HP ProLiant ML110 Specifications

HP ProLiant ML110 Generation 5 Server
Maintenance and Service Guide
Part number 446731-004
Fourth Edition April 2009
Legal notices
© Copyright 2009 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice. The only warranties for HP products and services are
set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed
as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
Intel, Pentium, Xeon, Celeron, and Intel Core are trademarks or registered trademarks of Intel Corporation or its subsidiaries
in the United States and other countries.
Contents
Customer self repair ............................................................................................................................... 5
Parts only warranty service........................................................................................................................ 5
Illustrated parts catalog ......................................................................................................................... 16
Mechanical components ......................................................................................................................... 16
System components ................................................................................................................................ 20
HP contact information ........................................................................................................................... 25
Before you contact HP ....................................................................................................................... 25
Removal and replacement procedures .................................................................................................... 26
Required tools ....................................................................................................................................... 26
Server warnings and cautions.................................................................................................................. 26
Symbols on equipment............................................................................................................................ 27
Electrostatic discharge information ........................................................................................................... 28
Pre-installation procedure ........................................................................................................................ 28
Post-installation procedure ....................................................................................................................... 29
Powering down the server ....................................................................................................................... 29
Cable management................................................................................................................................ 30
System covers........................................................................................................................................ 31
Access panel .................................................................................................................................... 31
Front bezel....................................................................................................................................... 32
Drive bay configuration .......................................................................................................................... 33
System drive cable management ......................................................................................................... 34
Removable media drives .................................................................................................................... 35
Hard drives ...................................................................................................................................... 38
System board configuration..................................................................................................................... 42
Processor ......................................................................................................................................... 42
Memory........................................................................................................................................... 47
Expansion board .............................................................................................................................. 49
System battery .................................................................................................................................. 54
System fan ............................................................................................................................................ 56
Power supply unit................................................................................................................................... 58
PSU replacement warnings ................................................................................................................. 58
Diagnostic tools ................................................................................................................................... 60
Troubleshooting resources ....................................................................................................................... 60
HP Insight Diagnostics ............................................................................................................................ 60
Survey Utility ......................................................................................................................................... 60
Array Diagnostic Utility........................................................................................................................... 61
Phoenix BIOS software ........................................................................................................................... 61
Configuring the system BIOS ................................................................................................................... 61
Setup Utility navigation keys ............................................................................................................... 63
Setup Utility menus ............................................................................................................................ 64
Boot-time diagnostic screen ................................................................................................................ 68
Updating the system BIOS .................................................................................................................. 69
Recording custom Setup values ........................................................................................................... 69
Loading system defaults ..................................................................................................................... 70
Clearing CMOS ............................................................................................................................... 70
Power-On-Self-Test ............................................................................................................................. 71
Contents
3
Connectors, switches, and LEDs ............................................................................................................. 75
Connectors and components ................................................................................................................... 75
Front panel....................................................................................................................................... 75
Rear panel ....................................................................................................................................... 76
System board ................................................................................................................................... 77
Status LED indicators .............................................................................................................................. 79
External LED indicators ...................................................................................................................... 79
System board LED indicators .............................................................................................................. 80
System specifications ............................................................................................................................ 81
Hardware specifications ......................................................................................................................... 81
System unit....................................................................................................................................... 81
Memory........................................................................................................................................... 82
Processor ......................................................................................................................................... 82
SATA optical disc drives .................................................................................................................... 87
SAS hard drives................................................................................................................................ 88
SATA hard drives.............................................................................................................................. 89
SAS controller board ......................................................................................................................... 90
Power supply unit.............................................................................................................................. 91
Software specifications ........................................................................................................................... 92
Physical specifications ............................................................................................................................ 93
Environmental specifications .................................................................................................................... 94
Index .................................................................................................................................................. 95
Contents
4
Customer self repair
HP products are designed with many Customer Self Repair (CSR) parts to minimize repair time and
allow for greater flexibility in performing defective parts replacement. If during the diagnosis period
HP (or HP service providers or service partners) identifies that the repair can be accomplished by the
use of a CSR part, HP will ship that part directly to you for replacement. There are two categories of
CSR parts:
•
Mandatory—Parts for which customer self repair is mandatory. If you request HP to replace
these parts, you will be charged for the travel and labor costs of this service.
•
Optional—Parts for which customer self repair is optional. These parts are also designed for
customer self repair. If, however, you require that HP replace them for you, there may or may not
be additional charges, depending on the type of warranty service designated for your product.
NOTE: Some HP parts are not designed for customer self repair. In order to satisfy the customer
warranty, HP requires that an authorized service provider replace the part. These parts are identified
as "No" in the Illustrated Parts Catalog.
Based on availability and where geography permits, CSR parts will be shipped for next business day
delivery. Same day or four-hour delivery may be offered at an additional charge where geography
permits. If assistance is required, you can call the HP Technical Support Center and a technician will
help you over the telephone. HP specifies in the materials shipped with a replacement CSR part
whether a defective part must be returned to HP. In cases where it is required to return the defective
part to HP, you must ship the defective part back to HP within a defined period of time, normally five
(5) business days. The defective part must be returned with the associated documentation in the
provided shipping material. Failure to return the defective part may result in HP billing you for the
replacement. With a customer self repair, HP will pay all shipping and part return costs and
determine the courier/carrier to be used.
For more information about HP's Customer Self Repair program, contact your local service provider.
For the North American program, refer to the HP website (http://www.hp.com/go/selfrepair).
Parts only warranty service
Your HP Limited Warranty may include a parts only warranty service. Under the terms of parts only
warranty service, HP will provide replacement parts free of charge.
For parts only warranty service, CSR part replacement is mandatory. If you request HP to replace
these parts, you will be charged for the travel and labor costs of this service.
Customer self repair
5
Réparation par le client (CSR)
Les produits HP comportent de nombreuses pièces CSR (Customer Self Repair = réparation par le
client) afin de minimiser les délais de réparation et faciliter le remplacement des pièces défectueuses.
Si pendant la période de diagnostic, HP (ou ses partenaires ou mainteneurs agréés) détermine que la
réparation peut être effectuée à l'aide d'une pièce CSR, HP vous l'envoie directement. Il existe deux
catégories de pièces CSR:
•
Obligatoire - Pièces pour lesquelles la réparation par le client est obligatoire. Si vous
demandez à HP de remplacer ces pièces, les coûts de déplacement et main d'œuvre du service
vous seront facturés.
•
Facultatif - Pièces pour lesquelles la réparation par le client est facultative. Ces pièces sont
également conçues pour permettre au client d'effectuer lui-même la réparation. Toutefois, si vous
demandez à HP de remplacer ces pièces, l'intervention peut ou non vous être facturée, selon le
type de garantie applicable à votre produit.
REMARQUE: Certaines pièces HP ne sont pas conçues pour permettre au client d'effectuer lui-même
la réparation. Pour que la garantie puisse s'appliquer, HP exige que le remplacement de la pièce soit
effectué par un Mainteneur Agréé. Ces pièces sont identifiées par la mention "Non" dans le
Catalogue illustré.
Les pièces CSR sont livrées le jour ouvré suivant, dans la limite des stocks disponibles et selon votre
situation géographique. Si votre situation géographique le permet et que vous demandez une
livraison le jour même ou dans les 4 heures, celle-ci vous sera facturée. Pour bénéficier d'une
assistance téléphonique, appelez le Centre d'assistance technique HP. Dans les documents envoyés
avec la pièce de rechange CSR, HP précise s'il est nécessaire de lui retourner la pièce défectueuse. Si
c'est le cas, vous devez le faire dans le délai indiqué, généralement cinq (5) jours ouvrés. La pièce et
sa documentation doivent être retournées dans l'emballage fourni. Si vous ne retournez pas la pièce
défectueuse, HP se réserve le droit de vous facturer les coûts de remplacement. Dans le cas d'une
pièce CSR, HP supporte l'ensemble des frais d'expédition et de retour, et détermine la société de
courses ou le transporteur à utiliser.
Pour plus d'informations sur le programme CSR de HP, contactez votre Mainteneur Agrée local. Pour
plus d'informations sur ce programme en Amérique du Nord, consultez le site Web HP
(http://www.hp.com/go/selfrepair).
Service de garantie "pièces seules"
Votre garantie limitée HP peut inclure un service de garantie "pièces seules". Dans ce cas, les pièces
de rechange fournies par HP ne sont pas facturées.
Dans le cadre de ce service, la réparation des pièces CSR par le client est obligatoire. Si vous
demandez à HP de remplacer ces pièces, les coûts de déplacement et main d'œuvre du service vous
seront facturés.
Customer self repair
6
Riparazione da parte del cliente
Per abbreviare i tempi di riparazione e garantire una maggiore flessibilità nella sostituzione di parti
difettose, i prodotti HP sono realizzati con numerosi componenti che possono essere riparati
direttamente dal cliente (CSR, Customer Self Repair). Se in fase di diagnostica HP (o un centro di
servizi o di assistenza HP) identifica il guasto come riparabile mediante un ricambio CSR, HP lo
spedirà direttamente al cliente per la sostituzione. Vi sono due categorie di parti CSR:
•
Obbligatorie – Parti che devono essere necessariamente riparate dal cliente. Se il cliente ne
affida la riparazione ad HP, deve sostenere le spese di spedizione e di manodopera per il
servizio.
•
Opzionali – Parti la cui riparazione da parte del cliente è facoltativa. Si tratta comunque di
componenti progettati per questo scopo. Se tuttavia il cliente ne richiede la sostituzione ad HP,
potrebbe dover sostenere spese addizionali a seconda del tipo di garanzia previsto per il
prodotto.
NOTA: alcuni componenti HP non sono progettati per la riparazione da parte del cliente. Per
rispettare la garanzia, HP richiede che queste parti siano sostituite da un centro di assistenza
autorizzato. Tali parti sono identificate da un "No" nel Catalogo illustrato dei componenti.
In base alla disponibilità e alla località geografica, le parti CSR vengono spedite con consegna entro
il giorno lavorativo seguente. La consegna nel giorno stesso o entro quattro ore è offerta con un
supplemento di costo solo in alcune zone. In caso di necessità si può richiedere l'assistenza telefonica
di un addetto del centro di supporto tecnico HP. Nel materiale fornito con una parte di ricambio CSR,
HP specifica se il cliente deve restituire dei componenti. Qualora sia richiesta la resa ad HP del
componente difettoso, lo si deve spedire ad HP entro un determinato periodo di tempo, generalmente
cinque (5) giorni lavorativi. Il componente difettoso deve essere restituito con la documentazione
associata nell'imballo di spedizione fornito. La mancata restituzione del componente può comportare
la fatturazione del ricambio da parte di HP. Nel caso di riparazione da parte del cliente, HP sostiene
tutte le spese di spedizione e resa e sceglie il corriere/vettore da utilizzare.
Per ulteriori informazioni sul programma CSR di HP contattare il centro di assistenza di zona. Per il
programma in Nord America fare riferimento al sito Web HP (http://www.hp.com/go/selfrepair).
Servizio di garanzia per i soli componenti
La garanzia limitata HP può includere un servizio di garanzia per i soli componenti. Nei termini di
garanzia del servizio per i soli componenti, HP fornirà gratuitamente le parti di ricambio.
Per il servizio di garanzia per i soli componenti è obbligatoria la formula CSR che prevede la
riparazione da parte del cliente. Se il cliente invece richiede la sostituzione ad HP, dovrà sostenere le
spese di spedizione e di manodopera per il servizio.
Customer self repair
7
Customer Self Repair
HP Produkte enthalten viele CSR-Teile (Customer Self Repair), um Reparaturzeiten zu minimieren und
höhere Flexibilität beim Austausch defekter Bauteile zu ermöglichen. Wenn HP (oder ein HP
Servicepartner) bei der Diagnose feststellt, dass das Produkt mithilfe eines CSR-Teils repariert werden
kann, sendet Ihnen HP dieses Bauteil zum Austausch direkt zu. CSR-Teile werden in zwei Kategorien
unterteilt:
•
Zwingend – Teile, für die das Customer Self Repair-Verfahren zwingend vorgegeben ist.
Wenn Sie den Austausch dieser Teile von HP vornehmen lassen, werden Ihnen die Anfahrt- und
Arbeitskosten für diesen Service berechnet.
•
Optional – Teile, für die das Customer Self Repair-Verfahren optional ist. Diese Teile sind auch
für Customer Self Repair ausgelegt. Wenn Sie jedoch den Austausch dieser Teile von HP
vornehmen lassen möchten, können bei diesem Service je nach den für Ihr Produkt vorgesehenen
Garantiebedingungen zusätzliche Kosten anfallen.
HINWEIS: Einige Teile sind nicht für Customer Self Repair ausgelegt. Um den Garantieanspruch des
Kunden zu erfüllen, muss das Teil von einem HP Servicepartner ersetzt werden. Im illustrierten
Teilekatalog sind diese Teile mit „No“ bzw. „Nein“ gekennzeichnet.
CSR-Teile werden abhängig von der Verfügbarkeit und vom Lieferziel am folgenden Geschäftstag
geliefert. Für bestimmte Standorte ist eine Lieferung am selben Tag oder innerhalb von vier Stunden
gegen einen Aufpreis verfügbar. Wenn Sie Hilfe benötigen, können Sie das HP technische Support
Center anrufen und sich von einem Mitarbeiter per Telefon helfen lassen. Den Materialien, die mit
einem CSR-Ersatzteil geliefert werden, können Sie entnehmen, ob das defekte Teil an HP
zurückgeschickt werden muss. Wenn es erforderlich ist, das defekte Teil an HP zurückzuschicken,
müssen Sie dies innerhalb eines vorgegebenen Zeitraums tun, in der Regel innerhalb von fünf (5)
Geschäftstagen. Das defekte Teil muss mit der zugehörigen Dokumentation in der Verpackung
zurückgeschickt werden, die im Lieferumfang enthalten ist. Wenn Sie das defekte Teil nicht
zurückschicken, kann HP Ihnen das Ersatzteil in Rechnung stellen. Im Falle von Customer Self Repair
kommt HP für alle Kosten für die Lieferung und Rücksendung auf und bestimmt den Kurier/Frachtdienst.
Weitere Informationen über das HP Customer Self Repair Programm erhalten Sie von Ihrem
Servicepartner vor Ort. Informationen über das CSR-Programm in Nordamerika finden Sie auf der HP
Website unter (http://www.hp.com/go/selfrepair).
