MobiCam DXR Touch User manual

 TABLE OF CONTENTS
Introduction
1
Radio Interferece Parameters
1
Package Contents
2
Monitor/Receiver
2
Camera/Transmitter
3
To Star t
Charging/Powering On
4
Locking the Screen
4
Set to Another Language
4
Pairing Camera and Monitor
5
Main Menu
6
Touch Navigation
Volume/Display
7
Lullabys
7
Night Light
7
Record
8
Play
9
Quad and Channel View
10
VOX (Voice Activation)
10
S etting
s
Monitor Settings
11-14
Camera Settings
15
Individual Channel & Convenience Icons
16
Webcam Use • Data/File Transfers
17
Audio/Video Out
18
Troubleshooting
18
Factory Default Settings
19
Battery Replacement
20
Product Safety
20
Proper Disposal
21
Limited Warranty
21
Addendum: Focusing Camera Lens
21
About Mobi® / Contact Mobi®
22
INTRODUCTION
Congratulations on the purchase of this MobiCam® DXR Touch Monitoring
System, which incorporates the latest advanced technology. To fully maximize and benefit from this product’s avanced features we highly recommend
you review these instructions. This 2.4 GHz Digital monitor enables you to
transmit picture and sound signals cordlessly, which is ideal for many situations suchs as monitoring a baby, young children or the elderly, or used as
office or warehouse monitoring system.
IMPORTANT: Use ONLY a fingertip or other NON-SHARP object to select touch screen
options. Using sharp objects can damage the screen and void the warranty.
RADIO INTERFERENCE PARAMETERS
FCC Statement
15.19: This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful interference and (2) This device must accept any interference received, including
interference that may cause undesired operation.
15.21: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC Radiation Exposure Statement
This equipment has been tested and complies with Federal Communications
Commission radiation exposure limits as set forth for uncontrolled environments. This equipment should be installed and operated with a minimum
distance of 20cm between the radiator and your body. This Camera must not
be co-located or operating in conjunction with any other antenna or Camera.
This equipment complies with FCC RF radiation exposure limits set forth for
an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or Camera. This device has been tested for compliance with FCC RF Exposure (SAR) limits in the
typical laptop computer configuration and this device can be used in desktop
or laptop computers via USB slots. This device and its antenna must not be colocated or operated in conjunction with any other antenna or Camera.
IC Statement
Operation of this device is subject to the following two conditions: 1. This
device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the
device.
1
PACKAGE CONTENTS
CAMERA
• 1 Camera/Transmitter
• 2 AC/DC Adaptors 5V 800mAh
• 1 Li-Ion Rechargeable Battery (for monitor only)
• 1 Attachable Strap Mount
• 1 Door/Drawer Hook Attachment
• 1 Wall Anchor Mount with Screw
• 1 USB to Mini USB Data Cord
• 1 AV-Out Cable
• 1 User Manual
Power ON
LED Indicator
(Note: See
Addendum
on page 21
for focusing
instructions)
Night
Light
DC Power
Input
Escape/Menu
Button
2-Way Talk
Button
Battery
Compartment
PAIR
Button
SD Card Slot
Battery
Compartment
Strap Mount
(underneath)
Lock Screen
Button
Combo
Screen Cover /
Fold-back Stand
DC Power Input /
Mini USB Output
Monitor / Receiver Unit
features:
• 3.5” QVGA resolution TFT touch panel screen
• VGA resolution (640*480) up to 25 frames per
second
• up to 250-300 meter range
• 2-way communication
• MENU/ESCAPE button
• PAIR Button
• TALK Button
• Lock Screen Button for disabling touch screen
• SD Card Slot up to 32 Gb (not included)
• Mini USB Output port (for connection to a PC
and charging)
Ridge-Grip
Surface Stand
(card not included)
AV
Output
2-Way Talk
Microphone
Night Vision
IR LEDs
Focus
Ring
PAIR
Button
Power ON
LED Indicator
ON/OFF
Button
2-Way Talk
Speaker
Retractable
Antenna
Camera
Lens
Retractable
Antenna
ON / OFF
Button
MONITOR
• 1 Monitor/Receiver
• A/V Output port
• DC Input (AC/DC adaptor included)
• Two-Color LED: solid green for power on;
flashing red for charging
• Quad-View split screen (up to 4 camera
capability)
• Main Menu with color icon display
• Rechargeable Li-ion Battery 3.7V 1200 mAh
(included for monitor only)
Microphone
2-Way Talk &
Lullaby Speaker
Camera / Transmitter Unit
A.
