to enter hibernation.
In standby, briefly press to exit standby.
In hibernation, briefly press to
exit hibernation.
If the computer has stopped responding
and Microsoft® Windows® shutdown
procedures cannot be used, press and hold
the power button for at least 5 seconds to
turn off the computer.
5
Caps lock light
On: Caps lock is on.
6
Volume mute button
Mutes and restores speaker sound.
7
Volume scroll zone
Adjusts speaker volume. Slide your finger
to the left to decrease volume and to the
right to increase volume. You can also tap
the minus sign on the scroll zone to
decrease volume, or tap the plus sign on
the scroll zone to increase volume.
8
Num lock light
On: Num lock is on or the embedded
numeric keypad is enabled.
Maintenance and Service Guide
1–13
Product Description
The computer top components are shown below and described in
Table 1-6.
Top Components, Part 2
1–14
Maintenance and Service Guide
Product Description
Table 1-6
Top Components, Part 2
Item
Component
Function
1
Media button
If QuickPlay is not installed and the
computer is
■ On, opens the music program or Media
menu, which allows you to select a
multimedia program.
■ Off, does not function.
■ In standby, resumes from standby into
Windows.
If QuickPlay is installed and the computer is
■ On, opens the music program or Media
menu, which allows you to select a
multimedia program.
■ Off, opens the music program or the
Media menu, which allows you to select
a multimedia program.
■ In standby, resumes from standby into
Windows.
media button does not affect the
✎ The
procedure for restoring from
hibernation.
2
DVD button
When the computer is
opens the default DVD program
✎ On,
to start a DVD in the optical drive.
opens QuickPlay to start a DVD
✎ Off,
in the optical drive. If the QuickPlay
software is not installed, the DVD
button starts in Windows.
opens QuickPlay to
✎ Instarthibernation,
a DVD in the optical drive. If
QuickPlay is not installed, the
computer resumes from hibernation.
Maintenance and Service Guide
1–15
Product Description
Table 1-6
Top Components, Part 2 (Continued)
Item
Component
Function
3
Previous/rewind
button
When a disc is playing in the optical drive:
■ Plays the previous track or chapter,
when pressed once.
■ Rewinds when pressed with the fn key.
4
Play/pause button
When a disc is in the optical drive and is
■ Not playing, plays the disc.
■ Playing, pauses the disc.
5
Next/fast forward
button
When a disc is playing in the optical drive:
■ Play the next track or chapter, when
pressed once.
■ Fast forwards when pressed with the
fn key.
6
Stop button
When a disc is playing in the optical drive,
stops the current disc activity.
1–16
Maintenance and Service Guide
Product Description
The computer TouchPad components are shown below and
described in Table 1-7.
TouchPad Components
Table 1-7
Touchpad Components
Item
Component
Function
1
TouchPad light
Blue: TouchPad is enabled.
Amber: TouchPad is disabled.
2
TouchPad
Moves the pointer and selects or activates
items on the screen.
3
Left and right
TouchPad buttons
Function like the left and right buttons on an
external mouse.
4
TouchPad on/off
button
Enables/disables the TouchPad.
5
TouchPad vertical
scroll zone
Scrolls up or down.
Maintenance and Service Guide
1–17
Product Description
The external components on the bottom of the computer
are shown below and described in Table 1-8.
Bottom Components
Table 1-8
Bottom Components
Item
Component
Function
1
Battery bay
Holds the battery.
2
Battery release latch
Releases the battery from the
battery bay.
3
Optical drive
Reads an optical disc.
1–18
Maintenance and Service Guide
Product Description
Table 1-8
Bottom Components (Continued)
Item
Component
Function
4
Memory module
compartment
Contains the memory module slots, the
Mini Card slot, and the RTC battery.
5
Vents (5)
Enable airflow to cool internal
components.
Ä
To prevent overheating, do not
obstruct vents. Use the computer
only on a hard, flat surface. Do
not allow another hard surface,
such as an adjoining optional
printer, or a soft surface, such as
pillows or thick rugs or clothing, to
block airflow.
computer fan starts up
✎ The
automatically to cool internal
components and prevent
overheating. It is normal for the
internal fan to cycle on and off
during routine operation.
6
Hard drive bay
Maintenance and Service Guide
Holds the hard drive.
1–19
Product Description
1.5 Design overview
This section presents a design overview of key parts and features
of the computer. Refer to Chapter 3, “Illustrated Parts Catalog,”
to identify replacement parts, and Chapter 5, “Removal and
Replacement Procedures,” for disassembly steps.
The system board provides the following device connections:
Ä
■
AMD Turion and Mobile AMD Sempron processors
■
Audio
■
Display
■
ExpressCard
■
Fan
■
Hard drive
■
Keyboard and TouchPad
■
Memory module
■
Mini Card module
CAUTION: To properly ventilate the computer, allow at least a 7.6-cm
(3-inch) clearance on the left and right sides of the computer.
The computer uses an electric fan for ventilation. The fan is
controlled by a temperature sensor and is designed to turn on
automatically when high temperature conditions exist. These
conditions are affected by high external temperatures, system
power consumption, power management/battery conservation
configurations, battery fast charging, and software. Exhaust air is
displaced through the ventilation grill located on the left side of
the computer.
1–20
Maintenance and Service Guide
2
Troubleshooting
Å
WARNING: Only authorized technicians trained by HP should repair
this equipment. All troubleshooting and repair procedures are detailed
to allow only subassembly-/module-level repair. Because of the
complexity of the individual boards and subassemblies, do not attempt
to make repairs at the component level or modifications to any printed
wiring board. Improper repairs can create a safety hazard. Any
indication of component replacement or printed wiring board
modification may void any warranty or exchange allowances.
2.1 Setup Utility
The Setup Utility is a ROM-based information and customization
utility that can be used even when your Windows operating
system is not working or will not load.
The utility reports information about the computer and provides
settings for startup, security, and other preferences.
1. Turn on or restart the computer in Windows.
2. Before Windows opens and while the “Press <F10> to enter
setup” prompt is displayed in the lower-left corner of the
screen, press f10.
Maintenance and Service Guide
2–1
Troubleshooting
2.2 Using the Setup Utility
Changing the Language of the Setup Utility
The following procedure explains how to change the language of
the Setup Utility. If the computer is not in the Setup Utility, begin
at step 1. If the computer is in the Setup Utility, begin at step 2.
1. To open the Setup Utility, turn on or restart the computer in
Windows, and then press f10 while the prompt, “Press <F10>
to enter setup,” is displayed in the lower-left corner of the
screen.
2. Use the arrow keys to select System Configuration >
Language, and then press enter.
3. Press f5 or f6 (or use the arrow keys) to select a language, and
then press enter to select a language.
4. When a confirmation prompt with your preference selected is
displayed, press enter to save your preference.
5. To set your preferences and exit the Setup Utility, press f10
and then follow the instructions on the screen.
Your preferences go into effect when the computer restarts in
Windows.
2–2
Maintenance and Service Guide
Troubleshooting
Navigating and Selecting in the Setup Utility
Because the Setup Utility is not Windows-based, it does not
support the TouchPad. Navigation and selection are by keystroke.
■
To choose a menu or a menu item, use the arrow keys.
■
To choose an item in a drop-down list or to toggle a field, for
example an Enable/Disable field, use either the arrow keys or
f5 or f6.
■
To select an item, press enter.
■
To close a text box or return to the menu display, press f1.
■
To display additional navigation and selection information
while the Setup Utility is open, press f1.
Displaying System Information
The following procedure explains how to display system
information in the Setup Utility. If the Setup Utility is not open,
begin at step 1. If the Setup Utility is open, begin at step 2.
1. To open the Setup Utility, turn on or restart the computer in
Windows, and then press f10 while the prompt, “Press <F10>
to enter setup,” is displayed in the lower-left corner of the
screen.
2. Access the system information by using the Main menu.
3. To close the Setup Utility without changing any settings, use
the arrow keys to select Exit > Exit Discarding Changes,
and then press enter. (The computer restarts in Windows.)
Maintenance and Service Guide
2–3
Troubleshooting
Restoring Default Settings in the
Setup Utility
The following procedure explains how to restore the Setup Utility
default settings. If the computer is not in the Setup Utility, begin
at step 1. If the computer is in the Setup Utility, begin at step 2.
1. To open the Setup Utility, turn on or restart the computer in
Windows, and then press f10 while the prompt, “Press <F10>
to enter setup,” is displayed in the lower-left corner of the
screen.
2. Select Exit > Load Setup Defaults, and then press f10.
3. When the Setup Confirmation is displayed, press enter to save
your preferences.
4. To set your preferences and exit the Setup Utility, press f10,
and then follow the instructions on the screen.
The Setup Utility default settings are set when you exit the Setup
Utility and go into effect when the computer restarts.
password, security, and language settings are not
✎ Your
changed when you restore the factory default settings.
Using Advanced Setup Utility Features
This guide describes the Setup Utility features recommended for
all users. For more information about the Setup Utility features
recommended for advanced users only, refer to the Help and
Support Center, which is accessible only when the computer is in
Windows.
The Setup Utility features available for advanced users include a
hard drive self-test, a Network Service Boot, and settings for boot
order preferences.
2–4
Maintenance and Service Guide
Troubleshooting
The “<F12> to boot from LAN” message that is displayed in the
lower-left corner of the screen each time the computer is started
or restarted in Windows or restored from hibernation is the
prompt for a Network Service Boot.
The “Press <ESC> to change boot order” message that is
displayed in the lower-left corner of the screen each time the
computer is started or restarted in Windows or restored from
hibernation is the prompt to change the boot order.
Closing the Setup Utility
You can close the Setup Utility with or without saving changes.
■
To close the Setup Utility and save your changes from the
current session, use either of the following procedures:
❏ Press f10, and then follow the instructions on the screen.
– or –
❏ If the Setup Utility menus are not visible, press esc to
return to the menu display. Then use the arrow keys to
select Exit > Exit Saving Changes, and then press enter.
When you use the f10 procedure, you are offered an option
to return to the Setup Utility. When you use the Exit
Saving Changes procedure, the Setup Utility closes when
you press enter.
■
To close the Setup Utility without saving your changes from
the current session:
If the Setup Utility menus are not visible, press esc to return
to the menu display. Then use the arrow keys to select Exit >
Exit Discarding Changes, and then press enter.
After the Setup Utility closes, the computer restarts in Windows.
Maintenance and Service Guide
2–5
Troubleshooting
2.3 Setup Utility Menus
The menu tables in this section provide an overview of Setup
Utility options.
of the Setup Utility menu listed in this chapter may not
✎ Some
be supported by your computer.
Selecting from the Main Menu
Table 2-1
Main Menu
Select
To Do This
System Information
■
■
■
View and change the system time and date.
View identification information about the
computer.
View specification information about the
processor, memory size, system BIOS, and
keyboard controller version (select models
only).
Selecting from the Security Menu
Table 2-2
Security Menu
Select
To Do This
Administrator password
Enter, change, or delete an administrator
password.
Power-on password
Enter, change, or delete a power-on password.
2–6
Maintenance and Service Guide
Troubleshooting
Selecting from the System
Configuration Menu
Table 2-3
System Configuration Menu
Select
To Do This
Language Support
Change the Setup Utility language.
Embedded WLAN Device
Radio
Enable/disable an embedded wireless LAN
device.
Embedded Bluetooth
Device (select models only)
Enable/disable an embedded Bluetooth device
(select models only).
Enhanced SATA support
(select models only)
Enable/disable enhanced SATA mode.
Boot Options
Set the following boot options:
■ f10 and f12 Delay (sec.)—Set the delay for the
f10 and f12 functions of the Setup Utility in
intervals of 5 seconds each (0. 5, 10, 15, 20).
■ CD-ROM boot—Enable/disable boot from
CD-ROM.
■ Floppy boot—Enable/disable boot from Floppy.
■ Internal Network Adapter boot—Enable/disable
boot from Internal Network Adapter.
■ Boot Order—Set the boot order for:
❐ USB Floppy
❐ ATAPI CD/DVD ROM Drive
❐ Hard drive
❐ USB Diskette on Key
❐ USB Hard drive
❐ Network adapter
Maintenance and Service Guide
2–7
Troubleshooting
Selecting from the Diagnostics Menu
Table 2-4
Diagnostics Menu
Select
To Do This
Hard Disk Self Test
Run a comprehensive self-test on the hard drive.
models with two hard drives, this menu
✎ On
option is called the Primary Hard Disk Self
Test.
Secondary Hard Disk Self
Test (select models only)
2–8
Run a comprehensive self-test on a secondary
hard drive.
Maintenance and Service Guide
Troubleshooting
2.4 Troubleshooting Flowcharts
Table 2-5
Troubleshooting Flowcharts Overview
Flowchart
Description
2.1
“Flowchart 2.1—Initial Troubleshooting”
2.2
“Flowchart 2.2—No Power, Part 1”
2.3
“Flowchart 2.3—No Power, Part 2”
2.4
“Flowchart 2.4—No Power, Part 3”
2.5
“Flowchart 2.5—No Power, Part 4”
2.6
“Flowchart 2.6—No Video, Part 1”
2.7
“Flowchart 2.7—No Video, Part 2”
2.8
“Flowchart 2.8—Nonfunctioning Docking Device (if applicable)”
2.9
“Flowchart 2.9—No Operating System (OS) Loading”
2.10
“Flowchart 2.10—No OS Loading, Hard Drive, Part 1”
2.11
“Flowchart 2.11—No OS Loading, Hard Drive, Part 2”
2.12
“Flowchart 2.12—No OS Loading, Hard Drive, Part 3”
2.13
“Flowchart 2.13—No OS Loading, Diskette Drive”
Maintenance and Service Guide
2–9
Troubleshooting
Table 2-5
Troubleshooting Flowcharts Overview (Continued)
Flowchart
Description
2.14
“Flowchart 2.14—No OS Loading, Optical Drive”
2.15
“Flowchart 2.15—No Audio, Part 1”
2.16
“Flowchart 2.16—No Audio, Part 2”
2.17
“Flowchart 2.17—Nonfunctioning Device”
2.18
“Flowchart 2.18—Nonfunctioning Keyboard”
2.19
“Flowchart 2.19—Nonfunctioning Pointing Device”
2.20
“Flowchart 2.20—No Network/Modem Connection”
2–10
Maintenance and Service Guide
Troubleshooting
Flowchart 2.1—Initial Troubleshooting
Begin
troubleshooting.
N
Go to
Is there
power?
“Flowchart
2.2—No Power,
Part 1.”
Y
N
Check
LED board,
speaker
connections.
Beeps,
LEDs, or error
messages?
N
Y
Go to
All drives
working?
N
Go to
Is there video?
(no boot)
Y
“Flowchart
2.6—No Video,
Part 1.”
N
Keyboard/
pointing
device
working?
Y
N
Go to
Is the OS
loading?
N
Go to
Is there
sound?
Y
“Flowchart
2.9—No Operating
System (OS)
Loading.”
Y
“Flowchart
2.15—No Audio,
Part 1.”
Y
Maintenance and Service Guide
“Flowchart
2.17—Nonfunctioning Device.”
Go to
“Flowchart
2.18—Nonfunctioning Keyboard”
or “Flowchart
2.19—Nonfunctioning Pointing
Device.”
N
Connecting
to network
or modem?
Y
Go to
“Flowchart
2.20—No
Network/Modem
Connection.”
End
2–11
Troubleshooting
Flowchart 2.2—No Power, Part 1
No power
(power LED
is off).
Remove from
docking device
(if applicable).
N
N
Power up
on battery
power?
Go to
Power up
on battery
power?
Reset
power.*
“Flowchart
2.3—No Power,
Part 2.”
Y
Y
N
N
Power up
on AC
power?
Power up
on AC power?
Reset
power.*
Y
Go to
“Flowchart
2.4—No Power,
Part 3.”
Y
Y
Power up in
docking
device?
Done
*NOTES
1. On select models, there is a separate
reset button.
2. On select models, the computer can be
reset using the standby switch and either
the lid switch or the main power switch.
N
1. Reseat the power cables in the docking
device and at the AC outlet.
2. Ensure the AC power source is active.
3. Ensure that the power strip is working.
Y
Done
2–12
N
Power up
in docking
device?
Go to
“Flowchart
2.8—Nonfunctioning
Docking Device (if
applicable).”
Maintenance and Service Guide
Troubleshooting
Flowchart 2.3—No Power, Part 2
Continued from
“Flowchart
2.2—No Power,
Part 1.”
Visually check for
debris in battery
socket and clean
if necessary.
Y
Power on?
Done
N
Check battery by
recharging it,
moving it to
another computer,
or replacing it.
N
Replace
power supply
(if applicable).
Power on?
Y
N
Go to
Done
Power on?
“Flowchart
2.4—No Power,
Part 3.”
Y
Done
Maintenance and Service Guide
2–13
Troubleshooting
Flowchart 2.4—No Power, Part 3
Continued from
“Flowchart
2.3—No Power,
Part 2.”
Plug directly
into AC outlet.
Y
Power LED
on?
Done
N
Reseat AC adapter
in computer and
at power source.
Y
Done
Power on?
N
External
N
Try different
outlet.
Power outlet
active?
Y
Internal or
external AC
adapter?
Replace external
AC adapter.
N
Internal
Go to
“Flowchart
2.5—No Power,
Part 4.”
Replace
power cord.
Power on?
Y
Y
Done
Power on?
Done
N
2–14
Maintenance and Service Guide
Troubleshooting
Flowchart 2.5—No Power, Part 4
Continued from
“Flowchart
2.4—No Power,
Part 3.”
Open
computer.
Y
Loose or
damaged
parts?
N
Reseat loose
components and
boards and
replace damaged
items.
Close
computer and
retest.
N
Power on?
Y
Done
Replace the following items (if applicable). Check
computer operation after each replacement:
1. Internal DC-DC converter*
2. Internal AC adapter
3. Processor board*
4. System board*
*NOTE: Replace these items as a set to prevent
shorting out among components.
Maintenance and Service Guide
2–15
Troubleshooting
Flowchart 2.6—No Video, Part 1
No video.
Docking Device
Go to
Stand-alone
or docking
device?
*NOTE: To change from internal to
external display, use the hotkey
combination.
“Flowchart
2.7—No Video,
Part 2.”
Stand-alone
Internal or
external
display*?
Y
Adjust
brightness.
A
Adjust
brightness.
Press lid
switch to ensure
operation.
Y
Video OK?
Done
N
Internal
External
Video OK?
Y
Done
N
Video OK?
Done
N
Replace the following one at a time. Test after each replacement.
1. Cable between computer and computer display (if applicable)
2. Display
3. System board
Check for bent
pins on cable.