Parts-only Warranty Service (Garantieservice
ausschließlich für Teile)
Ihre HP Garantie umfasst möglicherweise einen Parts-only Warranty Service (Garantieservice
ausschließlich für Teile). Gemäß den Bestimmungen des Parts-only Warranty Service stellt HP
Ersatzteile kostenlos zur Verfügung.
Für den Parts-only Warranty Service ist das CSR-Verfahren zwingend vorgegeben. Wenn Sie den
Austausch dieser Teile von HP vornehmen lassen, werden Ihnen die Anfahrt- und Arbeitskosten für
diesen Service berechnet.
Customer self repair
8
Reparaciones del propio cliente
Los productos de HP incluyen muchos componentes que el propio usuario puede reemplazar
(Customer Self Repair, CSR) para minimizar el tiempo de reparación y ofrecer una mayor flexibilidad
a la hora de realizar sustituciones de componentes defectuosos. Si, durante la fase de diagnóstico,
HP (o los proveedores o socios de servicio de HP) identifica que una reparación puede llevarse a
cabo mediante el uso de un componente CSR, HP le enviará dicho componente directamente para
que realice su sustitución. Los componentes CSR se clasifican en dos categorías:
•
Obligatorio: componentes para los que la reparación por parte del usuario es obligatoria. Si
solicita a HP que realice la sustitución de estos componentes, tendrá que hacerse cargo de los
gastos de desplazamiento y de mano de obra de dicho servicio.
•
Opcional: componentes para los que la reparación por parte del usuario es opcional. Estos
componentes también están diseñados para que puedan ser reparados por el usuario. Sin
embargo, si precisa que HP realice su sustitución, puede o no conllevar costes adicionales,
dependiendo del tipo de servicio de garantía correspondiente al producto.
NOTA: Algunos componentes no están diseñados para que puedan ser reparados por el usuario.
Para que el usuario haga valer su garantía, HP pone como condición que un proveedor de servicios
autorizado realice la sustitución de estos componentes. Dichos componentes se identifican con la
palabra "No" en el catálogo ilustrado de componentes.
Según la disponibilidad y la situación geográfica, los componentes CSR se enviarán para que
lleguen a su destino al siguiente día laborable. Si la situación geográfica lo permite, se puede
solicitar la entrega en el mismo día o en cuatro horas con un coste adicional. Si precisa asistencia
técnica, puede llamar al Centro de asistencia técnica de HP y recibirá ayuda telefónica por parte de
un técnico. Con el envío de materiales para la sustitución de componentes CSR, HP especificará si los
componentes defectuosos deberán devolverse a HP. En aquellos casos en los que sea necesario
devolver algún componente a HP, deberá hacerlo en el periodo de tiempo especificado,
normalmente cinco días laborables. Los componentes defectuosos deberán devolverse con toda la
documentación relacionada y con el embalaje de envío. Si no enviara el componente defectuoso
requerido, HP podrá cobrarle por el de sustitución. En el caso de todas sustituciones que lleve a cabo
el cliente, HP se hará cargo de todos los gastos de envío y devolución de componentes y escogerá la
empresa de transporte que se utilice para dicho servicio.
Para obtener más información acerca del programa de Reparaciones del propio cliente de HP,
póngase en contacto con su proveedor de servicios local. Si está interesado en el programa para
Norteamérica, visite la página web de HP siguiente (http://www.hp.com/go/selfrepair).
Servicio de garantía exclusivo de componentes
La garantía limitada de HP puede que incluya un servicio de garantía exclusivo de componentes.
Según las condiciones de este servicio exclusivo de componentes, HP le facilitará los componentes de
repuesto sin cargo adicional alguno.
Para este servicio de garantía exclusivo de componentes, es obligatoria la sustitución de
componentes por parte del usuario (CSR). Si solicita a HP que realice la sustitución de estos
componentes, tendrá que hacerse cargo de los gastos de desplazamiento y de mano de obra de
dicho servicio.
Customer self repair
9
Customer Self Repair
Veel onderdelen in HP producten zijn door de klant zelf te repareren, waardoor de reparatieduur tot
een minimum beperkt kan blijven en de flexibiliteit in het vervangen van defecte onderdelen groter is.
Deze onderdelen worden CSR-onderdelen (Customer Self Repair) genoemd. Als HP (of een HP
Service Partner) bij de diagnose vaststelt dat de reparatie kan worden uitgevoerd met een CSRonderdeel, verzendt HP dat onderdeel rechtstreeks naar u, zodat u het defecte onderdeel daarmee
kunt vervangen. Er zijn twee categorieën CSR-onderdelen:
•
Verplicht: Onderdelen waarvoor reparatie door de klant verplicht is. Als u HP verzoekt deze
onderdelen voor u te vervangen, worden u voor deze service reiskosten en arbeidsloon in
rekening gebracht.
•
Optioneel: Onderdelen waarvoor reparatie door de klant optioneel is. Ook deze onderdelen
zijn ontworpen voor reparatie door de klant. Als u echter HP verzoekt deze onderdelen voor u te
vervangen, kunnen daarvoor extra kosten in rekening worden gebracht, afhankelijk van het type
garantieservice voor het product.
OPMERKING: Sommige HP onderdelen zijn niet ontwikkeld voor reparatie door de klant. In
verband met de garantievoorwaarden moet het onderdeel door een geautoriseerde Service Partner
worden vervangen. Deze onderdelen worden in de geïllustreerde onderdelencatalogus aangemerkt
met "Nee".
Afhankelijk van de leverbaarheid en de locatie worden CSR-onderdelen verzonden voor levering op
de eerstvolgende werkdag. Levering op dezelfde dag of binnen vier uur kan tegen meerkosten
worden aangeboden, indien dit mogelijk is gezien de locatie. Indien assistentie gewenst is, belt u een
HP Service Partner om via de telefoon technische ondersteuning te ontvangen. HP vermeldt in de
documentatie bij het vervangende CSR-onderdeel of het defecte onderdeel aan HP moet worden
geretourneerd. Als het defecte onderdeel aan HP moet worden teruggezonden, moet u het defecte
onderdeel binnen een bepaalde periode, gewoonlijk vijf (5) werkdagen, retourneren aan HP. Het
defecte onderdeel moet met de bijbehorende documentatie worden geretourneerd in het
meegeleverde verpakkingsmateriaal. Als u het defecte onderdeel niet terugzendt, kan HP u voor het
vervangende onderdeel kosten in rekening brengen. Bij reparatie door de klant betaalt HP alle
verzendkosten voor het vervangende en geretourneerde onderdeel en kiest HP zelf welke
koerier/transportonderneming hiervoor wordt gebruikt.
Neem contact op met een Service Partner voor meer informatie over het Customer Self Repair
programma van HP. Informatie over Service Partners vindt u op de HP website
(http://www.hp.com/go/selfrepair).
Garantieservice "Parts Only"
Het is mogelijk dat de HP garantie alleen de garantieservice "Parts Only" omvat. Volgens de
bepalingen van de Parts Only garantieservice zal HP kosteloos vervangende onderdelen ter
beschikking stellen.
Voor de Parts Only garantieservice is vervanging door CSR-onderdelen verplicht. Als u HP verzoekt
deze onderdelen voor u te vervangen, worden u voor deze service reiskosten en arbeidsloon in
rekening gebracht.
Customer self repair
10
Reparo feito pelo cliente
Os produtos da HP são projetados com muitas peças para reparo feito pelo cliente (CSR) de modo a
minimizar o tempo de reparo e permitir maior flexibilidade na substituição de peças com defeito. Se,
durante o período de diagnóstico, a HP (ou fornecedores/parceiros de serviço da HP) concluir que o
reparo pode ser efetuado pelo uso de uma peça CSR, a peça de reposição será enviada diretamente
ao cliente. Existem duas categorias de peças CSR:
•
Obrigatória – Peças cujo reparo feito pelo cliente é obrigatório. Se desejar que a HP substitua
essas peças, serão cobradas as despesas de transporte e mão-de-obra do serviço.
•
Opcional – Peças cujo reparo feito pelo cliente é opcional. Essas peças também são
projetadas para o reparo feito pelo cliente. No entanto, se desejar que a HP as substitua, pode
haver ou não a cobrança de taxa adicional, dependendo do tipo de serviço de garantia
destinado ao produto.
OBSERVAÇÃO: Algumas peças da HP não são projetadas para o reparo feito pelo cliente. A fim
de cumprir a garantia do cliente, a HP exige que um técnico autorizado substitua a peça. Essas
peças estão identificadas com a marca "No" (Não), no catálogo de peças ilustrado.
Conforme a disponibilidade e o local geográfico, as peças CSR serão enviadas no primeiro dia útil
após o pedido. Onde as condições geográficas permitirem, a entrega no mesmo dia ou em quatro
horas pode ser feita mediante uma taxa adicional. Se precisar de auxílio, entre em contato com o
Centro de suporte técnico da HP para que um técnico o ajude por telefone. A HP especifica nos
materiais fornecidos com a peça CSR de reposição se a peça com defeito deve ser devolvida à HP.
Nos casos em que isso for necessário, é preciso enviar a peça com defeito à HP dentro do período
determinado, normalmente cinco (5) dias úteis. A peça com defeito deve ser enviada com a
documentação correspondente no material de transporte fornecido. Caso não o faça, a HP poderá
cobrar a reposição. Para as peças de reparo feito pelo cliente, a HP paga todas as despesas de
transporte e de devolução da peça e determina a transportadora/serviço postal a ser utilizado.
Para obter mais informações sobre o programa de reparo feito pelo cliente da HP, entre em contato
com o fornecedor de serviços local. Para o programa norte-americano, visite o site da HP
(http://www.hp.com/go/selfrepair).
Serviço de garantia apenas para peças
A garantia limitada da HP pode incluir um serviço de garantia apenas para peças. Segundo os
termos do serviço de garantia apenas para peças, a HP fornece as peças de reposição sem cobrar
nenhuma taxa.
No caso desse serviço, a substituição de peças CSR é obrigatória. Se desejar que a HP substitua
essas peças, serão cobradas as despesas de transporte e mão-de-obra do serviço.
Customer self repair
11
Customer self repair
12
Customer self repair
13
Customer self repair
14
Customer self repair
15
Illustrated parts catalog
Mechanical components
Illustrated parts catalog
16
Item
Description
Spare part number
Customer self repair
1
2nd removable media drive bay EMI shield
457890-001
Mandatory1
2
Front bezel
457888-001
Mandatory1
3
Hard disk drive (HDD) EMI shield
457889-001
Mandatory1
4
Drive release latch
457893-001
Mandatory1
5
Access panel
457896-001
Mandatory1
6
Full-length card retainer
457893-001
Mandatory1
7
Cable clamp
457893-001
Mandatory1
8
PCI slot cover retainer
457895-001
Mandatory1
9
Lights-Out 100c blank bracket
457894-001
Mandatory1
Mandatory—Parts for which customer self repair is mandatory. If you request HP to replace these
parts, you will be charged for the travel and labor costs of this service.
1
Optional—Parts for which customer self repair is optional. These parts are also designed for
customer self repair. If, however, you require that HP replace them for you, there may or may not be
additional charges, depending on the type of warranty service designated for your product.
2
No—Some HP parts are not designed for customer self repair. In order to satisfy the customer
warranty, HP requires that an authorized service provider replace the part. These parts are identified
as "No" in the Illustrated Parts Catalog.
3
Mandatory: Obligatoire—Pièces pour lesquelles la réparation par le client est obligatoire. Si vous
demandez à HP de remplacer ces pièces, les coûts de déplacement et main d'œuvre du service vous
seront facturés.
1
Optional: Facultatif—Pièces pour lesquelles la réparation par le client est facultative. Ces pièces sont
également conçues pour permettre au client d'effectuer lui-même la réparation. Toutefois, si vous
demandez à HP de remplacer ces pièces, l'intervention peut ou non vous être facturée, selon le type
de garantie applicable à votre produit.
2
No: Non—Certaines pièces HP ne sont pas conçues pour permettre au client d'effectuer lui-même la
réparation. Pour que la garantie puisse s'appliquer, HP exige que le remplacement de la pièce soit
effectué par un Mainteneur Agréé. Ces pièces sont identifiées par la mention “Non” dans le
Catalogue illustré.
3
Illustrated parts catalog
17
Mandatory: Obbligatorie—Parti che devono essere necessariamente riparate dal cliente. Se il cliente
ne affida la riparazione ad HP, deve sostenere le spese di spedizione e di manodopera per il
servizio.
1
Optional: Opzionali—Parti la cui riparazione da parte del cliente è facoltativa. Si tratta comunque
di componenti progettati per questo scopo. Se tuttavia il cliente ne richiede la sostituzione ad HP,
potrebbe dover sostenere spese addizionali a seconda del tipo di garanzia previsto per il prodotto.
2
No: Non CSR—Alcuni componenti HP non sono progettati per la riparazione da parte del cliente.
Per rispettare la garanzia, HP richiede che queste parti siano sostituite da un centro di assistenza
autorizzato. Tali parti sono identificate da un “No” nel Catalogo illustrato dei componenti.
3
Mandatory: Zwingend—Teile, die im Rahmen des Customer Self Repair Programms ersetzt werden
müssen. Wenn Sie diese Teile von HP ersetzen lassen, werden Ihnen die Versand- und Arbeitskosten
für diesen Service berechnet.
1
Optional: Optional—Teile, für die das Customer Self Repair-Verfahren optional ist. Diese Teile sind
auch für Customer Self Repair ausgelegt. Wenn Sie jedoch den Austausch dieser Teile von HP
vornehmen lassen möchten, können bei diesem Service je nach den für Ihr Produkt vorgesehenen
Garantiebedingungen zusätzliche Kosten anfallen.
2
No: Kein—Einige Teile sind nicht für Customer Self Repair ausgelegt. Um den Garantieanspruch des
Kunden zu erfüllen, muss das Teil von einem HP Servicepartner ersetzt werden. Im illustrierten
Teilekatalog sind diese Teile mit „No“ bzw. „Nein“ gekennzeichnet.
3
Mandatory: Obligatorio—componentes para los que la reparación por parte del usuario es
obligatoria. Si solicita a HP que realice la sustitución de estos componentes, tendrá que hacerse
cargo de los gastos de desplazamiento y de mano de obra de dicho servicio.
