Electrolux COMPETENCE D5701-5 Operating instructions

COMPETENCE D5701-5
Built-in Electric Multifunction Double Oven
Installation and Operating Instructions
12.00
PERFEKT IN FORM UND FUNKTION
IMPORTANT SAFETY INFORMATION
These warnings are provided in the interests of your
safety. Ensure that you understand them all before
installing or using the appliance. Your safety is of
paramount importance. If you are unsure about any
of the information in this book contact the Customer
Care Department.
The appliance must be installed according to the
instructions supplied. The installation work must be
undertaken by a qualified electrician or competent
person.
The appliance should be serviced by an authorised
Service Engineer and only genuine approved spare
parts should be used.
The appliance must be installed in an adequately
ventilated room.
It is imperative that the appliance is left in the base to
protect both the appliance and the floor.
This appliance is heavy and care must be taken
when moving it.
Do not attempt to lift or move this appliance by the
handles.
All packaging, both inside and outside the appliance
must be removed before the appliance is used.
It is dangerous to alter the specifications or modify
the appliance in any way.
After installation please dispose of the packaging
with due regard for safety and the environment. Your
local authority can arrange this.
Do not leave the grill pan handle in position when
grilling as it will become hot.
Always support the grill pan when it is in the withdrawn
or partially withdrawn position.
During use the appliance becomes hot. Care should
be taken to avoid touching heating elements inside the
oven.
Ensure that all vents are not obstructed to ensure
ventilation of the oven cavity.
Never line any part of the appliance with foil.
Always stand back from the appliance when opening
the doors to allow any build up of steam or heat to
release.
Do not stand too close to the oven or grill while in
use as warm air will exhaust from the grill cavity and
the vents on the front frame of the appliance.
Stand clear when opening the drop down doors.
Support the doors using the handles until fully open.
Never leave the appliance unattended when the
oven door is open.
Do not place sealed cans or aerosols inside the oven.
They may explode if they are heated.
Ensure that all control knobs are in the OFF position
when not in use.
Do not stand on the appliance or on the open oven
doors.
Do not hang towels, dishcloths or clothes from the
appliance or its handles. They are a safety hazard.
Do not use this appliance if it is in contact with water.
Never operate it with wet hands.
CHILD SAFETY
CLEANING AND MAINTENANCE
INSTALLATION
Do not allow children to play with any part of the
packaging.
Do not allow children to sit or climb on the drop down
doors.
This appliance is not intended for use by children and
other persons whose physical, sensory or mental
capabilities or lack of experience and knowledge
prevents them from using the appliance safely
without supervision or instruction by a responsible
person to ensure that they can use the appliance
safely.
Children should be supervised to ensure that they do
not play with the appliance.
CAUTION: Accessible parts may be hot when the
grill is in use. Young children should be kept
away.
For hygiene and safety reasons this appliance
should be kept clean at all times. A build-up of
fats or other foodstuffs could result in a fire
especially in the grill pan.
Do not leave the cookware containing foodstuffs, e.g.
fat or oil in the appliance in case it is inadvertently
switched on.
Always allow the appliance to cool before switching off
at the wall prior to carrying out any cleaning /
maintenance work.
Only clean this appliance in accordance with the
instructions given in this book.
Never use steam or high pressure steam cleaners to
clean the appliance.
AT THE END OF THE APPLIANCE'S LIFE
DURING USE
The symbol
on the product or on its packaging
indicates that this product may not be treated as
household waste. Instead it shall be handed over to
the applicable collection point for the recycling of
electrical and electronic equipment. By ensuring this
product is disposed of correctly, you will help prevent
potential negative consequences for the environment
and human health, which could otherwise be caused
by inappropriate waste handling of this product. For
more detailed information about recycling of this
product, please contact your local city office, your
household waste disposal service or the shop where
you purchased the product.
This appliance is not intended to be operated by
means of an external timer or separate remote
control system.
This appliance has been designed for domestic use
to cook edible foodstuffs only and must not be used
for any other purposes.
Take great care when heating fats and oils as they
will ignite if they become too hot.
Never place plastic or any other material which may
melt in or on the oven.
Always use oven gloves to remove and place food in
the oven.
2
CONTENTS
FOR THE USER
Important Safety Information
Description Of The Appliance
Getting To Know Your Appliance
Grill And Oven Furniture
Telescopic Runners
Before Using The Appliance
Rating Plate
Preparing To Use Your Appliance
When First Switching On
The Cooling Fan For The Controls
Control Panel Indicator Neon(s)
Pop In Pop Out Controls
Condensation And Steam
Cookware
Helpful Hints When Buying And Preparing Food
2
4
5
6
6
7
7
7
7
7
7
7
7
7
7
Electronic Timer
Other Functions
8
12
Full Width Dual Grill
Using Full Width Dual Grill
Things To Note
The Grill Pan and Handles
Hints And Tips
Grilling Chart
13
13
13
14
14
15
Second Oven
Using Second Oven
Things to Note
To Fit The Second Oven Shelf
Hints And Tips
16
16
16
16
17
Second Oven Cooking Chart
18
Ventitherm ® Precision Fan Cooking
Using Ventitherm ® Precision Fan Cooking
Things To Note
To Fit The Main Oven Shelves
Using the Telescopic Runners (Where Fitted)
Hints And Tips
19
19
19
19
20
20
Conventional Cooking
Using Conventional Cooking
Things To Note
Hints And Tips
21
21
21
22
Main Oven Cooking Chart
Roasting Chart
23
24
Main Oven Full Width Grill
Using Full Width Grill
Things to Note
Hints And Tips
Grilling Chart
25
25
25
26
26
Pizza
Using Pizza
Things To Note
Hints And Tips
27
27
27
27
Rotitherm Roasting
Using Rotitherm Roasting
Things To Note
Hints And Tips
28
28
28
29
Rotitherm Roasting Chart
29
Speedcook
Using Speedcook
Selecting Speedcook
Things To Note
30
30
30
30
Fan Controlled Defrosting
Using Fan Controlled Defrosting
Things To Note
Hints And Tips
31
31
31
31
Care and Cleaning
Cleaning Materials
Cleaning The Outside Of The Appliance
Removing And Replacing Wirework Runners
Cleaning Inside The Ovens
Cleaning The Door(s)
To Remove The Inner Glass
To Clean The Inner Glass Door Panel
To Replace the Inner Glass Door Panel
Cleaning The Grill And Oven Furniture
Replacing An Oven Light Bulb
32
32
32
32
33
34
34
34
35
35
35
Something Not Working
Service and Spare Parts
Guarantee Conditions
37
38
39
FOR THE INSTALLER
Technical Details
Installation Instructions
Warnings
Things To Note
Choice Of Electrical Connection
Preparing Cabinet For Fitting Of Oven
Recommended Cabinet Dimensions
How To Finish Unpacking
To Remove Cover Of Mains Terminal
Connecting To The Mains Terminal
Checking Electrical Connections
Connecting To A Hob Or Cooker Point
Fitting Into The Cabinet
Notes
40
41
41
41
42
42
43
44
44
45
45
45
46
47
To help you the following symbols will be found in the
text.
Hints and Tips
Safety Instructions
Please read the instruction book carefully before
use and retain for future reference.
3
DESCRIPTION OF THE APPLIANCE
BUILT-IN ELECTRIC MULTIFUNCTION DOUBLE OVEN
Electronic Timer
12.00
Control Panel
Second Oven/Grill
Main Oven
Your built-in oven comprises of a conventional second oven and dual grill in the top compartment.
The multifunction oven can be automatically controlled by the electronic timer.
4
GETTING TO KNOW YOUR APPLIANCE
THE CONTROL PANEL
A B
CD
F
E
12.00
K
A
B
C
-
L
Second Oven/Grill Function Selector
Second Oven/Grill Function Selector Neon
Multifunction Selector
Oven Light
Full Width Grill
Single Economy Grill
Ventitherm ® Precision Fan Cooking
Conventional Cooking
Rotitherm Roasting
Pizza
Fan Controlled Defrosting
D
E
F
G
H
I
J
K
L
M
-
Multifunction Selector Neon
Electronic Timer
Main Oven Temperature Neons
Main Oven Increase/Decrease Selector
Main Oven Increase/Decrease Selector Neon
Second Oven Temperature Control
Second Oven Temperature Control Neon
Speedcook Button
Time/Temperature Button
Time Selector Button
5
M
G H
I
J
GRILL AND OVEN FURNITURE
TELESCOPIC RUNNERS
Your appliance may be fitted with telescopic runners
in the grill and main oven.
To fit the shelf into the telescopic runner,
The following items of oven furniture have been
supplied with the appliance:-
1. Ensure the telescopic runners are pushed back
into the oven cavity before fitting the shelf.
2. Holding the front edge of the shelf with both
hands, place the rear shelf forms over the
telescopic runners.
1 grill pan
3. Slide the shelf into position, lifting slightly at the
front so that the shelf locates into the retaining
hooks.
To remove, raise the front edge and withdraw the
shelf.