N
Video OK?
Y
Internal and
external
video OK?
Replace
system
board.
Y
Done
2–16
N
Try
another
display.
Done
Maintenance and Service Guide
Troubleshooting
Flowchart 2.7—No Video, Part 2
Continued from
“Flowchart
2.6—No Video,
Part 1.”
Remove
computer from
docking device,
if connected.
Adjust
display
brightness.
Check brightness
of external
monitor.
N
Y
Go to “A” in
“Flowchart
2.6—No Video,
Part 1.”
Video OK?
Y
Video OK?
Done
N
Check that computer is properly
seated in docking device,
for bent pins on cable,
and for monitor connection.
Try another
external
monitor.
Y
Video OK?
Y
Internal
and external
video OK?
Done
Done
N
N
Go to
Adjust external
monitor display.
Maintenance and Service Guide
“Flowchart
2.8—Nonfunctioning
Docking Device (if
applicable).”
2–17
Troubleshooting
Flowchart 2.8—Nonfunctioning Docking Device
(if applicable)
Nonfunctioning
docking device.
Reseat power
cord in docking
device and
power outlet.
Check voltage
setting on docking
device.
Reinstall
computer into
docking device.
Y
Reset monitor
cable connector at
docking device.
Docking
device
operating?
N
Y
Docking
device
operating?
N
Done
Done
Test replacement
docking device with
new computer.
Remove computer,
replace docking
device.
2–18
Maintenance and Service Guide
Troubleshooting
Flowchart 2.9—No Operating System (OS)
Loading
No OS
loading.*
Reseat power
cord in docking
device and
power outlet.
No OS loading from hard drive,
go to “Flowchart 2.10—No OS Loading,
Hard Drive, Part 1.”
No OS loading from diskette drive,
go to “Flowchart 2.13—No OS Loading,
Diskette Drive.”
No OS loading from optical drive,
go to “Flowchart 2.14—No OS Loading,
Optical Drive.”
No OS loading from network,
go to “Flowchart 2.20—No Network/Modem
Connection.”
*NOTE: Before beginning troubleshooting, always
check cable connections, cable ends, and drives
for bent or damaged pins.
Maintenance and Service Guide
2–19
Troubleshooting
Flowchart 2.10—No OS Loading, Hard Drive,
Part 1
OS not
loading from
hard drive.
Y
Nonsystem
disk message?
N
Go to
“Flowchart
2.11—No OS
Loading,
Hard Drive, Part 2.”
Reseat
external
hard drive.
Y
OS loading?
Done
N
N
Boot
from
CD?
N
Y
Boot
from
diskette?
Check the Setup
utility for correct
booting order.
Y
Change boot
priority through
the Setup Utility
and reboot.
N
Boot
from
hard drive?
N
Y
Boot
from
hard drive?
Done
Y
2–20
Go to
“Flowchart
2.13—No OS
Loading,
Diskette Drive.”
Go to
“Flowchart
2.17—Nonfunctioning
Device.”
Maintenance and Service Guide
Troubleshooting
Flowchart 2.11—No OS Loading, Hard Drive,
Part 2
Continued from
“Flowchart
2.10—No OS
Loading,
Hard Drive, Part 1.”
Reseat
hard drive.
N
1. Replace
hard drive.
2. Replace system
board.
Disc or
diskette in
drive?
Y
Y
Hard drive
accessible?
Done
N
Remove disc or
diskette and
reboot.
Run FDISK.
Y
Boot
from
hard drive?
N
Done
N
Hard drive
partitioned?
Y
N
Y
N
Go to
“Flowchart
2.13—No OS
Loading,
Diskette Drive.”
Boot
from diskette
drive?
Create partition,
and then format
hard drive to
bootable
C:\ prompt.
Hard drive
formatted?
Format hard drive
and bring to
a bootable
C:\ prompt.
Computer
booted?
Load OS using
Operating System disc
(if applicable).
Y
N
Y
Hard drive
accessible?
Y
Done
N
Go to
“Flowchart
2.12—No OS
Loading,
Hard Drive, Part 3.”
Maintenance and Service Guide
Go to
“Flowchart
2.12—No OS
Loading,
Hard Drive, Part 3.”
2–21
Troubleshooting
Flowchart 2.12—No OS Loading, Hard Drive,
Part 3
Continued from
“Flowchart
2.11—No OS
Loading,
Hard Drive, Part 2.”
N
System
files on hard
drive?
Install OS
and reboot.
Y
Y
Y
Virus
on
hard drive?
OS
loading from
hard drive?
Clean virus.
N
Done
N
Y
Run SCANDISK and
check for
bad sectors.
Diagnostics on
disc or diskette?
Replace
hard drive.
N
N
Can bad
sectors
be fixed?
Run diagnostics
and follow
recommendations.
Replace
hard drive.
Y
N
Boot from
hard drive?
Fix bad
sectors.
Replace
hard drive.
Y
Done
2–22
Maintenance and Service Guide
Troubleshooting
Flowchart 2.13—No OS Loading, Diskette Drive
Y
OS not loading
from
diskette drive.
Reseat
diskette drive.
OS
loading?
Done
N
Y
N
Bootable
diskette
in drive?
Nonsystem
disk message?
N
Y
N
Check diskette
for system files.
Try different
diskette.
Go to
Boot
from another
device?
“Flowchart
2.17—Nonfunctioning Device.”
Y
Y
N
Diskette
drive enabled
in the Setup
utility?
Nonsystem
disk error?
Enable drive
and cold boot
computer.
N
Y
Replace the following
components
individually, retesting
after each
replacement:
■ Diskette drive
■ System board
Y
Y
N
Install bootable
diskette and
reboot computer.
Is diskette
drive boot
order
correct?
Change boot
priority using
the Setup Utility.
OS
loading?
Reset the computer.
Refer to
Section 1.2,
“Resetting the
Computer,” for
Done
N
instructions.
Go to
“Flowchart
2.17—Nonfunctioning
Device.”
Maintenance and Service Guide
2–23
Troubleshooting
Flowchart 2.14—No OS Loading, Optical Drive
Y
No OS
loading from
CD-ROM or
DVD-ROM drive.
N
Install bootable
disc and
reboot
computer.
Bootable
disc in
drive?
Disc
in drive?
Y
N
Install
bootable disc.
Try another
bootable disc.
Y
Boots from
CD or DVD?
Done
N
Y
Boots from
CD or DVD?
Reseat
drive.
Done
N
N
Booting
from another
device?
Y
Y
Booting
order
correct?
N
Go to
“Flowchart
2.17—Nonfunctioning
Device.”
Reset the computer.
Refer to
Go to
Section 1.2,
“Resetting the
Computer,” for
“Flowchart
2.17—Nonfunctioning
Device.”
instructions.
Correct boot
order using
the Setup Utility.
2–24
Maintenance and Service Guide
Troubleshooting
Flowchart 2.15—No Audio, Part 1
Y
Turn up audio
internally or
externally.
No audio.
Audio?
Done
N
N
Y
Computer in
docking device
(if applicable)?
Go to
Internal
audio?
Undock
N
“Flowchart
2.16—No Audio,
Part 2.”
Y
Go to
Replace the
docking device.
“Flowchart
2.16—No Audio,
Part 2.”
Y
Go to
“Flowchart
2.17—Nonfunctioning
Device.”
Audio?
Done
N
Maintenance and Service Guide
2–25
Troubleshooting
Flowchart 2.16—No Audio, Part 2
Continued from
“Flowchart
2.15—No Audio,
Part 1.”
N
Audio
driver in OS
configured?
Reload
audio drivers.
Y
N
Correct
drivers for
application?
Load drivers and
set configuration
in OS.
Y
Connect to
external
speaker.
N
Audio?
Y
Replace audio
board and
speaker
connections
in computer
(if applicable).
Y
Audio?
Done
N
Replace the following components
individually, retesting after each
replacement:
■ Internal speakers
■ Audio board (if applicable)
2–26
Maintenance and Service Guide
Troubleshooting
Flowchart 2.17—Nonfunctioning Device
Nonfunctioning
device.
Reseat
device.
Unplug the nonfunctioning device from the computer
and inspect cables and plugs for bent or broken pins
or other damage.
Y
Clear
CMOS.
Fix or
replace
broken item.
Any physical
device detected?
N
Go to
Reattach device.
Close computer,
plug in power,
and reboot.
“Flowchart
2.9—No
Operating System
(OS) Loading.”
Replace hard drive.
N
Device
boots
properly?
N
Replace NIC.
If integrated NIC,
replace system
board.
Y
Device
boots
properly?
Y
Done
Maintenance and Service Guide
Replace diskette
drive.
Done
2–27
Troubleshooting
Flowchart 2.18—Nonfunctioning Keyboard
Keyboard
not operating
properly.
Connect computer
to good external
keyboard.
N
External
device
works?
Replace
system
board.
Y
Reseat internal
keyboard
connector
(if applicable).
N
Keyboard
operating
properly?
Replace internal
keyboard or
cable.
Y
Y
Keyboard
operating
properly?
Done
Done
N
Replace
system
board.
2–28
Maintenance and Service Guide
Troubleshooting
Flowchart 2.19—Nonfunctioning Pointing
Device
Pointing device
not operating
properly.
Connect computer
to good external
pointing device.
N
Replace
system
board.
External
device
works?
Y
Reseat internal
pointing device
connector
(if applicable).
N
Replace internal
pointing device
or cable.
Pointing device
operating
properly?
Y
Y
Pointing device
operating
properly?
Done
Done
N
Replace
system
board.
Maintenance and Service Guide
2–29
Troubleshooting
Flowchart 2.20—No Network/Modem
Connection
No network
or modem
connection.
N
Replace jack
or have jack
activated.
Network
or modem jack
active?
Y
Y
Connect
to nondigital
line.
Digital
line?
N
Y
N
NIC/modem
configured
in OS?
Network
or modem
connection
working?
Reload
drivers and
reconfigure.
Done
N
Y
Disconnect all
power from
the computer
and open.
Replace
NIC/modem
(if applicable).
Reseat NIC/modem
(if applicable).
Network
or modem
connection
working?
Y
Done
N
Replace
system
board.
2–30
Maintenance and Service Guide
3
Illustrated Parts Catalog
This chapter provides an illustrated parts breakdown and a
reference for spare part numbers and option part numbers.
3.1 Serial Number Location
When ordering parts or requesting information, provide the
computer serial number and model number located on the bottom
of the computer.
Maintenance and Service Guide
3–1
Illustrated Parts Catalog
3.2 Computer Major Components
Computer Major Components
3–2
Maintenance and Service Guide
Illustrated Parts Catalog
Table 3-1
Spare Parts: Computer Major Components
Spare Part
Number
Item
Description
1
Display assemblies (include wireless antenna transceivers
and cables)
For use with full-featured computer models with camera (includes
camera, camera cable, and microphones)
15.4-inch, WXGA, TFT with BrightView
15.4-inch, WXGA, TFT Antiglare
432298-001
431380-001
For use with full-featured computer models without camera
(includes microphones)
15.4-inch, WXGA, TFT with BrightView
15.4-inch, WXGA, TFT Antiglare
432299-001
432301-001
For use with defeatured computer models (does not include camera,
camera cable, or microphones)
15.4-inch, WXGA, TFT with BrightView
15.4-inch, WXGA, TFT Antiglare
432296-001
432297-001
to Section 3.3, “Display Assembly Components,” for
✎ Refer
display assembly internal component spare part number
information.
2
3
Switch covers (include LED board and LED board cable)
For use with full-featured computer models
For use with defeatured computer models
431423-001
431422-001
Power button board (includes power button
board cable)
431437-001
Maintenance and Service Guide
3–3
Illustrated Parts Catalog
Computer Major Components
3–4
Maintenance and Service Guide
Illustrated Parts Catalog
Table 3-1
Spare Parts: Computer Major Components (Continued)
Item
Description
4
Keyboards
Belgium
Denmark
France
French Canada
Germany
Greece
International
Israel
Italy
Norway
Portugal
5
Spare Part
Number
431414-A41
431414-081
431414-051
431414-121
431414-041
431414-151
431414-021
431414-BB1
431414-061
431414-091
431414-131
Russia
Saudi Arabia
Spain
Sweden/Finland
Switzerland
Turkey
The United
Kingdom
The United
States
431414-251
431414-171
431414-071
431414-B71
431414-111
431414-141
431414-031
431414-001
Top covers (include TouchPad and TouchPad cable)
For use with full-featured computer models
For use with defeatured computer models
431416-001
431418-001
6
Speaker assembly
431447-001
7
Top cover support trims
For use with full-featured computer models
For use with defeatured computer models
8
431421-001
431420-001
Fan/heat sink assembly (includes thermal pads)
For use with full-featured computer models
For use with defeatured computer models
Maintenance and Service Guide
431449-001
431448-001
3–5
Illustrated Parts Catalog
Computer Major Components
3–6
Maintenance and Service Guide
Illustrated Parts Catalog
Table 3-1
Spare Parts: Computer Major Components (Continued)
Item
Description
Spare Part
Number
Plastics Kit
431428-001
9a
9b
9c
Includes:
ExpressCard slot bezel
Hard drive cover (includes 2 captive screws, secured by C-clips)
Memory module compartment cover (includes 2 captive screws,
secured by C-clips)
10
ExpressCard assembly
11
Processors (include thermal pad)
12
431439-001
AMD Turion ML-56 1.80-GHz
AMD Turion ML-52 1.60-GHz
AMD Turion ML-50 1.60-GHz
431373-001
431372-001
431371-001
Mobile AMD Sempron 3400+ (1.80-GHz)
Mobile AMD Sempron 3200+ (1.60-GHz)
431375-001
431374-001
System boards
For use with full-featured computer models
with camera
For use with full-featured computer models
without camera
For use with defeatured computer models
433280-001
13
Bluetooth module (includes Bluetooth
module cable)
412766-001
14
USB/power connector boards (include USB/power connector
board cable)
For use with 90W AC adapters
For use with 65W AC adapters
Maintenance and Service Guide
431362-001
431363-001
431446-001
431445-001
3–7
Illustrated Parts Catalog
Computer Major Components
3–8
Maintenance and Service Guide
Illustrated Parts Catalog
Table 3-1
Spare Parts: Computer Major Components (Continued)
Item
Description
15
Audio boards
Spare Part
Number
For use with full-featured computer models (includes
infrared lens)
For use with defeatured computer models (does not
include infrared lens)
16
17
431442-001
Base enclosures (include wireless switch)
For use with full-featured computer models
For use with defeatured computer models
431426-001
432921-001
Rubber Feet Kit (includes computer feet,
not illustrated)
431430-001
Batteries
12-cell, 8.8-AHr
6-cell, 4.0-AHr
18
431441-001
432307-001
432306-001
Hard drives (all 5400-rpm, include frame and connector)
120-GB
100-GB
431407-001
431406-001
Maintenance and Service Guide
80-GB
60-GB
431405-001
431404-001
3–9
Illustrated Parts Catalog
Computer Major Components
3–10
Maintenance and Service Guide
Illustrated Parts Catalog
Table 3-1
Spare Parts: Computer Major Components (Continued)
Spare Part
Number
Item
Description
19
Mini Card modules
■ 802.11a/b/g WLAN Mini Card module for use in the
countries listed below. These countries are
categorized as most of the world (MOW).
407160-001
Antigua &
Barbuda
Argentina
Aruba
Australia
Austria
Azerbaijan
Bahamas
Bahrain
Barbados
Belgium
Bermuda
Brunei
Bulgaria
Canada
The Cayman
Islands
The Czech
Republic
Chile
Columbia
Russia
Saudi Arabia
Serbia and
Montenegro
Singapore
Slovakia
Slovenia
South Africa
Spain
Sri Lanka
Sweden
Switzerland
Taiwan
Turkey
The United
Kingdom
The United
States
Uzbekistan
Vietnam
Croatia
Cyprus
Denmark
The
Dominican
Republic
Egypt
El Salvador
Estonia
Finland
France
Georgia
Germany
Greece
Guam
Guatemala
Hong Kong
Hungary
Iceland
India
Indonesia
Maintenance and Service Guide
Ireland
Italy
Latvia
Lebanon
Liechtenstein
Lithuania
Luxembourg
Malaysia
Malta
Mexico
Monaco
The Netherlands
New Zealand
Norway
Oman
Panama
Paraguay
The Philippines
Poland
Portugal
Romania
3–11
Illustrated Parts Catalog
Computer Major Components
3–12
Maintenance and Service Guide
Illustrated Parts Catalog
Table 3-1
Spare Parts: Computer Major Components (Continued)
Spare Part
Number
Item
Description
19
Mini Card modules (Continued)
■ 802.11b/g WLAN Mini Card module for use in the
MOW countries listed below:
407159-001
Antigua &
Barbuda
Argentina
Aruba
Australia
Austria
Azerbaijan
Bahamas
Bahrain
Barbados
Belgium
Bermuda
Brunei
Bulgaria
Canada
The Cayman
Islands
The Czech
Republic
Chile
Columbia
Russia
Saudi Arabia
Serbia and
Montenegro
Singapore
Slovakia
Slovenia
South Africa
Spain
Sri Lanka
Sweden
Switzerland
Taiwan
Turkey
The United
Kingdom
The United
States
Uzbekistan
Vietnam
Croatia
Cyprus
Denmark
The
Dominican
Republic
Egypt
El Salvador
Estonia
Finland
France
Georgia
Germany
Greece
Guam
Guatemala
Hong Kong
Hungary
Iceland
India
Indonesia
Maintenance and Service Guide
Ireland
Italy
Latvia
Lebanon
Liechtenstein
Lithuania
Luxembourg
Malaysia
Malta
Mexico
Monaco
The Netherlands
New Zealand
Norway
Oman
Panama
Paraguay
The Philippines
Poland
Portugal
Romania
3–13
Illustrated Parts Catalog
Computer Major Components
3–14
Maintenance and Service Guide
Illustrated Parts Catalog
Table 3-1
Spare Parts: Computer Major Components (Continued)
Spare Part
Number
Item
Description
19
Mini Card modules (Continued)
■ 802.11a/b/g WLAN Mini Card module for use in the
countries listed below. These countries are
categorized as the rest of the world (ROW).
