Daewoo DTQ-14T2FS Service manual

xystus
Service Manual
Color Television
CHASSIS :
MODEL:
CN-201A/B
NTSC-M SYSTEM
DTQ-14Q1FS, DTQ-14Q2TS
DTQ-14Q3FS, DTQ-14T1AS
DTQ-14T2FS, DTQ-20Q1FS
DTQ-20Q2FS, DTQ-20Q3FS
DTQ-20T1AS, DTQ-20T2AS
DTQ-20T1FS, DTQ-20T2FS
DTQ-20T3FS, DTQ-21T1FS
DTQ-21T2FS, DTQ-21T5FS
DTQ-21T9FS, DTQ-20T1FC
DAEWOO ELECTRONICS CO., LTD.
FEATURES
FS (Frequency Synthesizer) Tuning System
CATV Ready
High Focus Minineck CRT
ELECTRICAL SPECIFICATIONS
POWER INPUT
AC90V - AC250V
DTQ-20T1FC : 120V
POWER RATING
14” Model
20” MONO Model
20” ST Model
21” ST Model
INTERMEDIATE FREQUENCIES
PICTURE IF CARRIER FREQUENCY
SOUND IF CARRIER FREQUENCY
COLOR SUB CARRIER FREQUENCY
AUDIO OUTPUT RATING
SPEAKER
ANTENNA INPUT IMPEDANCE
TUNING RANGES
VHF
UHF
CATV
50/60Hz
60HZ ONLY
60W
70W
80W
80W
45.75MHz
41.25MHz
42.17MHz
MONO(2W) ST(3W+3W)
3W 16ohm
VHF/UHF 75 ohm UNBALANCED
2 THRU 13
14 THRU 69
1 THRU 125
CONTENTS
Safety Precautions
Control View
Important Service Notes
Block Diagram
General Adjustments
Operation Charaeteristic of Power Block
Trouble Shooting Charts
Description of Semiconductors
Printed Circuit Board Diagram
Exploded Views
Schematic Diagram with Waveforms
Parts List
Option List
3
6
8
9
10
14
22
28
32
33
50
51
65
2
PRODUCT SAFETY SERVICING GUIDELINES FOR AUDIO VIDEO PRODUCTS
CAUTION :
SUBJECT : X-RADIATION
DO NOT ATTEMPT TO MODIFY THIS PRODUCT IN ANY WAY. NEVER
PERFORM CUSTOMIZED INSTALLATIONS WITHOUT MANUFACTURER S APPROVAL.
UNAUTHORIZED MODIFICATIONS WILL NOT ONLY VOID THE WARRANTY, BUT MAY
LEAD TO YOUR BEING LIABLE FOR ANT RESULTING PROPERTY DAMAGE OR USER
INJURY.
950ART94
1009
1. BE SURE PROCEDURES AND INSTRUCTIONS TO ALL SERVICE PERSONNEL COVER
THE SUBJECT OF X-RADIATION. THE ONLY POTENTIAL SOURCE OF X-RAYS IN
CURRENT T.V. RECEIVERS IS THE PICTURE TUBE. HOWEVER, THIS TUBE DOES NOT
EMIT X-RAYS WHEN THE HIGH VOLTAGE IS AT THE FACTORY SPECIFIED LEVEL. THE
PROPER VALUE IS GIVEN IN THE APPLICABLE SCHEMATIC. OPERATION AT HIGHER
VOLTAGES MAY CAUSE A FAILURE OF THE PICTURE TUBE OR HIGH VOLTAGE
SUPPLY AND, UNDER CERTAIN CIRCUMSTANCES, AMY PRODUCE RADIATION IN
EXCESS OF DESIRABLE LEVELS.
SERVICE WORK SHOULD BE PERFORMED ONLY AFTER YOU ARE THOROUGHLY
FAMILIAR WITH ALL OF THE FOLLOWING SAFETY CHECKS AND SERVICING
GUIDELINES. TO DO OTHERWISE, INCREASES THE RISK OF POTENTIAL HAZARDS AND
INJURY TO THE USER.
WHILE SERVICING, USE AN ISOLATION TRANSFORMER FOR PROTECTION FROM A.C.
LINE SHOCK.
2. ONLY FACTORY SPECIFIED C.R.T ANODE CONNECTORS MUST BE USED.
DEGAUSSING SHIELDS ALSO SERVE AS X-RAY SHIELD IN COLOR SETS. ALWAYS REINSTALL THEM.
SAFETY CHECKS
AFTER THE ORIGINAL SERVICE PROBLEM HAS BEEN CORRECTED, A CHECK SHOULD
BE MADE OF THE FOLLOWING:
3. IT IS ESSENTIAL THAT SERVICE PERSONNEL HAVE AVAILABLE AN ACCURATE AND
RELIABLE HIGH VOLTAGE METER. THE CALIBRATION OF THE METER SHOULD BE
CHECKED PERIODICALLY AGAINST A REFERENCE STANDARD. SUCH AS THE ONE
AVAILABLE AT YOUR DISTRIBUTOR.
SUBJECT:FIRE & SHOCK HAZARD
1. BE SURE THAT ALL COMPONENTS ARE POSITIONED IN SUCH A WAY AS TO AVOID
POSSIBILITY OF ADJACENT COMPONENT SHORTS. THIS IS ESPECIALLY IMPORTANT
ON THOSE MODULES WHICH ARE TRANSPORTED TO AND FROM THE REPAIR SHOP.
4. WHEN THE HIGH VOLTAGE CIRCUITRY IS OPERATING PROPERLY THERE IS NO
POSSIBILITY OF AN X-RADIATION PROBLEM. EVERY TIME A COLOR CHASSIS IS
SERVICED, THE BRIGHTNESS SHOULD BE RUN UP AND DOWN WHILE MONITORING
THE HIGH VOLTAGE WITH A METER TO BE CERTAIN THAT THE HIGH VOLTAGE DOES
NOT EXCEED THE SPECIFIED VALUE AND THAT IT IS REGULATING CORRECTLY. WE
SUGGEST THAT YOU AND YOUR SERVICE ORGANIZATION REVIEW TEST
PROCEDURES SO THAT VOLTAGE REGULATION IS ALWAYS CHECKED AS A
STANDARD SERVICING PROCEDURE, AND THAT THE HIGH VOLTAGE READING BE
RECORDED ON EACH CUSTOMER S INVOICE.
2. NEVER RELEASE A REPAIR UNLESS ALL PROTECTIVE DEVICES SUCH AS
INSULATORS, BARRIERS, COVERS, SHIELDS, STRAIN RELIEFS, POWER SUPPLY
CORDS, AND OTHER HARDWARE HAVE BEEN REINSTALLED PER ORIGINAL DESIGN.
BE SURE, THAT THE SAFETY PURPOSE OF THE POLARIZED LINE PLUG HAS NOT
BEEN DEFEATED.
3. SOLDERING MUST BE INSPECTED TO DISCOVER POSSIBLE COLD SOLDER JOINTS,
SOLDER SPLASHES OF SHARP SOLDER POINTS. BE CERTAIN TO REMOVE ALL
LOOSE FOREIGN PARTICLES.
5. WHEN TROUBLESHOOTING AND MAKING TEST MEASUREMENTS IN A PRODUCT WITH
A PROBLEM OF EXCESSIVE HIGH VOLTAGE, AVOID BEING UNNECESSARILY CLOSE
TO THE PICTURE TUBE AND THE HIGH VOLTAGE SUPPLY. DO NOT OPERATE THE
PRODUCT LONGER THAN IS NECESSARY TO LOCATE THE CAUSE OF EXCESSIVE
VOLTAGE.
4. CHECK FOR PHYSICAL EVIDENCE OF DAMAGE OR DETERIORATION TO PARTS AND
COMPONENTS, FOR FRAYED LEADS, DAMAGED INSULATION (INCLUDING A.C. CORD),
AND REPLACE IF NECESSARY. FOLLOW ORIGINAL LAYOUT, LEAD LENGTH AND
DRESS.
5. NO LEAD OR COMPONENT SHOULD TOUCH A RECEIVING TUBE OR A RESISTOR
RATED AT 1 WATT OR MORE. LEAD TENSION AROUND PROTRUDING METAL
SURFACES MUST BE AVOIDED.
6. REFER TO HV, B + AND SHUTDOWN ADJUSTMENT PROCEDURES DESCRIBED IN THE
APPROPRIATE SCHEMATIC AND DIAGRAMS (WHERE USED).
6. ALL CRITICAL COMPONENTS SUCH AS FUSES, FLAMEPROOF RESISTOR,
CAPACITORS, ETC. MUST BE REPLACED WITH EXACT FACTORY TYPES. DO NOT USE
REPLACEMENT COMPONENTS OTHER THAN THOSE SPECIFIED OR MAKE
UNRECOMMENDED CIRCUIT MODIFICATIONS.
SUBJECT : IMPLOSION
1. ALL DIRECT VIEWED PICTURE TUBES ARE EQUIPPED WITH AN INTEGRAL IMPLOSION
PROTECTION SYSTEM. BUT CARE SHOULD BE TAKEN TO AVOID DAMAGE DURING
INSTALLATION. AVOID SCRATCHING THE TUBE. OF SCRATCHED REPLACE IT.
7. AFTER RE-ASSEMBLY OF THE STE ALWAYS PERFORM AN A.C. LEAKAGE TEST ON
ALL EXPOSED METALLIC PARTS OF THE CABINET. (THE CHANNEL SELECTOR KNOB,
ANTENNA TERMINALS, HANDLE AND SCREWS) TO BE SURE THE SET IS SAFE TO
OPERATE WITHOUT DANGER OF ELECTRICAL SHOCK. DO NOT USE A LINE
ISOLATION TRANSFORMER DURING THIS TEST USE AN A.C. VOLTMETER,
HAVING 5000 OHMS PER VOLT OR MORE SENSITIVITY, IN THE FOLLOWING MANNER :
CONNECT A 1500 OHM 10 WATT RESISTOR, PARALLELED BY A .15 MFD. 150V A.C.
TYPE CAPACITOR BETWEEN A KNOWN GOOD EARTH GROUND (WATER POPE,
CONDUIT, ETC.) AND THE EXPOSED METALLIC PARTS, ONE AT A TIME. MEASURE
THE A.C. VOLTAGE ACROSS THE COMBINATION OF 1500 OHM RESISTOR AND .15
MFD CAPACITOR. REVERSE THE A.C. PLUG AND REPEAT A.C. VOLTAGE
MEASUREMENTS FOR EACH EXPOSED METALLIC PART. VOLTAGE MEASURED MUST
NOT EXCEED .75 VOLTS R.M.S THIS CORRESPONDS TO 0.5 MILLIAMP A.C. NAY VALUE
EXCEEDING THIS LIMIT CONSTITUTES A POTENTIAL SHOCK HAZARD AND MUST BE
CORRECTED IMMEDIATELY.
2. USE ONLY RECOMMENDED FACTORY REPLACEMENT TUBES.
SUBJECT : TIPS ON PROPER INSTALLATION
1. NEVER INSTALL ANY PRODUCT IN A CLOSED-IN RECESS, CUBBYHOLE OR CLOSELY
FITTING SHELF SPACE, OVER OR CLOSE TO HEAT DUCT, OR IN THE PATH OF
HEATED AIR FLOW.
2. AVOID CONDITIONS OF HIGH HUMIDITY SUCH AS: OUTDOOR PATIO INSTALLATIONS
WHERE DEW IS A FACTOR, NEAR STEAM RADIATORS WHERE STEAM LEAKAGE IS A
FACTOR, ETC.
A.C. VOLTMETER
3. AVOID PLACEMENT WHERE DRAPERIES MAY OBSTRUCT REAR VENTING. THE
CUSTOMER SHOULD ALSO AVOID THE USE OF DECORATIVE SCARVES OR OTHER
COVERINGS WHICH MIGHT OBSTRUCT VENTILATION.
0.15µF
4. WALL AND SHELF MOUNTED INSTALLATIONS USING A COMMERCIAL MOUNTING KIT,
MUST FOLLOW THE FACTORY APPROVED MOUNTING INSTRUCTIONS. A PRODUCT
MOUNTED TO A SHELF OR PLATFORM MUST RETAIN ITS ORIGINAL FEET (OR THE
EQUIVALENT THICKNESS IN SPACERS)TO PROVIDE ADEQUATE AIR FLOW ACROSS
THE BOTTOM, BOLTS OR SCREWS USED FOR FASTENERS MUST NOT TOUCH ANY
PARTS OR WIRING. PERFORM LEAKAGE TEST ON CUSTOMIZED INSTALLATIONS.
A.C. VOLTMETER
GOOD EARTH GROUND
SUCH AS THE WATER
PIPE, CONDUIT, ETC.
1500
OHM
10WATT
PLACE THIS PROBE
ON EACH EXPOSED
METAL PART
5. CAUTION CUSTOMERS AGAINST THE MOUNTING OF A PRODUCT ON SLOPING SHELF
OR A TILTED POSITION, UNLESS THE PRODUCT IS PROPERLY SECURED.
SUBJECT : GRAPHIC SYMBOLS
6. A PRODUCT ON A ROLL-ABOUT CART SHOULD BE STABLE ON ITS MOUNTING TO THE
CART. CAUTION THE CUSTOMER ON THE HAZARDS OF TRYING TO ROLL A CART
WITH SMALL CASTERS ACROSS THRESHOLDS OR DEEP PILE CARPETS.
THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN
AN EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THE
SERVICE PERSONNEL TO THE PRESENCE OF UNINSULATED
DANGEROUS VOLTAGE THAT MAY BE OF SUFFICIENT
MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK.
7. CAUTION CUSTOMERS AGAINST THE USE OF A CART OR STAND WHICH HAS NOT
BEEN LISTED BY UNDERWRITERS LABORATORIES. INC. FOR USE WITH THEIR
SPECIFIC MODEL OF TELEVISION RECEIVER OR GENERICALLY APPROVED FOR USE
WITH T.V.S OF THE SAME OR LARGER SCREEN SIZE.
THE EXCLAMATION POINT WITHIN AN EQUILATERAL
TRIANGLE IS INTENDED TO ALERT THE SERVICE
PERSONNEL TO THE PRESENCE OF IMPORTANT SAFETY
INFORMATION ON SERVICE LITERATURE.
