User manual
Dishwasher
ZDF 312
Thank you for selecting our
appliance
We wish you lots of enjoyment with your new
appliance and we hope that you will consider
our brand again when purchasing household
appliances.
Please read this user manual carefully and
keep it throughout the product life cycle as a
reference document. The user manual should
be passed on to any future owner of the
appliance.
Contents
Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ 3
Unloading the dishwasher _ _ _ _ _ _ _ _ 18
Control panel _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 4
Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ 19
Washing programmes _ _ _ _ _ _ _ _ _ _ _ 8
Environmental concerns _ _ _ _ _ _ _ _ _ 20
First use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 9
Something not working _ _ _ _ _ _ _ _ _ 21
Set the water softener _ _ _ _ _ _ _ _ _ _ _ 9
Technical data _ _ _ _ _ _ _ _ _ _ _ _ _ _ 23
Filling with dishwasher salt _ _ _ _ _ _ _ 11
Consumption values _ _ _ _ _ _ _ _ _ _ _ 23
Filling with rinse aid _ _ _ _ _ _ _ _ _ _ _ 12
Hints for test institutes _ _ _ _ _ _ _ _ _ _ 23
Adjusting the dosage of rinse aid _ _ _ _ 12
Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 24
Loading cutlery and dishes _ _ _ _ _ _ _ 13
Guarantee/Customer Service _ _ _ _ _ _ 27
Use of detergent _ _ _ _ _ _ _ _ _ _ _ _ _ 16
European Guarantee _ _ _ _ _ _ _ _ _ _ _ 29
"3 in 1 function" _ _ _ _ _ _ _ _ _ _ _ _ _ 17
www.electrolux.com _ _ _ _ _ _ _ _ _ _ _ 30
2
Safety information
In the interest of your safety and to ensure the
correct use, before installing and first using the
appliance, read this user manual carefully, including its hints and warnings. To avoid
unnecessary mistakes and accidents, it is important to ensure that all people using the
appliance are thoroughly familiar with its operation and safety features. Save these instructions and make sure that they remain with the
appliance if it is moved or sold, so that everyone
using it through its life will be properly informed
on appliance use and safety.
Correct use
• This dishwasher is only intended for washing
household utensils suitable for machine
washing.
• Do not put any solvents in the dishwasher.
This could cause an explosion.
• Knives and other items with sharp points
must be loaded in the cutlery basket with
their points down or placed in a horizontal
position in the upper basket.
• Only use products (detergent, salt and rinse
aid) suitable for dishwashers.
• Avoid opening the door whilst the appliance
is in operation, hot steam may escape.
• Do not take any dishes out of the dishwasher
before the end of the dishwashing cycle.
• After use, isolate the appliance from the
power supply and turn off the water supply.
• This product should be serviced only by an
authorised service engineer, and only genuine spare parts should be used.
• Under no circumstances should you attempt
to repair the machine yourself. Repairs carried out by inexperienced persons will cause
injury or serious malfunctioning. Contact
your local Service Force Centre. Always insist on genuine spare parts.
General safety
• Dishwasher detergents can cause chemical
burns to eyes, mouth and throat. Could endanger life! Comply with the safety instructions of the dishwasher detergent
manufacturer.
• The water in your dishwasher is not for drinking. Detergent residues may still be present
in your machine.
• Ensure that the door of the dishwasher is
always closed when it is not being loaded or
unloaded. In this way you will avoid anybody
tripping over the open door and hurting
themselves.
• Do not sit or stand on the open door.
Child safety
• This appliance is designed to be operated
by adults. Don’t allow children to use the
dishwasher unsupervised.
• Keep all packaging well away from children.
There is risk of suffocation.
• Keep all detergents in a safe place out of
children’s reach.
• Keep children well away from the
dishwasher when the door is open.
3
Installation
• Check your dishwasher for any transport
damage. Never connect a damaged machine. If your dishwasher is damaged contact your supplier.
• All packaging must be removed before use.
• Any electrical and plumbing work required to
install this appliance must be carried out by
a qualified and competent person.
• For safety reasons it is dangerous to alter
the specifications or attempt to modify this
product in any way.
• Never use the dishwasher if the electrical
supply cable and water hoses are damaged;
4
or if the control panel, work top or plinth area
are damaged such that the inside of the appliance is freely accessible. Contact your
local Service Force centre, in order to avoid
hazard.
• All sides of the dishwasher must never be
drilled to prevent damage to hydraulic and
electric components.
CAUTION!
For electrical and water connection carefully
follow the instructions given in specific paragraphs.
Control panel
1
2
3
4
5
On/Off button
Programme selection buttons
Delay start button
Indicator lights
Function buttons
Setting mode
IMPORTANT!