407160-002
China
Ecuador
Haiti
Uruguay
Venezuela
Honduras
Pakistan
Peru
Qatar
South Korea
■ 802.11b/g WLAN Mini Card module for use in the
ROW countries listed below:
407160-002
China
Ecuador
Haiti
Uruguay
Venezuela
Honduras
Pakistan
Peru
Qatar
South Korea
20
RTC battery (includes 2-sided tape)
21
Memory modules, PC-5300, 667-MHz, 1-DIMM
1024-MB
512-MB
256-MB
22
431436-001
431403-001
431402-001
431401-001
Optical drives (include bezel)
DVD±RW/R and CD-RW Double-Layer Combo Drive
with LightScribe
DVD±RW/R and CD-RW Double-Layer Combo Drive
DVD/CD-RW Combo Drive
Maintenance and Service Guide
431410-001
431409-001
431408-001
3–15
Illustrated Parts Catalog
3.3 Display Assembly Components
Display Assembly Components
Table 3-2
Display Assembly Components
Spare Part Number Information
Item
Description
1
Display bezels
2
3–16
Spare Part
Number
For use with full-featured computer models with
camera (includes camera and microphone openings)
For use with full-featured computer models without
camera (includes microphone openings)
For use with defeatured computer models
431388-001
Display Hinge Kit (includes left and right
display hinges)
431395-001
433281-001
433282-001
Maintenance and Service Guide
Illustrated Parts Catalog
Table 3-2
Display Assembly Components
Spare Part Number Information (Continued)
Item
Description
Spare Part
Number
3
Display inverter
431391-001
4
Camera module
431392-001
5
Display panels
15.4-inch, WXGA, SVA display panel with BrightView
15.4-inch, WXGA, SVA display panel AntiGlare
431386-001
431387-001
6
Wireless antenna transceivers and cables
431398-001
7
Microphone
431393-001
8
Display Cable Kit (includes camera cable)
431394-001
9
Display enclosures
For use with full-featured computer models
For use with defeatured computer models
431391-001
432919-001
Display hinge covers (not illustrated)
For use with full-featured computer models
For use with defeatured computer models
431396-001
433289-001
Display Screw Kit (includes screws and rubber
screw covers, not illustrated)
431399-001
Maintenance and Service Guide
3–17
Illustrated Parts Catalog
3.4 Mass Storage Devices
Mass Storage Devices
Table 3-3
Mass Storage Devices
Spare Part Number Information
Spare Part
Number
Item
Description
1
Hard drives (all 5400-rpm, include frame and connector)
120-GB
100-GB
80-GB
60-GB
2
3–18
431407-001
431406-001
431405-001
431404-001
Optical drives
DVD±RW/R and CD-RW Double-Layer Combo Drive
with LightScribe
DVD±RW/R and CD-RW Double-Layer Combo Drive
DVD/CD-RW Combo Drive
431410-001
USB digital drive (not illustrated)
364727-001
431409-001
431408-001
Maintenance and Service Guide
Illustrated Parts Catalog
3.5 Plastics Kit
Plastics Kit Components
Table 3-4
Plastics Kit
Spare Part Number Information
Item
1
2
3
Description
Spare Part
Number
Plastics Kit
431428-001
Includes:
ExpressCard slot bezel
Hard drive cover (includes 2 captive screws, secured by C-clips)
Memory module compartment cover (includes 2 captive screws,
secured by C-clips)
Maintenance and Service Guide
3–19
Illustrated Parts Catalog
3.6 Miscellaneous
Table 3-5
Spare Parts: Miscellaneous
Description
Spare Part
Number
AC adapters
HP 90W PFC AC Adapter
HP 90W non-PFC AC Adapter
HP 65W AC Adapter
432309-001
432310-001
402018-001
Analog TV tuner
407941-001
Composite S-Video and audio input cable
407939-001
Headset
371693-001
HP Backpack
405527-001
HP Remote Control
407313-001
Logo Kit
431434-001
RF cable
408485-001
RF input adapter cable
407940-001
TV tuner remote control
408479-001
USB infrared receiver
408483-001
USB travel mouse
309674-001
3–20
Maintenance and Service Guide
Illustrated Parts Catalog
Table 3-5
Spare Parts: Miscellaneous (Continued)
Spare Part
Number
Description
Power cords
For use in:
Australia and New Zealand
394279-011
Belgium, Europe, Finland, France, Germany, Greece,
the Netherlands, Norway, Portugal, Spain, and Sweden
394279-021
Canada, French Canada, Latin America, Thailand, and the
United States
394279-001
Denmark
394279-081
Israel
394279-BB1
Italy
394279-061
Switzerland
394279-111
The United Kingdom and Hong Kong
394279-031
Screw Kit (includes the following screws; refer to
Appendix A, “Screw Listing,” for more information on screw
specifications and usage)
431432-001
■
■
■
■
■
Phillips PM3.0×3.0 screw
Phillips PM2.5×10.0 screw
Phillips PM2.5×7.0 screw
Phillips PM2.5×5.0 screw
Phillips PM2.5×4.0 screw
Maintenance and Service Guide
■ Phillips PM2.0×6.0 Screw
■ Phillips PM2.0×5.0 captive screw
■ Phillips PM2.0×4.0 screw
■ Phillips PM2.0×3.0 screw
3–21
Illustrated Parts Catalog
3.7 Sequential Part Number Listing
Table 3-6
Spare Parts: Sequential Part Number Listing
Spare Part
Number
Description
309674-001
USB travel mouse
364727-001
USB digital drive (not illustrated)
371693-001
Headset
394279-001
Power cord for use in Canada, French Canada, Latin America,
Thailand, and the United States
394279-011
Power cord for use in Australia
394279-021
Power cord for use in Belgium, Europe, Finland, France,
Germany, Greece, the Netherlands, Norway, Portugal, Spain,
and Sweden
394279-031
Power cord for use in the United Kingdom and Hong Kong
394279-061
Power cord for use in Italy
394279-081
Power cord for use in Denmark
394279-111
Power cord for use in Switzerland
394279-BB1
Power cord for use in Israel
402018-001
HP 65W PFC AC Adapter
405527-001
HP Backpack
3–22
Maintenance and Service Guide
Illustrated Parts Catalog
Table 3-6
Spare Parts: Sequential Part Number Listing (Continued)
Spare Part
Number
407159-001
Description
802.11b/g WLAN Mini Card module for use in the MOW
countries listed below:
Antigua &
Barbuda
Argentina
Aruba
Australia
Austria
Azerbaijan
Bahamas
Bahrain
Barbados
Belgium
Bermuda
Brunei
Bulgaria
Canada
The Cayman
Islands
The Czech
Republic
Chile
Columbia
407159-002
Croatia
Cyprus
Denmark
The Dominican
Republic
Egypt
El Salvador
Estonia
Finland
France
Georgia
Germany
Greece
Guam
Guatemala
Hong Kong
Hungary
Iceland
India
Indonesia
Ireland
Italy
Latvia
Lebanon
Liechtenstein
Lithuania
Luxembourg
Malaysia
Malta
Mexico
Monaco
The Netherlands
New Zealand
Norway
Oman
Panama
Paraguay
The Philippines
Poland
Portugal
Romania
802.11b/g WLAN Mini Card module for use in the ROW
countries listed below:
China
Ecuador
Haiti
Maintenance and Service Guide
Honduras
Pakistan
Peru
Qatar
South Korea
3–23
Illustrated Parts Catalog
Table 3-6
Spare Parts: Sequential Part Number Listing (Continued)
Spare Part
Number
407160-001
Description
802.11a/b/g WLAN Mini Card module for use in the MOW
countries listed below:
Antigua &
Barbuda
Argentina
Aruba
Australia
Austria
Azerbaijan
Bahamas
Bahrain
Barbados
Belgium
Bermuda
Brunei
Bulgaria
Canada
The Cayman
Islands
The Czech
Republic
Chile
Columbia
407160-002
Croatia
Cyprus
Denmark
The Dominican
Republic
Egypt
El Salvador
Estonia
Finland
France
Georgia
Germany
Greece
Guam
Guatemala
Hong Kong
Hungary
Iceland
India
Indonesia
802.11a/b/g WLAN Mini Card module for use in the ROW
countries listed below:
China
Ecuador
Haiti
Honduras
Pakistan
Peru
407313-001
HP Remote Control
407939-001
Composite S-Video and audio input cable
3–24
Ireland
Italy
Latvia
Lebanon
Liechtenstein
Lithuania
Luxembourg
Malaysia
Malta
Mexico
Monaco
The Netherlands
New Zealand
Norway
Oman
Panama
Paraguay
The Philippines
Poland
Portugal
Romania
Qatar
South Korea
Maintenance and Service Guide
Illustrated Parts Catalog
Table 3-6
Spare Parts: Sequential Part Number Listing (Continued)
Spare Part
Number
Description
407940-001
RF input adapter cable
407941-001
Analog TV tuner
408479-001
TV tuner remote control
408483-001
USB infrared receiver
408485-001
RF cable
412766-001
Bluetooth module (includes Bluetooth module cable)
431362-001
System board for use with full-featured computer models
without camera
431363-001
System board for use with defeatured computer models
431371-001
AMD Turion ML-50 1.60-GHz processor (includes
thermal pad)
431372-001
AMD Turion ML-52 1.60-GHz processor (includes
thermal pad)
431373-001
AMD Turion ML-56 1.80-GHz processor (includes
thermal pad)
431374-001
Mobile AMD Sempron 3200+ 1.60-GHz processor (includes
thermal pad)
431375-001
Mobile AMD Sempron 3400+ 1.80-GHz processor (includes
thermal pad)
431380-001
15.4-inch, WXGA, TFT Antiglare display assembly for use
with full-featured computer models with camera (includes
camera, camera cable, microphones, and wireless antenna
transceivers and cables)
431386-001
15.4-inch, WXGA, SVA display panel with BrightView
431387-001
15.4-inch, WXGA, SVA AntiGlare display panel
Maintenance and Service Guide
3–25
Illustrated Parts Catalog
Table 3-6
Spare Parts: Sequential Part Number Listing (Continued)
Spare Part
Number
Description
431388-001
Display bezel for use with full-featured computer models
431389-001
Display enclosure for use with full-featured computer models
431391-001
Display inverter
431392-001
Camera module
431393-001
Microphone (includes microphone receivers and cables)
431394-001
Display Cable Kit
431395-001
Display Hinge Kit
431396-001
Display hinge covers for use with full-featured
computer models (includes left and right display hinge covers)
431398-001
Wireless antenna transceivers and cables
431399-001
Display Screw Kit (includes screws and rubber screw covers)
431401-001
256-MB memory module (PC-5300, 667-MHz, 1-DIMM)
431402-001
512-MB memory module (PC-5300, 667-MHz, 1-DIMM)
431403-001
1024-MB memory module (PC-5300, 667-MHz, 1-DIMM)
431404-001
60-GB hard drive (5400-rpm, includes frame and connector)
431405-001
80-GB hard drive (5400-rpm, includes frame and connector)
431406-001
100-GB hard drive (5400-rpm, includes frame and connector)
431407-001
120-GB hard drive (5400-rpm, includes frame and connector)
431408-001
DVD/CD-RW Combo Drive
431409-001
DVD±RW/R and CD-RW Double-Layer Combo Drive
3–26
Maintenance and Service Guide
Illustrated Parts Catalog
Table 3-6
Spare Parts: Sequential Part Number Listing (Continued)
Spare Part
Number
Description
431410-001
DVD±RW/R and CD-RW Double-Layer Combo Drive with
LightScribe
431414-001
Keyboard for use in the United States
431414-031
Keyboard for use in the United Kingdom
431414-041
Keyboard for use in Germany
431414-051
Keyboard for use in France
431414-061
Keyboard for use in Italy
431414-071
Keyboard for use in Spain
431414-081
Keyboard for use in Denmark
431414-091
Keyboard for use in Norway
431414-111
Keyboard for use in Switzerland
431414-121
Keyboard for use in French Canada
431414-131
Keyboard for use in Portugal
431414-141
Keyboard for use in Turkey
431414-151
Keyboard for use in Greece
431414-171
Keyboard for use in Saudi Arabia
431414-251
Keyboard for use in Russia
431414-A41
Keyboard for use in Belgium
431414-B31
Keyboard for international use
431414-B71
Keyboard for use in Sweden and Finland
431414-BB1
Keyboard for use in Israel
431416-001
Top cover for use with full-featured computer models
(includes TouchPad and TouchPad cable)
Maintenance and Service Guide
3–27
Illustrated Parts Catalog
Table 3-6
Spare Parts: Sequential Part Number Listing (Continued)
Spare Part
Number
Description
431418-001
Top cover for use with defeatured computer models (includes
TouchPad and TouchPad cable)
431420-001
Top cover support trim for use with defeatured
computer models
431421-001
Top cover support trim for use with full-featured
computer models
431422-001
Switch cover for use with defeatured computer models
(includes LED board and LED board cable)
431423-001
Switch cover for use with full-featured computer models
(includes LED board and LED board cable)
431426-001
Base enclosure for use with full-featured computer models
(includes wireless switch)
431428-001
Plastics Kit
431430-001
Rubber Feet Kit (includes computer feet, not illustrated)
431432-001
Screw Kit
431434-001
Logo Kit
431436-001
RTC battery (includes 2-sided tape)
431437-001
Power button board (includes power button board cable)
431439-001
ExpressCard assembly
431441-001
Audio board for use with full-featured computer models
(includes infrared lens)
431442-001
Audio board for use with defeatured computer models (does
not include infrared lens)
431445-001
USB/power connector board for use with 65W AC adapters
(includes USB/power connector board cable)
3–28
Maintenance and Service Guide
Illustrated Parts Catalog
Table 3-6
Spare Parts: Sequential Part Number Listing (Continued)
Spare Part
Number
Description
431446-001
USB/power connector board for use with 90W AC adapters
(includes USB/power connector board cable)
431447-001
Speaker assembly
431448-001
Fan/heat sink assembly for use with defeatured computer
models (includes thermal pads)
431449-001
Fan/heat sink assembly for use with full-featured computer
models (includes thermal pads)
432296-001
15.4-inch, WXGA, TFT display assembly with BrightView for
use with defeatured computer models (includes wireless
antenna transceivers and cables; does not include camera,
camera cable, or microphones)
432297-001
15.4-inch, WXGA, TFT Antiglare display assembly for use
with defeatured computer models (includes wireless antenna
transceivers and cables; does not include camera, camera
cable, or microphones)
432298-001
15.4-inch, WXGA, TFT display assembly with BrightView for
use with full-featured computer models with camera (includes
camera, camera cable, microphones, and wireless antenna
transceivers and cables)
432299-001
15.4-inch, WXGA, TFT display assembly with BrightView for
use with full-featured computer models without camera
(includes microphones and wireless antenna transceivers and
cables; does not include camera or camera cable)
432301-001
15.4-inch, WXGA, TFT Antiglare display assembly for use
with full-featured computer models without camera (includes
microphones and wireless antenna transceivers and cables;
does not include camera or camera cable)
432306-001
6-cell, 4.0-AHr battery
432307-001
12-cell, 8.8-AHr battery
Maintenance and Service Guide
3–29
Illustrated Parts Catalog
Table 3-6
Spare Parts: Sequential Part Number Listing (Continued)
Spare Part
Number
Description
432309-001
HP 90W PFC AC Adapter
432310-001
HP 90W non-PFC AC Adapter
432919-001
Display enclosure for use with defeatured computer models
432921-001
Base enclosure for use with defeatured computer models
(includes wireless switch)
433280-001
System board for use with full-featured computer models
with camera
433281-001
Display bezel for use with full-featured computer models
without camera (includes microphone openings; does not
include camera opening)
433282-001
Display bezel for use with defeatured computer models (does
not include camera opening or microphone openings)
433289-001
Display Hinge covers for use with defeatured computer
models (includes left and right display hinge covers)
3–30
Maintenance and Service Guide
4
Removal and Replacement
Preliminaries
This chapter provides essential information for proper and
safe removal and replacement service.
4.1 Tools Required
You will need the following tools to complete the removal and
replacement procedures:
■ Magnetic screwdriver
■ Phillips P0 and P1 screwdrivers
■ Flat-bladed screwdriver
Maintenance and Service Guide
4–1
Removal and Replacement Preliminaries
4.2 Service Considerations
The following sections include some of the considerations
that you should keep in mind during disassembly and assembly
procedures.
you remove each subassembly from the computer, place
✎ As
the subassembly (and all accompanying screws) away from
the work area to prevent damage.
Plastic Parts
Using excessive force during disassembly and reassembly can
damage plastic parts. Use care when handling the plastic parts.
Apply pressure only at the points designated in the maintenance
instructions.
Cables and Connectors
Ä
CAUTION: When servicing the computer, ensure that cables are
placed in their proper locations during the reassembly process.
Improper cable placement can damage the computer.
Cables must be handled with extreme care to avoid damage.
Apply only the tension required to unseat or seat the cables
during removal and insertion. Handle cables by the connector
whenever possible. In all cases, avoid bending, twisting, or
tearing cables. Ensure that cables are routed in such a way that
they cannot be caught or snagged by parts being removed or
replaced. Handle flex cables with extreme care; these cables
tear easily.
4–2
Maintenance and Service Guide
Removal and Replacement Preliminaries
4.3 Preventing Damage to
Removable Drives
Removable drives are fragile components that must be handled
with care. To prevent damage to the computer, damage to a
removable drive, or loss of information, observe the following
precautions:
■ Before removing or inserting a hard drive, shut down the
computer. If you are unsure whether the computer is off or
in hibernation, turn the computer on, and then shut it down
through the operating system.
■ Before removing a diskette drive or optical drive, ensure that
a diskette or disc is not in the drive and ensure that the optical
drive tray is closed.
■ Before handling a drive, ensure that you are discharged of
static electricity. While handling a drive, avoid touching the
connector.
■ Handle drives on surfaces covered with at least one inch of
shock-proof foam.
■ Avoid dropping drives from any height onto any surface.
■ After removing a hard drive, CD-ROM drive, or a diskette
drive, place it in a static-proof bag.
■ Avoid exposing a hard drive to products that have magnetic
fields, such as monitors or speakers.
■ Avoid exposing a drive to temperature extremes or liquids.
■ If a drive must be mailed, place the drive in a bubble pack
mailer or other suitable form of protective packaging and label
the package, “FRAGILE: Handle With Care.”
Maintenance and Service Guide
4–3
Removal and Replacement Preliminaries
4.4 Preventing Electrostatic Damage
Many electronic components are sensitive to electrostatic
discharge (ESD). Circuitry design and structure determine the
degree of sensitivity. Networks built into many integrated circuits
provide some protection, but in many cases, the discharge
contains enough power to alter device parameters or melt
silicon junctions.
A sudden discharge of static electricity from a finger or other
conductor can destroy static-sensitive devices or microcircuitry.
Often the spark is neither felt nor heard, but damage occurs.
An electronic device exposed to electrostatic discharge might not
be affected at all and can work perfectly throughout a normal
cycle. Or the device might function normally for a while, then
degrade in the internal layers, reducing its life expectancy.