1
Optional: Opcional— componentes para los que la reparación por parte del usuario es opcional.
Estos componentes también están diseñados para que puedan ser reparados por el usuario. Sin
embargo, si precisa que HP realice su sustitución, puede o no conllevar costes adicionales,
dependiendo del tipo de servicio de garantía correspondiente al producto.
2
No: No—Algunos componentes no están diseñados para que puedan ser reparados por el usuario.
Para que el usuario haga valer su garantía, HP pone como condición que un proveedor de servicios
autorizado realice la sustitución de estos componentes. Dichos componentes se identifican con la
palabra “No” en el catálogo ilustrado de componentes.
3
Mandatory: Verplicht—Onderdelen waarvoor Customer Self Repair verplicht is. Als u HP verzoekt
deze onderdelen te vervangen, komen de reiskosten en het arbeidsloon voor uw rekening.
1
Optional: Optioneel—Onderdelen waarvoor reparatie door de klant optioneel is. Ook deze
onderdelen zijn ontworpen voor reparatie door de klant. Als u echter HP verzoekt deze onderdelen
voor u te vervangen, kunnen daarvoor extra kosten in rekening worden gebracht, afhankelijk van het
type garantieservice voor het product.
2
No: Nee—Sommige HP onderdelen zijn niet ontwikkeld voor reparatie door de klant. In verband
met de garantievoorwaarden moet het onderdeel door een geautoriseerde Service Partner worden
vervangen. Deze onderdelen worden in de geïllustreerde onderdelencatalogus aangemerkt met
"Nee".
3
Illustrated parts catalog
18
Mandatory: Obrigatória—Peças cujo reparo feito pelo cliente é obrigatório. Se desejar que a HP
substitua essas peças, serão cobradas as despesas de transporte e mão-de-obra do serviço.
1
Optional: Opcional—Peças cujo reparo feito pelo cliente é opcional. Essas peças também são
projetadas para o reparo feito pelo cliente. No entanto, se desejar que a HP as substitua, pode
haver ou não a cobrança de taxa adicional, dependendo do tipo de serviço de garantia destinado
ao produto.
2
No: Nenhuma—Algumas peças da HP não são projetadas para o reparo feito pelo cliente. A fim de
cumprir a garantia do cliente, a HP exige que um técnico autorizado substitua a peça. Essas peças
estão identificadas com a marca “No” (Não), no catálogo de peças ilustrado.
3
Illustrated parts catalog
19
System components
Illustrated parts catalog
20
Item
Description
Spare part number
Customer self
repair
1
SATA cable
452334-001
Mandatory1
2
SAS LED cable
444692-001
Mandatory1
3
SAS HDD cable
457892-001
Mandatory1
Mass storage devices
4
Removable media drive
Mandatory1
a) SATA DVD-ROM drive
460697-001
b) SATA DVD-RW drive
460698-001
5
160-GB non-hot-plug SATA hard drive
399968-001
Mandatory1
6
72-GB non-hot-plug SAS hard drive
432151-001
Mandatory1
7
Heat sink fan
457886-001
Optional2
8
Processor (include alcohol pad and thermal
compound)
Optional2
Intel Pentium Dual-Core Processor
a) E2160 (1.80 GHz, 800 MHz FSB, 1 MB L2)
455623-001
b) E5200 (2.5 GHz, 800 MHz FSB, 2MB L2)
503382-001
c) E7400 (2.8 GHz, 1066 MHZ FSB, 3 MB L2 )
508255-001
Dual-Core Intel Xeon Processor
a) 3065 (2.33 GHz, 1333 MHz FSB, 4 MB L2)
454525-001
b) 3075 (2.66 GHz, 1333 MHz FSB, 4 MB L2)
454526-001
c) 3085 (3.0 GHz, 1333 MHz FSB, 4 MB L2)
454527-001
d) E3110 (3.0 GHz, 1333 MHz FSB, 6MB L2)
463509-001
e) E3120 (3.16 GHz, 1333 MHz FSB, 4 MB L2)
493930-001
Quad-Core Intel Xeon Processor
a) X3210 (2.13 GHz, 1066 MHz FSB, 8 MB L2)
457020-001
b) X3220 (2.4 GHz, 1066 MHz FSB, 8 MB L2)
454529-001
c) X3320 (2.5 GHz, 1333 MHz FSB, 6 MB L2)
463508-001
d) X3350 (2.66 GHz, 1333 MHz FSB, 12 MB L2) 463507-001
e) X3330 (2.66 GHz, 1333 MHz FSB, 8 MB L2)
493929-001
f) X3360 (2.4 GHz, 1066 MHz FSB, 8 MB L2)
469858-001
g) X3370 (3.0 GHz, 1333MHz FSB, 12MB L2)
493928-001
Intel Core 2 Duo Processor
E4400 (2.0 GHz, 800 MHz FSB, 2 MB L2)
454528-001
Intel Celeron Processor 400 Sequence
Illustrated parts catalog
21
Item
9
Description
Spare part number
a) L420 (1.6 GHz, 800 MHz FSB, 512 KB L2)
454523-001
b) L440 (2.0 GHz, 800 MHz FSB, 512 KB L2)
454524-001
Customer self
repair
Mandatory1
Memory module (PC2-6400, DDR2-800)
a) 512 MB
459931-001
b) 1GB
459932-001
c) 2 GB
460424-001
10
System board
457883-001
Optional2
11
Lights-Out 100c remote management card
457885-001
Mandatory1
12
SAS controller board
447430-001
Mandatory1
13
System fan (includes rubber clip)
457887-001
Mandatory1
14
365-W power supply unit with cable assembly
457884-001
Mandatory1
15
Miscellaneous cable assemblies
Mandatory1
NOTE: The following cable assemblies are not
included in the exploded figure.
a) Front panel board cable assembly
457897-001
b) Front USB port cable assembly
457898-001
c) SATA power Y-cable
457899-001
Mandatory—Parts for which customer self repair is mandatory. If you request HP to replace these
parts, you will be charged for the travel and labor costs of this service.
1
Optional—Parts for which customer self repair is optional. These parts are also designed for
customer self repair. If, however, you require that HP replace them for you, there may or may not be
additional charges, depending on the type of warranty service designated for your product.
2
No—Some HP parts are not designed for customer self repair. In order to satisfy the customer
warranty, HP requires that an authorized service provider replace the part. These parts are identified
as "No" in the Illustrated Parts Catalog.
3
Mandatory: Obligatoire—Pièces pour lesquelles la réparation par le client est obligatoire. Si vous
demandez à HP de remplacer ces pièces, les coûts de déplacement et main d'œuvre du service vous
seront facturés.
1
Optional: Facultatif—Pièces pour lesquelles la réparation par le client est facultative. Ces pièces sont
également conçues pour permettre au client d'effectuer lui-même la réparation. Toutefois, si vous
demandez à HP de remplacer ces pièces, l'intervention peut ou non vous être facturée, selon le type
de garantie applicable à votre produit.
2
No: Non—Certaines pièces HP ne sont pas conçues pour permettre au client d'effectuer lui-même la
réparation. Pour que la garantie puisse s'appliquer, HP exige que le remplacement de la pièce soit
effectué par un Mainteneur Agréé. Ces pièces sont identifiées par la mention “Non” dans le
Catalogue illustré.
3
Illustrated parts catalog
22
Mandatory: Obbligatorie—Parti che devono essere necessariamente riparate dal cliente. Se il cliente
ne affida la riparazione ad HP, deve sostenere le spese di spedizione e di manodopera per il
servizio.
1
Optional: Opzionali—Parti la cui riparazione da parte del cliente è facoltativa. Si tratta comunque
di componenti progettati per questo scopo. Se tuttavia il cliente ne richiede la sostituzione ad HP,
potrebbe dover sostenere spese addizionali a seconda del tipo di garanzia previsto per il prodotto.
2
No: Non CSR—Alcuni componenti HP non sono progettati per la riparazione da parte del cliente.
Per rispettare la garanzia, HP richiede che queste parti siano sostituite da un centro di assistenza
autorizzato. Tali parti sono identificate da un “No” nel Catalogo illustrato dei componenti.
3
Mandatory: Zwingend—Teile, die im Rahmen des Customer Self Repair Programms ersetzt werden
müssen. Wenn Sie diese Teile von HP ersetzen lassen, werden Ihnen die Versand- und Arbeitskosten
für diesen Service berechnet.
1
Optional: Optional—Teile, für die das Customer Self Repair-Verfahren optional ist. Diese Teile sind
auch für Customer Self Repair ausgelegt. Wenn Sie jedoch den Austausch dieser Teile von HP
vornehmen lassen möchten, können bei diesem Service je nach den für Ihr Produkt vorgesehenen
Garantiebedingungen zusätzliche Kosten anfallen.
2
No: Kein—Einige Teile sind nicht für Customer Self Repair ausgelegt. Um den Garantieanspruch des
Kunden zu erfüllen, muss das Teil von einem HP Servicepartner ersetzt werden. Im illustrierten
Teilekatalog sind diese Teile mit „No“ bzw. „Nein“ gekennzeichnet.
3
Mandatory: Obligatorio—componentes para los que la reparación por parte del usuario es
obligatoria. Si solicita a HP que realice la sustitución de estos componentes, tendrá que hacerse
cargo de los gastos de desplazamiento y de mano de obra de dicho servicio.
1
Optional: Opcional— componentes para los que la reparación por parte del usuario es opcional.
Estos componentes también están diseñados para que puedan ser reparados por el usuario. Sin
embargo, si precisa que HP realice su sustitución, puede o no conllevar costes adicionales,
dependiendo del tipo de servicio de garantía correspondiente al producto.
2
No: No—Algunos componentes no están diseñados para que puedan ser reparados por el usuario.
Para que el usuario haga valer su garantía, HP pone como condición que un proveedor de servicios
autorizado realice la sustitución de estos componentes. Dichos componentes se identifican con la
palabra “No” en el catálogo ilustrado de componentes.
3
Mandatory: Verplicht—Onderdelen waarvoor Customer Self Repair verplicht is. Als u HP verzoekt
deze onderdelen te vervangen, komen de reiskosten en het arbeidsloon voor uw rekening.
1
Optional: Optioneel—Onderdelen waarvoor reparatie door de klant optioneel is. Ook deze
onderdelen zijn ontworpen voor reparatie door de klant. Als u echter HP verzoekt deze onderdelen
voor u te vervangen, kunnen daarvoor extra kosten in rekening worden gebracht, afhankelijk van het
type garantieservice voor het product.
2
No: Nee—Sommige HP onderdelen zijn niet ontwikkeld voor reparatie door de klant. In verband
met de garantievoorwaarden moet het onderdeel door een geautoriseerde Service Partner worden
vervangen. Deze onderdelen worden in de geïllustreerde onderdelencatalogus aangemerkt met
"Nee".
3
Illustrated parts catalog
23
Mandatory: Obrigatória—Peças cujo reparo feito pelo cliente é obrigatório. Se desejar que a HP
substitua essas peças, serão cobradas as despesas de transporte e mão-de-obra do serviço.
1
Optional: Opcional—Peças cujo reparo feito pelo cliente é opcional. Essas peças também são
projetadas para o reparo feito pelo cliente. No entanto, se desejar que a HP as substitua, pode
haver ou não a cobrança de taxa adicional, dependendo do tipo de serviço de garantia destinado
ao produto.
2
No: Nenhuma—Algumas peças da HP não são projetadas para o reparo feito pelo cliente. A fim de
cumprir a garantia do cliente, a HP exige que um técnico autorizado substitua a peça. Essas peças
estão identificadas com a marca “No” (Não), no catálogo de peças ilustrado.
3
Illustrated parts catalog
24
HP contact information
For the name of the nearest HP authorized reseller:
•
•
•
In the United States, call 1-800-345-1518.
In Canada, call 1-800-263-5868.
In other locations, refer to the HP website at www.hp.com.
For HP technical support:
•
In North America:
○ Call 1-800-HP-INVENT (1-800-474-6836). This service is available 24 hours a day, 7 days
a week. For continuous quality improvement, calls may be recorded or monitored.
○ If you have purchased a Care Pack (service upgrade), call 1-800-633-3600. For more
information about Care Packs, refer to the HP website at www.hp.com.
•
Outside North America, call the nearest HP Technical Support Phone Center. For telephone
numbers of worldwide Technical Support Centers, refer to the HP website at www.hp.com.
Before you contact HP
Be sure to have the following information available before you call HP:
•
•
•
•
•
•
•
Technical support registration number (if applicable)
Product serial number
Product model name and number
Applicable error messages
Add-on boards or hardware
Third-party hardware or software
Operating system type and revision level
Illustrated parts catalog
25
Removal and replacement procedures
Required tools
In performing any hardware configuration procedure you may need the following tools:
•
•
T-15 Torx screwdriver
Flat-blade screwdriver
The following references and software tools may also be used:
•
•
•
HP ProLiant ML110 Generation 5 Server Support CD
IPMI Event Log
Diagnostics software
Server warnings and cautions
Before installing a server, be sure that you understand the following warnings and cautions.
WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the internal
system components to cool before touching them.
CAUTION: The server must always be operated with the system covers on. Proper cooling is not
achieved when the system covers are removed.
CAUTION: Whenever installing hardware or performing maintenance procedures requiring access
to internal components, it is recommended that users first back up all server data to avoid loss.
IMPORTANT: Before removing any serviceable parts, determine whether the part is hot-plug or nonhot-plug. If the device is non-hot-plug, you must power down the server. Non-hot-plug devices in the
server include the processor, all boards, memory modules, fans, expansion boards, and all system
drives.
IMPORTANT: Review the specifications of a new component before installing it to make sure it is
compatible with the server. When you integrate new components into the system, record its model
and serial number, and any other pertinent information for future reference. After completing any
removal or replacement procedure, run the diagnostics program to verify that all components
operate properly.
Removal and replacement procedures
26
Symbols on equipment
The following symbols may be placed on equipment to indicate the presence of potentially hazardous
conditions.
This symbol indicates the presence of hazardous energy circuits or electric shock
hazards. Refer all servicing to qualified personnel.
WARNING: To reduce the risk of injury from electric shock hazards, do not open this
enclosure. Refer all maintenance, upgrades, and servicing to qualified personnel.