2 grill pan handles
FORM
RETAINING
HOOK
1 grill pan grid
1 straight shelf
(for grilling and
second oven
cooking)
3 straight shelves
(for main oven
cooking)
6
BEFORE USING THE APPLIANCE
RATING PLATE
POP IN POP OUT CONTROLS
This is situated on the lower front frame of the
appliance and can be seen upon opening the door.
Alternatively the rating plate may also be found on
the back or top of some models (where applicable).
The appliance must be protected by a suitably rated
fuse or circuit breaker. The rating of the appliance is
given on the rating plate.
These control knobs can remain flush with the control
panel when not in use, or pushed and released to
stand out from the panel for easy operation.
CONDENSATION AND STEAM
When food is heated it produces steam similar to a
boiling kettle. The vents allow some of this steam to
escape. However, always stand back from the
appliance when opening the door(s) to allow any
build up of steam or heat to release.
If the steam comes into contact with a cool surface
on the outside of the appliance, e.g. a trim, it will
condense and produce water droplets. This is quite
normal and is not caused by a fault on the appliance.
To prevent discolouration, regularly wipe away
condensation and also soilage from surfaces.
Do not remove the rating plate from the appliance
as this may invalidate the guarantee.
PREPARING TO USE YOUR APPLIANCE
Wipe over the base of the oven(s) with a soft cloth
and hot soapy water and wash the furniture before
use.
We suggest that you run the oven elements for 10 –
15 minutes at 220°C to burn off any residue from
their surfaces.
The procedure should be repeated with the grill for
approximately 5 – 10 minutes.
During this period an odour may be emitted, it is
therefore advisable to open a window for ventilation.
COOKWARE
Baking trays, dishes etc., should not be placed
directly against the grid covering the fan at the back
of the oven.
WHEN FIRST SWITCHING ON
Do not use baking trays larger than 30cm x 35cm
(12” x 14”) as they will restrict the circulation of heat
and may affect performance.
The oven has a 24 hour clock. When the oven is first
switched on at the wall the electronic display will
automatically show 12.00, and the 'Time' (
) neon
will also flash.
HELPFUL HINTS WHEN BUYING AND
PREPARING FOOD
THE COOLING FAN FOR THE CONTROLS
The cooling fan comes on immediately when the
grill/top oven is switched on and after a short time
when the main oven is in use. It runs on after the
controls are switched off until the appliance has
cooled. During the initial period the cooling fan for
the main oven may turn ON and OFF, this is quite
normal.
Care must be taken when handling foods in the
home. Always follow the basic rules of food hygiene
to prevent bacterial and microbial growth and cross
contamination when preparing, reheating, cooking,
cooling, defrosting and freezing foods:1. Avoid buying chilled or frozen products if you
cannot store them straight away. The use of an
insulated container when shopping is advisable.
Always allow the cooling fan to cool the
appliance down before switching off at the
wall prior to carrying out any cleaning or
maintenance work.
2. When you arrive home, place perishable foods in
the refrigerator or freezer immediately. Ensure
they are well covered to prevent them drying out
and to prevent any possible cross contamination
with bacteria from raw to cooked foods.
CONTROL PANEL INDICATOR NEON(S)
3. In the kitchen keep work tops, chopping boards
and utensils clean with hot soapy water between
preparation stages. Ideally, keep one chopping
board for raw meat and another for other foods.
Keep your dish cloths and tea towels clean.
The indicator neon will operate when the grill (where
applicable) or oven(s) is switched on. The indicator
neon will glow. It may turn on and off during use to
show that the setting is being maintained. If the neon
does not operate as the instructions indicate the
controls have been incorrectly set.
Return all
controls to zero and reset following the instructions
for the required setting.
7
ELECTRONIC TIMER
D
C
KEY
A
12.00
COOK TIME INDICATOR NEON
B
SPEEDCOOK INDICATOR NEON
C
END TIME INDCATOR NEON
D
COUNTDOWN INDICATOR NEON
E
TEMPERATURE INDICATOR NEON
F
TIME INDICATOR NEON
G
TIME SELECTOR BUTTON
H
TIME/TEMPERATURE BUTTON
I
SPEEDCOOK BUTTON
B
A
I
H
12.00
NOTE:
The time of day must be set before the main oven
will operate manually.
Fig.1
1. HOW TO SET THE TIME OF DAY
The oven has a 24 hour clock.
When the electricity supply is first switched ON, the
display will show 12.00 and the 'Time' indicator neon
(
) will flash as Fig. 1.
To set the correct time turn the main oven
increase/decrease selector ( +/- ) until the correct
time on the 24 hour clock is reached, e.g. 10.00am
as Fig.2. The 'Time' indicator neon (
) will flash
for 5 seconds and then go out.
10.00
Fig.2
Note: The main oven increase/decrease selector
will operate slowly at first, and then more rapidly.
2. HOW TO SET THE COUNTDOWN
The 'Countdown' gives an audible reminder at the
end of any period of cooking. This cooking period
may be up to 99 mins. It is not part of the automatic
control.
To set, press the Time Selector button (
) until the
'Countdown' indicator neon (
) is illuminated the
display reads 0.00 as Fig.3.
To set the correct time duration turn the main oven
increase/decrease selector ( +/- ) until the display
indicates the interval to be timed, e.g. 20 mins as Fig.
4.
0.00
Fig.3
NOTE: This must be completed within 5 seconds
of first pressing the Time Selector button.
20.00
To view the remaining time period, press the time
selector button until the 'Countdown' neon flashes.
When 90% of the time set has elapsed an audible
signal sounds. The 'Countdown' will sound
intermittently for up to 2 minutes at the end of the
timed period. The sound can be stopped by pressing
any button.
Fig.4
8
E
F
G
TO CANCEL THE COUNTDOWN
If you change your mind and want to cancel the
'Countdown', press the Time Selector button until the
'Countdown' (
) indicator neon flashes and then
turn the main oven increase/decrease selector ( +/- )
until 0.00 shows in the display as Fig. 5. The
'Countdown' ( ) indicator neon will continue to flash
for a few seconds and then return to the time of day.
0.00
Fig.5
3. SETTING THE OVEN TIMER
CONTROL
The main oven only can be automatically timed.
When using the timer control for the very first time, it
is advisable to let it operate while you are at home.
The displays can be checked to show that it is
operating correctly and you will feel confident to
leave a meal to cook automatically in the future.
9.00
A) TO SET THE TIMER TO SWITCH ON
AND OFF AUTOMATICALLY
i)
ii)
iii)
iv)
v)
vi)
Ensure the electricity supply is switched ON and
that the correct time of day is displayed, e.g.
9.am. as Fig. 6.
Set the main oven controls to the required
function and temperature.
Place food in the oven.
To set the length of cooking time, press the Time
Selector button until the 'Cook Time' indicator
neon is illuminated (
). Turn the main oven
increase/decrease selector ( +/- ) until the
required length of cooking time is displayed, e.g.
2 hrs 15 mins as Fig. 7.
The maximum cooking time is 9.59 hours.
Release the buttons. The 'Cook Time' indicator
neon (
) will be illuminated.
Fig.6
2.15
Remember, this must be completed within 5
seconds of first pressing the Time Selector
button.
Fig.7
vi) To set the 'End Time'. Press the Time Selector
button until the 'End Time' indicator neon (
)
flashes. Turn the main oven increase/decrease
selector ( +/- ) until the required stop time is
displayed, e.g. 12.15 p.m. as Fig. 8.
vii) Release the buttons. The 'Cook Time' (
)
and 'End Time' (
) indicator neons will be
illuminated. To return the display to the time of
day, press the Time/Temperature button.
The 'End Time' must not be more than 23 hours
59 minutes from the time of day. For example, if
the time of day is 09.00a.m., the latest 'End Time'
would be 08.59a.m. the next day.
12.15
Fig.8
NOTE: The Multifunction Selector neon and the
main oven Increase/Decrease Selector neon (
)
will remain illuminated during programme.
9
B) TO SET THE TIMER TO SWITCH OFF
ONLY
10.00
i) Ensure the electricity supply is switched ON and
that the correct time of day is displayed, e.g.
10.00am as Fig. 9.
ii) Set the main oven controls to the required
function and temperature.
Fig.9
iii) Place food in the oven.
iv) To set the length of cooking time, press the Time
Selector button until the 'Cook Time' (
)
indicator neon is illuminated. Turn the main oven
increase/decrease selector ( +/- ) until the
required length of cooking time is displayed, e.g. 2
hrs 15 mins as Fig. 10.
2.15
v) Release the buttons. The 'Cook Time' indicator
neon (
) will illuminate.
Fig.10
vi) To check the 'End Time' during the cooking
period, simply press the Time Selector Control
button once and the remaining time will be
displayed, as Fig. 11.
vii) To return the display to the time of day, press the
Time/Temperature button.
2.15
NOTE: The Multifunction Selector neon and the
main oven Increase/Decrease Selector neon (
)
will remain illuminated during programme.