features:
PAIR Button
LED for Power ON / Pairing (flashes)
Microphone & Speaker
DC Input (AC/DC adaptor included)
Night Vision
Temperature Sensor and Alarm
VOX (Hi/Mid/Lo/Off ) controlled from receiver
Adjustable Volume from receiver
Adjustable TX Power (High-Low) from receiver
4 Pre-Recorded Lullaby choices
Night Light
Rechargeable Battery 3.7V 1500 mAh
(not included - sold separately)
• 2.4GHz Digital FHSS, 100% secure with full
privacy and interference free
•
•
•
•
•
•
•
•
•
•
•
•
C.
B.
D.
Positioning / Mounting Options
A. Horizontal to Slightly Angled Surfaces - Built-in Ridge-Grip Feet… B. Wall Mount Screw with
Drywall Anchor (included)… C. Door or Drawer Hook Mount / Stand (included)… D. Horizontal
Rails / Drawer Handles - Attachable Strap Mount (included)
WARNING: To prevent strangulation never place a power cord within reach of a child.
2
3
TO START
A. Plug one of the AC/DC adapters (they are interchangeable) into the monitor and allow it to
charge the Monitor Battery for at least 5-1/2 hours.
B. Plug the other AC/DC adapter into the camera. Turn the Camera On by holding the ON/OFF
Button down for several seconds. The green “Power On” Indicator lights when powered up.
C. Turn the Monitor On by holding its ON/OFF Button down for several seconds. Its “Power On”
Indicator will light up (green on battery power, red when charging) and the Mobi logo will
appear on the screen.
D. Press ESC Button to go to the Main Menu.
PAIRING: The monitor and camera are paired (wirelessly linked) by the manufacturer at the factory. If you ever need to relink the camera, or you want to pair Additional Cameras (sold separately)
you will need to pair each following the steps below:
NOTE: Before pairing be sure the camera and monitor are both turned on and both are
within 10 feet of each other.
NOTE: While viewing the Main Menu, if no
buttons are pressed, or the screen is not
touched after 30 seconds, the monitor will
automatically exit the Main Menu mode.
Main Menu
E. Press ESC Button once again to go to the
Camera View. Along the top and bottom
of the screen, small “Per Camera” Icons (explained on page 16) will appear over the
view from the camera, which should be on
and paired with the monitor.
IMPORTANT: Use ONLY a fingertip or other NON- SHARP object to select
touch screen options.
Camera View
Using sharp objects can
damage the screen and
void the warranty.
1. Power On the Monitor and Camera
2. Press and hold the Pair Button on the back of the Monitor until the “Pair” screen is displayed,
LOCKING THE SCREEN: If you slide the Lock Screen Button a LOCK icon will appear and the
touch-screen function will be disabled. Sliding the Lock Screen Button again will revert it back to
normal touch-screen function.
then release the button.
3. Press and release the Pair Button on the Monitor and select a camera number (1-4) to be
paired. The word “Pairing” appears below the icon of the selected camera as it waits to be
paired.
TO SET TO ANOTHER LANGUAGE: The monitor is set to English by default. The
MobiCam® DXR Touch can also display in French, German, Por tuguese, Spanish, or
Italian. To change the language follow these steps: press the ESC Button
touch Setting icon
touch System Setting
touch slider to See More List
select Language from the list
select a new Language
press the ESC Button
4. You have 10 seconds to press and hold the Pair Button on the back of the Camera to com plete Pairing, otherwise restart from step 2 above.
5. The word “OK” or “Failed” will be displayed on screen. If pairing Failed start again being sure
the camera is on and not too far away.
6. When Pairing shows as OK, press the ESC Button or the Return icon
additional cameras repeat the steps above.