4–4
Maintenance and Service Guide
Removal and Replacement Preliminaries
4.5 Packaging and Transporting
Precautions
Use the following grounding precautions when packaging and
transporting equipment:
■ To avoid hand contact, transport products in static-safe
containers, such as tubes, bags, or boxes.
■ Protect all electrostatic-sensitive parts and assemblies with
conductive or approved containers or packaging.
■ Keep electrostatic-sensitive parts in their containers until
the parts arrive at static-free workstations.
■ Place items on a grounded surface before removing items
from their containers.
■ Always be properly grounded when touching a sensitive
component or assembly.
■ Store reusable electrostatic-sensitive parts from assemblies
in protective packaging or nonconductive foam.
■ Use transporters and conveyors made of antistatic belts and
roller bushings. Ensure that mechanized equipment used for
moving materials is wired to ground and that proper materials
are selected to avoid static charging. When grounding is not
possible, use an ionizer to dissipate electric charges.
Maintenance and Service Guide
4–5
Removal and Replacement Preliminaries
4.6 Workstation Precautions
Use the following grounding precautions at workstations:
■ Cover the workstation with approved static-shielding material
(refer to Table 4-2, “Static-Shielding Materials”).
■ Use a wrist strap connected to a properly grounded work
surface and use properly grounded tools and equipment.
■ Use conductive field service tools, such as cutters,
screwdrivers, and vacuums.
■ When using fixtures that must directly contact dissipative
surfaces, only use fixtures made of static-safe materials.
■ Keep the work area free of nonconductive materials, such
as ordinary plastic assembly aids and Styrofoam.
■ Handle electrostatic-sensitive components, parts, and
assemblies by the case or PCM laminate. Handle these
items only at static-free workstations.
■ Avoid contact with pins, leads, or circuitry.
■ Turn off power and input signals before inserting or removing
connectors or test equipment.
4–6
Maintenance and Service Guide
Removal and Replacement Preliminaries
4.7 Grounding Equipment and
Methods
Grounding equipment must include either a wrist strap or a
foot strap at a grounded workstation.
■ When seated, wear a wrist strap connected to a grounded
system. Wrist straps are flexible straps with a minimum of
one megohm ±10% resistance in the ground cords. To provide
proper ground, wear a strap snugly against the skin at all times.
On grounded mats with banana-plug connectors, use alligator
clips to connect a wrist strap.
■ When standing, use foot straps and a grounded floor mat.
Foot straps (heel, toe, or boot straps) can be used at standing
workstations and are compatible with most types of shoes
or boots. On conductive floors or dissipative floor mats, use
foot straps on both feet with a minimum of one megohm
resistance between the operator and ground. To be effective,
the conductive strips must be worn in contact with the skin.
Other grounding equipment recommended for use in preventing
electrostatic damage includes:
■ Antistatic tape
■ Antistatic smocks, aprons, and sleeve protectors
■ Conductive bins and other assembly or soldering aids
■ Nonconductive foam
■ Conductive tabletop workstations with ground cords of
one megohm resistance
■ Static-dissipative tables or floor mats with hard ties to
the ground
■ Field service kits
■ Static awareness labels
■ Material-handling packages
■ Nonconductive plastic bags, tubes, or boxes
■ Metal tote boxes
■ Electrostatic voltage levels and protective materials
Maintenance and Service Guide
4–7
Removal and Replacement Preliminaries
Table 4-1 shows how humidity affects the electrostatic voltage
levels generated by different activities.
Table 4-1
Typical Electrostatic Voltage Levels
Relative Humidity
Event
10%
40%
55%
Walking across carpet
35,000 V
15,000 V
7,500 V
Walking across vinyl floor
12,000 V
5,000 V
3,000 V
Motions of bench worker
6,000 V
800 V
400 V
Removing DIPS from plastic tube
2,000 V
700 V
400 V
Removing DIPS from vinyl tray
11,500 V
4,000 V
2,000 V
Removing DIPS from Styrofoam
14,500 V
5,000 V
3,500 V
Removing bubble pack from PCB
26,500 V
20,000 V
7,000 V
Packing PCBs in foam-lined box
21,000 V
11,000 V
5,000 V
✎ A product can be degraded by as little as 700 V.
Table 4-2 lists the shielding protection provided by antistatic
bags and floor mats.
Table 4-2
Static-Shielding Materials
Material
Use
Voltage Protection Level
Antistatic plastic
Bags
1,500 V
Carbon-loaded plastic
Floor mats
7,500 V
Metallized laminate
Floor mats
5,000 V
4–8
Maintenance and Service Guide
5
Removal and Replacement
Procedures
This chapter provides removal and replacement procedures.
There are as many as 81 screws, in 8 different sizes, that must be
removed, replaced, or loosened when servicing the computer.
Make special note of each screw size and location during removal
and replacement.
Refer to Appendix A, “Screw Listing,” for detailed information
on screw sizes, locations, and usage.
5.1 Serial Number
Report the computer serial number to HP when requesting
information or ordering spare parts. The serial number is
located on the bottom of the computer.
Serial Number Location
Maintenance and Service Guide
5–1
Removal and Replacement Procedures
5.2 Disassembly Sequence Chart
Use the chart below to determine the section number to be
referenced when removing computer components.
Disassembly Sequence Chart
Section
Description
5.3
Preparing the Computer For
Disassembly
# of Screws Removed
Battery
0
5.4
Hard Drive
2 loosened to remove the hard
drive cover
6 removed to disassemble the
hard drive
5.5
Computer Feet
0
5.6
Memory Module
2 loosened to remove the
memory module compartment
cover
5.7
RTC Battery
0
5.8
Mini Card Module
2
Ä
To prevent an unresponsive system and the display of a
warning message, install only a Mini Card device
authorized for use in your computer by the governmental
agency that regulates wireless devices in your country. If
you install a device and then receive a warning message,
remove the device to restore computer functionality. Then
contact Customer Care.
5.9
Optical Drive
1 to remove the optical drive
2 to remove the optical drive
bracket
5.10
Switch Cover
3
5.11
Keyboard
4
5–2
Maintenance and Service Guide
Removal and Replacement Procedures
Disassembly Sequence Chart (Continued)
Section
Description
# of Screws Removed
5.12
Speaker Assembly
2
5.13
Power Button Board
2
5.14
Display Assembly
Display bezel
Camera module
Display inverter
Display panel
Display hinges
Wireless antenna transceivers
Microphones
Camera cable
4
6
0
0
4
4
2
0
0
5.15
Top Cover
14 to remove the top cover
4 to remove the top cover
support trim
5.16
Audio Board
2
5.17
Bluetooth Module
2
5.18
ExpressCard Assembly
4
5.19
USB/Power Connector Board
2
5.20
System Board
2
5.21
Fan/Heat Sink Assembly
4
5.22
Processor
1 loosened
Maintenance and Service Guide
5–3
Removal and Replacement Procedures
5.3 Preparing the Computer For
Disassembly
Before you begin any removal or installation procedures:
1. Shut down the computer. If you are unsure whether the
computer is off or in hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power cord.
Battery Spare Part Number Information
12-cell, 8.8-AHr
6-cell, 4.0-AHr
432307-001
432306-001
4. Remove the battery by following these steps:
a. Turn the computer upside down with the front panel
toward you.
5–4
Maintenance and Service Guide
Removal and Replacement Procedures
b. Slide and hold the battery release latch 1 to the left.
(The front edge of the battery disengages from
the computer.)
c. Lift the front edge of the battery 2 and swing it back.
d. Remove the battery.
Removing the Battery
Reverse the above procedure to install the battery.
Maintenance and Service Guide
5–5
Removal and Replacement Procedures
5.4 Hard Drive
Hard Drive Spare Part Number Information
5400-rpm, 120-GB
5400-rpm, 100-GB
5400-rpm, 80-GB
5400-rpm, 60-GB
431407-001
431406-001
431405-001
431404-001
1. Prepare the computer for disassembly (refer to Section 5.3).
2. Loosen the two Phillips PM2.0×5.0 screws 1 that secure the
hard drive cover to the computer.
3. Lift the right side of the cover 2 and swing it to the left.
4. Remove the hard drive cover.
hard drive cover is included in the Plastics Kit, spare part
✎ The
number 431428-001.
Removing the Hard Drive Cover
5–6
Maintenance and Service Guide
Removal and Replacement Procedures
5. Use the mylar tab 1 to lift the hard drive 2 until it
disconnects from the computer.
6. Remove the hard drive from the hard drive bay.
Removing the Hard Drive
Maintenance and Service Guide
5–7
Removal and Replacement Procedures
7. Remove the six Phillips PM3.0×3.0 screws 1 that secure the
hard drive frame to the hard drive.
8. Lift the frame 2 straight up to remove if from the hard drive.
Removing the Hard Drive Frame
Reverse the above procedure to install and reassemble the
hard drive.
5–8
Maintenance and Service Guide
Removal and Replacement Procedures
5.5 Computer Feet
The computer feet are adhesive-backed rubber pads. The feet are
included in the Rubber Feet Kit, spare part number 431430-001.
The feet attach to the base enclosure in the locations illustrated
below.
Computer Feet Locations
Maintenance and Service Guide
5–9
Removal and Replacement Procedures
5.6 Memory Module
Memory Module Spare Part Number Information
PC2-5300, 667-MHz
1024-MB
512-MB
256-MB
431403-001
431402-001
431401-001
1. Prepare the computer for disassembly (refer to Section 5.3).
2. Loosen the two Phillips PM2.0×5.0 screws 1 that secure the
memory module compartment cover to the computer.
3. Lift the left side of the memory module compartment
cover 2, and then swing it to the right.
4. Remove the memory module compartment cover.
memory module compartment cover is included in the
✎ The
Plastics Kit, spare part number 431428-001.
Removing the Memory Module Compartment Cover
5–10
Maintenance and Service Guide
Removal and Replacement Procedures
5. Spread the retaining tabs 1 on each side of the memory
module socket to release the memory module. (The edge of
the module opposite the socket rises away from the
computer.)
6. Slide the module 2 away from the socket at an angle.
modules are designed with a notch 3 to prevent
✎ Memory
incorrect installation into the memory module socket.
Removing a Memory Module
Reverse the above procedure to install a memory module.
Maintenance and Service Guide
5–11
Removal and Replacement Procedures
5.7 RTC Battery
RTC Battery Spare Part Number Information
RTC battery (includes 2-sided tape)
431436-001
1. Prepare the computer for disassembly (refer to Section 5.3).
2. Remove the memory module compartment cover
(Section 5.6).
3. Disconnect the RTC battery cable 1 from the system board.
4. Remove the RTC battery 2.
RTC battery is secured to the computer by 2-sided tape. All
✎ The
replacement RTC battery spare part kits include 2-sided tape.
Removing the RTC Battery
Reverse the above procedure to install the RTC battery.
5–12
Maintenance and Service Guide
Removal and Replacement Procedures
5.8 Mini Card Module
Mini Card Module Spare Part Number Information
802.11a/b/g WLAN Mini Card module for use in MOW the
countries listed below:
407160-001
Antigua &
Barbuda
Argentina
Aruba
Australia
Austria
Azerbaijan
Bahamas
Bahrain
Barbados
Belgium
Bermuda
Brunei
Bulgaria
Canada
The Cayman
Islands
The Czech
Republic
Chile
Columbia
Romania
Russia
Saudi Arabia
Serbia and
Montenegro
Singapore
Slovakia
Slovenia
South Africa
Spain
Sri Lanka
Sweden
Switzerland
Taiwan
Turkey
The United
Kingdom
The United States
Uzbekistan
Vietnam
Croatia
Cyprus
Denmark
The Dominican
Republic
Egypt
El Salvador
Estonia
Finland
France
Georgia
Germany
Greece
Guam
Guatemala
Hong Kong
Hungary
Iceland
India
Indonesia
Ireland
Italy
Latvia
Lebanon
Liechtenstein
Lithuania
Luxembourg
Malaysia
Malta
Mexico
Monaco
The Netherlands
New Zealand
Norway
Oman
Panama
Paraguay
The Philippines
Poland
Portugal
802.11a/b/g WLAN Mini Card module for use in ROW the
countries listed below:
407160-002
China
Ecuador
Haiti
Uruguay
Venezuela
Honduras
Pakistan
Peru
Maintenance and Service Guide
Qatar
South Korea
5–13
Removal and Replacement Procedures
Mini Card Module Spare Part Number Information (Continued)
802.11b/g WLAN Mini Card module for use in the MOW
countries listed below:
407159-001
Antigua &
Barbuda
Argentina
Aruba
Australia
Austria
Azerbaijan
Bahamas
Bahrain
Barbados
Belgium
Bermuda
Brunei
Bulgaria
Canada
The Cayman
Islands
The Czech
Republic
Chile
Columbia
Romania
Russia
Saudi Arabia
Serbia and
Montenegro
Singapore
Slovakia
Slovenia
South Africa
Spain
Sri Lanka
Sweden
Switzerland
Taiwan
Turkey
The United
Kingdom
The United States
Uzbekistan
Vietnam
Croatia
Cyprus
Denmark
The Dominican
Republic
Egypt
El Salvador
Estonia
Finland
France
Georgia
Germany
Greece
Guam
Guatemala
Hong Kong
Hungary
Iceland
India
Indonesia
Ireland
Italy
Latvia
Lebanon
Liechtenstein
Lithuania
Luxembourg
Malaysia
Malta
Mexico
Monaco
The Netherlands
New Zealand
Norway
Oman
Panama
Paraguay
The Philippines
Poland
Portugal
802.11b/g WLAN Mini Card module for use in the ROW
countries listed below:
407160-002
China
Ecuador
Haiti
Uruguay
Venezuela
Honduras
Pakistan
Peru
Qatar
South Korea
1. Prepare the computer for disassembly (Section 5.3).
2. Remove the memory module compartment cover
(Section 5.6).
5–14
Maintenance and Service Guide
Removal and Replacement Procedures
3. Make note of which wireless antenna cable is attached to
which antenna clip on the Mini Card module before
disconnecting the cables, Then disconnect the cables 1 from
the module.
4. Remove the two Phillips PM2.5×5.0 screws 2 that secure the
Mini Card module to the computer. (The edge of the module
opposite the socket rises away from the computer).
5. Remove the module 3 by pulling it away from the socket at
an angle.
Card modules are designed with a notch 4 to prevent
✎ Mini
incorrect installation into the Mini Card module socket.
Removing a Mini Card Module
Reverse the above procedure to install a Mini Card module.
Maintenance and Service Guide
5–15
Removal and Replacement Procedures
5.9 Optical Drive
Optical Drive Spare Part Number Information
DVD±RW/R and CD-RW Double-Layer Combo Drive with
LightScribe
DVD±RW/R and CD-RW Double-Layer Combo Drive
DVD/CD-RW Combo Drive
431410-001
431409-001
431408-001
1. Prepare the computer for disassembly (Section 5.3).
2. Remove the Phillips PM2.5×7.0 screw 1 that secures the
optical drive to the computer.
3. Insert a thin tool, such as a paper clip 2, into the media tray
release hole. (The optical drive media tray releases from the
optical drive.)
4. Use the media tray frame to slide the optical drive 3 out of
the computer.
5. Remove the optical drive.
Removing the Optical Drive
5–16
Maintenance and Service Guide
Removal and Replacement Procedures
6. Position the optical drive with the optical drive bracket
toward you.
7. Remove the two Phillips PM2.0×3.0 screws 1 that secure the
optical drive bracket to the optical drive.
8. Remove the optical drive 2.
Removing the Optical Drive Bracket
Reverse the above procedure to reassemble and install the
optical drive.
Maintenance and Service Guide
5–17
Removal and Replacement Procedures
5.10 Switch Cover
Switch Cover Spare Part Number Information
For use with full-featured computer models
For use with defeatured computer models
431423-001
431422-001
1. Prepare the computer for disassembly (Section 5.3).
2. Close the computer.
3. Turn the computer upside down with the front panel
toward you.
4. Remove the three Phillips PM2.5×5.0 screws that secure the
switch cover to the computer.
Removing the Switch Cover Screws
5. Turn the computer display-side up with the front toward you.
6. Open the computer as far as possible.
5–18
Maintenance and Service Guide
Removal and Replacement Procedures
7. Lift the rear edge of the switch cover and swing it forward
until it rests on the keyboard.
Releasing the Switch Cover
8. Release the zero insertion force (ZIF) connector 1 to which
the LED board cable is connected and disconnect the cable 2
from the LED board.
9. Remove the switch cover.
Disconnecting the LED Board Cable
Reverse the above procedure to install the switch cover.
Maintenance and Service Guide
5–19
Removal and Replacement Procedures
5.11 Keyboard
Keyboard Spare Part Number Information
Belgium
Denmark
France
French Canada
Germany
Greece
International
Israel
Italy
Norway
431414-A41
431414-081
431414-051
431414-121
431414-041
431414-151
431414-021
431414-BB1
431414-061
431414-091
Portugal
Russia
Saudi Arabia
Spain
Sweden/Finland
Switzerland
Turkey
The United Kingdom
The United States
431414-131
431414-251
431414-171
431414-071
431414-B71
431414-111
431414-141
431414-031
431414-001
1. Prepare the computer for disassembly (Section 5.3).
2. Remove the switch cover (Section 5.10).
3. Remove the four Phillips PM2.5×7.0 screws that secure the
keyboard to the computer.
Removing the Keyboard Screws
5–20
Maintenance and Service Guide
Removal and Replacement Procedures
4. Turn the computer display-side up with the front panel
toward you.
5. Open the computer as far as possible.
6. Lift the rear edge of the keyboard 1 until it rests at an angle.
7. Slide the keyboard 2 back to disengage the tabs on the front
edge of the keyboard from the top cover.
8. Swing the keyboard 3 forward until it rests on the palm rest.
Releasing the Keyboard
Maintenance and Service Guide
5–21
Removal and Replacement Procedures
9. Release the ZIF connector 1 to which the keyboard cable is
connected and disconnect the keyboard cable 2 from the
system board.
Disconnecting the Keyboard Cable
10. Remove the keyboard.
Reverse the above procedure to install the keyboard.
5–22
Maintenance and Service Guide
Removal and Replacement Procedures
5.12 Speaker Assembly
Speaker Assembly Spare Part Number Information
Speaker assembly
431447-001
1. Prepare the computer for disassembly (Section 5.3).
2. Remove the switch cover (Section 5.10).
3. Remove the keyboard (Section 5.11).
4. Disconnect the speaker assembly cable 1 from the power
button board.
5. Remove the two Phillips PM2.5×4.0 screws 2 that secure the
speaker assembly to the computer.