4. TO CANCEL AN AUTOMATIC
PROGRAMME
Fig.11
i)
To cancel an automatic programme press
the Time Selector button until the 'Cook Time'
(
) indicator neon flashes. Turn the main oven
increase/decrease selector ( +/- ) until the
display reads 0.00 as Fig. 12.
ii)
Release the buttons. The 'Cook Time' (
indicator neon will flash.
02
.0
05
1
.1
)
iii) Turn off the oven controls.
iv) The display will return to the time of day.
Fig.12
Fig.13
5. TO RETURN THE APPLIANCE TO
MANUAL
At the end of a timed cooking period, the
indicator neon will flash and an alarm will sound
for up to 2 minutes.
i)
To stop the sound press any of the buttons, as
Fig. 13.
ii)
---°C will show in the display.
iii) Turn off the oven controls.
10
6. THINGS TO NOTE
•
In the event of an interruption of the electricity
supply, the timer will reset itself to 12.00, and all
programming will be cancelled.
7. AUTOMATIC COOKING
It is advisable to leave food in the oven for as
short a time as possible before automatic
cooking. Always ensure commercially prepared
food is well within its use by date and that home
prepared food is fresh and of good quality.
When cooking is complete, do not leave food to
stand in the oven, but remove and cool it quickly
if the food is not to be consumed immediately.
Always ensure food in the oven has been
covered before cooking if it is not possible to
remove food immediately after cooking.
OTHER FUNCTIONS
SWITCHING OFF THE DISPLAY
You can save energy by switching off the clock
display.
SWITCHING OFF THE CLOCK DISPLAY
1. Turn the main oven increase/decrease selector
( +/- ) to the right and hold it.
2. In addition press the Time Selector button (
until the display goes out as Fig. 14.
)
Fig.13
As soon as the appliance is switched on again,
the display comes on automatically.
SWITCHING ON THE CLOCK DISPLAY
1. Turn the main oven increase/decrease selector
( +/- )to the right and hold it.
2. In addition press the Time selector button (
until the display appears again.
)
11
CHILD SAFETY DEVICE
To avoid children switching on the main oven when
the appliance is switched off, it is possible to lock the
oven controls in the main oven only.
THE MAIN OVEN CHILD SAFETY DEVICE
The oven cannot be used from the moment the child
safety device has been switched on.
ACTIVATING THE CHILD SAFETY DEVICE
•
•
•
No oven function must be selected.
Turn the main oven increase/decrease selector
( +/- ) to the left and hold it. In addition press
the Time Selector button (
) until "SAFE"
appears in the display.
The child safety device is now activated.
DEACTIVATING THE CHILD SAFETY DEVICE
•
•
Turn the main oven increase/decrease selector
( +/- ) to the left and hold it. In addition press
the Time Selector button (
) until "SAFE"
disappears from the display.
The child safety device is now deactivated and
the oven is again ready for use.
OVEN SAFETY CUT-OUT
If not switched off after a certain time, or if the
temperature is not modified, the oven switches off
automatically.
The last temperature set flashes in the temperature
display.
The oven switches off when the oven temperature
is :*
30
-
120°C
after
12.5
hours
120
-
200°C
after
8.5
hours
200
-
250°C
after
5.5
hours
250
-
Max°C
after
1.5
hours
Switching on after a safety cut-out
Switch the oven off completely.
It can then be switched on again.
The safety cut-out is cancelled if the clock function
Cook time (
) or End Time (
) is set.
*Not with the Rotitherm Roasting oven function.
12
FULL WIDTH DUAL GRILL
CAUTION – ACCESSIBLE PARTS MAY BE HOT WHEN THE GRILL IS IN USE. YOUNG CHILDREN
SHOULD BE KEPT AWAY.
The Dual Grill on this appliance has been designed to heat up more quickly than conventional grill elements. It
provides quick, direct heat and no preheating is necessary. It has a dual circuit facility which means that the full
area of the grill can be used, or for economy purposes the centre section only can be used when cooking smaller
quantities of food.
USING FULL WIDTH DUAL GRILL
12.00
•
•
•
•
To operate the grill, pop out and turn the second
oven/grill function selector for full grill.
Pop out and turn the second oven/grill function
selector for centre section only.
Turn the temperature control knob to the right as
far as it will go. This is the hottest setting.
To use the grill at lower settings, turn the
temperature control knob so that 110°C or 150°C
on the panel lines up with the "0" on the knob.
THINGS TO NOTE
•
•
•
•
The indicator neon will glow. It may turn ON and
OFF during use to show that the setting is being
maintained.
The cooling fan for the controls may operate after
a time.
Some smoke from fat splashes may be evident
as the grill cleans itself.
The grill may be used with the door open or with
the door closed.
13
THE GRILL PAN AND HANDLES
1.
The grill pan is supplied with removable handles.
1.
To attach the handles, place the wirework
under the cut out in the pan so that the metal
plate hooks over the top of the grill pan.
Ensure the handles are positively located.
2.
To remove the handles, lift away from the cut
out on the grill pan.
2.
Place the grill pan on the shelf so that the pan is
positioned centrally beneath the grill.
Protect your hands when removing the grill
pan handles.
Always remove the grill pan handles during
grilling.
To check the progress of the food being grilled, the
grill pan should be withdrawn to attend food during
cooking.
If your model is fitted with telescopic runners in
position 3, the grill pan can be withdrawn on the
shelf.
HINTS AND TIPS
•
•
•
•
•
•
Most foods should be placed on the grid in the
grill pan to allow maximum circulation of air to lift
the food out of the fats and juices.
Adjust the grid and grill pan runner position to
allow for different thicknesses of food. Position
the food close to the element for faster cooking
and further away for more gentle cooking.
Food should be thoroughly dried before grilling to
minimise splashing. Brush lean meats and fish
lightly with a little oil or melted butter to keep
them moist during cooking.
Accompaniments such as tomatoes and
mushrooms may be placed around the outer
edges or underneath the grid when grilling
meats.
When toasting bread, we suggest that the top
runner position is used with the grid in its 'high'
position.
When using the centre section grill, ensure food
is placed centrally on the grilling grid directly
beneath the grill element.
14
•
•
Preheat the grill on full setting for a few minutes
to seal meat or for toasting. Adjust the heat
setting and the shelf position as necessary during
cooking.
The food should be turned over during cooking
as required.
GRILLING CHART
FOOD
POSITION
Bacon Rashers
Beefburgers
Chicken Joints
Chops – Lamb
Pork
GRILL TIME
(mins in total)
5-6
Adjust
grill
setting
and
10 - 15
30 - 40
15 - 20
20 - 30
Fish – Whole
Trout/Mackerel
grill
Fillets Plaice/Cod
pan
10 - 15
Kebabs
grid
20 - 30
Kidneys –
Lamb/Pig
to
8 - 12
Liver –
Lamb/Pig
suit
15 - 25
10 - 20
different
Sausages
Steaks – Rare
Medium
Well Done
Toasted
Sandwiches
20 - 30
thicknesses
of
food
6 - 12
12 - 16
14 - 20
3-4
The times quoted above are given as a guide and
should be adjusted to suit personal taste.
15
SECOND OVEN
The second oven is the smaller of the two ovens. It is heated by elements in the top and bottom of the oven. It is
designed for cooking smaller quantities of food. It gives especially good results if used to cook fruit cakes, sweet
and savoury flans or quiche.
The second oven is also ideal for use as a warming compartment to warm dishes and keep food hot. Use the
second oven when you want to warm plates. Use the lowest setting on the second oven temperature control.
USING SECOND OVEN
12.00
•
•
Pop out and turn the second oven/grill function
selector to.
Pop out and turn the second oven temperature
control to the required setting.
THINGS TO NOTE
•
•
•
The oven light will illuminate.
The indicator neon will glow. It may turn ON and
OFF during use to show that the setting is being
maintained.
The cooling fan for the controls may operate after
a time.
Do not place dishes, tins or baking trays
directly onto the oven base as it becomes
very hot and damage may occur.
TO FIT THE SECOND OVEN SHELF
The shelf should be fitted with the straight rods
uppermost on the frame and the forms towards the
back of the oven.
To remove a shelf slide the shelf towards you until
the shelf stop is reached. Tilt shelf up at the front so
that the stops clear the side supports. Lift shelf clear.
To install a shelf, reverse the above steps. Each
shelf position has an upper and lower support wire,
ensure the shelf is placed between these two support
wires.
16
HINTS AND TIPS
•
•
•
•
•
•
•
•
Arrange the shelf in the required position before
switching the oven ON. Shelf positions are
counted from the bottom upwards.
There should always be at least 2.5cm (1”)
between the top of the food and the element.
This gives best cooking results and allows room
for rise in yeast mixtures, Yorkshire puddings etc.
When cooking cakes, pastry, scones bread etc.,
place the tins or baking trays centrally on the
shelf.
Ensure that food is placed centrally on the shelf
and there is sufficient room around the baking
tray/dish to allow for maximum circulation.
Stand dishes on suitably sized baking trays on to
prevent spillage onto the oven base and to help
reduce cleaning.
The material and finish of the baking tray and
dishes used will affect base browning.