Always remember that when performing operations as:
– selecting a washing programme,
– setting the water softener,
the appliance MUST be in setting mode:
• Press On/Off button, ALL programme selection button lights are illuminated = appliance
in setting mode.
• Press On/Off button, ONLY a programme
button light is illuminated = last performed
programme still set.
In this case the programme has to be cancelled
(see instructions "Cancel a washing programme in progress").
5
Function buttons
In addition to the dishwashing programme selection,
the following functions can also be set with the help of
these buttons.
– the setting of the water softener,
– the cancelling of a programme in progress.
Programme selection buttons
• Starting the washing programme:
1. Press the On/Off button.
2. Press the button corresponding to the required
programme, the corresponding light remains illuminated while the other programme lights turn off.
3. After about 3 seconds from the last pressure of a
button the programme starts automatically.
IMPORTANT!
Once the programme has started, if you want to
change the selection made you must cancel the washing programme in progress.
• Cancel the washing programme in progress:
• Press and hold simultaneously function buttons B
and C until ALL programme button lights will illuminate.
• Release function buttons B and C.
• Switch off the machine by pressing the On/Off button or select a new washing programme (check that
there is detergent in the detergent dispenser.
6
Delay start button
This option allows the start of the programme to be
delayed by 3 or 6 hours. Before selecting the washing
programme, press the On/Off button and then press
the delay start button until the light corresponding to
3h or 6h illuminates.
Press the button corresponding to the required washing programme, the countdown will start automatically
after about 3 seconds.
Once the countdown has elapsed the washing programme will start automatically. The delay start light
will turn off.
• Cancel the delay start in progress:
Press the delay start button until the lights corresponding to 3h or 6h are off. The selected washing
programme will start automatically.
IMPORTANT!
It is possible to select a washing programme and the delay start also with the door slightly opened. In this case
the start of the programme or the countdown will occur after the closure of the door. Until that moment it is
possible to modify the set made.
Indicator lights
Wash
1)
Illuminates when the washing and rinsing phases are
running.
End of programme
Illuminates when the washing programme has ended.
It also has added functions of visual signalling as:
• the setting of the water softener,
• intervention of an alarm due to the malfunction of
the machine.
3 in 1 function
Indicates the activation/deactivation of the "3 in 1 function" (see "3 in 1 function") .
Salt refilling
Illuminates when special salt needs to be filled.
It can remain illuminated several hours after the salt
has been filled.
2)
7
Indicator lights
Illuminates when rinse aid needs to be filled.
Rinse aid
2)
1) As soon as you select a washing programme, the phase indicator lights for that programme will start flashing. As the programme
starts, the phase indicator lights turn off except for the indicator light of the phase in progress which will remain lit with a static
light.
2) The salt and rinse aid indicator lights are never illuminated while a washing programme is running even if filling with salt and
rinse aid is necessary.
Washing programmes
Programme
Degree of soil
Type of load
Programme description
Intensive 70°
Heavy soil
Crockery, cutlery, pots
and pans
Prewash
Main wash
2 intermediate rinses
Final rinse
Drying
Normal 65°
Normal soil
Crockery, cutlery, pots
and pans
Prewash
Main wash
1 intermediate rinses
Final rinse
Drying
Eat-Load-Run
Light soil
Crockery and cutlery
Main wash
Final rinse
Normal soil
Crockery and cutlery
Prewash
Main wash
1 intermediate rinse
Final rinse
Drying
1)
Bio 50°
2)
8
Programme
Rinse and Hold
Degree of soil
Type of load
Any.
Partial load (to be completed later in the day).
Programme description
1 cold rinse (to avoid food
scraps from sticking
together).
This programme does not
require the use of detergent.
1) Ideal for washing a partially loaded dishwasher. This is perfect daily programme, made to meet the needs of a family of 4
persons who only wish to load breakfast and dinner crockery and cutlery.
2) Test programme for test institutes.
First use
Before using your dishwasher for the first time:
• Ensure that the electrical and water connections comply with the installation instructions
• Remove all packaging from inside the appliance
• Set the water softener
• Pour 1 litre of water inside the salt container
and then fill with dishwasher salt
• Fill the rinse aid dispenser
If you want to use combi detergent tablets such
as: "3 in 1", "4 in 1", "5 in 1" etc... set the 3 in 1
function (see "3 in 1 function").
Set the water softener
The dishwasher is equipped with a water
softener designed to remove minerals and salts
from the water supply, which would have a detrimental or adverse effect on the operation of
the appliance.
The higher the content of these minerals and
salts, the harder your water is. Water hardness
is measured in equivalent scales, German de-
grees (°dH), French degrees (°TH) and mmol/
l (millimol per litre - international unit for the
hardness of water).
The softener should be adjusted according to
the hardness of the water in your area. Your
local Water Authority can advise you on the
hardness of the water in your area.