4
5
to go back. To pair
MAIN MENU ... touch the ESC Button to open the Main Menu on screen
IMPORTANT: Use ONLY a fingertip or other NON-SHARP object to select touch screen
options. Using sharp objects can damage the screen and void the warranty.
Touch the appropriate icon to access all Settings
and Options.
VOLUME / DISPLAY LULLABYS
adjust
select
• Sound Volume
• Camera Number
• Screen Contrast
• Lullaby Choice
• Screen Brightness
• Lullaby Volume
NIGHT LIGHT
select
• Camera Number
• Night Light On
• Night Light Off
RECORD
select
• Take Photo
• Record Video
• Format SD Card
• SD Information
• Time/Date Stamp
TOUCH NAVIGATION ... touch the ESC Button to start at Main Menu
touch a Menu Icon ... to open a Function Screen ... to check or change a Function
touch
VOLUME / DISPLAY
– or + icons to adjust...
Monitor Volume
Screen Contrast
Screen Brightness
LULLA
BYS
select a Camera...
select one of four Lullabys
deactivate all Lullabys...
adjust Lullaby Volume
PLAY
QUAD / CHANNEL VOX (Voice Activation)
select / play
select
select
• Recorded Video • Quad View
• Camera Number
• Recorded Photo • Specific CAMs
• VOX On/Off
• Delete Files
• Switch CAMs
• Sound Sensitivity
• Auto Record On/Off
SETTINGS
for the Monitor
• Date/Time
• Time Alarm
• Auto Switch Time
• AV Out Format
• Recording Schedule
• Zoom/Pan/Tilt
• Screen Timeout
• Touch Calibration
• USB Output
• SD Card Update
SETTINGS
for the Camera
• Temperature Alarm
• TX Power/Volume
NIGHT LIGHT
select a Night Light icon for the
camera you wish to control...
shown with the Night Light ON
shown with the Night Light OFF
(the light bulb image in the icon
changes to yellow when ON and
back again when OFF)
• Languages
• Reset to Default
• About / Version
HINT: To move back one screen touch Return icon
6
or go to camera view by pressing the ESC Button.
7
TOUCH NAVIGATION ... touch the ESC Button to start at Main Menu
touch a Menu Icon ... to open a Function Screen ... to check or change a Function
TOUCH NAVIGATION ... touch the ESC Button to start at Main Menu
touch a Menu Icon ... to open a Function Screen ... to check or change a Function
select Video or Picture folder option
Photo
Playback of Recordings
PLAY
touch one of four functions...
RECORD
goes to camera view where you can
take an store still photo when you
touch the
Still
Camera
icon
Video
NOTE: All recording
functions require an
SD memory card
(max 32 Gb).
NOTE: While recording
no other functions are
available until recording is stopped.
goes to camera view where you can
record a video (with sound) of the
scene when you touch the REC icon
to start recording - and press it again
to stop recording
SD Format
lets you Format / Erase an SD
memory card
select a Video or Picture file to
Play / View (videos are .asf
format and pictures are .jpg
format)
as you view a Recorded Video file
the screen will also show...
select OK
or Cancel
Return icon (upper left) - used to
exit the playback at any time
Elapsed Time / Total Play Time /
and Date-Time Stamp (upper
right)
Video Play controls (bottom center)
Delete icon (trash can bottom
right)
when the Delete icon is touched
you then see this screen to confirm
file deletion with an OK
SD Info
displays Total Size, Used Space,
and Free Space on an SD card in the
SD card slot
select a folder for the Date of
the Recording (shows as year/
month/day with no separations)
HINT: To move back one screen touch Return icon
or go to camera view by pressing the ESC Button.
8
HINT: To move back one screen touch Return icon
or go to camera view by pressing the ESC Button.
9
TOUCH NAVIGATION ... touch the ESC Button to start at Main Menu
touch a Menu Icon ... to open a Function Screen ... to check or change a Function
TOUCH NAVIGATION ... touch the ESC Button to start at Main Menu
touch a Menu Icon ... to open a Function Screen ... to check or change a Function
QUAD / CHANNEL
NOTE: All cameras
must be Paired to
the monitor for viewing access. (Refer to
active Camera icon (shown in color if
actively paired) to be your only video
channel in this mode. The screen will
then show the view from that camera.
