AIMB-766 Socket LGA 775 Intel® CoreTM 2 Quad / Core 2 Duo

AIMB-766 Socket LGA 775 Intel® CoreTM 2 Quad /
Core 2 Duo / Intel Pentium Dual Core / Celeron FSB
1333 MHz Processor-based ATX Motherboard with
PCIe, DDR2, and Dual GbE
Startup Manual
Specifications
Packing List
Before you begin installing your card, please make sure that
the following items have been shipped:
• AIMB-766 Socket LGA 775 Intel® Core 2 Quad / Core 2
Duo / Intel Pentium Dual Core / Celeron FSB 1333 MHz
Processor-based ATX Motherboard with PCIe, DDR2, and
Dual GbE
• 1 AIMB-766 Startup Manual
• 1 Driver CD (user’s manual is included)
• 1 FDD cable
• 1 Ultra ATA 66/100 HDD cable
• 2 Serial ATA HDD data cables
• 2 Serial ATA HDD power cables
• 2 COM Port cables (2 to 2,1 to 1)
• 1 I/O port bracket
• 1 jumper package
• 1 warranty card
TM
If any of these items are missing or damaged, please contact your distributor or sales representative immediately.
Note: Acrobat Reader is required to view any PDF
file.Acrobat Reader can be downloaded at:
www.adobe.com/Products/acrobat/readstep2.
html (Acrobat is a trademark of Adobe)
Standard SBC Functions
• CPU: LGA775 Intel Core 2 Quad/Core 2 Due/Pentium
Dual Core/Celeron
• BIOS: AMI 32 Mb SPI BIOS
• FSB: 800/1066/1333 MHz
• Chipset: Q35 with ICH9DO
• System memory: Up to 8 GB four 240-pin DIMM sockets.
Supports dual channel DDR2 800/1066/1333 SDRAM.
Note: Due to the inherent limitations of PC architecture, the
system may not fully detect 8 GB RAM when 8
GB RAM is installed.
• SATA2 Interface: Six on-board serial ATA2 connectors
with a data transmission rate of up to 300 MB/s supporting Advanced Host Controller Interface (AHCI) technology.
VG version only support four on board serial ATA2.
• IDE Interface: Supports PIO mode 4 (16.67 MB/s data
transfer rate) and ATA 33/66/100 (33/66/100 MB/s data
transfer rate) BIOS enabled/disabled.
• FDD interface: Supports one FDD
• Serial ports: Four serial ports, COM1,COM3 and COM4
are RS-232; COM2 is RS-232/422/485
• Parallel port: One parallel port, supports SPP/EPP/ECP
mode
• Keyboard/mouse connector: Supports standard PS/2
keyboard and mouse
• Watchdog timer: 255 level timer intervals
• USB 2.0: Supports up to twelve USB 2.0 ports
VGA Interface
For more information on this and other Advantech
products, please visit our website at:
• Chipset: Chipset integrated VGA controller
• Display Memory: Dynamically shared system memory
up to 256 MB
• Resolution: Up to 2048 x 1536 @ 75 Hz refresh rate
http://www.advantech.com
Ethernet interface
http://www.advantech.com/eplatform
• Interface (Bold): 10/100/1000Base-T
• Controller: LAN1: Intel 82566DM; LAN2: Intel 82573L,
LAN2 is for G2 sku
For technical support and service, please visit our
support website at:
http://www.advantech.com/support
This manual is for the AIMB-766 series Rev. A1
Part No. 2006076610
Print in Taiwan
1st Edition,
August 2008
AIMB-766 Startup Manual Specifications
Mechanical and Enviromental
• Dimensions (L x W): 304.8 x 228.6 mm
• Power supply voltage: +3.3 V, +5 V, ±12 V, 5 Vsb
• Power requirements: Maximum: +5 V at 3.58 A, +3.3 V
at 2.86 A, +12 V at 3.52 A, +5 Vsb at 0.74 A, -12 V at 0.02
A (Intel Core 2 Quad 9300 2.5 Ghz (1333 MHz FSB), 4 x
1 GB DDR2 800 SDRAM)
• Operating temperature: 0 ~ 55° C (depending on CPU)
• Weight: 0.5 kg (weight of board)
Jumpers and Connectors
The board has a number of jumpers that allow you to configure your system to suit your application. The table below
lists the function of each of the jumpers and connectors.