6. Remove the speaker assembly 3.
Removing the Speaker Assembly
Reverse the above procedure to install the speaker assembly.
Maintenance and Service Guide
5–23
Removal and Replacement Procedures
5.13 Power Button Board
Power Button Board Spare Part Number Information
Power button board (includes power button board cable)
431437-001
1. Prepare the computer for disassembly (Section 5.3).
2. Remove the switch cover (Section 5.10).
3. Remove the keyboard (Section 5.11).
4. Disconnect the microphone cable 1 and the speaker
assembly cable 2 from the power button board.
5. Release the ZIF connector 3 to which the power button board
is connected and disconnect the cable 4.
6. Remove the power button board cable from the clip 5 in the
top cover.
Disconnecting the Power Button Board Cables
5–24
Maintenance and Service Guide
Removal and Replacement Procedures
7. Remove the two Phillips PM2.0×3.0 screws 1 that secure the
power button board to the computer.
8. Remove the power button board 2.
Removing the Power Button Board
Reverse the above procedure to install the power button board.
Maintenance and Service Guide
5–25
Removal and Replacement Procedures
5.14 Display Assembly
Display Assembly Spare Part Number Information
For use with full-featured computer models with camera (includes camera,
camera cable, and microphones)
15.4-inch, WXGA, TFT with BrightView
15.4-inch, WXGA, TFT Antiglare
432298-001
431380-001
For use with full-featured computer models without camera
(includes microphones)
15.4-inch, WXGA, TFT with BrightView
15.4-inch, WXGA, TFT Antiglare
432299-001
432301-001
For use with defeatured computer models (does not include camera,
camera cable, or microphones)
432296-001
432297-001
15.4-inch, WXGA, TFT with BrightView
15.4-inch, WXGA, TFT Antiglare
1. Prepare the computer for disassembly (Section 5.3) and
remove the following components:
❏ Memory module compartment cover (Section 5.8)
❏ Switch cover (Section 5.10)
❏ Keyboard (Section 5.11)
❏ Speaker assembly (Section 5.12)
2. Close the computer.
3. Turn the computer upside down with the rear panel toward you.
5–26
Maintenance and Service Guide
Removal and Replacement Procedures
4. Make note of which wireless antenna cable is attached to
which antenna clip on the Mini Card module before
disconnecting the cables. Then disconnect the cables 1 from
the module.
5. Remove the two Phillips PM2.5×7.0 screws 2 that secure the
display assembly to the computer.
Removing the Display Assembly Screws
6. Turn the comuter display-side up with the front toward you.
7. Open the computer to an upright position.
Maintenance and Service Guide
5–27
Removal and Replacement Procedures
8. Disconnect the following cables:
1 Display cable
2 Microphone cable
3 Camera cable
9. Remove the wireless antenna cables 4 from the routing
channels in the top cover.
Disconnecting the Display Cables
5–28
Maintenance and Service Guide
Removal and Replacement Procedures
Ä
CAUTION: Support the display assembly when removing the following
screws. Failure to support the display assembly can result in damage to
the display assembly and other computer components.
10. Remove the two Phillips PM2.5×7.0 screws 1 that secure the
display assembly to the computer.
11. Remove the display assembly 2.
Removing the Display Assembly
Maintenance and Service Guide
5–29
Removal and Replacement Procedures
12. Remove the following:
1 Four rubber screw covers on the display bezel top edge
2 Two rubber screw covers on the display bezel bottom edge
3 Four Phillips PM2.5×5.0 screws on the display bezel
top edge
4 Two Phillips PM2.5×7.0 screws on the display bezel
bottom edge
display rubber screw covers are included in the Display
✎ The
Screw Kit, spare part number 431399-001.
Removing the Display Bezel Screws
5–30
Maintenance and Service Guide
Removal and Replacement Procedures
Display Assembly Subcomponents
Spare Part Number Information
Display bezels
For use with full-featured computer models with camera
(includes camera and microphone openings)
For use with full-featured computer models without camera
(includes microphone openings)
For use with defeatured computer models
431388-001
433281-001
433282-001
13. Flex the inside edges of the left and right sides 1 and the top
and bottom sides 2 of the display bezel until the bezel
disengages from the display enclosure.
14. Remove the display bezel 3.
Removing the Display Bezel
Maintenance and Service Guide
5–31
Removal and Replacement Procedures
Display Assembly Subcomponents
Spare Part Number Information
Camera module
431392-001
15. Remove the camera module 1 from the display enclosure.
16. Disconnect the camera cable 2 from the camera module.
Removing the Camera Module
5–32
Maintenance and Service Guide
Removal and Replacement Procedures
Display Assembly Subcomponents
Spare Part Number Information
Display inverter
431391-001
17. Remove the inverter 1 from the display enclosure.
18. Disconnect the display cable 2 and the backlight cable 3
from the display inverter.
Removing the Display Inverter
Maintenance and Service Guide
5–33
Removal and Replacement Procedures
Display Assembly Subcomponents
Spare Part Number Information
Display panels
15.4-inch, WXGA, SVA display panel with BrightView
15.4-inch, WXGA, SVA display panel AntiGlare
431386-001
431387-001
19. Remove the four Phillips PM2.5×5.0 screws 1 that secure the
display panel to the display enclosure.
20. Remove the display panel 2.
Removing the Display Panel
5–34
Maintenance and Service Guide
Removal and Replacement Procedures
Display Assembly Subcomponents
Spare Part Number Information
Display Hinge Kit
431395-001
Display hinge covers (not illustrated)
For use with full-featured computer models
For use with defeatured computer models
431396-001
433289-001
21. Slide the left and right display hinge covers 1 off of the
display hinges.
22. Remove the two Phillips PM2.0×3.0 screws 2 that secure
each hinge to the display enclosure.
23. Remove the display hinges 3.
Removing the Display Hinges
Maintenance and Service Guide
5–35
Removal and Replacement Procedures
Display Assembly Subcomponents
Spare Part Number Information
Wireless antenna transceivers and cables
431398-001
24. If it is necessary to replace the wireless antenna transceivers
and cables, remove the Phillips PM2.0×4.0 screw 1 that
secures each transceiver to the display enclosure.
25. Remove the wireless antenna cables from the clips 2 built
into the display enclosure.
26. Detach the wireless antenna transceivers 3 from the
display enclosure.
27. Remove the wireless antenna cables 4.
Removing the Wireless Antenna Transceivers and Cables
5–36
Maintenance and Service Guide
Removal and Replacement Procedures
Display Assembly Subcomponents
Spare Part Number Information
Microphone
431393-001
28. If it is necessary to replace the microphones and cables,
release the retention tabs 1 built into the display enclosure
that secure the microphone cables to the display enclosure.
29. Remove the microphone receivers 2 from the clips in the
display enclosure.
30. Remove the microphone cables 3 from the display enclosure.
Removing the Microphones
Maintenance and Service Guide
5–37
Removal and Replacement Procedures
Display Assembly Subcomponents
Spare Part Number Information
Display Cable Kit (includes camera cable)
431394-001
31. If it is necessary to replace the camera cable, release the
retention tabs 1 built into the display enclosure that secure
the camera cable to the display enclosure.
32. Remove the camera cable 2 from the display enclosure.
Removing the Camera Cable
Reverse the above procedure to reassemble and install the
display assembly
5–38
Maintenance and Service Guide
Removal and Replacement Procedures
5.15 Top Cover
Top Cover Spare Part Number Information
Top covers (include TouchPad and TouchPad cable)
For use with full-featured computer models
For use with defeatured computer models
431416-001
431418-001
Top cover support trims
For use with full-featured computer models
For use with defeatured computer models
431421-001
431420-001
1. Prepare the computer for disassembly (Section 5.3) and
remove the following components:
❏ Hard drive (Section 5.4)
❏ Optical drive (Section 5.9)
❏ Switch cover (Section 5.10)
❏ Keyboard (Section 5.11)
❏ Speaker assembly (Section 5.12)
❏ Display assembly (Section 5.14)
Maintenance and Service Guide
5–39
Removal and Replacement Procedures
2. Turn the computer upside down with the front toward you.
3. Remove the nine Phillips PM2.5×7.0 screws that secure the
top cover to the computer.
Removing the Top Cover Screws, Part 1
4. Remove the three Phillips PM2.5×2.0 screws 1 and the
three Phillips PM2.5×7.0 screws 2 that secure the top cover
support trim to the computer.
Removing the Top Cover Screws, Part 2
5–40
Maintenance and Service Guide
Removal and Replacement Procedures
5. Turn the computer right-side up with the front toward you.
6. Release and disconnect the following ZIF cables from the
system board:
1 Power button board cable
2 LED board cable
3 TouchPad cable
Disconnecting the Top Cover Cables
Maintenance and Service Guide
5–41
Removal and Replacement Procedures
7. Remove the Phillips PM2.5×7.0 screw 1 that secures the top
cover support trim to the computer.
8. Remove the two Phillips PM2.5×7.0 screws 2 that secure the
top cover to the computer.
Removing the Top Cover Screws, Part 3
5–42
Maintenance and Service Guide
Removal and Replacement Procedures
9. Remove the top cover support trim 1.
10. Lift the rear edge of the top cover 2 until it disengages from
the computer.
11. Remove the top cover.
Removing the Top Cover
Reverse the above procedure to install the top cover.
Maintenance and Service Guide
5–43
Removal and Replacement Procedures
5.16 Audio Board
Audio Board Spare Part Number Information
For use with full-featured computer models (includes
infrared lens)
For use with defeatured computer models (does not include
infrared lens)
431441-001
431442-001
1. Prepare the computer for disassembly (Section 5.3) and
remove the following components:
❏ Hard drive (Section 5.4)
❏ Optical drive (Section 5.9)
❏ Switch cover (Section 5.10)
❏ Keyboard (Section 5.11)
❏ Speaker assembly (Section 5.12)
❏ Display assembly (Section 5.14)
❏ Top cover (Section 5.15)
5–44
Maintenance and Service Guide
Removal and Replacement Procedures
2. Remove the two Phillips PM2.5×5.0 screws 1 that secure the
audio board to the computer.
3. Slide the audio board 2 back to disengage the audio
connectors from the base enclosure.
4. Remove the audio board 3.
5. Disconnect the audio board cable 4 from the audio board.
Removing the Audio Board
Reverse the above procedure to install the audio board.
Maintenance and Service Guide
5–45
Removal and Replacement Procedures
5.17 Bluetooth Module
Bluetooth Module Spare Part Number Information
Bluetooth module (includes Bluetooth module cable)
412766-001
1. Prepare the computer for disassembly (Section 5.3) and
remove the following components:
❏ Hard drive (Section 5.4)
❏ Optical drive (Section 5.9)
❏ Switch cover (Section 5.10)
❏ Keyboard (Section 5.11)
❏ Speaker assembly (Section 5.12)
❏ Display assembly (Section 5.14)
❏ Top cover (Section 5.15)
5–46
Maintenance and Service Guide
Removal and Replacement Procedures
2. Disconnect the Bluetooth module cable 1 from the
system board.
3. Remove the two Phillips PM2.0×3.0 screws 2 that secure the
Bluetooth module to the system board.
4. Remove the Bluetooth module 3.
Removing the Bluetooth Module
Reverse the above procedure to install the Bluetooth module.
Maintenance and Service Guide
5–47
Removal and Replacement Procedures
5.18 ExpressCard Assembly
ExpressCard Assembly Spare Part Number Information
ExpressCard assembly
431439-001
1. Prepare the computer for disassembly (Section 5.3) and
remove the following components:
❏ Hard drive (Section 5.4)
❏ Optical drive (Section 5.9)
❏ Switch cover (Section 5.10)
❏ Keyboard (Section 5.11)
❏ Speaker assembly (Section 5.12)
❏ Display assembly (Section 5.14)
❏ Top cover (Section 5.15)
2. Push in on the ExpressCard bezel 1 to release the bezel from
the ExpressCard slot.
3. Remove the ExpressCard bezel 2.
ExpressCard bezel is included in the Plastics Kit, spare
✎ The
part number 431428-001.
Removing the ExpressCard Slot Bezel
5–48
Maintenance and Service Guide
Removal and Replacement Procedures
4. Remove the four Phillips PM2.5×5.0 screws 1 that secure the
ExpressCard assembly to the system board.
5. Slide the ExpressCard assembly 2 to the right to disconnect
it from the system board.
6. Remove the ExpressCard assembly 3.
Removing the ExpressCard Assembly
Reverse the above procedure to install the ExpressCard assembly.
Maintenance and Service Guide
5–49
Removal and Replacement Procedures
5.19 USB/Power Connector Board
USB/Power Connector Board Spare Part Number Information
USB/power connector boards (include USB/power connector board cable)
For use with 90W AC adapters
For use with 65W AC adapters
431446-001
431445-001
1. Prepare the computer for disassembly (Section 5.3) and
remove the following components:
❏ Hard drive (Section 5.4)
❏ Optical drive (Section 5.9)
❏ Switch cover (Section 5.10)
❏ Keyboard (Section 5.11)
❏ Speaker assembly (Section 5.12)
❏ Display assembly (Section 5.14)
❏ Top cover (Section 5.15)
5–50
Maintenance and Service Guide
Removal and Replacement Procedures
2. Remove the two Phillips PM2.5×5.0 screws 1 that secure the
USB/power connector board to the computer.
3. Release the USB/power connector board 2 as far as the
USB/power connector board cable will allow.
4. Disconnect the USB board cable 3 and the power connector
board cable 4 from the USB/power connector board.
Removing the USB/Power Connector Board
5. Remove the USB/power connector board.
Reverse the above procedure to install the USB/power
connector board.
Maintenance and Service Guide
5–51
Removal and Replacement Procedures
5.20 System Board
System Board Spare Part Number Information
For use with full-featured computer models with camera
For use with full-featured computer models without camera
For use with defeatured computer models
433280-001
431362-001
431363-001
replacing the system board, ensure that the following
✎ When
components are removed from the defective system board and
installed on the replacement system board:
■ Memory modules (Section 5.6)
■ RTC battery (Section 5.7)
■ Mini Card module (Section 5.8)
■ Bluetooth module (Section 5.17)
■ ExpressCard assembly (Section 5.18)
■ Fan/heat sink assembly (Section 5.21)
■ Processor (Section 5.22)
5–52
Maintenance and Service Guide
Removal and Replacement Procedures
1. Prepare the computer for disassembly (Section 5.3) and
remove the following components:
❏ Hard drive (Section 5.4)
❏ Optical drive (Section 5.9)
❏ Switch cover (Section 5.10)
❏ Keyboard (Section 5.11)
❏ Speaker assembly (Section 5.12)
❏ Display assembly (Section 5.14)
❏ Top cover (Section 5.15)
❏ Audio board (Section 5.16)
❏ USB/power connector board (Section 5.19)
2. Remove the USB/power connector board cable 1 from the
clips in the base enclosure.
3. Remove the two Phillips PM2.5×5.0 screws 2 that secure the
system board to the base enclosure.
Removing the System Board Screws
Maintenance and Service Guide
5–53
Removal and Replacement Procedures
4. Use the optical drive connector 1 to lift the right side of the
system board 2 until it rests at an angle.
5. Slide the system board 3 to the right until the connectors on the
left side of the system board disengage from the base enclosure.
6. Remove the system board.
Removing the System Board
5–54
Maintenance and Service Guide
Removal and Replacement Procedures
7. If it is necessary to replace the USB/power connector board
cable or the audio board cable, turn the system board upside
down with the front toward you.
8. Disconnect the audio board cable 1 and the USB/power
connector board cable 2 from the system board.
Removing the System Board Cables
Reverse the above procedure to install the system board,
USB/power connector board cable, and audio board cable.
Maintenance and Service Guide
5–55
Removal and Replacement Procedures
5.21 Fan/Heat Sink Assembly
Fan/Heat Sink Assembly Spare Part Number Information
For use with full-featured computer models
For use with defeatured computer models
431449-001
431448-001
replacing the fan/heat sink assembly, be sure the power
✎ When
button board is removed from the defective fan/heat sink
assembly and installed on the replacement fan/heat sink
assembly. Refer to Section 5.13, “Power Button Board,” for
power button board removal information.
1. Prepare the computer for disassembly (Section 5.3) and
remove the following components:
❏ Hard drive (Section 5.4)
❏ Optical drive (Section 5.9)
❏ Switch cover (Section 5.10)
❏ Keyboard (Section 5.11)
❏ Speaker assembly (Section 5.12)
❏ Display assembly (Section 5.14)
❏ Top cover (Section 5.15)
❏ Audio board (Section 5.16)
❏ USB/power connector board (Section 5.19)
❏ System board (Section 5.20)
2. Turn the system board upside down with the expansion port 3
and external monitor port toward you.
5–56
Maintenance and Service Guide
Removal and Replacement Procedures
3. Disconnect the fan cable 1 from the system board.
4. Remove the four Phillips PM2.5×5.0 screws 2 that secure the
fan/heat sink assembly to the system board.
5. Remove the fan/heat sink assembly 3.
Removing the Fan/Heat Sink Assembly
Maintenance and Service Guide
5–57
Removal and Replacement Procedures
thermal pads and thermal paste should be thoroughly
✎ The
cleaned from the surfaces of the fan/heat sink assembly 1, 2,
and 3, the system board components 4 and 6, and the
processor 5 each time the fan/heat sink assembly is removed.
Thermal pads and thermal paste should be installed on all
surfaces before the fan/heat sink assembly is reinstalled.
Thermal pads and thermal paste are included with all fan/heat
sink assembly, system board, and processor spare part kits.
Thermal Pad and Thermal Paste Locations
Reverse the above procedure to install the fan/heat sink assembly.
5–58
Maintenance and Service Guide
Removal and Replacement Procedures
5.22 Processor
Processor Spare Part Number Information
AMD Turion ML-56 1.80-GHz
AMD Turion ML-52 1.60-GHz
AMD Turion ML-50 1.60-GHz
431373-001
431372-001
431371-001
Mobile AMD Sempron 3400+ (1.80-GHz)
Mobile AMD Sempron 3200+ (1.60-GHz)
431375-001
431374-001
1. Prepare the computer for disassembly (Section 5.3) and
remove the following components:
❏ Hard drive (Section 5.4)
❏ Optical drive (Section 5.9)
❏ Switch cover (Section 5.10)
❏ Keyboard (Section 5.11)
❏ Speaker assembly (Section 5.12)
❏ Display assembly (Section 5.14)
❏ Top cover (Section 5.15)
❏ Audio board (Section 5.16)
❏ USB/power connector board (Section 5.19)
❏ System board (Section 5.20)
Maintenance and Service Guide
5–59
Removal and Replacement Procedures
2. Turn the processor locking screw 1 one-half turn
counterclockwise until you hear a click.
