American Audio DCD-PRO300 User manual

DCD-PRO300
MKII
© American AUDIO Los Angeles, CA 90058 USA
IMPORTANT SAFETY ITEMS FOR U.S.A. &
CANADA MODEL ONLY
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD,
DO NOT EXPOSE THIS CD PLAYER TO
WATER OR MOISTURE.
CAUTION:
1. Handle the power supply cord carefully. Do not
damage or deform; it may cause electric shock
or malfunction when used. Hold plug attach
ment when removing from wall outlet. Do not
pull on the cord.
NOTE:
This CD player uses a semiconductor laser. It is
recommended for use in a room at the following
temperature: 41˚F - 95˚F / 5˚C - 35˚C
CAUTION
TO PREVENT ELECTRIC SHOCK DO NOT USE THIS
(POLARIZED) PLUG WITH AN EXTENSION CORD,
RECEPTACLE OR OTHER OUTLET UNLESS THE
BLADES CAN BE CAREFULLY INSERTED TO PREVENT
BLADE EXPOSURE.
2. To avoid electric shock, do not open the top
cover when the unit is plugged in. If problems
occur with the unit, call your local American
AUDIO dealer.
3. Do not place metal objects or spill liquid inside
the CD player. Electric shock or malfunction
may occur.
Please record and retain the model name and
serial number from your rating label.
Model No.______________________________
Serial No.______________________________
CAUTION
Do not open risk of electric shock
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE THE COVER RACK.
THERE ARE NO USER SERVICEABLE PARTS
INSIDE. REFER SERVICE TO YOUR
AUTHORIZED AMERICAN AUDIO DEALER.
The lightning flash with an arrow triangular
symbol is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the products enclosure, and may
be of sufficient magnitude to constitute a
risk of electric shock.
The exclamation point triangular symbol is
intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the user manual
accompanying the CD player.
FUSE
CAUTION:
USE OF CONTROLS OR ADJUSTMENTS
OTHER THAN THOSE SPECIFIED HEREIN MAY
RESULT IN HAZARDOUS RADIATION EXPOSURE.
THE COMPACT DISC PLAYER SHOULD NOT BE
ADJUSTED OR REPAIRED BY ANYONE EXCEPT
PROPERLY QUALIFIED SERVICE PERSONNEL.
NOTE:
This unit may cause interference to radio
and television reception.
Line Voltage Selection
115V
(for multiple voltage model only)
• The desired voltage may be set with 230V
the VOLTAGE SELECTOR switch
on the rear panel (using a screwdriver).
• Do not twist the VOLTAGE SELECTOR
switch with excessive force as this may
cause damage.
• If the VOLTAGE SELECTOR switch does
not move smoothly, please contact a
qualified service technician.
FUSE
VOLTAGE SELECTOR switch
American audio • DCD-PRO300™ INSTRUCTIONS MANUAL • PAGE 2
SAFETY INSTRUCTIONS
I. Read Instructions - All the safety and operating
instructions should be read before the appliance
is operated.
2. Save Instructions - The safety and operating
instructions should be saved for future
reference.
3. Heed Warnings - All warnings on the appliance
and in the operating instructions should be
adhered to.
4. Follow Instructions - All operating and user
instructions should be followed.
5. Water and Moisture - The appliance should not
be used near water - for example, near a bath
tub, washbowl, kitchen sink, laundry tub, in a
wet basement or near a swimming pool, etc.
6. Ventilation - The appliance should be situated
so that its location or position does not interfere
with its proper ventilation. For example, the
appliance should not be situated on a bed, sofa,
rug, or similar surface that may block the
ventilation openings; or, placed in a built-in
installation, such as a bookcase or cabinet that
may impede the flow of air through the
ventilation openings.
7. Heat - The appliance should be situated away
from heat sources such as radiators, heat
registers, stoves, or other appliances (including
amplifiers) that produce heat.
8. Power Sources - The appliance should be
connected to a power supply only of the type
described in the operating instructions or as
marked on the appliance.
9. Grounding or Polarization - Precautions should
be taken so that the grounding or polarization
means of an appliance is not defeated.
10. Power-Cord Protection - Power-supply cords
should be routed so that they are not likely
to be walked on or pinched by items placed
upon or against them, paying particular
attention to cords at plugs, convenience
receptacles, and the point where they exit
from the appliance.