8. CAUTION CUSTOMERS AGAINST THE USE OF EXTENSION CORDS, EXPLAIN THAT A
FOREST OF EXTENSIONS SPROUTING FROM A SINGLE OUTLET CAN LEAD TO
DISASTROUS CONSEQUENCES TO HOME AND FAMILY.
3
Product safety servicing guidelines for color
television receivers
A.C. VOLTMETER
CAUTION : Do not attempt to modify this product in any
way. Unauthorized modifications will not only void the
warranty, but may lead to your being liable for any
resulting property damage or user injury.
Service work should be performed only after you are
thoroughly familiar with all of the following safety checks
and servicing guidelines. To do otherwise, increases the
risk of potential hazards and injury to the user.
Good earth ground,
such as the water
pipe, conduit, etc.
0.15µF
•
•
1500
OHM
10WATT
SAFETY CHECKS
After the original service problem has been corrected, a
check should be made of the following:
Place this probe
on each exposed
metal part.
GRAPHIC SYMBOLS :
1. Be sure that all components are positioned in such a
way as to avoid possibility of adjacent component
shorts. This is especially important on those chassis
which are transported to and from the repair shop.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the service personnel to the presence
of uninsulated dangerous voltage that
may be of sufficienty magnitude to
constitute a risk of electric shock.
2. Never release a repair unless all protective devices
such as insulators, barriers, covers, shields, strain
reliefs, and other hardware have been reinstalled per
original design.
The exclamation point within an equilateral
triangle is intended to alert the service
personnel to the presence of important
safety information in service literature.
SUBJECT : FIRE & SHOCK HAZARD
3. Soldering must be inspected to discover possible cold
solder joints, frayed leads, damaged insulation
(including A.C. cord), solder splashes or sharp solder
points. Be certain to remove all loose foreign particals.
Fuse symbol is printed on pcb adjacent to
the fuse, with RISK OF FIRE REPLACE
FUSE AS MARKED . The symbol is
explained in the service manual with the
following wording or equivalent.
CAUTION : FOR CONTINUED PROTECTION AGAINST
FIRE HAZARD, REPLACE ONLY WITH SAME TYPE 4A,
125V FUSE and ATTENTION: AFIN D ASSU UNE
PROTECTION PERMANENTE CONTRE LES RISQUES
D INCENDIE, REMPLACER UNIQUEMENT PAR UN
FUSIBLE DE MEME TYPE ET DE 4A, 125V .
4. Check for physical evidence of damage or deterioration
to parts and components, and replace if necessary
follow original layout, lead length and dress.
5. No leads or components should touch a receiving tube
or a resistor rated at 1 watt or more. Lead tension
around protruding metal surfaces must be avoided.
6. All critical components such as fuses, flameproof
resistors, capacitors, etc. must be replaced with exact
factory types. Do not use replacement components
other than those specified or make unrecommended
circuit modifications.
SUBJECT : X-RADIATION
1. Be sure procedures and instructions to all service
personnel cover the subject of X-rays in current T.V.
receivers is the picture tube. However, this tube does
not emit X-rays when the high voltage is at the factory
specified level. The proper value is given in the
applicable schematic. Operation at higher voltages may
cause a failure of the picture tube or high voltage
supply and, under certain circumstances, may produce
radiation in excess of desirable levels.
7. After re-assembly of the set always perform an A.C.
leakage test on all exposed metallic parts of the
cabinet, (the channel selector knob, antenna terminals,
handle and screws) to be sure the set is safe to operate
without danger of electrical shock. Do not use a line
isolation transformer during this test. Use an A.C.
voltmeter, having 5000 ohms per volt or more
sensitivity, in the following manner : connect a 1500
ohm 10 watt resistor, paralleled by a 15 mfd. 150V A.C.
type capacitor between a known good earth ground
(9water pipe, conduit, etc.) and the exposed metallic
parts, one at a time. Measure the A.C. voltage across
the combination of 1500 ohm resistor and 0.15 MFD
capacitor. Reverse the A.C. plug and repeat A.C.
voltage measurements for each exposed metallic part.
Voltage measured must not exceed 0.75 volts R.M.S.
This corresponds to 0.5 milliamp A.C. Any value
exceeding this limit constitutes a potential shock hazard
and must be corrected immediately.
2. Only factory specified C.R.T. anode connectors must
be used. Degaussing shields also serve as X-ray shield
in color sets. Always re-install them.
3. It is essential that the serviceman has available an
accurate and reliable high voltage meter. The
calibration of the meter should be checked perio dically against a reference standard. Such as the one
available at your distributor.
4. When the high voltage circuitry is operating properly
there is no possibility of an X-radiation problem. Every
time a color chassis is serviced, the brightness should
be run up and down while monitoring the high voltage
4
with a meter to be certain that the high voltage does not
exceed the specified value and that it is regulating
correctly. We suggest that you and your service
organization review test procedures so that voltage
regulation is always checked as a standard servicing
procedure. And that the high voltage reading be recorded
on each customer s invoice.
2. Avoid conditions of high humidity such as : Outdoor
patio installations where dew is a factor. Near steam
radiators where steam leakage is a factor, etc.
3. Avoid placement where draperies may obstruct rear
venting. The customer should also avoid the use of
decorative scarves or other coverings which might
obstruct ventilation.
5. When troubleshooting and making test measurements
in a receiver with a problem of excessive high voltage,
avoid being unnecessarily close to the picture tube and
the high voltage compartment.
Do not operate the chassis longer than is necessary to
locate the cause of excessive voltage.
4. Wall and shelf mounted installations using a
commercial mounting kit, must follow the factory
approved mounting instructions. A receiver mounted to
a shelf or platform must retain its original feet(or the
equivalent thickness in spacers) to provide adequate
are flow across the bottom, bolts or screws used for
fasteners must not touch and parts or wiring. Perform
leakage test on customized installations.
6. Refer to HV, B+and Shutdown adjustment procedures
described in the appropriate schematic and
diagrams(where used).
5. Caution customers against the mounting of a receiver
on sloping shelf or a tilted position, unless the receiver
is properly secured.
SUBJECT : IMPLOSION
1. All direct viewed picture tubes are equipped with an
integral implosion protection system, but care should be
taken to avoid damage during installation. Avoid
scratching the tube. If scratched, replace it.
6. A receiver on a roll-about cart should be stable on its
mounting to the cart. Caution the customer on the
hazards of trying to roll a cart with small casters across
thresholds or deep pile carpets.
2. Use only recommended factory replacement tubes.
7. Caution customers against the use of a cart or stand
which has not been listed by underwriters laboratories,
inc. For use with their specific model of television
receiver or generically approved for use with T.V. s of
the same or larger screen size.
SUBJECT : TIPS ON PROPER
INSTALLATION
1. Never install any receiver in closed-in recess,
cubbyhole or closely fitting shelf space over, or close to
heat duct, or in the path of heated air flow.
5
CONTROL VIEW
STEREO MODEL
MONO MODEL
Overview of Your Equipment
Your TV comes with a remote control. The section below summarizes the buttons, controls, and terminals that you
will use with your TV.
Your TV's Front Panel
1 POWER
Use this button to turn your TV on or off.
2 VIDEO IN jack
Use this jack to receive a video signal from another A/V component.
3 AUDIO IN jack
MONO MODEL use this jack to receive an audio signal from another A/V component. But, STEREO MODEL use
this jack to receive audio L/R signal from another A/V component.
4 EARPHONE IN jack
Use this jack to receive a audio signal from your TV.
5 STAND-BY (red) indicator
This indicator lights up when the power is off.
6 Remote control receiver
This receiver receives a signal from your remote control. Don’t block it.
7
CH
Use these buttons to change channels on your TV, or to select items in the menu system.
8
VOL
Use these buttons to change your TV’s volume, to activate selections in the menu system, or to change audio and
video settings.
9 MENU
Use this button to turn the TV’s menu system on and off.
MONO MODEL
POWER
VIDEO AUDIO EARPHONE STAND-BY
CH
VOL
MENU
CH
VOL
MENU
STEREO MODEL
AUDIO
POWER
VIDEO L
R EARPHONE STAND-BY
6
REMOTE CONTROL UNIT
1 POWER
Use this button to turn your TV on or off.
2
Use these buttons to change channels on your TV, or select items in
1
the menu system.
3
2
CH
VOL
Use these buttons to change your TV's volume, to activate selections
in the menu system, or to change audio and video settings.
3
4
3
4 MENU
Use this button to turn the TV's menu system on and off.
5 RECALL
2
Press this button to display the channel number.
6 ADD/ERA.
5
6
7
Use this button to add a channel to the TV's memory or erase the
channel from memory.
7 MUTE
Use to turn the TV's sound on and off.
8 0-9
8
Use these buttons to change channels.
9 SLEEP
Use this button to program the TV to turn off after a certain time.
9
10
11
13
10 PREV. CH
Press this button to return to the previous channel you were watching. If you have set Favorite Ch, this key operates to Favorite function.
12
11 TV/VIDEO
Use this button to select TV or VIDEO mode.
12 AUTO. PICT
Press this button to return the TV's video settings to their original
level.
13 AIR/CABLE
Use the button to set up your TV to receive signals from an antenna
(AIR) or a cable system (CABLE).
7
CONTROL VIEW
STEREO MODEL
MONO MODEL
Overview of Your Equipment
Your TV comes with a remote control. The section below summarizes the buttons, controls, and terminals that you
will use with your TV.
Your TV's Front Panel
1 POWER
Use this button to turn your TV on or off.
2 VIDEO IN jack
Use this jack to receive a video signal from another A/V component.
3 AUDIO IN jack
MONO MODEL use this jack to receive an audio signal from another A/V component. But, STEREO MODEL use
this jack to receive audio L/R signal from another A/V component.
4 EARPHONE IN jack
Use this jack to receive a audio signal from your TV.
5 STAND-BY (red) indicator
This indicator lights up when the power is off.
6 Remote control receiver
This receiver receives a signal from your remote control. Don’t block it.
7
CH
Use these buttons to change channels on your TV, or to select items in the menu system.
8
VOL
Use these buttons to change your TV’s volume, to activate selections in the menu system, or to change audio and
video settings.
9 MENU
Use this button to turn the TV’s menu system on and off.
MONO MODEL
POWER
VIDEO AUDIO EARPHONE STAND-BY
CH
VOL
MENU
CH
VOL
MENU
STEREO MODEL
AUDIO
POWER
VIDEO L
R EARPHONE STAND-BY
6
REMOTE CONTROL UNIT
1 POWER
Use this button to turn your TV on or off.
2
Use these buttons to change channels on your TV, or select items in
1
the menu system.
3
2
CH
VOL
Use these buttons to change your TV's volume, to activate selections
in the menu system, or to change audio and video settings.
3
4
3
4 MENU
Use this button to turn the TV's menu system on and off.
5 RECALL
2
Press this button to display the channel number.
6 ADD/ERA.
5
6
7
Use this button to add a channel to the TV's memory or erase the
channel from memory.
7 MUTE
Use to turn the TV's sound on and off.
8 0-9
8
Use these buttons to change channels.
9 SLEEP
Use this button to program the TV to turn off after a certain time.
9
10
11
13
10 PREV. CH
Press this button to return to the previous channel you were watching. If you have set Favorite Ch, this key operates to Favorite function.
12
11 TV/VIDEO
Use this button to select TV or VIDEO mode.
12 AUTO. PICT
Press this button to return the TV's video settings to their original
level.
13 AIR/CABLE
Use the button to set up your TV to receive signals from an antenna
(AIR) or a cable system (CABLE).
7
IMPORTANT SERVICE NOTES
tion transformer during this check). Use an AC
voltmeter having 5000 ohms per volt or more sensitivity in the following manner.
1. X-RAY RADIATION PRECAUTION
1) Excessive high voltage can produce potentially
hazardous X-RAY RADIATION. To avoid such hazards,
the high voltage must not be above the specified limit.
The nominal value of the high voltage of this receiver is
24.4kv at zero beam current (minimum brightness)
under a 120V AC power source. The high voltage must
not, under any circumstances, exceed 27kv (28.5kv).
Each time a receiver requires servicing, the high
voltage should be checked following the HIGH
VOLTAGE CHECK procedure on page 6 of this
manual. It is recommended as a parts of the service
record. It is important to use an accurate and reliable
high voltage meter.
Connect at 1500 ohm 10 watt resistor, paralleled by a
0.15 mfd. AC type capacitor, between a known good
earth ground (water pipe, conduit etc.) and the exposed
metallic parts, one at a time. Measure the AC voltage
across the combination of 1500 ohm resistor and 0.15
mfd capacitor. Voltage measured must not exceed 0.3
volts RMS. This corresponds to 0.2 millliamp. AC. Any
value exceeding the limit constitutes a potential shock
hazard and must be corrected immediately.
2) This receiver is equipped with X-RADIATION
PROTECTION circuit which prevents the receiver from
producing an excessively high voltage even if the
B+voltage increases abnormally. Each time the
receiver is serviced, X-RADIATION PROTECTION
circuit must be checked to determine that the circuit is
properly functioning, following the X-RADIATION
PROTECTION CIRCUIT CHECK procedure on page 6
of this manual.
AC VOLT METER
0.15MFD
3) The only source of X-RAY RADIATION in this TV
receiver is the picture tube. For continued X-RAY
RADIATION protection, the replacement tube must be
exactly the same type tube as specified in the parts list.
Good earth ground
such as d water
pipe, conduit, etc.
4) Some parts in this receiver have special safety-related
characteristics for X-RAY RADIATION protection. For
continued safety, parts replacement should be
undertaken only after referring to the PRODUCT
SAFETY NOTICE below.
1500 ohm
10watt
Place this probe
on each exposed
metallic part.
3. PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have
special safety-related characteristics. These
characteristics are often passed unnoticed by a visual
inspection and the protection afforded by them cannot
necessarily be obtained by using replacement
components rated for higher voltage, wattage, etc.
Replacement parts which have these special safety
characteristics are identified in this manual and its
supplements; electrical components having such features
are identified by shading on the schematic diagram and
the parts list.
Before replacing any of these components, read the parts
list in this manual carefully. The use of substitute
replacement parts which do not have the same safety
characteristics as specified in the parts list may create Xray radiation or other hazards.