3. Lift the processor 2 straight up and remove it.
The gold triangle 3 on the processor should be aligned with
✎ the
triangle icon 4 embossed on the processor socket when
you install the processor.
Removing the Processor
Reverse the above procedure to install the processor.
5–60
Maintenance and Service Guide
6
Specifications
This chapter provides physical and performance specifications.
Table 6-1
Computer
Dimensions
Length
Width
Height (varies front to rear)
Weight (varies by configuration)
35.7 cm
25.7 cm
4.1 cm
14.05 in
10.12 in
1.57 in
2.7 kg
5.8 lb
Stand-alone power requirements
Operating voltage
Operating current
18.5 V dc —19.0 V dc
3.5 A or 4.74 A
Temperature
Operating*
Nonoperating
5°C to 35°C
-20°C to 60°C
41°F to 95°F
-4°F to 140°F
Relative humidity (noncondensing)
Operating
Nonoperating
10% to 90%
5% to 95%, 38.7°C (101.6°F) maximum
wet bulb temperature
Maximum altitude (unpressurized)
Operating (14.7 to 10.1 psia)
Nonoperating (14.7 to 4.4 psia)
Maintenance and Service Guide
-15 m to 3,048 m
-15 m to 12,192 m
-50 ft to 10,000 ft
-50 ft to 40,000 ft
6–1
Specifications
Table 6-1
Computer (Continued)
Shock
Operating
Nonoperating
125 g, 2 ms, half-sine
200 g, 2 ms, half-sine
Random Vibration
Operating
Nonoperating
0.75 g zero-to-peak, 10 Hz to 500 Hz,
0.25 oct/min sweep rate
1.50 g zero-to-peak, 10 Hz to 500 Hz,
0.5 oct/min sweep rate
*Applicable product safety standards specify thermal limits for plastic surfaces.
The computer operates well within this range of temperatures.
6–2
Maintenance and Service Guide
Specifications
Table 6-2
15.4-inch, WXGA, SVA Display
Dimensions
Height
Width
Diagonal
20.7 cm
33.1 cm
39.1 cm
Number of colors
Up to 16.8 million
Contrast ratio
200:1
Brightness
160 nits typical
8.15 in
13.03 in
15.39 in
Pixel resolution
Pitch
Format
Configuration
0.259 × 0.259 mm
1280 × 800
RGB vertical stripe
Backlight
Edge lit
Character display
80 × 25
Total power consumption
4W
Viewing angle
+/-65° horizontal, +/-50° vertical typical
Maintenance and Service Guide
6–3
Specifications
Table 6-3
Hard Drives
120-GB*
100-GB*
Dimensions
Height
Width
Weight
9.5 mm
70 mm
102 g
9.5 mm
70 mm
102 g
Interface type
ATA-5
ATA-5
100 MB/sec
ATA security
100 MB/sec
ATA security
Single track
Average
Maximum
3 ms
13 ms
24 ms
3 ms
13 ms
24 ms
Logical blocks†
234,433,260
195,364,233
Transfer rate
Synchronous (maximum)
Security
Seek times (typical read, including setting)
Disk rotational speed
Operating temperature
5400 rpm
5°C to 55°C (41°F to 131°F)
restrictions and exclusions apply. Consult Customer Care
✎ forCertain
details.
*1 GB = 1 billion bytes when referring to hard drive storage capacity. Accessible
capacity is less. Actual drive specifications may differ slightly.
6–4
Maintenance and Service Guide
Specifications
Table 6-3
Hard Drives (Continued)
80-GB*
60-GB*
Dimensions
Height
Width
Weight
9.5 mm
70 mm
99 g
9.5 mm
70 mm
99 g
Interface type
ATA-5
ATA-5
100 MB/sec
ATA security
100 MB/sec
ATA security
Single track
Average
Maximum
3 ms
13 ms
24 ms
3 ms
13 ms
24 ms
Logical blocks†
156,301,488
117,210,240
Transfer rate
Synchronous (maximum)
Security
Seek times (typical read, including setting)
Disk rotational speed
Operating temperature
5400 rpm
5°C to 55°C (41°F to 131°F)
restrictions and exclusions apply. Consult Customer Care
✎ forCertain
details.
*1 GB = 1 billion bytes when referring to hard drive storage capacity. Accessible
capacity is less. Actual drive specifications may differ slightly.
Maintenance and Service Guide
6–5
Specifications
Table 6-4
Primary 6-cell, Li-Ion Battery
Dimensions
Height
Width
Depth
Weight
2.00 cm
9.40 cm
13.40 cm
0.34 kg
0.79 in
3.70 in
5.28 in
0.75 lb
Energy
Voltage
Amp-hour capacity
Watt-hour capacity
11.1 V
4.4 Ah
48 Wh
Temperature
Operating
Nonoperating
6–6
5°C to 45°C
0°C to 60°C
41°F to 113°F
32°F to 140°F
Maintenance and Service Guide
Specifications
Table 6-5
DVD/CD-RW Combo Drive
Applicable disc
Read:
Write:
DVD-R, DVD-RW,
CD-R and CD-RW
DVD-ROM (DVD-5,
DVD-9, DVD-10,
DVD-18),
CD-ROM (Mode 1 and 2)
CD Digital Audio
CD-XA ready (Mode 2,
Form 1 and 2)
CD-I ready (Mode 2,
Form 1 and 2)
CD-R, CD-RW
Photo CD (single and
multisession)
CD-Bridge
Center hole diameter
1.5 cm (0.59 in)
Disc diameter
Standard disc
Mini disc
12 cm (4.72 in)
8 cm (3.15 in)
Maintenance and Service Guide
6–7
Specifications
Table 6-5
DVD/CD-RW Combo Drive (Continued)
Disc thickness
1.2 mm (0.047 in)
Track pitch
0.74 µm
Access time
CD media
DVD media
< 110 ms
< 210 ms
< 130 ms
< 225 ms
Random
Full stroke
Audio output level
Line-out, 0.7 V rms
Cache buffer
2 MB
Data transfer rate
CD-R (24X)
CD-RW (10X)
CD-ROM (24X)
DVD (8X)
Multiword DMA mode 2
3600 KB/s (150 KB/s at 1X CD rate)
1500 KB/s (150 KB/s at 1X CD rate)
3600 KB/s (150 KB/s at 1X CD rate)
10,800 KB/s (1352 KB/s at 1X DVD rate)
16.6 MB/s
Startup time
< 15 seconds
Stop time
< 6 seconds
6–8
Maintenance and Service Guide
Specifications
Table 6-6
DVD±RW/R and
CD-RW Double-Layer Combo Drive
Applicable disc
Read:
Write:
DVD-R, DVD-RW,
CD-R and CD-RW
DVD-ROM (DVD-5,
DVD-R and DVD-RW
DVD-9, DVD-10,
DVD-18),
CD-ROM (Mode 1 and 2)
CD Digital Audio
CD-XA ready (Mode 2,
Form 1 and 2)
CD-I ready (Mode 2,
Form 1 and 2)
CD-R, CD-RW
Photo CD (single and
multisession)
CD-Bridge
Center hole diameter
1.5 cm (0.59 in)
Disc diameter
Standard disc
Mini disc
12 cm (4.72 in)
8 cm (3.15 in)
Maintenance and Service Guide
6–9
Specifications
Table 6-6
DVD±RW/R and
CD-RW Double-Layer Combo Drive (Continued)
Disc thickness
1.2 mm (0.047 in)
Track pitch
0.74 µm
Access time
CD media
DVD media
< 175 ms
< 285 ms
< 230 ms
< 335 ms
Random
Full stroke
Audio output level
Audio-out, 0.7 Vrms
Cache buffer
2 MB
Data transfer rate
CD-R (16X)
CD-RW (8X)
CD-ROM (24X)
DVD (8X)
DVD-R (4X)
DVD-RW (2X)
Multiword DMA mode 2
2,400 KB/s (150 KB/s at 1X CD rate)
1,200 KB/s (150 KB/s at 1X CD rate)
3,600 KB/s (150 KB/s at 1X CD rate)
10,800 KB/s (1,352 KB/s at 1X DVD rate)
5,400 KB/s (1,352 KB/s at 1X DVD rate)
2,700 KB/s (1,352 KB/s at 1X DVD rate)
16.6 MB/s
Startup time
< 15 seconds
Stop time
< 6 seconds
6–10
Maintenance and Service Guide
Specifications
Table 6-7
System DMA
Hardware DMA
System Function
DMA0
Not applicable
DMA1
Not applicable
DMA2
Not applicable
DMA3
Not applicable
DMA4
Direct memory access controller
DMA5
Available for ExpressCard
DMA6
Not assigned
DMA7
Not assigned
Maintenance and Service Guide
6–11
Specifications
Table 6-8
System Interrupts
Hardware IRQ
System Function
IRQ0
System timer
IRQ1
Quick Launch buttons
IRQ2
Cascaded
IRQ3
USB2 Enhanced Host Controller—24CD
IRQ4
COM1
IRQ5*
Conexant AC—Link Audio
SMBus Controller—24C3
Data Fax Modem with SmartCP
IRQ6
Diskette drive
IRQ7*
Parallel port
IRQ8
System CMOS/real-time clock
IRQ9*
Microsoft ACPI-compliant system
IRQ10*
USB UHCI controller—24C2
GM/GME Graphic Controller
Realtek RTL8139 Family PCI fast Ethernet Controller
IRQ11
USB EHCI controller—24CD
USB UHCI controller—24C4
USB UHCI controller—24C7
Pro/Wireless 2200BG
TI OHCI 1394 host controller
TI PCI1410 CardBus controller
*Default configuration
✎ ExpressCard may assert IRQ3, IRQ4, IRQ5, IRQ7, or IRQ20.
6–12
Maintenance and Service Guide
Specifications
Table 6-8
System Interrupts (Continued)
Hardware IRQ
System Function
IRQ12
Synaptics PS/2 port pointing device
IRQ13
Numeric data processor
IRQ14
Primary IDE channel
IRQ15
Secondary IDE channel
IRQ17
Conexant AC -Link Audio
IRQ17
Soft V90 Data Fax Modem with SmartCP
IRQ17
ATi Mobility Radeon Xpress 200 Series
IRQ19
Standard Enhanced PCI to USB Host Controller
IRQ19
Standard OpenHCD USB Host Controller
IRQ19
Standard OpenHCD USB Host Controller
IRQ20
TI 6411 PCIxx21/x515 Cardbus Controller
IRQ20
TI OHCI Compliant IEEE 1394 Host Controller
IRQ21
TI Integrated PCIxx21 FlashMedia Controller
IRQ21
Broadcom 802.11b/g WLAN
IRQ21
Microsoft ACPI-compliant system
IRQ22
Realtek RTL8100CL Family PCI fast Ethernet
Controller
IRQ23
SDA Standard Compliant SD Host Controller
*Default configuration
✎ ExpressCard may assert IRQ3, IRQ4, IRQ5, IRQ7, or IRQ20.
Maintenance and Service Guide
6–13
Specifications
Table 6-9
System I/O Addresses
I/O Address (hex)
System Function (shipping configuration)
0x00000000-0x00000CF7
PCI bus
0x00000000-0x00000CF7
Direct memory access controller
0x00000020-0x00000021
Programmable interrupt controller
0x0000002E-0x0000002F
System board resources
0x00000040-0x00000043
System timer
0x00000060-0x00000060
Quick Launch Buttons
0x00000061-0x00000061
System speaker
0x00000062-0x00000062
Microsoft ACPI-Compliant Embedded
Controller
0x00000064-0x00000064
Quick Launch Buttons
0x00000066-0x00000066
Microsoft ACPI-Compliant Embedded
Controller
0x00000070-0x00000071
System CMOS/real time clock
0x00000072-0x00000073
System board resources
0x00000080-0x0000008F
Direct memory access controller
0x00000092-0x00000092
System board resources
0x000000A0-0x000000A1
Programmable interrupt controller
0x000000B0-0x000000B1
System board resources
0x000000C0-0x000000DF
Direct memory access controller
0x000000F0-0x000000FE
Numeric data processor
0x00000170-0x00000177
Secondary IDE Channel
6–14
Maintenance and Service Guide
Specifications
Table 6-9
System I/O Addresses (Continued)
I/O Address (hex)
System Function (shipping configuration)
0x000001F0-0x000001F7
Primary IDE Channel
0x00000220-0x0000022F
System board resources
0x00000274-0x00000277
ISAPNP Read Data Port
0x00000279-0x00000279
ISAPNP Read Data Port
0x00000280-0x00000293
System board resources
0x00000376-0x00000376
Secondary IDE Channel
0x000003B0-0x000003BB
PCI standard PCI-to-PCI bridge
0x000003B0-0x000003BB
ATI MOBILITY RADEON Xpress 200 Series
0x000003C0-0x000003DF
PCI standard PCI-to-PCI bridge
0x000003C0-0x000003DF
ATI MOBILITY RADEON Xpress 200 Series
0x000003F6-0x000003F6
Primary IDE Channel
0x0000040B-0x0000040B
System board resources
0x000004D0-0x000004D1
System board resources
0x000004D6-0x000004D6
System board resources
0x00000530-0x00000537
System board resources
0x00000870-0x0000087F
System board resources
0x00000A79-0x00000A79
ISAPNP Read Data Port
0x00000C00-0x00000C01
System board resources
0x00000C14-0x00000C14
System board resources
0x00000C50-0x00000C52
System board resources
0x00000C6C-0x00000C6C
System board resources
Maintenance and Service Guide
6–15
Specifications
Table 6-9
System I/O Addresses (Continued)
I/O Address (hex)
System Function (shipping configuration)
0x00000C6F-0x00000C6F
System board resources
0x00000CD4-0x00000CD5
System board resources
0x00000CD6-0x00000CD7
System board resources
0x00000CD8-0x00000CDF
System board resources
0x00000D00-0x0000FFFF
PCI bus
0x00000F40-0x00000F47
System board resources
0x00001080-0x00001080
System board resources
0x00008000-0x0000805F
System board resources
0x00008100-0x000081FF
System board resources
0x00008400-0x0000840F
ATI SMBus
0x00008410-0x0000841F
Standard Dual Channel PCI IDE Controller
0x00009000-0x00009FFF
PCI standard PCI-to-PCI bridge
0x00009000-0x00009FFF
ATI MOBILITY RADEON Xpress 200 Series
0x0000A000-0x0000A0FF
Realtek RTL8139/810x Family Fast Ethernet
NIC
0x0000F000-0x0000FFFF
PCI standard PCI-to-PCI bridge
0x0000FD00-0x0000FDFF
Texas Instruments PCIxx21/x515 Cardbus
Controller
0x0000FE00-0x0000FEFF
Texas Instruments PCIxx21/x515 Cardbus
Controller
6–16
Maintenance and Service Guide
Specifications
Table 6-10
System Memory Map
Memory Map Address (hex)
System Function (shipping configuration)
0xD4100000-0xD41FFFFF
PCI standard PCI-to-PCI bridge
0xD4100000-0xD41FFFFF
ATI MOBILITY RADEON Xpress 200 Series
0xD8000000-0xDBFFFFFF
PCI standard PCI-to-PCI bridge
0xD8000000-0xDBFFFFFF
ATI MOBILITY RADEON Xpress 200 Series
0xFAC00000-0xFEBFFFFF
PCI standard PCI-to-PCI bridge
0xF6C00000-0xFABFFFFF
PCI standard PCI-to-PCI bridge
0xD4000000-0xD4000FFF
Standard OpenHCD USB Host Controller
0xD4001000-0xD4001FFF
Standard OpenHCD USB Host Controller
0xD4002000-0xD4002FFF
Standard Enhanced PCI to USB Host
Controller
0xD4003000-0xD40033FF
ATI SMBus
0xFFF80000-0xFFFFFFFF
System board
0xE0000000-0xE03FFFFF
System board
0xE0000000-0xE03FFFFF
System board resources
0x0000-0x0FFF
System board
0xD4208000-0xD42087FF
Texas Instruments OHCI Compliant IEEE
1394 Host Controller
0xD4200000-0xD4203FFF
Texas Instruments OHCI Compliant IEEE
1394 Host Controller
0xD4204000-0xD4205FFF
Broadcom 802.11b/g WLAN
0xFFEFF000-0xFFEFFFFF
Texas Instruments PCIxx21/x515 Cardbus
Controller
0xFFEFE000-0xFFEFEFFF
Texas Instruments PCIxx21/x515 Cardbus
Controller
Maintenance and Service Guide
6–17
Specifications
Table 6-10
System Memory Map (Continued)
Memory Map Address (hex)
System Function (shipping configuration)
0xF2C00000-0xF6BFFFFF
Texas Instruments PCIxx21/x515 Cardbus
Controller
0xD4206000-0xD4207FFF
Texas Instruments PCIxx21 Integrated
FlashMedia Controller
0xD4209000-0xD42090FF
SDA Standard Compliant SD Host Controller
0xD4208C00-0xD4208CFF
SDA Standard Compliant SD Host Controller
0xD4208800-0xD42088FF
SDA Standard Compliant SD Host Controller
0xD4209400-0xD42094FF
Realtek RTL8139/810x Family Fast
Ethernet NIC
0xD4003400-0xD40034FF
Conexant AC-Link Audio
0xD4003800-0xD40038FF
SoftV90 Data Fax Modem with SmartCP
0xFEC00000-0xFEC00FFF
System board resources
0xFEE00000-0xFEE00FFF
System board resources
0xA0000-0xBFFFF
PCI bus
0xA0000-0xBFFFF
PCI standard PCI-to-PCI bridge
0xA0000-0xBFFFF
ATI MOBILITY RADEON Xpress 200 Series
0xD6000-0xD7FFF
PCI bus
0xDC000-0xDDFFF
PCI bus
0xDD000-0xDDFFF
Texas Instruments PCIxx21/x515 Cardbus
Controller
0xE0000-0xFFFFF
System board
0x40000000-0xFFFFFFFF
PCI bus
6–18
Maintenance and Service Guide
A
Screw Listing
This appendix provides specification and reference information
for the screws used in the computer. All screws listed in this
appendix are available in the Screw Kit, spare part number
431432-001, and the Display Screw Kit, spare part number
431399-001.
Maintenance and Service Guide
A–1
Screw Listing
Table A-1
Phillips PM2.0×5.0 Captive Screw
mm
Color
Qty.
Length
Thread
Head
Width
Black
4
5.0 mm
2.0 mm
5.0 mm
Where used:
1 Two screws that secure the hard drive cover to the computer (screws are
captured on the cover by C-clips; documented in Section 5.4)
2 Two screws that secure the memory module compartment cover to the
computer (screws are captured on the cover by C-clips; documented in
Section 5.6)
Phillips PM2.0×5.0 Captive Screw Locations
A–2
Maintenance and Service Guide
Screw Listing
Table A-2
Phillips PM3.0×3.0 Screw
mm
Color
Qty.