11. Cleaning - The appliance should be cleaned
only as recommended by the manufacturer.
12. Non-use Periods - The power cord of the
appliance should be unplugged from the outlet
when left unused for a long period of time.
13. Object and Liquid Entry - Care should be taken
so that objects do not fall and liquids are not
spilled into the enclosure through openings.
14. Damage Requiring Service - The appliance
should be serviced by qualified service
personnel when:
A. The power-supply cord or the plug has
been damaged.
B. Objects have fallen, or liquid has been
spilled into the appliance.
C. The appliance has been exposed to rain
or water.
D. The appliance does not appear to operate
normally or exhibits a marked change in
performance.
E. The appliance has been dropped, or the
enclosure damaged.
15. Servicing - The user should not attempt to
service the appliance beyond that described in
the operating instructions. All other servicing
should be referred to qualified service
personnel.
American audio • DCD-PRO300™ INSTRUCTIONS MANUAL • PAGE 3
PREPARATIONS
1. Checking the Contents
Check that the carton contains the following items:
1) Main unit
2) Control unit
3) Operating instructions ( this booklet)
4) Two sets of RCA cables.
5) Two Control cords (6 feet / 1.8 meters)
2. Installing the Units
Mount the units onto your console or rack with 19" EIA rack rails.
CAUTION:
• The player will work normally when the main
unit is mounted with the front panel within
15 degrees of the vertical plane. If the unit is
tilted excessively, discs may not be loaded or
unloaded properly. (Figure 1)
• The control panel's LCDs are designed to be
clearly visible within the angles shown in
Figure 2. Mount the control unit so that the
visual angle is within this range.
Fig. 1
Fig. 2
3. Connections
1) Turn off the POWER switch.
2) Connect the RCA pin cables to the inputs on your mixer.
3) Connect the control cables to the REMOTE connector on the main unit.
CAUTION:
Be sure to use the supplied control cables. Using another type of cable may result in damage.
Be sure the power is off when connecting the control cables. Otherwise the units may not work properly.
American audio • DCD-PRO300™ INSTRUCTIONS MANUAL • PAGE 4
GENERAL NOTES ON USE
• Avoid high temperatures.
Allow for sufficient heat dispersion when installed on a rack.
• Handle the power cord carefully.
• Hold the plug when unplugging the cord.
• Keep the set free from moisture, water, and dust.
• Unplug the power cord when not using the set for long periods of time.
• Do not obstruct the ventilation holes. (For sets with ventilation holes.)
• Do not let foreign objects in the set.
• Do not let insecticides, benzene, and thinner come in contact with the set.
• Never disassemble or modify the set in any way.
MAIN FEATURES
(1) 8 times over sampling 1 bit D/A converter
(2) Beat counter
(3) Auto cue
(4) Frame search
(5) Realtime cue
(6) 4 different speed scan
(7) Pitch display
(8) 10 number buttons for direct track access
(9) 30 programmable tracks
(10) Ten cue points can be memorized
(11) Digital output RCA coaxial
(12) Fader Start , Fader Stop , (back cue) Relay playback (using the control jack)*
(13) Large brite LCD Screen can be viewed from wide angles.
(14) Transport protection
*Must have a Mixer equipped with the signal output. Look for this feature in Future American DJ Mixers.
(15) Mechanical Anti-Skip
American audio • DCD-PRO300™ INSTRUCTIONS MANUAL • PAGE 5
GENERAL FEATURES
A. REMOTE UNIT FRONT
1.
RECALL - This button allow you to cue up any of
the 10 memory points that have been memorized. Press
RECALL button then any of the 10 number buttons. the
player will cue up the selected point and pause.
8.
LCD DISPLAY - Indicates all the functions, as
they are occurring, with the CD. These functions are
explained in the next section.
9.
PITCH BEND +/- 16% (Pitch Bend Button)- When
each of the two CD players is playing a CD, the pitch
2.
MEMORY - This button allows you to program up bend function allows the positioning of the bass beats to
to 10 cue points on the CD, Press the MEMORY button be matched after the pitch of each disc is matched.
