IP Link® Device Interface
Communication Sheet
eiki_1_4323_1.pke
Revision: 6/16/2010
This document provides additional assistance with wiring your Extron IP Link enabled product to your device.
Different components may require a different wiring scheme than those listed below.
For complete operating instructions, refer to the user's manual for the specific Extron IP Link enabled product or
the controlled device manufacturer supplied documentation.
Device Specifications:
Device Type:
Manufacturer:
Firmware Version:
Model(s):
Video Projector
Eiki
N/A
LC-XBL30, LC-XBL20, LC-XBL25
Version History:
Driver
Version
1
Date
6/9/2010
IP Link
Compiler
GC
Version
1.4.0
3.0.3
Notes
Initial version.
Driver Notes:
Page 1 of 5
IP Link® Device Interface
Communication Sheet
eiki_1_4323_1.pke
Revision: 6/16/2010
Control Commands & States:
Aspect Ratio
Normal
Wide
D. Zoom +
D. Zoom Audio Mute
On
Off
Auto Image
Execute
Freeze
On
Off
Input
Computer 1
Computer1 (A) RGB
Computer1 (YPbPr)
Computer1 Scart
Computer1 S-Video
Computer 2
Video
Power Control
On
Off
Video Mute
On
Off
Volume (Discrete)
0 to 63 in steps of 1
Volume (Step)
Up
Down
Page 2 of 5
IP Link® Device Interface
Communication Sheet
eiki_1_4323_1.pke
Revision: 6/16/2010
Status Available:
Aspect Ratio
Normal
Wide
D. Zoom +
D. Zoom Audio Mute
On
Off
Connection Status
Connected
Disconnected
Device Status
Normal
Power Fail
Cooling Down (Abnormal
Temp)
Cooling Down (Lamp
Failure)
Power Save (Cooling
Down)
Power Save
Standby (Lamp Failure)
Temp Warning and
Recovered
Status Unavailable
Freeze
On
Off
Input
Computer 1
Computer 2
Lamp Usage
Hours
Power Control
On
Off
Power Status
On
Off
Cooling Down
Status Unavailable
Video Mute
On
Off
Volume (Discrete)
0 to 63 in steps of 1
Page 3 of 5
Video
Warming Up
IP Link® Device Interface
Communication Sheet
eiki_1_4323_1.pke
Revision: 6/16/2010
MLC62 Supported Commands:
Aspect Ratio
Normal
Wide
D. Zoom +
D. Zoom Audio Mute
On
Off
Auto Image
Execute
Freeze
On
Off
Input
Computer 1
Computer1 (A) RGB
Computer1 (YPbPr)
Computer1 Scart
Computer1 S-Video
Computer 2
Video
Power Control
On
Off
Video Mute
On
Off
Volume (Discrete)
0 to 63 in steps of 1
Volume (Step)
Up
Down
Page 4 of 5
eiki_1_4323_1.pke
IP Link® Device Interface
Communication Sheet
Revision: 6/16/2010
Cable and Adapter Requirements:
F/F Null Modem Serial Cable
Notes for the Device:
By default, the projector’s power management is set to be in Eco mode. In order to use the RS232 communication,
you need to change the Power Management to Network Mode. To enable the network mode, the steps are as follows:
Menu->Settings->Standby mode->Network
Serial communication:
Port Type: RS-232
Baud Rate: 19200
Data Bits: 8
Parity: None
Stop Bits: 1
Flow Control: None
Pin Assignments Diagram:
Note: Captive screw connector may also be used as a serial connection.
General Notes:
Page 5 of 5