Cisco 2950-12 - Catalyst Switch Installation guide

Catalyst 2950 Desktop Switch
Hardware Installation Guide
July 2002
Corporate Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 526-4100
Customer Order Number: DOC-7811157=
Text Part Number: 78-11157-03
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT
NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT
ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR
THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION
PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO
LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense.
The following information is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate
radio-frequency energy. If it is not installed in accordance with Cisco’s installation instructions, it may cause interference with radio and television
reception. This equipment has been tested and found to comply with the limits for a Class B digital device in accordance with the specifications in
part 15 of the FCC rules. These specifications are designed to provide reasonable protection against such interference in a residential installation.
However, there is no guarantee that interference will not occur in a particular installation.
Modifying the equipment without Cisco’s written authorization may result in the equipment no longer complying with FCC requirements for Class
A or Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct
any interference to radio or television communications at your own expense.
You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco
equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by
using one or more of the following measures:
• Turn the television or radio antenna until the interference stops.
• Move the equipment to one side or the other of the television or radio.
• Move the equipment farther away from the television or radio.
• Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television
or radio are on circuits controlled by different circuit breakers or fuses.)
Modifications to this product not authorized by Cisco Systems, Inc. could void the FCC approval and negate your authority to operate the product.
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as
part of UCB’s public domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE
PROVIDED “AS IS” WITH ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED
OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL
DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR
INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES.
CCIP, the Cisco Powered Network mark, the Cisco Systems Verified logo, Cisco Unity, Follow Me Browsing, FormShare, Internet Quotient, iQ
Breakthrough, iQ Expertise, iQ FastTrack, the iQ Logo, iQ Net Readiness Scorecard, Networking Academy, ScriptShare, SMARTnet, TransPath, and
Voice LAN are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, Discover All That’s Possible, The Fastest Way to
Increase Your Internet Quotient, and iQuick Study are service marks of Cisco Systems, Inc.; and Aironet, ASIST, BPX, Catalyst, CCDA, CCDP, CCIE,
CCNA, CCNP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, the Cisco IOS logo, Cisco Press, Cisco Systems, Cisco Systems Capital,
the Cisco Systems logo, Empowering the Internet Generation, Enterprise/Solver, EtherChannel, EtherSwitch, Fast Step, GigaStack, IOS, IP/TV,
LightStream, MGX, MICA, the Networkers logo, Network Registrar, Packet, PIX, Post-Routing, Pre-Routing, RateMUX, Registrar, SlideCast,
StrataView Plus, Stratm, SwitchProbe, TeleRouter, and VCO are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain
other countries.
All other trademarks mentioned in this document or Web site are the property of their respective owners. The use of the word partner does not imply a
partnership relationship between Cisco and any other company. (0203R)
Catalyst 2950 Desktop Switch Hardware Installation Guide
Copyright © 2001–2002, Cisco Systems, Inc.
All rights reserved.
C ON T E NT S
Cisco Limited Lifetime Hardware Warranty Terms xi
Preface xv
Audience xv
Purpose xv
Organization xvi
Conventions xvi
Related Publications xix
Obtaining Documentation xx
World Wide Web xx
Documentation CD-ROM xxi
Ordering Documentation xxi
Documentation Feedback xxi
Obtaining Technical Assistance xxii
Cisco.com xxii
Technical Assistance Center xxiii
Cisco TAC Website xxiii
Cisco TAC Escalation Center xxiv
CHAPTER
1
Overview 1-1
Features 1-1
Front-Panel Description 1-3
10/100 Ports 1-6
10/100/1000 Ports 1-7
100BASE-FX and 1000BASE-SX Ports 1-8
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
v
Contents
GBIC Module Ports 1-8
LEDs 1-9
System LED 1-12
RPS LED 1-13
Port Mode and Port Status LEDs 1-13
Rear-Panel Description 1-20
Power Connectors 1-22
Internal Power Supply Connector 1-22
DC Power Connector 1-22
Cisco RPS Connector 1-23
Console Port 1-23
Management Options 1-23
CHAPTER
2
Installation 2-1
Preparing for Installation 2-2
Warnings 2-2
EMC Regulatory Statements 2-4
U.S.A. 2-4
Taiwan 2-4
Japan 2-5
Korea 2-5
Hungary 2-6
Installation Guidelines 2-6
Verifying Package Contents 2-7
Installing the Switch in a Rack 2-9
Attaching the Brackets to the Switch 2-10
Mounting the Switch in a Rack 2-19
Attaching the Optional Cable Guide 2-19
Installing the Switch on a Table, Shelf, or Desk 2-20
Catalyst 2950 Desktop Switch Hardware Installation Guide
vi
78-11157-03
Contents
Installing the GBIC Modules 2-20
Powering On the Switch 2-22
Connecting to DC Power 2-23
Preparing for Installation 2-23
Grounding the Switch 2-24
Wiring the DC-Input Power Source 2-26
Running POST 2-32
Connecting to 10/100 and 10/100/1000 Ports 2-33
Connecting to 100BASE-FX and 1000BASE-SX Ports 2-37
Connecting to GBIC Module Ports 2-38
Connecting to 1000BASE-X GBIC Module Ports 2-39
Connecting to 1000BASE-T GBIC Module Ports 2-41
Connecting to GigaStack GBIC Module Ports 2-42
Connecting a PC or a Terminal to the Console Port 2-43
Where to Go Next 2-45
CHAPTER
3
Troubleshooting 3-1
Understanding POST Results 3-2
Diagnosing Problems 3-2
APPENDIX
A
Technical Specifications A-1
APPENDIX
B
Connectors and Cables B-1
Connector Specifications B-1
10/100 Ports B-1
10/100/1000 Ports B-3
Connecting to 10BASE-T and 100BASE-TX Devices B-3
Connecting to 1000BASE-T Devices B-3
100BASE-FX and 1000BASE-SX Ports B-4
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
vii
Contents
1000BASE-X GBIC Module Ports B-5
1000BASE-T GBIC Module Ports B-5
GigaStack GBIC Module Ports B-6
Console Port B-6
Cable and Adapter Specifications B-7
Two Twisted-Pair Cable Pinouts B-7
Four Twisted-Pair Cable Pinouts for 10/100 Ports B-8
Four Twisted-Pair Cable Pinouts for 1000BASE-T Ports B-9
Cable and Adapter Pinouts B-10
Connecting to a PC B-10
Connecting to a Terminal B-11
Identifying a Rollover Cable B-12
APPENDIX
C
Translated Safety Warnings C-1
Attaching the Cisco RPS (model PWR300-AC-RPS-N1) C-2
Lightning Activity Warning C-3
Installation Warning C-4
Main Disconnecting Device C-5
Chassis Warning—Rack-Mounting and Servicing C-6
Overtemperature Warning C-11
No On/Off Switch Warning C-12
Grounded Equipment Warning C-13
Product Disposal Warning C-14
Ground Connection Warning C-15
Jewelry Removal Warning C-17
Stacking the Chassis Warning C-19
Qualified Personnel Warning C-20
Class 1 Laser Product Warning C-21
Catalyst 2950 Desktop Switch Hardware Installation Guide
viii
78-11157-03
Contents
Laser Beam Exposure Warning C-22
Catalyst 2950G-24-EI-DC Service Requirement C-23
Restricted Area Equipment Installation C-24
Ethernet Cable Shielding in Offices C-25
DC Power Disconnection Warning C-26
Exposed DC Power Wire Warning C-29
Service Personnel Warning C-30
INDEX
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
ix
Contents
Catalyst 2950 Desktop Switch Hardware Installation Guide
x
78-11157-03
Cisco Limited Lifetime Hardware
Warranty Terms
There are special terms applicable to your hardware warranty as well as services
you may use during the warranty period. Your formal Warranty Statement,
including the warranty applicable to Cisco software, appears in the CD which
accompanies your Cisco Product. Follow these steps to access and download the
Cisco Information Packet and your warranty document from the CD or from
Cisco.com.
1.
Launch your browser and go to the following URL:
http://www.cisco.com/univercd/cc/td/doc/es_inpck/cetrans.htm
The Warranties and License Agreement page appears.
2.
To view the Cisco Information Packet, perform these steps:
a. Click the Information Packet Number field and make sure that the part
number 78-5235-02C0 is highlighted.
b. Select the language to view the document.
c. Click Go. The Information Packet page appears.
d. From this page you can review the document online or click the PDF icon
to download and print the document in Adobe Portable Data File (PDF)
format.
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
xi
Cisco Limited Lifetime Hardware Warranty Terms
Note
3.
You must have Adobe Acrobat Reader in order to view and print
a PDF file. If you do not have the viewer, click the Get Acrobat
Reader icon at the bottom of the page to go to the Adobe.com
website and download the reader.
To view translated and/or localized warranty information about your product,
follow these steps:
a. Enter the following part number in the Warranty Document Number
field:
78-6310-02C0
b. Select the language to view the document.
c. Click Go. The Cisco Warranty page appears.
From this page you can review the document online or click the PDF icon to
download and print the document in Adobe Portable Data File (PDF) format.
You may also contact our Service and Support website for assistance at:
http://www.cisco.com/public/Support_root.shtml.
Duration of Hardware Warranty
As long as the original End User continues to own or use the Product, provided
that: fan and power supply warranty is limited to five (5) years. In the event of
discontinuance of product manufacture, Cisco warranty support is limited to five
(5) years from the announcement of discontinuance.
Replacement, Repair or Refund Procedure for Hardware
Cisco or its service center will use commercially reasonable efforts to ship a
replacement part within ten (10) working days after receipt of the RMA request.
Actual delivery times may vary depending on Customer location.
Cisco reserves the right to refund the purchase price as its exclusive warranty
remedy.
To Receive a Return Materials Authorization (RMA) Number
Please contact the party from whom you purchased the product. If you purchased
the product directly from Cisco, contact your Cisco Sales and Service
Representative.
Catalyst 2950 Desktop Switch Hardware Installation Guide
xii
78-11157-03
Cisco Limited Lifetime Hardware Warranty Terms
Complete the information below and keep for ready reference.
Product purchased from:
Their telephone number:
Product Model and Serial number:
Maintenance Contract number:
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
xiii
Cisco Limited Lifetime Hardware Warranty Terms
Catalyst 2950 Desktop Switch Hardware Installation Guide
xiv
78-11157-03
Preface
Audience
This guide is for the networking or computer technician responsible for installing
a Catalyst 2950 switch, hereafter referred to as the switch. We assume that you are
familiar with the concepts and terminology of Ethernet and local area networking.
Purpose
This guide describes the hardware features of Catalyst 2950 switch. It describes
the physical and performance characteristics of the switch, explains how to install
a switch, and provides troubleshooting information.
This guide does not describe how to configure software features on your switch
or describe the Catalyst 2950-specific system messages that you might encounter.
It also does not provide information about command-line interface (CLI)
commands that have been created or changed for use by the switch. For more
information, refer to the software configuration, the system message, and the
command reference guides for the switch.
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
xv
Preface
Organization
Organization
This guide is organized into these chapters:
Chapter 1, “Overview,” describes the switch ports, the standards that they
support, and the LEDs.
Chapter 2, “Installation,” contains the procedures for installing a switch on a rack,
table, shelf, or desk. It also describes how to install Gigabit Interface Converter
(GBIC) modules, how to power the switch, and how to make port connections.
Chapter 3, “Troubleshooting,” describes how to identify and resolve problems
that might arise when you are installing a switch.
Appendix A, “Technical Specifications,” lists the physical and environmental
specifications and the regulatory agency approvals.
Appendix B, “Connectors and Cables,” describes the connectors, cables, and
adapters that you use to connect the switch to another device.
Appendix C, “Translated Safety Warnings,” contains translations in various
languages of the warnings in this guide.
Conventions
This publication uses these conventions and symbols for notes, cautions, and
warnings:
Note
Caution
Means reader take note. Notes contain helpful suggestions or references to
materials not contained in this manual.
Means reader be careful. In this situation, you might do something that could
result in equipment damage or loss of data.
Catalyst 2950 Desktop Switch Hardware Installation Guide
xvi
78-11157-03
Preface
Conventions
Warning
This warning symbol means danger. You are in a situation that could cause
bodily injury. Before you work on any equipment, be aware of the hazards
involved with electrical circuitry and be familiar with standard practices for
preventing accidents. (To see translations of the warnings that appear in this
publication, refer to the Appendix C, “Translated Safety Warnings.”)
Waarschuwing
Dit waarschuwingssymbool betekent gevaar. U verkeert in een
situatie die lichamelijk letsel kan veroorzaken. Voordat u aan
enige apparatuur gaat werken, dient u zich bewust te zijn van de
bij elektrische schakelingen betrokken risico’s en dient u op de
hoogte te zijn van standaard maatregelen om ongelukken te
voorkomen. (Voor vertalingen van de waarschuwingen die in
deze publicatie verschijnen, kunt u het aanhangsel C “Translated
Safety Warnings” (Vertalingen van veiligheidsvoorschriften)
raadplegen.)
Varoitus
Tämä varoitusmerkki merkitsee vaaraa. Olet tilanteessa, joka voi
johtaa ruumiinvammaan. Ennen kuin työskentelet minkään
laitteiston parissa, ota selvää sähkökytkentöihin liittyvistä
vaaroista ja tavanomaisista onnettomuuksien ehkäisykeinoista.
(Tässä julkaisussa esiintyvien varoitusten käännökset löydät
liitteestä C "Translated Safety Warnings" (käännetyt
turvallisuutta koskevat varoitukset).)
Attention
Ce symbole d’avertissement indique un danger. Vous vous trouvez
dans une situation pouvant entraîner des blessures. Avant
d’accéder à cet équipement, soyez conscient des dangers posés
par les circuits électriques et familiarisez-vous avec les
procédures courantes de prévention des accidents. Pour obtenir
les traductions des mises en garde figurant dans cette
publication, veuillez consulter l’annexe intitulée C « Translated
Safety Warnings » (Traduction des avis de sécurité).
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
xvii
Preface
Conventions
Warnung
Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer
Situation, die zu einer Körperverletzung führen könnte. Bevor Sie
mit der Arbeit an irgendeinem Gerät beginnen, seien Sie sich der
mit elektrischen Stromkreisen verbundenen Gefahren und der
Standardpraktiken zur Vermeidung von Unfällen bewußt.
(Übersetzungen der in dieser Veröffentlichung enthaltenen
Warnhinweise finden Sie im Anhang mit dem Titel C “Translated
Safety Warnings” (Übersetzung der Warnhinweise).)
Avvertenza
Questo simbolo di avvertenza indica un pericolo. Si è in una
situazione che può causare infortuni. Prima di lavorare su
qualsiasi apparecchiatura, occorre conoscere i pericoli relativi
ai circuiti elettrici ed essere al corrente delle pratiche standard
per la prevenzione di incidenti. La traduzione delle avvertenze
riportate in questa pubblicazione si trova nell’appendice C,
“Translated Safety Warnings” (Traduzione delle avvertenze di
sicurezza).
Advarsel
Dette varselsymbolet betyr fare. Du befinner deg i en situasjon
som kan føre til personskade. Før du utfører arbeid på utstyr, må
du være oppmerksom på de faremomentene som elektriske
kretser innebærer, samt gjøre deg kjent med vanlig praksis når
det gjelder å unngå ulykker. (Hvis du vil se oversettelser av de
advarslene som finnes i denne publikasjonen, kan du se i
vedlegget C "Translated Safety Warnings" [Oversatte
sikkerhetsadvarsler].)
Aviso
Este símbolo de aviso indica perigo. Encontra-se numa situação
que lhe poderá causar danos fisicos. Antes de começar a
trabalhar com qualquer equipamento, familiarize-se com os
perigos relacionados com circuitos eléctricos, e com quaisquer
práticas comuns que possam prevenir possíveis acidentes. (Para
ver as traduções dos avisos que constam desta publicação,
consulte o apêndice C “Translated Safety Warnings” “Traduções dos Avisos de Segurança”).
Catalyst 2950 Desktop Switch Hardware Installation Guide
xviii
78-11157-03
Preface
Related Publications
¡Advertencia!
Varning!
Este símbolo de aviso significa peligro. Existe riesgo para su
integridad física. Antes de manipular cualquier equipo,
considerar los riesgos que entraña la corriente eléctrica y
familiarizarse con los procedimientos estándar de prevención de
accidentes. (Para ver traducciones de las advertencias que
aparecen en esta publicación, consultar el apéndice titulado C
“Translated Safety Warnings.”)
Denna varningssymbol signalerar fara. Du befinner dig i en situation som
kan leda till personskada. Innan du utför arbete på någon utrustning måste
du vara medveten om farorna med elkretsar och känna till vanligt
förfarande för att förebygga skador. Se förklaringar av de varningar som
förkommer i denna publikation i dokumentet Regulatory Compliance and
Safety Information (Efterrättelse av föreskrifter och säkerhetsinformation),
vilket medföljer denna anordning.
Related Publications
These documents provide complete information about the switch and are available
from this URL:
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat2950/index.htm
You can order printed copies of documents with a DOC-xxxxxx= number from the
Cisco.com sites and from the telephone numbers listed in the “Ordering
Documentation” section on page xxi.
•
Note
Release Notes for the Catalyst 2950 Switch (not orderable but is available on
Cisco.com)
Switch requirements and procedures for initial configurations and software
upgrades tend to change and therefore appear only in the release notes. Before
installing, configuring, or upgrading the switch, refer to the release notes on
Cisco.com for the latest information.
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
xix
Preface
Obtaining Documentation
•
Catalyst 2950 Desktop Switch Software Configuration Guide (order number
DOC-7811380=)
•
Catalyst 2950 Desktop Switch Command Reference (order number
DOC-7811381=)
•
Catalyst 2950 Desktop Switch System Message Guide (order number
DOC-7814233=)
•
Catalyst 2950 Desktop Switch Hardware Installation Guide (order number
DOC-7811157=)
•
Catalyst GigaStack Gigabit Interface Converter Hardware Installation Guide
(order number DOC-786460=)
•
Cluster Management Suite (CMS) online help (available only from the switch
CMS software)
•
Cisco RPS 300 Redundant Power System Hardware Installation Guide (order
number DOC-7810372=)
•
CWDM Passive Optical System Installation Note (not orderable but is
available on Cisco.com)
•
1000BASE-T GBIC Installation Notes (not orderable but is available on
Cisco.com)
Obtaining Documentation
The following sections provide sources for obtaining documentation from Cisco
Systems.
World Wide Web
You can access the most current Cisco documentation on the World Wide Web at
the following URL:
http://www.cisco.com
Translated documentation is available at the following URL:
http://www.cisco.com/public/countries_languages.shtml
Catalyst 2950 Desktop Switch Hardware Installation Guide
xx
78-11157-03
Preface
Obtaining Documentation
Documentation CD-ROM
Cisco documentation and additional literature are available in a Cisco
Documentation CD-ROM package, which is shipped with your product. The
Documentation CD-ROM is updated monthly and may be more current than
printed documentation. The CD-ROM package is available as a single unit or
through an annual subscription.
Ordering Documentation
Cisco documentation is available in the following ways:
•
Registered Cisco Direct Customers can order Cisco product documentation
from the Networking Products MarketPlace:
http://www.cisco.com/cgi-bin/order/order_root.pl
•
Registered Cisco.com users can order the Documentation CD-ROM through
the online Subscription Store:
http://www.cisco.com/go/subscription
•
Nonregistered Cisco.com users can order documentation through a local
account representative by calling Cisco corporate headquarters (California,
USA) at 408 526-7208 or, elsewhere in North America, by calling
800 553-NETS (6387).
Documentation Feedback
If you are reading Cisco product documentation on the World Wide Web, you can
send us your comments by completing the online survey. When you display the
document listing for this platform, click Give Us Your Feedback. After you
display the survey, select the manual that you wish to comment on. Click Submit to
send your comments to the Cisco documentation group.
You can e-mail your comments to bug-doc@cisco.com.
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
xxi
Preface
Obtaining Technical Assistance
To submit your comments by mail, use the response card behind the front cover
of your document, or write to the following address:
Cisco Systems
Attn: Document Resource Connection
170 West Tasman Drive
San Jose, CA 95134-9883
We appreciate your comments.
Obtaining Technical Assistance
Cisco provides Cisco.com as a starting point for all technical assistance.
Customers and partners can obtain documentation, troubleshooting tips, and
sample configurations from online tools by using the Cisco Technical Assistance
Center (TAC) website. Cisco.com registered users have complete access to the
technical support resources on the Cisco TAC website.
Cisco.com
Cisco.com is the foundation of a suite of interactive, networked services that
provides immediate, open access to Cisco information, networking solutions,
services, programs, and resources at any time, from anywhere in the world.
Cisco.com is a highly integrated Internet application and a powerful, easy-to-use
tool that provides a broad range of features and services to help you to
•
Streamline business processes and improve productivity
•
Resolve technical issues with online support
•
Download and test software packages
•
Order Cisco learning materials and merchandise
•
Register for online skill assessment, training, and certification programs
You can self-register on Cisco.com to obtain customized information and service.
To access Cisco.com, go to the following URL:
http://www.cisco.com
Catalyst 2950 Desktop Switch Hardware Installation Guide
xxii
78-11157-03
Preface
Obtaining Technical Assistance
Technical Assistance Center
The Cisco TAC is available to all customers who need technical assistance with a
Cisco product, technology, or solution. Two types of support are available through
the Cisco TAC: the Cisco TAC Web Site and the Cisco TAC Escalation Center.
Inquiries to Cisco TAC are categorized according to the urgency of the issue:
•
Priority level 4 (P4)—You need information or assistance concerning Cisco
product capabilities, product installation, or basic product configuration.
•
Priority level 3 (P3)—Your network performance is degraded. Network
functionality is noticeably impaired, but most business operations continue.
•
Priority level 2 (P2)—Your production network is severely degraded,
affecting significant aspects of business operations. No workaround is
available.
•
Priority level 1 (P1)—Your production network is down, and a critical impact
to business operations will occur if service is not restored quickly. No
workaround is available.
Which Cisco TAC resource you choose is based on the priority of the problem and
the conditions of service contracts, when applicable.