Enamelware, dark, heavy or non-stick utensils
increase base browning. Shiny aluminium or
polished steel trays reflect the heat away and
give less base browning.
Do not place baking trays directly on the oven
base as it interferes with the oven air circulation
and can lead to base burning; use the lower shelf
position.
Because of the smaller cooking space and lower
temperatures, shorter cooking times are
sometimes required. Be guided by the
recommendations given in the cooking chart.
For economy leave the door open for the shortest
possible time, particularly when placing food into
a pre-heated oven.
Do not place cookware and cooking pots
with rough bases e.g. cast iron on the oven
door as damage to the glass may occur.
17
SECOND OVEN COOKING CHART
SECOND OVEN
FOOD
Biscuits
Bread
Bread rolls/buns
Cakes:
Small & Queen
Sponges
Victoria Sandwich
Madeira
Rich Fruit
Christmas
Gingerbread
Meringues
Flapjack
Shortbread
Casseroles:
Beef/Lamb
Chicken
Convenience Foods
Fish
Fish Pie (Potato Topped)
Fruit Pies, Crumbles
Milk Puddings
Pasta Lasagne etc.
Pastry:
Choux
Eclairs, Profiteroles
Flaky/Puff Pies
Shortcrust
Mince Pies
Meat Pies
Quiche, Tarts, Flans
Roasting Meat, Poultry
Scones
Shepherd’s Pie
Soufflés
Vegetables:
Baked Jacket Potatoes
Roast Potatoes
Yorkshire Puddings: Large
Individual
SHELF
POSITION
1
1*
1
1
1
1
1
1
1
1
1
1
1
1*
1*
1
1*
1
1
1
1
1
1*
1
1*
1
1*
1
1*
1
1
1
1
1
COOKING
TEMP°C
170 - 190
200 - 220
200 - 220
180 - 190
160 - 170
160 - 170
140 - 150
140 - 150
130 - 140
APPROX
COOK TIME (m)
10 - 20
25 - 30
15 - 20
18 - 25
18 - 20
18 - 25
1¼ - 1½h
2¼ - 2½h
3 - 4½h
depends on size
140 - 150
1¼ - 1½h
90 - 100
2½ - 3h
170 - 180
25 - 30
140 - 150
45 - 65
140 - 160
2½ - 3h
180 - 190
1¼ - 1½h
Follow manufacturer’s instructions
170 - 190
20 - 30
190 - 200
20 - 25
190 - 200
40 - 50
140 - 150
1½ - 2h
170 - 180
40 - 45
180 - 190
30 - 35
170 - 180
20 - 30
210 - 220
25 - 40
190 - 200
15 - 20
190 - 210
25 - 35
180 - 200
25 - 45
160 - 180
see roasting chart
220 - 230
8 - 12
190 - 200
30 - 40
170 - 180
20 - 30
180 - 190
1 - 1½h
180 - 190
1 - 1½h
200 - 210
25 - 40
200 - 210
15 - 25
* = Shelf on the oven base
Note: Shelf positions are counted from the bottom of the oven upwards.
18
VENTITHERM ® PRECISION FAN COOKING
The fan oven is particularly suitable for cooking larger quantities of food.
The advantages of fan oven cooking are:
PREHEATING
The fan oven quickly reaches its temperature, so it is not usually necessary to preheat the oven. Without
preheating however, you may need to add an extra 5 – 10 minutes on the recommended cooking times. For
recipes needing high temperatures, e.g. bread, pastries, scones, soufflés etc., best results are achieved if the oven
is preheated first. For best results when cooking frozen or cooked chilled ready meals always preheat the oven
first.
COOKING TEMPERATURES
Fan oven cooking generally requires lower temperatures than conventional cooking. Follow the temperatures
recommended in the cooking chart. As a guide reduce temperatures by 20°C - 25°C for your own recipes, using a
conventional oven.
BATCH BAKING
The fan oven cooks evenly on all shelf levels, especially useful when batch baking.
USING VENTITHERM ® PRECISION FAN COOKING
12.00
•
•
•
•
Pop out and turn the multifunction selector to
Ventitherm ® Precision Fan Cooking.
Wait 5 seconds until your choice is confirmed.
The temperature will automatically set to 150°C.
•
If you wish to alter the set temperature, you may
do so by pushing out and turning the main oven
increase/decrease selector (+/-) until the required
temperature setting is reached.
•
THINGS TO NOTE
•
•
•
If it is necessary to reach the required
temperature in a shorter time, the Speedcook
Function can be used. See Speedcook Function
section.
•
When the required temperature is reached the
three temperature indicator neons on the timer
display will illuminate and an audible signal will
sound.
•
19
The multifunction selector indicator neon and the
main oven increase/decrease selector indicator
neon will glow.
The main oven temperature neons will illuminate
until the oven has reached the desired
temperature and then stop. When the oven has
been switched off the bars that are still lit indicate
the remaining residual heat in the oven.
The cooling fan for the controls may operate after
a time.
The oven light will illuminate.
If an automatic programme has been set, the
oven fan and light do not come on until cooking
begins.
Some internal noise may be heard during
operation. This is quite normal.
TO FIT THE MAIN OVEN SHELVES
The shelves should be fitted with the straight rods
uppermost on the frame and the forms towards the
back of the oven.
To remove a shelf slide the shelf towards you until
the shelf stop is reached. Tilt shelf up at the front so
that the stops clear the side supports. Lift shelf clear.
To install a shelf, reverse the above steps. Each
shelf position has an upper and lower support wire,
ensure the shelf is placed between these two support
wires.
USING THE TELESCOPIC RUNNERS
(where fitted)
1. Ensure the telescopic runners are pushed back
into the oven cavity before fitting the shelf.
2. Holding the front edge of the shelf with both
hands, place the rear shelf forms over the
telescopic runners.
3. Slide the shelf into position, lifting slightly at the
front so that the shelf locates into the retaining
hooks.
To remove, raise the front edge and withdraw the
shelf.
Ensure the shelf is positively located before
using.
Note:
Should you wish to purchase a telescopic runner kit,
this can be ordered from your local Service Force
Centre by quoting part number (BAZ D02).
FORM
RETAINING
HOOK
HINTS AND TIPS
•
•
•
•
•
Arrange the shelves in the required positions
before switching the oven ON. Shelf positions
are counted from the bottom upwards.
When cooking more than one dish in the fan
oven, place dishes centrally on different shelves
rather than cluster several dishes on one shelf,
this will allow the heat to circulate freely for the
best cooking results.
When batch baking one type of food, e.g. Victoria
sandwich cakes, those of similar size will be
cooked in the same time.
It is recommended that when baking larger
quantities the shelf positions should be evenly
spaced to suit the load being cooked. A slight
increase in cooking time may be necessary.
Do not place baking trays directly on the oven
base as it interferes with the oven air circulation
and can lead to base burning; use the lower shelf
position.
Do not place cookware and cooking pots
with rough bases e.g. cast iron on the oven
door as damage to the glass may occur.
20
CONVENTIONAL COOKING
This form of cooking gives you the opportunity to cook without the fan in operation.
It is particularly suitable for dishes which require extra base browning such as pizzas, quiches and flans. Gratins,
lasagnes and hotpots which require extra top browning also cook well in the conventional oven. For best results
cook on one level.
USING CONVENTIONAL COOKING
12.00
•
•
•
Pop out and turn the multifunction selector to
Conventional Cooking.
Wait 5 seconds until your choice is confirmed.
The temperature will automatically set to 200°C.
If you wish to alter the set temperature, you may
do so by pushing out and turning the main oven
increase/decrease selector (+/-) until the required
temperature setting is reached.
THINGS TO NOTE
•
•
•
•
•
•
•
•
If it is necessary to reach the required
temperature in a shorter time, the Speedcook
Function can be used. See Speedcook Function
section.
When the required temperature is reached the
three temperature indicator neons on the timer
display will illuminate and an audible signal will
sound.
The multifunction selector indicator neon and the
main oven increase/decrease selector neon will
glow.
The main oven temperature neons will illuminate
until the oven has reached the desired
temperature and then stop. When the oven has
been switched off the bars that are still lit indicate
the remaining residual heat in the oven.
The cooling fan for the controls may operate after
a time.
The oven light will illuminate.
If an automatic programme has been set, the
oven fan and light do not come on until cooking
begins.
Some internal noise may be heard during
operation. This is quite normal.
21
HINTS AND TIPS
•
•
•
•
•
•
•
•
Single level cooking gives best results. If you
require more than one level of cooking use the
main fan oven.
The middle shelf allows for the best heat
distribution. To increase base browning simply
lower the shelf position. To increase top
browning raise, the shelf position.
There should always be at least 2.5cm (1”)
between the top of the food and the grill element.
This gives best cooking results and allows room
for rise in yeast mixtures, Yorkshire puddings etc.
When cooking cakes, pastry, scones bread etc.,
place the tins or baking trays centrally on the
shelf.
Ensure that food is placed centrally on the shelf
and there is sufficient room around the baking
tray or dish to allow for maximum circulation.