9
Water hardness
Adjusting the water hardness
setting
Use of salt
°dH
°TH
mmol/l
manually
electronically
51 - 70
91 - 125
9,1 - 12,5
2
level 10
yes
43 - 50
76 - 90
7,6 - 8,9
2
level 9
yes
37 - 42
65 - 75
6,5 - 7,5
2
level 8
yes
29 - 36
51 - 64
5,1 - 6,4
2
level 7
yes
23 - 28
40 - 50
4,0 - 5,0
2
level 6
yes
19 - 22
33 - 39
3,3 - 3,9
2
level 5
yes
15 - 18
26 - 32
2,6 - 3,2
1
level 4
yes
11 - 14
19 - 25
1,9 - 2,5
1
level 3
yes
4 - 10
7 - 18
0,7 - 1,8
1
level 2
yes
<4
<7
< 0,7
1
level 1
no
The water softener must be set in both ways:
manually, using the water hardness dial and
electronically.
Setting the water softener manually (see table)
The water softener is factory set at position 2.
Set switch to position 1 or
2
Setting the water softener electronically (see table)
IMPORTANT!
The water softener is factory set at position 5.
10
• The dishwasher must be switched off.
Switch on the dishwasher by pressing the On/Off
button.
• Press and hold simultaneously function buttons B
and C until the lights of function buttons A , B and
C start flashing.
• Release the buttons and then press function button
A; the lights of function buttons B and C turn off while
function button A goes on flashing. At the same time
End of programme light starts to flash.
The number of flashes of the End of programme
light corresponds to the current level.
• The End of programme light might flash 5 times,
for example. The flashing is repeated every 5 seconds.
• To change the level, press function button A. Each
time the button is pressed the level increases. (Level
1 follows level 10).
• The End of programme light indicates the new setting. (For the selection of the new level see the
chart).
• To memorise the operation, switch off the
dishwasher by pressing the On/Off button.
Filling with dishwasher salt
CAUTION!
Use only special salt suitable for dishwashers.
Unscrew the cap.
Only before filling with Using the funnel provided,
salt for the first time, fill pour in the salt until the
the salt container with wa- container is filled with salt.
ter.
11
IMPORTANT!
Immediately start a complete programme.
IMPORTANT!
Water will overflow from the container as salt is added.
Remove any trace of salt. Replace the cap tightly
turning it clockwise until it
stops with a click.
IMPORTANT!
Top up the special salt when the light on the
control panel illuminates.
Filling with rinse aid
Open the lid.
Fill up with rinse aid. The Clean up any rinse aid
maximum level for filling is which overflows. Close
the lid and press until it
indicated by "max"
locks.
IMPORTANT!
CAUTION!
Never fill the rinse aid dispenser with any other sub- Top up the rinse aid when the light on the control panel
stances (e.g. dishwasher cleaning agent, liquid deter- illuminates.
gent). This would damage the appliance.
12
Adjusting the dosage of rinse aid
Increase the dose if there are drops of water or
lime spots on the dishes after washing.
Open the lid.
Reduce the dose if there are whitish streaks on
the dishes or a bluish film on glassware or knife
blades.
Set the dosage level. (The Close the lid and press undose is factory set in po- til it locks.
sition 4).
Loading cutlery and dishes
Sponges, household cloths and any object that
can absorb water may not be washed in the
dishwasher.
• Before loading the dishes, you should:
– Remove all left over food and debris.
– Soften remnants of burnt food in pans
• When loading the dishes and cutlery, please
note:
– Dishes and cutlery must not impede the
rotation of the spray arms.
– Load hollow items such as cups, glasses,
pans, etc. with the opening downwards so
that water cannot collect in the container
or a deep base.
– Dishes and items of cutlery must not lie
inside one another, or cover each other.
– To avoid damage to glasses, they must
not touch.
– Lay small objects in the cutlery basket.
• Plastic items and pans with non stick coatings have a tendency to retain water drops;
these items will not dry as well as porcelain
and steel items.
• Light items (plastic bowls etc.) must be loaded in the upper basket and arranged so
they do not move.
13
For washing in the dishwasher the following cutlery and dishes
are not suitable:
are of limited suitability:
• Cutlery with wooden, horn, china or mother-of• Only wash stoneware in the dishwasher if it is
pearls handles.
specially marked as being dishwasher-safe by the
manufacturer.
• Plastic items that are not heat resistant.
•
Glazed
patterns may fade if machine washed
• Older cutlery with glued parts that are not temperafrequently.
ture resistant.
• Silver and aluminium parts have a tendency to dis• Bonded cutlery items or dishes.
colour during washing: Residues, e.g. egg white,
• Pewter or copper items.
egg yolk and mustard often cause discolouring and
• Lead crystal glass.
staining on silver. Therefore always clean left-overs
• Steel items prone to rusting.
from silver immediately, if it is not to be washed
• Wooden platters.
straight after use.