Cisco TAC Website
The Cisco TAC website allows you to resolve P3 and P4 issues yourself, saving
both cost and time. The site provides around-the-clock access to online tools,
knowledge bases, and software. To access the Cisco TAC website, go to the
following URL:
http://www.cisco.com/tac
All customers, partners, and resellers who have a valid Cisco services contract
have complete access to the technical support resources on the Cisco TAC
website. The Cisco TAC website requires a Cisco.com login ID and password. If
you have a valid service contract but do not have a login ID or password, go to the
following URL to register:
http://www.cisco.com/register/
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
xxiii
Preface
Obtaining Technical Assistance
If you cannot resolve your technical issues by using the Cisco TAC website, and
you are a Cisco.com registered user, you can open a case online by using the TAC
Case Open tool at the following URL:
http://www.cisco.com/tac/caseopen
If you have Internet access, it is recommended that you open P3 and P4 cases
through the Cisco TAC website.
Cisco TAC Escalation Center
The Cisco TAC Escalation Center addresses issues that are classified as priority
level 1 or priority level 2; these classifications are assigned when severe network
degradation significantly impacts business operations. When you contact the TAC
Escalation Center with a P1 or P2 problem, a Cisco TAC engineer will
automatically open a case.
To obtain a directory of toll-free Cisco TAC telephone numbers for your country,
go to the following URL:
http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml
Before calling, please check with your network operations center to determine the
level of Cisco support services to which your company is entitled; for example,
SMARTnet, SMARTnet Onsite, or Network Supported Accounts (NSA). In
addition, please have available your service agreement number and your product
serial number.
Catalyst 2950 Desktop Switch Hardware Installation Guide
xxiv
78-11157-03
C H A P T E R
1
Overview
This chapter provides information about these topics:
•
Features, page 1-1
•
Front-Panel Description, page 1-3
•
Rear-Panel Description, page 1-20
•
Management Options, page 1-23
Features
The Catalyst 2950 switches are stackable Ethernet switches to which you can
connect workstations and other network devices, such as servers, routers, and
other switches. The switches can be deployed as backbone switches, aggregating
10BASE-T, 100BASE-TX, and Gigabit Ethernet traffic from other network
devices. Refer to the switch software configuration guide for examples showing
how you might deploy the switches in your network.
Figure 1-1 through Figure 1-9 show the Catalyst 2950 switches.
These are the switch features:
•
Hardware
– Catalyst 2950-12 switch—12 10/100 Ethernet ports
– Catalyst 2950-24 switch—24 10/100 Ethernet ports
– Catalyst 2950C-24 switch—24 10/100 Ethernet ports and
2 100BASE-FX ports
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
1-1
Chapter 1
Overview
Features
– Catalyst 2950G-12-EI—12 10/100 Ethernet ports and 2 Gigabit Interface
Converter (GBIC) module slots
– Catalyst 2950G-24-EI—24 10/100 Ethernet ports and 2 GBIC module
slots
– Catalyst 2950G-24-EI-DC—24 10/100 Ethernet ports and 2 GBIC
module slots with direct current (DC)-input power
– Catalyst 2950G-48-EI—48 10/100 Ethernet ports and 2 GBIC module
slots
– Catalyst 2950SX-24 switch—24 10/100 Ethernet ports and
2 1000BASE-SX ports
– Catalyst 2950T-24 switch—24 10/100 Ethernet ports and 2 10/100/1000
Ethernet ports
– On Catalyst 2950G-12-EI, 2950G-24-EI, 2950G-24-EI-DC, and
2950G-48-EI switches, support for these GBIC modules:
1000BASE-SX GBIC
1000BASE-LX/LH GBIC
1000BASE-ZX GBIC
1000BASE-T GBIC (model WS-5483)
Coarse Wave Division Multiplexer (CWDM) fiber-optic GBIC
GigaStack GBIC
•
Configuration
– For 10/100 ports, autonegotiates the speed and duplex settings
– For 10/100/1000 ports, autonegotiates the speed and supports only
full-duplex mode
– For 100BASE-FX ports, supports only 100-Mbps and full-duplex
settings
– For 1000BASE-SX ports, supports only 1000-Mbps and full-duplex
settings
– Supports 8192 MAC addresses
– Checks for errors on a received packet, determines the destination port,
stores the packet in shared memory, and then forwards the packet to the
destination port
Catalyst 2950 Desktop Switch Hardware Installation Guide
1-2
78-11157-03
Chapter 1
Overview
Front-Panel Description
Power redundancy
•
– Connection for an optional Cisco RPS 300 Redundant Power System
(RPS) that uses alternating current (AC) input and supplies DC output to
the switch
Front-Panel Description
The switch front panel contains the ports, the LEDs, and the Mode button.
Figure 1-1 to Figure 1-9 show the switches.
SYST
RPS
STAT
UTIL DUPLX
1x
2x
Catalyst 2950-12 Switch
3x
4x
5x
SPEED
6x
7x
8x
MODE
9x
10x
11x
10Base-T
/ 100BaseTX
12x
Catalyst 295
0 SERIE
S
45568
Figure 1-1
10/100 ports
SYST
RPS
STAT
UTIL DUPLX
1
2
Catalyst 2950-24 Switch
3
SPEED
MODE
4x
5x
6x
7x
8x
9x
10x
11x
10Base-T
/ 100BaseTX
12x
13x
14x
15x
16x
17x
18x
19x
20x
21x
Catalyst 295
0 SERIE
S
22x
23x
45567
Figure 1-2
24x
10/100 ports
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
1-3
Chapter 1
Overview
Front-Panel Description
SYST
1x
RPS
STAT
UTIL DUPLX
2x
Catalyst 2950C-24 Switch
3x
4x
5x
6x
SPEED
7x
8x
9x
MODE
10x
11x
10BASE-T
/ 100BASE
-TX
12x
13x
14x
15x
16x
17x
18x
19x
20x
21x
Catalyst 295
0 SERIE
S
22x
23x
100BASE
-FX
24x
25
45570
Figure 1-3
26
10/100 ports
100BASE-FX ports
Figure 1-4
1
SYST
2
3
4
1X
5
Catalyst 2950G-12-EI Switch
6
RPS
STAT
UTIL DUPLX
7
8
9
10
11
12
SPEED
11X
2X
12X
1
Catalyst 295
0 SERIE
S
60978
MODE
2
10/100 ports
GBIC module
slots
1
SYST
1X
RPS
STAT
UTIL DUPLX
SPEED
2
3
4
5
Catalyst 2950G-24-EI Switch
6
7
8
9
10
11
12
13
11X
13X
14
15
16
17
MODE
2X
18
19
20
21
22
23
24
23X
12X
14X
1
Catalyst 295
0 SERIE
S
60977
Figure 1-5
24X
2
10/100 ports
GBIC module
slots
Catalyst 2950 Desktop Switch Hardware Installation Guide
1-4
78-11157-03
Chapter 1
Overview
Front-Panel Description
1
SYST
2
3
4
Catalyst 2950G-24-EI-DC Switch
5
1X
6
7
RPS
STAT
UTIL DUPLX
8
9
10
11
12
SPEED
13
11X
14
15
16
13X
17
18
MODE
19
20
21
2X
22
23
60977
Figure 1-6
24
23X
12X
Catalyst 295
0 SERIE
14X
1
S
24X
2
10/100 ports
GBIC module
slots
1
SYST
2
3
4
1X
RPS
5
Catalyst 2950G-48-EI Switch
6
7
STAT
8
9
10
11
UTIL
12
13
14
15
16
DUPLX
17
SPEED
MODE
15X
17X
16X
18X
18
19
20
21
22
23
24
2X
25
26
27
28
29
30
31
65507
Figure 1-7
32
33
31X
33X
32X
34X
34
35
36
37
38
39
40
41
42
43
44
45
46
47
Catalyst 295
0 SERIE
48
S
47X
1
48X
2
10/100 ports
GBIC module
slots
SYST
RPS
STAT
UTIL DUPLX
1x
2x
Catalyst 2950SX-24 Switch
3x
SPEED
MODE
4x
5x
6x
7x
8x
9x
10x
11x
10BASE-T
/ 100BASE
-TX
12x
13x
14x
15x
16x
17x
18x
19x
20x
21x
Catalyst 295
0 SERIE
S
22x
23x
24x
1000BAS
E-SX
25
74516
Figure 1-8
26
10/100 ports
1000BASE-SX ports
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
1-5
Chapter 1
Overview
Front-Panel Description
SYST
RPS
STAT
UTIL DUPLX
SPEED
1x
2x
Catalyst 2950T-24 Switch
3x
4x
5x
6x
7x
MODE
8x
9x
10x
11x
10Base-T
/ 100BaseTX
12x
13x
14x
15x
16x
17x
18x
19x
20x
21x
Catalyst 295
0 SERIE
S
22x
23x
24x
10/100/1
00Base-T
1
47337
Figure 1-9
2
10/100 ports
10/100/1000 ports
10/100 Ports
The 10/100 ports use RJ-45 connectors and twisted-pair cabling. The ports can
connect to these devices:
Note
•
10BASE-T devices, such as workstations and hubs, through standard RJ-45
connectors and two twisted-pair cabling. You can use Category 3, 4, or 5
cabling.
•
100BASE-TX devices, such as high-speed workstations, servers, hubs,
routers, and other switches, through standard RJ-45 connectors and two or
four twisted-pair, Category 5 cabling.
When connecting the switch to workstations, servers, and routers, be sure that the
cable is a twisted-pair straight-through cable. When connecting the switch to hubs
or other switches, use a twisted-pair crossover cable. Pinouts for the cables are
described in Appendix B, “Connectors and Cables.”
The 10/100 ports can be explicitly set to operate in any combination of half
duplex, full duplex, 10 Mbps, or 100 Mbps. They can also be set for speed and
duplex autonegotiation, compliant with IEEE 802.3U. In all cases, the cable
length from a switch to an attached device cannot exceed 328 feet (100 meters).
Catalyst 2950 Desktop Switch Hardware Installation Guide
1-6
78-11157-03
Chapter 1
Overview
Front-Panel Description
When set for autonegotiation, a port senses the speed and duplex settings of the
attached device and advertises its own capabilities. If the attached device supports
autonegotiation, the port negotiates the best connection (that is, the fastest line
speed that both devices support and full-duplex transmission, if the attached
device supports it) and configures itself accordingly.
10/100/1000 Ports
The 10/100/1000 ports on the Catalyst 2950T-24 switches use RJ-45 connectors
and twisted-pair cabling. The ports can connect to these devices:
•
10BASE-T devices, such as workstations and hubs, through standard RJ-45
connectors and two or four twisted-pair, Category 5 cabling.
•
100BASE-TX devices, such as high-speed workstations, servers, hubs,
routers, and other switches, through standard RJ-45 connectors and two or
four twisted-pair, Category 5 cabling.
•
1000BASE-T devices, such as high-speed workstations, servers, hubs,
routers, and other switches, through standard RJ-45 connectors and four
twisted-pair, Category 5 cabling.
Note
When connecting the switch to a 1000BASE-T device, be sure to use a four
twisted-pair, Category 5 cable.
Note
When connecting the switch to workstations, servers, and routers, be sure to use
a twisted-pair straight-through cable. When connecting the switch to hubs or other
switches, use a twisted-pair crossover cable. Pinouts for the cables are described
in Appendix B, “Connectors and Cables.”
The 10/100/1000 ports on the Catalyst 2950T-24 switches can be explicitly set to
operate at 10, 100, or 1000 Mbps but only in full-duplex mode. They can also be
set for speed autonegotiation, compliant with IEEE 802.3AB. In all cases, the
cable length from a switch to an attached device cannot exceed 328 feet
(100 meter).
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
1-7
Chapter 1
Overview
Front-Panel Description
100BASE-FX and 1000BASE-SX Ports
The 100BASE-FX and 1000BASE-SX ports both use 50/125- or 62.5/125-micron
multimode fiber-optic cabling. The 100BASE-FX ports operate only at 100 Mbps
in full-duplex mode, and the 1000BASE-SX ports operate only at 1000 Mbps in
full-duplex mode.
In full-duplex mode, the cable length from a switch to an attached device cannot
exceed 1804 feet (550 meters).
You can connect a 100BASE-FX or 1000BASE-SX port to an SC or ST port on a
target device by using one of the MT-RJ fiber-optic patch cables listed in
Table 1-1. Use the Cisco part numbers in Table 1-1 to order the patch cables that
you need.
Table 1-1
MT-RJ Patch Cables for 100BASE-FX and 1000BASE-SX
Connections
Type
Cisco Part Number
1-meter, MT-RJ-to-SC multimode cable
CAB-MTRJ-SC-MM-1M
3-meter, MT-RJ-to-SC multimode cable
CAB-MTRJ-SC-MM-3M
5-meter, MT-RJ-to-SC multimode cable
CAB-MTRJ-SC-MM-5M
1-meter, MT-RJ-to-ST multimode cable
CAB-MTRJ-ST-MM-1M
3-meter, MT-RJ-to-ST multimode cable
CAB-MTRJ-ST-MM-3M
5-meter, MT-RJ-to-ST multimode cable
CAB-MTRJ-ST-MM-5M
GBIC Module Ports
The GBIC module slots support these modules:
•
1000BASE-SX GBIC module for fiber-optic connections that cannot exceed
1804 feet (550 meter).
•
1000BASE-LX/LH GBIC module for fiber-optic connections that cannot
exceed 32,810 feet (10 kilometer).
•
1000BASE-ZX GBIC module for fiber-optic connections that cannot exceed
328,100 feet (100 kilometer).
Catalyst 2950 Desktop Switch Hardware Installation Guide
1-8
78-11157-03
Chapter 1
Overview
Front-Panel Description
•
1000BASE-T GBIC module for copper connections that cannot exceed
328 feet (100 meter).
•
CWDM GBIC module for single-mode fiber-optic connections that cannot
exceed 393,719 feet (120 kilometer).
•
GigaStack GBIC module for creating a 1-Gbps stack configuration of up to
nine supported switches. The GigaStack GBIC supports one full-duplex link
(in a point-to-point configuration) or up to nine half-duplex links (in a stack
configuration) to other Gigabit Ethernet devices. Using the required Cisco
proprietary signaling and cabling, the GigaStack GBIC-to-GigaStack GBIC
connection cannot exceed 3 feet (1 meter).
Note
Cisco-approved GBIC modules have a serial EEPROM that contains the module
serial number, the vendor name and ID, a unique security code, and cyclic
redundancy check (CRC). When a GBIC module is inserted in the switch, the
switch software reads the EEPROM to check the serial number, vendor name, and
vendor ID and recomputes the security code and CRC. If the serial number, the
vendor name or ID, security code, or CRC is invalid, the switch places the
interface in an error-disabled state.
Note
If you are using a non-Cisco approved GBIC module, remove the GBIC module
from the switch, and replace it with a Cisco-approved module.
For more information about these GBIC modules, refer to your GBIC
documentation.
LEDs
You can use the LEDs to monitor switch activity and performance. Figure 1-10,
Figure 1-11, and Figure 1-12 show the location of the LEDs and the Mode button
that you use to select the port mode. Changing the port mode changes the
information provided by each port status LED.
All of the LEDs described in this section except the utilization meter (UTIL) are
visible in the Cluster Management Suite (CMS). The switch software
configuration guide describes how to use CMS to configure and monitor
individual switches and switch clusters.
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
1-9
Chapter 1
Overview
Front-Panel Description
Figure 1-10 LEDs on Catalyst 2950-12, 2950-24, 2950C-24, 2950SX-24, and 2950T-24 Switches
RPS
LED
Port status
LEDs
System
LED
SYST
RPS
Port mode
LEDs
STAT
1x
2x
3x
UTIL D
UPLX SP
EED
4x
5x
6x
Mode button
52918
MODE
Catalyst 2950 Desktop Switch Hardware Installation Guide
1-10
78-11157-03
Chapter 1
Overview
Front-Panel Description
Figure 1-11 LEDs on Catalyst 2950G-12-EI, 2950G-24-EI, and 2950G-24-EI-DC Switches
RPS
LED
Port status
LEDs
System
LED
1
1X
RPS
Port mode
LEDs
STAT
UTIL D
UPLX S
PEED
MODE
2
3
4
5
6
7
8
9
10
11
12
11X
2X
12X
Mode button
65395
SYST
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
1-11
Chapter 1
Overview
Front-Panel Description
Figure 1-12 LEDs on Catalyst 2950G-48-EI Switches
Port status
LEDs
System
LED
1
SYST
RPS
LED
1X
RPS
2
3
4
5
6
7
8
STAT
UTIL
DUPLX
Port
mode
LEDs
9
10
11
12
13
14
15
16
SPEED
15X
MODE
16X
Mode button
65508
2X
System LED
The system LED shows whether the system is receiving power and functioning
properly. Table 1-2 lists the LED colors and meanings.
Table 1-2
System LED
Color
System Status
Off
System is not powered up.
Green
System is operating normally.
Amber
System is receiving power but is not functioning properly.
For information about the system LED colors during the power-on self-test
(POST), see the “Running POST” section on page 2-32.
Catalyst 2950 Desktop Switch Hardware Installation Guide
1-12
78-11157-03
Chapter 1
Overview
Front-Panel Description
RPS LED
The RPS LED shows the RPS status. Table 1-3 lists the LED colors and meanings.
Table 1-3
RPS LED
Color
RPS Status
Off
RPS is off or is not installed.
Solid green
RPS is connected and ready to provide back-up power.
Flashing green
RPS is connected but is unavailable because it is providing
power to another device (redundancy has been allocated to a
neighboring device).
Solid amber
RPS is in standby mode or in a fault condition. Press the
Standby/Active button on the RPS, and the LED should turn
green. If it does not, the RPS fan could have failed. Contact
Cisco Systems.
Flashing amber The internal power supply in a switch has failed, and the RPS
is providing power to the switch (redundancy has been
allocated to this device).
For more information about the Cisco RPS 300, refer to the Cisco RPS 300
Redundant Power System Hardware Installation Guide.
Port Mode and Port Status LEDs
Each port has a port status LED, also called a port LED. These LEDs, as a group
or individually, display information about the switch and the individual ports. The
port modes (see Table 1-4) determine the type of information displayed.
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
1-13
Chapter 1
Overview
Front-Panel Description
Table 1-4
Port Mode LEDs
Mode LED
Port Mode
Description
STAT
Port status
The port status. This is the default mode.
UTIL
Switch utilization
The current bandwidth in use by the switch.
DUPLX
Port duplex mode
The port duplex mode: half duplex or full duplex.
SPEED
Port speed
The port operating speed: 10 or 100 Mbps for 10/100 ports
and 10, 100, or 1000 Mbps for 10/100/1000 ports.
To select or change the port mode, press the Mode button (see Figure 1-13,
Figure 1-14, and Figure 1-15) to highlight the mode that you want. Release the
button to enable the highlighted mode.
Figure 1-13 Changing the Port Mode on Catalyst 2950-12, 2950-24, 2950C-24,
2950SX-24, and 2950T-24 Switches
SYST
RPS
STAT
1x
2x
UTIL D
UPLX SP
EED
3x
4x
5x
6x
Mode button
52917
MODE
Catalyst 2950 Desktop Switch Hardware Installation Guide
1-14
78-11157-03
Chapter 1
Overview
Front-Panel Description
Figure 1-14 Changing the Port Mode on Catalyst 2950G-12-EI, 2950G-24-EI, and
2950G-24-EI-DC Switches
1
1X
RPS
STAT
2
3
4
5
6
7
8
9
10
11
12
UTIL D
UPLX S
PEED
MODE
11X
2X
12X
Mode button
65393
SYST
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
1-15
Chapter 1
Overview
Front-Panel Description
Figure 1-15 Changing the Port Mode on Catalyst 2950G-48-EI Switches
1
SYST
RPS
2
3
4
1X
STAT
UTIL
DUPLX
5
6
7
8
9
10
11
12
13
14
15
16
SPEED
15X
2X
Mode button
16X
65509
MODE
Catalyst 2950 Desktop Switch Hardware Installation Guide
1-16
78-11157-03
Chapter 1
Overview
Front-Panel Description
When you change the port mode, the meanings of the port LED colors change.
Table 1-5 explains how to interpret these colors.
Table 1-5
Meaning of Port LED Colors in Different Modes
Port Mode
Color
Meaning
STAT (port status)
Off
No link.
Solid green
Link present.
Flashing green Activity. Port is transmitting or receiving data.
Alternating
green-amber
Link fault. Error frames can affect connectivity, and errors such
as excessive collisions, CRC errors, and alignment and jabber
errors are monitored for a link-fault indication.
Solid amber
Port is not forwarding. Port was disabled by management, an
address violation, or Spanning Tree Protocol (STP).
Note
UTIL (utilization)
DUPLX
After a port is reconfigured, the port LED can remain
amber for up to 30 seconds while STP checks the switch
for possible loops.
Green
The current backplane utilization that is displayed over the
amber LED background on a logarithmic scale.
Amber
The maximum backplane utilization since the switch was
powered on.
Green and
amber
See Figure 1-16 to Figure 1-19 for details.
Off
(half or full duplex) Green
Note
If the current utilization exceeds the maximum
utilization, the maximum utilization is automatically
updated.
Port is operating in half duplex.
Port is operating in full duplex.
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
1-17
Chapter 1
Overview
Front-Panel Description
Table 1-5
Meaning of Port LED Colors in Different Modes (continued)
Port Mode
Color
SPEED (speed)
10/100 ports
Meaning
Off
Port is operating at 10 Mbps.
Green
Port is operating at 100 Mbps.
10/100/1000 ports
Off
Port is operating at 10 Mbps.
Green
Port is operating at 100 Mbps.
Flashing green Port is operating at 1000 Mbps.
1000BASE-X GBIC module ports
Off
Port is not operating.
Green
Port is operating at 1000 Mbps.
For more information about GBIC LEDs, refer to your GBIC documentation.
Figure 1-16 to Figure 1-19 show the bandwidth utilization percentages displayed
by the right-most LEDs.
If all LEDs on Catalyst 2950-12, 2950-24, 2950C-24, 2950SX-24, and 2950T-24
switches are green (no amber showing), the switch is using 50 percent or more of
the total bandwidth. If the far-right LED is off, the switch is using more than 25
but less than 50 percent of the total bandwidth, and so on. If only the far-left LED
is green, the switch isp using less than 0.0488 percent of the total bandwidth. (See
Figure 1-16.)
If all LEDs on Catalyst 2950G-12-EI switches are green (no amber showing), the
switch is using 50 percent or more of the total bandwidth. If the LED for GBIC
module slot 2 is off, the switch is using more than 25 but less than 50 percent of
the total bandwidth. If LEDs for both GBIC module slots are off, the switch is
using less than 25 percent of the total bandwidth, and so on. (See Figure 1-17.)