2. SAFETY PRECAUTION
WARNING : Service should not be attempted by anyone
unfamiliar with the necessary precaution on this receiver.
The following are the necessary precaution to be
observed before servicing.
1) Since the chassis of this receiver has hazardous
potential to ground whenever the receiver is plugged in
(floating chassis), an isolation transformer must be
used during servicing to avoid shock hazard.
2) Always discharge the picture tube anode to the CRT
conductive coating the picture tube. The picture tube is
highly evacuated and if broken, glass fragments will be
violently expelled. Use shatterproof goggles and keep
picture tube away from the body while handling.
4. SERVICE NOTES
1) When replacing parts or circuit boards, clamp or bend
the lead wires to terminals before soldering.
3) When placing chassis in the cabinet, always be certain
that all the protective devices are put back in place,
such as; nonmetallic control knobs, insulating covers,
shields, isolation resistor-capacitor network, etc.
2) When replacing a high wattage resistor (metal oxide
film resistor) in the circuit board, keep the resistor min
1/2 inch away form circuit board.
3) Keep wires away from high voltage or high temperature
components.
4) Before returning the set to the customer, always
perform an AC leakage current check on the exposed
metallic parts of the cabinet, such as antennas,
terminals, screw-heads, metal overlays, control shafts
etc. to be sure the set is safe to operate without
danger of electrical shock. Plug the AC line cord
directly into a 120V AC outlet (do not use a line isolaMinimum brightness
8
9
GENERAL ADJUSTMENTS
1. GENERAL
7. X-RADIATION PROTECTION CIRCUIT TEST
In the majority of cases, all color televisions will need only
slight touch-up adjustment upon installation. Check the
basic characteristics such as height, focus and sub- basic
characteristics such as height, focus and sub- bright.
Observe the picture for good black and white details
without objectionable color shading. If color shading is
evident, demagnetize the receiver. If color shading still
persists, perform purity and convergence adjustments.
This should be all that is necessary to achieve Optimum
receiver performance.
When service has been performed on the horizontal
deflection system, high voltage system or B+system. the
X-RADIATION protection circuit must be tested for proper
operation as follows:
1) Operate receiver for at least 15 minutes at 120V AC
line.
2) Adjust all customer controls for normal picture and
sound.
3) Short R411(X-RAY Short test), and remove short clip.
4) If the operation of horizontal osc. does not stop in step
The circuit must be repaired, before the set is returned
to the customer.
2. SCREEN ADJUSTMENT
1) Turn on TV
2) Press the S2 key of Service Remocon to make the One
Horizontal Line
8. White balance ADJUSTMENT
1) Press the S8 key of SERVICE REMOCON, select W/B
3) Adjust the Screen adj. VR of FBT so that the One
Horizontal Line may be cut off.
4) Press the S2 key of Servic Remocon to be normal.
2) Adjust the R/G/B BIAS of Low BEAM in order that the
R/G/B BIAS of Low BEAM may meet with coordinates.
3. FOCUS ADJUSTMENT
3) Adjust the R/B DRIVE of High BEAM in order that the
R/B DRIVE of High BEAM may meet with coordinates.
1) Receive the Retma Pattern.
4) Confirm the LOW BEAM, HIGH BEAM alternately.
2) Adjust the FOCUS adj. VR to optain the clearest
picture.
5) Press the RECALL key to store.
9. SUB-BRIGHTNESS ADJUSTMENT
4. HORIZONTAL CENTER ADJUSTMENT
1) Receive the Retma Pattern.
1) Receive the Retma Pattern.
2) Press the S9(5CH) key of Service Remocon, adjust
Bright in order that the gradation pattern may set 18%.
2) Press the S6(59H) key of Service Remocon, select
H.Phase, then adjust step so that the L/R Width of
picture be alike.
3) Press the RECALL key to store.
4) Initial value of D.P :25
3) Press the RECALL key to store.
4) Initial value of D.P : 5
5. VERTICAL CENTER ADJUSTMENT
1) Receive the Retma Pattern.
2) Press the S6(59H) key of Service Remocon, select
V.DC, then adjust V.DC so that the horizontal line of
RETMA PATTERN’S center may meet with the
mechanical CENTER of CRT.
3) Press the RECAL key to store.
4) Initial value of D.P:35
6. VERTICAL HIGHT ADJUSTMENT
1) Receive the Retma Pattern.
2) Press the S6(59H) key of Service Remocon, select
V.Size, then adjust V.Size so that the center of
circumference of big circle may meet with the upper
and lower sides of the screen.
3) Press the RECALL key to store.
4) Initial of value of D.P :35
10
ASSEMBLY
8) Check the purity of the red and blue raster by adjusting
the BIAS controls.
If Convergence magnet assembly and rubber wedges
need mechanical positioning follow figure 2.
9) Obtain a white raster, referring to White Bodance
ADJUSTMENT
10. CONVERGENCE
POSITIONING
MAGNET
10) Proceed with convergence adjustment.
10-1. COLOR PURITY ADJUSTMENT
NOTE : Before attempting any purity adjustments, the
receiver should be operated for at least 15
minutes.
1) Demagnetize the picture tube with a degaussing coil.
2) Adjust the CONTRAST and BRIGHTNESS controls to
maximum
3) Adjust RED and BLUE Bias controls Service Remocon
to provide only a green raster. Adjust the GREEN BIAS
control Service Remocon if necessary.
4) Loosen the clamp screw holding the yoke, and slide the
yoke backward to provide vertical green belt(zone)in
the picture screen.
5) Remove the Rubber Wedges.
6) Rotate and spread the tabs of the purity magnet (See
figure 2) around the neck of the picture tube until the
green belt is in the center of the screen. At the same
time, center the raster vertically.
7) Move the yoke slowly forward until a uniform green
screen is obtained. Tighten the clamp screw of the yoke
temporarily.
DEFLECTION
YOKE
CONVERGENCE
MAGNET ASS'Y
TEMPORARY
MOUNTING
RUBBER
WEDGES
30
30
RUBBER
WEDGES
ADHESIVE
30
PICTURE TUBE
GLASS CLOTH
TAPE
Fig. 2 Rubber Wedges Location
11
DEF.
YOKE
10-2. CONVERGENCE ADJUSTMENTS
B. CIRCUMFERENCE CONVERGENCE ADJUSTMENT
NOTE : Before attempting any purity adjustments, the
NOTE : This adjustment requires Rubber Wedge Kit.
receiver should be operated for at least 15
minutes.
1) Loosen the clamping screw on deflection yoke to allow
the yoke to tilt.
A. CENTER CONVERGENCE ADJUSTMENT
2) Place a wedge as shown in figure 2 temporarily. (Do
not remove cover paper on adhesive part of the
wedge.)
1) Receive crosshatch pattern with a crosshatch signal
generator.
3) Tilt front of the deflection yoke up or down to obtain
better convergence in circumference. (See Fig. 4) Push
the mounting wedge into the space between picture
and the yoke to hold the yoke temporarily.
2) Adjust the BRIGHTNESS and CONTRAST Controls for
a good picture.
3) Adjust two tabs of the 4-Pole Magnets to change the
angle between them (See Fig. 3) and superimpose red
and blue vertical lines in the center area of the picture
screen. (See Fig. 4)
4) Place other wedge into bottom space and remove the
cover paper to stick.
5) Tilt front of the yoke right or left to obtain better
convergence in cicumference. (See Fig. 4)
4) Turn both tabs at the same time keeping their angles
constant to superimpose red and blue horizontal lines
at the center of the screen. (See Fig. 4)
6) Hold the yoke position and put another wedge in either
upper space. Remove cover paper and stick the wedge
on picture tube to hold the yoke.
5) Adjust two tabs of 6-Pole Magnets to superimpose
red/blue line with green on top of each other. Adjusting
the angle affects the vertical lines and rotating both
magnets affects the horizontal lines.
7) Detach the temporarily mounted wedge and put it in
another upper space. Stick it on picture tube to fix the
yoke.
6) Repeat adjustments 3), 4), 5) keeping in mind red,
green and blue movement, because 4-Pole Magnets
and 6-Pole Magnets interact and make dot movement
complex.
8) After placing three wedges, re-check overall
convergence. Tighten the screw firmly to hold the yoke
tightly in place.
9) Stick 3 adhesive tapes on wedges as shown in figure32.
4-POLE
MAGNETS
CONSTANT
4DJUST THE
ANGLE
(VERTICAL
LINES)
PURITY
MAGNETS
ROTATE TWO TABS AT
THE SAME TIME
(HORIZONTAL LINES)
CONVERGENCE MAGNET ASSEMBLY
ADJUSTMENT OF MAGNET
Fig. 3
BLUE RED
RED/BLUE GRN
B
G
R
B G R
BLUE
RED/BLUE
RED
GRN
R
B
G
G
B
R
BGR
R G B
4-Pole Magnets Movement
BGR
R
G
B
6-Pole Magnets Movement Incline the Yoke up(or down) Incline the Yoke right(or left)
Center Convergence by Convergence Magnets
Circumference Convergence by DEF. Yoke
Fig. 4 Dot Movement Pattern
12
11. APC DET & PLL Tunning ADJUSTMENT
1) Receive the signal of RF 100% Full Color bar 85dBuV.
2) Press the S5(58H) key of Service Remocon, then execute Auto adj Start.
3) Confirm the OSD of Auto adj. OK.
4) If it was Auto adj. NG, Receive the signal of adjacent channel, then perform Auto adj. Start again.
5) Press the RECALL key to store. (Initial value of D.P APC:30, PLL:40)
12. RF AGC ADJUSTMENT
1) Receive the attenuate signal of RF 100% Full Color Bar 60dBuV.
2) Connect Scope to TP101(OR P101).
3) Press the S5 key of Service Remocon, select RF AGC.D, then adjust the maximum voltage of Scope to attenuate 1V.
(Initial value of the maximum voltage : About 7V)
For example if initial maximum voltage is 7V, adjust it to 6V
4) Press the RECALL key to store. (Initial value of D.P :25)
13). Stereo/Sap ADJUSTMENT
1) Receive the ZENITH MTS signal of 1KHz(OR 3KHz)CH.
2) Press the S10(5D) key of Service Remocon, select Auto Off, then execute Auto on.
3) Press the RECALL key to store.
4) Slect L ONLY OR R ONLY Channel, then confirm stereo Seperation.
If you have only User Remocon, A way of using is as follows;
1) Press the 1 key
2) Press the MUTE key
3) Press the RECALL Key
4) Press the MUTE key then the Service mode will appear.
5) Use the CH buttons to select the mode you wish to adjust.
1
MUTE
RECALL
MUTE
13
OPERATION CHARACTERISTICS OF POWER BLOCK(I801)
This chassis designed for free voltage(AC 100V ~ AC 220V) power. power block contains power IC, SMPS
transformer and several passive components.
The power IS STR-S5707 has power transistor. oscillator circuit, voltage comparator circuit, thermal protection
circuit, OCP(over current protection)circuit inside.
1. STR-S5707 BLOCK DIAGRAM
2. PIN DESCRIPTION
PIN NO
1
2
3
4
5
6
7
8
9
SYMBOL
C
GND
B
SINK
OCP
INH
F/B(SENS)
DRIVE
Vin
NAME
COLLECTOR
GROUND
BASE
SINK
OVER CURRENT PROTECTION
INHIBIT/LATCH
FEED BACK(SENSING)INPUT
DRIVE
Vin
3. OTHER FUNCTION
Symbol
OVP
TSD
Function
Built-in Overvoltage Protection Circuit
Built-in Thermal Shutdown Circuit
14
FUNCTION
POWER TRANSISTOR COLLECTOR
GROUND(POWER TRANSISTOR EMITTER)
POWER TRANSISTOR BASE
BASE URRENT(Is) INPUT
OVERCURRENT SENSING SIGNAL INPUT
SYNC, OFF TIME/LATCH CIRCUIT CONTROL INPUT
CONSTANT VOLTAGE CONTROL SIGNAL INPUT
BASE DRIVE CURRENT(Id)OUTPUT
SUPPLY VOLTAGE FOR CONTROL CIRCUIT
4. EXPLANATION OF CIRCUIT OPERATION
1) VIN terminal, start-up circuit
A Start-up circuit is to start and stop a operation of a control IC by detecting a voltage appearing at a VIN terminal(pin9).At start up of a power supply, when a voltage at the VIN terminal reaches to 8V by charging up C809 by the function
of a start-up resistor, Rs, a control circuit starts operating by the function of the start-up circuit. As shown in Fig. 2, since
a circuit current is suppressed 200 maximum (at VIN = 7.5V) until the control circuit starts its operation.
After the control circuit starts its operation, power source is obtained by smoothing voltage appearing at L1 winding.
Once the control circuit starts operating, as its voltage doesn’t reach the fixed voltage at once, VIN terminal voltage
starts dropping. However, as a shut-down voltage is set low(at 4.9V), while VIN terminal voltage reaches a shutdown
voltage, L1 winding voltage reaches the fixed voltage earlier so that the control circuit can continue on operating.
2) Oscillator, F/B terminal voltage (Pin #7)
A oscillator generates pulse signals which turns a power transistor on and off by making use of charge and discharge of
C1 and C2 incorporated in the Hybrid IC.
Constant voltage control of a switch-mode power supply is performed by changing both ON-time and OFF-time except
when the load is light (ex. remote control stand-by mode of TVs).
Fig. 4 shows how the oscillator works when the Hybrid IC independently operates (with no F/B nor INH signals). When
the power thransistor is on, C2 Is charged to the set voltage (approx 2.3V at Ta = 25 ). On the other hand, C1 starts
charging up through R1 from almost OV and the voltage across C1 reaches approx. 0.75V (Tc = 25 ). the output from
the oscillator is reversed and the power transistor turns off. At the same time C1 is quickly discharged by the function of
a internal circuit of the oscillator and the voltage across it decreases to almost OV. When the power transistor turns off,
C2 starts discharging through R2 and the voltage across C2 decreases with the inclination determined by the product of
C2 decreases to about 1V. the output from the oscillator is reversed again and the transistor consequently turns on. The
power transistor continues turning on and off by repeating the above-mentioned operations.