• Items made from synthetics fibres.
Load cutlery. For best results we recommend you
to use the cutlery grid provided (if the size and dimensions of the cutlery
allow it)
14
Place knives and other
Load the lower basket. Arrange serving dishes and
items of cutlery with sharp large lids around the edge of the basket.
points or edges with their
handles facing upwards.
Risk of injury!
The two rows of prongs on
the lower basket can be
easily lowered to allow
you to load pots, pans and
bowls.
Load upper basket. Light
items (plastic bowls etc.)
must be loaded in the upper basket and arranged
so they do not move.
For taller items, the cup
racks can be folded upwards.
If plates are to be loaded in the upper basket: load
them starting from the rear positions; tilting them
slightly forwards and avoiding the front positions near
the door.
Adjusting the height of the
upper basket
If washing very large plates you can load them
in the lower basket after moving the upper basket to the higher position.
Maximum height of the dishes in :
upper basket
lower basket
With upper basket raised
20 cm
31 cm
With upper basket lowered
24 cm
27 cm
15
To move to the higher position proceed as follows:
1. Pull out the basket until it stops.
2. Carefully lift both sides upwards until the mechanism is engaged and the basket is stable.
To lower the basket to the original position proceed
as follows:
1. Pull out the basket until it stops.
2. Carefully lift both sides upwards and then allow the
mechanism to drop back down slowly, keeping
hold of it.
IMPORTANT!
Never lift or lower the basket on one side only
IMPORTANT!
When the basket is in the higher position you
will not be able to use the cup racks.
Use of detergent
IMPORTANT!
Only use detergents suitable for dishwashers.
Open the lid.
16
Observe the manufacturer’s dosing and storage recommendations.
Fill in the detergent in
compartment A.
Observe the dosing levels.
For programmes with pre- When using detergent
Close the lid.
wash add an additional
tablets: place detergent
detergent dose in comtablets in compartment A.
partmentB.
"3 in 1 function"
This appliance is equipped with the "3 in 1 function", that allows the use of the "3 in 1" combi
detergent tablets.
These products are detergents with a combined
cleaning, rinsing and salt functions. They can
also contain other different agents depending
on which kind of tablets you choose ("3 in 1",
"4 in 1", "5 in 1" etc...)
Check whether these detergents are suitable
for your water hardness. See the manufacturers instructions.
Once this function is selected it will remain active also for the following washing programmes.
With the selection of this function the inflow of
rinse aid and salt from each respective supply
container is automatically deactivated and also
the indicator lights for salt and rinse aid are deactivated.
Select the "3 in 1 function" before the start of a
washing programme.
With the use of the "3 in 1 function", the cycle
durations may change.
Once the programme is running, the "3 in 1
function" can NO longer be changed.
If you want to exclude the "3 in 1 function" you
have to cancel the programme setting and then
deactivate the "3 in 1 function". In this case you
have to set a washing programme (and desired
options) again.
Activation/deactivation of the 3 in 1 function
Press simultaneously the two buttons positioned over the writing 3 in 1, until the "3 in 1
17
function "indicator light illuminates. This means
that the function is active.
To deactivate the function press the same buttons again until the indicator light corresponding to the "3 in 1" symbol turns off.
IMPORTANT!
If the drying results are not satisfactory we suggest that you:
1.
2.
3.
•
Fill up the rinse aid dispenser with rinse aid.
Activate the rinse aid dispenser.
Set the rinse aid dosage to position 2.
The activation/deactivation of the rinse aid
dispenser can only be possible with the "3 in
1 function" active.
Activation/deactivation of the
rinse aid dispenser
1. Press the On/Off button. The dishwasher
must be in setting mode.
2. Press simultaneously buttons B and C, until the indicator lights of buttons A, B, and
C start flashing.
3. Press button B, the indicator lights of buttons A and C turn off while the indicator
light of button B goes on flashing.
4. To activate the rinse aid dispenser, press
button B again, the end of programme indicator light illuminates, indicating that the
rinse aid dispenser has been activated.
5. To memorise the operation, switch off the
dishwasher by pressing the On/Off button.
6. To deactivate the rinse aid dispenser
again, follow the above instructions until
the end of programme indicator light turns
off.
IMPORTANT!
If you decide to turn back to the use of standard
detergent system we advise that you:
1. Deactivate the 3 in 1 function.
2. Fill up the salt container and the rinse aid
dispenser again.
3. Adjust the water hardness setting to the
highest setting and perform 1 normal washing programme without loading any dishes.
4. Adjust the water hardness setting according to the hardness of the water in your
area.
5. Adjust the rinse aid dosage.
Unloading the dishwasher
• Hot dishes are sensitive to knocks.