Stand dishes on a suitably sized baking tray on
the shelf to prevent spillage onto the oven base
and to help reduce cleaning.
The material and finish of the baking tray and
dishes used will affect the degree of base
browning. Enamelware, dark, heavy or non-stick
utensils increase base browning. Shiny
aluminium or polished steel trays reflect the heat
away and give less base browning.
Do not place baking trays directly on the oven
base as it interferes with the oven air circulation
and can lead to base burning; use the lower shelf
position.
For economy leave the door open for the shortest
possible time, particularly when placing food into
a pre-heated oven.
Do not place cookware and cooking pots
with rough bases e.g. cast iron on the oven
door as damage to the glass may occur.
22
MAIN OVEN COOKING CHART
The oven temperatures are intended as a guide only. It may be necessary to increase or decrease the
temperatures by 10°C to suit individual preferences and requirements.
VENTITHERM ® PRECISION
FAN COOKING
Food
Biscuits
Bread
Casseroles
Cakes:
Small & Queen
Sponges
Madeira
Rich Fruit
Christmas
Convenience Foods
Fish
Fruit Pies and Crumbles
Milk Puddings
Pastry:
Choux
Shortcrust
Flaky
Puff
Plate Tarts
Quiches/Flans
Scones
CONVENTIONAL
OVEN
APPROX
COOK TIME (m)
Position
Cooking
Temp °C
Shelf
Position
Cooking
Temp °C
Shelf
180 - 190
200 - 220
130 - 160
160 – 170
2
2
2
2
180 - 190
210 - 220
150 - 180
170 - 180
10 - 20
25 - 30
1½ - 2½h
18 - 25
160 - 170
140 - 150
130 - 140
130 - 140
2
2
2
1
170 - 180
160 - 170
150 - 160
130 - 140
20 - 30
1¼ - 1½h
2 - 2½h
3 - 4½h
depends on size
positions
are not
critical
but ensure
that oven
shelves are
evenly
spaced
when more
than one
is used
Follow manufacturer's instructions
170 - 190
2
170 - 190
190 - 200
3
190 - 200
130 -140
3
130 - 140
190 - 200
2
160 - 170
190 - 200
3
190 - 200
210 - 220
3
210 - 220
210 - 220
3
210 - 220
180 - 190
2
190 - 200
170 - 180
2
190 - 200
210 - 220
3
220 - 230
Note: Shelf positions are counted from the bottom of the oven.
23
20 - 30
40 - 60
1½ - 2h
30 - 35
15 - 20
25 - 40
25 - 40
25 - 45
25 - 45
8 - 12
ROASTING CHART
INTERNAL TEMPERATURES –
Rare : 50-60°C; Medium : 60-70°C; Well done : 70-80°C
MEAT
TEMPERATURE
COOKING TIME
20-35 minutes per ½kg (1lb)
and 20-35 minutes over
Beef/ Beef boned
160-180°C
Mutton/Lamb
160-180°C
25-35 minutes per ½kg (1lb)
and 25-35 minutes over
Pork/Veal/Ham
160-180°C
30-40 minutes per ½kg (1lb)
and 30-40 minutes over
Chicken
160-180°C
15-20 minutes per ½kg (1lb)
and 20 minutes over
Turkey/Goose
160-180°C
15-20 minutes per ½kg (1lb)
up to 3½kg (7lb) then 10
minutes per ½kg (1lb) over
3½kg (7lb)
Duck
160-180°C
25-35 minutes per ½kg (1lb)
and 25-30 minutes over
Pheasant
160-180°C
35-40 minutes per ½kg (1lb)
and 35-40 minutes over
Rabbit
160-180°C
20 minutes per ½kg (1lb)
and 20 minutes over
The roasting temperatures and times given in the chart should be adequate for most joints, but slight adjustments
may be required to allow for personal requirements and the shape and texture of the meat. However, lower
temperatures and longer cooking times are recommended for less tender cuts or larger joints.
Wrap joints in foil if preferred, for extra browning uncover for the last 20 – 30 min. cooking time.
24
MAIN OVEN FULL WIDTH GRILL
CAUTION – ACCESSIBLE PARTS MAY BE HOT WHEN THE GRILL IS IN USE. YOUNG CHILDREN
SHOULD BE KEPT AWAY.
USING FULL WIDTH GRILL
12.00
•
•
•
•
Pop out and turn the multifunction selector to Full
Width Grill.
Pop out and turn the multifunction selector for
centre section only.
Wait 5 seconds until your choice is confirmed.
The temperature will automatically set to 250°C.
If you wish to alter the set temperature, you may
do so by pushing out and turning the main oven
increase/decrease selector (+/-) until the required
temperature setting is reached.
THINGS TO NOTE
•
•
•
•
•
•
When the required temperature is reached the
three temperature indicator neons on the timer
display will illuminate and an audible signal will
sound.
The multifunction selector indicator neon and the
main oven increase/decrease selector indicator
neon will glow.
The cooling fan for the controls may operate after
a time.
The oven light will illuminate.
Some internal noise may be heard during
operation. This is quite normal.
The grill may be used with the door open or with
the door closed.
25
•
•
•
•
•
•
•
HINTS AND TIPS
Most foods should be placed on the grid in the
grill pan to allow maximum circulation of air to lift
the food out of the fats and juices.
Adjust the grid and grill pan runner position to
allow for different thicknesses of food. Position
the food close to the element for faster cooking
and further away for more gentle cooking.
Food should be thoroughly dried before grilling to
minimise splashing. Brush lean meats and fish
lightly with a little oil or melted butter to keep
them moist during cooking.
Accompaniments such as tomatoes and
mushrooms may be placed around the outer
edges or underneath the grid when grilling
meats.
When toasting bread, we suggest that the top
runner position is used with the grid in its 'high'
position.
Preheat the grill on full setting for a few minutes
to seal meat or for toasting. Adjust the heat
setting and the shelf position as necessary during
cooking.
The food should be turned over during cooking
as required.
GRILLING CHART
FOOD
Adjust
GRILL TIME
(mins in total)
5-6
shelf
10-15
Chicken Joints
position
30-40
Chops - Lamb
Pork
and
15-20
20-30
Bacon Rashers
Beefburgers
SHELF
grill
Fish - Whole
Trout/Mackerel
pan
15-25
Fillets - Plaice/Cod
grid
10-15
to
20-30
suit
8-12
different
20-30
thicknesses
of
6-12
12-16
14-20
food
3-4
Kebabs
Kidneys - Lamb/Pig
Sausages
Steaks - Rare
Medium
Well Done
Toasted Sandwiches
The times quoted above are given as a guide and
should be adjusted to suit personal taste.
26
PIZZA
This setting can be used for foods such as pizza where base browning and crispness are required.
The top and lower elements operate in conjunction with the oven fan.
USING PIZZA
12.00
•
•
•
HINTS AND TIPS
Pop out and turn the multifunction selector to
Pizza.
•
Wait 5 seconds until your choice is confirmed.
The temperature will automatically set to 150°C.
•
If you wish to alter the set temperature, you may
do so by pushing out and turning the main oven
increase/decrease selector (+/-) until the required
temperature setting is reached.
•
•
THINGS TO NOTE
•
•
•
•
•
•
•
•
If it is necessary to reach the required
temperature in a shorter time, the Speedcook
Function can be used. See Speedcook Function
section.
Single level cooking using the middle shelf
position gives best results.
Ensure that food is place centrally on the shelf for
maximum air circulation.
Be guided by the cook times and temperatures
given on any packaging.
Some pizzas should be cooked directly on the
oven shelf. To prevent soiling the oven base,
place a baking tray in one of the lower shelf
positions.
Do not place dishes, tins or baking trays
directly onto the oven base as it becomes
very hot and damage may occur.
When the required temperature is reached the
three temperature indicator neons on the timer
display will illuminate and an audible signal will
sound.
•
The multifunction selector indicator neon and the
main oven increase/decrease selector indicator
neon will glow.
The main oven temperature neons will illuminate
until the oven has reached the desired
temperature and then stop. When the oven has
been switched off the bars that are still lit indicate
the remaining residual heat in the oven.
The cooling fan for the controls may operate after
a time.
The oven light will illuminate.
If an automatic programme has been set, the
oven fan and light do not come on until cooking
begins.
Some internal noise may be heard during
operation. This is quite normal.
27
The material and finish of the baking trays and
dishes used will affect base browning.
Enamelware, dark heavy or non-stick utensils
increase base browning. Shiny aluminium or
polished steel trays reflect the heat away and
give less base browning.
ROTITHERM ROASTING
Rotitherm Roasting offers an alternative method of cooking food items normally associated with conventional
grilling.
Rotitherm Roasting helps to minimise cooking smells in the kitchen and allows you to grill with the oven door
closed.
With the exception of toast and rare steaks you can Rotitherm Roast all the foods you would normally cook under a
conventional grill.
COOKING TIMES
Cooking is more gentle, therefore food generally takes a little longer to cook when Rotitherm Roasting compared
with conventional grilling. One of the advantages is that larger loads can be cooked at the same time.