From the Monitor Setting list...
Quad View
Pairing on page 5.)
B from Quad/Channel screen, select the
on the Setting Screen, simply touch
the System Setting icon (two gears)
to access monitor functions...
A from Quad/Channel screen, select an
B
C
Monitor Setting
SETTINGS
Single Camera View
A
choose from these options...
NOTE: In Quad mode,
touching any active
camera image changes
to that full screen single
camera view. Also sound
only from the last camera in full screen mode
can be monitored.
select Date/Time
Quad icon which then shows you all
currently paired camera views (up to
4) on screen simutaniously.
touch any value, then touch the
arrows to adjust value up or down
Note: Only paired cameras will show
on the quad with any unused camera
views left blank.
Auto Scan View
C from Quad/Channel screen, select the
NOTE: In Auto Scan
mode (indicated by
this symbol) you can
select which cameras
to include and the scan
time between each
camera. (Refer to Auto
From the Monitor Setting list...
Auto icon to begin alternating full
screen views from each paired camera (up to 4) automatically changing
from one camera view to the next
touch Time Alarm
touch any value, then touch the
arrows to adjust value up or down
Switch Time on page 11.)
touch Alarm On or Alarm Off
touch OK to set
VOX
Sound Activated Mode (VOX)
Sound Activated Monitoring
From the Monitor Setting list...
select a paired Camera icon
(the ones in color)
press OK to save changes
then select from 3 options...
touch Auto Switch Time
VOX (set to On or Off )
select a camera switching interval
(5 sec to 60 sec)
VOX Sound Sensitivity
(set to High, Med or Low)
NOTE: VOX keeps monitor
(picture and sound) off
until the camera detects a
sound, which automatically turns the monitor back
on. This helps prevent false
alarms and allows parents
more rest.
check the cameras to be included in
auto switching mode
Sound-Activated Recording
(set to Yes or No - must have an
SD card in the Monitor to record)
touch OK to set
HINT: To move back one screen touch Return icon
10
or go to camera view by pressing the ESC Button.
HINT: To move back one screen touch Return icon
or go to camera view by pressing the ESC Button.
11
TOUCH NAVIGATION ... touch the ESC Button to start at Main Menu
TOUCH NAVIGATION ... touch the ESC Button to start at Main Menu
touch a Menu Icon ... to open a Function Screen ... to check or change a Function
touch a Menu Icon ... to open a Function Screen ... to check or change a Function
SETTINGS (cont.)
SETTINGS (cont.)
Monitor Setting (cont.)
Monitor Setting (cont.)
From the Monitor Setting list...
From the Monitor Setting list...
select TV Out Format
touch Video Off Timeout
touch the timer icon to choose
between non-active (X) or active
(no X) Timeout Mode
choose either PAL or NTSC video
format (US standard is NTSC)
touch OK to set
From the Monitor Setting list...
From the Monitor Setting list...
select Recording Schedule
select Touch Calibration
touch any value and then touch the
up and down arrows to adjust time
touch the + icons as they appear
in each corner of the screen (this
calibrates the monitor for best
touch screen accuracy)
once all four corners are touched,
tap EXIT to return to the Monitor
Setting list
to activate press On
(or OFF to deactivate)
From the Monitor Setting list...
select Zoom/Pan/Tilt and go to the
camera scene with Zoom/Pan/Tilt
icons overlaying the image...
to Zoom-In touch the + icon
(maximum of 3.0 - to -1 enlargement)
Zoom / Pan / Tilt
to Zoom-Out touch the – icon
to Pan or Tilt touch the arrow icons
(you can Pan or Tilt only after you
have zoomed in)
if active, touch the – or + icons to
set the limit at which time the video
will automatically Timeout (turn
off )
NOTE: Press the ESC Button to return
to the video image without Zoom/
Pan/Tilt icons overlaying it.