This symbol indicates the presence of electric shock hazards. The area contains no
user or field serviceable parts. Do not open for any reason.
WARNING: To reduce the risk of injury from electric shock hazards, do not open this
enclosure.
This symbol on an RJ-45 receptacle indicates a network interface connection.
WARNING: To reduce the risk of electric shock, fire, or damage to the equipment, do
not plug telephone or telecommunications connectors into this receptacle.
This symbol indicates the presence of a hot surface or a hot component. If this surface
is touched, the potential for injury exists.
WARNING: To reduce the risk of injury from a hot component, allow the surface to
cool before touching.
weight1_kg
weight1_lb
This symbol indicates that the component exceeds the recommended weight for one
individual to handle safely.
WARNING: To reduce the risk of personal injury or damage to the equipment,
observe local occupational health and safety requirements and guidelines for manual
material handling.
These symbols, on power supplies or systems, indicate that the equipment is supplied
by multiple sources of power.
WARNING: To reduce the risk of injury from electric shock, remove all power cords
to completely disconnect power from the system.
Removal and replacement procedures
27
Electrostatic discharge information
An electrostatic discharge (ESD) can damage static-sensitive devices or microcircuitry. Proper
packaging and grounding techniques are necessary precautions to prevent damage. To prevent
electrostatic damage, observe the following precautions:
•
•
•
Transport products in static-safe containers such as conductive tubes, bags, or boxes.
•
Keep work area free of nonconductive materials, such as ordinary plastic assembly aids and
foam packing.
•
Make sure that you are always properly grounded (earthed) when touching a static-sensitive
component or assembly.
•
•
•
Avoid touching pins, leads, or circuitry.
Keep electrostatic-sensitive parts in their containers until they arrive at static-free stations.
Cover workstations with approved static-dissipating material. Use a wrist strap connected to the
work surface, and properly grounded (earthed) tools and equipment.
Always place drives with the Printed Circuit Board (PCB) assembly-side down.
Use conductive field service tools.
Pre-installation procedure
Perform the steps below before you open the server or before you remove or replace any component.
1.
Perform data backup.
2.
Turn off the server and all the peripherals connected to it.
3.
Unplug all cables from the power outlets to avoid exposure to high energy levels that may cause
burns when parts are short circuited by metal objects such as tools or jewelry.
If necessary, label each cable to expedite reassembly.
4.
Disconnect all telecommunication cables to avoid exposure to shock hazard from ringing
voltages.
5.
Open the server according to the instructions described in the “System covers” section later in
this chapter.
6.
Follow the ESD precautions listed previously in this chapter when handling any hardware
component.
IMPORTANT: To streamline the configuration process, read through the entire installation/removal
procedure first and make sure you understand it before you begin.
Removal and replacement procedures
28
Post-installation procedure
Perform the steps below after installing or removing a server component.
7.
Be sure all components are installed according to the described step-by-step instructions.
8.
Check to make sure you have not left loose tools or parts inside the server.
9.
Reinstall any expansion board, peripheral, and system cables that have previously been
removed.
CAUTION: Do not operate the server for more than ten minutes with the access panel and disk
drives removed. Otherwise, improper cooling airflow may damage the system components.
10.
Reinstall the system covers.
11.
Connect all external cables and the AC power cord to the system.
12.
Press the power button
on the front panel to turn on the server.
Powering down the server
The server does not completely power down when the power button
is pressed. The button toggles
between On and Standby. The standby position removes power from most electronics and the drives,
but some internal circuitry remains active. To completely remove all power from the system, disconnect
all power cords from the server.
WARNING: Hazardous voltages are present inside the server. Always disconnect AC power from
the server and other associated assemblies while working inside the unit. Serious injury may result if
this warning is not observed.
WARNING: To reduce the risk of electric shock or damage to the equipment:
• Do not disable the power cord grounding plug. The grounding plug is an important safety feature.
• Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all times.
• Unplug the power cord from the power supply to disconnect power to the equipment.
• Do not route the power cord where it can be walked on or pinched by items placed against it. Pay
particular attention to the plug, electrical outlet, and the point where the cord extends from the server.
CAUTION: Protect the server from power fluctuations and temporary interruptions with a regulating
uninterruptible power supply (UPS). This device protects the hardware from damage caused by
power surges and voltage spikes, and keeps the system in operation during a power failure.
1.
Shut down the server as directed by the operating system documentation.
2.
Press the power button
to toggle to Standby.
This places the server in standby mode changing the power LED indicator to amber. In this
mode, the main power supply output is disabled. Standby does not completely disable or
remove power from the system.
3.
Disconnect the AC power cord from the AC outlet and then from the server.
4.
Check that the power LED indicator is turned off and that the fan noise has stopped.
5.
Disconnect all external peripheral devices from the server.
Removal and replacement procedures
29
Cable management
Always follow good cable management practices when working inside the computer.
•
•
Keep cables away from major heat sources like the heat sink fan.
•
•
Keep cables clear of sliding or moveable parts to prevent cutting or crimping.
•
•
•
•
•
Some flat ribbon cables come prefolded. Never change the folds on these cables.
Do not jam cables on top of expansion cards or memory modules. Printed circuit cards are not
designed to withstand excessive pressure.
When folding a flat ribbon cable, never fold to a sharp crease. Sharp creases may damage the
wires.
Do not sharply bend any cable. A sharp bend can break the internal wires.
Never bend a SATA data cable tighter than a 30 mm (1.18 in.) radius.
Never crease a SATA data cable.
Do not rely on components like the drive cage, power supply, or system cover to push cables
down into the chassis.
To disconnect a power supply cable from the system board:
CAUTION: Always pull the connector. NEVER pull on the cable. Pulling on the cable can damage
the cable and result in a failed power supply.
1.
Squeeze on the top of the retaining latch attached to the cable end of the connector.
2.
Grasp the cable end of the connector and pull it straight up.
Removal and replacement procedures
30
System covers
The access panel and the front bezel are both detachable. You must remove these system covers
before you can remove or replace a server component.
Access panel
The access panel must be removed to access the internal components and the non-hot-plug mass
storage devices.
To remove the access panel:
1.
Loosen the captive thumbscrew located on the rear edge of the access panel.
2.
Slide the panel back about 2.5 cm (1.0 in) to release it from the chassis notch.
3.
Detach the panel from the chassis.
4.
Place the access panel in a safe place for reinstallation later.
Removal and replacement procedures
31
Front bezel
The front bezel must be removed to access the hard drives and the removable media devices.
To remove the front bezel:
1.
Remove the access panel.
2.
Remove the front bezel.
a. Press the three release tabs (marked by white arrows) located on the inner left edge of the
bezel (1).
b. Rotate the bezel out slightly, and then pull it away from the front panel (2).
3.
Place the front bezel in a safe place for reinstallation later.
Removal and replacement procedures
32
Drive bay configuration
The server supports a maximum of six internal drives. The two upper drive bays are primarily for
removable media drives, while the four lower drive bays are only for hard drives.
Item
Description
1
1st removable media drive
2
2nd removable media drive
3
4th SAS/SATA hard drive
4
3rd SAS/SATA hard drive
5
2nd SAS/SATA hard drive
6
1st SAS/SATA hard drive
7
Removable media drive spare screws
8
HDD spare screws
Removal and replacement procedures
33
System drive cable management
The figures in this section illustrate the system drives' data and power cable connections. Observe the
proper cable management guidelines described on page 30 when routing the cables.
Data cable management
Item
Description
1
SATA cables
2
SAS HDD cable
3
SAS LED cable
Removal and replacement procedures
34
Power cable management
Item
PSU cable label
Connects to
1
P5
1st removable media drive
2
P4
2nd removable media drive
3
P6 from Y cable
4th hard drive
4
P6 from Y cable
3rd hard drive
5
P10
2nd hard drive
6
P9
1st hard drive
7
P1
24-pin power connector (ATXPWRCN1)
8
P3
4-pin power connector (PWRCN1)
Removable media drives
The two upper bays are half height bays that can accommodate a variety of removable media drives
including:
•
•
CD, DVD, CD-RW/DVD combo, DVD-RW drives
DAT 24i, 40i, 72i, Disk to Disk Backup Autoloaders (Internal/External) DAT 40x6, 72x6 drives
To install a removable media drive:
1.
Perform the pre-installation procedure.
2.
If you intend to replace an old media drive, proceed to step 3.
If you intend to install a new media drive in the empty 2nd removable media drive bay, proceed
to step 4.
Removal and replacement procedures
35
3.
Remove the media drive you intend to replace.
a. Disconnect the power and data cables from the back of the installed drive (1).
b. Pull and hold the release tab on the drive latch for the device you want to remove (2).
c.
Slide the device out of the drive bay (3).
d. Remove four screws from the sides of the drive.
Reuse these screws when you install the new removable media drive.
e. Place the old media drive on a static-dissipating work surface or inside an anti-static bag.
f.
Proceed to step 5.
Removal and replacement procedures
36
CAUTION: Do not discard the EMI shield. If the drive is removed in the future, you must reinstall
the shield to maintain proper cooling.
4.
Pull the EMI shield from the 2nd removable media drive bay.
Store it for reassembly later.
5.
Remove the new media drive from its protective packaging.
6.
If you are replacing an old media drive, insert the four screws you removed in step 3-d into the
top screw holes on the sides of the new media drive.
If you are installing an additional media drive, remove four spare removable media drive screws
from the front chassis, and then insert them into the top screw holes on the sides of the new
media drive.
7.
Install the new media drive.
a. Slide the new media drive into the selected bay until it clicks into place (1).
b. Connect the data and power cables to the back of the media drive (2).
8.
Perform the post-installation procedure.
Removal and replacement procedures
37
Hard drives
The four lower drive bays can accommodate 3.5-inch non-hot-plug SAS or SATA hard drives. The
following drive capacities are supported.
•
•
Non-hot-plug SAS HDD – 36-, 72-, 146-, and 300-GB
Non-hot-plug SATA HDD – 80-, 160-, 250-, 500-, and 750-GB
IMPORTANT: SAS hard drives require that you also install a SAS controller board. This board
should be installed in the PCI3 slot. For more information about installing a SAS controller board,
go to page 49.
To install a hard drive:
1.
Perform the pre-installation procedure.
2.
Remove the HDD EMI shield.
a. Remove the HDD EMI shield screw (1).
b. Slide the shield slightly upward to release the shield tabs, and then pull it away from the
chassis (2).
3.
If you intend to replace an old hard drive, proceed to step 4.
If you intend to install an additional hard drive, proceed to step 5.
Removal and replacement procedures
38
4.
Remove the hard drive you intend to replace.
a. Disconnect the power and data cables from the back of the installed drive (1).
b. Pull and hold the corresponding drive release tab (2).
c.
Slide the hard drive from the drive bay (3).
d. Remove four screws from the sides of the drive.
Reuse these screws when you install the new hard drive.
e. Place the old hard drive on a static-dissipating work surface or inside an anti-static bag.
5.
Remove the new hard drive from its protective packaging.
6.
If you are replacing an old hard drive, insert the four screws you removed in step 4-d into the
new drive.
If you are installing an additional hard drive, remove four spare HDD screws from the front
chassis, and then insert them into the new drive.
Proceed to step 7 for SATA drive installation instructions, or to step 8 for a SAS model.
Removal and replacement procedures
39
7.
Install the new SATA hard drive.
a. Slide the new hard drive into the selected bay until it clicks into place (1).
b. Connect the SATA and power cables to the back of the hard drive (2).
c.
8.
Connect the SATA cable to the corresponding SATA connector on the system board (3).
Install the new SAS hard drive.
a. Slide the new hard drive into the selected bay until it clicks into place (1).
b. Connect the SAS HDD data cable to the back of the hard drive (2).
c.
Connect the drive power cable to the back of the SAS HDD cable (3).
d. Connect the SAS HDD cable master connector to the SAS controller board (4).
e. Make sure the SAS LED cable is connected from the SAS controller board to the CN11
connector on the system board.
Go to page 34 for a view of the SAS HDD cable management diagram.
Removal and replacement procedures
40
9.
Reinstall the HDD EMI shield.
a. Slide the bottom side of the shield into its chassis notch (1).
b. Press the top part of the shield to the chassis to secure it in place (2).
c.
10.
Lock the shield with the screw you removed in step 2-a (3).
Perform the post-installation procedure.
Removal and replacement procedures
41
System board configuration
Refer to the following sections for instructions about how to remove or replace the processor, the
memory modules, the expansion cards, and the system battery. The procedure for installing the
Lights-Out 100c remote management card option is also provided.
Processor
The LGA775 processor socket supports the following processor models:
•
•
•
•
•
Quad-Core Intel Xeon Processor
Dual-Core Intel Xeon Processor
Dual-Core Intel Pentium Processor
Intel Core 2 Duo Processor
Intel Celeron Processor 400 Sequence
Processor installation guidelines
When configuring the processor, observe the following important guidelines:
•
Handle the processor and heat sink fan (HSF) with care. Damage to either may prevent the
system from functioning properly.
•
Never touch the processor contact pins; contaminant on the contact pins can damage the
processor.
•
Be sure that the server has the most recent ROM version. Failure to flash the ROM before
installing processors can cause system failure.
Removal and replacement procedures
42
Processor installation
WARNING: To reduce the risk of personal injury from hot surfaces, allow the heat sink fan and the
processor to cool before touching them.
CAUTION: To prevent the heat sink fan from tilting to one side during installation/removal
procedures, observe a diagonally opposite pattern (an “X” pattern) when loosening and tightening
the four spring loaded screws.
The procedure for replacing the current processor consists of five major steps which are as follows:
1.
Remove the heat sink fan (HSF).
2.
Remove the current processor.
3.
Apply the thermal compound.
4.
Install the new processor.
5.
Install the heat sink fan.
To remove the heat sink fan:
1.
Prior to removing the heat sink fan, power on the system for a few minutes to soften the thermal
compound, so that the HSF can easily be removed.
2.
Perform the pre-installation procedure.
3.
Lay the server on its side (components showing).
4.
Remove the heat sink fan.
a. Disconnect the HSF cable from its system board connector (1).
b. Use a T-15 Torx screwdriver to loosen the HSF’s four spring-loaded screws (2).
c.
Lift the HSF away from the system board (3).
You may need to rotate the HSF a few degrees clockwise and counterclockwise to break the
thermal compound bond.