If all LEDs on Catalyst 2950G-24-EI and 2950G-24-EI-DC switches are green
(no amber showing), the switch is using 50 percent or more of the total bandwidth.
If the LED for GBIC module slot 2 is off, the switch is using more than 25 but less
than 50 percent of the total bandwidth. If LEDs for both GBIC module slots are
off, the switch is using less than 25 percent of the total bandwidth, and so on. (See
Figure 1-18.)
Catalyst 2950 Desktop Switch Hardware Installation Guide
1-18
78-11157-03
Chapter 1
Overview
Front-Panel Description
If all LEDs on Catalyst 2950G-48-EI switches are green (no amber showing), the
switch is using 50 percent or more of the total bandwidth. If the LED for GBIC
module slot 2 is off, the switch is using more than 25 but less than 50 percent of
the total bandwidth. If LEDs for both GBIC module slots are off, the switch is
using less than 25 percent of the total bandwidth, and so on. (See Figure 1-19.)
Figure 1-16 Bandwidth Utilization on Catalyst 2950-12, 2950-24, 2950C-24,
2950SX-24, and 2950T-24 Switches
Catalyst 2950 SERIES
10Base-T / 100Base-TX
1x
3x
4x
5x
6x
7x
8x
9x
10x
11x
12x
RPS
47267
SYST
STAT
2x
UTIL DUPLX SPEED
MODE
0–0.0487%+
6.25–12.4%+
12.5–24%+
25–49%+
50%+
Figure 1-17 Bandwidth Utilization on Catalyst 2950G-12-EI Switches
2
3
4
5
6
7
8
9
10
Catalyst 2950
11 12
11X
1
STAT
2
RPS
UTIL
DUPLX
SPEED
2X
12X
MODE
65397
1
1X
SYST
< 25% +
25% – 49% +
50% +
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
1-19
Chapter 1
Overview
Rear-Panel Description
Figure 1-18 Bandwidth Utilization on Catalyst 2950G-24-EI and 2950G-24-EI-DC
Switches
2
3
4
5
6
7
8
9
10
11 12
13 14
11X
15 16
17 18
19 20
21 22
Catalyst 2950
23 24
13X
15X
1
STAT
65396
1
1X
SYST
2
RPS
UTIL
DUPLX
SPEED
2X
12X
14X
16X
MODE
< 25% +
25% – 49% +
50% +
Figure 1-19 Bandwidth Utilization on Catalyst 2950G-48-EI Switches
Catalyst 2950
1
2
3
24
5
6
7
8
9
10
11 12
13 14
15 16
17 18
19 20
21 22
23 24
25 26
27 28
29 31
31 32
33 34
35 36
37 38
39 40
41 42
43 44
45 46
47 48
1X
15X
17X
31X
33X
47X
2X
16X
18X
32X
34X
48X
2
MODE
65510
1
SYST
RPS
STAT
UTIL
DUPLX
SPEED
< 25% +
25% – 49% +
50% +
Rear-Panel Description
Other than the Catalyst 2950G-24-EI-DC switch, the rear panel of a Catalyst 2950
switch has an AC power connector, an RPS connector, and an RJ-45 console port.
(See Figure 1-20 and Figure 1-21.)
The rear panel of the Catalyst 2950G-24-EI-DC switch has a DC power connector
(also referred to as the terminal block header), a DC ground lug, an RPS
connector, and an RJ-45 console port. (See Figure 1-22.)
Catalyst 2950 Desktop Switch Hardware Installation Guide
1-20
78-11157-03
Chapter 1
Overview
Rear-Panel Description
Figure 1-20 Catalyst 2950 Switch Rear Panel
DC INPUT
FO
POWE R REMOTE
SPECIF R SUPPLY
IED IN
+12V @4MANUAL.
.5A
45585
RATING
100-127V~
@ 1A
200-240V~
@0.5A
50-60Hz
CONSOLE
AC power
connector
RPS
connector
Fan
RJ-45
console port
Figure 1-21 Catalyst 2950G-48-EI Switch Rear Panel
DC INPUT
FO
POWE R REMOTE
SPECIF R SUPPLY
IED IN
+12V @4MANUAL.
.5A
65511
RATING
100-127V~
@ 1A
200-240V~
@0.5A
50-60Hz
CONSOLE
AC power
connector
RPS
connector
Fan
exhaust
RJ-45
console port
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
1-21
Chapter 1
Overview
Rear-Panel Description
36 - 72V
1 - 0.5A
DC INPUT
FO
POWE R REMOTE
SPECIF R SUPPLY
IED IN
+12V @4MANUAL.
.5A
A
B
CONSOLE
DC power
connector
RPS
connector
Fan
65291
Figure 1-22 Catalyst 2950G-24-EI-DC Switch Rear Panel
RJ-45
DC
console ground
port
lug
Power Connectors
You can provide power to a switch by using the AC internal power supply, the
DC-input power source, or the Cisco RPS.
Internal Power Supply Connector
The internal AC power supply is an autoranging unit that supports input voltages
between 100 and 240 VAC. Other than for the Catalyst 2950G-24-EI-DC switch,
use the supplied AC power cord to connect the AC power connector to an AC
power outlet.
DC Power Connector
The Catalyst 2950G-24-EI-DC switch has an internal DC-power converter. It has
dual feeds (A and B) that are diode-OR-ed into a single power block. For
installation instructions, see the “Connecting to DC Power” section on page 2-23.
Caution
You must connect the Catalyst 2950G-24-EI-DC switch only to a DC-input power
source that has an input supply voltage from –36 to –72 VDC. If the supply
voltage is not in this range, the switch might not operate properly or might be
damaged.
Catalyst 2950 Desktop Switch Hardware Installation Guide
1-22
78-11157-03
Chapter 1
Overview
Management Options
Cisco RPS Connector
The RPS is a 300W redundant power system that can support six external network
devices and provides DC power to one failed device at a time. It automatically
senses when the internal power supply of a connected device fails and provides
power to that device, preventing loss of network traffic.
Warning
Attach only the Cisco RPS 300 (model PWR300-AC-RPS-N1) to the RPS
receptacle.
For more information about the Cisco RPS 300, refer to the documentation that
came with the RPS 300.
Console Port
You can connect a switch to a PC through the console port and the supplied
RJ-45-to-DB-9 adapter cable. If you want to connect a switch to a terminal, you
need to provide an RJ-45-to-DB-25 female DTE adapter. You can order a kit (part
number ACS-DSBUASYN=) with that adapter from Cisco. For console-port and
adapter-pinout information, see the “Cable and Adapter Specifications” section
on page B-7.
Management Options
Catalyst 2950 switches offer these management options:
•
Cluster Management Suite (CMS)
CMS is made up of three web-based applications that you use to manage
switches. You can use Cluster Builder, which includes Cluster View, and
Cluster Manager to create, configure, and monitor switch clusters. You can
also use Device Manager to manage individual and standalone switches. For
more information, refer to the switch software configuration guide and the
CMS online help.
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
1-23
Chapter 1
Overview
Management Options
•
IOS command-line interface (CLI)
You can manage switches by using command-line entries. To access the CLI,
connect a PC or terminal directly to the console port on the switch rear panel.
If the switch is attached to your network, you can use a Telnet connection to
manage the switch from a remote location. For more information, refer to the
switch command reference.
•
CiscoView application
You can use the CiscoView device-management application to set
configuration parameters and to view switch status and performance
information. This application, which you purchase separately, can be a
standalone application or part of an Simple Network Management Protocol
(SNMP) network-management platform. For more information, refer to the
documentation that came with your CiscoView application.
•
SNMP network management
You can manage switches by using an SNMP-compatible management station
running platforms such as HP OpenView and SunNet Manager. The switch
supports a comprehensive set of MIB extensions and MIB II, the
IEEE 802.1D bridge MIB, and four Remote Monitoring (RMON) groups. For
more information, refer to the documentation that came with your SNMP
application.
•
Cisco Intelligence Engine 2100 (IE2100)
•
The Cisco IE200 Series Configuration Registrar is a network management
device that works with embedded Cisco Networking Services (CNS) agents
in the switch software. You can automate initial configurations and
configuration updates by generating switch-specific configuration changes,
sending them to the switch, executing the configuration change, and logging
the results. For more information, refer to the switch software configuration
guide and the documentation that came with your application.
Catalyst 2950 Desktop Switch Hardware Installation Guide
1-24
78-11157-03
C H A P T E R
2
Installation
This chapter describes how to install your switch, interpret the power-on self-test
(POST), and connect the switch to other devices. Read these topics and perform
the procedures in this order:
•
Preparing for Installation, page 2-2
•
Installing the Switch in a Rack, page 2-9
•
Installing the Switch on a Table, Shelf, or Desk, page 2-20
•
Installing the GBIC Modules, page 2-20
•
Powering On the Switch, page 2-22
•
Connecting to DC Power, page 2-23
•
Running POST, page 2-32
•
Connecting to 10/100 and 10/100/1000 Ports, page 2-33
•
Connecting to 100BASE-FX and 1000BASE-SX Ports, page 2-37
•
Connecting to GBIC Module Ports, page 2-38
•
Connecting a PC or a Terminal to the Console Port, page 2-43
•
Where to Go Next, page 2-45
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
2-1
Chapter 2
Installation
Preparing for Installation
Preparing for Installation
This section provides information about these topics:
•
Warnings, page 2-2
•
EMC Regulatory Statements, page 2-4
•
Installation Guidelines, page 2-6
•
Verifying Package Contents, page 2-7
Warnings
These warnings are translated into several languages in Appendix C, “Translated
Safety Warnings.”
Warning
This equipment is to be installed and maintained by service personnel only as
defined by AS/NZS 3260 Clause 1.2.14.3 Service Personnel.
Warning
Only trained and qualified personnel should be allowed to install or replace this
equipment.
Warning
Read the installation instructions before you connect the system to its power
source.
Warning
Unplug the power cord before you work on a system that does not have an on/off
switch.
Warning
Do not stack the chassis on any other equipment. If the chassis falls, it can
cause severe bodily injury and equipment damage.
Catalyst 2950 Desktop Switch Hardware Installation Guide
2-2
78-11157-03
Chapter 2
Installation
Preparing for Installation
Warning
The plug-socket combination must be accessible at all times because it serves
as the main disconnecting device.
Warning
To prevent the switch from overheating, do not operate it in an area that
exceeds the maximum recommended ambient temperature of 113° F (45° C). To
prevent airflow restriction, allow at least 3 inches (7.6 cm) of clearance around
the ventilation openings.
Warning
When installing the unit, always make the ground connection first and
disconnect it last.
Warning
This equipment is intended to be grounded. Ensure that the host is connected to
earth ground during normal use.
Warning
Before working on equipment that is connected to power lines, remove jewelry
(including rings, necklaces, and watches). Metal objects will heat up when
connected to power and ground and can cause serious burns or weld the metal
object to the terminals.
Warning
Do not work on the system or connect or disconnect cables during periods of
lightning activity.
Warning
Ultimate disposal of this product should be handled according to all national
laws and regulations.
Warning
Attach only the Cisco RPS (model PWR300-AC-RPS-N1) to the RPS receptacle.
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
2-3
Chapter 2
Installation
Preparing for Installation
Warning
Class 1 laser product
Warning
Avoid exposure to the laser beam.
EMC Regulatory Statements
This section includes specific regulatory statements about the Catalyst 2950
switches.
U.S.A.
U.S. regulatory information for this product is in the front matter of this manual.
Taiwan
This is a Class A Information product. When used in a residential environment, it
may cause radio frequency interference. Under such circumstances, the user may
be requested to take appropriate countermeasures.
Catalyst 2950 Desktop Switch Hardware Installation Guide
2-4
78-11157-03
Chapter 2
Installation
Preparing for Installation
Japan
46464
This is a Class A product based on the standard of the Voluntary Control Council
for Interference by Information Technology Equipment (VCCI). If this equipment
is used in a domestic environment, radio disturbance may arise. When such
trouble occurs, the user may be required to take corrective actions.
Korea
Warning
This is a Class A Device and is registered for EMC requirements for industrial
use. The seller or buyer should be aware of this. If this type was sold or
purchased by mistake, it should be replaced with a residential-use type.
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
2-5
Chapter 2
Installation
Preparing for Installation
Hungary
This equipment is a Class A product and should be used and installed properly
according to the Hungarian EMC Class A requirements (MSZEN55022). Class A
equipment is designed for typical commercial establishments for which special
conditions of installation and protection distance are used.
Figyelmeztetés a felhasználói kézikönyv számára:
Ez a berendezés “A” osztályú termék, felhasználására és üzembe helyezésére a
magyar EMC “A” osztályú követelményeknek (MSZ EN 55022) megfeleloen
kerülhet sor, illetve ezen “A” osztályú berendezések csak megfelelo kereskedelmi
forrásból származhatnak, amelyek biztosítják a megfelelo speciális üzembe
helyezési körülményeket és biztonságos üzemelési távolságok alkalmazását.
Installation Guidelines
When determining where to place the switch, observe these guidelines.
•
For 10/100 ports and 10/100/1000 ports, the cable length from a switch to an
attached device cannot exceed 328 feet (100 meters).
•
For 100BASE-FX ports, the cable length from a switch to an attached device
cannot exceed 6562 feet (2 kilometers).
•
For 1000BASE-SX ports and 1000BASE-SX GBIC module ports, the cable
length from a switch to an attached device cannot exceed 1804 feet
(550 meters).
•
For 1000BASE-LX/LH GBIC module ports, the cable length from a switch to
an attached device cannot exceed 32,810 feet (10 kilometers).
•
For 1000BASE-ZX GBIC module ports, the cable length from a switch to an
attached device cannot exceed 328,100 feet (100 kilometers).
•
For 1000BASE-T GBIC module ports, the cable length from switch to an
attached device cannot exceed 328 feet (100 meters).
•
For Coarse Wave Division Multiplexing (CWDM) GBIC module ports, the
cable length from a switch to an attached device cannot exceed 393,719 feet
(120 kilometers). For specific cable lengths, refer to the CWDM GBIC
module documentation.
•
For GigaStack GBIC module ports, the cable length from a switch to an
attached device cannot exceed 3 feet (1 meter).
Catalyst 2950 Desktop Switch Hardware Installation Guide
2-6
78-11157-03
Chapter 2
Installation
Preparing for Installation
•
Operating environment is within the ranges listed in Appendix A, “Technical
Specifications.”
•
Clearance to front and rear panels meet these conditions:
– Front-panel LEDs can be easily read.
– Access to ports is sufficient for unrestricted cabling.
– Rear-panel AC power connector is within reach of an AC power outlet.
– Rear-panel direct current (DC) power connector is within reach of a
circuit breaker.
•
Airflow around the switch and through the vents is unrestricted.
•
Temperature around the unit does not exceed 113°F (45°C).
Note
•
If the switch is installed in a closed or multirack assembly, the
temperature around it might be greater than normal room
temperature.
Cabling is away from sources of electrical noise, such as radios, power lines,
and fluorescent lighting fixtures.
Verifying Package Contents
Note
Carefully remove the contents from the shipping container, and check each item
for damage. If any item is missing or damaged, contact your Cisco representative
or reseller for support. Return all packing materials to the shipping container and
save them.
The switch is shipped with these items:
•
This Catalyst 2950 Desktop Switch Hardware Installation Guide
•
Where to Find the Catalyst 2950 Documentation flyer
•
Cisco Documentation CD-ROM
•
AC power cord
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
2-7
Chapter 2
Installation
Preparing for Installation
•
Mounting kit containing these items:
– Four rubber feet for mounting the switch on a table, shelf, or desk
– Two 19-inch or 24-inch rack-mounting brackets
– Six number-8 Phillips flat-head screws for attaching the brackets to the
switch
– Four number-8 Phillips truss-head screws for attaching the brackets to
the switch
– Four number-12 Phillips machine screws for attaching the brackets to a
rack
– One cable guide and one black Phillips machine screw for attaching the
cable guide to one of the mounting brackets
•
DC-switch kit containing these items:
– One DC terminal block plug (also called a terminal block header)
– One ground lug
– Two number-10-32 screws for attaching the ground lug to the switch
– Two 23-inch rack-mounting brackets (with 1-inch spacing for telco
racks)
– Four number-8 Phillips truss-head screws for attaching the brackets to
the switch
– Two number-12 Phillips machine screws for attaching the brackets to a
rack
Note
The DC-switch kit ships only with the Catalyst 2950G-24-EI-DC switch.
•
One RJ-45-to-DB-9 adapter cable
•
Cisco Information Packet, containing safety and support information
If you want to connect a terminal to the switch console port, you need to provide
an RJ-45-to-DB-25 female DTE adapter. You can order a kit (part number
ACS-DSBUASYN=) with that adapter from Cisco.
Catalyst 2950 Desktop Switch Hardware Installation Guide
2-8
78-11157-03
Chapter 2
Installation
Installing the Switch in a Rack
You can connect a 100BASE-FX or 1000BASE-SX port to an SC or ST port on a
target device by using one of the MT-RJ fiber-optic patch cables listed in
Table 2-1. Use the Cisco part numbers in Table 2-1 to order the patch cables that
you need.
Table 2-1
MT-RJ Patch Cables for 100BASE-FX and 1000BASE-SX Connections
Type
Cisco Part Number
1-meter, MT-RJ-to-SC multimode cable
CAB-MTRJ-SC-MM-1M
3-meter, MT-RJ-to-SC multimode cable
CAB-MTRJ-SC-MM-3M
5-meter, MT-RJ-to-SC multimode cable
CAB-MTRJ-SC-MM-5M
1-meter, MT-RJ-to-ST multimode cable
CAB-MTRJ-ST-MM-1M
3-meter, MT-RJ-to-ST multimode cable
CAB-MTRJ-ST-MM-3M
5-meter, MT-RJ-to-ST multimode cable
CAB-MTRJ-ST-MM-5M
Installing the Switch in a Rack
Warning
Note
To prevent bodily injury when mounting or servicing this unit in a rack, you must
take special precautions to ensure that the system remains stable. The
following guidelines are provided to ensure your safety:
•
This unit should be mounted at the bottom of the rack if it is the
only unit in the rack.
•
When mounting this unit in a partially filled rack, load the rack
from the bottom to the top with the heaviest component at the
bottom of the rack.
•
If the rack is provided with stabilizing devices, install the
stabilizers before mounting or servicing the unit in the rack.
Figure 2-1 to Figure 2-17 show the Catalyst 2950-24, 2950G-24-EI-DC, and
2950G-48-EI switches as examples. You can install other Catalyst 2950 switches
in a rack as shown in these illustrations.
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
2-9
Chapter 2
Installation
Installing the Switch in a Rack
To install the switch in a 19-, 23-, or 24-inch rack, follow these steps:
Note
•
Attaching the Brackets to the Switch, page 2-10
•
Mounting the Switch in a Rack, page 2-19
•
Attaching the Optional Cable Guide, page 2-19
Installing the Catalyst 2950G-48-EI switch in a 23-inch or 24-inch rack requires
an optional bracket kit not included with the switch. You can order a kit
containing the 23-inch or 24-inch rack-mounting brackets and hardware from
Cisco (part number RCKMNT-1RU=).
Attaching the Brackets to the Switch
The bracket orientation and the screws that you use depend on whether you are
attaching the brackets to a 19-, 23-, or 24-inch rack. Follow these guidelines:
•
When mounting a switch other than a Catalyst 2950G-48-EI switch in a
19-inch rack, use two Phillips flat-head screws to attach the long side of the
19- or 24-inch bracket to the switch. See Figure 2-1, Figure 2-2, and
Figure 2-3.
•
When mounting a Catalyst 2950G-48-EI switch in a 19-inch rack, use three
Phillips flat-head screws to attach the long side of the 19- or 24-inch bracket
to the switch. See Figure 2-4, Figure 2-5, and Figure 2-6.
•
When mounting a Catalyst 2950G-24-EI-DC switch in a 23-inch rack, use
two Phillips truss-head screws to attach the 23-inch bracket to the switch. See
Figure 2-7, Figure 2-8, and Figure 2-9.
•
When mounting a switch other than a Catalyst 2950G-48-EI switch in a
24-inch rack, use two Phillips truss-head screws to attach the 19- or 24-inch
bracket to the switch. See Figure 2-10, Figure 2-11, and Figure 2-12.
•
When mounting a Catalyst 2950G-48-EI switch in a 24-inch rack, use three
Phillips flat-head screws to attach the 24-inch bracket (part number
RCKMNT-1RU=) to the switch. See Figure 2-13, Figure 2-14, and
Figure 2-15.
Figure 2-1 to Figure 2-15 show how to attach a bracket to one side of the switch.
Follow the same steps to attach the second bracket to the opposite side of the
switch.