Length
Thread
Head
Width
Silver
6
3.0 mm
3.0 mm
5.0 mm
Where used:
6 screws that secure the hard drive frame to the hard drive (documented in
Section 5.4)
Phillips PM3.0×3.0 Screw Locations
Maintenance and Service Guide
A–3
Screw Listing
Table A-3
Phillips PM2.5×5.0 Screw
mm
Color
Qty.
Length
Thread
Head
Width
Silver
27
5.0 mm
2.5 mm
5.0 mm
Where used:
2 screws that secure the Mini Card module to the computer (documented in
Section 5.8)
Phillips PM2.5×5.0 Screw Locations
A–4
Maintenance and Service Guide
Screw Listing
Table A-3
Phillips PM2.5×5.0 Screw (Continued)
mm
Color
Qty.
Length
Thread
Head
Width
Silver
27
5.0 mm
2.5 mm
5.0 mm
Where used:
3 screws that secure the top cover to the base enclosure (documented in
Section 5.15)
Phillips PM2.5×5.0 Screw Locations
Maintenance and Service Guide
A–5
Screw Listing
Table A-3
Phillips PM2.5×5.0 Screw (Continued)
mm
Color
Qty.
Length
Thread
Head
Width
Silver
27
5.0 mm
2.5 mm
5.0 mm
Where used:
4 screws that secure the display bezel to the display enclosure (documented in
Section 5.14)
Phillips PM2.5×5.0 Screw Locations
A–6
Maintenance and Service Guide
Screw Listing
Table A-3
Phillips PM2.5×5.0 Screw (Continued)
mm
Color
Qty.
Length
Thread
Head
Width
Silver
27
5.0 mm
2.5 mm
5.0 mm
Where used:
4 screws that secure the display panel to the display enclosure (documented in
Section 5.14)
Phillips PM2.5×5.0 Screw Locations
Maintenance and Service Guide
A–7
Screw Listing
Table A-3
Phillips PM2.5×5.0 Screw (Continued)
mm
Color
Qty.
Length
Thread
Head
Width
Silver
27
5.0 mm
2.5 mm
5.0 mm
Where used:
1 Two screws that secure the audio board to the computer (documented in
Section 5.16)
2 Four screws that secure the ExpressCard assembly to the system board
(documented in Section 5.18)
3 Two screws that secure the USB/power connector board to the computer
(documented in Section 5.19)
4 Two screws that secure the system board to the computer (documented in
Section 5.20)
Phillips PM2.5×5.0 Screw Locations
A–8
Maintenance and Service Guide
Screw Listing
Table A-3
Phillips PM2.5×5.0 Screw (Continued)
mm
Color
Qty.
Length
Thread
Head
Width
Silver
27
5.0 mm
2.5 mm
5.0 mm
Where used:
Four screws that secure the fan/heat sink assembly to the system board
(documented in Section 5.21)
Phillips PM2.5×5.0 Screw Locations
Maintenance and Service Guide
A–9
Screw Listing
Table A-4
Phillips PM2.5×7.0 Screw
mm
Color
Qty.
Length
Thread
Head
Width
Black
26
7.0 mm
2.5 mm
5.0 mm
Where used:
1 One screw that secures the optical drive to the computer (documented in
Section 5.9)
2 Four screws that secure the keyboard to the computer (documented in
Section 5.11)
3 Two screws that secure the display assembly to the computer (documented in
Section 5.14)
Phillips PM2.5×7.0 Screw Locations
A–10
Maintenance and Service Guide
Screw Listing
Table A-4
Phillips PM2.5×7.0 Screw (Continued)
mm
Color
Qty.
Length
Thread
Head
Width
Black
26
7.0 mm
2.5 mm
5.0 mm
Where used:
2 screws that secure the display assembly to the computer (documented in
Section 5.14)
Phillips PM2.5×7.0 Screw Locations
Maintenance and Service Guide
A–11
Screw Listing
Table A-4
Phillips PM2.5×7.0 Screw (Continued)
mm
Color
Qty.
Length
Thread
Head
Width
Black
26
7.0 mm
2.5 mm
5.0 mm
Where used:
2 screws that secure the display bezel to the display assembly (documented in
Section 5.14)
Phillips PM2.5×7.0 Screw Locations
A–12
Maintenance and Service Guide
Screw Listing
Table A-4
Phillips PM2.5×7.0 Screw (Continued)
mm
Color
Qty.
Length
Thread
Head
Width
Black
26
7.0 mm
2.5 mm
5.0 mm
Where used:
9 screws that secure the top cover to the computer (documented in
Section 5.15)
Phillips PM2.5×7.0 Screw Locations
Maintenance and Service Guide
A–13
Screw Listing
Table A-4
Phillips PM2.5×7.0 Screw (Continued)
mm
Color
Qty.
Length
Thread
Head
Width
Black
26
7.0 mm
2.5 mm
5.0 mm
Where used:
3 screws that secure the top cover support trim to the computer (documented in
Section 5.15)
Phillips PM2.5×7.0 Screw Locations
A–14
Maintenance and Service Guide
Screw Listing
Table A-4
Phillips PM2.5×7.0 Screw (Continued)
mm
Color
Qty.
Length
Thread
Head
Width
Black
26
7.0 mm
2.5 mm
5.0 mm
Where used:
1 One screw that secures the top cover support trim to the computer
(documented in Section 5.15)
2 Two screws that secure the top cover to the computer (documented in
Section 5.15)
Phillips PM2.5×7.0 Screw Locations
Maintenance and Service Guide
A–15
Screw Listing
Table A-5
Phillips PM2.0×3.0 Screw
mm
Color
Qty.
Length
Thread
Head
Width
Silver
10
3.0 mm
2.0 mm
4.0 mm
Where used:
2 screws that secure the optical drive bracket to the optical drive (documented in
Section 5.9)
Phillips PM2.0×3.0 Screw Locations
A–16
Maintenance and Service Guide
Screw Listing
Table A-5
Phillips PM2.0×3.0 Screw (Continued)
mm
Color
Qty.
Length
Thread
Head
Width
Silver
10
3.0 mm
2.0 mm
4.0 mm
Where used:
2 screws that secure the power button board to the computer (documented in
Section 5.13)
Phillips PM2.0×3.0 Screw Locations
Maintenance and Service Guide
A–17
Screw Listing
Table A-5
Phillips PM2.0×3.0 Screw (Continued)
mm
Color
Qty.
Length
Thread
Head
Width
Silver
10
3.0 mm
2.0 mm
4.0 mm
Where used:
4 screws that secure the display hinges to the display panel (documented in
Section 5.14)
Phillips PM2.0×3.0 Screw Location
A–18
Maintenance and Service Guide
Screw Listing
Table A-5
Phillips PM2.0×3.0 Screw (Continued)
mm
Color
Qty.
Length
Thread
Head
Width
Silver
10
3.0 mm
2.0 mm
4.0 mm
Where used:
2 screws that secure the Bluetooth module to the system board (documented in
Section 5.17)
Phillips PM2.0×3.0 Screw Locations
Maintenance and Service Guide
A–19
Screw Listing
Table A-6
Phillips PM2.5×4.0 Screw
mm
Color
Qty.
Length
Thread
Head
Width
Black
2
4.0 mm
2.5 mm
5.0 mm
Where used:
2 screws that secure the speaker assembly to the computer (documented in
Section 5.12)
Phillips PM2.5×4.0 Screw Locations
A–20
Maintenance and Service Guide
Screw Listing
Table A-7
Phillips PM2.0×4.0 Screw
mm
Color
Qty.
Length
Thread
Head
Width
Silver
2
4.0 mm
2.0 mm
5.0 mm
Where used:
2 screws that secure the wireless antenna transceivers to the display enclosure
(documented in Section 5.14)
Phillips PM2.0×4.0 Screw Locations
Maintenance and Service Guide
A–21
Screw Listing
Table A-8
Phillips PM2.5×2.0 Screw
mm
Color
Qty.
Length
Thread
Head
Width
Silver
3
2.0 mm
2.5 mm
6.0 mm
Where used:
3 screws that secure the top cover to the base enclosure (documented in
Section 5.15)
Phillips PM2.5×2.0 Screw Locations
A–22
Maintenance and Service Guide
B
Backup and Recovery
Recovering System Information
Tools provided by the operating system and PC Recovery
software are designed to help you with the following tasks for
safeguarding your information and restoring it in case of a
system failure:
■
Back up your information regularly to protect your important
system files.
■
Make a set of recovery discs (PC Recovery software feature).
Recovery discs are used to start up (boot) your computer and
restore the operating system and software programs to factory
settings in case of system failure or instability.
■
Create system restore points (operating system feature).
System restore points allow you to reverse undesirable
changes to your computer by restoring the computer to an
earlier state.
■
Recover a program or driver (PC Recovery software feature).
This feature helps you reinstall a program or driver without
performing a full system recovery.
■
Perform a full system recovery (PC Recovery software
feature). With PC Recovery, you can recover your full
factory image if you experience system failure or instability.
PC Recovery works from a dedicated recovery partition on
the hard drive or from recovery discs you create.
Maintenance and Service Guide
B–1
Backup and Recovery
Backing Up Your Information
When to Back Up
■
On a regularly scheduled basis.
✎ Set reminders to back up your information periodically.
■
Before the computer is repaired or restored.
■
Before you add or modify hardware or software.
Backup Suggestions
■
Create system restore points using Windows XP Professional
System Restore feature.
■
Store personal files in the My Documents folder and back up
these folders periodically.
■
Back up templates stored in their associated programs.
■
Save customized settings in a window, toolbar, or menu bar
by taking a screen shot of your settings.
The screen shot can be a time saver if you have to reset
your preferences.
To copy the screen and paste it into a Word document:
a. Display the screen.
b. Copy the screen:
To copy only the active window, press alt+fn+prt sc.
To copy the entire screen, press fn+prt sc.
c. To paste the copied images into a document, open Word,
and then select Edit > Paste.
B–2
Maintenance and Service Guide
Backup and Recovery
Using System Restore Points
When you back up your system, you are creating a system restore
point. A system restore point allows you to save and name a
snapshot of your hard drive at a specific point in time. You can
then recover back to that point if you want to reverse subsequent
changes made to your system.
to an earlier restore point does not affect data files
✎ Recovering
saved or e-mails created since the last restore point.
You also can create additional restore points to provide increased
protection for your system files and settings.
When to Create Restore Points
■
Before you add or extensively modify software or hardware.
■
Periodically, whenever the system is performing optimally.
revert to a restore point and then change your mind, you
✎ Ifcanyoureverse
the restoration.
Create a System Restore Point
1. Select Start > Help and Support > System Restore.
The System Restore window opens.
2. Click Create a restore point, and then click Next.
3. Follow the on-screen instructions.
Maintenance and Service Guide
B–3
Backup and Recovery
Restore to a Previous Date and Time
To revert to a restore point (created at a previous date and time),
when the computer was functioning optimally:
1. Select Start > Help and Support > System Restore.
The System Restore window opens.
2. Click Restore my computer to an earlier time, and then
click Next.
3. Follow the on-screen instructions.
Creating Recovery Discs
PC Recovery Disc Creator creates a set of recovery CDs or DVDs
for the computer. Use recovery discs to restore the operating
system and software programs to factory settings, in case of
system failure or instability.
these discs carefully and keep them in a safe place. The
✎ Handle
software allows the creation of only one set of recovery discs.
Note the following guidelines before creating recovery discs:
■
You will need high quality CD-R, DVD-R, or DVD+R media
(purchased separately).
and double-layer DVD±RW are not compatible
✎ DVD±RW/R
with the PC Recovery Disc Creator software.
B–4
■
The computer must be connected to AC power during
this process.
■
Only one set of recovery discs can be created per computer.
Maintenance and Service Guide
Backup and Recovery
■
Number each disc before inserting it into the computer
optical drive.
■
If necessary, you can exit the program before you have
finished creating the recovery discs. The next time you open
PC Recovery Disc Creator, you will be prompted to continue
the disc creation process.
To create a set of recovery discs:
1. Select Start > All Programs > System Recovery >
PC Recovery Disc Creator.
The PC Recovery Disc Creator tool opens.
2. Click Next.
you are operating the computer on battery power, you will be
✎ Ifprompted
to connect to AC power before you can go to the
next step.
3. Select the type of disc you want to use and click Next.
software examines the image and displays the number of
✎ The
blank discs needed to create your recovery discs.
4. Insert the first disc and follow the on-screen instructions to
complete the creation of the recovery discs.
Maintenance and Service Guide
B–5
Backup and Recovery
Reinstalling Software Programs and Drivers
If a program or driver preinstalled at the factory is accidentally
erased or is damaged, the Application and Driver Recovery tool
allows you to reinstall it.
not provided with this computer must be reinstalled
✎ Software
from the disc provided by the manufacturer or downloaded
from the manufacturer's Web site.
✎ Before reinstalling the program, be sure it is fully uninstalled.
The Application and Driver Recovery tool replaces corrupted
system files and reinstalls deleted system files within
the program.
■
In most cases, if the program you are reinstalling is still on
your computer, the reinstallation process does not affect your
personal settings.
■
In all cases, if a program has been deleted from your
computer, the reinstallation process reinstalls the program or
utility to the factory image but cannot restore your
personal settings.
Reinstalling Preinstalled Programs and
Drivers
1. Remove the program or driver:
some cases, drivers are not listed in the Add or Remove
✎ InPrograms
list. If the driver is not listed, it does not need to be
removed.
a. Select Start > Control Panel > Add or
Remove Programs.
b. Click the program or driver you want to remove, and then
click Change/Remove.
B–6
Maintenance and Service Guide
Backup and Recovery
2. Select Start > All Programs > System Recovery >
Application and Driver Recovery.
The Application and Driver Recovery tool opens.
3. Select Application Installation or Driver Installation, and
then click Next.
4. Follow the on-screen instructions to complete the program or
driver recovery.
5. Restart the computer if prompted.
Reinstalling Programs from Discs
1. Insert the disc into the optical drive.
2. When the installation wizard opens, follow the installation
instructions on the screen.
3. Restart the computer if prompted.
Performing a Recovery
PC Recovery software allows you to repair or restore the system
if you experience system failure or instability. PC Recovery
works from recovery discs that you create or from a dedicated
recovery partition on the hard drive.
Windows XP has its own built-in repair features,
✎ Microsoft
such as System Restore and driver roll-back capabilities. If you
have not already tried these features, try them before using
PC Recovery.
Recovery only recovers software that was preinstalled at
✎ PC
the factory. Software not provided with this computer must be
reinstalled from the disc provided by the manufacturer or
downloaded from the manufacturer's Web site.
Maintenance and Service Guide
B–7
Backup and Recovery
Recovering from the Recovery Discs
To restore the system from the recovery discs:
1. Back up all personal files.
2. Insert the first recovery disc into the optical drive and restart
the computer.
3. Follow the on-screen instructions.
Recovering from the Partition on the
Hard Drive
You can perform a recovery from the partition on the hard drive
from either the Start button or f11.
To restore the system from the partition:
1. Access the PC Recovery tool:
❏ To access PC Recovery from the Start button, select
Start > All Programs > System Recovery >
PC Recovery.
❏ To access PC Recovery from f11, restart the computer and
press f11 while the “Press <F11> for recovery” message is
displayed on the screen.
The PC Recovery tool opens.
2. Select PC Recovery and click Next.
The computer restarts and the PC Recovery tool opens.
3. Click OK.
4. Follow the on-screen instructions to complete the
system recovery.
B–8
Maintenance and Service Guide
Backup and Recovery
If you want to perform a destructive recovery:
destructive recovery formats the hard drive and restores the
✎ Acomputer
to its factory state. Select this option only as a
last resort.
a. Click Advanced Options on the System Recovery screen.
b. Select Destructive Recovery and follow the on-screen
instructions.
Deleting the Recovery Partition on the
Hard Drive
The PC Recovery Advanced Options menu provides the option of
deleting the recovery partition, which will increase space on the
hard drive. Delete the recovery partition only if you have already
created recovery discs.
Ä
CAUTION: After you create the recovery discs, you can increase
space on the hard drive by deleting the recovery partition. However,
doing this is not recommended. If you delete this partition, you will lose
any information that is on the partition, including the PC Recovery
software. Thereafter, you must use the recovery discs to access PC
Recovery software.
To delete the recovery partition:
1. If you have not already created recovery discs, create
them now.
2. Select Start > All Programs > System Recovery >
PC Recovery.
The PC Recovery tool opens.
3. Select PC Recovery and click Next.
The computer restarts and the PC Recovery tools opens.
Maintenance and Service Guide
B–9
Backup and Recovery
4. Click OK.
5. At the System Recovery screen, click Advanced Options.
6. Select Delete Recovery Partition (not recommended) and
follow the on-screen instructions.
Updating Reinstalled Software
After you perform a system recovery, connect to the Internet to
update all reinstalled software.
To access update links for the operating system and other
software provided on your computer:
»
Select Start > Help and Support.
To update optional software, follow the instructions provided by
the software manufacturer. Some programs include an update
feature you can access from a Help button or menu within
the program.
B–10
Maintenance and Service Guide
C
Display Component Recycling
Å
WARNING: The backlight contains mercury. Caution should be
exercised when removing and handling the backlight to avoid
damaging this component and causing exposure to the mercury.
Ä
CAUTION: The procedures in this appendix can result in damage to
display components. The only components intended for recycling
purposes are the liquid crystal display (LCD) panel and the backlight.
Careful handling should be exercised when removing these
components.
Disposal
✎ Materials
This HP product contains mercury in the display assembly
backlight and may require special handling at end-of-life.
Disposal of mercury may be regulated because of environmental
considerations. For disposal or recycling information, contact
your local authorities or visit the Electronic Industries Alliance
(EIA) at http://www.eiae.org.
Maintenance and Service Guide
C–1
Display Component Recycling
This appendix provides disassembly instructions for the display
assembly. The display assembly must be disassembled to gain
access to the backlight 1 and the LCD panel 2.
procedures differ from one display assembly to
✎ Disassembly
another. The procedures provided in this appendix are general
disassembly instructions. Specific details, such as screw sizes,
quantities, and locations, and component shapes and sizes, can
vary from one computer model to another.
Refer to Section 5.14, “Display Assembly,” for display assembly
disassembly steps.
C–2
Maintenance and Service Guide
Display Component Recycling
Perform the following steps to disassemble the display assembly:
1. Remove all screw covers 1 and screws 2 that secure the
display bezel to the display assembly.