Removal and replacement procedures
43
To remove the old processor:
1.
Rotate the load lever to the open position.
2.
Open the retention plate to expose the socket body.
3.
Gently lift the processor out of its socket.
4.
Place the old processor on a static-dissipating work surface or inside an anti-static bag.
To apply thermal compound:
Perform the procedure below only if you will be using the same heat sink fan as before. If you are
using a new one, there is no need to apply thermal compound as there is already a preapplied
thermal compound in a new HSF.
CAUTION: Applying too little thermal compound will cause a gap between the contact surfaces. This
means that the HSF is not even in direct contact with the processor, and therefore its capacity to
draw out heat is greatly reduced. Furthermore, applying too much compound can make it squish out
from the sides and go all over the processor pins or to the system board when the HSF is installed.
The compound may cause electrical shorts that can damage the system.
1.
Use the alcohol pad (included in the new processor spare kit) to clean the contact surfaces on
the HSF and the new processor. Wipe the contact surfaces several times to make sure that no
particles or dust contaminants are evident. Allow the alcohol to evaporate before continuing.
CAUTION: Do not touch the contact surfaces as this may leave dead skin cells or oils from your
finger that can result in poor thermal compound performance.
Removal and replacement procedures
44
2.
Apply 0.5 gram (0.25 ml) of the thermal compound evenly onto the top of the processor. The
figure below shows the correct pattern of applying the thermal compound.
To install the new processor:
1.
With the load lever and the retention plate still disengaged, align the processor with the socket
and install the processor.
Make sure that the two notches and the orientation arrow on the processor are properly aligned
with the tabs and beveled corner of the socket.
2.
Close down the retention plate.
3.
Rotate the load lever to the lock position.
Removal and replacement procedures
45
To install the heat sink fan:
CAUTION: To prevent overheating or a possible system crash, use only a heat sink fan specified for
the HP ProLiant ML110 Generation 5 server.
1.
If you are using a new HSF, remove the cover protecting the preapplied thermal compound.
Be careful not to touch or scratch the thermal compound.
IMPORTANT: Make sure the HSF cable is not caught underneath the HSF during installation.
2.
Install the heat sink fan.
a. Insert the HSF’s spring-loaded screws into the system board holes (1).
b. Use a T-15 Torx screwdriver to tighten the spring-loaded screws (2).
c.
3.
Connect the HSF cable to its system board connector (3).
Perform the post-installation procedure.
Removal and replacement procedures
46
Memory
The system has four DIMM slots that support up to 8 GB maximum system memory (2 GB in each of
the four DIMM slots). The DIMM slots are divided into two channels of two DIMM slots each.
Memory installation guidelines
Observe the following important guidelines when installing memory modules:
•
Use only HP supported PC2-6400 DDR2-800 unbuffered ECC DIMM in 512 MB, 1 GB or 2 GB
capacities.
•
Supported DIMM configurations include:
○ Single DIMM (non-interleaving) – It must be installed in the DIMM 1A slot.
○ Two DIMMs (interleaving) – For optimum memory performance, populate DIMM slots 1A and
3B.
○ Four DIMMs
CAUTION: DIMMs can be damaged by improper handling. Always use an anti-static wrist
strap and grounding mat, and discharge static electricity before touching DIMMs.
To install a memory module:
1.
Perform the pre-installation procedure.
2.
Lay the server on its side (components showing).
3.
If necessary, remove any accessory boards or cables that prevent access to the DIMM slots.
4.
Locate an empty DIMM slot on the system board.
5.
If necessary, open the holding clips of the selected DIMM slot.
6.
Remove the memory module from its protective packaging, handling it by the edges.
Removal and replacement procedures
47
7.
Install the memory module.
a. Use both hands to hold the module by the edges, and then insert it perpendicularly into the
slot (1).
The DIMM slots are structured to ensure proper installation. If you insert a memory module
but it does not fit easily into the slot, you may have inserted it incorrectly. Reverse the
orientation of the module and insert it again.
b. Press the module at both ends to seat it fully into the slot (2).
The holding clips will automatically lock into place once the module has been seated
properly.
8.
Perform the post-installation procedure.
Removal and replacement procedures
48
Expansion board
Your ProLiant server has four expansion slots with three separate bus channels.
Item
Connector code
Slot type
1
PCI4
PCI Express x8 link with x8 slot
2
PCI3
PCI Express x1 link with x8 slot
3
PCI2
PCI Express x1 link with x8 slot
4
PCI1
32-bit/33 MHz 3.3 V PCI slot
IMPORTANT: The SAS controller board required for a SAS hard drive configuration should be
installed in the PCI3 slot.
To install an expansion board:
1.
Perform the pre-installation procedure.
2.
Prepare the system for the expansion board installation.
a. Loosen the PCI slot cover retainer thumbscrew (1).
b. Detach the PCI slot cover retainer from the chassis (2).
c.
Identify the slot that is compatible with the expansion board you intend to install, and then
pull out its slot cover (3).
Store it for reassembly later.
CAUTION: Do not discard the slot cover. If the expansion board is removed in the future,
the slot cover must be reinstalled to maintain proper cooling
Removal and replacement procedures
49
3.
Remove the expansion board from its protective packaging, handling it by the edges.
4.
Install the expansion board.
a. Slide the expansion board into the selected slot, and then press it down to seat it
properly (1).
b. Slide the PCI slot cover retainer toward the slots covers (2).
c.
Tighten the PCI slot cover retainer thumbscrew (3).
d. Connect the necessary cables to the board.
Refer to the documentation that came with the board.
5.
Perform the post-installation procedure.
Removal and replacement procedures
50
Lights-Out 100c remote management card (IPMI card)
This section provides instructions for installing the HP Lights-Out 100c remote management card (IPMI
2.0 compliant). This option allows users to perform server management tasks remotely over a LAN or
the Internet. It also has a health monitoring function that tracks and records system events related to
the fan status, system temperature, and voltage condition. The Lights-Out 100c upgrade connector is
shown in the figure below.
To install the IPMI card:
1.
Perform the pre-installation procedure.
2.
Locate the Lights-Out 100c upgrade connector on the system board.
3.
If necessary, remove any components or cables that prevent access to the slot.
4.
Remove the Lights-Out 100c blank bracket.
a. Remove the screw securing the bracket (1).
b. Pull the bracket out of the chassis (2).
Removal and replacement procedures
51
5.
Remove the IPMI card from its protective packaging.
6.
Do a visual check to see if the bracket attached to the IPMI card fits the chassis of your ProLiant
server.
If the bracket fits, install the IPMI card. Proceed to step 9 for instructions.
If the bracket does not fit your server chassis, select and attach a compatible one from the two
additional brackets included in the option kit. Proceed to the next step for instructions.
7.
Select a compatible bracket from the two bracket options.
8.
Change the IPMI card’s default bracket.
a. Remove the two screws securing the default bracket to the IPMI card (1).
Use these screws to attach the compatible bracket later.
b. Detach the default bracket from the IPMI card (2).
c.
Align the screw holes on the new bracket with those located on the IPMI card (3).
d. Use the two screws you removed in step a to secure the new bracket to the IPMI card (4).
Removal and replacement procedures
52
The figure below shows both additional brackets. Choose the one that is compatible with
your ProLiant server’s chassis.
Removal and replacement procedures
53
9.
Install the IPMI card.
a. Align the card with the Lights-Out 100c upgrade connector, and then firmly seat the card on
the slot (1).
b. Secure the card with the screw you removed in step 4-a (2).
10.
Perform the post-installation procedure.
System battery
The server uses a nonvolatile memory that requires a battery to retain system information when power
is removed. This 3-volt 200-mAh lithium coin cell battery is located on the system board.
If the server no longer automatically displays the correct date and time, the system battery that
provides power to the real-time clock may need to be replaced. Under normal use, battery life is 5 to
10 years.
Removal and replacement procedures
54
System battery replacement warnings
Observe the following reminders when replacing the system battery:
•
Replace the battery with the same type as the battery recommended by HP. Use of another
battery may present a risk of fire or explosion.
•
A risk of fire and chemical burn exists if the battery is not handled properly. Do not disassemble,
crush, puncture, or short external contacts, or expose the battery to temperatures higher than
60°C (140°F).
•
Do not dispose of used battery in water or fire. Dispose of used batteries according to
manufacturer's instructions.
•
Loss of BIOS settings occurs when the battery is removed. BIOS settings must be reconfigured
whenever the battery is replaced.
To replace the system battery:
1.
Perform the pre-installation procedure.
2.
Lay the server on its side (components showing).
3.
If necessary, remove any accessory boards or cables that prevent access to the battery socket.
4.
Locate the system battery.
5.
Replace the system battery.
a. Squeeze the metal clamp that extends above one edge of the battery until the battery pops
up (1).
b. Lift up the old battery to remove it (2).
Removal and replacement procedures
55
c.
Slide one edge of the replacement battery under the holder’s lip, and then push the other
edge down until the clamp snaps over the battery.
Make sure the battery’s positive side is facing up.
6.
Perform the post-installation procedure.
System fan
A new system fan can be installed to allow the server to operate properly in case the default system
fan becomes defective.
To replace the system fan:
CAUTION: Be sure to support the system fan with your hand when removing screws from the
chassis. The fan could fall onto the system board or an accessory board causing damage if not
supported.
1.
Perform the pre-installation procedure.
2.
Remove the default system fan:
a. Disconnect the system fan cable from its system board connector (1).
b. From inside the chassis, slightly detach the fan from the chassis, and then pull the four rubber
bolts through their chassis holes (2).
c.
Remove the fan from the chassis (3).
Removal and replacement procedures
56
3.
Install the new system fan.
a. Align the rubber bolts to their chassis holes (1).
b. While holding the new fan against the chassis, pull the rubber bolts through their chassis
holes (2).
c.
4.
Connect the system fan cable to its system board connector (3).
Perform the post-installation procedure.
Removal and replacement procedures
57
Power supply unit
Located on the rear panel of the server is a single standard autoranging 365-watts power supply unit
(PSU).
PSU replacement warnings
Observe the following reminders to reduce the risk of personal injury from electric shock hazards
and/or damage to the equipment
•
Installation of the power supply unit should be referred to individuals who are qualified to service
server systems and are trained to deal with equipment capable of generating hazardous energy
levels.
•
DO NOT open the power supply unit. There are no serviceable parts inside it.
To replace the power supply unit:
1.
Perform the pre-installation procedure.
2.
Disconnect the system power cables.
Go to page 34 for an illustration of these cable connections.
○ Processor power cable
○ System board power cable
○ System drives’ power cables
3.
Remove the default power supply unit.
a. Remove the four screws that secure the PSU to the chassis (1).
b. Detach the PSU from its chassis bay, and then remove it from the system (2).
Removal and replacement procedures
58
4.
Install the new power supply unit.
a. Align the new PSU to its chassis bay (1).
b. Secure the PSU to the chassis using the four screws you removed in step 3-a (2).
5.
Reconnect the system power cables you removed in step 2.
6.
Perform the post-installation procedure.
Removal and replacement procedures
59
Diagnostic tools
Troubleshooting resources
NOTE: For common troubleshooting procedures, the term "server" is used to mean servers and
server blades.
The HP ProLiant Servers Troubleshooting Guide provides simple procedures for resolving common
problems as well as a comprehensive course of action for fault isolation and identification, error
message interpretation, issue resolution, and software maintenance.
To obtain the guide, refer to any of the following sources and then select the HP ProLiant Servers
Troubleshooting Guide:
•
•
•
The server-specific Documentation CD
The Business Support Center on the HP website (http://www.hp.com/support). Navigate to the
server technical support page. Under self-help resources, select ProLiant Troubleshooting Guide.
The Technical Documentation website (http://www.docs.hp.com). Select Enterprise Servers,
Workstations and Systems Hardware, and then the appropriate server.
HP Insight Diagnostics
HP Insight Diagnostics is a proactive server management tool, available in both offline and online
versions, that provides diagnostics and troubleshooting capabilities to assist IT administrators who
verify server installations, troubleshoot problems, and perform repair validation.
HP Insight Diagnostics Offline Edition performs various in-depth system and component testing while
the OS is not running. To run this utility, launch the Support CD.
HP Insight Diagnostics Online Edition is a web-based application that captures system configuration
and other related data needed for effective server management. Available in Microsoft® Windows®
and Linux versions, the utility helps to ensure proper system operation.
For more information or to download the utility, refer to the HP website
(http://www.hp.com/servers/diags).
Survey Utility
Survey Utility, a feature within HP Insight Diagnostics, gathers critical hardware and software
information on ProLiant servers.
This utility supports operating systems that may not be supported by the server. For operating systems
supported by the server, refer to the HP website (http://www.hp.com/go/supportos).
If a significant change occurs between data-gathering intervals, the Survey Utility marks the previous
information and overwrites the Survey text files to reflect the latest changes in the configuration.
Diagnostic tools
60
Array Diagnostic Utility
The HP Array Diagnostics Utility is a web-based application that creates a report of all HP storage
controllers and disk drives. This report provides vital information to assist in identifying faults or
conditions that may require attention. ADU can be downloaded from the HP website
(http://www.hp.com).
Phoenix BIOS software
Your ProLiant server uses BIOS to boot up the system. Phoenix BIOS software is a ROM BIOS-based
firmware that allows reliability, manageability, and connectivity for server platforms. This software
contains a set of programs permanently stored in an EEPROM chipset located on the system board.
These programs assist in managing, initializing, and testing the hardware devices installed on the
computer.
The Phoenix BIOS software serves three functions:
•
Configure the system from the Phoenix BIOS Setup Utility
Using the Setup program, you can install, configure, and optimize the hardware devices on your
system (clock, memory, disk drives, etc.). In addition, you can enable various features such as
serial console redirection, PXE boot, and much more.
•
Initialize hardware at boot using POST routines
During power-on or warm reset, the software performs Power-On Self-Test (POST) routines to test
components, to allocate resource for various hardware devices, and to prepare the system to
boot to various operating systems.
•
Perform run-time routines
Using the software, perform basic hardware routines that can be called from DOS and Windows
applications.
Configuring the system BIOS
NOTE: For ease of reading, Phoenix BIOS Setup Utility will be simply referred to as “Setup” or
“Setup Utility” in this guide. Also, the screenshots used in this guide display various Setup menu
screens with the default values identified. These values may not be the same as those in your server.