Catalyst 2950 Desktop Switch Hardware Installation Guide
2-10
78-11157-03
Chapter 2
Installation
Installing the Switch in a Rack
Figure 2-1
Attaching Brackets on the Switch in a 19-Inch Rack (Front Panel
Forward)
SYST
RPS
STAT
1x
2x
3x
UTIL DU
PLX SP
EED
4x
5x
45580
MODE
Number-8
Phillips flat-head
screws
Figure 2-2
Attaching Brackets on the Switch in a 19-Inch Rack (Rear Panel
Forward)
CONSOL
Number-8
Phillips flat-head
screws
52916
E
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
2-11
Chapter 2
Installation
Installing the Switch in a Rack
Figure 2-3
Attaching Brackets on the Switch in a 19-Inch Telco Rack
CONSOL
E
Figure 2-4
45582
Number-8
Phillips flat-head
screws
Attaching Brackets on the Catalyst 2950G-48-EI Switch in a 19-Inch
Rack (Front Panel Forward)
1
SYST
RPS
1X
STAT
UTIL
DUPLX
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
SPEED
MODE
15X
2X
Number-8
Phillips
flat-head
screws
65512
16X
Catalyst 2950 Desktop Switch Hardware Installation Guide
2-12
78-11157-03
Chapter 2
Installation
Installing the Switch in a Rack
Figure 2-5
Attaching Brackets on the Catalyst 2950G-48-EI Switch in a 19-Inch Rack (Rear Panel
Forward)
CONSO
LE
Attaching Brackets on the Catalyst 2950G-48-EI Switch in a 19-Inch Telco Rack
CONSOL
E
Number-8
Phillips
flat-head
screws
65514
Figure 2-6
65513
Number-8
Phillips
flat-head
screws
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
2-13
Chapter 2
Installation
Installing the Switch in a Rack
Attaching Brackets on the Catalyst 2950G-24-EI-DC Switch in a
23-Inch Telco Rack (Front Panel Forward)
1
SYST
1X
RPS
STAT
Number-8
Phillips
truss-head
screws
Figure 2-8
3
4
5
6
7
8
9
10
UTIL DU
PLX SP
EED
11
12
11X
MODE
2X
12X
Attaching Brackets on the Catalyst 2950G-24-EI-DC Switch in a 23-Inch Telco Rack
(Rear Panel Forward)
LE
Number-8
Phillips
truss-head
screws
65674
CONSO
2
65673
Figure 2-7
Catalyst 2950 Desktop Switch Hardware Installation Guide
2-14
78-11157-03
Chapter 2
Installation
Installing the Switch in a Rack
Figure 2-9
Attaching Brackets on the Catalyst 2950G-24-EI-DC Switch in a 23-Inch Telco Rack
CONSOL
E
65675
Number-8
Phillips
truss-head
screws
Figure 2-10 Attaching Brackets on the Switch in a 24-Inch Rack (Front Panel
Forward)
1
SYST
1X
RPS
Number-8
Phillips
truss-head
screws
3
4
5
6
7
8
9
10
11
UTIL DU
PLX SP
EED
12
11X
MODE
2X
12X
65666
STAT
2
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
2-15
Chapter 2
Installation
Installing the Switch in a Rack
Figure 2-11 Attaching Brackets on the Switch in a 24-Inch Rack (Rear Panel
Forward)
LE
Number-8
Phillips
truss-head
screws
65665
CONSO
Catalyst 2950 Desktop Switch Hardware Installation Guide
2-16
78-11157-03
Chapter 2
Installation
Installing the Switch in a Rack
Figure 2-12 Attaching Brackets on the Switch in a 24-Inch Telco Rack
CONSOL
E
65667
Number-8
Phillips
truss-head
screws
Figure 2-13 Attaching Brackets on the Catalyst 2950G-48-EI Switch in a 24-Inch
Rack (Front Panel Forward)
1
SYST
RPS
1X
STAT
UTIL
2
3
4
5
6
7
8
9
10
11
DUPLX
SPEED
12
13
14
15
16
15X
2X
16X
74528
Phillips
flat-head
screws
MODE
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
2-17
Chapter 2
Installation
Installing the Switch in a Rack
Figure 2-14 Attaching Brackets on the Catalyst 2950G-48-EI Switch in a 24-Inch
Rack (Rear Panel Forward)
Phillips
flat-head
screws
74529
CONSO
LE
Figure 2-15 Attaching Brackets on the Catalyst 2950G-48-EI Switch in a 24-Inch
Telco Rack
33
33X
34
35
36
37
38
39
40
41
42
43
44
45
46
47
Catalyst 295
0 SERIES
48
47X
34X
1
48X
2
Phillips
flat-head
screws
74530
24" Configuration
Catalyst 2950 Desktop Switch Hardware Installation Guide
2-18
78-11157-03
Chapter 2
Installation
Installing the Switch in a Rack
Mounting the Switch in a Rack
After attaching the brackets, use the four Phillips machine screws to securely
attach the brackets to the rack, as shown in Figure 2-16.
To prevent the cables from obscuring the switch and other devices in the rack, you
can also attach the cable guide to the rack. See the“Attaching the Optional Cable
Guide” section for instructions.
Figure 2-16 Mounting the Switch in a Rack
RPS
UTIL DUPLX
SPEED
1x
2x
3x
4x
5x
6x
MODE
7x
8x
9x
10x
11x
10Base-T
/ 100BaseTX
12x
13x
14x
15x
16x
17x
18x
19x
20x
21x
Catalyst 295
0
22x
23x
SERIES
24x
45572
SYST
STAT
Number-12
Phillips machine
screws
After mounting the switch in the rack, start the terminal-emulation software, and
provide power to the switch. See the “Powering On the Switch” section on
page 2-22 for instructions.
Attaching the Optional Cable Guide
We recommend attaching the cable guide to prevent the cables from obscuring the
front panels of the switch and other devices installed in the rack. Use the supplied
black Phillips machine screw to attach the cable guide to the left or right bracket,
as shown in Figure 2-17.
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
2-19
Chapter 2
Installation
Installing the Switch on a Table, Shelf, or Desk
Figure 2-17 Attaching the Cable Guide
SYST
RPS
STAT
UTIL DUPLX
1x
2x
SPEED
3x
4x
5x
6x
7x
8x
9x
10x
11x
10Base-T
/ 100Base-T
X
12x
13x
14x
15x
16x
17x
18x
19x
20x
Catalyst 2950
21x
22x
23x
SERIES
24x
45573
MODE
Cable guide screw
Installing the Switch on a Table, Shelf, or Desk
Before placing the switch on a table, shelf, or desk, locate the adhesive strip with
rubber feet in the mounting-kit envelope, and attach four rubber feet to the
recessed areas on the switch bottom. Place the switch on a table, shelf, or desk
near an AC power source or DC-input power source.
Start the terminal-emulation software and provide power to the switch. See the
“Powering On the Switch” section for instructions.
Installing the GBIC Modules
Figure 2-18, Figure 2-19, and Figure 2-20 show how to insert a GBIC module in
a GBIC module slot on the switch. For instructions about how to install a CWDM
GBIC module in a GBIC module slot, refer to the documentation that came with
that GBIC module.
For detailed instructions on installing, removing, and cabling the GBIC module
(the 1000BASE-X module, the 1000BASE-T module, the CWDM GBIC module,
or the GigaStack module), refer to your GBIC documentation.
Catalyst 2950 Desktop Switch Hardware Installation Guide
2-20
78-11157-03
Chapter 2
Installation
Installing the GBIC Modules
Caution
To prevent electrostatic-discharge (ESD) damage when installing GBIC modules,
follow your normal board and component handling procedures.
Figure 2-18 Installing a 1000BASE-X GBIC Module in a Switch
Metal flap door
Catalyst 29
50
1
SERIES
GBIC module slot
1000BASE-X
GBIC module
74532
2
Figure 2-19 Installing a 1000BASE-T GBIC Module in a Switch
Metal flap door
1
Catalyst 29
50
SERIES
1000BASE-T
GBIC module
GBIC module slot
74531
2
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
2-21
Chapter 2
Installation
Powering On the Switch
Figure 2-20 Installing a GigaStack GBIC Module in a Switch
Metal flap door
1
Catalyst 29
50
SERIES
GigaStack
GBIC module
GBIC module slot
74533
2
Powering On the Switch
Before connecting the AC power cord, a DC-input power source, or the
Redundant Power System (RPS) to the switch, make sure that you have started the
terminal-emulation software (such as ProComm, HyperTerminal, tip, or minicom)
from your management station.
If you are using the AC power cord, connect the AC power cord to the AC power
connector and to an AC power outlet.
If you are using the DC-input power source, see the “Connecting to DC Power”
section for installation instructions.
If you are using an RPS, refer to the documentation that came with your RPS for
installation instructions.
Warning
Attach only the Cisco RPS 300 (model PWR300-AC-RPS-N1) to the RPS
receptacle.
For POST information, see the “Running POST” section on page 2-32.
Catalyst 2950 Desktop Switch Hardware Installation Guide
2-22
78-11157-03
Chapter 2
Installation
Connecting to DC Power
Connecting to DC Power
To connect the Catalyst 2950G-24-EI-DC switch to a DC-input power source,
follow these steps:
•
Preparing for Installation, page 2-23
•
Grounding the Switch, page 2-24
•
Wiring the DC-Input Power Source, page 2-26
Warning
The Catalyst 2950G-24-EI-DC contains no field-replaceable units (FRUs). Do not
open the chassis or attempt to remove or replace any components. For
information about obtaining service for this unit, contact your reseller or Cisco
sales representative.
Warning
The equipment is to be installed in a restricted access area.
Warning
Ethernet cables must be shielded when used in a central office environment.
Preparing for Installation
Locate the DC terminal block plug, the ground lug, and the two number-10-32
screws in the DC-switch kit.
Obtain these necessary tools and equipment:
•
Ratcheting torque screwdriver with a Phillips head that exerts up to
15 pound-force inches (lbf-in.) of pressure
•
Panduit crimping tool with optional controlled cycle mechanism
(model CT-700, CT-720, CT-920, CT-920CH, CT-930, or CT-940CH)
•
6-gauge copper ground wire (insulated or noninsulated)
•
Four leads of 18-gauge copper wire
•
Wire-stripping tools for stripping 6- and 18-gauge wires
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
2-23
Chapter 2
Installation
Connecting to DC Power
Grounding the Switch
Warning
This equipment is intended to be grounded. Ensure that the host is connected to
earth ground during normal use.
Warning
When installing the unit, always make the ground connection first and
disconnect it last.
Caution
To make sure that the equipment is reliably connected to earth ground, follow the
grounding procedure instructions, and use a UL-listed lug suitable for number-6
AWG wire and two number-10-32 ground-lug screws.
To ground the switch to earth ground, follow these steps. Make sure to follow any
grounding requirements at your site.
Step 1
Locate the ground lug and the two number-10-32 screws from the switch rear
panel. Use a standard Phillips screwdriver or a ratcheting torque screwdriver with
a Phillips head. Set the screws and the ground lug aside.
Step 2
If your ground wire is insulated, use a wire stripping tool to strip the 6-gauge
ground wire to 0.5 inch (12.7 millimeter [mm]) ± 0.02 inch (0.5 mm) as shown in
Figure 2-21.
Figure 2-21 Stripping the Ground Wire
Insulation
Step 3
Wire lead
60528
0.5 in. (12.7 mm) ± 0.02 in. (0.5 mm)
Slide the open end of the ground lug over the exposed area of the 6-gauge wire.
Catalyst 2950 Desktop Switch Hardware Installation Guide
2-24
78-11157-03
Chapter 2
Installation
Connecting to DC Power
Step 4
Using a Panduit crimping tool, crimp the ground lug to the 6-gauge wire.
60529
Figure 2-22 Crimping the Ground Lug
Step 5
Use the two number-10-32 screws to attach the ground lug and wire assembly to
the switch rear panel.
Step 6
Using a ratcheting torque screwdriver, torque each ground-lug screw to 15 lbf-in.
(240 ounce-force inches [ozf-in.]).
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
2-25
Chapter 2
Installation
Connecting to DC Power
Figure 2-23 Torquing Ground-Lug Screws
36 - 72V
1 - 0.5A
A
B
DC INPUT
FO
POWE R REMOTE
SPECIF R SUPPLY
IED IN
+12V @4MANUAL.
.5A
65295
CONSOLE
Torque to 15 lbf-in.
Wiring the DC-Input Power Source
Warning
Only trained and qualified personnel should be allowed to install or replace this
equipment.
Warning
Before performing any of the following procedures, ensure that power is
removed from the DC circuit. To ensure that all power is OFF, locate the circuit
breaker on the panel board that services the DC circuit, switch the circuit
breaker to the OFF position, and tape the switch handle of the circuit breaker in
the OFF position.
Catalyst 2950 Desktop Switch Hardware Installation Guide
2-26
78-11157-03
Chapter 2
Installation
Connecting to DC Power
Caution
You must connect the Catalyst 2950G-24-EI-DC switch only to a DC-input power
source that has an input supply voltage from –36 to –72 VDC. If the supply
voltage is not in this range, the switch might not operate properly or might be
damaged.
Caution
The switch must be installed with 5A-branch-circuit protection.
Note
This installation must comply with all applicable codes.
To wire the switch to a DC-input power source, follow these steps:
Step 1
Locate the terminal block plug (see Figure 2-24).
60530
Figure 2-24 Terminal Block Plug
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
2-27
Chapter 2
Installation
Connecting to DC Power
Step 2
Identify the positive and negative feed positions for the terminal block
connection. The wiring sequence is positive to positive and negative to negative
for both the A and the B feed wires. The switch rear panel identifies the positive
and negative positions for both the A and B feed wires.
Figure 2-25 Positive and Negative Positions on the Switch Rear Panel
36 - 72V
1 - 0.5A
A
65292
B
Step 3
Using an 18-gauge wire-stripping tool, strip each of the four wires coming from
the DC-input power source to 0.27 inch (6.6 mm) ± 0.02 inch (0.5 mm). Do not
strip more than 0.29 inch (7.4 mm) of insulation from the wire. Stripping more
than the recommended amount of wire can leave exposed wire from the terminal
block plug after installation.
Figure 2-26 Stripping the DC-Input Power Source Wire
60531
0.27 inch (6.6 mm) ± 0.02 inch (0.5 mm)
Step 4
Insert the exposed wire of one of the four DC-input power source wires into the
terminal block plug, as shown in Figure 2-27. Make sure that you cannot see any
wire lead. Only wire with insulation should extend from the terminal block.
Catalyst 2950 Desktop Switch Hardware Installation Guide
2-28
78-11157-03
Chapter 2
Installation
Connecting to DC Power
Warning
An exposed wire lead from a DC-input power source can conduct harmful levels
of electricity. Be sure that no exposed portion of the DC-input power source
wire extends from the terminal block plug.
Figure 2-27 Inserting Wires in the Terminal Block Plug
Feed A
Feed B
60532
Return
Negative
Return
Negative
Step 5
Caution
Use a ratcheting torque screwdriver to torque the terminal block captive screw
(above the installed wire lead) to 4.5 lbf-in. (72 ozf-in.). (See Figure 2-28.)
Do not overtorque the terminal-block captive screws. The recommended
maximum torque is 4.5 lbf-in.
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
2-29
Chapter 2
Installation
Connecting to DC Power
Figure 2-28 Torquing the Terminal-Block Captive Screws
60533
Torque to 4.5 lbf-in. (72 ozf-in.)
Catalyst 2950 Desktop Switch Hardware Installation Guide
2-30
78-11157-03
Chapter 2
Installation
Connecting to DC Power
Step 6
Repeat Steps 4 and 5 for the remaining three DC-input power source wires.
Figure 2-29 shows the completed wiring of a terminal block plug.
Figure 2-29 Completed Wiring of Terminal Block Plug
Feed A
Feed B
60534
Return
Negative
Return
Negative
Step 7
Insert the terminal block plug in the terminal block header on the switch rear panel
(see Figure 2-30).
Caution
Secure the wires coming in from the terminal block so that they cannot be
disturbed by casual contact. For example, use tie wraps to secure the wires to the
rack.
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
2-31
Chapter 2
Installation
Running POST
Figure 2-30 Inserting the Terminal Block in the Block Header
36 - 72V
1 - 0.5A
DC INPUT
FO
POWE R REMOTE
SPECIF R SUPPLY
IED IN
+12V @4MANUAL.
.5A
A
B
65293
CONSOLE
Tie wrap
Step 8
Remove the tape from the circuit-breaker switch handle, and move the
circuit-breaker handle to the on position.
Running POST
After the power is connected, the switch automatically begins POST, a series of
tests that verifies that the switch functions properly. When the switch begins
POST, the system LED is off. If POST completes successfully, the LED turns
green. If POST fails, the LED turns amber. See Chapter 3, “Troubleshooting,” to
determine a corrective action.
Note
POST failures are usually fatal. Call Cisco Systems immediately if your switch
does not pass POST.
Catalyst 2950 Desktop Switch Hardware Installation Guide
2-32
78-11157-03
Chapter 2
Installation
Connecting to 10/100 and 10/100/1000 Ports
Connecting to 10/100 and 10/100/1000 Ports
The 10/100 ports configure themselves to operate at the speed and duplex settings
of attached devices.They operate at 10 or 100 Mbps in half- or full-duplex mode.
If the attached devices do not support autonegotiation, you can explicitly set the
speed and duplex parameters.
The 10/100/1000 ports configure themselves to operate at the speed setting of
attached devices.These ports on Catalyst 2950T-24 switches operate at 10, 100, or
1000 Mbps only in full-duplex mode. If the attached devices do not support
autonegotiation, you can explicitly set the speed parameter.
Connecting devices that do not autonegotiate or devices with manually set speed
and duplex parameters can reduce performance or result in link failures between
the devices. To maximize performance, choose one of these methods for
configuring the ports:
•
Let the ports autonegotiate both speed and duplex for 10/100 ports and only
speed for 10/100/1000 ports.
•
Set the speed and duplex parameters on both ends of the connection.
When connecting the ports on the Catalyst 2950G-24-EI-DC switches to other
devices, follow these guidelines:
Caution
To comply with the intrabuilding lightning surge requirements, intrabuilding
wiring must be shielded, and the shield for the wiring must be grounded at both
ends.
Caution
The Catalyst 2950G-24-EI-DC switch is suitable only for intrabuilding or
nonexposed wiring connections.
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
2-33
Chapter 2
Installation
Connecting to 10/100 and 10/100/1000 Ports
Follow these steps to connect the switch to 10BASE-T, 100BASE-TX, or
1000BASE-T devices:
Caution
To prevent electrostatic-discharge (ESD) damage, follow your normal board and
component handling procedures.
Step 1
When connecting to servers, workstations, and routers, insert a twisted-pair
straight-through cable in a front-panel RJ-45 connector, as shown in Figure 2-31,
Figure 2-32, and Figure 2-33. When connecting to switches or repeaters, insert a
twisted-pair crossover cable. (See the “Cable and Adapter Specifications” section
on page B-7 for cable-pinout descriptions.)
Note
When connecting to 1000BASE-T devices, be sure to use a four twisted-pair,
Category 5 cable.
Figure 2-31 Connecting to a Port on Catalyst 2950-12, 2950-24, 2950C-24,
2950SX-24, and 2950T-24 Switches
SYST
RPS
STAT
1x
2x
3x
4x
UTIL DU
PLX SP
EED
5x
45576
MODE
Catalyst 2950 Desktop Switch Hardware Installation Guide
2-34
78-11157-03
Chapter 2
Installation
Connecting to 10/100 and 10/100/1000 Ports
Figure 2-32 Connecting to a Port on Catalyst 2950G-12-EI, 2950G-24-EI, and
2950G-24-EI-DC Switches
1
1X
RPS
STAT
2
3
4
5
6
7
8
9
10
11
UTIL D
UPLX S
PEED
MODE
12
11X
2X
12X
65394
SYST
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
2-35
Chapter 2
Installation
Connecting to 10/100 and 10/100/1000 Ports
Figure 2-33 Connecting to a Port on Catalyst 2950G-48-EI Switches
1
SYST
RPS
2
3
4
1X
5
6
7
STAT
UTIL
DUPLX
8
9
10
11
12
13
14
15
16
SPEED
15X
2X
16X
Step 2
Insert the other cable end in an RJ-45 connector on the target device.
Step 3
Observe the port status LED.
65517
MODE
The LED turns green when the switch and the target device have an established
link.
The LED turns amber while Spanning Tree Protocol (STP) discovers the network
topology and searches for loops. This process takes about 30 seconds, and then
the LED turns green.
If the LED is off, the target device might not be turned on, there might be a cable
problem, or there might be a problem with the adapter installed in the target
device. See Chapter 3, “Troubleshooting,” for solutions to cabling problems.
Step 4
Reconfigure and restart the target device if necessary.
Step 5
Repeat Steps 1 through 4 to connect each port.
Catalyst 2950 Desktop Switch Hardware Installation Guide
2-36
78-11157-03
Chapter 2
Installation
Connecting to 100BASE-FX and 1000BASE-SX Ports
Connecting to 100BASE-FX and 1000BASE-SX Ports
The 100BASE-FX and 1000BASE-SX ports operate only in full-duplex mode.
You can connect a 100BASE-FX or 1000BASE-SX port to an SC or ST port on
another device by using one of the MT-RJ fiber-optic patch cables listed in
Table 2-1. Use the Cisco part numbers in Table 2-1 to order the patch cables that
you need.
Follow these steps to connect the switch to a 100BASE-FX or 1000BASE-SX
device:
Do not remove the dust plugs from the fiber-optic ports or the rubber caps from
the fiber-optic cable until you are ready to connect the cable. The plugs and caps
protect the fiber-optic ports and cables from contamination and ambient light.
Caution
Step 1
Remove the dust plugs from the 100BASE-FX or 1000BASE-SX port and the
rubber caps from the MT-RJ patch cable. Store them for future use.
Step 2
Insert the cable in a 100BASE-FX or 1000BASE-SX port. (See Figure 2-34.)
SYST
RPS
STAT
UTIL DUPLX
1x
2x
3x
SPEED
MODE
4x
5x
6x
7x
8x
9x
10x
11x
10Base-T
/ 100BaseTX
12x
13x
14x
15x
16x
17x
18x
19x
MT-RJ
patch cable
20x
21x
Catalyst 295
0 SERIE
S
22x
23x
24x
100BaseFX
25
45571
Figure 2-34 Connecting to a 100BASE-FX or 1000BASE-SX Port
26
Dust plug
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
2-37
Chapter 2
Installation
Connecting to GBIC Module Ports
Step 3
Insert the other cable end in an SC or ST port on the target device.
Step 4
Observe the port status LED.
The LED turns green when the switch and the target device have an established
link.
The LED turns amber while STP discovers the network topology and searches for
loops. This process takes about 30 seconds, and then the port LED turns green.
If the LED is off, the target device might not be turned on, there might be a cable
problem, or there might be a problem with the adapter installed in the target
device. See Chapter 3, “Troubleshooting,” for solutions to cabling problems.
Step 5
Reconfigure and restart the target device if necessary.
Step 6
Repeat Steps 1 through 5 to connect each port.
Connecting to GBIC Module Ports
These sections describe how to connect to a GBIC module port.
•
Connecting to 1000BASE-X GBIC Module Ports, page 2-39
•
Connecting to 1000BASE-T GBIC Module Ports, page 2-41
•
Connecting to GigaStack GBIC Module Ports, page 2-42
For instructions about how to connect to the CWDM GBIC module ports, refer to
the documentation that came with that GBIC module.
For detailed instructions about installing, removing, and connecting to the GBIC
module (the 1000BASE-X module, the 1000BASE-T module, the CWDM GBIC
module, or the GigaStack module), refer to the GBIC documentation.
Catalyst 2950 Desktop Switch Hardware Installation Guide
2-38
78-11157-03
Chapter 2
Installation
Connecting to GBIC Module Ports
When connecting the ports on the Catalyst 2950G-24-EI-DC switches to other
devices, follow these guidelines:
Caution
To comply with the intrabuilding lightning surge requirements, intrabuilding
wiring must be shielded, and the shield for the wiring must be grounded at both
ends.