15
As the circuit in Fig. 3 shows, the ON-time is controlled by changing a current charged by C1, which is as the result of
that the detection winding (L1), which detects a change of voltage in a secondary side, connected to the sensing
terminal (Pin No. 7) has the current in accordance with an output signal from an output voltage detection circuit (an error
amplifier) built in. As an AC input voltage to the power supply gets the higher and a load current the smaller, the current
flowing to the SENS terminal gets the larger, and the ON-time gets the shorter.
3) Function of INH terminal (Pin #6), control OFF-time
Signal to the INH terminal is used as inputs to COMP.1 and COMP.2 inside of the control IC.A threshold voltage of
COMP.1 VTH1 is set at 0.75V (Ta = 25 ) and an input signal to a drive circuit becomes almost OV (the power transistor
is in OFF mode) when a voltage at the INH terminal reaches the VTH1. As long as the INH terminal voltage does not get
lower than VTH1. the power transistor sustains OFF mode. On the other hand, a threshold voltage of COMP.2 VTH2, is
set at 1.5V (Ta = 25 ). When the INH terminal voltage reaches VTH2, an output from COMP.2 reverses and, as a
result, C2, the OFF-tim of the oscillator which has been determined by the product of C2 and R2 ( 55 sec) can be
quicker up to approx. 2 sec. As long as the INH terminal voltage does not get lower than VTH2, A Voltage across C2
stays at almost 0V and a output from the oscillator keeps the power transistor being on. The relation between the INH
terminal voltage and the function of the oscillator described above is shown in Fig. 6 and FIg. 7
16
4) Quasi-resonant operation
By inputting a voltage signal which is synchronized with the energy discharge time of a secondary winding of a
transformer to the. INH terminal, quasi-resonant operation can be achieved. As shown in Fig. 8, the voltage of L1
winding which is synchronized. with the energy discharge time of a secondary winding. S1. shall be input to the INH
terminal through D804 and R809. Since VTH2 is set at 1.5V typical, a voltage at the INH terminal. VINH, shall be set at
Fig. 9 shows waveforms of VCE, Ic and VINH of the transistor, voltage across C807 in the oscillator as well as an output
from the oscillator when operating in quasi-resonant mode.
when the power transistor turns off and a voltage than VTH2 is applied to the INH terminal, C807 immediately discharges
and then starts charging again. Even after the discharge of energy of a secondary winding is completed, VINH does not
immediately increases. When it gets lower than VTH2 after the time,tr, which is determined by the production of internal
impedance of the IC and CINH, has past, the transistor turns on.
17
5) Drive circuit
The STR-S5707 applies the proportional drive system in order to minimize turn-on and saturation loss, and storage
time. In the conventional RCC system, turn-on loss and switching noise due to the surge current appearing when the
power transistor turns on are high as because the transistor is driven by the drive current shown in FIg. 10-1. In
addition, since is decreases linearly when the transistor turn off and a peak value of lB2 is not large, the storage time is
long and the VCE(SAT) voltage is high, which results in large turn-off loss. The circuit and the waveforms of the proportional
drive system which is applied to the STR-S5707 in order to reduce these switching loss and shorten the storage time
are shown in Fig. 10-2 respectively.
18
6) OCP (overcurrent protection)function
Overcurrent protection is performed pulse by directly detecting collector current of the power transistor.
Configuration of the OCP circuit is shown in. Detecting voltage is set to-1V below a reference point of GND (ground). In
addition, since the detecting voltage is set by a comparator, very stable characteristics against temperature is achieved
and drift of the deteting voltage against temperature change is almost OV.
7) Latch circuit
It is a circuit which sustains an output from the oscillator low and stops operation of the power supply when overvoltage
protection (OVP) circuit and thermal shutdown (TSD) circuit are in operation. As the sustaining current of the latch
circuit is 500 maximum when VIN terminal voltage is 4V. the power supply circuit sustains the off state as long as
current of 500 maximum flows to VIN terminal from a start-up resistor. In order to prevent a malfunction to be caused
by a noise and so on, delay time is provided by C1 incorporated in the IC and, therefore, the latch circuit operates when
the OVP of TSD circuit is in operation, of an external signal input is provided. for about 10 sec or longer. In addition,
even after the latch circuit start operating, the constant voltage regulator (Reg) circuit is in operation and the circuit
current is at high level. As a result. VIN terminal voltage rapidly decreases. When VIN terminal voltage becomes lower
than the shutdown voltage, VIN(OFF), (4.9V typical), it starts in-creasing as the circuit current is below 500 . When it
reaches the ON-state voltage. VIN(ON), (8V typical), VIN terminal voltage starts decreasing because the circuit current
increases again.
19
when the latch circuit is on. VIN terminal voltage increases and decreases with-in the range from 4.9V typical to 8V
typical and is prevented from abnormally rising. Fig. 12 shows an example of VIN terminal voltage waveform.
Cancellation of the latch-is done by decreasing VIN terminal voltage below 3.3V. The power supply can be restarted
disconnecting an AC input to the power supply once.
8) Thermal shutdown, circuit
It is a circuit to trigger the latch circuit when the frame temperature of the IC exceeds 150 (typical). Although the
temperature is actually sensed at the control chip. lt works against overheating of the power transistor as the power
transistor and the control IC are mounted on the same lead frame.
9) Overvoltage protection circuit
lt is a circuit to trigger the latch circuit when Vin terminal voltage exceeds 11V (typical). Although it basically functions as
protection of Vin terminal against overvoltage, since Vin terminal is usually supplied from the drive winding of the
transformer and the voltage is proportional to the output voltage, it also functions against the overvoltage of secondary
output which causes when the control circuit opens or in some other events.
20
5. OCP (OVER CURRENT PROTECTION) CIRCUIT
This circuit is designed to protect the circuit from over current due to overload occurred at the rear of 123[V] line
1) CONFIGURATION OF OCP CIRCUIT
2) EXPLANATION OF THE OPERATION
There is very little voltage drop at R423 of 123[V] line.
In case that the overload occurs at the rear of 123[V] line, the increase of the voltage drop at R423 bring down the base
voltage of the Q407 os as to drive the Q407
Because of the overload at the rear of the R423, the voltage of the point decreases. And this makes Q407 turn on
so that a voltage is applied to the #31 of l701.
In case that OCP operates by the #31 of the l1701, the set is protected by power off (#42 of l1701 LOW).
21
TROUBLE SHOOTING CHART S
NO POWER (NO OUTPUT SECOND POWER)
L801
LINE
FIL TER
D801
+
T801
PBS208GU
SMPS
TRANS
CHECK
R801
R CEMENT
CHECK
F801
250V A
R802
CHECK
SUPPLY
VOLTAGE
I801
VIN 9
SENS 7
CHECK
FEED BACK
INPUT
COLEECTOR 1
DON'T OPERATE POWER ON
I1702
VDD 8
I701
CHECK
DC 5V
CHECK
DC 5V
CLK 6
3 M-CLK
DATA 5
CHECK
CLOCK
PULSE
ST-BY: OV
POER ON:
1 EE-CLK
4 M-DATA
10
CHECK
DATA
PULSE
ST-BY: 5V
POWER ON
X701
CHECK
DC 5V
11
12 VDD
16 RESET
42 POWER
I501
H. VCC 21
BUS 43
INTERFACE 44
CHECK
H-OUT
PUSLE
CHECK
VOLT.
RC401
H. OUT 23
ST-BY: OV
POWER ON:
22
ST-BY: L
POWER ON: H
T401
NO PICTURE
OK
CHECK THE WAVE FORM OF
U101 #IF
GOTO A
NO
GOTO B
A
CHECK
VIDEO SIGNAL
I501
RC539
Z502
4.6V
2.6V
L505
47 INTERNAL
VIDEO INPUT
42 SELECT
VIDEO OUTPUT
32 ABL
2Vp-p
BRIGHT
CONTRAST
CHECK
HEATER
VTG 6.3Vms
45 VIDEO OUTPUT
4
33 ACL
T 402
CHECK
7.4V LINE
30 R OUTPUT
29 G OUTPUT
28 B OUTPUT
HEATER
D405
180 V
D402
ABL
CHECK
180V
LINE
RC549
CHECK
R/G/B SIGNAL
4.6V
1.6V
CC511
0.1MF
3Vp-p
B
I702
I501
SF 501
SAW FILTER
11
10
5 DATA
6 RF AGC
OUTPUT
6 CLK
CHECK
RF AGC OUTPUT
VTG
DC 5V - 8V
CHECK
CLK, EN, DATA
SIGNAL
U101
CHECK
DC 5V, 9V
33V LINE
I701
IF
AGC
5V
CL
9V
DA
33V
EN
5 T-CLK
6 T-DATA
7 M-EN
23
NO SOUND
MONO MODEL
GOTO C
STEREO MODEL
GOTO D
C
I501
Z503
Z502
CHECK
AUDIO
OUTPUT
SIGNAL
RC539
L505
45 VIDEO OUTPUT
47 INTERNAL
VIDEO INPUT
I602
49 SOUND IF
INPUT
8 -A-OUT
6 +A-OUT
2
3 A-IN
CHECK
AUDIO
INPUT
SIGNAL
CHECK
SOUND B+
DC 12V
51 AUDIO OUTPUT
D
I601
I501
Z2
CHECK
DC 9V
CHECK
RESONATOR
Z1
45 VIDEO OUTPUT
23
Z601
RC1
L1
47 INTERNAL
VIDEO INPUT
30 CES
1 OUT L
42 OUT R
24 COMP IN
CHECK
INPUT
COMP
SIGNAL
CHECK
SOUND IF
SIGNAL
49 SOUND IF
INPUT
7 AUDIO OUTPUT
CHECK
AUDIO
OUTPUT
SIGNAL
CHECK
SOUND B+
DC 12V
CHECK
R/L-INPUT
SIGNAL
I603
3
4 R-IN
2 L-IN
8 +R-OUT
11 -L-OUT
13 +L-OUT
24
CH DON'T STOP
GOOD
CHECK INPUT SIGNAL
CONDITIONS
GOTO E
BAD
E
LOSS OF SIGNL OR
WEEK SIGNAL
CHECK
VCO
COIL
I501
SF 501
SAW FILTER
11
2
10
3
I702
5 DATA
L501
6 CLK
6 RF AGC
OUTPUT
CHECK
RF AGC OUTPUT
VTC
DC 5V - 8V
CHECK
CLK, EN, DATA
SIGNAL
U101
CHECK
DC 5V, 9V
33V LINE
I701
IF
AGC
5V
CL
9V
DA
33V
EN
5 T-CLK
6 T-DATA
7 M-EN
NO COLOR
CHECK
VIDEO
SIGNAL
I501
40 COLOR
FILTER
CHECK
R/G/B
SIGNAL
42 SELECT
VIDEO OUTPUT
BRIGHT
32 ABL
CONTRAST
33 ACL
CHECK
7.4V LINE
4
30 R OUTPUT
29 G OUTPUT
28 B OUTPUT 15
4.6V
1.6V
3Vp-p
X501
25
CHECK
CRYSTAL
NO VERTICAL DEFLECTION
CHECK
V.OUT
SUGBAK
I301
INV 5
17 V.OUT
CHECK
SYNK
SIGNAL
V.D.Y
OUTPUT 2
CHECK
OUTPUT
37 SYNC
VCC 6
CHECK
DC 25V
26
ON SCREEN DISPLAY DOES NOT OPERATE
CHECK
FOR,60Hz
19
/ VS
20
/ HS
R
21
IC701
10
22
G
23
24
11
B
BL
IF OSD DOES NOT
OPERATE, CHANGE
IC701
CHECK
FOR, 15, 734Hz
OSC CHECK
REMOTE CONTROL DOES NOT OPERATE
lL701
REMOCON
SENSOR
GND 5V OUT
CHECK
WAVEFORM
IC701
34
27
R, G, B, BL
CHANGE
DESCRIPTION OF SEMICONDUCTORS
LA76070 (BUS CONTROL, VIF/SIF/Y/C/DEF)
I501 LA76070A
BUS CONTROL, VIF/SIF/Y/C/DEF
28
PIN ASSIGN OF IC LC864728V(I701)
OUTPUT
NOTE) XT is used 32.768 KHZ X-TAL
29
PIN ASSIGN OF IC TDA 7057Q (I603)
2 X 3 W sterei BTL audio output amplifier
PINNING
SYMBOL
SGND1
Vi(1)
Vp
Vi(p)
SGND2
n.c.
n.c.