Phoenix BIOS Setup Utility is a hardware configuration program built into your system's Basic
Input/Output System (BIOS). Since most systems are already properly configured and optimized,
there is normally no need to run this utility.
You will need to run this utility under the following conditions:
•
When changing the system configuration including:
○
○
○
○
○
○
Setting the system time and date
Configuring the hard drives
Specifying the boot device sequence
Installing PCI expansion boards
Upgrading the system BIOS
Configuring the power management modes
Diagnostic tools
61
○ Setting up system passwords or making other changes to the security setup
•
When a configuration error is detected by the system and you are prompted (Run Setup
message) to make changes to the BIOS settings.
NOTE: If you repeatedly receive Run Setup messages, the system battery may be defective. In this
case, the system cannot retain configuration values in CMOS. Replace the system battery with a
new one.
The Setup Utility loads the configuration values in a battery-backed nonvolatile memory called CMOS
RAM. This memory area is not part of the system RAM, which allows configuration data to be
retained when power is turned off. The values take effect when the system is booted. POST uses these
values to configure the hardware. If the values and the actual hardware do not agree, POST
generates an error message. You must run this utility to change the BIOS settings from the default or
current configuration.
The Setup Utility has five primary menu selections, including:
•
•
•
•
•
Main
Advanced
Security
Boot
Exit
To run the Setup Utility:
1.
Turn on the monitor and the server.
If the server is already turned on, save your data and exit all open applications, and then restart
the server.
2.
During POST, press F10.
If you fail to press F10 before POST is completed, you will need to restart the server.
The first page to be displayed will be the Main menu showing the Setup Utility’s menu bar. Use
the left (Å) and right (Æ) arrow keys to move between selections on the menu bar.
Diagnostic tools
62
Setup Utility navigation keys
Use the following keyboard keys to work your way through the various menu and submenu screens of
the Setup Utility.
Key
Functions
← and →
To move between selections on the menu bar.
↑ and ↓
To move the cursor to the field you want.
The currently selected field will be highlighted. The right side of each menu screen
displays the Item Specific Help panel. This panel displays the help text for the currently
selected field. It updates as you move the cursor to each field.
PgUp and PgDn
To move the cursor to the previous and next page of a multiple page menu.
Home
To move the cursor to the first page of a multiple page menu.
End
To move the cursor to the last page of a multiple page menu.
(+) , (–), and
<Space>
To select a value for the currently selected field (only if it is user-configurable).
Press the (+), (–), or <Space> keys repeatedly to display each possible entry, or the Enter
key to choose from a pop-up menu.
A parameter that is enclosed in square brackets [ ] is user-configurable.
Grayed-out parameters are not user-configurable for one of the following reasons:
• The field value is auto-configured or auto-detected.
• The field value is informational only.
• The field is password-protected.
Enter
To select a field value or display more options for menu marked with ►.
Ctrl+Enter
To expand all device lists.
F1 or <Alt+H>
To bring up the General Help window.
The General Help window describes other Setup navigation keys that are not displayed
on the legend bar.
Esc or <Alt+X>
If you press this key:
• On one of the primary menu screens, the Exit menu displays.
• On a submenu screen, the previous screen displays.
• When you are making selections from a pop-up menu, closes the pop-up without
making a selection.
F9
Loads the default system values.
F10
Saves changes and closes the Setup Utility.
Diagnostic tools
63
Setup Utility menus
The Setup Utility provides a menu bar with the menu selections. The menu bar choices are described
in the following sections.
Main menu
Main
Phoenix BIOS Setup Utility
Advanced
Security
Boot
ProLiant BIOS
BIOS Version
Build Date
O15
V0.18
08/01/07
CPU Type
CPU Speed
Physical CPUs
Installed Memory
Intel® Xeon® CP
2.40 GHz
1 of 1 Enable
1024MB
Embedded NIC1 MAC Address :
Set Server Asset Text :
Set Serial Number Text :
Boot Features
System Time
System Date:
F1 Help
ESC Exit
Exit
Item Specific Help
<Tab>, <Shift-Tab>, or
<Enter> selects field
001018000000
[0123456789abcde]
0123456789ABCDEF
[16:19:20]
[12/08/2003]
↑↓ Select Item
←→ Select Menu
-/+
Change Values
F9 Setup Defaults
Enter Select Sub-Menu F10 Save and Exit
Field
Description
ProLiant BIOS
System BIOS name
BIOS Version
System BIOS version
Build Date
Date when the Setup BIOS was created
CPU Type
Processor model name
CPU Speed
Processor speed
Physical CPUs
Number of installed processors
Installed Memory
System memory size detected during POST
Embedded NIC1 MAC Address
MAC address of the embedded NIC
Set Server Asset Text
Enter the server asset tag and serial number. These information are printed
on the serial label located on the rear panel.
Set Serial Number Text
Boot Features
Set which options to run during system bootup.
Press Enter to access the related submenu.
System Time
Adjust the system time.
System Date
Adjust the system date.
Diagnostic tools
64
Advanced menu
Main
Phoenix BIOS Setup Utility
Advanced
Security
Boot
Advanced Chipset Control
Advanced Processor Options
I/O Device Configuration
Hard Disk Configuration
USB Configuration
Console Redirection
IPMI
Reset Configuration Date :
F1 Help
ESC Exit
↑↓ Select Item
←→ Select Menu
Exit
Item Specific Help
<Tab>, <Shift-Tab>, or
<Enter> selects field
[No]
-/+
Change Values
F9 Setup Defaults
Enter Select Sub-Menu F10 Save and Exit
Field
Description
Advanced Chipset Control
Displays the settings related to the system chipsets.
Press Enter to access the related submenu.
Advanced Processor Options
Displays the settings related to the processor.
Press Enter to access the related submenu.
I/O Device Configuration
Displays the settings related to the serial port.
Press Enter to access the related submenu.
Hard Disk Configuration
Displays the settings related to the system hard drives.
Press Enter to access the related submenu.
USB Configuration
Displays the settings related to the USB function.
Press Enter to access the related submenu.
Console Redirection
Displays console redirection-related settings.
Press Enter to access the related submenu.
IPMI
Displays server management-related settings.
Press Enter to access the related submenu.
Reset Configuration Data
Select whether to erase data in the section of memory for ESCD (Extended
System Configuration Data) which stores the configuration settings for
non-PnP plug-in devices.
Diagnostic tools
65
Security menu
Main
Phoenix BIOS Setup Utility
Advanced
Security
Boot
Exit
Item Specific Help
Supervisor Password Is : Clear
Set Supervisor Password
[Enter]
Password on Boot:
[Disabled]
F1 Help
ESC Exit
↑↓ Select Item
←→ Select Menu
<Tab>, <Shift-Tab>, or
<Enter> selects field
-/+
Change Values
F9 Setup Defaults
Enter Select Sub-Menu F10 Save and Exit
Field
Description
Supervisor Password Is
Current supervisor password status (Clear or Enabled)
Set Supervisor Password
Select the field, and then press Enter to set, change, or remove a supervisor
password.
Password on Boot
Select whether to require the supervisor password during bootup.
Supervisor password
The Security menu allows users to set a supervisor password. When entered, this password will allow
the user to access and change all settings in the Setup Utility.
To set a supervisor password:
1.
In the Security menu screen, select the Set Supervisor Password field then press Enter.
2.
Type a new password in the password box.
The password may consist of up to eight alphanumeric characters (A-Z, a-z, 0-9).
3.
Retype the password to verify the first entry, and then press Enter.
4.
Press F10 to save the password and close the Setup Utility.
After setting the password, the Supervisor Password Is field value is set to Enabled.
To change the supervisor password:
1.
In the Security menu screen, select the Set Supervisor Password field, and then press Enter.
2.
Type the original password in the password box.
3.
Type a new password, and then press Enter.
4.
Retype the new password to verify the first entry, and then press Enter again.
5.
Press F10 to save the password and close the Setup Utility.
Diagnostic tools
66
To remove the supervisor password:
1.
In the Security menu screen, select the Set Supervisor Password field, and then press Enter.
2.
Type the original password then press Enter.
3.
Press Enter twice without entering anything in the new and confirm password fields.
4.
Press F10 to save the changes you made and close the Setup Utility.
The Supervisor Password Is field value is set to Clear.
To reset the supervisor password:
If you forget the supervisor password, you need to clear the CMOS and reset the BIOS settings to
regain access the Setup Utility. For instructions, refer to the “Clearing CMOS” section on page 70.
Boot menu
Use this menu to set the preferred drive sequence in which the Setup Utility attempts to boot the
operating system.
By default, the server searches for boot devices in the following order:
•
•
•
•
CD-ROM/DVD-ROM drive
Removable device
Hard drive
Embedded NIC (via Preboot Execution Environment—remote boot over LAN)
To implement the PXE boot option, you need to first set the Embedded NIC2 PXE field to Enabled.
Main
Phoenix BIOS Setup Utility
Advanced
Security
Boot
CD-ROM/DVD-ROM
Removable Devices
+Hard Drive
Embedded NIC
Exit
Item Specific Help
<Tab>, <Shift-Tab>, or
<Enter> selects field
Embedded NIC1 PXE ; [Enabled]
F1 Help
ESC Exit
↑↓ Select Item
←→ Select Menu
-/+
Change Values
F9 Setup Defaults
Enter Select Sub-Menu F10 Save and Exit
Diagnostic tools
67
Exit menu
Main
Phoenix BIOS Setup Utility
Advanced
Security
Boot
Exit Saving Changes
Exit Discarding Changes
Load Setup Default
Discard Changes
Save Changes
F1 Help
ESC Exit
↑↓ Select Item
←→ Select Menu
Exit
Item Specific Help
<Tab>, <Shift-Tab>, or
<Enter> selects field
-/+
Change Values
F9 Setup Defaults
Enter Select Sub-Menu F10 Save and Exit
Field
Description
Exit Saving Changes
Saves changes made and closes the Setup Utility.
Keyboard shortcut: F10
Exit Discarding Changes
Discards changes made and closes the Setup Utility.
Load Setup Default
Loads the factory-default settings for all Setup parameters.
Keyboard shortcut: F9
Discard Changes
Discards all changes made to the Setup Utility and loads the previous
configuration settings.
Save Changes
Saves all changes made to the Setup Utility.
Boot-time diagnostic screen
The boot-time diagnostic screen displays basic and important information about the current server
configuration and is necessary for troubleshooting and may be required when asking for technical
support. It is recommended that you check this screen during the initial system setup and each time
you install, remove, or upgrade accessories.
To view the boot-time diagnostic screen:
You first need to enable the display of the diagnostic screen during bootup. Follow the steps below.
1.
In the Main menu screen, select Boot Features, and then press Enter.
2.
Select the Boot-time Diagnostic Screen field.
3.
Press the plus (+) or minus (–) key to set the field to Enabled.
4.
Press F10 to save the changes you made and close the Setup Utility.
Diagnostic tools
68
5.
Reboot the server.
The diagnostic screen is displayed briefly at the end of POST.
Phoenix cME FirstBIOS Pro Setup Utility
CPU Type
CPU Speed
Physical CPUs
Installed Memory
:
:
:
:
Genuine Intel ® CPU @ 2.3 Ghz
2.30 GHz
Logical CPUs
1 of 1 Enabled
System ROM
1024 MB
Build Date
Hard Disk 1
Hard Disk 2
Hard Disk 3
: None
: None
: None
Hard Disk 4
Hard Disk 5
Hard Disk 6
: 4 of 4 Enabled
: E617 – FFFF
: 09/10/2007
: None
: None
: None
6.
Press the Pause/Break key to continue displaying the screen until another key is pressed.
7.
Press any key to continue with the system bootup.
Updating the system BIOS
Perform the steps below to update the system BIOS.
1.
Go to www.hp.com and download the following files to the root directory of a bootable device.
You can use a diskette, an external USB drive, or a CD/DVD.
○
○
○
○
ROMPAQ.exe
CPQSRVR2.cpu
CPQO1501.xxx
CONFIG.sys
2.
Create and label a bootable ROMPAQ device using the downloaded files.
3.
Reboot the server using the bootable ROMPAQ device.
4.
Follow the onscreen instructions to update the system BIOS.
Recording custom Setup values
Keep a record of the custom Setup values you have set up for your system BIOS. If the custom values
ever need restoring (after a CMOS clear, for example) you must run the Setup Utility and enter these
custom settings again. Make sure to update this record whenever you make any change to these
Setup settings or install new hardware.
You can either record the Setup values manually (hard copy) or use a CMOS backup utility.
To manually record the custom Setup values:
1.
Access the Setup utility.
2.
Go through each menu and submenus page, and press Print Screen to make a hard copy.
3.
For multiple page menus, move to each page and print each screen.
If a printer is not available, write down the values on a piece of paper. Make sure to write them
down legibly and accurately.
4.
Label and date the Setup values hard copy, and then store it in a safe and accessible place,
preferably with other user documentation for your ProLiant server.
Diagnostic tools
69
CMOS backup utility
There are third-party utilities that read the CMOS settings and record them to a regular file, which can
then be backed up through normal means, or copied to an external storage media. Some of these
utilities also offer the option of restoring the CMOS settings so you need not re-enter them manually.
These utilities are not always compatible with all versions of CMOS or types of CMOS. In addition,
these utilities are not compatible with all operating system versions. Be sure to use a CMOS backup
utility that is designed for the particular CMOS type and OS version installed in your ProLiant server.
For information on a compatible CMOS backup utility, contact your local HP representative.
Loading system defaults
If your system fails after you make changes in the Setup menus, reboot the server, enter Setup and
load the system default settings to correct the error. These default settings have been selected to
optimize your server’s performance.
To load the system defaults:
1.
Reboot the server in a normal manner.
2.
During POST, press F10 to access the Setup Utility.
3.
Press F9 to load the default values.
4.
Press F10 to save the changes you made and close the Setup Utility.
Clearing CMOS
You may need to clear the Setup configuration values (CMOS) if the configuration has been
corrupted, or if incorrect settings made in the Setup Utility caused error messages to be unreadable.
Clearing the CMOS data removes the supervisor password.
Use the JP7 jumper to clear the CMOS data.
•
•
1-2 position: Normal operation (default)
2-3 position: Clear CMOS data
Diagnostic tools
70
To clear CMOS:
1.