Caution
The Catalyst 2950G-24-EI-DC switch is suitable only for intrabuilding or
nonexposed wiring connections.
Connecting to 1000BASE-X GBIC Module Ports
Caution
Do not remove the rubber plugs from the GBIC module port or the rubber caps
from the fiber-optic cable until you are ready to connect the cable. The plugs and
caps protect the GBIC module ports and cables from contamination and ambient
light.
After installing the 1000BASE-X GBIC in the GBIC module slot, follow these
steps:
Step 1
Remove the rubber plugs from the GBIC module port, and store them for future
use.
Step 2
Insert the SC connector in the fiber-optic receptacle (see Figure 2-35).
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
2-39
Chapter 2
Installation
Connecting to GBIC Module Ports
Figure 2-35 Connecting to a 1000 BASE-X GBIC Port
1
Catalyst 29
50 SERIES
65296
2
Step 3
Insert the other cable end in a fiber-optic receptacle on a target device.
Step 4
Observe the port status LED.
The LED turns green when the switch and the target device have an established
link.
The LED turns amber while STP discovers the network topology and searches for
loops. This process takes about 30 seconds, and then the port LED turns green.
If the LED is off, the target device might not be turned on, there might be a cable
problem, or there might be problem with the adapter installed in the target device.
See Chapter 3, “Troubleshooting,” for solutions to cabling problems.
Step 5
Reconfigure and restart the switch or target device if necessary.
Catalyst 2950 Desktop Switch Hardware Installation Guide
2-40
78-11157-03
Chapter 2
Installation
Connecting to GBIC Module Ports
Connecting to 1000BASE-T GBIC Module Ports
After installing the 1000BASE-T GBIC in the GBIC module slot, follow these
steps:
Caution
Step 1
Note
To prevent ESD damage, follow your normal board and component handling
procedures.
When connecting to servers, workstations, and routers, insert a four twisted-pair,
straight-through cable in the RJ-45 connector. When connecting to switches or
repeaters, insert a four twisted-pair, crossover cable (see Figure 2-36).
When connecting to a 1000BASE-T device, be sure to use a four twisted-pair,
Category 5 cable.
Figure 2-36 Connecting to a 1000BASE-T GBIC Port
1
Catalyst 29
50 SERIES
65297
2
Step 2
Insert the other cable end in an RJ-45 connector on a target device.
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
2-41
Chapter 2
Installation
Connecting to GBIC Module Ports
Step 3
Observe the port status LED.
The LED turns green when the switch and the target device have an established
link.
The LED turns amber while STP discovers the network topology and searches for
loops. This process takes about 30 seconds, and then the LED turns green.
If the LED is off, the target device might not be turned on, there might be a cable
problem, or there might be a problem with the adapter installed in the target
device. See Chapter 3, “Troubleshooting,” for solutions to cabling problems.
Step 4
Reconfigure and restart the switch or target device, if necessary.
Connecting to GigaStack GBIC Module Ports
After installing the GigaStack GBIC in the GBIC module slot, follow these steps:
Step 1
Insert the GigaStack cable connector in the GBIC (see Figure 2-37).
Figure 2-37 Connecting to a GigaStack GBIC Port
1
Catalyst 29
50 SERIES
65298
2
Step 2
Insert the other cable end in a port on a target device.
Catalyst 2950 Desktop Switch Hardware Installation Guide
2-42
78-11157-03
Chapter 2
Installation
Connecting a PC or a Terminal to the Console Port
Step 3
Observe the port status LED.
The LED turns green when the switch and the target device have an established
link.
The LED turns amber while STP discovers the network topology and searches for
loops. This process takes about 30 seconds, and then the port LED turns green.
If the LED is off, the target device might not be turned on, there might be a cable
problem, or there might be a problem with the adapter installed in the target
device. See Chapter 3, “Troubleshooting,” for solutions to cabling problems.
Step 4
Reconfigure and restart the switch or target device, if necessary.
Connecting a PC or a Terminal to the Console Port
If you want to connect a PC to the console port, use the supplied RJ-45-to-DB-9
adapter cable. If you want to connect a terminal to the console port, you need to
provide an RJ-45-to-DB-25 female DTE adapter. You can order a kit (part number
ACS-DSBUASYN=) with that adapter from Cisco. For console-port and
adapter-pinout information, see the“Cable and Adapter Specifications” section on
page B-7.
The PC or terminal must support VT100 terminal emulation. The
terminal-emulation software—frequently a PC application such as
HyperTerminal or Procomm Plus—makes communication between the switch and
your PC or terminal possible during the setup program.
Follow these steps to connect your PC or terminal to the console port:
Step 1
Make sure that your terminal-emulation software is configured to communicate
with the switch through hardware flow control.
Step 2
Configure the baud rate and character format of the PC or terminal to match these
console-port default characteristics:
•
9600 baud
•
Eight data bits
•
One stop bit
•
No parity
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
2-43
Chapter 2
Installation
Connecting a PC or a Terminal to the Console Port
After gaining access to the switch, you can change the port baud rate. Refer to the
switch software configuration guide for instructions.
Step 3
Insert the adapter cable in the console port, as shown in Figure 2-38, Figure 2-39,
and Figure 2-40. (See the “Cable and Adapter Pinouts” section on page B-10 for
pinout descriptions.)
RATING
100-127V~
@ 1A
200-240V~
@0.5A
50-60Hz
DC INPUT
FO
POWE R REMOTE
SPECIF R SUPPLY
IED IN
+12V @4MANUAL.
.5A
CONSOLE
74589
Figure 2-38 Connecting to the Console Port
RJ-45-to-DB-9
adapter cable
36 - 72V
1 - 0.5A
A
B
DC INPUT
FO
POWE R REMOTE
SPECIF R SUPPLY
IED IN
+12V @4MANUAL.
.5A
CONSOLE
74590
Figure 2-39 Connecting to a Console Port Only on Catalyst 2950G-24-EI-DC Switches
RJ-45-to-DB-9
adapter cable
Catalyst 2950 Desktop Switch Hardware Installation Guide
2-44
78-11157-03
Chapter 2
Installation
Where to Go Next
Figure 2-40 Connecting to a Console Port Only on Catalyst 2950G-48-EI Switches
200-240V~
@0.5A
50-60Hz
DC INPUT
FO
POWE R REMOTE
SPECIF R SUPPLY
IED IN
+12V @4MANUAL.
.5A
74591
RATING
100-127V~
@ 1A
CONSOLE
RJ-45-to-DB-9
adapter cable
Step 4
Attach the appropriate adapter to the terminal, if needed.
Step 5
Insert the other adapter cable end in the PC or terminal adapter.
Step 6
Start the terminal-emulation software.
Where to Go Next
For information about starting up the switch, refer to the Release Notes for the
Catalyst 2950 Switch.
For information about configuring the switch, refer to the switch software
configuration guide.
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
2-45
Chapter 2
Installation
Where to Go Next
Catalyst 2950 Desktop Switch Hardware Installation Guide
2-46
78-11157-03
C H A P T E R
3
Troubleshooting
The front-panel LEDs provide troubleshooting information about the switch.
They show power-on self-test (POST) failures, port-connectivity problems, and
overall switch performance. For a full description of the LEDs, see the “LEDs”
section on page 1-9.
You can also get statistics from the Cluster Management Suite (CMS), the
command-line interface (CLI), the Cisco Intelligence Engine 2100 (IE2100)
Series Configuration Registrar, or a Simple Network Management Protocol
(SNMP) workstation. Refer to the switch software configuration guide, the switch
command reference, or the documentation that came with your IE2100 or SNMP
application for details.
This chapter provides these topics for troubleshooting problems:
•
Understanding POST Results, page 3-2
•
Diagnosing Problems, page 3-2
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
3-1
Chapter 3
Troubleshooting
Understanding POST Results
Understanding POST Results
While the switch powers on, it automatically begins POST, a series of tests that
verifies that the switch functions properly. When the switch begins POST, the
system LED is off. If POST completes successfully, the LED turns green. If POST
fails, the LED turns amber.
Note
POST failures are usually fatal. Call Cisco Systems if your switch does not pass
POST.
Diagnosing Problems
Common switch problems fall into these categories:
•
Poor performance
•
No connectivity
•
Corrupted software
Table 3-1 describes how to detect and solve these problems.
Catalyst 2950 Desktop Switch Hardware Installation Guide
3-2
78-11157-03
Chapter 3
Troubleshooting
Diagnosing Problems
Table 3-1
Common Problems and Solutions
Symptom
Possible Cause
Resolution
Poor performance or
excessive errors.
Duplex autonegotiation mismatch.
Refer to the switch software
configuration guide for
information about identifying
autonegotiation mismatches.
Cabling distance exceeded.
•
Port statistics show excessive
frame check sequence (FCS),
late-collision, or alignment
errors.
•
For 10BASE-T, 100BASE-TX,
and 1000BASE-T connections:
– The distance between the
port and the attached device
exceeds 328 feet
(100 meters).
– If the switch is attached to a
•
Refer to the switch software
configuration guide for
information about
displaying port statistics.
•
Reduce cable length to
within the recommended
distances.
•
Refer to your repeater
documentation for cabling
guidelines.
•
Refer to your GBIC module
documentation for cabling
guidelines.
•
Run adapter card diagnostic
utility.
repeater, the total distance
between the two end
stations exceeds the cabling
guidelines.
•
For GBIC module port
connections: The distance
between the GBIC module port
and the attached device exceeds
the GBIC cabling guidelines.
Bad adapter in attached device.
•
Excessive errors found in port
statistics.
Spanning Tree Protocol (STP)
checking for possible loops.
Wait 30 seconds for port status
LED to turn green.
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
3-3
Chapter 3
Troubleshooting
Diagnosing Problems
Table 3-1
Common Problems and Solutions (continued)
Symptom
Possible Cause
No connectivity.
Incorrect or bad cable.
Resolution
No link at both ends.
•
A crossover cable was used
when a straight-through was
required, or vice-versa.
•
For the correct pinouts and
the proper application of
crossover vs.
straight-through cables, see
the “Cable and Adapter
Specifications” section on
page B-7.
•
The cable is wired incorrectly.
•
Replace it with a tested
good cable.
•
STP checking for possible
loops.
•
Wait 30 seconds for port
status LED to turn green.
Switch not recognizing a GBIC
module.
Refer to your GBIC module
documentation for more
information.
Unreadable characters on
the management console.
Incorrect baud rate.
Reset the terminal-emulation
software to 9600 baud.
System LED is amber, and
all port LEDs are off.
Corrupted software.
Attach a monitor to the serial
port to display the switch boot
loader. For more information,
refer to the switch software
configuration guide.
Catalyst 2950 Desktop Switch Hardware Installation Guide
3-4
78-11157-03
Chapter 3
Troubleshooting
Diagnosing Problems
Table 3-1
Common Problems and Solutions (continued)
Symptom
System LED is amber
Possible Cause
•
Internal fan fault detected.
Resolution
•
Check if the fan has failed
by using the show env fan
privileged EXEC command.
If the fan has failed, call
Cisco Systems.
•
Switch placed in
error-disabled state after
GBIC module is inserted
Nonfatal or fatal POST error
detected.
Bad or non-Cisco-approved GBIC
module.
•
Use the show post
privileged EXEC command
to see which POST test
failed.
Remove GBIC module from the
switch, and replace it with a
Cisco-approved module. Use the
errdisable recovery cause
gbic-invalid global
configuration command to
verify port status, and enter a
time interval to recover from the
error-disable state.
Refer to the switch software
configuration guide for
information about the
errdisable recovery command.
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
3-5
Chapter 3
Troubleshooting
Diagnosing Problems
Catalyst 2950 Desktop Switch Hardware Installation Guide
3-6
78-11157-03
A P P E N D I X
A
Technical Specifications
Table A-1, Table A-2, Table A-3, and Table A-4 list the technical specifications
for the Catalyst 2950 switches. Table A-5 and Table A-6 list the regulatory
agency approvals.
Table A-1
Technical Specifications for Catalyst 2950-12, 2950-24, 2950C-24,
2950SX-24, and 2950T-24 Switches
Environmental Ranges
Operating temperature
32 to 113°F (0 to 45°C)
Storage temperature
–13 to 158°F (–25 to 70°C)
Operating humidity
10 to 85% (noncondensing)
Operating altitude
Up to 10,000 ft (3000 m)
Storage altitude
Up to 15,000 ft (4570 m)
Power Requirements
AC input voltage
100 to 127/200 to 240 VAC
(autoranging) 50 to 60 Hz
DC input voltages for the Cisco +12V
RPS 300 Redundant Power
System (RPS)
Power consumption
@4.5A
30W (maximum)
102 Btus per hour
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
A-1
Appendix A
Table A-1
Technical Specifications
Technical Specifications for Catalyst 2950-12, 2950-24, 2950C-24,
2950SX-24, and 2950T-24 Switches (continued)
Physical Dimensions
Weight
6.5 lb (3 kg)
Dimensions
(H x W x D)
1.72 x 17.5 x 9.52 in.
(4.36 x 44.45 x 24.18 cm)
Table A-2
Technical Specifications for Catalyst 2950G-12-EI, 2950G-24-EI, and
2950G-48-EI Switches
Catalyst 2950G-12-EI and
2950G-24-EI Switches
Catalyst 2950G-48-EI
Switch
Environmental Ranges
Operating
temperature
32 to 113°F
(0 to 45°C)
32 to 113°F
(0 to 45°C)
Storage
temperature
–13 to 158°F
(–25 to 70°C)
–13 to 158°F
(–25 to 70°C)
Operating
humidity
10 to 85% (noncondensing)
10 to 85%
(noncondensing)
Operating
altitude
Up to 10,000 ft (3000 m)
Up to 10,000 ft (3000 m)
Storage altitude
Up to 15,000 ft (4570 m)
Up to 15,000 ft (4570 m)
Power Requirements
AC input voltage 100 to 127/200
to 240 VAC (autoranging)
50 to 60 Hz
100 to 127/200
to 240 VAC (autoranging)
50 to 60 Hz
DC input
voltage for the
Cisco RPS 300
+12V
+12V
Power
consumption
30W (maximum)
45W (maximum)
102 Btus per hour
154 Btus per hour
@4.5A
@4.5A
Catalyst 2950 Desktop Switch Hardware Installation Guide
A-2
78-11157-03
Appendix A
Technical Specifications
Table A-2
Technical Specifications for Catalyst 2950G-12-EI, 2950G-24-EI, and
2950G-48-EI Switches (continued)
Catalyst 2950G-12-EI and
2950G-24-EI Switches
Catalyst 2950G-48-EI
Switch
Weight
6.5 lb (3 kg)
10.5 lb (4.8 kg)
Dimensions
(H x W x D)
1.72 x 17.5 x 9.52 in.
(4.36 x 44.45 x 24.18 cm)
1.72 x 17.5 x 13 in.
(4.36 x 44.45 x 33.02 cm)
Physical Dimensions
Table A-3
Technical Specifications for Catalyst 2950G-24-EI-DC Switch
Environmental Ranges
Operating temperature
32 to 113°F (0 to 45°C)
Storage temperature
–13 to 158°F (–25 to 70°C)
Operating humidity
10 to 85% (noncondensing)
Operating altitude
Up to 10,000 ft (3000 m)
Storage altitude
Up to 15,000 ft (4570 m)
Power Requirements
Power consumption
30W
DC input voltage
–36 to –72 VDC
Wire gauge for power connection
18 AWG1 (6 AWG for protective
earth)
Branch circuit protection
5A
Physical Dimensions
Weight
6.5 lb (3 kg)
Dimensions
(H x W x D)
1.72 x 17.5 x 9.52 in.
(4.36 x 44.45 x 24.18 cm)
1. AWG = American Wire Gauge
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
A-3
Appendix A
Table A-4
Technical Specifications
Fiber-Port Specifications for Catalyst 2950C-24 and
Catalyst 2950SX-24 Switches
Fiber-Port Power Levels
Catalyst 2950C-24
nm1
Optical transmitter
wavelength
1300
Optical receiver
sensitivity
–34.5 to 31.8 dBm2
Catalyst 2950SX-24
850 nm
–13.5 dBm
Optical transmitter power –23.5 to –14 dBm
for 50/125-micron
cabling
–9.5 to –4 dBm
Optical transmitter power –20 to –14 dBm
for 62.5/125-micron
cabling
–9.5 to –4 dBm
1. nm = nanometers
2. dBm = decibel milliwatt
Table A-5
Catalyst 2950 Switch Agency Approvals
Safety
EMC
UL 60950/CSA 22.2 No.
950
FCC Part 15 Class A
IEC 60950/EN 60950
EN 55022: 1998 (CISPR22) Class A
AS/NZS 3260, TS001
EN 55024: 1998 (CISPR24)
CE
VCCI Class A
AS/NZS 3548 Class A
CE
CNS 13438 Class A
MIC
CLEI code
Catalyst 2950 Desktop Switch Hardware Installation Guide
A-4
78-11157-03
Appendix A
Technical Specifications
Table A-6
Catalyst 2950G-24-EI-DC Switch Agency Approvals
NEBS
Bellcore GR-1089-CORE
Bellcore GR-63-CORE
Bellcore SR-3580 Level 3
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
A-5
Appendix A
Technical Specifications
Catalyst 2950 Desktop Switch Hardware Installation Guide
A-6
78-11157-03
A P P E N D I X
B
Connectors and Cables
This appendix describes the connectors, cables, and adapters that you use to
connect the switch to other devices.
Connector Specifications
These sections describe the connectors used with the Catalyst 2950 switches and
contains this information:
•
10/100 Ports, page B-1
•
10/100/1000 Ports, page B-3
•
100BASE-FX and 1000BASE-SX Ports, page B-4
•
GigaStack GBIC Module Ports, page B-6
•
Console Port, page B-6
10/100 Ports
The 10/100 Ethernet ports use standard RJ-45 connectors and Ethernet pinouts
with internal crossovers, as shown by an X in the port name. These ports have the
transmit (TD) and receive (RD) signals internally crossed so that a twisted-pair
straight-through cable and adapter can be attached to the port. Figure B-1 shows
the pinout.
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
B-1
Appendix B
Connectors and Cables
Connector Specifications
When connecting 10/100 ports to other devices, such as servers, workstations, and
routers, you can use a two or four twisted-pair, straight-through cable wired for
10BASE-T and 100BASE-TX. Figure B-6 shows the two twisted-pair,
straight-through cable schematics. Figure B-8 shows the four twisted-pair,
straight-through cable schematics.
When connecting the ports to other devices, such as switches or repeaters, you can
use a two or four twisted-pair, crossover cable. Figure B-7 shows the two
twisted-pair, crossover cable schematics. Figure B-9 shows the four twisted-pair,
crossover cable schematics.
You can use Category 3, 4, or 5 cabling when connecting to 10BASE-T devices.
You must use Category 5 cabling when connecting to 100BASE-TX devices.
Use a straight-through cable to connect two ports only when one port is
designated with an X. Use a crossover cable to connect two ports when both ports
are designated with an X or when both ports do not have an X.
Figure B-1
10/100 RJ-45 Pinouts
Pin
Label
1
RD+
2
RD-
3
TD+
4
NC
5
NC
6
TD-
7
NC
8
NC
1 2 3 4 5 6 7 8
H5318
Note
Catalyst 2950 Desktop Switch Hardware Installation Guide
B-2
78-11157-03
Appendix B
Connectors and Cables
Connector Specifications
10/100/1000 Ports
The 10/100/1000 Ethernet ports on Catalyst 2950T-24 switches use standard
RJ-45 connectors. Figure B-2 shows the pinout.
Connecting to 10BASE-T and 100BASE-TX Devices
When connecting the ports to 10BASE-T and 100BASE-TX devices, such as
servers, workstations, and routers, you can use a two or four twisted-pair,
straight-through cable wired for 10BASE-T and100BASE-TX. Figure B-6 shows
the two twisted-pair, straight-through cable schematics. Figure B-8 shows the
four twisted-pair, straight-through cable schematics.
When connecting the ports to 10BASE-T- and 100BASE-TX devices, such as
switches or repeaters, you can use a two or four twisted-pair, crossover cable.
Figure B-7 shows the two twisted-pair, crossover cable schematics. Figure B-9
shows the four twisted-pair, crossover cable schematics.
You can use Category 3, 4, or 5 cabling when connecting to 10BASE-T devices.
You must use Category 5 cabling when connecting to 100BASE-TX devices.
Connecting to 1000BASE-T Devices
When connecting the ports to 1000BASE-T devices, such as servers,
workstations, and routers, you must use a four twisted-pair, Category 5,
straight-through cable wired for 10BASE-T, 100BASE-TX, and 1000BASE-T.
Figure B-10 shows the straight-through cable schematics.
When connecting the ports to other devices, such as switches or repeaters, you
must use a four twisted-pair, Category 5, crossover cable. Figure B-11 shows the
crossover cable schematics.
Note
Be sure to use a four twisted-pair, Category 5 cable when connecting to a
1000BASE-T device.
Note
Use a straight-through cable to connect two ports only when one port is
designated with an X. Use a crossover cable to connect two ports when both ports
are designated with an X or when both ports do not have an X.
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
B-3
Appendix B
Connectors and Cables
Connector Specifications
RJ-45 Pinouts for 10/100/1000 and 1000BASE-T GBIC Module Ports
Pin
Label
1
TP0+
2
TP0-
3
TP1+
4
TP2+
5
TP2-
6
TP1-
7
TP3+
8
TP3-
1234567 8
34751
Figure B-2
100BASE-FX and 1000BASE-SX Ports
The 100BASE-FX and 1000BASE-SX ports use MT-RJ connectors, shown in
Figure B-3. These ports use 50/125- or 62.5/125-micron multimode fiber-optic
cabling.
You can connect a 100BASE-FX or 1000BASE-SX port to an SC or ST port on a
target device by using one of the MT-RJ fiber-optic patch cables listed in
Table B-1. Use the Cisco part numbers in Table B-1 to order the patch cables that
you need.
MT-RJ Connector
28845
Figure B-3
Catalyst 2950 Desktop Switch Hardware Installation Guide
B-4
78-11157-03
Appendix B
Connectors and Cables
Connector Specifications
Table B-1
MT-RJ Patch Cables for 100BASE-FX and 1000BASE-SX
Connections
Type
Cisco Part Number
1-meter, MT-RJ-to-SC multimode cable
CAB-MTRJ-SC-MM-1M
3-meter, MT-RJ-to-SC multimode cable
CAB-MTRJ-SC-MM-3M
5-meter, MT-RJ-to-SC multimode cable
CAB-MTRJ-SC-MM-5M
1-meter, MT-RJ-to-ST multimode cable
CAB-MTRJ-ST-MM-1M
3-meter, MT-RJ-to-ST multimode cable
CAB-MTRJ-ST-MM-3M
5-meter, MT-RJ-to-ST multimode cable
CAB-MTRJ-ST-MM-5M
1000BASE-X GBIC Module Ports
1000BASE-X Gigabit Interface Converter (GBIC) module ports use duplex SC
connectors, as shown in Figure B-4.