Either player can “catch up” or “fall back” to match the
during play or pause, the memory LED lights up. Use
other player. The pitch will automatically rise while the +
frame search to reach desired point, then press a
button is pressed (allowing “catch up”) and return to the
number button to memorize that starting point. Repeat
above steps to memorize all 10 starting points if desired. original pitch when the button is released. The pitch will
automatically drop while the - button is pressed (allowing
3.
NUMBER buttons (1 to 10) These buttons are
“fall back”) and return to the original pitch when the
used to select a particular track number starting point.
button is released. By changing the pitch of one disc with
They are also used in MEMORY and RECALL modes.
respect to the other in this way the beats can be matched.
4.
PROGRAM - Depress this button to stop the CD 10.
PITCH (Pitch Button)- This button activates the
an enter the program mode. Note the word “PROGRAM” Pitch Slider (14).
is indicated on the display. Select each track to be
SHUTTLE WHEEL - (OUTER RING) This wheel
programmed with the f. skip and b.skip buttons (13 & 14). 11.
has 4 forward and 4 reverse speed positions for
and press the PROGRAM button between selections.
searching through songs. The more you turn the wheel in
You can program up to 30 tracks. Press PLAY to start
either direction the faster you search through the music.
the program. To exit and erase program hold the
JOG WHEEL - (INNER RING) This jog wheel
program button down for more than 2 seconds while the 12.
unit is stopped, open the disc tray, or turn off the power. serves 2 functions depending on the mode you are
working in.
5.
REPEAT - This button allows you to select between
a. The jog wheel will act as a slow frame search
REPEAT 1
control when the CD is not playing but either paused or
REPEAT ALL CONTINULUS PLAY
set to a cue point. To set a new frame cue point, spin the
6.
SGL/CTN - You can choose between a single
wheel then press PLAY when you have determined the
track to play or all tracks in order by pressing once or
proper position. Press CUE to return to the “CUE
twice.
POINT”.
7.
OPEN/CLOSE - (Disc Tray Open/Close)- Press
to load or eject the disc. Each press will open or close
the disc tray on the transport. NOTE: Tray will not open
unless the disc has been paused.
American audio • DCD-PRO400™ INSTRUCTIONS MANUAL • PAGE 6
GENERAL FEATURES (Cont.)
24
37
25
36
26
35
27
34
28
29
30
31
13&14.TRACK (Track Buttons) - These buttons are used
to select the track to be played. FORWARD SKIP
& BACK SKIP.
15.
TIME (Time Button) - The TIME button switches
between ELAPSED PLAYING TIME,
REMAINING TIME in a selection and TOTAL
REMAINING TIME of the disc.
16.
PITCH SLIDER - The pitch can be changed up to
+/- 12% by Pressing the PITCH BUTTON so the
PITCH LED is lit, then moving the sliding fader.
The pitch will not be changed if the PITCH LED is
off.
17.
BPM BUTTON - Switches the mode of the
display between showing the BPM and the
percentage change in PITCH. Use COUNTER
BUTTON
18.
COUNTER BUTTON - Tap this button with the
beat of the music to determine the current Beats
Per Minute (BPM).
19.
REALTIME CUE – This allows you to set the CUE
POINT without stopping the play back. This button
also sets the beginning of a seamless loop.
20.
CUE - Pressing the CUE button during play
provides a return to the position at which play was
started. If PAUSE is used before CUE or CUE
POINT was set, that will become the cue point.
Alternately pressing the PLAY button and the
CUE button allows the CD to be played from the
same position any number of times. The CUE
LED will light up from the time the Cue button
is pressed until the CD has reset to the position at
which play was started. Steady lighting of this
LED indicates the ready condition.
21.
OUT / EXIT - Used to set the ending point when
looping music. The player will start to loop
continuous. Until you press this button again to
exit. This is not a seamless function.
START/PAUSE (Play/Pause Button) - Each press
of the PLAY/PAUSE BUTTON causes the
operation to change from play to pause or from
pause to play.
RELOOP BUTTON - If a LOOP has been made,
22.
23.
32
33
and you have hit the exit button, press this button
to enter the loop again. To exit loop press
OUT/EXIT button.
B. LCD
26.PLAY INDICATOR ( ) - The PLAY indicators light
during playback.
27.PAUSE INDICATOR ( ) - The PAUSE indicators
light during pause or cue mode.