Perform the pre-installation procedure.
2.
If necessary, remove any expansion boards, assemblies or cables that prevent access to the
CMOS clear jumper.
3.
Locate the clear CMOS jumper on the system board.
4.
Remove the jumper block and set it over the 2-3 pins for 20 to 30 seconds.
5.
Return the jumper block to its default 1-2 position.
6.
Perform the post-installation procedure.
7.
During POST, press F10 to access the Setup Utility.
8.
Press F9 to load the system default values.
9.
Press F10 to save the changes you made and close the Setup Utility.
Power-On-Self-Test
Before you can use a server, all devices must be tested and initialized, and the operating system must
be bootstrapped to the memory. This is referred to as Power-On-Self-Test or POST. POST is a series of
diagnostic tests that checks firmware and hardware components to ensure that the server is properly
functioning. This diagnostic function automatically runs each time the server is powered on.
These diagnostics, which reside in the BIOS ROM, isolate server-related logic failures and indicate the
board or component that needs to be replaced, as indicated by the error messages. Most server
hardware failures will be accurately isolated during POST. The number of tests displayed depends on
the configuration of the server.
During POST you can press:
•
•
•
Esc to skip the HP logo and go to POST boot progress display system summary screen.
F10 to access the Setup Utility.
F12 to request a network boot (PXE).
POST error indicators
When POST detects a system failure, it either displays a POST error message, or emits a series of
beep codes.
POST errors messages
Whenever a non-critical error occurs during POST, an error message describing the problem appears
onscreen. These text messages are displayed in normal video (white text on black background). It
shows the details of the error. The following is an example of a POST error message:
ERROR
0251: System CMOS checksum bad – Default configuration used
Diagnostic tools
71
In some cases an error message may include recommendations for troubleshooting or require that you
press the Enter key to display recommendations. Follow the instructions on the screen.
The next table lists the most common POST error messages with their corresponding troubleshooting
recommendation. It is recommended that you correct the error before proceeding, even if the server
appears to boot successfully.
If your system displays one of the messages marked below with an asterisk (*), write down the code
and message and contact your HP Customer Support provider.
When no POST error message is displayed but the server stops during POST, listen for beep codes.
Error code
Error message
Corrective action/description
0200
Failure Fixed Disk
Fixed disk is not working or not configured
properly.
1 Run Setup and check if the fixed-disk type is
2
0210
Stuck key
Stuck key on keyboard.
1 Locate the stuck key on your keyboard and release
2
0211
Keyboard error
correctly identified.
Check to see if the fixed disk is attached properly.
it.
Reboot the server.
Keyboard not working.
Verify that the keyboard cable is securely
connected to the keyboard port (not the mouse
port) on the rear panel of the server.
If the problem persists, replace the keyboard or
contact your HP Customer Support provider.
0212
Keyboard Controller Failed
Keyboard controller failed test.
0213
Keyboard locked - Unlock key switch
Keyboard error. Replace the keyboard.
0220
Monitor type does not match CMOS Run SETUP
The attached monitor cannot be correctly
identified by Setup.
Run Setup and check if the monitor type is
correctly identified.
0230
Shadow RAM Failed at offset: nnnn
0231
System RAM Failed at offset: nnnn
0232
Extended RAM Failed at offset: nnnn
0250
System battery is dead - Replace and
run SETUP
One or more defective memory module.
1 Remove all installed DIMMs.
2 Reinstall the DIMMs one by one to identify the
3
defective module.
Replace the DIMM with a new one.
The CMOS clock battery indicator shows the
system battery is dead.
1 Replace the system battery following the
2
procedures on page 54.
Run Setup to reconfigure the system.
Diagnostic tools
72
Error code
Error message
Corrective action/description
0251
System CMOS checksum bad - Default
configuration used
The settings in the Setup Utility have been
corrupted or modified incorrectly, perhaps by an
application program that changes data stored in
CMOS.
Access Setup, and then either load the system
default values or enter your own custom values. If
the error persists, check the system battery or
contact your HP Customer Support provider.
0260
System timer error
The timer test failed. Requires repair of the
system board.
0270
Real time clock error
Real-Time Clock (RTC) fails BIOS hardware test.
May require board repair.
0271
Check date and time settings
BIOS found date or time is out of range. May
require setting legal date (1991-2099).
Access Setup and check the values in the System
Time and System Date fields of the Main menu.
0280
Previous boot incomplete - Default
configuration used
Initial bootup failed. BIOS automatically loads
the default system values and then boots again.
0281
Memory size found by POST differed
from CMOS
The user added or removed a memory module,
thus the system memory size is different from the
previous bootup value.
02D0
System cache error - Cache disabled
Processor error. Replace the processor.
02F0
CPU ID:
–
02F4
EISA CMOS not writeable
System board failure. Replace the system board.
02F5
DMA Test Failed
The DMA control test failed.
02F6
Software NMI Failed
An NMI signal is detected.
Diagnostic tools
73
POST related troubleshooting
Perform the following procedures when POST fails to run, displays error messages, or emits beep
codes.
If the POST failure is during a routine boot up, check the following:
•
•
•
All external cables and power cables should be firmly plugged in.
•
•
•
•
•
•
The monitor's contrast and brightness settings are correct.
•
•
All system cables are securely connected and are in their proper order.
The power outlet to which the server is connected and is working.
The server and monitor are both turned on. The bicolor status LED indicator on the front panel
must be lit up green.
All internal cables are properly connected and all boards are firmly seated.
The processor is fully seated in its socket on the system board.
The heat sink is properly installed on top of the processor.
All memory modules are properly installed.
If you have installed a PCI expansion board, verify that the board is firmly seated and any
switches or jumpers on the board are properly set. Refer to the documentation provided with the
expansion board.
If you have changed any switches on the system board, verify that each is properly set.
Diagnostic tools
74
Connectors, switches, and LEDs
Connectors and components
Front panel
Item
Icon
Component
1
Optical disc drive (ODD)
2
ODD manual eject hole
3
ODD eject button
4
Power button
5
Front USB 2.0 ports
6
HDD EMI shield
7
HDD EMI shield screw
8
2nd removable media drive bay EMI shield
NOTE: The location of items 2 and 3 may vary depending on the model of the installed removable media drive.
Connectors, switches, and LEDs
75
Rear panel
Item
Icon
Component
1
Kensington lock notch
2
Access panel thumbscrew
3
Cable lock provision notch
4
PCI slot cover retainer
5
PCI slot cover retainer thumbscrew
6
PCI1 slot cover
7
PCI2 slot cover
8
PCI3 slot cover
9
PCI4 slot cover
10
Lights-Out 100c management port (with option installed)
11
Embedded NIC port (RJ-45)
12
Rear USB 2.0 ports
13
Serial port
14
Video port
15
PS/2 keyboard port
16
PS/2 mouse port
17
Power supply cable socket
Connectors, switches, and LEDs
76
System board
Item
Component code
Component
1
DIMM 4B
Channel B 2nd DDR II DIMM slot
2
DIMM 3B
Channel B 1st DDR II DIMM slot
3
DIMM 2A
Channel A 2nd DDR II DIMM slot
4
DIMM 1A
Channel A 1st DDR II DIMM slot
5
JP5
CPU fan connector
6
CN11
HDD LED cable connector (for SAS HDD)
7
SATA6
2nd removable media drive SATA cable connector
8
SATA5
1st removable media drive SATA cable connector
9
SATA4
4th HDD SATA cable connector
10
SATA3
3rd HDD SATA cable connector
11
SATA2
2nd HDD SATA cable connector
12
SATA1
1st HDD SATA cable connector
13
FPCN1
Front panel board connector
14
FPUSBCONN1
Front panel USB port connector
15
USBCONN3
Internal USB connector for STD USB
16
USBCONN2
Internal USB connector for tape device
17
BAT1
System battery
18
PCI1
32-bit/33 MHz 3.3 V PCI slot
19
PCI2
PCI Express x1 link with x8 slot
20
PCI3
PCI Express x1 link with x8 slot
Connectors, switches, and LEDs
77
Item
Component code
Component
21
PCI4
PCI Express x8 link with x8 slot
22
CN5
Lights-Out 100c upgrade connector
23
JP4
System fan cable connector
24
CPU1
Processor
25
PWRCN1
4-pin ATX processor power connector
26
ATXPWRCN1
24-pin ATX system board power connector
Connectors, switches, and LEDs
78
Status LED indicators
The status LED indicators aid in problem diagnosis by indicating the status of system components and
operations of the server.
External LED indicators
Item
Indicator
Status
Description
1
Embedded NIC link
Orange
10/100 Mbps connection
Green
Gigabit connection
2
Embedded NIC activity
Blinking yellow
Ongoing network activity
3
Management NIC activity
Blinking green
Ongoing network activity
4
Management NIC link
Green
Existing network link
5
HDD activity
Green
Ongoing HDD activity
6
System power
Green
Power on mode
Amber
Standby mode
Green
Ongoing ODD activity
7
ODD activity
Connectors, switches, and LEDs
79
System board LED indicators
Item
Function
Status
Description
1
DC power on
Green
System is turned on.
2
Standby power
Green
System is in standby mode.
3
Management controller heartbeat
Blinking green
Baseboard Management Controller
(BMC) activity
Connectors, switches, and LEDs
80
System specifications
Hardware specifications
System unit
Item
Component
Processor socket
Intel LGA775
Processor support
•
•
•
•
Core logic chipsets
Intel Pentium Dual-Core
Dual-Core and Quad-Core Intel Xeon
Intel Core 2 Duo
Intel Celeron 400 Sequence
• Intel 3200 MCH (U8) – north bridge, core logic controller
• Intel 82801IR ICH9R (U21) – south bridge
• ServerEngines Pilot 2 (U18) – BMC controller
Hardware monitoring Integrated in the ServerEngines Pilot 2 chip
chipset
LAN controller
NC105i Gigabit Ethernet controller
Memory controller
Integrated in the Intel 3200 MCH
Storage controller
• SATA – Integrated in the Intel 82801IR ICH9R
• SAS – SAS controller board (optional)
VGA controller
Integrated in the ServerEngines Pilot 2 chip
I/O subsystem
•
•
•
•
PCI4 – PCI Express x8 line with x8 slot
PCI2 and PCI3 – PCI Express x1 line with x8 slots
PCI1 – 32-bit/33 MHz 3.3 V PCI slot
CN5 – PCI Express x1 slot dedicated for the Lights-Out remote management card
option
Memory
• Four DDR II slots
• 8 GB maximum system memory (2 GB in each of the four DIMM slots)
• Interleaving mode supported
Media storage
• Two half-height media bays for optical media and storage/tape drives
• Four 3.5-inch bays for non-hot-plug SAS or SATA drives
I/O ports
• Front panel – Two USB ports
• Rear panel – PS/2 keyboard port, PS/2 mouse port, video port, serial port, four
USB ports, embedded NIC port, and Lights-Out 100c management port (with option
installed)
• Internal – Two USB ports for tape drive
System specifications
81
Item
Component
Status LED indicators
• Front panel – Optical drive activity, power, and hard drive activity
• Rear panel – Activity and link status for the embedded/management NIC ports
• System board – DC power on, standby power, and management controller
heartbeat
Server management
HP Lights-Out100c remote management card (optional)
• IPMI 2.0 compliant
• Dedicated 10/100 Mbps LAN port for online system health monitoring
Thermal solution
• One system fan
• One processor heat sink fan
• One PSU fan
Memory
Item
Description
Number of DIMM slots
Four
Maximum memory capacity
8 GB (2 GB in each of the four DIMM slots)
Memory modes
• Single DIMM, non-interleaving (DIMM 1A)
• Two DIMMs, interleaving (DIMM 1A and DIMM 3B)
• Four DIMMs, full memory configuration
Memory controller
Integrated in the Intel 3200 MCH
DIMM specifications
Size
512 MB, 1 GB, and 2 GB
Speed
533/667/800 MHz
Type
PC2-6400 DDR2-800 unbuffered ECC DIMM
Processor
General processor specifications
Item
Description
Manufacturing technology
65 nm
Thermal design power
65W (35W for Intel Celeron 400 Sequence models)
Socket type
LGA775
System specifications
82
Intel Pentium Dual-Core
Specification
Description
Processor number
E2160
E5200
E7400
CPU speed
1.8 GHz
2.5 GHz
2.8 GHz
Bus speed
800 MHz
800 MHz
1066 MHz
Bus/core ratio
9
12.5
10.5
L2 cache size
1 MB
2 MB
3 MB
L2 cache speed
1.8 GHz
2.5 GHz
2.8 GHz
Core stepping
L2
M0
R0
CPUID string
06F2h
10676h
1067 Ah
Thermal specification
61.4°C
74°C
74°C
Core voltage
1.162V–1.312V
0.85V – 1.3625V
0.85V – 1.3625V
Dual-Core Intel Xeon
Specification
Description
Processor number
3065
3075
3085
CPU speed
2.33 GHz
2.66 GHz
3.0 GHz
Bus speed
1333 MHz
1333 MHz
1333 MHz
Bus/core ratio
7
8
9
L2 cache size
4 MB
4 MB
4 MB
L2 cache speed
2.33 GHz
2.66 GHz
3.0 GHz
Core stepping
G0
G0
G0
CPUID string
06FBh
06FBh
06FBh
Thermal specification
60.1°C
60.1°C
60.1°C
Core voltage
0.85---1.3625
0.85---1.3625
0.85---1.3625
System specifications
83
Specification
Description
Processor number
E3110
E3120
CPU speed
3 GHz
3.16 GHz
Bus speed
1333 MHz
1333 MHz
Bus/core ratio
9
9.5
L2 cache size
6 MB
6 MB
L2 cache speed
3 GHz
3.16 GHz
Core stepping
C0
E0
CPUID string
10676h
1067Ah
Thermal specification
72°C
72°C
Core voltage
1.225V-0.956V
1.3625
System specifications
84
Quad-Core Intel Xeon
Specification
Description
Processor number
X3210
X3220
X3320
X3350
CPU speed
2.13 GHz
2.4 GHz
2.5 GHz
2.66 GHz
Bus speed
1066 MHz
1066 MHz
1333 MHz
1333 MHz
Bus/core ratio
8
9
7.5
8
L2 cache size
8 MB
8 MB
6 MB
12 MB
L2 cache speed
2.13 GHz
2.4GHz
2.5 GHz
2.66 GHz
Core stepping
G0
G0
M1
C1
CPUID string
06FBh
06FBh
10676h
10676h
Thermal specification 85°C
85°C
71°C
71°C
Core voltage
1.100V–1.372V
1.100V–1.372V
0.962V-1.212V
0.950V-1.212V
Processor number
X3210
X3220
X3320
X3350
Specification
Description
Processor number
X3330
X3360
X3370
CPU speed
2.66 GHz
2.8 GHz
3 GHz
Bus speed
1333 MHz
1333 MHz
1333 MHz
Bus/core ratio
8
8.5
9
L2 cache size
6 MB
12 MB
12 MB
L2 cache speed
2.66 GHz
2.83 GHz
3.0 GHz
Core stepping
R0
C1
EO
CPUID string
1067Ah
10676h
1067Ah
Thermal specification 71.4°C
71°C
71°C
Core voltage
1.3625V
0.962V-1.237V
1.3625V
Processor number
X3210
X3220
X3320
System specifications
85
Intel Core 2 Duo
Specification
Description
Processor number
E4400
CPU speed
2.0 GHz
Bus speed
800 MHz
Bus/core ratio
10
L2 cache size
2 MB
L2 cache speed
2.0 GHz
Core stepping
L2
CPUID string
06F2h
Thermal specification
61.4°C
Core voltage
1.162V–1.312V
Intel Celeron
Specification
Description
Processor number
L420
L440
CPU speed
1.6 GHz
2.0 GHz
Bus speed
800 MHz
800 MHz
Bus/core ratio
8
10
L2 cache size
512 KB
512 KB
L2 cache speed
1.6 GHz
2.0 GHz
Core stepping
A1
A1
CPUID string
10661h
10661h
Thermal specification
60.4°C
60.4°C
Core voltage
1.050V–1.300V
1.050V–1.300V
System specifications
86
SATA optical disc drives
Item
Description
Model
HLDS GDR-H20N
Drive type
5.25-inch, half-height, tray load DVD-ROM 5.25-inch, half-height, tray load DVD-RW
Supported disc formats Read and play
• CD-DA, CD-ROM, CD-ROM XA,
CD-Extra, CD-R, CD-RW, HS CD-RW,
US CD-RW, and US+ CD-RW
•
•
•
•
Video CD
CD-i
Photo CD
DVD-R, DVD+R, DVD-RW, DVD+RW,
DVD+R Double Layer, DVD-R Double
Layer, DVD-ROM, and DVD-Video
ROM
HLDS GSA-H60L
Read and play the same disc formats as
the GDR-H20N model.