The dishes should therefore be allowed to
cool down before removing from the appliance.
• Empty the lower basket first and then the
upper one; this will avoid water dripping from
the upper basket onto the dishes in the lower
one.
18
• Water may appear on the sides and the door
of the dishwasher as the stainless steel will
eventually become cooler than the dishes.
CAUTION!
When the washing programme has finished, it
is recommended that the dishwasher is unplugged and the water tap turned off.
Care and cleaning
Cleaning the filters
IMPORTANT!
NEVER use the dishwasher without filters. Incorrect repositioning and fitting of the filters will
produce poor washing results.
Clean filters A, B and C Turn the handle about 1/4 Remove filter A from the
thoroughly under running turn anticlockwise and re- base of the washing comwater.
move filters B and C.
partment.
Put the flat filter A back in Replace the filters and
the base of the washing lock by turning the handle
compartment and ensure clockwise to the stop.
that it fits perfectly under
the two guidesD.
Cleaning the spray arms
External cleaning
NEVER try to remove the spray arms.
Clean the external surfaces of the machine and
control panel with a damp soft cloth. If
necessary use only neutral detergents. Never
If residues of soil have clogged the holes in the
spray arms, remove them with a cocktail stick.
19
use abrasive products, scouring pads or solvent (acetone, trichloroethylene etc....).
Internal cleaning
Ensure that the seals around the door, the detergent and rinse aid dispensers are cleaned
regularly with a damp cloth.
We recommend every 3 months to run the wash
programme for heavy soiled dishes using detergent but without dishes.
Prolonged periods of nonoperation
If you are not using the machine for any prolonged period of time you are advised to:
1. Unplug the appliance and then turn off the
water.
2. Leave the door ajar to prevent the formation of any unpleasant smells.
3. Leave the inside of the machine clean.
Frost precautions
Avoid placing the machine in a location where
the temperature is below 0°C. If this is
unavoidable, empty the machine, close the appliance door, disconnect the water inlet pipe
and empty it.
Moving the machine
If you have to move the machine (moving house
etc....):
1. Unplug it.
2. Turn the water tap off.
3. Remove the water inlet and discharge hoses.
4. Pull the machine out together with the hoses.
Avoid over tilting the machine during transportation.
Environmental concerns
Packaging material
The packaging materials are environmentally
friendly and can be recycled. The plastic components are identified by markings, e.g. >PE<,
>PS<, etc. Please dispose of the packaging
materials in the appropriate container at the
community waste disposal facilities.
CAUTION!
When a unit is no longer being used:
• Pull the plug out of the socket.
• Cut off the cable and plug and dispose of
them.
20
• Dispose of the door catch. This prevents
children from trapping themselves inside
and endangering their lives.
The symbol on the product or on its packaging
indicates that this product may not be treated
as household waste. Instead it should be taken
to the appropriate collection point for the recycling of electrical and electronic equipment. By
ensuring this product is disposed of correctly,
you will help prevent potential negative consequences for the environment and human
health, which could otherwise be caused by inappropriate waste handling of this product. For
more detailed information about recycling of
this product, please contact your local council,
your household waste disposal service or the
shop where you purchased the product.
Something not working
The dishwasher will not start or stops during
operation. Certain problems are due to the lack
of simple maintenance or oversights, which can
be solved with the help of the indications described in the chart, without calling out an
engineer.
Switch off the dishwasher, open the door and
carry out the following suggested corrective actions.
Fault code and malfunction
Possible cause and solution
The dishwasher does not fill with water.
• continuous flashing of the light of the running
programme
• 1 flash of the "End of programme" light
• The water tap is blocked or furred with limescale.
Clean the water tap.
• The water tap is turned off.
Turn the water tap on.
• The filter (where present) in the threaded hose fitting
at the water inlet valve is blocked.
Clean the filter in the threaded hose fitting.
• The water inlet hose has not been correctly laid or
it is bent or squashed.
Check the water inlet hose connection.
The dishwasher will not drain.
• continuous flashing of the light of the running
programme
• 2 flashes of the "End of programme" light
• The sink spigot is blocked.
Clean out the sink spigot.
• The water drain hose has not been correctly laid or
it is bent or squashed.
Check the water drain hose connection.
• continuous flashing of the light of the running • Anti-flood device is activated
Close the water tap and contact your local Service
programme
Force Centre.
• 3 flashes of the end of programme indicator light
• The programme does not start.
• The dishwasher door has not been properly closed.
Close the door.
• The main plug is not plugged in.
Insert the mains plug.
• The fuse has blown in the household fuse box.
Replace the fuse.
21
Once these checks have been carried out;
close the dishwasher’s door and switch on the
appliance. Press the button of the programme
that was running before the intervention of the
alarm. The programme will continue from the
point at which it was interrupted.