The lower part of the oven can be used to cook accompaniments at the same time, e.g. tomatoes and mushrooms
with a mixed grill or breakfast.
Dishes prepared in advance such as shepherd's pie, lasagne and au gratins can be heated through and browned
on the top using the Rotitherm Roasting function.
USING ROTITHERM ROASTING
12.00
•
Always Rotitherm Roast with the oven door
closed and the grill pan handle removed.
•
•
•
•
Pop out and turn the multifunction selector to
Rotitherm Roasting.
Wait 5 seconds until your choice is confirmed.
The temperature will automatically set to 180°C.
•
If you wish to alter the set temperature, you may
do so by pushing out and turning the main oven
increase/decrease selector (+/-) until the required
temperature setting is reached.
•
THINGS TO NOTE
•
•
•
If it is necessary to reach the required
temperature in a shorter time, the Speedcook
Function can be used. See Speedcook Function
section.
•
When the required temperature is reached the
three temperature indicator neons on the timer
display will illuminate and an audible signal will
sound.
•
28
The multifunction selector indicator neon and the
main oven increase/decrease selector indicator
neon will glow.
The main oven temperature neons will illuminate
until the oven has reached the desired
temperature and then stop. When the oven has
been switched off the bars that are still lit indicate
the remaining residual heat in the oven.
The oven fan cycles as part of the cooking
function.
The cooling fan for the controls may operate after
a time.
The oven light will illuminate.
If an automatic programme has been set, the
oven fan and light do not come on until cooking
begins.
Some internal noise may be heard during
operation. This is quite normal.
HINTS AND TIPS
•
•
•
•
•
•
•
Prepare foods in the same way as for
conventional grilling. Brush lean meats and fish
lightly with a little oil or butter to keep them moist
during cooking.
Most food should be placed on the grill pan grid
in the 'high' position in the grill pan to allow
maximum circulation of air around the food.
Accompaniments such as tomatoes and
mushrooms may be placed below the grid when
grilling meats, or in a separate dish on a lower
shelf.
Foods will cook more quickly the closer they are
to the grill element and the higher the
temperatures selected. Be prepared to adjust
temperatures and shelf positions during cooking
if necessary.
Turn food over during cooking as necessary.
ROTITHERM ROASTING CHART
Ensure that ready prepared or cooked chilled
dishes e.g. shepherds pie, moussaka, lasagne,
etc., are piping hot throughout before serving.
FOOD
A temperature range of 140°C - 220° is suitable
for most foods. Be prepared to make suitable
adjustments during cooking to suit individual
requirements. If Rotitherm Roasting on more
than one level, it may be necessary to
interchange the food on the shelves during
cooking.
SHELF
Bacon Rashers
Beefburgers
Chicken Joints
Chops - Lamb/Pork
4
4
4
4
TEMP
(°C)
200
190
160
170
Fish - Whole
Trout/Mackerel
Fillets - Plaice/Cod
Kebabs
Kidneys - Lamb/Pig
Liver
- Lamb/Pig
Sausages
Steaks - Medium
3
3
4
4
4
4
4
170
170
170
180
180
190
220
Steaks - Well Done
4
220
Heating through
and Browning, e.g.
Au -gratin, Lasagne,
Shepherd's Pie.
3
170
TIME (mins
In total)
8-12
10-15
35-45
20-35
10-20
10-15
20-30
10-15
10-15
10-15
8-10
each side
10-15
each side
20-30
depends on
size
NOTE: Shelf positions are counted from the bottom of the
oven.
Times quoted above are given as a guide and should be
adjusted to sit personal taste.
29
SPEEDCOOK
Speedcook is ideal for quick preheating of the oven.
USING SPEEDCOOK
12.00
THINGS TO NOTE
After a cooking function has been selected and the
temperature has been adjusted, the cavity will
gradually heat up until the selected temperature is
reached. This will take from 10 to 15 minutes,
depending on selected function and temperature. If it
is necessary to reach the required temperature in a
shorter time, the Speedcook Function can be used.
The Speedcook Function will overide the selected
main oven function until the required temperature is
reached then return to the selected main oven
function.
The Speedcook function cannot be used with the
Second Oven, Main Oven Full Width Grill or Fan
Controlled Defrosting.
SELECTING SPEEDCOOK
•
•
•
Set the required cooking function and
temperature as explained in the previous pages.
Press the Speedcook control button. The
Speedcook neon will illuminate (
) and the
temperature indicator neons ( °C ) will flash.
When the required temperature is reached the
three temperature indicator neons on the timer
display will illuminate and an audible signal will
sound.
•
The Speedcook neon will go out.
•
The selected cooking function will resume.
30
FAN CONTROLLED DEFROSTING
This main oven function enables you to defrost most foods without heat faster than some conventional methods as
the oven fan circulates air around the food. It is particularly suitable for delicate frozen foods which are to be
served cold e.g. cream filled gateaux, cakes covered with icings or frostings, cheesecakes, biscuits, scones, etc.
12.00
USING FAN CONTROLLED DEFROSTING
•
•
Pop out and turn the multifunction selector to Fan
Controlled Defrosting.
Wait 5 seconds until your choice is confirmed.
The temperature will automatically set to 30°C.
THINGS TO NOTE
•
•
•
•
•
•
•
•
•
•
•
The oven fan and oven light will come on
The cooling fan does not operate.
HINTS AND TIPS
Place the frozen food in a single layer where
possible and turn it over half way through the
defrosting process.
The actual speed of defrosting is influenced by
room temperature. On warm days defrosting will
be faster than on cooler days.
It is preferable to thaw fish, meat and poultry
slowly in the fridge. However, this process can
be accelerated by using the defrost function.
Small or thin fish fillets, frozen peeled prawns,
cubed or minced meat, liver, thin chops, steaks
etc., can be thawed in 1 – 2 hours.
A 1kg/2¼lb oven ready chicken will be thawed in
approximately 5 hours. Remove the giblets as
soon as possible during the thawing process.
Joints of meat up to 2kg/4½lb in weight can be
thawed using the defrost function.
All joints of meat and poultry must be thawed
thoroughly before cooking.
Always cook
thawing.
thoroughly
immediately
after
Do not leave food at room temperature once it is
defrosted. Cook raw food immediately or store
cooked food in the fridge, once it has been
cooled.
Care must always be taken when handling foods
in the home. Always follow the basic rules of
food hygiene to prevent bacterial growth and
cross contamination when defrosting, preparing,
cooking, cooling and freezing foods.
31
CARE AND CLEANING
Before cleaning always allow the appliance to
cool down before switching off at the
electricity supply.
CLEANING MATERIALS
Before using any cleaning materials on your
appliance, check that they are suitable and that their
use is recommended by the manufacturer.
Cleaners that contain bleach should NOT be used as
they may dull the surface finishes. Harsh abrasives
and scourers should also be avoided as damage will
occur.
CLEANING THE
APPLIANCE
OUTSIDE
OF
THE
Do not use abrasive cleaning materials e.g. Hob
Brite, Brillo pads or scourers on painted or printed
finishes as damage may occur.
Regularly wipe over the control panel, doors and
handles using a soft cloth and hot soapy water. To
prevent streaking finish with a soft cloth.
Stainless Steel cream cleaners are abrasive and
should be avoided as they may dull the surface
finish. Any spillage on the stainless steel finish
must be wiped off immediately.
Do not attempt to remove any of the control
knobs from the panel as this may cause
damage and is a safety hazard.
Under no circumstances should the door
assembly be detached from the product for
cleaning.
REMOVING AND REPLACING
WIREWORK RUNNERS
Remove all shelves and furniture from the oven.
Hold the wirework at the bottom, unclip from the
cavity side and gently pull towards the centre of the
oven.
Unhook the runner at the top and remove from the
cavity.
To replace, ensure the side panel is assembled on to
the wirework runner before hooking it back into the
oven.
To replace the runners, hook the wirework side
runner into the cavity, slide back and press into
place.
SIDE PANEL
CAVITY
CENTRE
Ensure the wirework runners are firmly in
position before replacing the oven
shelves.
32
CLEANING INSIDE THE OVENS
The sides and back of the grill/second oven and main
oven compartments are coated with a special
Stayclean coating. They should not be cleaned
manually.
The vitreous enamel main oven base and grill
compartment base can be cleaned using normal
oven cleaners with care. Ensure that the
manufacturers instructions are followed and that all
parts are well rinsed afterwards.
Aerosol cleaners must not come into
contact with elements, the door seal, or any
painted finishes as this may cause damage.
HINTS AND TIPS
Aerosol cleaners must not be used on
Stayclean surfaces.
Stayclean surfaces destroy splashes of food and fats
when the oven temperature is raised to around 220°C.
It is a good idea to run the oven for an hour or two per
week to ensure continued good performance from the
Stayclean finish.
Slight discolouration and polishing of the Stayclean
surfaces may occur in time. This DOES NOT affect
the Stayclean properties in any way.
Use minimal, if any, extra oil or fat when roasting
meat, potatoes only require brushing with fat before
cooking. Extra fat in the oven during roasting will
increase splashing and soilage.