Removing the Display Bezel Screw Covers and Screws
Maintenance and Service Guide
C–3
Display Component Recycling
2. Lift up and out on the left and right inside edges 1 and the
top and bottom inside edges 2 of the display bezel until the
bezel disengages from the display assembly.
3. Remove the display bezel 3.
Removing the Display Bezel
4. Disconnect all LCD panel cables 1 from the display inverter
board and remove the inverter board 2.
Removing the Display Inverter Board
C–4
Maintenance and Service Guide
Display Component Recycling
5. Remove all screws 1 that secure the LCD panel to the
display enclosure.
6. Remove the LCD panel 2 from the display enclosure.
Removing the LCD Panel
7. Turn the LCD panel upside down.
8. Remove all screws that secure the LCD panel frame to the
LCD panel.
Removing the LCD Panel Frame Screws
Maintenance and Service Guide
C–5
Display Component Recycling
9. Use a sharp-edged tool to cut the tape 1 that secures the side
of the LCD panel to the LCD panel frame.
10. Remove the LCD panel frame 2 from the display panel.
Removing the LCD Panel Frame
C–6
Maintenance and Service Guide
Display Component Recycling
11. Remove the screws 1 that secure the backlight cover to the
LCD panel.
12. Lift the top edge of the backlight cover 2 and swing it
forward.
13. Remove the backlight cover.
Removing the Backlight Cover
Maintenance and Service Guide
C–7
Display Component Recycling
14. Turn the LCD panel right-side up.
15. Remove the backlight cables 1 from the clip 2 in the
LCD panel.
Releasing the Backlight Cables
C–8
Maintenance and Service Guide
Display Component Recycling
16. Turn the LCD panel upside down.
17. Remove the backlight frame from the LCD panel.
Removing the Backlight Frame
Maintenance and Service Guide
C–9
Display Component Recycling
Å
WARNING: The backlight contains mercury. Caution should be
exercised when removing and handling the backlight to avoid
damaging this component and causing exposure to the mercury.
18. Slide the backlight out of the backlight frame.
Removing the Backlight
C–10
Maintenance and Service Guide
Display Component Recycling
19. Disconnect the display cable 1 from the LCD panel.
20. Remove the screws 2 that secure the LCD panel to the LCD
rear panel.
21. Release the LCD panel 3 from the LCD rear panel.
22. Release the tape 4 that secures the LCD panel to the LCD
rear panel.
Releasing the LCD Panel
Maintenance and Service Guide
C–11
Display Component Recycling
23. Remove the LCD panel.
Removing the LCD Panel
24. Recycle the backlight and LCD panel.
C–12
Maintenance and Service Guide
D
Connector Pin Assignments
Table D-1
Universal Serial Bus
Pin
Signal
Pin
Signal
1
+5 VDC
3
Data +
2
Data –
4
Ground
Maintenance and Service Guide
D–1
Connector Pin Assignments
Table D-2
RJ-45 (Network)
Pin
Signal
Pin
Signal
1
Transmit +
5
Unused
2
Transmit –
6
Receive –
3
Receive +
7
Unused
4
Unused
8
Unused
D–2
Maintenance and Service Guide
Connector Pin Assignments
Table D-3
S-Video-Out
Pin
Signal
Pin
Signal
1
TV-Ground
5
TV-CD
2
TV-CVBS
6
TV-Ground
3
TV-Ground
7
TV-YD
4
TV-Ground
Maintenance and Service Guide
D–3
Connector Pin Assignments
Table D-4
External Monitor
Pin
Signal
Pin
Signal
1
Red analog
9
+5 VDC
2
Green analog
10
Ground
3
Blue analog
11
Monitor detect
4
Not connected
12
DDC 2B data
5
Ground
13
Horizontal sync
6
Ground analog
14
Vertical sync
7
Ground analog
15
DDC 2B clock
8
Ground analog
D–4
Maintenance and Service Guide
Connector Pin Assignments
Table D-5
RJ-11 (Modem)
Pin
Signal
Pin
Signal
1
Unused
4
Unused
2
Tip
5
Unused
3
Ring
6
Unused
Maintenance and Service Guide
D–5
Connector Pin Assignments
Table D-6
Audio-In (Microphone)
Pin
Signal
Pin
Signal
1
Audio signal in
3
Ground
2
Audio signal in
Table D-7
Audio-Out (Headphone)
Pin
Signal
Pin
Signal
1
Audio out, left channel
3
Ground
2
Audio out, right channel
D–6
Maintenance and Service Guide
E
Power Cord Set Requirements
3-Conductor Power Cord Set
The wide range input feature of the computer permits it to operate
from any line voltage from 100 to 120 or 220 to 240 volts AC.
The power cord set included with the computer meets the
requirements for use in the country where the equipment
is purchased.
Power cord sets for use in other countries must meet the
requirements of the country where the computer is used.
Maintenance and Service Guide
E–1
Power Cord Set Requirements
General Requirements
The requirements listed below are applicable to all countries.
E–2
■
The length of the power cord set must be at least 1.5 m
(5.0 ft) and a maximum of 2.0 m (6.5 ft).
■
All power cord sets must be approved by an acceptable
accredited agency responsible for evaluation in the
country where the power cord set will be used.
■
The power cord sets must have a minimum current capacity
of 10 amps and a nominal voltage rating of 125 or 250 V AC,
as required by each country’s power system.
■
The appliance coupler must meet the mechanical
configuration of an EN 60 320/IEC 320 Standard Sheet C13
connector for mating with the appliance inlet on the back of
the computer.
Maintenance and Service Guide
Power Cord Set Requirements
Country-Specific Requirements
3-Conductor Power Cord Set Requirements
Country/Region
Accredited Agency
Applicable Note Number
Australia
EANSW
1
Austria
OVE
1
Belgium
CEBC
1
Canada
CSA
2
Denmark
DEMKO
1
Finland
FIMKO
1
France
UTE
1
Germany
VDE
1
Italy
IMQ
1
Japan
METI
3
✎ NOTES:
1. The flexible cord must be <HAR> Type HO5VV-F, 3-conductor, 1.0 mm²
conductor size. Power cord set fittings (appliance coupler and wall plug)
must bear the certification mark of the agency responsible for evaluation
in the country where it will be used.
2. The flexible cord must be Type SPT-3 or equivalent, No. 18 AWG,
3-conductor. The wall plug must be a two-pole grounding type with a
NEMA 5-15P (15 A, 125 V) or NEMA 6-15P (15 A, 250 V) configuration.
3. The appliance coupler, flexible cord, and wall plug must bear a “T” mark
and registration number in accordance with the Japanese Dentori Law. The
flexible cord must be Type VCT or VCTF, 3-conductor, 1.00 mm² conductor
size. The wall plug must be a two-pole grounding type with a Japanese
Industrial Standard C8303 (7 A, 125 V) configuration.
Maintenance and Service Guide
E–3
Power Cord Set Requirements
3-Conductor Power Cord Set Requirements (Continued)
Country/Region
Accredited Agency
Applicable Note Number
Korea
EK
4
The Netherlands
KEMA
1
Norway
NEMKO
1
People’s Republic
of China
CCC
5
Sweden
SEMKO
1
Switzerland
SEV
1
Taiwan
BSMI
4
United Kingdom
BSI
1
United States
UL
2
✎ NOTES:
1. The flexible cord must be <HAR> Type HO5VV-F, 3-conductor, 1.0 mm²
conductor size. Power cord set fittings (appliance coupler and wall plug)
must bear the certification mark of the agency responsible for evaluation
in the country where it will be used.
2. The flexible cord must be Type SPT-3 or equivalent, No. 18 AWG,
3-conductor. The wall plug must be a two-pole grounding type with a
NEMA 5-15P (15 A, 125 V) or NEMA 6-15P (15 A, 250 V) configuration.
3. The appliance coupler, flexible cord, and wall plug must bear a “T” mark
and registration number in accordance with the Japanese Dentori Law. The
flexible cord must be Type VCT or VCTF, 3-conductor, 1.00 mm² conductor
size. The wall plug must be a two-pole grounding type with a Japanese
Industrial Standard C8303 (7 A, 125 V) configuration.
4. The flexible cord must be Type RVV, 3-conductor, 0.75 mm² conductor size.
Power cord set fittings (appliance coupler and wall plug) must bear
the certification mark of the agency responsible for evaluation in the country
where it will be used.
5. The flexible cord must be Type VCTF, 3-conductor, 0.75 mm² conductor
size. Power cord set fittings (appliance coupler and wall plug) must bear the
certification mark of the agency responsible for evaluation in the country
where it will be used.
E–4
Maintenance and Service Guide
Index
1394 port 1–8
A
AC adapter, spare part
numbers 3–20, 3–22, 3–30
analog TV tuner, spare part
number 3–20, 3–25
arrow keys 1–11
audio board
removal 5–44
spare part numbers 3–9,
3–28, 5–44
audio board cable, removal
5–55
audio troubleshooting 2–25
audio-in (microphone) jack
location 1–6
pin assignments D–6
audio-out (headphone) jack
location 1–6
pin assignments D–6
B
base enclosure, spare part
numbers 3–9, 3–28, 3–30
battery
removal 5–4
spare part numbers 3–9,
3–29, 5–4
specifications 6–6
Maintenance and Service Guide
battery bay 1–18
battery light 1–5
battery release latch 1–18
Bluetooth module
removal 5–46
spare part number 3–7,
3–25, 5–46
bottom components 1–18
C
cables, service considerations
4–2
camera cable
removal 5–38
spare part number 3–17,
5–38
camera module
removal 5–32
spare part number 3–17,
3–26, 5–32
caps lock key 1–11
caps lock light 1–13
CMOS clearing 1–4
components
bottom 1–18
front 1–5
keyboard 1–10
left-side 1–7
rear 1–7
Index–1
Index
right-side 1–9
top 1–12, 1–14, 1–17
composite S-Video and audio
input cable, spare part
number 3–20, 3–24
computer feet, locations 5–9
Computer Setup
Advanced Menu 2–8
File Menu 2–6
Security Menu 2–6
Tools Menu 2–7
computer specifications 6–1
connector pin assignments
external monitor D–4
headphone D–6
microphone D–6
monitor D–4
RJ-11 (modem) D–5
RJ-45 (network) D–2
S-Video-out D–3
Universal Serial Bus (USB)
D–1
connectors, service
considerations 4–2
consumer infrared lens 1–6
D
design overview 1–20
Digital Media Slot 1–8
disassembly sequence chart
5–2
diskette drive, OS loading
problems 2–23
display assembly
removal 5–26
spare part numbers 3–3,
3–25, 3–29, 5–26
specifications 6–3
Index–2
display bezel
removal 5–30, 5–31
spare part numbers 3–16,
3–26, 3–30, 5–31
Display Cable Kit, spare part
number 3–17, 3–26, 5–38
display enclosure, spare part
numbers 3–17, 3–26, 3–30
display hinge
removal 5–35
spare part number 5–35
display hinge cover
removal 5–35
spare part numbers 3–17,
3–26, 3–30, 5–35
Display Hinge Kit, spare part
number 3–16, 3–26, 5–35
display panel
removal 5–34
spare part numbers 3–17,
3–25, 5–34
Display Screw Kit, spare part
number 3–17, 3–26
docking device,
troubleshooting 2–18
drive light 1–6
drives, preventing damage 4–3
DVD button 1–15
DVD/CD-RW Combo Drive
OS loading problems 2–24
precautions 4–3
removal 5–16
spare part number 3–15,
3–18, 3–26, 5–16
specifications 6–7
Maintenance and Service Guide
Index
DVD±RW/R and CD-RW
Combo Drive
OS loading problems 2–24
precautions 4–3
removal 5–16
spare part numbers 3–15,
3–18, 3–26, 3–27, 5–16
specifications 6–9
E
electrostatic discharge 4–4,
4–8
expansion port 3 1–8
ExpressCard assembly
removal 5–48
spare part number 3–7,
3–28, 5–48
ExpressCard slot 1–9
ExpressCard slot bezel
illustrated 3–19
removal 5–48
external monitor port
location 1–7
pin assignments D–4
F
fan/heat sink assembly
removal 5–56
spare part numbers 3–5,
3–29, 5–56
features 1–2
feet, locations 5–9
flowcharts, troubleshooting
no audio 2–25, 2–26
no network/modem
connection 2–30
no OS loading 2–19
Maintenance and Service Guide
no OS loading from
diskette drive 2–23
no OS loading from hard
drive 2–20, 2–21, 2–22
no OS loading from optical
drive 2–24
no power 2–12, 2–14, 2–15
no video 2–16, 2–17
nonfunctioning device
2–27
nonfunctioning docking
device 2–18
nonfunctioning keyboard
2–28
nonfunctioning pointing
device 2–29
fn key 1–11
front components 1–5
function keys 1–11
G
grounding equipment and
methods 4–7
H
hard drive
OS loading problems 2–20
precautions 4–3
removal 5–6
spare part numbers 3–9,
3–18, 3–26, 5–6
specifications 6–4
hard drive bay 1–19
hard drive cover
illustrated 3–19
removal 5–6
hard drive frame, removal 5–8
Index–3
Index
HDMI port 1–8
headphone jack
location 1–6
pin assignments D–6
headset, spare part number
3–20, 3–22
hinge
removal 5–35
spare part number 3–16,
3–26, 5–35
hinge cover
removal 5–35
spare part numbers 3–17,
5–35
HP Backpack, spare part
number 3–20, 3–22
I
I/O address specifications
6–14
interrupt specifications 6–12
inverter
removal 5–33
spare part number 3–17,
3–26, 5–33
K
keyboard
removal 5–20
spare part numbers 3–5,
3–27, 5–20
troubleshooting 2–28
keyboard components 1–10
keypad keys 1–11
L
left-side components 1–7
Logo Kit, spare part number
3–20, 3–28
Index–4
M
mass storage devices, spare
part numbers 3–18
media button 1–15
memory module
removal 5–10
spare part numbers 3–15,
3–26, 5–10
memory module compartment
1–19
memory module compartment
cover
illustrated 3–19
removal 5–10
microphone
location 1–13
removal 5–37
spare part number 3–17,
3–26, 5–37
microphone jack
location 1–6
pin assignments D–6
Mini Card module
removal 5–13
spare part numbers 3–11,
3–13, 3–15, 3–23, 3–24,
5–13, 5–14
modem jack
location 1–8
pin assignments D–5
modem, troubleshooting 2–30
monitor port
location 1–7
pin assignments D–4
mouse, spare part number
3–22
Maintenance and Service Guide
Index
N
network jack
location 1–8
pin assignments D–2
network, troubleshooting 2–30
next/fast forward button 1–16
nonfunctioning device,
troubleshooting 2–18, 2–27
num lock key 1–11
num lock light 1–13
O
optical drive
location 1–9, 1–18
OS loading problems 2–24
precautions 4–3
removal 5–16
spare part numbers 3–15,
3–18, 5–16
specifications 6–7
optical drive bracket, removal
5–17
P
packing precautions 4–5
password clearing 1–4
plastic parts 4–2
Plastics Kit
contents 3–19
spare part number 3–7,
3–19, 3–28
play/pause button 1–16
pointing device,
troubleshooting 2–29
power button 1–13
Maintenance and Service Guide
power button board
removal 5–24
spare part number 3–3,
3–28, 5–24
power connector 1–9
power cord
set requirements E–2
spare part numbers 3–21,
3–22
power light 1–5
power management features
1–4
power, troubleshooting 2–12
previous/rewind button 1–16
processor
removal 5–59
spare part numbers 3–7,
3–25, 5–59
R
rear components 1–7
remote control, spare part
number 3–20, 3–24
removal
preliminaries 4–1
procedures 5–1
replacement
preliminaries 4–1
procedures 5–1
RF cable, spare part number
3–20, 3–25
RF input adapter cable, spare
part number 3–20, 3–25
right-side components 1–9
RJ-11 (modem) jack
location 1–8
pin assignments D–5
Index–5
Index
RJ-45 (network) jack
location 1–8
pin assignments D–2
RTC battery
removal 5–12
spare part number 3–15,
3–28, 5–12
Rubber Feet Kit, spare part
number 3–9, 3–28
S
Screw Kit, spare part number
3–21, 3–28
screw listing A–1
security cable slot 1–7
serial number 3–1, 5–1
service considerations 4–2
Setup Utility 2–1
speaker assembly
removal 5–23
spare part number 3–5,
3–29, 5–23
speakers 1–13
specifications
battery 6–6
computer 6–1
display 6–3
DVD/CD-RW Combo
Drive 6–7
DVD±RW/R and CD-RW
Combo Drive 6–9
hard drive 6–4
I/O addresses 6–14
interrupts 6–12
optical drive 6–7
system DMA 6–11
static shielding materials 4–8
Index–6
stop button 1–16
S-Video-out jack
location 1–7
pin assignments D–3
switch cover
removal 5–18
spare part numbers 3–3,
3–28, 5–18
system board
removal 5–52
spare part numbers 3–7,
3–25, 3–30, 5–52
system DMA 6–11
T
tools required 4–1
top components 1–12, 1–14,
1–17
top cover
removal 5–39
spare part numbers 3–5,
3–27, 3–28, 5–39
top cover support trim
removal 5–43
spare part numbers 3–5,
3–28, 5–39
TouchPad 1–17
TouchPad buttons 1–17
TouchPad light 1–17
TouchPad on/off button 1–17
TouchPad vertical scroll zone
1–17
transporting precautions 4–5
troubleshooting
audio 2–25
docking device 2–18
flowcharts 2–9
keyboard 2–28
Maintenance and Service Guide
Index
modem 2–30
network 2–30
nonfunctioning device
2–18, 2–27
OS loading 2–19
overview 2–1
pointing device 2–29
power 2–12
video 2–16
TV tuner remote control, spare
part number 3–20, 3–25
W
Windows applications key
1–11
Windows logo key 1–11
wireless antenna
removal 5–36
spare part number 3–17,
3–26, 5–36
wireless light 1–6
wireless switch 1–6
workstation precautions 4–6
U
Universal Serial Bus (USB)
port
location 1–8, 1–9
pin assignments D–1
unknown password 1–4
USB digital drive, spare part
number 3–18, 3–22
USB infrared receiver, spare
part number 3–20, 3–25
USB travel mouse, spare part
number 3–20, 3–22
USB/power connector board
removal 5–50
spare part numbers 3–7,
3–28, 3–29, 5–50
USB/power connector cable,
removal 5–55
V
vents 1–19
video troubleshooting 2–16
volume mute button 1–13
volume scroll zone 1–13
Maintenance and Service Guide
Index–7