Avers Electric projection screen User`s manual

BETA - 2 device control system
trigered by projector power
consumption
User’s manual
Read these instructions carefully before operating the screen.
Dear Customer,
Thank you very much for the purchase of our product. The manual booklet contains all operation information
you may require to install properly and operate the radio remote control system. We hope it will help you to get the most
enjoyment of your new control system. Enjoy time with the Avers Screens product.
SAFETY INFORMATION
NOTICE: Important safety information.
Follow the instructions described in the operating manual for safety reasons. After reading the manual, please store
it in a safe place just in case you need it in the future.
NOTICE: THE DEVICE HAVE TO BE EARTHED.
WARNING:
1) Disconnect the device from the power supply if it will not be used within longer period of time.
2) Do not open the casing of the device in order to avoid possible electric shock. There are not any user operated
parts inside the case of the screen. All service work can be done by Avers Authorized Service Center personnel
only.
Table of contents:
1. Safety rules
1.1. Declaration of Conformity CE
2. Product specification
2.1. Contents of package
2.2. Technical data
3. Control system installation
3.1 Installation directions
3.2 Control unit installation
3.3 Electric installation
3.4 Control system programming
4. Control system operation
4.1 Automatic operation
4.1 Manual operation
4.2 Control system maintenance
4.3 Before asking for service
5. Warranty conditions
1. SAFETY RULES
SAFETY INFORMATION
NOTICE: Important safety information. It is important for the safety of persons to follow these instructions.
After reading the manual, please save it just in case of need in the future.
Ÿ
Do not allow children to play with the remote control transmitter or fixed manual switch connected to the control system.
Ÿ
Keep the remote control transmitter out of reach of children.
2
Ÿ
Frequently examine the control system installation for imbalance and signs of wear or damage to cables. Do not use if
repair or adjustment is necessary.
Ÿ
Watch the moving screen and keep the people away until the screen is completely rolled in/out. It will help to avoid
injuries caused with moving screen.
Ÿ
All installation work should be carried out by the qualified technician.
Ÿ
Improper installation can cause device damage or health breakdown.
Ÿ
Do not do anything that may damage the power cables.
Ÿ
Operation of the control system with damaged power cords can result with electric shock, electric short circuit and fire.
Ÿ
Do not touch the power cables and the control unit with wet hands.
Ÿ
Do not allow nor Control Unit nor Trigger Transmitter to flood with water, it can result with electric shock, electric short
circuit and fire.
Ÿ
Do not apply any metallic objects into the Trigger Transmitter though the venting holes, it can result with electric shock,
electric short circuit and control system damage.
Ÿ
Always follow the instructions described in the operating manual.
1.1 Declaration of Conformity CE
Manufacturer’s Declaration of ConformityCE
AVERS Screens Sp. z o.o.
Under it’s own responsibility declares:
All screensand accessories mentioned below are manufactured in Polandaccording to the essential safety
requirements of Council Directive 98/79/WE
Control systems: ALFA TRIGGER, WIRELESS ALFA TRIGGER
ALFA IR, ALFA RADIO, BETA, DELTA
The above mentioned products are in conformity with the European Directives
and especially with the norms:
PN-EN 55014-1:2007(U)
PN-EN 50082-1:1997
PN-EN 60335-1:2004
PN-EN 61000-3-2:2007
PN-EN 61000-3-3:1997
IEC 60335-2-97:2007
2. Product specification
BETA control system is dedicated to control Avers electric projection screens, projector lifts Avers Prolift, electric
courtain systems Avers Virgo and other electric appliances controlled by applying power supply to control terminals. The
control system was designed for fixed installation at projection systems for business presentations and/or home cinema
applications. Electric devices connected to BETA system are controlled automatically based on the attached projector
power consumption analysis. In case of projector malfunction manual control is possible as an option. The Control Unit
can be used in slave mode as controller with external control systems (intelligent building installations). BETA control
system is equipped with accessories allowing to transmit IR control signals send from the projectors remote transmitter to
the projector installed behind an IR barrier (like ceiling, wall, etc). This feature sloves common problem to control remotely
projector installed at the projector lift.
3
2.1 Contents of packaging
Please, check carefully if any physical damage of the control system has not happen during transportation.
Inspect the package for all accessories presented below:
x2
x1
Control unit x 1
Wall plug converter x 1
IR accessories
Operation manual x 1
2.2 Technical Data
Control Unit:
IR Transmitter/Receiver:
Dimensions: 153 x 108 x 58 mm
Dimensions: Ø13 x 40mm
(2 x 13x8x5mm)
Supply voltage: 220-240V, AC 50Hz
Connection cable length: 145cm
Control votage: 220-240V, AC 50Hz
Max. control current: 1,5A
Programmable power consumption level triggering the control unit
Front veiw
Side view
1
2
3
4
1 - Triggering projector power outlet
2 - Cable holders
3 - IR receiver socket (white)
4 - IR transmitter socket (black)
Picture 1 Control Unit
3. Control system installation
3.1. Installation precautions
- Installation work should be carried out by a qualified technician in accordance with the instructions described below.
- Fixed installation of the control system should be done with use of the screws and anchors suitable for the walls/ceilings
materials at the installation place and the genuine installation brackets delivered with the screen.
3.2. Control unit installation
- Appoint the location of the control unit fixing points (see Appendix).
- Drill holes for the fixing anchors.
- Un tight 2 plastic screws and remove the front cover of Control Unit.
- Fix the control unit with anchors.
4
3.3 Electric installation
- Lead out the power cables to the place of Control Unit installation.