It is NOT necessary to add water to a meat tin when
roasting. The water and the fat juices from the joint
create excessive splattering during cooking – even at
normal
temperatures,
as
well
as
causing
condensation.
Covering joints during cooking will also prevent
splashing onto the interior surfaces. Removing the
covering for the last 20-30 minutes will allow extra
browning if required. Some large joints and turkeys
especially benefit by this method of cooking, allowing
the joint to cook through before the outside is overbrowned.
33
CLEANING THE DOOR(S)
To prevent damaging or weakening the
door glass panels avoid the use of the
following:
• Household detergents and bleaches
• Impregnated pads unsuitable for nonstick saucepans
• Brillo/Ajax pads or steel wool pads
• Chemical oven pads or aerosols
• Rust removers
• Bath/Sink stain removers
Under no circumstances should the door
assembly be detached from the product for
cleaning.
TO REMOVE THE INNER GLASS
1. Fully open the door.
2. Firmly grasp the rear edge of the inner glass panel
with both hands.
3. Push the glass panel towards you until it clears
the hinge location points at the rear.
4. With one hand, carefully lift the glass panel to
disengage it from the location points under the
handle. (With your other hand, hold the outer
door to ensure it does not spring shut on
removing the inner panel).
5. Close the oven door.
If the door glass panel becomes chipped or
has deep scratches the glass will be
weakened and must be replaced to prevent
the possibility of the panel shattering.
Please contact your local Service Force
Centre who will be pleased to advise
further.
TO CLEAN THE INNER GLASS DOOR
PANEL
Clean the inner door glass panel using a soft cloth
and hot water to which a little washing up liquid has
been added. If the inner panel is heavily soiled, Hob
Brite may be used. Do not use abrasive cleaning
materials on the door glass. Ensure that all parts are
well rinsed and thoroughly dried before attempting to
replace the glass.
Do not clean stainless steel outer panels
(where fitted) with Hob Brite as damage to
the finish will occur.
34
TO REPLACE THE INNER GLASS DOOR
PANEL
1. Holding the glass panel in your right hand fully
open the oven door with your left.
2. Gently ease and push the glass into the location
points under the handle before lowering and
sliding the glass into position under the hinge
location points at the rear.
Ensure the glass is properly located and the text 'This
way up' is facing towards you and at the top edge of
the door.
Do not attempt to use the oven without the
glass being in place.
CLEANING THE GRILL AND OVEN
FURNITURE
All removable parts, except the grill pan handle can
be washed in the dishwasher.
The grill pan, grill pan grid, and oven shelves may be
cleaned using a soap impregnated steel wool pad.
Soaking first in hot soapy water will make cleaning
easier.
REPLACING AN OVEN LIGHT BULB
(MAIN OVEN)
Disconnect the appliance from the
electricity supply before replacing the bulb.
The type of bulb required is a 300°C 25 watt small
Edison Screw.
1. Make sure the appliance is cool before replacing
the bulb.
2. Open the door and remove the shelves and
wirework runners.
3. Pull the glass bulb cover towards you and then
pull it off. If necessary, use a screwdriver to
carefully lever off the cover, taking care not to
damage the oven cavity.
4. Unscrew the bulb by turning it to the left.
5. Fit a new bulb and then replace the glass bulb
cover.
6. Refit the wirework runners and replace the oven
shelves.
7. Restore the electricity supply and reset the time of
day.
35
REPLACING AN OVEN LIGHT BULB
(TOP OVEN)
The type of bulb required is a 300°C 25 watt small
Edison Screw.
Disconnect the appliance from the
electricity supply before replacing the bulb.
1. Make sure the appliance is cool before replacing
the bulb.
2. Open the door and remove the shelves and
wirework runners.
3. Remove the glass cover by turning it to the left.
4. Unscrew the bulb by turning it to the left.
5. Fit a new bulb and then replace the glass bulb
cover.
6. Refit the wirework runners and replace the oven
shelves.
7. Restore the electricity supply and reset the time of
day.
36
SOMETHING NOT WORKING
Please carry out the following checks on your appliance before calling a Service Engineer. It may be that the
problem is a simple one which you can solve yourself without the expense of a service call.
In-guarantee customers should make sure that the checks have been made as the engineer will make a
charge if the fault is not a mechanical or electrical breakdown.
Please note that proof of purchase is required for in-guarantee service calls.
PROBLEM
POSSIBLE SOLUTION
The grill, ovens and timer do not work.
Check that the appliance has been wired in to the
appliance supply and is switched on at the wall.
Check that the main appliance fuse is working.
If you have checked the above:
Allow the appliance to cool for a couple of hours. The
appliance should now be working normally.
The grill and second oven work but the main oven
does not.
Check that the time of day has been set on the clock.
Check that the oven is set for manual cooking.
The grill does not work or cuts out after being used
for a long period of time.
Ensure the cooling fan is running when the grill is on. If
the cooling fan fails, the grill will not operate correctly.
Contact your local Service Force Centre.
Leave the grill door open and allow the grill to cool. After
a couple of hours check that the grill works as normal
The timer does not work.
Check that the instructions for the operation of the timer
are being closely followed.
The indicator neons are not working correctly.
Check that you have selected only the function you
require. Ensure all other controls are in the Off position.
The oven is not cooking evenly.
Check that the appliance is correctly installed and is
level.
Check that the recommended temperatures and shelf
positions are being used.
The oven light fails to illuminate.
The oven light bulb may need replacing.
If the Main Oven is set for automatic cooking the light will
illuminate when the cook time begins.
The oven fan is noisy.
Check that the oven is level.
Check that the shelves and bakeware are not vibrating in
contact with the oven back panel.
The oven temperature is too high or too low.
Check that the recommended temperatures and shelf
positions are being used. Be prepared to adjust the
temperature up or down by 10°C to achieve the results
you want.
37
SERVICE AND SPARE PARTS
In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your local
Service Force Centre by telephoning:-
0870 5 929929
Your telephone call will be automatically routed to the Service Force Centre covering your post code area.
For the address of your local Service Force Centre and further information about Service Force, please visit the
website at www.serviceforce.co.uk
Before calling out an engineer, please ensure you have read the details under the heading "Something Not
Working".
When you contact the Service Force Centre you will need to give the following details:
1. Your name, address and post code.
2. Your telephone number.
3. Clear and concise details of the fault.
4. The model and serial number of the appliance (found on the rating plate).
5. The purchase date.
Please note that a valid purchase receipt or guarantee documentation is required for in-guarantee service
calls.
For Customer Service in Ireland please contact us at the address below:
AEG-Electrolux
Electrolux Group (Irl) Ltd
Long Mile Road
Dublin 12
Republic of Ireland
Tel: +353 (0) 1 4090754
Email: service.eid@electrolux.ie
CUSTOMER CARE DEPARTMENT
For general enquires concerning your AEG-Electrolux appliance, or for further information on AEG-Electrolux
products, please contact our Customer Care Department by letter or telephone at the address below or visit our
website at www.aeg-electrolux.co.uk
Customer Care Department
AEG-Electrolux
Major Appliances
Addington Way
Luton
Bedfordshire
LU4 9QQ
Tel: 0870 5 350350 (*)
*calls to this number may be recorded for training purposes.
38
GUARANTEE CONDITIONS
Standard guarantee conditions
AEG-Electrolux offer the following guarantee to the first purchaser of this appliance:
1. The guarantee is valid for 12 months commencing when the appliance is handed over to the first retail
purchaser, which must be verified by purchase invoice or similar documentation.
The guarantee does not cover commercial use.
2. The guarantee covers all parts or components which fail due to faulty workmanship or faulty material. The
guarantee does not cover appliances where defects or poor performance are due to misuse, accidental
damage, neglect, faulty installation, unauthorised modification or attempted repair, commercial use or failure to
observe requirements and recommendations set out in the instruction book
This guarantee does not cover such parts as light bulbs, removable glassware or plastic.
3. Should guarantee repairs be necessary the purchaser must inform the nearest customer service office (AEGElectrolux's service or authorised agent). AEG-Electrolux reserves the right to stipulate the place of repair (i.e.
the customer’s home place of installation or AEG-Electrolux workshop).
4. The guarantee of free replacement includes both labour and materials.
5. Repairs carried out under guarantee do not extend the guarantee period for the appliance. Parts removed
during guarantee repairs become the property of AEG-Electrolux.
6. The Purchaser’s statutory rights are not affected by this guarantee.
European Guarantee
If you should move to another country within Europe then your guarantee moves with you to your new home
subject to the following qualifications:
•
•
The guarantee starts from the date you first purchased your product.
The guarantee is for the same period and to the same extent for labour and parts as exists in the new country
of use for this brand or range of products.
•
This guarantee relates to you and cannot be transferred to another user.
•
Your new home is within the European Community (EC) or European Free Trade Area.
•
•
The product is installed and used in accordance with our instructions and is only used domestically, i.e. a
normal household.
The product is installed taking into account regulations in your new country.