1000BASE-X SC Connector
60535
Figure B-4
Tx
Rx
1000BASE-T GBIC Module Ports
The 1000BASE-T GBIC module port uses one RJ-45 connector, as shown in
Figure B-2.
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
B-5
Appendix B
Connectors and Cables
Connector Specifications
GigaStack GBIC Module Ports
The GigaStack GBIC module ports use proprietary connectors, as shown in
Figure B-5. The GigaStack GBIC cables are proprietary, high-data-rate cables
with enhanced signal integrity and EMI protection.
Caution
Do not use standard IEEE 1394 cables with the GigaStack GBIC.
GigaStack Connector
60536
Figure B-5
Console Port
The console port uses an 8-pin RJ-45 connector. You can connect a switch to a PC
through the console port and the supplied RJ-45-to-DB-9 adapter cable. If you
want to connect a switch to a terminal, you need to provide an RJ-45-to-DB-25
female DTE adapter. You can order a kit (part number ACS-DSBUASYN=) with
that adapter from Cisco. For console-port and adapter-pinout information, see
Table B-2 and Table B-3.
Catalyst 2950 Desktop Switch Hardware Installation Guide
B-6
78-11157-03
Appendix B
Connectors and Cables
Cable and Adapter Specifications
Cable and Adapter Specifications
These sections describe the cables and adapters used with Catalyst 2950 switches.
•
Two Twisted-Pair Cable Pinouts, page B-7
•
Four Twisted-Pair Cable Pinouts for 10/100 Ports, page B-8
•
Four Twisted-Pair Cable Pinouts for 1000BASE-T Ports, page B-9
Two Twisted-Pair Cable Pinouts
Figure B-6 and Figure B-7 show the schematics of two twisted-pair cables for
10/100 ports.
Two Twisted-Pair Straight-Through Cable Schematic for
10/100 Ports
Switch
Switch
3 TD+
6 TD–
3 RD+
6 RD–
1 RD+
2 RD–
1 TD+
2 TD–
Two Twisted-Pair Crossover Cable Schematic for 10/100 Ports
Switch
Switch
3 TD+
6 TD–
3 TD+
6 TD–
1 RD+
2 RD–
1 RD+
2 RD–
H5579
Figure B-7
H5578
Figure B-6
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
B-7
Appendix B
Connectors and Cables
Cable and Adapter Specifications
Four Twisted-Pair Cable Pinouts for 10/100 Ports
Figure B-8 and Figure B-9 show the schematics of four twisted-pair cables for
10/100 ports.
Switch
Switch
1 RD+
1 TD+
2 RD-
2 TD-
3 TD+
3 RD+
6 TD-
6 RD-
4 NC
4 NC
5 NC
5 NC
7 NC
7 NC
8 NC
8 NC
Figure B-9
65271
Four Twisted-Pair Straight-Through Cable Schematic for
10/100 Ports
Four Twisted-Pair Crossover Cable Schematic for 10/100 Ports
Switch
Switch
1 RD+
1 RD+
2 RD-
2 RD-
3 TD+
3 TD+
6 TD-
6 TD-
4 NC
4 NC
5 NC
5 NC
7 NC
7 NC
8 NC
8 NC
65273
Figure B-8
Catalyst 2950 Desktop Switch Hardware Installation Guide
B-8
78-11157-03
Appendix B
Connectors and Cables
Cable and Adapter Specifications
Four Twisted-Pair Cable Pinouts for 1000BASE-T Ports
Figure B-10 and Figure B-11 show the schematics of four twisted-pair cables for
10/100/1000 ports on Catalyst 2950T-24 switches and 1000BASE-T GBIC
module ports.
Switch
Switch
1 TPO+
1 TP1+
2 TPO-
2 TP1-
3 TP1+
3 TPO+
6 TP1-
6 TPO-
4 TP2+
4 TP3+
5 TP2-
5 TP3-
7 TP3+
7 TP2+
8 TP3-
8 TP2-
65272
Figure B-10 Four Twisted-Pair Straight-Through Cable Schematic for
10/100/1000 and 1000BASE-T GBIC Module Ports
Switch
Switch
1 TPO+
1 TP0+
2 TPO-
2 TP0-
3 TP1+
3 TP1+
6 TP1-
6 TP1-
4 TP2+
4 TP2+
5 TP2-
5 TP2-
7 TP3+
7 TP3+
8 TP3-
8 TP3-
65274
Figure B-11 Four Twisted-Pair Crossover Cable Schematics for 10/100/1000 and
1000BASE-T GBIC Module Ports
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
B-9
Appendix B
Connectors and Cables
Cable and Adapter Specifications
Cable and Adapter Pinouts
This section describes the cable and adapter pinouts and also describes how to
identify a rollover cable.
Connecting to a PC
Use the supplied RJ-45-to-DB-9 adapter cable to connect the console port to a PC
running terminal-emulation software. Figure B-12 shows how to connect the
console port to a PC. Table B-2 lists the pinouts for the console port and the
RJ-45-to-DB-9 adapter cable.
Figure B-12 Connecting the Console Port to a PC
RJ-45-to-DB-9
adapter cable
PC
74587
Catalyst 2950 switch
Table B-2
Console Port Signaling and RJ-45-to-DB-9 Adapter Cabling
Console
Port (DTE)
RJ-45-to-DB-9
Adapter Cable
Console
Device
Signal
RJ-45 Pin
DB-9 Pin
Signal
RTS
1
8
CTS
Not connected 2
6
DSR
TxD
3
2
RxD
GND
4
5
GND
GND
5
5
GND
RxD
6
3
TxD
Not connected 7
4
DTR
CTS
7
RTS
8
Catalyst 2950 Desktop Switch Hardware Installation Guide
B-10
78-11157-03
Appendix B
Connectors and Cables
Cable and Adapter Specifications
Connecting to a Terminal
Use the supplied RJ-45-to-DB-9 adapter cable and an RJ-45-to-DB-25 female
DTE adapter to connect the console port to a terminal. Figure B-13 shows how to
connect the console port to a terminal. Table B-3 lists the pinouts for the console
port, the adapter cable, and the RJ-45-to-DB-25 adapter.
Note
The RJ-45-to-DB-25 female DTE adapter is not supplied with the switch. You can
order a kit (part number ACS-DSBUASYN=) with that adapter from Cisco.
Figure B-13 Connecting the Console Port to a Terminal
RJ-45-to-DB-9
adapter cable
Terminal
74588
Catalyst 2950 series switch
Table B-3
Console Port Signaling and Cabling Using a DB-25 Adapter
Console
Port (DTE)
RJ-45-to-DB-9
Adapter Cable
RJ-45-to-DB-25
Terminal Adapter
Console
Device
Signal
RJ-45 Pin
DB-9 Pin
DB-25 Pin
Signal
RTS
1
8
5
CTS
Not
connected
2
6
6
DSR
TxD
3
2
3
RxD
GND
4
5
7
GND
GND
5
5
7
GND
RxD
6
3
2
TxD
Not
connected
7
4
20
DTR
CTS
8
7
4
RTS
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
B-11
Appendix B
Connectors and Cables
Cable and Adapter Specifications
Identifying a Rollover Cable
You can identify a rollover cable by comparing the two modular cable ends. Hold
the cable ends side-by-side, with the tab at the back. The wire connected to the
pin on the outside of the left plug should be the same color as the wire connected
to the pin on the outside of the right plug. (See Figure B-14.)
Figure B-14 Identifying a Rollover Cable
Pin 1 on one connector and
pin 8 on the other connector
should be the same color.
Pin 8
H10632
Pin 1
Catalyst 2950 Desktop Switch Hardware Installation Guide
B-12
78-11157-03
A P P E N D I X
C
Translated Safety Warnings
This appendix repeats in multiple languages the warnings in this guide. These
translated warnings can be used with other documents related to this guide.
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
C-1
Appendix C
Translated Safety Warnings
Attaching the Cisco RPS (model PWR300-AC-RPS-N1)
Attaching the Cisco RPS (model
PWR300-AC-RPS-N1)
Warning
Waarschuwing:
Varoitus
Avertissement :
Warnung:
Avvertenza.
Advarsel!
Attach only the Cisco RPS (model PWR300-AC-RPS-N1) to the RPS receptacle.
Slechts de Cisco RPS (model PWR300-AC-RPS-N1) aan de RPS
contactdoos verbinden.
Kiinnitä RPS-vastakappaleeseen vain Cisco RPS (malli
PWR300-AC-RPS-N1).
Raccordez le bloc d’alimentation Cisco RPS (modèle
PWR300-AC-RPS-N1) uniquement au connecteur RPS.
An die RPS-Steckhülse darf nur das Cisco RPS (Modell
PWR300-AC-RPSN1) angeschlossen werden.
Collegare soltanto il Cisco RPS (modello PWR300-AC-RPS-N1)
alla presa RPS.
Koble bare Cisco RPS (modell PWR300-AC-RPS-N1) til
RPS-stikkontakten.
Aviso
Anexe o RPS Cisco (modelo PWR300-AC-RPS-N1) apenas ao
receptáculo RPS.
Aviso:
Sólo conecte el Cisco RPS (modelo PWR300-AC-RPS-N1) al
receptáculo RPS.
Varning!
Koppla endast Ciscos RPS (modell PWR300-AC-RPS-N1) till RPS-uttaget.
Catalyst 2950 Desktop Switch Hardware Installation Guide
C-2
78-11157-03
Appendix C
Translated Safety Warnings
Lightning Activity Warning
Lightning Activity Warning
Warning
Waarschuwing
Varoitus
Do not work on the system or connect or disconnect cables during periods of
lightning activity.
Tijdens onweer dat gepaard gaat met bliksem, dient u niet aan
het systeem te werken of kabels aan te sluiten of te ontkoppelen.
Älä työskentele järjestelmän parissa äläkä yhdistä tai irrota
kaapeleita ukkosilmalla.
Attention
Ne pas travailler sur le système ni brancher ou débrancher les
câbles pendant un orage.
Warnung
Arbeiten Sie nicht am System und schließen Sie keine Kabel an
bzw. trennen Sie keine ab, wenn es gewittert.
Avvertenza
Advarsel
Aviso
¡Advertencia!
Varning!
Non lavorare sul sistema o collegare oppure scollegare i cavi
durante un temporale con fulmini.
Utfør aldri arbeid på systemet, eller koble kabler til eller fra
systemet når det tordner eller lyner.
Não trabalhe no sistema ou ligue e desligue cabos durante
períodos de mau tempo (trovoada).
No operar el sistema ni conectar o desconectar cables durante
el transcurso de descargas eléctricas en la atmósfera.
Vid åska skall du aldrig utföra arbete på systemet eller ansluta eller
koppla loss kablar.
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
C-3
Appendix C
Translated Safety Warnings
Installation Warning
Installation Warning
Warning
Waarschuwing
Varoitus
Read the installation instructions before you connect the system to its power
source.
Raadpleeg de installatie-aanwijzingen voordat u het systeem
met de voeding verbindt.
Lue asennusohjeet ennen järjestelmän yhdistämistä
virtalähteeseen.
Attention
Avant de brancher le système sur la source d'alimentation,
consulter les directives d'installation.
Warnung
Lesen Sie die Installationsanweisungen, bevor Sie das System
an die Stromquelle anschließen.
Avvertenza
Advarsel
Aviso
¡Advertencia!
Varning!
Consultare le istruzioni di installazione prima di collegare il
sistema all’alimentatore.
Les installasjonsinstruksjonene før systemet kobles til
strømkilden.
Leia as instruções de instalação antes de ligar o sistema à sua
fonte de energia.
Ver las instrucciones de instalación antes de conectar el
sistema a la red de alimentación.
Läs installationsanvisningarna innan du kopplar systemet till dess
strömförsörjningsenhet.
Catalyst 2950 Desktop Switch Hardware Installation Guide
C-4
78-11157-03
Appendix C
Translated Safety Warnings
Main Disconnecting Device
Main Disconnecting Device
Warning
Waarschuwing
Varoitus
The plug-socket combination must be accessible at all times because it
serves as the main disconnecting device.
De combinatie van de stekker en het elektrisch contactpunt moet te allen
tijde toegankelijk zijn omdat deze het hoofdmechanisme vormt voor
verbreking van de aansluiting.
Pistoke/liitinkohta toimii pääkatkaisumekanismina. Pääsy siihen on
pidettävä aina esteettömänä.
Attention
La combinaison de prise de courant doit être accessible à tout moment
parce qu'elle fait office de système principal de déconnexion.
Warnung
Der Netzkabelanschluß am Gerät muß jederzeit zugänglich sein, weil er
als primäre Ausschaltvorrichtung dient.
Avvertenza
Advarsel
Aviso
Il gruppo spina-presa deve essere sempre accessibile, poiché viene
utilizzato come dispositivo di scollegamento principale.
Kombinasjonen støpsel/uttak må alltid være tilgjengelig ettersom den
fungerer som hovedfrakoplingsenhet.
A combinação ficha-tomada deverá ser sempre acessível, porque
funciona como interruptor principal.
¡Advertencia!
El conjunto de clavija y toma ha de encontrarse siempre accesible ya que
hace las veces de dispositivo de desconexión principal.
Varning!
Man måste alltid kunna komma åt stickproppen i uttaget, eftersom denna
koppling utgör den huvudsakliga frånkopplingsanordningen.
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
C-5
Appendix C
Translated Safety Warnings
Chassis Warning—Rack-Mounting and Servicing
Chassis Warning—Rack-Mounting and Servicing
Warning
Waarschuwing
To prevent bodily injury when mounting or servicing this unit in a rack, you
must take special precautions to ensure that the system remains stable. The
following guidelines are provided to ensure your safety:
•
This unit should be mounted at the bottom of the rack if it is the only unit
in the rack.
•
When mounting this unit in a partially filled rack, load the rack from the
bottom to the top with the heaviest component at the bottom of the rack.
•
If the rack is provided with stabilizing devices, install the stabilizers before
mounting or servicing the unit in the rack.
Om lichamelijk letsel te voorkomen wanneer u dit toestel in een
rek monteert of het daar een servicebeurt geeft, moet u speciale
voorzorgsmaatregelen nemen om ervoor te zorgen dat het toestel
stabiel blijft. De onderstaande richtlijnen worden verstrekt om
uw veiligheid te verzekeren:
•
Dit toestel dient onderaan in het rek gemonteerd te worden als het toestel
het enige in het rek is.
•
Wanneer u dit toestel in een gedeeltelijk gevuld rek monteert, dient u het rek
van onderen naar boven te laden met het zwaarste onderdeel onderaan in het
rek.
•
Als het rek voorzien is van stabiliseringshulpmiddelen, dient u de
stabilisatoren te monteren voordat u het toestel in het rek monteert of het
daar een servicebeurt geeft.
Catalyst 2950 Desktop Switch Hardware Installation Guide
C-6
78-11157-03
Appendix C
Translated Safety Warnings
Chassis Warning—Rack-Mounting and Servicing
Varoitus
Attention
Kun laite asetetaan telineeseen tai huolletaan sen ollessa
telineessä, on noudatettava erityisiä varotoimia järjestelmän
vakavuuden säilyttämiseksi, jotta vältytään loukkaantumiselta.
Noudata seuraavia turvallisuusohjeita:
•
Jos telineessä ei ole muita laitteita, aseta laite telineen alaosaan.
•
Jos laite asetetaan osaksi täytettyyn telineeseen, aloita kuormittaminen sen
alaosasta kaikkein raskaimmalla esineellä ja siirry sitten sen yläosaan.
•
Jos telinettä varten on vakaimet, asenna ne ennen laitteen asettamista
telineeseen tai sen huoltamista siinä.
Pour éviter toute blessure corporelle pendant les opérations de
montage ou de réparation de cette unité en casier, il convient de
prendre des précautions spéciales afin de maintenir la stabilité
du système. Les directives ci-dessous sont destinées à assurer la
protection du personnel:
•
Si cette unité constitue la seule unité montée en casier, elle doit être placée
dans le bas.
•
Si cette unité est montée dans un casier partiellement rempli, charger le
casier de bas en haut en plaçant l'élément le plus lourd dans le bas.
•
Si le casier est équipé de dispositifs stabilisateurs, installer les stabilisateurs
avant de monter ou de réparer l'unité en casier.
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
C-7
Appendix C
Translated Safety Warnings
Chassis Warning—Rack-Mounting and Servicing
Warnung
Avvertenza
Zur Vermeidung von Körperverletzung beim Anbringen oder
Warten dieser Einheit in einem Gestell müssen Sie besondere
Vorkehrungen treffen, um sicherzustellen, daß das System stabil
bleibt. Die folgenden Richtlinien sollen zur Gewährleistung Ihrer
Sicherheit dienen:
•
Wenn diese Einheit die einzige im Gestell ist, sollte sie unten im Gestell
angebracht werden.
•
Bei Anbringung dieser Einheit in einem zum Teil gefüllten Gestell ist das
Gestell von unten nach oben zu laden, wobei das schwerste Bauteil unten
im Gestell anzubringen ist.
•
Wird das Gestell mit Stabilisierungszubehör geliefert, sind zuerst die
Stabilisatoren zu installieren, bevor Sie die Einheit im Gestell anbringen
oder sie warten.
Per evitare infortuni fisici durante il montaggio o la
manutenzione di questa unità in un supporto, occorre osservare
speciali precauzioni per garantire che il sistema rimanga
stabile. Le seguenti direttive vengono fornite per garantire la
sicurezza personale:
•
Questa unità deve venire montata sul fondo del supporto, se si tratta
dell’unica unità da montare nel supporto.
•
Quando questa unità viene montata in un supporto parzialmente pieno,
caricare il supporto dal basso all’alto, con il componente più pesante
sistemato sul fondo del supporto.
•
Se il supporto è dotato di dispositivi stabilizzanti, installare tali dispositivi
prima di montare o di procedere alla manutenzione dell’unità nel supporto.
Catalyst 2950 Desktop Switch Hardware Installation Guide
C-8
78-11157-03
Appendix C
Translated Safety Warnings
Chassis Warning—Rack-Mounting and Servicing
Advarsel
Aviso
Unngå fysiske skader under montering eller reparasjonsarbeid
på denne enheten når den befinner seg i et kabinett. Vær nøye
med at systemet er stabilt. Følgende retningslinjer er gitt for å
verne om sikkerheten:
•
Denne enheten bør monteres nederst i kabinettet hvis dette er den eneste
enheten i kabinettet.
•
Ved montering av denne enheten i et kabinett som er delvis fylt, skal
kabinettet lastes fra bunnen og opp med den tyngste komponenten nederst i
kabinettet.
•
Hvis kabinettet er utstyrt med stabiliseringsutstyr, skal stabilisatorene
installeres før montering eller utføring av reparasjonsarbeid på enheten i
kabinettet.
Para se prevenir contra danos corporais ao montar ou reparar
esta unidade numa estante, deverá tomar precauções especiais
para se certificar de que o sistema possui um suporte estável. As
seguintes directrizes ajudá-lo-ão a efectuar o seu trabalho com
segurança:
•
Esta unidade deverá ser montada na parte inferior da estante, caso seja esta
a única unidade a ser montada.
•
Ao montar esta unidade numa estante parcialmente ocupada, coloque os
itens mais pesados na parte inferior da estante, arrumando-os de baixo para
cima.
•
Se a estante possuir um dispositivo de estabilização, instale-o antes de
montar ou reparar a unidade.
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
C-9
Appendix C
Translated Safety Warnings
Chassis Warning—Rack-Mounting and Servicing
¡Advertencia!
Varning!
Para evitar lesiones durante el montaje de este equipo sobre un
bastidor, o posteriormente durante su mantenimiento, se debe
poner mucho cuidado en que el sistema quede bien estable. Para
garantizar su seguridad, proceda según las siguientes
instrucciones:
•
Colocar el equipo en la parte inferior del bastidor, cuando sea la única
unidad en el mismo.
•
Cuando este equipo se vaya a instalar en un bastidor parcialmente ocupado,
comenzar la instalación desde la parte inferior hacia la superior colocando
el equipo más pesado en la parte inferior.
•
Si el bastidor dispone de dispositivos estabilizadores, instalar éstos antes de
montar o proceder al mantenimiento del equipo instalado en el bastidor.
För att undvika kroppsskada när du installerar eller utför underhållsarbete
på denna enhet på en ställning måste du vidta särskilda
försiktighetsåtgärder för att försäkra dig om att systemet står stadigt.
Följande riktlinjer ges för att trygga din säkerhet:
•
Om denna enhet är den enda enheten på ställningen skall den installeras
längst ned på ställningen.
•
Om denna enhet installeras på en delvis fylld ställning skall ställningen
fyllas nedifrån och upp, med de tyngsta enheterna längst ned på ställningen.
•
Om ställningen är försedd med stabiliseringsdon skall dessa monteras fast
innan enheten installeras eller underhålls på ställningen.
Catalyst 2950 Desktop Switch Hardware Installation Guide
C-10
78-11157-03
Appendix C
Translated Safety Warnings
Overtemperature Warning
Overtemperature Warning
Warning
To prevent the switch from overheating, do not operate it in an area that
exceeds the maximum recommended ambient temperature of 104°F (40°C). To
prevent airflow restriction, allow at least 3 inches (7.6 cm) of clearance
around the ventilation openings.
Waarschuwing
Om oververhitting van de schakelaar te voorkomen, mag u die
niet bedienen in een ruimte die de maximale aanbevolen
omgevingstemperatuur van 104°F (40°C) overschrijdt. Om
beperking van de luchtstroom te voorkomen, dient u ten minste 3
inch (7,6 cm) speling te laten rondom de ventilatie-openingen.
Varoitus
Estääksesi kytkimen ylikuumenemisen älä käytä sitä sellaisissa
paikoissa, joiden lämpötila ylittää ympäristön
enimmäislämpötilaksi suositellun 40°C. Jätä vähintään 7,6 cm:n
vapaa tila tuuletusaukkojen ympärille, jotta ilma pääsee
vapaasti virtaamaan.