OUT2+
PGND2
OUT2OUT1PGND1
OUT1+
PIN ASSIGN OF IC LA7841 (I301)
30
PIN
1
2
3
4
5
6
7
8
9
10
11
12
13
DESCRIPTION
signal ground 1
vollage input 1
positive supply voltage
voltage input 2
signal ground 2
not connected
not connected
positive output 2
power ground 2
negative output 2
negative output 1
power ground 1
positive output 1
PIN ASSIGN OF IC TDA 9852 (I601)
I2C-bus Controlled BTSC stereo/SAP decoder and audio processor
PINNING
SYMBOL
OUTL
LDL
VIL
EOL
CAV
VREF
LIL
AVL
SOL
LOL
CTW
CTS
CW
CS
VEO
VEI
CNR
CM
CDEC
GND
AGND
DGND
SDA
SCL
VCC
COMP
VCAP
CP1
CP2
CPH
CADJ
CER
CMO
CSS
LOR
SOR
AVR
LIR
CPS2
CPS1
EOR
VIR
LDR
OUTR
n.c
PINS
SDIP42
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
DESCRIPTION
QFP44
40
41
42
43
44
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
output, left channel
input loudness, left channel
input volume, left channel
output effects, left channel
automatic volume control capacitor
reference voltage 0.5Vcc
input line control, left channel
input automatic volume control, left channel
output selector, left channel
output line control, left channel
capacitor timing wideband for dbx
capacitor timing spectral for dbx
capacitor wideband for dbx
capacitor spectral for dbx
variable emphasis output for dbx
variable emphasis input for dbx
capacitor noise reduction for dbx
capacitor mute for SAP
capacitor DC-decoupling for SAP
ground
analog ground
digital ground
serial data input/output(l2C-bus)
serial clock input(l2C-bus)
supply voltage
composite input signal
capacitor for electronic filtering of supply
capacitor for pilot detector
capacitor for pilot detector
capacitor for phase detector
capacitor for filter adjustment
ceramic resonator
capacitor DC-decoupling mono
capacitor DC-decoupling stereo/SAP
output line control, right channel
output selector, right channel
input automatic volume control, right channel
input line control, right channel
capacitor 2 pseudo function
capacitor 1 pseudo function
output effects, right channel
input volume, right channel
input loudness, right channel
output,right channel
not connected
31
PARTS LIST
(DTQ-21T1FS)
Loc
ZZ100
ZZ110
30
40
50
60
10000
M821
ZZ120
M211
M541
M591
M781
ZZ130
10
20
M641
M801
M811
M821
ZZ131
ZZ132
ZZ140
M191
M201A
M201B
M201C
M211A
M211B
M481
M481A
M561
M681
M781
SP01A
SP02A
V901
ZZ200
M201
ZZ202
PA601
PA602
SP01
SP02
A001
C101
C102
C103
C104
C301
C302
C303
Item Code
Item Name
Description
48B3225C04
PTACPWJ591
486A716200
4859000240
4850A00650
4850A02510
48586054K1
4858213800
PTBCSHJ596
4852147001
4855415800
4855930923
4857817612
PTPKCPJ596
6520010100
6520010200
6520010100
485804763B
4858179000
4858261100
58G0000110
48519A5210
PTCACAJ596
4851926801
4856013301
4856214902
4856013303
7122401412
7122401412
4854848001
4856716000
48556159SS
4856812001
4857821204
7128301011
7128301011
4859608761
PTFMSJJ596
4852060402
PTSPPWJ591
4850703S51
4850703S53
4858306810
4858306810
4859812792
CEXF1H229V
CEXF1C471V
CEXF1E470V
CEXF1H109V
CMXB1H103J
CEXF1H479V
CEXF1H100V
TRANSMITTER REMOCON
ACCESSORY AS
BATTERY
ADAPTER
TRANS ANT MATCHING
ANT ROD
MANUAL INSTRUCTION
BAG INSTRUCTION
COVER BACK AS
COVER BACK
SPEC PLATE
DECO TERM
CLOTH BLACK
PACKING AS
STAPLE PIN
STAPLE PIN
STAPLE PIN
BOX CARTON
PAD
BAG P.E
COIL DEGAUSSING
CRT GROUND AS
CABINET AS
BUTTON CTRL AS
SCREW CRT FIXING AS
WASHER RUBBER
SCREW CRT FIXING AS
SCREW TAPPING
SCREW TAPPING
BUTTON POWER
SPRING
MARK BRAND
TIE CABLE
CLOTH BLACK
SCREW TAPPING
SCREW TAPPING
CRT
MASK FRONT AS
MASK FRONT
SPEAKER AS
CONN AS
CONN AS
SPEAKER
SPEAKER
PCB MAIN
C ELECTRO
C ELECTRO
C ELECTRO
C ELECTRO
C MYLAR
C ELECTRO
C ELECTRO
R-25C04
DTQ-20T1FS
AAA
2P15A 300V(D=4.0)
IMT-060 (CAPRISTOR OUT) B
S3BW216B (L=600 MM)
DTM-2082CW
L.D.P.E T0.05X250X400
DTQ-21T1FS
HIPS BK
150ART P/E FILM (C/TV)
PVC T0.2
FELT T0.7 L=250
DTQ-21T1FS
18M/M J D O
#3417
18M/M J D O
DW-3A
EPS 21T1
LDPE T0.02X1200X1000000
DC-2080
2101H-1015-1P
DTQ-21T1FS
4932801+5530201
30X140 YL
CR T2.0
30X250 YL
T2S TRS 4X14 MFZN BK
T2S TRS 4X14 MFZN BK
ABS BK
SWPA PIE0.5
SILVER ETCHING DIA-CUTTIN
NYLON66 DA100
FELT 220X12XT2
T2S WAS 3X10 MFZN
T2S WAS 3X10 MFZN
A51JSW41X01 P00
DTQ-21T1FS
HIPS BK
DTQ-20T1FS
YH025-03+35098+ULW=300
YH025-03+35098+ULW=500
3W 16 OHM F2035C03-3
3W 16 OHM F2035C03-3
246X330 S1B
50V RSS 2.2MF (5X11) TP
16V RSS 470MF (10X12.5)TP
25V RSS 47MF (5X11) TP
50V RSS 1MF (5X11) TP
50V EU 0.01MF J (TP)
50V RSS 4.7MF (5X11) TP
50V RSS 10MF (5X11) TP
51
PARTS LIST
(DTQ-21T1FS)
Loc
C304
C305
C307
C308
C309
C310
C311
C401
C402
C403
C404
C405
C406
C407
C408
C409
C410
C411
C412
C413
C414
C415
C416
C417
C420
C421
C444
C501
C503
C507
C508
C510
C511
C513
C514
C515
C517
C518
C519
C520
C522
C524
C531
C532
C533
C537
C542
C543
C544
Item Code
Item Name
Description
CEXF1V471V
CEXF1H101V
CXSL2H100D
CMXL1J104J
CEXF1H100V
CEXF1E102V
CEXD1H229Q
CCXB2H222K
CEXF1H220V
CCYB3A103K
CMYH3C722J
CEXF2C109V
CMYE2D474J
CEXF2E100V
CEXF1H100V
CCXB2H102K
CEXF1C222V
CCXB2H102K
CMXB1H104J
CEXF1C471V
CEXF1C471V
CCXB2H102K
CEXF1E101V
CEXF2C101V
CCXB2H271K
CEXF1H479V
CCXB3D271K
CEXF1H100V
CEXF1C102V
CEXF1H100V
CMXB1H473J
CEXF1H109V
CMXB1H333J
CEXF1H108V
CEXF1H108V
CEXF1H108V
CEXF1E101V
CEXF1H109V
CMXB1H333J
CMXM2A102J
CEXF1H339V
CEXF1C102V
CEXF1H109V
CEXF1H109V
CEXF1H229V
CEXF1H100V
CEXF1H478V
CEXF1H109V
CEXF1H229V
C ELECTRO
C ELECTRO
C CERA
C MYLAR
C ELECTRO
C ELECTRO
C ELECTRO
C CERA
C ELECTRO
C CERA
C MYLAR
C ELECTRO
C MYLAR
C ELECTRO
C ELECTRO
C CERA
C ELECTRO
C CERA
C MYLAR
C ELECTRO
C ELECTRO
C CERA
C ELECTRO
C ELECTRO
C CERA
C ELECTRO
C CERA
C ELECTRO
C ELECTRO
C ELECTRO
C MYLAR
C ELECTRO
C MYLAR
C ELECTRO
C ELECTRO
C ELECTRO
C ELECTRO
C ELECTRO
C MYLAR
C MYLAR
C ELECTRO
C ELECTRO
C ELECTRO
C ELECTRO
C ELECTRO
C ELECTRO
C ELECTRO
C ELECTRO
C ELECTRO
35V RSS 470MF (10X20) TP
50V RSS 100MF (8X11.5) TP
500V SL 10PF D (TAPPING)
63V MEU 0.1MF J
50V RSS 10MF (5X11) TP
25V RSS 1000MF (13X20) TP
50V RT 2.2MF (6.3X11) TP
500V B 2200PF K (TAPPING)
50V RSS 22MF (5X11) TP
1KV B 0.01MF K
1.6KV BUP 7200PF J
160V RSS 1MF (6.3X11) TP
200V PU 0.47MF J
250V RSS 10MF (10X20) TP
50V RSS 10MF (5X11) TP
500V B 1000PF K (TAPPING)
16V RSS 2200MF (13X25) TP
500V B 1000PF K (TAPPING)
50V EU 0.1MF J (TP)
16V RSS 470MF (10X12.5)TP
16V RSS 470MF (10X12.5)TP
500V B 1000PF K (TAPPING)
25V RSS 100MF (6.3X11) TP
160V RSS 100MF (16X25) TP
500V B 270PF K (TAPPING)
50V RSS 4.7MF (5X11) TP
2KV B 270PF K (T)
50V RSS 10MF (5X11) TP
16V RSS 1000MF (10X20) TP
50V RSS 10MF (5X11) TP
50V 0.047MF J (TP)
50V RSS 1MF (5X11) TP
50V EU 0.033MF J (TP)
50V RSS 0.1MF (5X11) TP
50V RSS 0.1MF (5X11) TP
50V RSS 0.1MF (5X11) TP
25V RSS 100MF (6.3X11) TP
50V RSS 1MF (5X11) TP
50V EU 0.033MF J (TP)
100V 1000PF J (TP)
50V RSS 3.3MF (5X11) TP
16V RSS 1000MF (10X20) TP
50V RSS 1MF (5X11) TP
50V RSS 1MF (5X11) TP
50V RSS 2.2MF (5X11) TP
50V RSS 10MF (5X11) TP
50V RSS 0.47MF (5X11) TP
50V RSS 1MF (5X11) TP
50V RSS 2.2MF (5X11) TP
52
PARTS LIST
(DTQ-21T1FS)
Loc
C601
C602
C603
C605
C606
C607
C608
C609
C610
C611
C612
C613
C614
C615
C616
C618
C619
C620
C621
C622
C623
C624
C625
C626
C627
C628
C629
C630
C632
C633
C634
C636
C637
C640
C641
C704
C706
C708
C709
C711
C801
C802
C803
C804
C805
C806
C807
C808
C809
Item Code
Item Name
Description
CEXF1H470V
CEXF1H470V
CMXL1J154J
CEXF1H229V
CEXF1H478V
CEXF1E101V
CEXF1H229V
CEXF1H100V
CEXF1H100V
CEXF1H109V
CEXF1H109V
CMXL1J473J
CEXF1H100V
CMXL1J104J
CEXF1H479V
CEXF1E101V
CEXF1H100V
CEXF1E101V
CMXL1J474J
CMXL1J224J
CEXF1H479V
CEXF1H100V
CEXF1H479V
CEXF1H479V
CEXF1H229V
CMXB1H153J
CMXB1H153J
CEXF1H229V
CMXL1J154J
CMXL1J334J
CMXL1J334J
CEXF1E471V
CMXL1J104J
CMXB1H223J
CMXB1H223J
CEXF1E101V
CEXF1H100V
CEXF1H229V
CEXF1H109V
CEXF1H100V
CL1UC3104M
CCXF3A472Z
CCXF3A472Z
CEYN2G221P
CH1BFE222M
CBYB3D152K
CCXB2H102K
CEXF2A100V
CEXF1E331V
C ELECTRO
C ELECTRO
C MYLAR
C ELECTRO
C ELECTRO
C ELECTRO
C ELECTRO
C ELECTRO
C ELECTRO
C ELECTRO
C ELECTRO
C MYLAR
C ELECTRO
C MYLAR
C ELECTRO
C ELECTRO
C ELECTRO
C ELECTRO
C MYLAR
C MYLAR
C ELECTRO
C ELECTRO
C ELECTRO
C ELECTRO
C ELECTRO
C MYLAR
C MYLAR
C ELECTRO
C MYLAR
C MYLAR
C MYLAR
C ELECTRO
C MYLAR
C MYLAR
C MYLAR
C ELECTRO
C ELECTRO
C ELECTRO
C ELECTRO
C ELECTRO
C LINE ACROSS
C CERA
C CERA
C ELECTRO
C CERA AC
C CERA
C CERA
C ELECTRO
C ELECTRO
50V RSS 47MF (6.3X11) TP
50V RSS 47MF (6.3X11) TP
63V MEU 0.15MF J
50V RSS 2.2MF (5X11) TP
50V RSS 0.47MF (5X11) TP
25V RSS 100MF (6.3X11) TP
50V RSS 2.2MF (5X11) TP
50V RSS 10MF (5X11) TP
50V RSS 10MF (5X11) TP
50V RSS 1MF (5X11) TP
50V RSS 1MF (5X11) TP
63V MEU 0.047MF J
50V RSS 10MF (5X11) TP
63V MEU 0.1MF J
50V RSS 4.7MF (5X11) TP
25V RSS 100MF (6.3X11) TP
50V RSS 10MF (5X11) TP
25V RSS 100MF (6.3X11) TP
63V MEU 0.47MF J
63V MEU 0.22MF J (TP)
50V RSS 4.7MF (5X11) TP
50V RSS 10MF (5X11) TP
50V RSS 4.7MF (5X11) TP
50V RSS 4.7MF (5X11) TP
50V RSS 2.2MF (5X11) TP
50V EU 0.015MF J (TP)
50V EU 0.015MF J (TP)
50V RSS 2.2MF (5X11) TP
63V MEU 0.15MF J
63V MEU 0.33MF J (TP)
63V MEU 0.33MF J (TP)
25V RSS 470MF (10X16) TP
63V MEU 0.1MF J
50V EU 0.022MF J (TP)
50V EU 0.022MF J (TP)
25V RSS 100MF (6.3X11) TP
50V RSS 10MF (5X11) TP
50V RSS 2.2MF (5X11) TP
50V RSS 1MF (5X11) TP
50V RSS 10MF (5X11) TP
WORLD AC250V 0.1UF M R.47
1KV F 4700PF Z (T)
1KV F 4700PF Z (T)
400V LHS 220MF (35X30)
U/C/V AC400V 2200PF
2KV BL (N) 1500PF
500V B 1000PF K (TAPPING)
100V RSS 10MF (6.3X11) TP
25V RSS 330MF (10X12.5)TP
53
PARTS LIST
(DTQ-21T1FS)
Loc
C810
C811
C812
C813
C814
C815
C816
C817
C818
C819
C820
C888
C889
C901
C908
CA01
CA02
CAC01
CAC02
CC101
CC102
CC504
CC505
CC509
CC511
CC512
CC516
CC523
CC530
CC534
CC535
CC536
CC538
CC539
CC544
CC601
CC602
CC604
CC617