If the malfunction or fault code reappears contact the Service Force Centre.
For other fault codes not described in the above
chart, please contact your Service Force Centre.
Contact your local Service Force Centre, quoting the model (Mod.), product number (PNC)
and serial number (S.N.).
This information can be found on the rating
plate located on the side of the dishwasher
door.
So that you always have these numbers at
hand, we recommend you to make a note of
them here:
Mod. : . . . . . . . . . . . . . . . . . . . . . . .
PNC :. . . . . . . . . . . . . . . . . . . . . . . .
S.N. : . . . . . . . . . . . . . . . . . . . . . . . .
The wash results are not satisfactory
The dishes are not clean
• The wrong washing programme has been selected.
• The dishes are arranged in such a way as to stop
water reaching all parts of the surface. The baskets
must not be overloaded.
• The spray arms do not rotate freely due to incorrect
arrangement of the load.
• The filters in the base of the washing compartment
are dirty or incorrectly positioned.
• Too little or no detergent has been used.
• Where there are limescales deposits on the dishes;
the salt container is empty or the incorrect level of
the water softener has been set.
• The drain hose connection is not correct.
• The salt container cap is not properly closed.
The dishes are wet and dull
• Rinse aid was not used.
• The rinse aid dispenser is empty.
There are streaks, milky spots or a bluish coating on
glasses and dishes
• Decrease rinse aid dosing.
Water drops have dries onto glasses and dishes
• Increase rinse aid dosing.
• The detergent may be the cause. Contact the detergent manufacturer’s consumer care line.
If after all these checks, the problem persists,
contact your local Service Force Centre.
22
Technical data
Dimensions
Width x Height x Depth (cm)
Electrical connection
Voltage - Overall power - Fuse
Information on the electrical connection is given on the rating plate on the
inner edge of the dishwasher’s door.
60,0 x 85,0 x 61,0
Water supply pressure
Minimum - Maximum
(MPa)
0,05 - 0,8
Capacity
place settings
12
Max. weight
kg
40,5
Noise level
dB(A)
49
Consumption values
iations of the power supply and the amount of
dishes.
The consumption values are intended as a
guide and depends on the pressure and the
temperature of the water and also by the var-
Consumption values
Programme
Programme duration (in Energy consumption (in
minutes)
kWh)
Water (litres)
Intensive 70°
80-90
1,6-1,8
22-24
Normal 65°
95-105
1,5-1,7
21-23
Eat-Load-Run
30
0,9
9
BIO 50° (Test programme for Test Institutes)
170
1,05
14
Rinse and Hold
12
0,1
4
Hints for test institutes
Testing in accordance with EN 60704 must be
carried out with appliance fully loaded and us-
ing the test programme (see "Consumption
values").
23
Test in accordance with EN 50242 must be
carried out when the salt container and rinse
aid dispenser have been filled with salt and
rinse aid respectively and using the test programme (see "Consumption values").
Full load: 12 standard place settings
Amount of detergent required
5 g + 25 g (Type B)
Rinse aid setting
position 4 (Type III)
Upper basket
Cutlery basket
Lower basket
cup racks: position A
Installation
WARNING!
Any electrical and/or plumbing work required to
install this appliance should be carried out by a
qualified electrician and/or plumber or competent person.
24
Water connection
WARNING!
The dishwasher must not be connected to open
water appliances or instantaneous water heaters. This dishwasher may be fed with either hot
(max. 60°) or cold water. Nevertheless we advise you a cold water supply.
WARNING!
Only use, for connection to the water mains,
new hose-set; old hose-set must not be reused.
you should run the water for a few minutes before connecting the inlet hose.
CAUTION!
If the machine is connected to new pipes or
pipes which have not been used for a long time,
Inlet hose
Connect the inlet hose to a water tap with an external
thread of 3/4”.
The inlet hose can be turned either to the left or the
right to suit the installation by means of the locknut.
The locknut must be correctly fitted to avoid water
leaks.
Drain hose
Connect drain hose to the Required height: 30 to 100 Ensure that the hoses are When connecting the
sink. Secure it with the
cm above bottom of the
not kinked, crushed or en- drain hose to an under
supplied hose clamp.
dishwasher.
tangled.
sink trap spigot, the entire
plastic membrane (A)
must be removed. Failure to remove all the membrane will result in food
particles building up over
time eventually blocking
the dishwasher drain hose
spigot.
25
If you use a drain hose extension the total
length should not be longer than 4 metres.
Likewise the internal diameter of the couplings
used for connections to the waste outlet must
be no smaller than the diameter of the hose
provided.
Electrical connection
CAUTION!
Safety standards require the appliance to be
earthed.