Before you move please contact your nearest Customer Care centre, listed below, to give them details of your new
home. They will then ensure that the local Service Organisation is aware of your move and able to look after you
and your appliances.
France
Germany
Italy
Sweden
UK
Ireland
Senlis
Nürnberg
Pordernone
Stockholm
Luton
Dublin
+33
+49
+39
+46
+44
+353
(0) 3 44 62 29 29
(0) 800 234 7378
(0) 800117511
(0) 8 672 53 60
(0) 8705 350 350
(0) 1 4090754
39
TECHNICAL DETAILS
Voltage:
230-240 Volts AC 50Hz
Wattage:
5.8-6.3kW
Height:
897 mm
Width:
592 mm
Depth:
563 mm
(excluding handles and knobs)
Weight:
59kg
This appliance complies with: European Council Directive 73/23/EEC.
EMC Directive 89/336/EEC.
CE Marking Directive 93/68/EEC. Energy Label Directive 2002/40/EC.
40
INSTALLATION INSTRUCTIONS
WARNINGS
•
•
•
•
•
This appliance must be installed by a
qualified
electrician/competent
person.
Safety may be impaired if installation is not
carried out in accordance with these
instructions.
This appliance must be earthed.
Do not remove the screws from the earth tab
extending from the oven mains terminal
block (Fig. 1).
Before connecting the appliance make sure
that the voltage of your electricity supply is
the same as that indicated on the rating
plate. This is situated on the lower front
frame of the appliance and can be seen upon
opening the door. Alternatively the rating
plate may also be found on the back or top
of some models (where applicable).
Fig.1
Do not alter the electrical circuitry of this
appliance.
THINGS TO NOTE
•
•
•
•
•
•
This appliance is designed to be fitted in cabinets
of the recommended dimensions as shown
(Fig.3).
If your cabinet interior dimension is between 565570mm the oven may still be fitted. However, a
minor modification to the cabinet will be required
to reduce the aperture size down to 560-565 mm,
to allow the product to be securely screwed into
the cabinet.
The dimensions given provide adequate air
circulation around the unit within the cabinet,
ensuring compliance with BS EN60-335.
Enquiries regarding the installation of the cooker
point, if required, should be made to your
Regional Electricity Company to ensure
compliance with their regulations.
The appliance socket switch should be outside
the cabinet but within 2m of the appliance to
make it accessible to switch off the appliance in
case of an emergency.
To protect the hands, wear gloves when lifting
the oven into its housing.
Do not lift the appliance by the handles.
NOTE: HOUSE CIRCUIT
Earth leakage and continuity tests must be carried
out before the appliance is connected to the mains
supply and re-checked after fitting.
41
CHOICE OF ELECTRICAL CONNECTION
•
There are three possible ways to connect your
appliance. In each case the appliance should be
operated using at least 6mm2 twin core and earth
PVC insulated. Please choose from the most
appropriate after reading the different methods:-
a) By connecting the appliance to a cooker point
(having a double pole isolating switch with at
least 3mm contact separation in all poles and
neutral) and protected with a fuse or miniature
circuit breaker at your mains fuse box.
Subject to Regional Electricity Companies
regulations if you wish to connect the oven
and hob to the power supply you may use
one of the following two methods:b) By connecting the appliance together with a hob
directly to a cooker point(s). Having a double
pole isolating switch with at least 3mm contact
separation in all poles and neutral.
c) If you wish to connect an oven and a hob to a
cooker point you can by connecting the oven and
hob separately to the cooker point. Oven and
hob units should be separately connected to a
cooker point. See Fig. 2.
Fig. 2
NOTE: It is good practice to :
•
•
Fit an Earth Leakage Circuit Breaker to your
house wiring.
Wire your appliance to the latest IEE regulations.
PREPARING CABINET FOR FITTING OF
OVEN
•
•
•
•
Make sure that the cabinet is the correct size for
the appliance to be fitted (Ref. Fig. 3).
If the size is between 565-570mm, then the
cabinet should be modified so that at the screw
fixing points the recommended dimension of at
least 560-565mm is maintained. The modification
should ideally be localised to ensure that after
screw fitment the oven is securely fixed into
position.
The cabinet must be stable and level by firmly
securing it to the wall or floor. If necessary,
make arrangements to ensure the shelf upon
which the oven will rest is level.
When the appliance is installed ensure a
minimum gap of 2mm is maintained between the
trim on the bottom edge of the appliance, and
any corresponding door / panel underneath.
42
RECOMMENDED CABINET DIMENSIONS (IN MILLIMETRES)
Cross section
through cabinet
showing oven
positioned
Fig. 3 Built In Installation
43
HOW TO FINISH UNPACKING
•
•
Place packed appliance next to the space in
which it will be installed.
Remove the appliance packing except for bottom
tray which should be left in position until the
appliance is ready to be fitted into its cabinet.
NOTE: It is imperative that the appliance is
left in the base to protect both the appliance
and the floor.
•
Ensure the user is given these operating
instructions.
Important:
Switch off at the mains,
miniature circuit breaker and if appropriate,
remove fuse before commencing any
electrical work.
TO REMOVE COVER OF MAINS TERMINAL
From the rear of the appliance, remove mains input
terminal cover to gain access to terminal block.
•
First remove retaining screw with pozidrive
screwdriver. See Fig. 4.
Fig. 4
•
Prise cover loose using screwdriver in position
(1) then lever off with screwdriver in position (2)
at either side. See Fig. 5.
Fig.5
•
Lift cover and remove screw from cable clamp.
See Fig. 6.
Fig.6
44
CONNECTING TO THE MAINS TERMINAL
Warning: This appliance must be earthed.
•
•
•
•
•
•
•
•
•
We recommend you use a new length of 6mm2
twin core and earthed cable to ensure your
safety.
Make connection as shown in Fig. 7 by
proceeding as follows:Preform wires to the appropriate shape to suit
fitting into the mains terminal block.
Strip
inner
wirestrippers.
insulation
on
wires
using
Twist the bared wires using pliers.
Cut bared wires 10mm away from the end of the
inner insulation. Where uninsulated Earth wires
are used ensure they are suitably sheathed to
leave 10mm bare wire to fit into the terminal.
Fig.7
Clamp bare wires into the relevant terminal and
check they are held by tugging each one in turn.
Clamp the mains cable securely ensuring 5mm of
the outer insulation is inside the terminal block
and that the wires are not taught but not so slack
as to cause any fouling. See Fig. 7.
Place fuse/miniature circuit breaker in circuit and
switch on at mains.
CHECKING ELECTRICAL CONNECTIONS
Correct electrical connection can be confirmed when
switching on the appliance as the timer will be
flashing.
NOTE: HOUSE CIRCUIT
Earth leakage and continuity tests must be carried
out before the appliance is connected to the mains
supply and re-checked after fitting.
CONNECTING TO A HOB OR COOKER
POINT
•
Either follow in general terms the instructions for
connecting to the terminal block or refer to the
hob suppliers installation instructions.
Feed the cable through the cabinet and
arrange to route the cable away from the
appliance which may become hot.
45
FITTING INTO THE CABINET
IMPORTANT: Ensure that the oven is
switched off at the wall before any further
work is carried out.
•
•
•
•
•
Using a tape measure establish the internal width
of the cabinet. Refer to page 40 if greater than
565mm.
Position the appliance in front of the cabinet.
See Fig. 8.
Take out all oven furniture before installation to
reduce the weight you need to lift. The oven door
should be taped up to keep it closed whilst lifting.
Fig. 8
To place the appliance into the cabinetry follow
the procedure below:
N.B. Two people will be required to carry out
the lifting procedure.
Warning:
Do not attempt to lift this
appliance by the handle(s).
a) Each person should squat either side of the
appliance.
b) Tilt the appliance so that your hands can support
the underside of the appliance.
c) Keeping your back straight, raise the appliance to
the correct height by straightening at the knees.
d) Rest the rear underside of the appliance on the
cabinet floor while your hands support the front.
e) The appliance can be pushed fully into the
cabinet. Take care to avoid fouling the mains
lead.
f)
Fixing points for
stability screws
Ensure the appliance is central and level.
g) Do not remove spacers fitted behind fixing holes.
h) When the appliance is fully housed screw the
stability screws (supplied with the appliance) into
the side of the cabinet taking care not to distort
the side trims (See Fig 9). It is advisable to turn
each screw alternatively to avoid damaging the
trims.
i)
Fig. 9
Switch on the appliance then refer to the
operating instructions.
46
NOTES
47
IMPORTANT NOTICE
In line with our continuing policy of research and development, we reserve the right to alter models and
specifications without prior notice.
This instruction booklet is accurate at the date of printing, but will be superseded if specifications or appearance are
changed.
AEG-ELECTROLUX
MAJOR APPLIANCES,
ADDINGTON WAY,
LUTON,
BEDFORDSHIRE
LU4 9QQ.
TELEPHONE 0870 5 350350
To buy accessories, consumables and spare parts at our online shop please visit:
http://www.aeg-electrolux.co.uk
Part Number: 311807800