CC631
CC701
CC702
CC703
CC705
CC707
CC710
CC712
CC713
CC714
Item Code
Item Name
Description
CCXB3A471K
CCXB3A471K
CEXF1E221V
CCXB3D102K
CEYF2C101V
CCXB3A102K
CEXF1E102V
CCXB3A102K
CEXF1E471V
CEXF1E101V
CCXB3A102K
CH1BFE222M
CCXF3A472Z
CBXB3D102K
CEXF1H479V
CEXF1H229V
CEXF1H229V
HCBK104KCA
HCBK104KCA
HCQK101JCA
HCQK101JCA
HCBK103KCA
HCBK103KCA
HCBK102KCA
HCBK104KCA
HCQK160JCA
HCBK103KCA
HCBK103KCA
HCQK561JCA
HCQK470JCA
HCQK220JCA
HCBK103KCA
HCQK101JCA
HCQK101JCA
HCBK103KCA
HCQK101JCA
HCQK101JCA
HCBK822KCA
HCBK103KCA
HCBK822KCA
HCQK180JCA
HCQK180JCA
HCBK103KCA
HCBK103KCA
HCBK333KCA
HCQK221JCA
HCQK101JCA
HCQK101JCA
HCQK101JCA
C CERA
C CERA
C ELECTRO
C CERA
C ELECTRO
C CERA
C ELECTRO
C CERA
C ELECTRO
C ELECTRO
C CERA
C CERA AC
C CERA
C CERA
C ELECTRO
C ELECTRO
C ELECTRO
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
1KV B 470PF K (T)
1KV B 470PF K (T)
25V RSS 220MF (8X11.5) TP
2KV B 1000PF K (TAPPING)
160V RSS 100MF (16X25)
1KV B 1000PF K (TAPPING)
25V RSS 1000MF (13X20) TP
1KV B 1000PF K (TAPPING)
25V RSS 470MF (10X16) TP
25V RSS 100MF (6.3X11) TP
1KV B 1000PF K (TAPPING)
U/C/V AC400V 2200PF
1KV F 4700PF Z (T)
2KV BL(N) 1000PF K (T)
50V RSS 4.7MF (5X11) TP
50V RSS 2.2MF (5X11) TP
50V RSS 2.2MF (5X11) TP
50V X7R 0.1MF K 2012
50V X7R 0.1MF K 2012
50V CH 100PF J 2012
50V CH 100PF J 2012
50V X7R 0.01MF K 2012
50V X7R 0.01MF K 2012
50V X7R 1000PF K 2012
50V X7R 0.1MF K 2012
50V CH 16PF J 2012
50V X7R 0.01MF K 2012
50V X7R 0.01MF K 2012
50V CH 560PF J 2012
50V CH 47PF J 2012
50V CH 22PF J 2012
50V X7R 0.01MF K 2012
50V CH 100PF J 2012
50V CH 100PF J 2012
50V X7R 0.01MF K 2012
50V CH 100PF J 2012
50V CH 100PF J 2012
50V X7R 8200PF K 2012
50V X7R 0.01MF K 2012
50V X7R 8200PF K 2012
50V CH 18PF J 2012
50V CH 18PF J 2012
50V X7R 0.01MF K 2012
50V X7R 0.01MF K 2012
50V X7R 0.033MF K 2012
50V CH 220PF J 2012
50V CH 100PF J 2012
50V CH 100PF J 2012
50V CH 100PF J 2012
54
PARTS LIST
(DTQ-21T1FS)
Loc
CC715
CC716
CC717
CC718
CC722
Loc
CC726
CC902
CC903
CC904
CC908
D101
D102
D103
D104
D301
D401
D402
D403
D404
D405
D406
D407
D408
D409
D412
D501
D504
D601
D701
D703
D740
D741
D801
D802
D803
D804
D805
D806
D807
D808
D809
D810
D901
F801
F801A
F801B
I301
I301
I301A
Item Code
Item Name
Description
HCQK101JCA
HCBK104KCA
HCBK104KCA
HCBK104KCA
HCQK101JCA
Item Code
HCBK103KCA
HCQK271JCA
HCQK271JCA
HCQK271JCA
HCQK102JCA
DUZ9R1BM-DUZ5R1BM-DUZ33B---DUZ9R1BM-D1N4003--NBYD33GT-NBYD33GT-NBYD33GT-NBYD33GT-NBYD33GT-D1N4148--DUZ7R5BM-D1N4148--DUZ9R1BM-DBY228---DUZ9R1BM-D1N4148--DUZ8R2BM-DUZ3R9B--DKLR114L-D1N4148--DUZ5R1BM-DPBS208GUD1N4937GPD1N4937GPD1N4937GPD1N4937GPDPR3005G-DPR1505G-DPR1505G-DUZ6R2BM-D1N4148--85801065GY
5FKGB4022R
4857415001
4857415001
1LA7841--PTB2SW7101
4857027101
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
Item Name
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
DIODE ZENER
DIODE ZENER
DIODE ZENER
DIODE ZENER
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE ZENER
DIODE
DIODE ZENER
DIODE
DIODE ZENER
DIODE
DIODE ZENER
DIODE ZENER
LED
DIODE
DIODE ZENER
DIODE BRIDGE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE ZENER
DIODE
WIRE COPPER
FUSE GLASS TUBE
CLIP FUSE
CLIP FUSE
IC VERTICAL
HEAT SINK ASS`Y
HEAT SINK
50V CH 100PF J 2012
50V X7R 0.1MF K 2012
50V X7R 0.1MF K 2012
50V X7R 0.1MF K 2012
50V CH 100PF J 2012
Description
50V X7R 0.01MF K 2012
50V CH 270PF J 2012
50V CH 270PF J 2012
50V CH 270PF J 2012
50V CH 1000PF J 2012
UZ-9.1BM 9.1V
UZ-5.1BM
UZ-33B
UZ-9.1BM 9.1V
1N4003 (TAPPING)
BYD33G-T
BYD33G-T
BYD33G-T
BYD33G-T
BYD33G-T
1N4148 (TAPPING)
UZ-7.5BM 7.5V
1N4148 (TAPPING)
UZ-9.1BM 9.1V
BY228 (TAPPING)
UZ-9.1BM 9.1V
1N4148 (TAPPING)
UZ-8.2B (8.2V)
UZ-3.9B
KLR114L
1N4148 (TAPPING)
UZ-5.1BM
PBS208GU-CA
1N4937GP (TAPPING)
1N4937GP (TAPPING)
1N4937GP (TAPPING)
1N4937GP (TAPPING)
PR3005G
PR1505G
PR1505G
UZ-6.2BM 6.2V
1N4148 (TAPPING)
AWG22 1/0.65 TIN COATING
KS MF51 4A 250V NR
PFC5000-0702
PFC5000-0702
LA7841
1LA7841--- + 7174301011
SPCC T1.0+SN
55
PARTS LIST
(DTQ-21T1FS)
Loc
I301B
I501
I601
I603
I603
I603A
I603B
I701
I702
I801
I801
I801A
I801B
I802
IL701
J001
J002
J004
J005
J006
J007
J008
J009
J010
J011
J012
J013
J014
J015
J017
J019
J020
J021
J022
J023
J024
J025
J026
J027
J028
J029
J030
J031
J032
J033
J034
J035
J036
Item Code
Item Name
Description
7174301011
1LA76070A1TDA9852-1TDA7057QPTC2SW6109
4857026109
7174301011
1LC8645G79
124LC02B-1STRS5707PTA2SW6107
4857026107
7174301211
1LTV817C-1TFMW538085801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
SCREW TAPPTITE
IC VIDEO PROCESSOR
IC AUDIO PROCESSOR
IC AUDIO AMP
HEAT SINK ASS`Y
HEAT SINK
SCREW TAPPTITE
IC MICOM
IC MEMORY
IC POWER
HEAT SINK ASS`Y
HEAT SINK
SCREW TAPPTITE
IC PHOTO COUPLER
IC PREAMP
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
TT2 RND 3X10 MFZN
LA76070A
TDA9852
TDA7057Q
1TDA7057Q- + 7174301011
AL EX
TT2 RND 3X10 MFZN
LC864728V-5G79
24LC02B
STR-S5707
1STRS5707- + 7174301211
AL EX
TT2 RND 3X12 MFZN
LTV-817C
TFMW5380
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
56
PARTS LIST
(DTQ-21T1FS)
Loc
J037
J038
J040
J041
J042
J043
J044
J045
J046
J047
J049
J050
J051
J052
J053
J055
J058
J060
J101
J102
J103
J301
J302
J303
J305
J306
J310
J402
J403
J404
J405
J408
J409
J410
J411
J501
J502
J503
J504
J505
J506
J507
J509
J601
J602
J603
J604
J605
J606
Item Code
Item Name
Description
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
57
PARTS LIST
(DTQ-21T1FS)
Loc
J607
J608
J609
J610
J615
J701
J702
J703
J704
J705
J706
J740
J741
J801
J802
J803
J808
J810
J813
J901
J902
JA01
JA02
JA03
JAC03
JC101
JC302
JC303
JC402
JC501
JC503
JC504
JC601
JC602
JC701
JC702
JC703
JC704
JC706
JC707
JC740
JC801
JC901
JC902
JC903
JC904
L401
L402
L403
Item Code
Item Name
Description
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
85801065GY
4859108450
4859102130
4859109250
HRFT000-CA
HRFT000-CA
HRFT000-CA
HRFT000-CA
HRFT000-CA
HRFT000-CA
HRFT000-CA
HRFT000-CA
HRFT000-CA
HRFT000-CA
HRFT000-CA
HRFT000-CA
HRFT000-CA
HRFT000-CA
HRFT000-CA
HRFT000-CA
HRFT000-CA
HRFT000-CA
HRFT000-CA
HRFT000-CA
HRFT000-CA
HRFT000-CA
58H0000020
58W0000007
5CPZ150K02
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
WIRE COPPER
JACK PIN BOARD
JACK EARPHONE
JACK PIN BOARD
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
COIL H-LINEARITY
COIL WIDTH
COIL PEAKING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
AWG22 1/0.65 TIN COATING
YSC03P-4120-14A
YSC-1537
PH-JB-9614A
1/10 0 OHM 2012
1/10 0 OHM 2012
1/10 0 OHM 2012
1/10 0 OHM 2012
1/10 0 OHM 2012
1/10 0 OHM 2012
1/10 0 OHM 2012
1/10 0 OHM 2012
1/10 0 OHM 2012
1/10 0 OHM 2012
1/10 0 OHM 2012
1/10 0 OHM 2012
1/10 0 OHM 2012
1/10 0 OHM 2012
1/10 0 OHM 2012
1/10 0 OHM 2012
1/10 0 OHM 2012
1/10 0 OHM 2012
1/10 0 OHM 2012
1/10 0 OHM 2012
1/10 0 OHM 2012
1/10 0 OHM 2012
L-76(76.5UH)
TRW-414M
15UH K (AXIAL 3.5MM)
58
PARTS LIST
(DTQ-21T1FS)
Loc
L501
L502
L503
L504
L505
L507
L601
L602
L604
L701
L801
L802
L804
L805
L806
L807
L901
M352
P102
P103
P401
P601
P602
P802A
P802B
P803
P804
P901
PA501
PWC1
Q401
Q402
Q403
Q404
Q406
Q407
Q801
Q802
Q803
Q901
Q902
Q903
QC401
QC405
QC501
QC601
QC603
QC604
QC701
QC702
Item Code
Item Name
Description
58N0000037
5CPZ150K02
58C5580019
5CPZ150K02
5CPZ150K02
58S0000045
5MC0000100
5MC0000100
5CPZ560K03
5CPZ150K02
5PLF20A1-5MC0000100
58C0000107
5MC0000100
5MC0000100
5MC0000100
5CPX820J-4853530901
485923162S
485923522S
4859240120
485923162S
485923162S
4859901111
4859203030
4857417500
4857417500
4857417500
4850708N08
4859900910
TKTC3207-TKTC3198YT2SD2499-TKTC3205YTKTC3205YTKSA1013YTKTC3207-TKTC3198YTKTC3198YTKTC3207-TKTC3207-TKTC3207-T2SC2412KB
T2SC2412KB
T2SA1037KB
T2SC2412KB
T2SC2412KB
T2SC2412KB
T2SA1037KB
T2SC2412KB
COIL VCO
COIL PEAKING
COIL CHOKE
COIL PEAKING
COIL PEAKING
COIL SIF
COIL BEAD
COIL BEAD
COIL PEAKING
COIL PEAKING
FILTER LINE
COIL BEAD
COIL CHOKE
COIL BEAD
COIL BEAD
COIL BEAD
COIL PEAKING
HOLDER LED
CONN WAFER
CONN WAFER
CONN WAFER
CONN WAFER
CONN WAFER
CORD POWER
CONN TERMINAL
TERM PIN
TERM PIN
TERM PIN
CONN AS
CORD POWER AS
TR
TR
TR
TR
TR
TR
TR
TR
TR
TR
TR
TR
TR CHIP
TR CHIP
TR CHIP
TR CHIP
TR CHIP
TR CHIP
TR CHIP
TR CHIP
TRF-V004
15UH K (AXIAL 3.5MM)
TRF-9225 (0.55UH)
15UH K (AXIAL 3.5MM)
15UH K (AXIAL 3.5MM)
TRF-S001
HC-3550
HC-3550
56UH K (AXIAL 7MM)
15UH K (AXIAL 3.5MM)
LF-20A1
HC-3550
L-680
HC-3550
HC-3550
HC-3550
82UH J (RADIAL)
P.P
YW025-03 (STICK)
YW025-09 (STICK)
YFW500-06
YW025-03 (STICK)
YW025-03 (STICK)
KKP-419C KLCE-2F (2.1ME)
YPT-018
DA-IB0214(D2.3/DY PIN)
DA-IB0214(D2.3/DY PIN)
DA-IB0214(D2.3/DY PIN)
BIC-08T-25T+C-20T+ULW=400
KKP-419C+YPT-018=2100
KTC3207 (TP)
KTC3198Y
2SD2499
KTC3205Y (TP)
KTC3205Y (TP)
KSA1013Y (TP)
KTC3207 (TP)
KTC3198Y
KTC3198Y
KTC3207 (TP)
KTC3207 (TP)
KTC3207 (TP)
2SC2412K-T146-BR
2SC2412K-T146-BR
2SA1037K-T146-R
2SC2412K-T146-BR
2SC2412K-T146-BR
2SC2412K-T146-BR
2SA1037K-T146-R
2SC2412K-T146-BR
59
PARTS LIST
(DTQ-21T1FS)
Loc
QC703
QC704
QC901
R102
R103
R104
R305
R306
R307
R313
R403
R405
R406
R407
R408
R409
R410
R411
R413
R414
R416
R417
R419
R420
R423
R424
R425
R426
R601
R602
R801
R802
R803
R804
R805
R806
R807
R808
R809
R810
R812
R813
R814
R816
R818
R820
R821
R822
R901
Item Code
Item Name
Description
T2SC2412KB
T2SC2412KB
T2SA1037KB
RS02Z220JS
RD-2Z820JRS01Z273JRS01Z331JRS01Z471JRS01Z471JRS01Z209JRD-2Z272JRS02Z113JS
RS02Z113JS
RS01Z272JRS01Z562JRS01Z339JRS01Z369JRD-4Z123JRS02Z229JS
RS01Z229JRS01Z100JRD-4Z131JRD-4Z131JRS01Z100JRF01Z688JRD-4Z153JRD-4Z223JRD-4Z153JRD-2Z121JRD-2Z121JRX10B339JN
RS02Z363JS
DJ140M290L
RC-2Z565JRF02Z228JRD-4Z102JRD-4Z330JRD-4Z104JRD-4Z182JRS01Z180JRD-4Z331JRD-4Z621JRD-2Z620JRD-4Z222JRD-4Z432JRD-4Z101JRD-4Z472JRD-4Z153JRD-4Z474J-