- Control Unit power line should be fused with 3,15A fuse.
- Switch off the screen power line during installation work.
- Manual wall steering switch should be installed at the place meeting the following conditions:
a) installation150-180cm above the floor level,
b) the screen should be visible by the wall switch operator during the screen operation,
c) wall switch operator cannot stay in reach of any of the screen’s moving parts during the screen operation.
- Connect screen cable to the control terminal as shown at the Picture 3.
- Optionally connect external control system or manual wall switch to the manual control terminal as shown at the Picture 3.
- Connect power supply cable to the power supply terminal as shown at the Picture 3.
- Apply front cover of and fix it with plastic screws.
- Apply projector power cord wall plug to the power outlet located at the trigger signal transmitter
- Connect Trigger Transmitter to the wall outlet you plan to connect projector power cord.
ATTENTION: Electric installation work should be carried out by a certified electrician.
Inside view (front cover removed)
2
1
3
Connect projector
power cable, use
converter, when
required
4
y-g
y-g
br
bl
bk
7
br
bl
bk
5
Screen/Lift 2
Screen/Lift 1
br
y-g
bl
6
IR Receiver
IR Transmitter
Live
1 - IR activity indicator (blinks when active)
2 - P1 programming button
3 - Power indicator (lights red when power
is connected)
4 - LED1programming indicator
5 - Fuse
6 - Connecting Terimnals
7 - Projector power outlet
0
~
Optional
manual
control switch
connection
Screen/Lift cable
bl - blue (common)
br - brown (rolling up)
yg - yellow-green (protective)
bk - black (rolling down)
Power cable
L1 - brown (live)
N - blue (neutral)
G - yellow-green (protective)
Picture 2 BETA Control Unit electric installation
!!! NOTICE !!!
Do not connect any any electric devices except multimedia projector to the power outlet located at the
control unit. Maximum projector power consumption 600W.
3.4 Control system programming
Just after first installation of the control system and each time the projector is replaced with an other unit BETA control
system must be programmed. Projector power consumption level required to trigger the control system must be recognized
and memorized to provide reliable system operation:
a) Attach all devices to the BETA control unit (see Picture 2).
b) Apply power to the BETA control unit (Power indicator will light continuous red)
c) Press P1 programm button (LED1 indicator will light continuous green)
5
d) Switch on the projector with “Power ON” button located at the projector body or it’s remote transmiter.
e) LED1 indicator will blink 3 times and douse to confirm the power consumption level was recognized and
memorized.
!!!CAUTION!!!
Programming procedure must be performed each time attached projector is replaced with an other unit/model
Beta control system is ready for usa as soon as the programming procedure is finished.
4. Control system operation
Avers BETA control system provides automatic and/or manual control of 2 electric devices for example Avers projection
screen (models without integrated control system) and Avers Prolift projector lift.
4.1 Automatic operation
- Press “POWER” button at the projector’s remote control transmitter or at the projector itself, projector lamp will lighton. BETA control system will switch on motors of connected devices (i.e. projection screen and projector lift).
Motors will stop automatically as soon as the bottom stop points will be reached.
- Press “POWER” button at the projector’s remote control transmitter or at the projector itself, projector lamp will light
off. BETA control system will switch on motors of connected devices (i.e. projection screen and projector lift). Motors
will stop automatically as soon as the upper stop points will be reached.
4.2 Manual operation
Manual control of devices conected to the BETA control system is possible with the optional wall control switch (original
screen/lift wall control switch) connected to the dedicated termina.
- Push button “‚ ”, BETA control system will switch on motors of connected devices (i.e. projection screen and
projector lift). Motors will stop automatically as soon as the bottom stop points will be reached.
- Push button “
”, BETA control system will switch on motors of connected devices (i.e. projection screen and
projector lift). Motors will stop automatically as soon as the upper stop points will be reached.
4.2 Control system maintenance
BETA control system do not require periodical service maintenance. Clean dust from the control unit case with dry soft
cloths. If needed use moisturized cloth with soft detergent to remove stains. After stain removal dry the cleaned surface
with cloth carefully.
4.3 Before calling the service
Symptoms
Reasons
Remedy
Control system do not react to Projector power cord is not plugged into the Plug in projector power cable to the BETA
projector “Power On” action
BETA power outlet.
power outlet.
Power consumption from the outlet at the
Trigger Transmitter is too low.
At other cases please contact service.
Re-programm BETA control system with the
projector.
5. Warranty conditions
1) Avers control system warranty period is 24 months from the date of purchase confirmed with the original purchase
invoice.
3) Surety commits to fix free of charge any failures (component or production defects) of the product which appear during
warranty period.
4) Warranty exclusions :
a) the failures caused by the usage of the control system against the rules described in operation manual,
b) the failures caused by improper storage or transportation,
c) mechanical defects of the control system other than mentioned at point 3),
d) damages caused with overvoltage at power network,
e) deinstallation and reinstallation of the screen.
5) Avers Screens Service department will remove all defects within 21 days after receiving the demaged product.
6) Warranty claims should be passed to the screen supplier (dealer).
140,00
!!! CAUTION !!! Check the holes printed at the template match the location of fixing points at the control unit
before you use it.
76,00
Manufactured after 13.08.2005
This symbol on the products and/or accompanying documents means that used electrical and
electronic products should not be mixed with general household waste. Disposing of this
product correctly will help to save valuable resources and prevent any potentialnegative effects
on human health and the environment which could otherwise arise from inappropriate waste
handling. Please contact your local authority for further details of your nearest designated
collection point.
Wersja
20.05.2012