Prior to using the appliance for the first time,
ensure that the rated voltage and type of supply
on the rating plate match that of the supply
where the appliance is to be installed.
The fuse rating is also to be found on the rating
plate.
Always plug the mains plug into a correctly installed shockproof socket. Multi-way plugs,
connectors and extension cables must not be
used.
26
This could constitute a fire hazard through overheating.
If necessary, have the domestic wiring system
socket replaced. In case that the electrical cable has to be replaced, contact your local Service Force centre.
The plug must be accessible after the appliance
has been installed.
Never unplug the appliance by pulling on the
cable. Always pull the plug.
The manufacturer accepts no liability for failure
to observe the above safety precautions.
Fitting under a counter
By removing the dishwasher’s worktop, you can
install it under a close fitting sink unit or a preexisting top.
Be sure that once the appliance has been installed, it is easily accessible for the service
engineer in the event that a repair is required.
Levelling
Good levelling is essential for correct closure and
sealing of the door.
When the appliance is correctly levelled, the door will
not catch on either side of the cabinet.
Guarantee/Customer Service
Belgium
DECLARATION OF GUARANTEE TERMS.
Our appliances are produced with the greatest
of care. However, a defect may still occur. Our
consumer services department will repair this
upon request, either during or after the guarantee period. The service life of the appliance
will not, however, be reduced as a result.
This declaration of guarantee terms is based
on European Union Directive 99/44/EC and the
provisions of the Civil Code. The statutory rights
that the consumer has under this legislation are
not affected by this declaration of guarantee
terms.
This declaration does not affect the vendor's
statutory warranty to the end user. The appliance is guaranteed within the context of and in
adherence with the following terms:
1. In accordance with provisions laid down in
paragraphs 2 to 15, we will remedy free of
charge any defect that occurs within 24
months from the date the appliance is delivered to the first end user. These guarantee terms do not apply in the event of
2.
3.
4.
5.
6.
use for professional or equivalent purposes.
Performing the guarantee means that the
appliance is returned to the condition it
was in before the defect occurred. Defective parts are replaced or repaired. Parts
replaced free of charge become our
property.
So as to avoid more severe damage, the
defect must be brought to our attention
immediately.
Applying the guarantee is subject to the
consumer providing proof of purchase
showing the purchase and/or delivery
date.
The guarantee will not apply if damage
caused to delicate parts, such as glass
(vitreous ceramic), synthetic materials
and rubber, is the result of inappropriate
use.
The guarantee cannot be called on for minor faults that do not affect the value or the
overall reliability of the appliance.
27
7.
The statutory warranty does not apply
when defects are caused by:
– a chemical or electrochemical reaction
caused by water,
– abnormal environmental conditions in
general,
– unsuitable operating conditions,
– contact with harsh substances.
8. The guarantee does not apply to defects
due to transport which have occurred outside of our responsibility. Nor will the guarantee cover those caused by inadequate
installation or assembly, lack of maintenance or failure to respect the assembly
instructions or directions for use.
9. Defects that result from repairs or measures carried out by people who are not
qualified or expert or defects that result
from the addition of non-original accessories or spare parts are not covered by the
guarantee.
10. Appliances that are easy to transport may
be delivered or sent to the consumer services department. Home repairs are only
anticipated for bulky appliances or built-in
appliances.
11. If the appliances are built-in, built-under,
fixed or suspended in such a way that removing and replacing them in the place
where they are fitted takes more than half
an hour, the costs that result there from
will be charged for. Connected damage
caused by these removal and replacement operations will be the responsibility
of the user.
12. If, during the guarantee period, repairing
the same defect repeatedly is not conclusive, or if the repair costs are considered
28
disproportionate, in agreement with the
consumer, the defective appliance may be
replaced with another appliance of the
same value. In this event, we reserve the
right to ask for a financial contribution calculated according to the length of time it
has been used.
13. A repair under guarantee does not mean
that the normal guarantee period will be
extended nor that a new guarantee period
begins.
14. We give a twelve month guarantee for repairs, limited to the same defect.
15. Except in the event where liability is legally
imposed, this declaration of guarantee
terms excludes any compensation for
damage outside the appliance for which
the consumer wishes to assert his rights.
In the event of legally admitted liability,
compensation will not exceed the purchase price paid for the appliance.
These guarantee terms are only valid for appliances purchased and used in Belgium. For
exported appliances, the user must first make
sure that they satisfy the technical conditions
(e.g.: voltage, frequency, installation instructions, type of gas, etc.) for the country concerned and that they can withstand the local
climatic and environmental conditions. For appliances purchased abroad, the user must first
ensure that they meet the qualifications required in Belgium. Non-essential or requested
adjustments are not covered by the guarantee
and are not possible in all cases.
Our consumer services department is always
at your disposal, even after the guarantee
period has expired.