TR CHIP
TR CHIP
TR CHIP
R M-OXIDE FILM
R CARBON FILM
R M-OXIDE FILM
R M-OXIDE FILM
R M-OXIDE FILM
R M-OXIDE FILM
R M-OXIDE FILM
R CARBON FILM
R M-OXIDE FILM
R M-OXIDE FILM
R M-OXIDE FILM
R M-OXIDE FILM
R M-OXIDE FILM
R M-OXIDE FILM
R CARBON FILM
R M-OXIDE FILM
R M-OXIDE FILM
R M-OXIDE FILM
R CARBON FILM
R CARBON FILM
R M-OXIDE FILM
R FUSIBLE
R CARBON FILM
R CARBON FILM
R CARBON FILM
R CARBON FILM
R CARBON FILM
R CEMENT
R M-OXIDE FILM
POSISTOR
R CARBON COMP
R FUSIBLE
R CARBON FILM
R CARBON FILM
R CARBON FILM
R CARBON FILM
R M-OXIDE FILM
R CARBON FILM
R CARBON FILM
R CARBON FILM
R CARBON FILM
R CARBON FILM
R CARBON FILM
R CARBON FILM
R CARBON FILM
R CARBON FILM
2SC2412K-T146-BR
2SC2412K-T146-BR
2SA1037K-T146-R
2W 22 0HM J SMALL
1/2 82 OHM J
1W 27K OHM J (TAPPING)
1W 330 OHM J (TAPPING)
1W 470 OHM J (TAPPING)
1W 470 OHM J (TAPPING)
1W 2 OHM J
1/2 2.7K OHM J
2W 11K OHM J SMALL
2W 11K OHM J SMALL
1W 2.7K OHM J (TAPPING)
1W 5.6K OHM J (TAPPING)
1W 3.3 OHM J (TAPPING)
1W 3.6 OHM J (TAPPING)
1/4 12K OHM J
2W 2.2 OHM J SMALL
1W 2.2 OHM J (TAPPING)
1W 10 OHM J (TAPPING)
1/4 130 OHM J
1/4 130 OHM J
1W 10 OHM J (TAPPING)
1W 0.68 OHM J (TAPPING)
1/4 15K OHM J
1/4 22K OHM J
1/4 15K OHM J
1/2 120 OHM J
1/2 120 OHM J
10W 3.3 OHM J BENCH 4P
2W 36K OHM J SMALL
J503P53D140M290L
1/2 5.6M OHM J
2W 0.22 OHM J (TAPPING)
1/4 1K OHM J
1/4 33 OHM J
1/4 100K OHM J
1/4 1.8K OHM J
1W 18 OHM J (TAPPING)
1/4 330 OHM J
1/4 620 OHM J
1/2 62 OHM J
1/4 2.2K OHM J
1/4 4.3K OHM J
1/4 100 OHM J
1/4 4.7K OHM J
1/4 15K OHM J
1/4 470K OHM J
60
PARTS LIST
(DTQ-21T1FS)
Loc
R905
R906
R907
R908
R909
R910
RAC01
RAC02
RAC03
RAC04
RAC05
RAC06
RC101
RC102
RC103
RC104
RC301
RC302
RC303
RC308
RC309
RC310
RC311
RC312
RC401
RC402
RC404
RC412
RC419
RC420
RC421
RC422
RC501
RC502
RC503
RC504
RC505
RC506
RC507
RC508
RC509
RC510
RC511
RC512
RC513
RC514
RC515
RC516
RC517
Item Code
Item Name
Description
RS02Z123JS
RS02Z123JS
RS02Z123JS
RD-2Z332JRD-2Z332JRD-2Z332JHRFT750JCA
HRFT101JCA
HRFT391JCA
HRFT104JCA
HRFT391JCA
HRFT104JCA
HRFT184JCA
HRFT102JCA
HRFT102JCA
HRFT102JCA
HRFT472JCA
HRFT104JCA
HRFT153JCA
HRFT151JCA
HRFT912JCA
HRFT333JCA
HRFT101JCA
HRFT133JCA
HRFT331JCA
HRFT102JCA
HRFT103JCA
HRFT103JCA
HRFT121JCA
HRFT103JCA
HRFT121JCA
HRFT103JCA
HRFT133JCA
HRFT202JCA
HRFT124JCA
HRFT393JCA
HRFT823JCA
HRFT272JCA
HRFT622JCA
HRFT824JCA
HRFT750JCA
HRFT182JCA
HRFT750JCA
HRFT222JCA
HRFT332JCA
HRFT331JCA
HRFT331JCA
HRFT331JCA
HRFT304JCA
R M-OXIDE FILM
R M-OXIDE FILM
R M-OXIDE FILM
R CARBON FILM
R CARBON FILM
R CARBON FILM
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
2W 12K 0HM J SMALL
2W 12K 0HM J SMALL
2W 12K 0HM J SMALL
1/2 3.3K OHM J
1/2 3.3K OHM J
1/2 3.3K OHM J
1/10 75 OHM J 2012
1/10 100 OHM J 2012
1/10 390 OHM J 2012
1/10 100K OHM J 2012
1/10 390 OHM J 2012
1/10 100K OHM J 2012
1/10 180K OHM J 2012
1/10 1K OHM J 2012
1/10 1K OHM J 2012
1/10 1K OHM J 2012
1/10 4.7K OHM J 2012
1/10 100K OHM J 2012
1/10 15K OHM J 2012
1/10 150 OHM J 2012
1/10 9.1K OHM J 2012
1/10 33K OHM J 2012
1/10 100 OHM J 2012
1/10 13K OHM J 2012
1/10 330 OHM J 2012
1/10 1K OHM J 2012
1/10 10K OHM J 2012
1/10 10K OHM J 2012
1/10 120 OHM J 2012
1/10 10K OHM J 2012
1/10 120 OHM J 2012
1/10 10K OHM J 2012
1/10 13K OHM J 2012
1/10 2K OHM J 2012
1/10 120K OHM J 2012
1/10 39K OHM J 2012
1/10 82K OHM J 2012
1/10 2.7K OHM J 2012
1/10 6.2K OHM J 2012
1/10 820K OHM J 2012
1/10 75 OHM J 2012
1/10 1.8K OHM J 2012
1/10 75 OHM J 2012
1/10 2.2K OHM J 2012
1/10 3.3K OHM J 2012
1/10 330 OHM J 2012
1/10 330 OHM J 2012
1/10 330 OHM J 2012
1/10 300K OHM J 2012
61
PARTS LIST
(DTQ-21T1FS)
Loc
RC519
RC520
RC521
RC522
RC523
RC532
RC533
RC534
RC535
RC536
RC537
RC538
RC539
RC540
RC541
RC542
RC544
RC545
RC546
RC547
RC548
RC549
RC550
RC551
RC552
RC603
RC604
RC605
RC606
RC607
RC608
RC610
RC611
RC612
RC613
RC614
RC615
RC616
RC617
RC618
RC619
RC620
RC645
RC646
RC647
RC648
RC701
RC703
RC704
Item Code
Item Name
Description
HRFT274JCA
HRFT561JCA
HRFT684JCA
HRFT222JCA
HRFT624JCA
HRFT222JCA
HRFT000-CA
HRFT102JCA
HRFT102JCA
HRFT162JCA
HRFT102JCA
HRFT102JCA
HRFT221JCA
HRFT102JCA
HRFT331JCA
HRFT391JCA
HRFT102JCA
HRFT432JCA
HRFT750JCA
HRFT432JCA
HRFT432JCA
HRFT202JCA
HRFT272JCA
HRFT153JCA
HRFT103JCA
HRFT222JCA
HRFT203JCA
HRFT822FCA
HRFT161FCA
HRFT102JCA
HRFT102JCA
HRFT102JCA
HRFT102JCA
HRFT222JCA
HRFT203JCA
HRFT222JCA
HRFT153JCA
HRFT152JCA
HRFT512JCA
HRFT153JCA
HRFT152JCA
HRFT512JCA
HRFT102JCA
HRFT103JCA
HRFT102JCA
HRFT103JCA
HRFT101JCA
HRFT101JCA
HRFT101JCA
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
1/10 270K OHM J 2012
1/10 560 OHM J 2012
1/10 680K OHM J 2012
1/10 2.2K OHM J 2012
1/10 620K OHM J 2012
1/10 2.2K OHM J 2012
1/10 0 OHM 2012
1/10 1K OHM J 2012
1/10 1K OHM J 2012
1/10 1.6K OHM J 2012
1/10 1K OHM J 2012
1/10 1K OHM J 2012
1/10 220 OHM J 2012
1/10 1K OHM J 2012
1/10 330 OHM J 2012
1/10 390 OHM J 2012
1/10 1K OHM J 2012
1/10 4.3K OHM J 2012
1/10 75 OHM J 2012
1/10 4.3K OHM J 2012
1/10 4.3K OHM J 2012
1/10 2K OHM J 2012
1/10 2.7K OHM J 2012
1/10 15K OHM J 2012
1/10 10K OHM J 2012
1/10 2.2K OHM J 2012
1/10 20K OHM J 2012
1/10 8.2K OHM F 2012
1/10 160 OHM F 2012
1/10 1K OHM J 2012
1/10 1K OHM J 2012
1/10 1K OHM J 2012
1/10 1K OHM J 2012
1/10 2.2K OHM J 2012
1/10 20K OHM J 2012
1/10 2.2K OHM J 2012
1/10 15K OHM J 2012
1/10 1.5K OHM J 2012
1/10 5.1K OHM J 2012
1/10 15K OHM J 2012
1/10 1.5K OHM J 2012
1/10 5.1K OHM J 2012
1/10 1K OHM J 2012
1/10 10K OHM J 2012
1/10 1K OHM J 2012
1/10 10K OHM J 2012
1/10 100 OHM J 2012
1/10 100 OHM J 2012
1/10 100 OHM J 2012
62
PARTS LIST
(DTQ-21T1FS)
Loc
RC705
RC706
RC707
RC708
RC709
RC710
RC711
RC712
RC713
RC714
RC715
RC716
RC717
RC718
RC719
RC720
RC721
RC722
RC723
RC724
RC725
RC726
RC727
RC728
RC729
RC730
RC731
RC732
RC733
RC734
RC736
RC737
RC740
RC742
RC743
RC744
RC745
RC746
RC747
RC748
RC749
RC750
RC815
RC817
RC901
RC902
RC903
RC904
RC911
Item Code
Item Name
Description
HRFT102JCA
HRFT102JCA
HRFT102JCA
HRFT472JCA
HRFT472JCA
HRFT150JCA
HRFT472JCA
HRFT101JCA
HRFT101JCA
HRFT102JCA
HRFT103JCA
HRFT103JCA
HRFT471JCA
HRFT102JCA
HRFT105JCA
HRFT102JCA
HRFT102JCA
HRFT473JCA
HRFT103JCA
HRFT623JCA
HRFT163JCA
HRFT103JCA
HRFT103JCA
HRFT102JCA
HRFT121JCA
HRFT102JCA
HRFT121JCA
HRFT102JCA
HRFT121JCA
HRFT102JCA
HRFT102JCA
HRFT102JCA
HRFT243JCA
HRFT103JCA
HRFT472JCA
HRFT102JCA
HRFT152JCA
HRFT222JCA
HRFT392JCA
HRFT102JCA
HRFT102JCA
HRFT514JCA
HRFT150JCA
HRFT103JCA
HRFT471JCA
HRFT471JCA
HRFT471JCA
HRFT271JCA
HRFT152JCA
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
1/10 1K OHM J 2012
1/10 1K OHM J 2012
1/10 1K OHM J 2012
1/10 4.7K OHM J 2012
1/10 4.7K OHM J 2012
1/10 15 OHM J 2012
1/10 4.7K OHM J 2012
1/10 100 OHM J 2012
1/10 100 OHM J 2012
1/10 1K OHM J 2012
1/10 10K OHM J 2012
1/10 10K OHM J 2012
1/10 470 OHM J 2012
1/10 1K OHM J 2012
1/10 1M OHM J 2012
1/10 1K OHM J 2012
1/10 1K OHM J 2012
1/10 47K OHM J 2012
1/10 10K OHM J 2012
1/10 62K OHM J 2012
1/10 16K OHM J 2012
1/10 10K OHM J 2012
1/10 10K OHM J 2012
1/10 1K OHM J 2012
1/10 120 OHM J 2012
1/10 1K OHM J 2012
1/10 120 OHM J 2012
1/10 1K OHM J 2012
1/10 120 OHM J 2012
1/10 1K OHM J 2012
1/10 1K OHM J 2012
1/10 1K OHM J 2012
1/10 24K OHM J 2012
1/10 10K OHM J 2012
1/10 4.7K OHM J 2012
1/10 1K OHM J 2012
1/10 1.5K OHM J 2012
1/10 2.2K OHM J 2012
1/10 3.9K OHM J 2012
1/10 1K OHM J 2012
1/10 1K OHM J 2012
1/10 510K OHM J 2012
1/10 15 OHM J 2012
1/10 10K OHM J 2012
1/10 470 OHM J 2012
1/10 470 OHM J 2012
1/10 470 OHM J 2012
1/10 270 OHM J 2012
1/10 1.5K OHM J 2012
63
PARTS LIST
(DTQ-21T1FS)
Loc
RC913
RC917
RC918
RC919
RC920
RC923
RC924
RC925
RC926
RC927
RC928
RC929
RC930
RC931
RC932
RC933
RLY1
RS801
SCT1
SF501
SW701
SW702
SW703
SW704
SW705
SW706
T401
T402
T801
U101
X501
X701
Z501
Z502
Z503
Z601
Item Code
Item Name
Description
HRFT201JCA
HRFT000-CA
HRFT000-CA
HRFT000-CA
HRFT000-CA
HRFT121JCA
HRFT201JCA
HRFT121JCA
HRFT241JCA
HRFT121JCA
HRFT241JCA
HRFT000-CA
HRFT000-CA
HRFT000-CA
HRFT000-CA
HRFT000-CA
5SC0101325
DSVC471D14
4859303030
5PM1859M-5S50101035
5S50101090
5S50101090
5S50101090
5S50101090
5S50101090
50D0000022
50H0000175
50M4242A7J
4859716730
5XEX3R579C
5XYR03276C
4850L03110
5PXPS45MB5PXFSH4R5D
4850L03810
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
SW RELAY
VARISTOR
SOCKET CRT
FILTER SAW
SW TACT
SW TACT
SW TACT
SW TACT
SW TACT
SW TACT
TRANS DRIVE
FBT
TRANS SMPS
TUNER VARACTOR
CRYSTAL QUARTZ
CRYSTAL QUARTZ
RESONATOR CERA
FILTER CERA
FILTER CERA
RESONATOR CERA
1/10 200 OHM J 2012
1/10 0 OHM 2012
1/10 0 OHM 2012
1/10 0 OHM 2012
1/10 0 OHM 2012
1/10 120 OHM J 2012
1/10 200 OHM J 2012
1/10 120 OHM J 2012
1/10 240 OHM J 2012
1/10 120 OHM J 2012
1/10 240 OHM J 2012
1/10 0 OHM 2012
1/10 0 OHM 2012
1/10 0 OHM 2012
1/10 0 OHM 2012
1/10 0 OHM 2012
HR-CR7 DC12V
SVC471D14A
ISMM03S
M1859M
KPT-1112 1C-1P
SKHV17910A
SKHV17910A
SKHV17910A
SKHV17910A
SKHV17910A
HD-15D
2002SPND
TSM-4242A7
DT9-NF07F
HC-49U 3.579545M (TP)
C-001R 32.768000KHZ 20PPM
CSB503F44
TPS-4.5MB TRAP (TAPPING)
SFSH4.5MDB
CSB503F58
64
DTQ-20T1FC DIFFERENT PARTS LIST
Loc
PCW1
Item Code
Item Name
Description
4859903610
POWER CORD AS
DJ-10W + BSP3
-1/2H = 2100
F801
5F1GB4021L
FUSE GLASS TUBE
4L/CSA TL 4A
125V MF51
RS801
DSVC271D14
VARISTOR
SVC271D14A
65
OPTION LIST
CN-201A/B MODEL(Inch, Mono, Stereo)
14 Inch
(Mono)
20 Inch
(Mono)
20Inch
(Stereo)
21 Inch
(Stereo)
DTQ-14Q1 SERIES, DTQ-14Q2 SERIES, DTQ-14Q3 SERIES, DTQ-14T1 SERIES, DTQ-14T2 SERIES
DTQ-20Q1 SERIES, DTQ-20Q2 SERIES, DTQ-20Q3 SERIES, DTQ-20T1AS
DTQ-20T2AS, DTQ-20T3AS
DTQ-20T1FS, DTQ-20T2FS, DTQ-20T3FS
DTQ-21T1FS, DTQ-21T2FS, DTQ-21T5FS, DTQ-21T9FS
CN-201A/B 14”/20”/21” OPTION(MAIN PCB)
Loc.