Attention
Pour éviter une surchauffe du commutateur, ne pas le faire
fonctionner dans un local dont la température ambiante dépasse
le maximum recommandé de 40°C (104°F). Pour faciliter la
circulation d'air, aménager un dégagement d'au moins 7,6 cm
(3 pouces) autour des bouches d'aération.
Warnung
Um eine Überhitzung des Schalters zu vermeiden, ist das System
nicht in einem Bereich zu betreiben, in dem die empfohlene
Höchsttemperatur von 40°C überschritten wird. Damit der
Luftfluß nicht behindert wird, ist ein Freiraum von mindestens 7,6
cm um die Belüftungsöffnungen herum einzuhalten.
Avvertenza
Per evitare il surriscaldamento dell’interruttore, non usare
l'apparecchiatura in un’area che supera la temperatura
ambientale minima consigliata di 40°C. Per evitare una
limitazione del flusso dell’aria, lasciare come minimo uno spazio
libero di 7,6 cm intorno alle aperture di ventilazione.
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
C-11
Appendix C
Translated Safety Warnings
No On/Off Switch Warning
Advarsel
For å unngå at bryteren overopphetes skal utstyret ikke brukes på
steder hvor anbefalt maks omgivelsestemperatur overstiger 104
grader Farenheit (40°C). La det være minst 3 tommer (7,6 cm)
klaring rundt ventilasjonsåpningene for at luftsirkulasjonen skal
være uhindret.
Aviso
Para evitar sobreaquecimento do interruptor, não utilize o
equipamento numa àrea que exceda uma temperatura máxima de
40°C. Para evitar o bloqueamento da circulação de ar, deixe pelo
menos um espaço de 7.6 cm em volta das aberturas de
ventilação.
¡Advertencia!
Varning!
Para evitar que el interruptor se recaliente, no se debe usar en
áreas cuya temperatura ambiente exceda la máxima
recomendada, esto es, 40°C (104°F). Para no entorpecer la
corriente de aire, dejar por lo menos 7,6 cm (3 pulgadas) de
espacio muerto alrededor de la rejilla de ventilación.
För att undvika överhettning av strömbrytaren skall den inte användas i
utrymme vars temperatur överskrider den maximalt rekommenderade
omgivningstemperaturen 40°C. Kontrollera att det finns minst 7,6 cm fritt
utrymme runt ventilationsöppningarna så att luftflödet inte begränsas.
No On/Off Switch Warning
Warning
Waarschuwing
Varoitus
Unplug the power cord before you work on a system that does not have an
on/off switch.
Voordat u aan een systeem werkt dat geen aan/uit schakelaar
heeft, dient u de stekker van het netsnoer uit het stopcontact te
halen.
Ennen kuin teet mitään sellaiselle järjestelmälle, jossa ei ole
kaksiasentokytkintä, kytke irti virtajohto.
Catalyst 2950 Desktop Switch Hardware Installation Guide
C-12
78-11157-03
Appendix C
Translated Safety Warnings
Grounded Equipment Warning
Attention
Avant de travailler sur un système non équipé d'un commutateur
marche-arrêt, débrancher le cordon d'alimentation.
Warnung
Bevor Sie an einem System ohne Ein/Aus-Schalter arbeiten,
ziehen Sie das Netzkabel heraus.
Avvertenza
Advarsel
Aviso
¡Advertencia!
Varning!
Prima di lavorare su un sistema che non è dotato di un
interruttore on/off, scollegare il cavo di alimentazione.
Før det skal utføres arbeid på et system som ikke har en
av/på-bryter, skal strømledningen trekkes ut.
Antes de começar a trabalhar num sistema que não possua um
interruptor ON/OFF, desligue o cabo de alimentação.
Antes de trabajar sobre cualquier sistema que carezca de
interruptor de Encendido/Apagado (ON/OFF), desenchufar el
cable de alimentación.
Dra ur nätsladden innan du utför arbete på ett system utan strömbrytare.
Grounded Equipment Warning
Warning
Waarschuwing
Varoitus
This equipment is intended to be grounded. Ensure that the host is connected
to earth ground during normal use.
Deze apparatuur hoort geaard te worden Zorg dat de
host-computer tijdens normaal gebruik met aarde is verbonden.
Tämä laitteisto on tarkoitettu maadoitettavaksi. Varmista, että
isäntälaite on yhdistetty maahan normaalikäytön aikana.
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
C-13
Appendix C
Translated Safety Warnings
Product Disposal Warning
Attention
Cet équipement doit être relié à la terre. S’assurer que l’appareil
hôte est relié à la terre lors de l’utilisation normale.
Warnung
Dieses Gerät muß geerdet werden. Stellen Sie sicher, daß das
Host-Gerät während des normalen Betriebs an Erde gelegt ist.
Avvertenza
Questa apparecchiatura deve essere collegata a massa.
Accertarsi che il dispositivo host sia collegato alla massa di
terra durante il normale utilizzo.
Advarsel
Dette utstyret skal jordes. Forviss deg om vertsterminalen er
jordet ved normalt bruk.
Aviso
¡Advertencia!
Varning!
Este equipamento deverá estar ligado à terra. Certifique-se que
o host se encontra ligado à terra durante a sua utilização normal.
Este equipo debe conectarse a tierra. Asegurarse de que el
equipo principal esté conectado a tierra durante el uso normal.
Denna utrustning är avsedd att jordas. Se till att värdenheten är jordad vid
normal användning.
Product Disposal Warning
Warning
Waarschuwing
Varoitus
Ultimate disposal of this product should be handled according to all national
laws and regulations.
Dit produkt dient volgens alle landelijke wetten en voorschriften
te worden afgedankt.
Tämän tuotteen lopullisesta hävittämisestä tulee huolehtia
kaikkia valtakunnallisia lakeja ja säännöksiä noudattaen.
Catalyst 2950 Desktop Switch Hardware Installation Guide
C-14
78-11157-03
Appendix C
Translated Safety Warnings
Ground Connection Warning
Attention
La mise au rebut définitive de ce produit doit être effectuée
conformément à toutes les lois et réglementations en vigueur.
Warnung
Dieses Produkt muß den geltenden Gesetzen und Vorschriften
entsprechend entsorgt werden.
Avvertenza
L'eliminazione finale di questo prodotto deve essere eseguita
osservando le normative italiane vigenti in materia.
Advarsel
Endelig disponering av dette produktet må skje i henhold til
nasjonale lover og forskrifter.
Aviso
A descartagem final deste produto deverá ser efectuada de
acordo com os regulamentos e a legislação nacional.
¡Advertencia!
Varning!
El desecho final de este producto debe realizarse según todas
las leyes y regulaciones nacionales.
Vid deponering hanteras produkten enligt gällande lagar och
bestämmelser.
Ground Connection Warning
Warning
Waarschuwing
Varoitus
When installing the unit, always make the ground connection first and
disconnect it last.
Bij de installatie van het toestel moet de aardverbinding altijd
het eerste worden gemaakt en het laatste worden losgemaakt.
Laitetta asennettaessa on maahan yhdistäminen aina tehtävä
ensiksi ja maadoituksen irti kytkeminen viimeiseksi.
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
C-15
Appendix C
Translated Safety Warnings
Ground Connection Warning
Attention
Lors de l’installation de l’appareil, la mise à la terre doit toujours
être connectée en premier et déconnectée en dernier.
Warnung
Der Erdanschluß muß bei der Installation der Einheit immer
zuerst hergestellt und zuletzt abgetrennt werden.
Avvertenza
In fase di installazione dell'unità, eseguire sempre per primo il
collegamento a massa e disconnetterlo per ultimo.
Advarsel
Når enheten installeres, må jordledningen alltid tilkobles først
og frakobles sist.
Aviso
¡Advertencia!
Varning!
Ao instalar a unidade, a ligação à terra deverá ser sempre a
primeira a ser ligada, e a última a ser desligada.
Al instalar el equipo, conectar la tierra la primera y
desconectarla la última.
Vid installation av enheten måste jordledningen alltid anslutas först och
kopplas bort sist.
Catalyst 2950 Desktop Switch Hardware Installation Guide
C-16
78-11157-03
Appendix C
Translated Safety Warnings
Jewelry Removal Warning
Jewelry Removal Warning
Warning
Before working on equipment that is connected to power lines, remove
jewelry (including rings, necklaces, and watches). Metal objects will heat up
when connected to power and ground and can cause serious burns or weld the
metal object to the terminals.
Waarschuwing
Alvorens aan apparatuur te werken die met elektrische
leidingen is verbonden, sieraden (inclusief ringen, kettingen en
horloges) verwijderen. Metalen voorwerpen worden warm
wanneer ze met stroom en aarde zijn verbonden, en kunnen
ernstige brandwonden veroorzaken of het metalen voorwerp aan
de aansluitklemmen lassen.
Varoitus
Ennen kuin työskentelet voimavirtajohtoihin kytkettyjen
laitteiden parissa, ota pois kaikki korut (sormukset, kaulakorut
ja kellot mukaan lukien). Metalliesineet kuumenevat, kun ne
ovat yhteydessä sähkövirran ja maan kanssa, ja ne voivat
aiheuttaa vakavia palovammoja tai hitsata metalliesineet kiinni
liitäntänapoihin.
Attention
Avant d’accéder à cet équipement connecté aux lignes
électriques, ôter tout bijou (anneaux, colliers et montres
compris). Lorsqu’ils sont branchés à l’alimentation et reliés à la
terre, les objets métalliques chauffent, ce qui peut provoquer des
blessures graves ou souder l’objet métallique aux bornes.
Warnung
Vor der Arbeit an Geräten, die an das Netz angeschlossen sind,
jeglichen Schmuck (einschließlich Ringe, Ketten und Uhren)
abnehmen. Metallgegenstände erhitzen sich, wenn sie an das
Netz und die Erde angeschlossen werden, und können schwere
Verbrennungen verursachen oder an die Anschlußklemmen
angeschweißt werden.
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
C-17
Appendix C
Translated Safety Warnings
Jewelry Removal Warning
Avvertenza
Prima di intervenire su apparecchiature collegate alle linee di
alimentazione, togliersi qualsiasi monile (inclusi anelli, collane,
braccialetti ed orologi). Gli oggetti metallici si riscaldano
quando sono collegati tra punti di alimentazione e massa:
possono causare ustioni gravi oppure il metallo può saldarsi ai
terminali.
Advarsel
Fjern alle smykker (inkludert ringer, halskjeder og klokker) før
du skal arbeide på utstyr som er koblet til kraftledninger.
Metallgjenstander som er koblet til kraftledninger og jord blir
svært varme og kan forårsake alvorlige brannskader eller smelte
fast til polene.
Aviso
Antes de trabalhar em equipamento que esteja ligado a linhas de
corrente, retire todas as jóias que estiver a usar (incluindo anéis,
fios e relógios). Os objectos metálicos aquecerão em contacto
com a corrente e em contacto com a ligação à terra, podendo
causar queimaduras graves ou ficarem soldados aos terminais.
¡Advertencia!
Antes de operar sobre equipos conectados a líneas de
alimentación, quitarse las joyas (incluidos anillos, collares y
relojes). Los objetos de metal se calientan cuando se conectan a
la alimentación y a tierra, lo que puede ocasionar quemaduras
graves o que los objetos metálicos queden soldados a los
bornes.
Varning!
Tag av alla smycken (inklusive ringar, halsband och armbandsur) innan du
arbetar på utrustning som är kopplad till kraftledningar. Metallobjekt
hettas upp när de kopplas ihop med ström och jord och kan förorsaka
allvarliga brännskador; metallobjekt kan också sammansvetsas med
kontakterna.
Catalyst 2950 Desktop Switch Hardware Installation Guide
C-18
78-11157-03
Appendix C
Translated Safety Warnings
Stacking the Chassis Warning
Stacking the Chassis Warning
Warning
Waarschuwing
Varoitus
Do not stack the chassis on any other equipment. If the chassis falls, it can
cause severe bodily injury and equipment damage.
Het chassis mag niet op andere apparatuur gestapeld te worden.
Als het chassis mocht vallen, kan dit ernstig lichamelijk letsel en
beschadiging van de apparatuur veroorzaken.
Älä aseta asennuspohjaa minkään muun laitteen päälle.
Asennuspohja voi pudotessaan aiheuttaa vaikean
ruumiinvamman tai laitevaurion.
Avertissement
Ne placez pas ce châssis sur un autre appareil. En cas de chute,
il pourrait provoquer de graves blessures corporelles et
d'importants dommages.
Achtung
Das Gehäuse nicht auf andere Geräte stellen. Wenn das Gehäuse
herunterfällt, besteht Gefahr schwerer Personenverletzungen
und Geräteschäden.
Avvertenza
Advarsel
Aviso
Non collocare lo chassis su nessun altro apparecchio. Se lo
chassis cade, può causare lesioni gravi e danni alle
apparecchiature.
Stable ikke kabinettet oppå annet utstyr. Hvis kabinettet faller,
kan det forårsake alvorlig skade på mennesker og utstyr.
Não coloque o chassis em cima de qualquer outro equipamento.
Se o chassis cair, poderá causar ferimentos graves e danos no
equipamento.
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
C-19
Appendix C
Translated Safety Warnings
Qualified Personnel Warning
¡Atención!
Varning
No apilar los chasis sobre ningún otro equipo. Si el chasis se cae
al suelo puede causar graves lesiones físicas y daños al equipo.
Placera inte chassit ovanpå annan utrustning. Om chassit faller kan
allvarlig kroppsskada såväl som skada på utrustningen uppstå.
Qualified Personnel Warning
Warning
Waarschuwing
Varoitus
Avertissement
Achtung
Only trained and qualified personnel should be allowed to install or replace
this equipment.
Installatie en reparaties mogen uitsluitend door getraind en
bevoegd personeel uitgevoerd worden.
Ainoastaan koulutettu ja pätevä henkilökunta saa asentaa tai
vaihtaa tämän laitteen.
Tout installation ou remplacement de l'appareil doit être réalisé
par du personnel qualifié et compétent.
Gerät nur von geschultem, qualifiziertem Personal installieren
oder auswechseln lassen.
Avvertenza
Solo personale addestrato e qualificato deve essere autorizzato
ad installare o sostituire questo apparecchio.
Advarsel
Kun kvalifisert personell med riktig opplæring bør montere eller
bytte ut dette utstyret.
Aviso
Este equipamento deverá ser instalado ou substituído apenas por
pessoal devidamente treinado e qualificado.
Catalyst 2950 Desktop Switch Hardware Installation Guide
C-20
78-11157-03
Appendix C
Translated Safety Warnings
Class 1 Laser Product Warning
¡Atención!
Varning
Estos equipos deben ser instalados y reemplazados
exclusivamente por personal técnico adecuadamente preparado
y capacitado.
Denna utrustning ska endast installeras och bytas ut av utbildad och
kvalificerad personal.
Class 1 Laser Product Warning
Warning
Waarschuwing:
Varoitus:
Avertissement :
Warnung:
Avvertenza.
Advarsel!
Class 1 Laser Product
Waarschuwing voor klasse 1 laserprodukten
lasertuote luokka 1
Produits Laser Class 1
Produkt-Warnhinweis zu Lasergeräten der Klasse 1
Prodotto Laser di Classe 1
Advarsel for laserprodukter i klasse 1
Aviso
Aviso sobre produtos a laser da Classe 1
Aviso
É Aviso sobre producto láser de Clase 1
Varning!
Varning beträffande laserprodukt, klass 1
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
C-21
Appendix C
Translated Safety Warnings
Laser Beam Exposure Warning
Laser Beam Exposure Warning
Warning
Waarschuwing
Varoitus
Avoid exposure to the laser beam.
Vermijd blootstelling aan de straal.
Vältä säteelle altistumista.
Attention
Eviter toute exposition au faisceau.
Warnung
Schützen Sie sich vor Strahlung.
Avvertenza
Advarsel
Aviso
¡Advertencia!
Varning!
Evitare l’esposizione al raggio.
Unngå å bli utsatt for strålen.
Evite exposição ao raio.
Evitar la exposición al haz.
Utsätt dig inte för laserstrålningen.
Catalyst 2950 Desktop Switch Hardware Installation Guide
C-22
78-11157-03
Appendix C
Translated Safety Warnings
Catalyst 2950G-24-EI-DC Service Requirement
Catalyst 2950G-24-EI-DC Service Requirement
Warning
The Catalyst 2950G-24-EI-DC contains no field-replaceable units
(FRUs). Do not open the chassis or attempt to remove or replace
any components. For information about obtaining service for this
unit, contact your reseller or Cisco sales representative.
Waarschuwing
De Catalyst 2950G-24-EI-DC bevat geen FRU's (field-replaceable
units ofwel veldvervangbare eenheden). Open het chassis niet en
probeer geen onderdelen te verwijderen of te vervangen. Voor
informatie omtrent het onderhoud voor deze eenheid dient u
contact op te nemen met uw doorverkoper of
verkoopvertegenwoordiger van Cisco.
Varoitus
Catalyst 2950G-24-EI-DC ei sisällä kenttäkorjattavia laitteita.
Runkoa ei saa avata, eikä osia saa yrittää poistaa tai korjata.
Laitteen huoltoa koskevia tietoja saa jälleenmyyjältä tai Ciscon
myyntiedustajalta.
Attention
Le Catalyst 2950G-24-EI-DC ne dispose pas d'unités remplaçables
sur site (FRU). Il est recommandé de ne pas ouvrir le châssis ni
de retirer ou remplacer des composants. Pour plus de détails sur
la maintenance de cette unité, contactez votre revendeur ou
votre ingénieur commercial Cisco.
Warnung
Der Catalyst 2950G-24-EI-DC enthält keine vor Ort
austauschbaren Einheiten (FRUs). Das Gehäuse nicht öffnen und
Komponenten nicht entfernen oder ersetzen.
Serviceinformationen zu dieser Einheit erhalten Sie von Ihrem
Wiederverkäufer oder von Ihrem Cisco-Vertreter.
Avvertenza
Catalyst 2950G-24-EI-DC non ha componenti sostituibili sul posto
(FRU). Non aprite lo chassis o tentate di rimuovere o sostituire
componenti. Per maggiori informazioni sui servizi di assistenza
per questo dispositivo, contattate il vostro rivenditore Cisco.
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
C-23
Appendix C
Translated Safety Warnings
Restricted Area Equipment Installation
Advarsel
Catalyst 2950G-24-EI-DC inneholder ingen kunde-utskiftbare
deler (FRU-deler). Gjør ikke forsøk på å åpne kabinettet eller
fjerne eller skifte ut noen av komponentene. Ta kontakt med
forhandleren eller en Cisco-salgsrepresentant for informasjon
om hvor det kan utføres service på enheten.
Aviso
O interruptor Catalisador 2950G-24-EI-DC não contém nenhuma
unidade substituível em campo. Não abrir o chassis ou tentar
remover ou substituir quaisquer componentes. Para mais
informações sobre a manutenção desta unidade, contactar o seu
revendedor ou um representante de vendas da Cisco.
¡Advertencia!
El Catalyst 2950G-24-EI-DC no contiene componentes
reemplazables en las instalaciones (Field-Replaceable Units,
FRU). No abra el chasis ni intente reemplazar componentes. Para
más información sobre cómo reparar este aparato, póngase en
contacto con su distribuidor o representante de Cisco.
Varning!
Catalyst 2950G-24-EI-DC innehåller inte några enheter som kan
bytas ut på fältet. Öppna inte chassit och försök inte heller att ta
bort eller byta ut några delar. Kontakta återförsäljaren eller
representanten för Cisco om du behöver information om service
av enheten.
Restricted Area Equipment Installation
Warning
Waarschuwing
Varoitus
The equipment is to be installed in a restricted access area.
De uitrusting dient geïnstalleerd te worden in een gebied met
beperkte toegang.
Laite tulee asentaa tilaan, johon on rajoitettu pääsy.
Catalyst 2950 Desktop Switch Hardware Installation Guide
C-24
78-11157-03
Appendix C
Translated Safety Warnings
Ethernet Cable Shielding in Offices
Attention
Cet équipement doit être installé uniquement dans une zone à
accès limité.
Warnung
Die Ausrüstung muß in einem Bereich installiert werden, der
gegen unbefugtes Betreten geschützt ist.
Avvertenza
Installate questo apparato unicamente in zone di accesso
regolamentate.
Advarsel
Utstyret skal installeres på et sted med begrenset adgang.
Aviso
¡Advertencia!
Varning!
O equipamento é para ser instalado numa área de acesso
restrito.
El equipo debe instalarse en una zona de acceso restringido.
Utrustningen måste installeras på plats med åtkomst endast för
behörig personal.
Ethernet Cable Shielding in Offices
Warning
Waarschuwing
Ethernet cables must be shielded when used in a central office
environment.
Ethernetkabels dienen beveiligd te worden als ze in een centrale
kantooromgeving worden gebruikt.
Varoitus
Ethernet-kaapelit täytyy suojata, kun niitä käytetään yleisessä
toimistoympäristössä.
Attention
Pour une utilisation en site central, les câbles Ethernet doivent
être impérativement blindés.
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
C-25
Appendix C
Translated Safety Warnings
DC Power Disconnection Warning
Warnung
Avvertenza
Advarsel
Aviso
¡Advertencia!
Varning!
Ethernet-Kabel müssen abgeschirmt werden, wenn sie in einer
Zentrale eingesetzt werden.
I cavi Ethernet devono essere schermati se utilizzati in un
ambiente di ufficio centrale.
Ethernet-kabler skal være skjermet når de brukes i et sentralt
kontormiljø.
Os cabos “Ethernet” deverão estar armados quando usados em
ambiente de escritório central.
Los cables Ethernet deben estar protegidos cuando se usen
dentro de una oficina central.
Ethernetkablar måste vara avskärmade vid användning i central
kontorsmiljö.
DC Power Disconnection Warning
Warning
Before performing any of the following procedures, ensure that
power is removed from the DC circuit. To ensure that all power is
OFF, locate the circuit breaker on the panel board that services
the DC circuit, switch the circuit breaker to the OFF position, and
tape the switch handle of the circuit breaker in the OFF position.
Waarschuwing
Voordat u een van de onderstaande procedures uitvoert, dient u
te controleren of de stroom naar het gelijkstroom circuit
uitgeschakeld is. Om u ervan te verzekeren dat alle stroom UIT is
geschakeld, kiest u op het schakelbord de stroomverbreker die
het gelijkstroom circuit bedient, draait de stroomverbreker naar
de UIT positie en plakt de schakelaarhendel van de
stroomverbreker met plakband in de UIT positie vast.