From the Monitor Setting list...
touch USB Output
select the Top icon for Charging
the monitor via the AC Adapter
(included)
Language
select the Middle icon to use the
system as a USB Webcam on a PC*
via the USB Data Cable (included) or...
select the bottom icon for PC file
transfer mode to or from an SD
Card in the monitor via the
included USB Data Cable
touch OK to set
* See page 17 for details on using the USB Output for viewing
video or transferring video or photo files to a PC.
HINT: To move back one screen touch Return icon
or go to camera view by pressing the ESC Button.
12
HINT: To move back one screen touch Return icon
or go to camera view by pressing the ESC Button.
13
TOUCH NAVIGATION ... touch the ESC Button to start at Main Menu
TOUCH NAVIGATION ... touch the ESC Button to start at Main Menu
touch a Menu Icon ... to open a Function Screen ... to check or change a Function
touch a Menu Icon ... to open a Function Screen ... to check or change a Function
SETTINGS (cont.) Language
Language
Camera Settings
SETTINGS (cont.)
Monitor Setting (cont.)
on the Setting Screen, simply touch
the Camera icon (on the bottom
line) for the one you wish to control
the settings for...
From the Monitor Setting list...
NOTE: Though shown here for reference, SD Card Update is to be used ONLY
for Updating System Firmware,
which would be downloaded and put
onto an SD card in order to be installed
using this option. Specific instructions
will be provided to registered users
regarding any new firmware.
From the Camera Setting screen...
From the Monitor Setting list...
touch Temperature/Alarm
set ºF or ºC (default is ºF)
touch Language
Language
English
French
German
Portuguese
Spanish
Italian
touch the thermometer icon
touch one of the 6 specific Languages you want the monitor to
show in all text displays
set the maximum and minimum
alarm temperature range
set the Alarm to be On or Off
From the Monitor Setting list...
touch Factory Default
choose OK to reset all settings,
or Cancel if you change your
mind
From the Monitor Setting list...
From the Camera Setting list...
touch About & Version
touch Tx Power/Volume
here you will see the product
name and manufacturer, and
the latest version of the installed
firmware
Language
adjust the Camera Speaker
Volume (top icon) up or down for
the Two-Way Talk function
set the Transmit Range Power
(lower icon) on High or Low
HINT: To move back one screen touch Return icon
or go to camera view by pressing the ESC Button.
14
if On, set the Alarm Time (from 5
to 60 seconds)
NOTE: When the room temperature
(where the camera is) goes above or
below the temperature range you
set, the monitor will sound an alarm
and the small Temperature icon on
the monitor screen will flash showing
the out-of-range temperature in that
room. The ESC Button will temporarily silence the repeating alarm
until the temperature returns to the
set range, or you turn the Alarm Off
from this screen.
Language
NOTE: Only Paired camera icons
will show in color and be active
for touch control.
HINT: To move back one screen touch Return icon
or go to camera view by pressing the ESC Button.
15
INDIVIDUAL CHANNEL and CONVENIENCE ICONS
IMPORTANT: Use ONLY a fingertip or other NON-SHARP object to select touch screen
options. Using sharp objects can damage the screen and void the warranty.
Specific small icons are created for each paired camera at the top edge of the screen which relate
to that individual camera (except Battery Level, which is for the monitor only). To use them...
just observe or touch one of the following Individual Channel icons to either...
A... view current Camera Number, or change to the next camera you want to view
B... view current VOX level, or change VOX sound sensitivity level for that camera
C... view Lullaby status, change the Lullaby selection, or turn off Lullabys from that camera
D... add Zoom / Pan / Tilt controls over the scene to manipulate the image from that camera
NOTE: Other individual camera icons appear for informational purposes, such as
Room Temperature, Switching Mode and Signal Strength, and when in
Quad Mode, each camera screen shown will also display the Signal Strength of that
particular camera.
A
Camera
Number
WEBCAM USE
B
VOX
Level
C
Lullaby
Status
D
Switching Battery Level Signal
Room
Temperature Mode (On) (monitor) Strength
Zoom /
Pan / Tilt
To view a larger version of the monitor screen on your PC* screen...