C404
C406
C421
CC506
CC509
J406
J407
J506
L401
L402
R407
R423
R426
RC302
RC303
RC309
RC311
RC312
RC543
RC550
RC551
RC924
T402
CRT
14 Inch(Mono)
1.6KV BUP 6000PF
200V PU 0.47MF
50V RSS 4.7MF
50V X7R 0.01MF
50V X7R 1000PF
INSERT
INSERT
*
*
*
*
1W 0.82 OHM
1/4 24K OHM
1/10 110K OHM
1/10 15K OHM
1/10 27K OHM
1/10 1K OHM
1/10 11K OHM
1/10 1K OHM
1/10 5.1K OHM
1/10 16K OHM
1/10 240 OHM
1401SPND
A34JLL40X
A34JLL40X:
CHILE, PERU
D.COIL DC-1450
COIL D.Y ODY-M1401N
ODY-M1401:
CHILE,PERU
20 Inch(Mono)
1.6KV BUP 7500PF
200V PU 0.51MF
50V RSS 4.7MF
50V X7R 0.01MF
50V X7R 1000PF
*
INSERT
*
L-76(76.5UH)
*
1W 2.7K OHM
1W 0.68 OHM
1/4 15K OHM
1/10 110K OHM
1/10 16K OHM
1/10 27K OHM
1/10 1K OHM
1/10 13K OHM
1/10 1K OHM
1/10 2.7K OHM
1/10 15K OHM
1/10 200 OHM
2002SPND
A48JLL40X
A48JLL40X:
CHILE, PERU
DC-2050
ODY-M2002N
ODY-M2002:
CHILE,PERU
20 Inch(Stereo)
1.6KV BUP 7500PF
200V PU 0.51MF
50V RSS 4.7MF
*
50V X7R 1000PF
*
INSERT
INSERT
L-76(76.5UH)
*
1W 2.7K OHM
1W 0.68 OHM
1/4 15K OHM
1/10 110K OHM
1/10 16K OHM
1/10 27K OHM
1/10 1K OHM
1/10 13K OHM
*
1/10 2.7K OHM
1/10 115K OHM
1/10 200 OHM
2002SPND
A48JLL40X
A48JLL40X:
CHILE, PERU
DC-2050
ODY-M2002N
ODY-M2002:
CHILE,PERU
66
21 Inch(Stereo)
1.6KV BUP 720PF
200V PU 0.47MF
50V RSS 4.7MF
*
50V X7R 1000PF
*
*
INSERT
L-76(76.5UH)
TRW-414M
1W 2.7K OHM
1W 0.68 OHM
1/4 15K OHM
1/10 110K OHM
1/10 15K OHM
1/10 9.1K OHM
1/10 1K OHM
1/10 13K OHM
*
1/10 2.7K OHM
1/10 15K OHM
1/10 200 OHM
2002SPND
A51JSW40X40X
A51JSW41X(G):
CHILE, PERU
DC-2080
ODY-F2101W(L)
ODY-F2101(L):
CHILE,PERU
CN-201A/B 14”/20”/21” AUDIO OPTION
Loc.
C603
C605
C606
C607
C608
C609
C610
C611
C612
C613
C614
C615
C616
C618
C619
C620
C621
C622
C623
C624
C625
C626
C627
C628
C629
C630
C631
C632
C633
C634
C635
C640
C641
C642
CA01
CA02
CAC02
CAC01
CAC02
CC601
CC602
CC604
CC617
CC631
I601
I602
I603
J050
J601
J602
J603
J604
14 Inch(Mono)
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
50V EU 0.012MF
*
*
*
63V MEU 0.33MF
*
*
50V RSS 47MF
*
50V RSS 2.2MF
50V X7R 0.1MF
*
*
*
*
*
*
*
*
1TDA7056
*
*
*
*
*
*
20 Inch(Mono)
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
50V EU 0.012MF
*
*
*
63V MEU 0.33MF
*
*
50V RSS 47MF
*
50V RSS 2.2MF
50V X7R 0.1MF
*
*
*
*
*
*
*
*
1TDA7056
*
*
*
*
*
*
20 Inch(Stereo)
63V MEU 0.15MF
50V RSS 2.2MF
50V RSS 0.47MF
25V RSS 100MF
50V RSS 2.2MF
50V RSS 10MF
50V RSS 10MF
50V RSS 1MF
50V RSS 1MF
63V MEU 0.047MF
50V RSS 10MF
63V MEU 0.1MF
50V RSS 4.7MF
25V RSS 100MF
50V RSS 10MF
25V RSS 100MF
63V MEU 0.47MF
63V MEU 0.22MF
50V RSS 4.7MF
50V RSS 10MF
50V RSS 4.7MF
50V RSS 4.7MF
50V RSS 2.2MF
50V EU 0.015MF
50V EU 0.015MF
50V RSS 2.2MF
*
63V MEU 0.15MF
63V MEU 0.33MF
63V MEU 0.33MF
*
50V EU 0.022MF
50V EU 0.022MF
*
50V RSS 2.2MF
50V RSS 2.2MF
*
50V X7R 0.1MF
50V X7R 0.1MF
50V CH 100PF
50V CH 100PF
50V X7R 8200PF
50V X7R 0.01MF
50V X7R 8200PF
TDA9852
*
TDA7057Q
INSERT
INSERT
INSERT
INSERT
INSERT
67
21 Inch(Stereo)
63V MEU 0.15MF
50V RSS 2.2MF
50V RSS 0.47MF
25V RSS 100MF
50V RSS 2.2MF
50V RSS 10MF
50V RSS 10MF
50V RSS 1MF
50V RSS 1MF
63V MEU 0.047MF
50V RSS 10MF
63V MEU 0.1MF
50V RSS 4.7MF
25V RSS 100MF
50V RSS 10MF
25V RSS 100MF
63V MEU 0.47MF
63V MEU 0.22MF
50V RSS 4.7MF
50V RSS 10MF
50V RSS 4.7MF
50V RSS 4.7MF
50V RSS 2.2MF
50V EU 0.015MF
50V EU 0.015MF
50V RSS 2.2MF
*
63V MEU 0.15MF
63V MEU 0.33MF
63V MEU 0.33MF
*
50V EU 0.022MF
50V EU 0.022MF
*
50V RSS 2.2MF
50V RSS 2.2MF
*
50V X7R 0.1MF
50V X7R 0.1MF
50V CH 100PF
50V CH 100PF
50V X7R 8200PF
50V X7R 0.01MF
50V X7R 8200PF
TDA9852
*
TDA7057Q
INSERT
INSERT
INSERT
INSERT
INSERT
Loc.
J605
J606
J607
J608
J609
J610
J611
J614
JAC01
JAC02
JC601
JC602
JC703
L601
L602
L603
L604
QC601
QC602
QC603
QC604
RAC03
RAC04
RC601
RC603
RC604
RC605
RC606
RC607
RC608
RC610
RC611
RC612
RC613
RC614
RC615
RC616
RC617
RC618
RC619
RC620
RC621
RC622
RC623
RC643
RC645
RC646
RC647
RC648
RC739
Z601
D601
14 Inch(Mono)
*
*
*
*
*
*
INSERT
INSERT
1/10 0 OHM
1/10 0 OHM
*
*
*
*
*
HC-3550
*
*
2SC2412K
*
*
*
*
1/10 10K OHM
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
1/10 13K OHM
1/10 5.1K OHM
1/10 6.2K OHM
1/10 10 OHM
*
*
*
*
1/10 1K OHM
*
*
20 Inch(Mono)
*
*
*
*
*
*
INSERT
INSERT
1/10 0 OHM
1/10 0 OHM
*
*
*
*
*
HC-3550
*
*
2SC2412K
*
*
*
*
1/10 10K OHM
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
1/10 13K OHM
1/10 5.1K OHM
1/10 6.2K OHM
1/10 10 OHM
*
*
*
*
1/10 1K OHM
*
*
20 Inch(Stereo)
INSERT
INSERT
INSERT
INSERT
INSERT
INSERT
*
*
*
*
1/10 0 OHM
1/10 0 OHM
1/10 0 OHM
HC-3550
HC-3550
*
56UH
2SC2412K
*
2SC2412K
2SC2412K
1/10 390 OHM
1/10 100K OHM
*
1/10 2.2K OHM
1/10 20K OHM
1/10 8.2K OHM F
1/10 160 OHM F
1/10 1K OHM
1/10 1K OHM
1/10 1K OHM
1/10 1K OHM
1/10 2.2K OHM
1/10 20K OHM
1/10 2.2K OHM
1/10 15K OHM
1/10 1.5K OHM
1/10 5.1K OHM
1/10 15K OHM
1/10 1.5K OHM
1/10 5.1K OHM
*
*
*
*
1/10 1K OHM
1/10 10K OHM
1/10 1K OHM
1/10 10K OHM
*
CSB503F58
UZ-8.2B (8.2V)
68
21 Inch(Stereo)
INSERT
INSERT
INSERT
INSERT
INSERT
INSERT
*
*
*
*
1/10 0 OHM
1/10 0 OHM
1/10 0 OHM
HC-3550
HC-3550
*
56UH
2SC2412K
*
2SC2412K
2SC2412K
1/10 390 OHM
1/10 100K OHM
*
1/10 2.2K OHM
1/10 20K OHM
1/10 8.2K OHM F
1/10 160 OHM F
1/10 1K OHM
1/10 1K OHM
1/10 1K OHM
1/10 1K OHM
1/10 2.2K OHM
1/10 20K OHM
1/10 2.2K OHM
1/10 15K OHM
1/10 1.5K OHM
1/10 5.1K OHM
1/10 15K OHM
1/10 1.5K OHM
1/10 5.1K OHM
*
*
*
*
1/10 1K OHM
1/10 10K OHM
1/10 1K OHM
1/10 10K OHM
*
CSB503F58
UZ-8.2B (8.2V)
ENGINEER NOTE
DAEWOO ELECTRONICS CO., LTD.
686, AHYEON-DONG, MAPO-GU,
SEOUL, KOREA.
C.P.O. BOX 8003 SEOUL KOREA
TELEX : DWELEC K28177-8
F A X : (02) 364-5588,5305
T E L : (02) 360-7360 ~ 4, 7315 ~ 7
S/M NO :CN201N-010
PRINTED DATE:APR. 1998