28.A-B INDICATOR – These light when player
performs repeat A-B playback.
29.PROGRAM INDICATOR - This lights when
program mode is set or played.
30.REPEAT Indicator - (REPEAT 1, REPEAT ALL)
These light during repeat one or all playback.
28,31,32.TRACK, MINUTE, SECOND – These
Displays information on the current track and time.
33.PITCH OR BPM DISPLAY - Show either beat per
minute or percent of pitch adjustment.
34.BPM INDICATOR - Lights up when BPM Button is
engaged.
35.PITCH INDICATOR- Lights to show percent of
pitch is displayed.
36.ELAPSED & TOTAL REMAIN INDICATORS –
These indicate that the time shown on the display
is the ELAPSED, TOTAL remaiming or SINGLE
song remaining time.
37.LOOP, RELOOP – displayed when loop is
engaged LOOP flashes when playing loop.
D.MAIN UNIT REAR PANEL
LINE OUT 1 and 2 – The audio signals from each
player are output from these jacks.
REMOTE - Connect this connector to the control unit
using the included control cords..
DIGITAL - connect to Minidisc or CDR device.
VOLTAGE SELECTOR – (multi-vlotage models only)
On multi- voltage models, use this to select the
power voltage. Always disconnect the power plug
before changing the voltage.
E.CONTROL UNIT REAR PANEL(FIGURE 4)
CONNECT TO MAIN UNIT – Connect this connector
to the REMOTE connector on the main unit using
the included control cords.
CONTROL – Connect this connector to the control out
from mixer control out. Available on future mixers.
American audio • DCD-PRO300™ INSTRUCTIONS MANUAL • PAGE 7
BASIC OPERATIONS
1. OPENING AND CLOSING THE DISC TRAY AND LOADING DISCS
a) Opening and closing the disc tray
•
This operation only works when the power is on.
•
Press the OPEN/CLOSE button to open or close the disc tray. OPEN/CLOSE buttons are provided on
both the main unit and control unit or
•
Press PLAY button, tray automatically closes.
•
If tray is not closed after 60 seconds it will close automatically and pause.
•
The disc trays cannot be opened during playback to prevent playback from being interrupted if the
OPEN/CLOSE button is pressed accidentally. Stop playback, then press the OPEN/CLOSE button.
2. LOADING DISCS
•
Hold the disc by the edges and place it in the disc tray. Do not touch the signal surface (the glossy side).
•
When using 5 inch/12 cm discs, place the disc in the outer tray guides (Figure 8), and when using 3 inch
/8 cm discs, place them securely in the inner guides (Figure 9).
3 in. / 8cm disk
5 in. / 12cm disk
Fig.8
Fig.9
CAUTION:
• DO NOT place any foreign objects in the disc tray, and do not place more than one disc in the disc tray at a
time. Doing so may result in malfunction.
• DO NOT push the disc tray in manually when the power is off, as this may result in malfunction and
damage the player.
3. SELECTING TRACKS
• Select desired track using NUMBER Button or
• Press the TRACK Buttons once to move to one higher or lower track or
• Hold the TRACK buttons in to change tracks continuously at a higher speed.
• When a new track is selected during playback, playback begins as soon as the search operation is
completed.
4. STARTING PLAYBACK
• Press the PLAY/PAUSE button during the pause or cue to start playback.
• The PLAY indicator lights when playback starts.
• The point at which playback starts is automatically stored in the memory as the cue point. The pickup then
returns to the cue point (the point at which playback started) when the CUE button is pressed. (Back Cue)
American audio • DCD-PRO300™ INSTRUCTIONS MANUAL • PAGE 8
5. STOPPING PLAYBACK
• There are two ways to stop playback.
1) Press the PLAY/PAUSE button during playback to pause at that point.
2) Press the CUE button during playback to return to the position at which playback started(Back Cue).
6. PAUSING
• Press the PLAY/PAUSE button to switch between play and pause.
• The PAUSE indicator lights when the pause mode is set.
1) The player has completed the cue or pause operation and is waiting for the play start command.
2) When the PLAY/PAUSE button is pressed, playback starts and the cue point is stored in the memory.
3) Playing
4) The pause mode is set when the PLAY/PAUSE button is pressed again.
5) Pausing
6) Playback resumes when the PLAY/PAUSE button is pressed again. The new cue point is stored in the
memory.