Note: Using this feature allows viewing only on the computer. Once USB Connection
is established the monitor screen is turned off and all features and buttons (with the
exception of the ESC Button) will not be functional.
1. Set the USB Output on the monitor to the Webcam icon (refer to page 13)
2. Using the USB Cord (included), connect the monitor to an available USB port on your PC*
3. Wait for your computer to automatically recognize and install the appropriate drivers and you
receive a Successful Installation message.
4. Once you have installed the device driver, your MobiCam® DXR Touch can be utilized as a wireless
webcam.
5. Once the picture from the monitor is displayed on your computer screen, pressing the ESC Button on
the monitor toggles between Single and Quad View modes.
The DXR Touch can be used with Skype®, Windows Messenger®, Google Talk® and Yahoo Messenger®.
When utilizing Skype®, Windows Messenger®, Google Talk® or Yahoo Messenger®, please refer to their
documentation for techical support.
* The MobiCam® DXR Touch is only compatable with Windows® PCs.
DATA/FILE TRANSFERS
DATE/TIME STAMP
Year/Month/Day
Hour/Minute/Second
To transfer photo and video files from the monitor to your PC* ...
Note: Using this feature allows viewing only on the computer. Once USB Connection
is established the monitor screen is turned off and all features and buttons (with the
exception of the ESC Button) will not be functional.
1. Set the USB Output on the monitor to the USB Connection icon (refer to page 13)
2. Using the USB Cord (included), connect the monitor to an available USB port on your PC*
3. Wait for your computer to automatically recognize and show the outside Memory Device
4. You may then move or copy files from the SD Card (not included) as you normally would with
any such storage device (provided an SD Card is in the monitor and has data stored on it)
direct to
VOLUME
direct to
PLAY
direct to
RECORD
1
2
3
* The MobiCam® DXR Touch is only compatable with Windows® PCs.
Each paired camera scene also displays Convenience Icons (shown along the bottom of the screen)
so you can either view the current Date/Time Stamp or...
touch and bypass the Main Menu to...
1... instantly adjust Volume controls for that camera
2... instantly access the Play Video / View Photo control panel
3... instantly Record Video from that camera...with just one touch!
16
17
AUDIO/VIDEO OUT
FACTORY DEFAULT SETTINGS
You can hear and see audio/video output on a T V or
other AV device directly from your DXR Touch monitor.
Item
When the AV OUT cord is connected to an external device, the DXR Touch monitor screen will
automatically turn off. Please refer to the manual for the AV device you are connected to for proper input selection and operation.
TROUBLESHOOTING
Problem
Solution
Monitor will not turn on
• Check AC/DC connection
• Confirm power outlet is working properly
• Charge Battery Pack
Monitor on but no picture
• Confirm “Audio Only” mode is not selected
• Confirm “VOX” mode is OFF
• Confirm there are no obstructions in front of camera
• Confirm camera and monitor are paired properly
Camera will not turn on
Battery does not recharge
Connection is lost
Volume
5
0-9
Contrast
5
0-9
Brightness
5
0-9
Date & Time
2011/09/01,08:00
Alarm Time
Off, 09:00
On , Off
Date Time Stamp
Off
On , Off
Auto Switch time
5s
5s,10s,30s,1min
Recording schedule
Off
On , Off
Start Time : 12:00:00
Final Time: 12:11:00
• Check AC/DC connection.
• Check battery pack connection in the monitor.
• Confirm power outlet is working properly
• Confirm batteries are placed correctly in monitor
Zoom
1.0
1.0 to 3.0
TV out format
PAL
PAL,NTSC
Monitor Video Off Timeout
Off, 60s
From 5s to 180s
VOX setting
Off
High, Middle, Low, Off
Lullaby
Off
Off, Lull 1, Lull 2, Lull 3, Lull 4
Temperature setting
ºF
ºF - ºC
Min 59ºF - Max 86ºF
50ºF - 122ºF
Alarm Off
On/Off, 5s,10s,30s,1m (increments)
Volume
5
0-9
TX Power
High
High, Low
Night Light
Off
Off, On
18
Camera setting value
• Check AC/DC connection
• Confirm power outlet is working properly
• Confirm monitor and camera are ON.