Jumpers and Connectors
PSON1
AT(1-2) / ATX(2-3)
VOLT1
Voltage Display
JOBS1
Close: Enable OBS Alarm (HW monitor)
Open: Disable OBS Alarm
CPUFAN1
CPU FAN connector (4-pin)
SYSFAN1
System FAN connector (4-pin)
SYSFAN2
System FAN connector (4-pin)
LANLED1
LAN1/2 LED extension connector
AUDIO1
Audio connector
CDIN1
CD_IN Connector
FPAUD1
HD Audio Front Panel Pin Header
Connector / Jumper List
USB56
USB port 5, 6
Label
Function
USB78
USB port 7, 8
COMS1
Clear CMOS
USB910
USB port 9, 10
JWDT1
Watchdog Reset
USB1112
USB port 11,12
IDE1
Primary IDE connector (one channel)
SATA1
Serial ATA1
FDD1
FDD connector
SATA2
Serial ATA2
LPT1
Parallel port, Parallel port x 1, supports
SPP/ EPP/ECP mode
SATA3
Serial ATA3
LAN1_USB12
LAN1 / USB port 1, 2
SATA4
Serial ATA4
LAN2_USB34
LAN2 / USB port 3, 4
SATA5
Serial ATA5
VGA1
VGA connector
SATA6
Serial ATA6
ATX1
ATX 12V Auxiliary power connector
(for CPU)
EATXPWR1
ATX 24 Pin Main power connector (for
System)
COM1,
COM3,
COM4
Serial port: RS-232
COM2
Serial port: COM2; RS-232 (9-pin
connector)
SPDIF_OUT1
SPDIF Audio out pin header
JSETCOM2
COM2 RS-232/422/485 Jumper Setting
TPM_SLOT
TPM2.0 Module connector
KBMS1
PS/2 Keyboard and Mouse connector
SPI_CN1
SPI flash card pin header
KBMS2
External Keyboard connector (6-pin)
JIR1
Infrared connector
JFP3
Keyboard lock and power LED
Suspend: fast flash (ATX/AT)
System On: on (ATX/AT)
System Off: off (AT)
System Off: slow flash (ATX)
JFP2
External speaker / SATA HDD LED connector / SM Bus connector
JFP1
Power Switch / Reset connector
JCASE1
Case Open
AIMB-766 Startup Manual
Jumpers and Connectors
CMOS1: CMOS clear function
Pins
Result
1-2
Keep CMOS data*
2-3
Clear CMOS data
*: Default
Software Installation
The CD disc contains a driver installer program that will
lead you through the installation of various device drivers
needed to take full advantage of your motherboard.
The computer is supplied with a battery-powered Realtime
Clock circuit. There is a danger of explosion if battery is
incorrectly replaced. Replace only with same or equivalent
type recommended by the manufacturer. Discard used batteries according to manufacturer’s instructions.
Declaration of Conformity
Keep CMOS data
Clear CMOS data
JSETCOM2: CMO2 RS-232/422/485 Mode Selector
Users can use JSETCOM2 to select RS-232, RS-422 or
RS-485 mode for COM2. The default setting is RS-232.
This device complies with the requirements in Part 15 of
the FCC rules. Operation is subject to the following two
conditions:
1.
This device may not cause harmful interference.
2.
This device must accept any interference received,
including interference that may cause undesired operation.
JWDT1: Watchdog timer output option
Closed Pins
Result
1-2
NC
2-3
System reset*
*: Default
NC 1-2 Closed
System Reset 2-3 Cclosed
EATXPWR1: ATX, AT mode selecor
Closed Pins
Result
1-2
AT Mode
2-3
ATX Mode*
*: Default
AT Mode 1-2 closed
ATX Mode 2-3 closed
AIMB-766 Startup Manual JFP3
JFP2
JFP1
JWDT1
JOBS1
Board Layout: Jumper and Connector Locations
AIMB-766 Startup Manual