Address for our consumer services department:
Belgium
Electrolux Home Products Consumer services
Belgium ELECTROLUX
SERVICE Bergensesteenweg 719 1502 Lembeek
Tel.:
Fax.:
02/363.04.44
02/363.04.00
02/363.04.60
Tel.:
Fax.:
00 352 42 431-1
00 352 42 431-360
E-mail: consumer.services@electrolux.be
Luxembourg
Grand-Duché de Luxembourg ELECTROLUX
HOME PRODUCTS Rue
de Bitbourg. 7 L-1273
Luxembourg-Hamm
Consumer services
E-mail: consumer-service.luxembourg@electrolux.lu
European Guarantee
This appliance is guaranteed by Electrolux in
each of the countries listed at the back of this
user manual, for the period specified in the appliance guarantee or otherwise by law. If you
move from one of these countries to another of
the countries listed, the appliance guarantee
will move with you subject to the following qualifications:• The appliance guarantee starts from the
date you first purchased the appliance which
will be evidenced by production of a valid
purchase document issued by the seller of
the appliance.
• The appliance guarantee is for the same
period and to the same extent for labour and
parts as exists in your new country of resi-
dence for this particular model or range of
appliances.
• The appliance guarantee is personal to the
original purchaser of the appliance and cannot be transferred to another user.
• The appliance is installed and used in accordance with instructions issued by Electrolux and is only used within the home, i.e.
is not used for commercial purposes.
• The appliance is installed in accordance with
all relevant regulations in force within your
new country of residence.
The provisions of this European Guarantee do
not affect any of the rights granted to you by
law.
29
www.electrolux.com
Albania
+35 5 4 261 450
Rr. Pjeter Bogdani Nr. 7 Tirane
Belgique/België/Belgien
+32 2 363 04 44
Bergensesteenweg 719, 1502
Lembeek
Česká republika
+420 2 61 12 61 12
Budějovická 3, Praha 4, 140 21
Danmark
+45 70 11 74 00
Sjællandsgade 2, 7000 Fredericia
Deutschland
+49 180 32 26 622
Muggenhofer Str. 135, 90429 Nürnberg
Eesti
+37 2 66 50 030
Pärnu mnt. 153, 11624 Tallinn
España
+34 902 11 63 88
Carretera M-300, Km. 29,900
Alcalá de Henares Madrid
France
www.electrolux.fr
Great Britain
+44 8705 929 929
Addington Way, Luton, Bedfordshire LU4 9QQ
Hellas
+30 23 10 56 19 70
4, Limnou Str., 54627 Thessaloniki
Hrvatska
+385 1 63 23 338
Slavonska avenija 3, 10000 Zagreb
Ireland
+353 1 40 90 753
Long Mile Road Dublin 12
Italia
+39 (0) 434 558500
C.so Lino Zanussi, 26 - 33080 Porcia (PN)
Latvija
+37 17 84 59 34
Kr. Barona iela 130/2, LV-1012,
Riga
Lietuva
+370 5 278 06 03
Ozo 10a, LT-08200 Vilnius
Luxembourg
+352 42 431 301
Rue de Bitbourg, 7, L-1273 Hamm
Magyarország
+36 1 252 1773
H-1142 Budapest XIV, Erzsébet
királyné útja 87
Nederland
+31 17 24 68 300
Vennootsweg 1, 2404 CG - Alphen
aan den Rijn
Norge
+47 81 5 30 222
Risløkkvn. 2 , 0508 Oslo
Österreich
+43 18 66 400
Herziggasse 9, 1230 Wien
Polska
+48 22 43 47 300
ul. Kolejowa 5/7, Warszawa
30
Portugal
+35 12 14 40 39 39
Quinta da Fonte - Edificio Gonçalves Zarco - Q 35 -2774-518
Paço de Arcos
Romania
+40 21 451 20 30
Str. Garii Progresului 2, S4, 040671
RO
Schweiz - Suisse - Svizzera
+41 62 88 99 111
Industriestrasse 10, CH-5506 Mägenwil
Slovenija
+38 61 24 25 731
Gerbičeva ulica 98, 1000 Ljubljana
Slovensko
+421 2 43 33 43 22
Electrolux Slovakia s.r.o., Electrolux Domáce spotrebiče SK,
Seberíniho 1, 821 03 Bratislava
Suomi
www.electrolux.fi
Sverige
+46 (0)771 76 76 76
Electrolux Service, S:t Göransgatan 143, S-105 45 Stockholm
Türkiye
+90 21 22 93 10 25
Tarlabaşı caddesi no : 35 Taksim
İstanbul
Россия
+7 495 937 7837
129090 Москва, Олимпийский
проспект, 16, БЦ "Олимпик"
31
www.electrolux.com
156996960-00-31052007
Subject to change without notice