7) Playing
7. CUEING
• ”Cueing” is the action of preparing for playback. When the Cue button is pressed, playback returns to the cue
point and enters pause mode. When the PLAY/PAUSE button is pressed during the cue mode, playback
starts.
• CUE POINT SETTING:
A Playback starts from pause or skip to a new track during play or pause. The beginning play point will be
set to the cue point.
Or,
B Press the REALTIME CUE button during playback to set the new cue point.
Or
C Memorize any of 10 CUE points by pressing MEMORY then set desired Cue then press any of 10
number buttons. You can also set any of the 10 Cue points by pressing MEMORY then any of the
NUMBER Buttons.
To return to a CUE POINT press CUE BUTTON. This will return to point A or B above.
The player has completed the cue or pause operation and is waiting for the play start command.
When the PLAY/PAUSE button is pressed, playback starts.
To Return to any of the 10 Cue points, press RECALL, then desired number buttons. The player has
completed the cue or pause operation and is waiting for the play start command. When the PLAY
/PAUSE button is pressed, playback starts.
NOTE: When play starts via pause or track skipping or scanning, the CUE POINT will change to the start
point automatically.
8. AUTO CUE
When disk is loaded, the cue point is set to the first source of music.
If track is changed before pressing play, the CUE POINT is changed to the new starting point.
If you pause during playback this also sets the new CUE POINT.
9. FRAME SEARCH
This is done by first pausing then using the jog wheel to set the starting point. (When you use the jog wheel
the monitor function allows you to here what is playing. Once you have set starting point press PLAY then
CUE to again mute output.)
10. SCANNING (FAST FORWARD / FAST REVERSE)
To do this rotate Shuttle wheel forward or reverse.
You can scan or reverse in 6 different speeds depending on how much you rotate the wheel.
American audio • DCD-PRO300™ INSTRUCTIONS MANUAL • PAGE 9
BASIC OPERATIONS (CONT.)
11. LOOP PLAY
You can loop between two points continuously.
Press IN REAL TIME CUE Button for starting point
Set end point by pressing OUT/EZIT Button, CD will begin looping until OUT/EXIT Buttonis pressed again.
Press Reloop to again enter the loop.
NOTE: this is not a seamless function.
12. TIME DISPLAY
During normal play, each time you press TIME button, the display changes to give you the following information
(Fig.14)
A = ELAPSED playing time .
B = REMAINing time in a selection. If the current selection number is over 34, “...................” is displayed.
C = TOTAL remaining time of the disc .
13. REPEAT PLAYBACK
1)
Press REPEAT button, the REPEAT 1 indicator lights , the player repeats the one track selected.
2)
Press REPEAT button again, the REPEAT ALL indicator lights . The player will then repeat all tracks on disc.
3)
Press REPEAT button again, the repeat function is cancelled.
14. PITCH BENDING
•
The speed increases or decreases respectively while the PITCH BEND+(9) or PITCH BEND- button is
pressed. The extent to which the speed changes is proportionate to the amount of time the button is pressed.
For example, if the PITCH BEND+ button is held in continuously, the speed increases continuously.
•
The pitch changed within a range of +/- 16% .
•
The jog wheel will temporarily bend the pitch of the music if the song is already playing by rotating the wheel clockwise to
speed up or counterclockwise to slow down. The speed that you rotate the JOG WHEEL determines the percentage
of the PITCH BEND.
15. PROGRAM PLAY
Press the PROG. BUTTON to make the unit enter the program mode and stop condition.
The program indicator light. Select Track using NUMBER button press PROG. again.
Repeat this up to 30 times.
Press the PLAY BUTTON to begin playing programmed tracks.
To cancel Program press and hold PROG. BUTTON more than 2 seconds.
MATCHING THE BEATS PER MINUTE (BPM)
(1) Find the BPM of the song playing by pressing the BPM BUTTON. Then tap COUNTER BUTTON (18) firmly to the beat of the
music until BPM is displayed on the LCD
(2) Repeat step 1 for the song you want to mix in. You can listen in by cueing it in your headphones using your mixer or by follow
the BEAT LED on the CD .
(3) Engage Pitch by pressing PITCH on the side you want to use, make sure Readout is in BPM by pressing BPM BUTTON until
BPM is lit on LCD. Adjust pitch until same BPM as original song is reached.