• Confirm AC/DC adapter is connected properly
• Confirm battery has sufficiant power.
• Place camera and monitor near each other and press
camera Pair button to relink camera and monitor.
• Reduce distance between camera and monitor.
• Remove or avoid other wireless products that may
be near camera or monitor.
Range
Monitor setting value
Simply connect the AV OUT Cord (included) to the AV OUT jack on the right side of the monitor
and connect the other ends (three RCA connectors) to the Audio and Video Input jacks on your TV,
DVR, or Camcorder, and select the appropriate input setting on that AV device.
Default value
19
BATTERY REPLACEMENT
Monitor Battery (included)
Li-Ion 3,7V 1200 mAh
PROPER DISPOSAL
Camera Battery (not included, sold separately, Mobi part
# 70216) Li-Ion 3,7V 1500 mAh
If you eventually dispose of the DXR Touch Monitor, Camera, Batteries, or AC Adapters, do so in
accordance with current federal, state and local regulations. As a consumer, you may be obligated
by law to recycle used batteries.
Do not mix products bearing the WEEE symbol (crossed out trash bin icon) with
your general household waste.
For the correct collection and treatment of these products take them to the
collection points designated by your local authority. Alternatively, contact the
supplier that sold you the product.
LIMITED WARRANTY
PRODUCT SAFETY
This product is not intended to be used as a medical monitor
and its use should not replace adult supervision.
CAUTION
• Periodically examine this product for damage to the cord, housing or other parts that may result
in the risk of fire, electric shock or serious injury. Do not operate any product with a damaged
cord or plug. If the product malfunctions, or is damaged in any manner, please contact the
manufacturer for examination and repair to avoid a potentially serious hazard.
• Never use the camera, monitor, or AC adapters near water (i.e. bathtub, sink, etc.).
• Always use the camera and the monitor where there is adequate ventilation. To prevent
overheating keep the camera and the monitor away from heat sources such as radiators, heat
registers, stoves, or other appliances that produce heat.
• Use only a dry cotton cloth to keep the units free of dust. Do not use a damp cloth, water, or
liquid cleaner of any kind.
• Remove the battery from either unit during long periods of non-use, as batteries may leak.
• Unplug the AC adapters from the monitor and the camera during periods of non-use. To
disconnect from the electrical outlet, grip the transformer and pull from the power socket.
Never remove by pulling the cord.
• Only use the Monitoring System with the supplied power adapters.
ADDENDUM: Camera Focus Adjustment Instructions
Focus
Ring
Occasionally you may need to adjust the camera lens for best focus.
Note: The camera lens will only turn less than 45 degrees in either direction.
Avoid any forceful turns which could damage the camera and possibly
void the warranty.
1) Have the monitor turned on and near the camera you want
to adjust.
2) With the camera on, place and point it to the area it will be
monitoring.
3) While viewing the camera image on the monitor, grip the
silver ring around the camera lens (and the LEDs around it),
and then slowly and gently turn the ring.
4) When the video picture on the monitor is at the sharpest
release the focus ring and leave it set at that position.
WARNING
Mobi Technologies, Inc. warrants this product to be free from defects in material and workmanship for a period of ninety (90) days from the date of purchase. Should this product prove to be
defective at any time during the warranty period, Mobi Technologies, Inc. will, at its option, either
replace or repair it without charge. After the warranty period, a service charge will be applied for
replacement of parts or labor for repair. If you suspect that the product is malfunctioning or is
defective, please call Mobi toll free at 1. 877. 662.4462 and ask for the Service Department. If the
problem still persists after consulting with our Service Department, you may return the product
to obtain warranty service. Please return it to Mobi along with a dated sales receipt from the place
of purchase to verify that it is within the authorized warranty period. This warranty does not cover
damage caused by accident, misuse, abuse, improper maintenance, unauthorized modification,
or connection to an improper power supply. A fee may be charged for repair resulting from such
damage. This warranty excludes all incidental or consequential damages and any liability other
than what is stated above.
This product is not a toy. Keep out of reach of children. To prevent strangulation never place a
power cord within reach of a child.
20
21