Catalyst 2950 Desktop Switch Hardware Installation Guide
C-26
78-11157-03
Appendix C
Translated Safety Warnings
DC Power Disconnection Warning
Varoitus
Varmista, että tasavirtapiirissä ei ole virtaa ennen seuraavien
toimenpiteiden suorittamista. Varmistaaksesi, että virta on
KATKAISTU täysin, paikanna tasavirrasta huolehtivassa
kojetaulussa sijaitseva suojakytkin, käännä suojakytkin
KATKAISTU-asentoon ja teippaa suojakytkimen varsi niin, että
se pysyy KATKAISTU-asennossa.
Attention
Avant de pratiquer l'une quelconque des procédures ci-dessous,
vérifier que le circuit en courant continu n'est plus sous tension.
Pour en être sûr, localiser le disjoncteur situé sur le panneau de
service du circuit en courant continu, placer le disjoncteur en
position fermée (OFF) et, à l'aide d'un ruban adhésif, bloquer la
poignée du disjoncteur en position OFF.
Warnung
Vor Ausführung der folgenden Vorgänge ist sicherzustellen, daß
die Gleichstromschaltung keinen Strom erhält. Um
sicherzustellen, daß sämtlicher Strom abgestellt ist, machen Sie
auf der Schalttafel den Unterbrecher für die
Gleichstromschaltung ausfindig, stellen Sie den Unterbrecher
auf AUS, und kleben Sie den Schaltergriff des Unterbrechers mit
Klebeband in der AUS-Stellung fest.
Avvertenza
Prima di svolgere una qualsiasi delle procedure seguenti,
verificare che il circuito CC non sia alimentato. Per verificare
che tutta l’alimentazione sia scollegata (OFF), individuare
l’interruttore automatico sul quadro strumenti che alimenta il
circuito CC, mettere l’interruttore in posizione OFF e fissarlo con
nastro adesivo in tale posizione.
Advarsel
Før noen av disse prosedyrene utføres, kontroller at strømmen er
frakoblet likestrømkretsen. Sørg for at all strøm er slått AV. Dette
gjøres ved å lokalisere strømbryteren på brytertavlen som
betjener likestrømkretsen, slå strømbryteren AV og teipe
bryterhåndtaket på strømbryteren i AV-stilling.
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
C-27
Appendix C
Translated Safety Warnings
DC Power Disconnection Warning
Aviso
Antes de executar um dos seguintes procedimentos,
certifique-se que desligou a fonte de alimentação de energia do
circuito de corrente contínua. Para se assegurar que toda a
corrente foi DESLIGADA, localize o disjuntor no painel que serve
o circuito de corrente contínua e coloque-o na posição OFF
(Desligado), segurando nessa posição a manivela do interruptor
do disjuntor com fita isoladora.
¡Advertencia!
Antes de proceder con los siguientes pasos, comprobar que la
alimentación del circuito de corriente continua (CC) esté cortada
(OFF). Para asegurarse de que toda la alimentación esté cortada
(OFF), localizar el interruptor automático en el panel que
alimenta al circuito de corriente continua, cambiar el interruptor
automático a la posición de Apagado (OFF), y sujetar con cinta la
palanca del interruptor automático en posición de Apagado
(OFF).
Varning!
Innan du utför någon av följande procedurer måste du kontrollera
att strömförsörjningen till likströmskretsen är bruten.
Kontrollera att all strömförsörjning är BRUTEN genom att slå AV
det överspänningsskydd som skyddar likströmskretsen och tejpa
fast överspänningsskyddets omkopplare i FRÅN-läget.
Catalyst 2950 Desktop Switch Hardware Installation Guide
C-28
78-11157-03
Appendix C
Translated Safety Warnings
Exposed DC Power Wire Warning
Exposed DC Power Wire Warning
Warning
Waarschuwing
An exposed wire lead from a DC-input power source can conduct
harmful levels of electricity. Be sure that no exposed portion of
the DC-input power source wire extends from the terminal block
plug.
Een blootgestelde verbindingsdraad van een
ingangsgelijkstroombron kan gevaarlijke elektriciteitsniveaus
geleiden. Zorg ervoor dat geen blootgesteld deel van het draad
van de ingangsgelijkstroombron zich uitstrekt vanuit het
aansluitblok van de terminal.
Varoitus
Tasavirtalähteestä tuleva avoin johto voi johtaa vaarallisen
määrän sähköä. Varmista, ettei kaapelikengän pistokkeesta tule
esille lainkaan tasavirtajohdon avointa osaa.
Attention
Pour éviter tout risque de choc électrique, vérifiez que les câbles
d'alimentation secteur sont protégés par une gaine. Aucun fil
dénudé ne doit apparaître hors du bloc d'alimentation du
terminal.
Warnung
Eine ungeschützte Kabelleitung von einer
Gleichstrom-Eingangsspannungsquelle kann schädliche
Elektrizitätslevel führen. Achten Sie darauf, daß von dem
Klemmleistenstecker aus kein ungeschütztes
Eingangsgleichstromkabel freiliegt.
Avvertenza
Advarsel
Un cavo elettrico scoperto proveniente da un alimentatore
DC-INPUT può trasmettere scariche elettriche ad elevata
tensione. Assicuratevi che i cavi in uscita dall'alimentatore
DC-input non presentino punti scoperti.
En avdekket ledning fra en likestrømskilde kan lede farlig
elektrisitet. Kontroller at ingen avdekkede deler av ledningen til
likestrømskilden stikker ut av terminalens koblingsblokk.
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
C-29
Appendix C
Translated Safety Warnings
Service Personnel Warning
Aviso
Um fio condutor exposto de uma unidade de entrada de DC
(corrente contínua) pode transportar níveis perigosos de
electricidade. Certifique-se de que nenhuma secção exposta de
um fio condutor da fonte de energia de entrada de DC se extende
a partir da ficha da placa de terminais.
¡Advertencia!
Un cable desnudo de una fuente de entrada de alimentación de
corriente directa (DC) puede conducir niveles de electricidad
peligrosos. Asegúrese de que ninguna parte del cable de la
fuente de alimentación de DC de entrada sale del enchufe del
bloque de terminal.
Varning!
En blottad trådledning från en likströmsförsörjningsenhet kan
utgöra en ledare för skadliga elektricitetsnivåer. Se till att inte
någon blottad ledningsdel från likströmsförsörjningsenheten
sticker ut från stiftplinten.
Service Personnel Warning
Warning
This equipment is to be installed and maintained by service personnel only
as defined by AS/NZS 3260 Clause 1.2.14.3 Service Personnel.
Waarschuwing
Deze apparatuur mag slechts geïnstalleerd en onderhouden worden door
servicepersoneel conform de definitie van AS/NZS 3260 Clausule 1.2.14.3
Service Personnel.
Varoitus
Attention
Tämän laitteen saa asentaa tai huoltaa ainoastaan Australiassa ja
Uudessa Seelannissa sovellettavan AS/NZS 3260 -standardin kohdan
1.2.14.3 Service Personnel määrittelemä huoltohenkilöstö.
Cet équipement ne doit être installé et entretenu que par du personnel
d’entretien comme défini par la réglementation AS/NZS 3260 Clause
1.2.14.3 Service Personnel.
Catalyst 2950 Desktop Switch Hardware Installation Guide
C-30
78-11157-03
Appendix C
Translated Safety Warnings
Service Personnel Warning
Warnung
Avvertenza
Dieses Gerät darf nur von Wartungspersonal gemäß AS/NZS-Definition
3260, Paragraph 1.2.14.3, "Service Personnel", installiert und gewartet
werden.
Questo apparecchio deve essere installato e mantenuto in efficienza
esclusivamente da personale tecnico che soddisfi i requisiti specificati
nella sezione 1.2.14.3 sul ‘Service Personnel’ contenuta nelle norme
AS/NZS 3260.
Advarsel
Installasjon og vedlikehold av dette utstyret skal kun foretas av
vedlikeholdspersonell som definert i AS/NZS 3260, klausul 1.2.14.3 Service
Personnel.
Aviso
Este equipamento deverá ser instalado e reparado apenas por pessoal de
manutenção qualificado, conforme estipulado em AS/NZS 3260 Cláusula
1.2.14.3 Service Personnel.
¡Advertencia!
Varning!
Este equipo se debe instalar y mantener solamente por personal de
servicio, según definido por AS/NZS 3260 Cláusula 1.2.14.3 Service
Personnel.
Installation och underhåll av denna utrustning får endast utföras av
servicepersonal enligt definition i AS/NZS 3260 klausul 1.2.14.3 Service
Personnel.
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
C-31
Appendix C
Translated Safety Warnings
Service Personnel Warning
Catalyst 2950 Desktop Switch Hardware Installation Guide
C-32
78-11157-03
I N D EX
Numerics
1000BASE-T GBIC modules (continued)
described 1-9
10/100/1000 ports
cable lengths 2-6
connecting to 2-33 to 2-36
illustrated 2-21
installing 2-20
1000BASE-X GBIC modules
connectors and cables B-3
cable lengths 2-6
described 1-7
connecting to 2-39 to 2-40
illustrated 1-6
connectors B-5
10/100 ports
described 1-8
cable lengths 2-6
illustrated 2-21
connecting to 2-33 to 2-36
installing 2-20
connectors and cables B-1 to B-2
100BASE-FX ports
described 1-6 to 1-7
cable lengths 2-6
illustrated 1-3
connecting to 2-37 to 2-38
1000BASE-SX ports
connectors and cables B-4 to B-5
cable lengths 2-6
described 1-8
connecting to 2-37 to 2-38
illustrated 1-4
connectors and cables B-4 to B-5
power levels, fiber-optic A-4
described 1-8
illustrated 1-5
power levels, fiber-optic A-4
1000BASE-T GBIC modules
A
AC power
cable lengths 2-6
connecting to 2-22
connecting to 2-41 to 2-42
connector 1-22
connectors B-5
specifications A-1 to A-2
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
IN-1
Index
adapter pinouts, terminal
RJ-45-to-DB-25 B-11
cables (continued)
GBIC
RJ-45-to-DB-9 B-10
1000BASE-T module 2-41
addresses, assigning IP 2-45
1000BASE-X module 2-39
agency approvals A-4, A-5
CWDM module 2-38
altitude A-1 to A-3
GigaStack module 2-42
autonegotiation
MT-RJ 1-8
10/100/1000 ports 1-7
problems, solving 3-3 to 3-4
10/100 ports 1-7
rollover B-12
straight-through
connecting to B-2, B-3
B
four twisted-pair pinout, 10/100 ports B-8
four twisted-pair pinout, 1000BASE-T
ports B-9
bandwidth utilization 1-17 to 1-20
brackets
two twisted-pair pinout B-7
See mounting brackets, attaching
twisted-pair
10/100/1000 ports 1-7
C
10/100 ports 1-6 to 1-7
cable guide, attaching 2-19
cables
See also connectors and cables
Catalyst 2950G-24-EI-DC service
warning 2-23, C-23 to C-24
10/100/1000 ports 1-7
cautions, defined xvi
10/100 ports 1-6 to 1-7
chassis warnings
crossover
against stacking 2-2, C-19 to C-20
connecting to B-2, B-3
rack-mounting, servicing 2-9, C-6 to C-10
four twisted-pair pinout, 10/100 ports B-8
Cisco IE2100 1-24
four twisted-pair pinout, 1000BASE-T
ports B-9
Cisco IE2100 Series Configuration Registrar
two twisted-pair pinout B-7
See Cisco IE2100
Cisco Intelligent Engine 2100
See Cisco IE2100
Catalyst 2950 Desktop Switch Hardware Installation Guide
IN-2
78-11157-03
Index
CiscoView 1-24
connecting (continued)
Class 1 laser product warning 2-4, C-21
to 100BASE-FX ports 2-37 to 2-38
clearance 2-7
to AC power 2-22
CLI 1-24
to console port 2-43 to 2-45
Cluster Builder application 1-23
to CWDM GBIC module ports 2-38
Cluster Management Suite
to DC power 2-23 to 2-32
See CMS
to GBIC module ports 2-38 to 2-43
Cluster Manager application 1-23
to GigaStack GBIC module ports 2-42
Cluster View application 1-23
to PC 2-43 to 2-45
CMS
to RPS 2-22
Cluster Builder 1-23
to terminal 2-43 to 2-45
Cluster Management 1-23
connection procedures 2-33 to 2-45
Cluster View 1-23
connectivity problems, solving 3-4
described 1-23
connectors and cables
Device Manager 1-23
Coarse Wave Division Multiplexing GBIC
modules
See CWDM GBIC modules
command-line interface
See CLI
configuration examples, network 1-1
configuring ports 2-45
connecting
to 10/100/1000 ports 2-33 to 2-36
to 10/100 ports 2-33 to 2-36
to 1000BASE-SX ports 2-37 to 2-38
to 1000BASE-T GBIC module ports 2-41
10/100/1000 ports B-3
10/100 ports B-1 to B-2
1000BASE-SX ports B-4 to B-5
1000BASE-T GBIC module ports B-5
1000BASE-X GBIC module ports B-5
100BASE-FX ports B-4 to B-5
console port B-6
GigaStack GBIC module ports B-6
power
AC 1-22
DC 1-22
RPS 1-23
See also cables
to 1000BASE-X GBIC module
ports 2-39 to 2-40
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
IN-3
Index
console port
D
adapter pinouts
RJ-45-to-DB-25 terminal B-11
DC power
connecting to 2-23 to 2-32
cable, rollover B-12
connector 1-22
console port (continued)
connecting to 2-43 to 2-45, B-10 to B-11
specifications A-3
default characteristics 2-43
warnings 2-23, 2-24, 2-26
illustrated 1-21 to 1-22
DC power disconnection warning 2-26, C-26
RJ-45-to-DB-9 adapter cable pinouts B-10
default characteristics of the console port 2-43
conventions, document xvi to xix
desk-mounting 2-20
crossover cable
Device Manager 1-23
connecting to
dimensions A-2 to A-3
10/100/1000 ports 2-34
documentation
10/100 ports 2-34
ordering xxi
1000BASE-T GBIC module ports 2-41
related publications xix to xx
URLs, Cisco xx
connectivity problems 3-4
document conventions xvi to xix
pinout
four twisted-pair, 10/100 ports B-8
duplex LED 1-14, 1-17
four twisted-pair, 1000BASE-T ports B-9
two twisted-pair B-7
CWDM GBIC modules
E
cable lengths 2-6
electrical noise, avoiding 2-7
connecting to 2-38
electromagnetic interface (EMI) A-4
described 1-9
EMC
installing 2-20
agency approvals A-4
regulatory statements 2-4 to 2-6
Catalyst 2950 Desktop Switch Hardware Installation Guide
IN-4
78-11157-03
Index
EMC regulatory statements 2-4 to 2-6
G
environmental ranges A-1 to A-3
Ethernet cable warning 2-23, C-25 to C-26
GBIC modules
examples, network configuration 1-1
cable lengths 2-6
exposed DC power wire warning 2-29,
cables
C-29 to C-30
1000BASE-T B-3
1000BASE-X 2-39
CWDM 2-38
F
GigaStack B-6
fan problems, solving 3-5
connecting to 2-38 to 2-43
features 1-1 to 1-3
connectors
feedback to Cisco Systems, web xxi
1000BASE-T B-4
fiber-port specifications A-4
1000BASE-X B-5
front panel
CWDM 2-38
10/100/1000 ports 1-7
10/100 ports 1-6 to 1-7
GBIC modules (continued)
GigaStack B-6
1000BASE-SX ports 1-8
described 1-8 to 1-9
100BASE-FX ports 1-8
illustrated
clearance 2-7
1000BASE-T 2-21
described 1-3
1000BASE-X 2-21
GBIC module ports 1-8 to 1-9
GigaStack 2-22
illustrated 1-3 to 1-6
module slots 1-4 to 1-5
LEDs 1-9 to 1-12
full-duplex LED 1-17
installing 2-20
Gigabit Interface Converters
See GBIC modules
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
IN-5
Index
GigaStack GBIC modules
installation (continued)
cable lengths 2-6
rack-mount 2-9 to 2-20
connecting to 2-42
shelf-mount 2-20
connectors and cables B-6
table-mount 2-20
described 1-9
warning 2-2, C-4
illustrated 2-22
installing GBIC modules 2-20 to 2-22
installing 2-20
IOS command-line interface
See CLI
ground connection warning 2-3, 2-24, C-15 to C-16
grounded equipment warning 2-3, 2-24,
IP address procedures 2-45
C-13 to C-14
J
H
jewelry removal warning 2-3, C-17 to C-18
half-duplex LED 1-17
HP OpenView 1-24
humidity A-1 to A-3
L
laser beam exposure warning 2-4, C-22
LEDs
I
color meanings 1-17 to 1-18
installation
duplex (DUPLX) 1-14, 1-17
cable guide 2-19
desk-mount 2-20
guidelines 2-6
package contents 2-7 to 2-9
POST 2-32
power on 2-22
front panel 1-9 to 1-12
full-duplex 1-17
half-duplex 1-17
interpreting 1-13, 1-17 to 1-18
port 1-13
port mode 1-14 to 1-16
pre-installation information and
guidelines 2-2 to 2-6
Catalyst 2950 Desktop Switch Hardware Installation Guide
IN-6
78-11157-03
Index
LEDs (continued)
port status 1-13
no on/off switch warning 2-2, C-12 to C-13
notes, defined xvi
RPS 1-13
speed (SPEED) 1-14, 1-18
status (STAT) 1-14, 1-17
O
system 1-12
obtaining documentation xx to xxii
utilization (UTIL) 1-14, 1-17
overtemperature warning 2-3, C-11 to C-12
lightning activity warning 2-3, C-3
P
M
package contents 2-7 to 2-9
main disconnecting device warning 2-3, C-5
patch cables, MT-RJ 1-8
management options 1-23 to 1-24
PC, connecting to switch 2-43 to 2-45, B-10
Mode button 1-14 to 1-16
performance problems, solving 3-3
mounting
personnel warning 2-2, C-20 to C-21
desk 2-20
physical dimensions A-2 to A-3
rack 2-9 to 2-20
pinouts
shelf 2-20
10/100/1000 ports B-4
table 2-20
10/100 ports B-2
mounting brackets, attaching 2-10 to 2-18
1000BASE-T GBIC port B-5
MT-RJ
adapters
connector B-4
patch cables 1-8
DB-25 B-11
console port
DB-25 adapter B-11
N
RJ-45-to-DB-9 adapter cable B-10
crossover cables
network configuration examples 1-1
four twisted-pair, 10/100 ports B-8
noise, electrical 2-7
four twisted-pair, 1000BASE-T ports B-9
two twisted-pair B-7
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
IN-7
Index
pinouts (continued)
power (continued)
RJ-45-to-DB-25 terminal adapter B-11
supply
RJ-45-to-DB-9 adapter cable B-10
AC connector 1-22
RJ-45-to-DB-9 PC adapter cable B-10
DC connector 1-22
straight-through cables
RPS connector 1-23
four twisted-pair, 10/100 ports B-8
power connectors 1-22 to 1-23
four twisted-pair, 1000BASE-T ports B-9
power on 2-22
two twisted-pair B-7
procedures
port
connecting to DC power 2-23 to 2-32
LEDs 1-9 to 1-12, 1-13
connection 2-33 to 2-45
mode
installation 2-9 to 2-20
changing 1-14 to 1-16
IP address 2-45
LEDs 1-9 to 1-12, 1-14 to 1-16
power on 2-22
selecting 1-14 to 1-16
ports
product disposal warning 2-3, C-14 to C-15
publications, related xix to xx
See 10/100 ports, 10/100/1000 ports,
100BASE-FX ports, GBIC module
ports, and console ports
Q
POST
description 2-32
qualified personnel warning 2-2, C-20 to C-21
problems, solving 3-5
results 2-32
R
power
agency approvals A-5
connecting to
rack-mounting
bracket mounting points 2-10 to 2-18
AC 2-22
procedures 2-9 to 2-20
DC 2-23 to 2-32
warning 2-9, C-6 to C-10
RPS 2-22
requirements A-1 to A-3
rear panel
clearance 2-7
console port connector 1-23
Catalyst 2950 Desktop Switch Hardware Installation Guide
IN-8
78-11157-03
Index
rear panel (continued)
status LED 1-14, 1-17
straight-through cable
described 1-20
connecting to
illustrated 1-21 to 1-22
10/100/1000 ports 2-34
power connectors 1-22 to 1-23
Redundant Power System
10/100 ports 2-34
1000BASE-T GBIC module ports 2-41
See RPS
regulatory statements, EMC 2-4 to 2-6
connectivity problems 3-4
related publications xix to xx
pinout
restricted access area warning 2-23, C-24 to C-25
four twisted-pair, 10/100 ports B-8
rollover cable B-12
four twisted-pair, 1000BASE-T ports B-9
RPS
two twisted-pair B-7
connecting to 2-22
SunNet Manager 1-24
connector 1-23
switch, power-on 2-22
described 1-23
system LED 1-12
LED 1-9, 1-13
warning 2-3, C-2
T
table-mounting 2-20
S
technical assistance xxii to xxiv
safety agency approvals A-4
technical specifications A-1 to A-5
safety warnings 2-2 to 2-4, C-1 to C-31
Telnet, and accessing the CLI 1-24
service personnel warning 2-2, C-30 to C-31
temperature
shelf-mounting 2-20
operating A-1 to A-3
SNMP network management platforms 1-24
warning 2-3, C-11 to C-12
software switch management 1-23 to 1-24
specifications A-1 to A-5
speed LED 1-14, 1-18
stacking the chassis warning 2-2, C-19 to C-20
terminal, connecting to a switch 2-43 to 2-45,
B-11
terminal-emulation software 2-43
translated warnings C-1 to C-31
Catalyst 2950 Desktop Switch Hardware Installation Guide
78-11157-03
IN-9
Index
troubleshooting 3-1
diagnosing problems 3-2 to 3-5
understanding POST results 3-2
U
URLs, Cisco xx
utilization
bandwidth 1-17 to 1-20
LED 1-14, 1-17
V
verifying package contents 2-7 to 2-9
W
warnings
DC power 2-23, 2-24, 2-26
defined xvii to xix
installation 2-2 to 2-4
translated C-1 to C-31
Catalyst 2950 Desktop Switch Hardware Installation Guide
IN-10
78-11157-03