American audio • DCD-PRO300™ INSTRUCTIONS MANUAL • PAGE 10
BEFORE SWITCHING OFF THE POWER
•
When you have finished using the CD player, and before switching off the power, be sure that the disc holder has been closed with
the OPEN/CLOSE button (see figures 25 & 26).
•
TRAY PROTECTION: If tray is not closed after 60 seconds, it will close automatically and pause.
CAUTION: DO NOT forcibly close the disc holder when the power is off.
Fig. 15
Switch off the power after the disc holder has
been closed with the OPEN/CLOSE button.
DO NOT switch off the power when
the disc holder is open.
COMPACT DISCS
1.
PRECAUTIONS ON HANDLING COMPACT DISCS
•
Do not allow fingerprints, oil or dust to get on the
surface of the disc. If the disc is dirty, wipe it off with
a soft dry cloth.
•
Do not use benzene, thinner, water, record spray,
electrostatic-proof chemicals, or silicone-treated
cloths to clean discs.
•
Always handle discs carefully to prevent damaging the
surface; in particular when removing a disc from its
•
Do not bend the disc.
•
Do not apply heat.
•
Do not enlarge the hole in the center of the disc.
•
Do not write on the label (printed side) with a hardtipped implement such as a pencil or ball point pen.
•
Condensation will form if a disc is brought into
a warm area from a colder one, such as
outdoors in winter. Do not attempt to dry the
disc with a hair dryer, etc.
2.
PRECAUTION ON STORAGE
•
After playing a disc, always unload it from player.
•
Always store the compact disc in the jewel case,
protecting from dirt or damage.
•
Do not place discs in the following areas:
a) Areas exposed to direct sunlight for a
considerable time.
b) Areas subject to accumulation of dust or high
humidity.
c) Areas affected by heat from indoor heaters, etc.
CDS LEFT IN PLAYER
If a CD is left in the player and the remote has been disconnected, plug power cable in, turn on power and take
out CD.
American audio • DCD-PRO300™ INSTRUCTIONS MANUAL • PAGE 11
SPECIFICATIONS
GENERAL
Type:
Disc type:
Dimensions:
Twin mechanism compact disc player with wired controller.
Standard compact discs (5 in / 12cm and 3in/8cm discs)
Player unit:
19"(W) x 3 15/32” (H) x 9 55/64” (D)
482mm (W) x 88.8mm (H) x 264mm (D) (without feet)
Control unit: 19"(W) x 5 3/4” (H) x 1 1/2” (D)
482mm (W) x 132mm (H) x 74mm (D) (without feet)
19-inch rack mountable
Player unit:
2U / 2 rack spaces
Control unit: 3U / 3 rack spaces
Player unit:
11 lbs. / 5 kgs
Control unit: 4.5 lbs. / 2 kg
115/230V AC, 50/60Hz
25W
Operational temperature:
5 to 35˚C
(41 to 95˚F)
Operational humidity:
25 to 85%
(no condensation)
Storage temperature:
-20 to 60˚C (4 to 140˚F)
Connecting cord (2 sets for left and right channels)
Control cord (1.8m / 6 feet)
Installation:
Weight:
Power supply:
Power consumption:
Environmental conditions:
Accessories:
AUDIO SECTION
Quantization:
16 bit linear per channel
Sampling rate:
44.1 kHz at normal pitch
Over sampling rate:
8 times
D/A conversion
16 bit
Frequency response:
10 to .20,000 KHz
Total harmonic distortion:* 0.01%
Signal to noise ratio:*
85 dB
Channel separation:*
86 dB
Output level:
2.0V +/- 1dB
Load impedance:
47 kohm or more
* with 20KHz low pass filter
FUNCTIONS
Variable pitch:
+/-12% or more
Search accuracy:
1/75 sec. (1 subcode frame)
Specifications and design are subject to change without notice for purpose of improvement.
American AUDIO® World Headquarters:
4295 Charter Street
Los Angeles, CA 90058 USA
Tel: 323-582-2650
Fax: 323-582-2610
Web: www.americanaudio.us
E-mail: info@americandj.com
American audio • DCD-PRO300™ INSTRUCTIONS MANUAL • PAGE 12