Write to the following media:
• CD-R
• LS CD-RW, HS CD-RW, and US
CD-RW
• Photo CD
• DVD-R, DVD-RW, DVD-RAM, DVD+R,
and DVD+RW
Use LightScribe technology to print disc
labels on LightScribe-compliant:
• CD-R
• DVD-R and DVD+R
Supported writing
methods
n/a
• Disc at Once, Track at Once, and
Session at Once
• Restricted Overwrite
• Layer Jump
• Fixed Packet and Variable Packet
Read speed
16X
16X
Write speed
n/a
16X
Three-way eject
support
• Using software
• Using drive eject button
• Using emergency eject hole
• Using software
• Using drive eject button
• Using emergency eject hole
Height
42 mm (16.53 in.)
42 mm (16.53 in.)
Length
170 mm (6.69 in.)
170 mm (6.69 in.)
Width
148 mm (5.83 in.)
148 mm (5.83 in.)
Weight (typical)
0.66 kg (1.455 lb)
0.66 kg (1.455 lb)
Physical specifications
Operating conditions
Temperature
0–50°C (32–122°F)
0–50°C (32–122°F)
Humidity
(non-condensing)
10–90% RH
10–90% RH
NOTES:
• CD-i and Photo CD may require special reader/player software.
• Photo CD writing requires Kodak license.
• LightScribe printing requires LightScribe-supported applications and LightScribe-specific discs with a thin dye
coating.
System specifications
87
SAS hard drives
Item
Description
Model
Seagate Cheetah 15K.5
ST373455SS
Fujitsu MAX3 RC
MAX3073RC
Fujitsu MBA3 RC
MBA3073RC
Form factor
3.5-inch
3.5-inch
3.5-inch
Capacity
75,161 MB
75,264 MB
75,264 MB
Bytes per sector
512
512
512
Rotational speed
15,000 rpm
15,000 rpm
15,000 rpm
Cache
16 MB
16 MB
16 MB
Average latency
2 ms
2 ms
2 ms
Read
3.5 ms
3.3 ms
3.4 ms
Write
4.0 ms
3.8 ms
3.9 ms
3 Gb/s
3 Gb/s
3 Gb/s
Height
26.1 mm (1.028 in.)
25.4 mm (1.0 in.)
25.4 mm (1.0 in.)
Length
147 mm (5.787 in.)
146 mm (5.748 in.)
146 mm (5.748 in.)
Width
101.85 mm (4.010 in.)
101.6 mm (4.0 in.)
101.6 mm (4.0 in.)
Weight (typical)
0.839 kg (1.85 lb)
0.80 kg (1.764 lb)
0.80 kg (1.764 lb)
Temperature
5–55°C (41°–131°F)
5– 55°C (41–131°F)
5°–55°C (41–131°F)
Humidity
(non-condensing)
5–95% RH
5–95% RH
5–95% RH
Seek times (average)
Maximum transfer rate
(buffer to host)
Physical specifications
Operating conditions
System specifications
88
SATA hard drives
Item
Description
Model
WD Caviar SE WD1600JS
Seagate Barracuda
ST3160815AS
Form factor
3.5-inch
3.5-inch
Capacity
160,041 MB
160,041 MB
Used sectors per drive
312,581,808
312,581,808
Bytes per sector
512
512
Rotational speed
7,200 rpm
7,200 rpm
Cache
8 MB
8 MB
Average latency
4.20 ms
4.16 ms
Read
8.9 ms
<11.0 ms
Write
10.9 ms
<12.0 ms
Track to track
2.0 ms
<1.0 ms
Full-stroke
21 ms
—
3 Gb/s
3 Gb/s
Height
26.1 mm (1.028 in.)
19.99 mm (.787 in.)
Length
147 mm (5.787 in.)
147 mm (5.787 in.)
Width
101.6 mm (4.0 in.)
101.6 mm (4.0 in.)
Weight (typical)
0.60 kg (1.32 lb)
0.38 kg (.838 lb)
Temperature
5–55°C (41–131°F)
0–60°C (32–140°F)
Humidity (non-condensing)
5–95% RH
5–90% RH
Seek times (average)
Maximum transfer rate (buffer to host)
Physical specifications
Operating conditions
System specifications
89
SAS controller board
Item
Description
Model
LSI SAS SC40Ge PCI Express to 4-Port Serial Attached SCSI Controller
Form factor
Half-height, half length
Dimensions
Height
63.5 mm (2.5 in)
Depth
167.6 mm (6.6 in)
Interface type
PCI Express x8 line with x8 slot
Supported devices
Hard drive, disk array (RAID)
Controller interface
• SAS – 1.5 Gb/s and 3.0 Gb/s
• SATA – 1.5 Gb/s SATA
Data transfer rate
2 GB/s
Number of channels
One internal x4 SAS connector with four sideband lines
RAID support
• RAID 0 – minimum of two drives, maximum of four drives
• RAID 1 – two drives plus one spare
NOTE: SAS spare is associated with the SAS drive volume; SATA spare is
associated with the SATA drive volume.
OS support
•
•
•
•
Windows Server 2003
Linux Red Hat 4 and 5
SuSE Enterprise Edition Linux 10 update 1
Novell Netware 6.5 SP6
Operating conditions
Temperature
0–60°C (32–140°F)
Humidity (non-condensing)
5–90% RH
System specifications
90
Power supply unit
Item
Description
Model
PS-6361-4HF1-ROHS
Type
365W
Dimensions
Height
97.6 mm (3.8 in.)
Depth
153.7 mm (6.1 in.)
Width
150 mm (5.9 in.)
Weight (approximate)
1.73 kg (3.81 lb)
Input requirements
Rated input voltage
100–27 VAC, 200–240 VAC
Normal line voltage
115 VAC, 230 VAC
Line frequency
47–63 Hz
Rated input current
Load 6A at 100–240 VAC
Inrush current
40A2sec
Power supply output power
Rated steady state power
365W
Maximum peak power
385W
Operating conditions
Temperature
10–50°C (50–122°F)
Humidity (non-condensing)
5–95% at +40°C
System specifications
91
Software specifications
Item
Description
Network operating
•
system (NOS) support •
Microsoft Windows Server 2003 R2 Enterprise Edition
•
•
•
•
•
•
•
•
•
•
•
Microsoft Windows Server 2003 R2 Standard Edition
•
•
•
•
•
•
•
HP Insight Diagnostics
System diagnostics
Microsoft Windows Server 2003 R2 Enterprise x64 Edition
Microsoft Windows Server 2003 R2 Standard x64 Edition
Microsoft Windows Small Business Server 2003 R2
Microsoft Windows Server 2003 Web Edition
Red Hat Enterprise Linux 5 AS (x86)
Red Hat Enterprise Linux 5 AS [AMD64/EM64T]
Red Hat Enterprise Linux 4 AS (x86)
Red Hat Enterprise Linux 4 AS (AMD64/EM64T)
SUSE Linux Enterprise Server 10 (x86)
SUSE Linux Enterprise Server 10 (AMD64/EM64T)
Novell Netware 6.5
Survey Utility
Array Diagnostic Utility
HP Instant Support Enterprise Edition
Web-Based Enterprise Service
Open Services Event Manager
Phoenix BIOS Setup Utility
System specifications
92
Physical specifications
Item
System board platform
Description
uATX (Micro Advanced Technology Extended)
System board dimensions
Length
244 mm (9.6 in.)
Width
244 mm (9.6 in.)
Server dimensions
Height
367 mm (14.5 in.)
Width
175 mm (6.9 in.)
Depth
With bezel – 426 mm (16.8 in.)
Without bezel – 386 mm (15.2 in.)
Server weight (maximum configuration,
approximate)
Basic configuration (excluding the
keyboard and mouse)
10.9 kg (24.03 lb)
Fully loaded configuration (including
the keyboard, mouse, and kits)
12.9 kg (28.44 lb)
System specifications
93
Environmental specifications
Item
Description
Temperature range
Operating
10–40°C (50–104°F)
Non-operating
-35–65°C (-31–149°F)
Humidity (non-condensing)
Operating
10–90% RH
Non-operating
10–95% RH
Altitude
Operating
0–10,000 feet
Non-operating
0–30,000 feet
Acoustic noise
Idle, minimum (fixed disk drives
spinning)
L Wad (BELS) – 4.5
L pA (dBA) – 28
Operating, minimum (random
seeks to fixed disk drives)
L Wad (BELS) – 5.0
L pA (dBA) – 33
System specifications
94
Index
A D AC power
diagnostics
external LED indicator, 79
Array Diagnostic Utility, 61
power-down procedure, 29
HP Insight Diagnostics, 60
system board LED indicator, 80
Phoenix BIOS software, 61
access panel
part number, 17
Survey Utility, 60
drive bay configuration
removing, 31
data cable management, 34
hard drives, 38
B power cable connections, 35
Baseboard Management Controller. See BMC
removable media drives, 35
Basic Input/Output System. See Phoenix BIOS Setup Utility
battery
system drive bays, 33
location, 54
drive release latch, 17
replacement warnings, 55
E replacing, 55
electrostatic discharge. See ESD
BMC
embedded NIC port
specification, 81
LED indicators, 79
system board LED indicator, 80
location, 76
MAC address, 64
boot sequence
configuring, 67
environmental specifications
acoustic noise, 94
default settings, 67
altitude, 94
boot-time diagnostic screen
relative humidity, 94
information display, 68
temperature, 94
viewing, 68
ESCD
C clearing configuration data, 65
cable clamp, 17
cable management, 30
CMOS RAM
definition, 65
ESD
precautions, 28
clearing, 71
definition, 62
POST error messages, 73
work area recommendations, 28
expansion board
expansion slots, 49
resetting, 71
console redirection, 65
core logic chipset
installing, 49
Extended System Configuration Data. See ESCD
north bridge, 81
F south bridge, 81
front bezel
CSR, 5
customer self repair. See CSR
part number, 17
removing, 32
front panel, 75
full-length card retainer, 17
Index
95
illustrated parts catalog
G General Help window, 63
mechanical components, 16
H system components, 20
hard drive
IPMI card
installing, 51
configuring, 65
overview, 51
installing, 38
storage controller, 81
supported drives, 38
hardware configuration
part number, 22
Item Specific Help panel, 63
L boot-time diagnostic screen, 68
legend bar, 63
ESD damage prevention, 28
Lights-Out 100c management port
expansion board, 49
installation, 51
IPMI card, 51
LED indicators, 79
memory, 47
location, 76
Phoenix BIOS Setup Utility, 61
post-installation procedure, 29
power supply unit, 58
pre-installation procedure, 28
processor, 42
references, 26
M MAC address, 64
mechanical components, 16
Media Access Control. See MAC address
memory
DIMM part numbers, 22
symbols in equipment, 27
DIMM slots location, 47
system battery, 54
installation guidelines, 47
system drives, 33
installing, 47
system fans, 56
memory size value, 64
tools, 26
population sequence, 47
warnings/precautions, 26
HDD EMI shield
installing, 41
part number, 17
removing, 38
heat sink fan
cable connector, 77
installing, 46
part number, 21
specifications, 82
memory controller, 81
multi-boot support, 67
N network operating system. See NOS support
NOS support, 92
O onboard controllers
BMC, 81
precaution, 43
LAN, 81
removing, 43
memory controller, 81
HP
storage controller, 81
contact information, 25
VGA, 81
technical support, 25
P I I/O ports
front panel, 75
listing, 81
rear panel, 76
I/O subsystem, 81
PCI slot cover
removing, 49
PCI slot cover retainer
installing, 50
part number, 17
Index
96
removing, 49
part numbers, 21
Phoenix BIOS Setup Utility
removing, 44
”Run Setup” message, 62
socket location, 42
Advanced menu, 65
technical specifications, 82
Boot menu, 67
thermal compound, 44
Boot-time Diagnostic Screen, 68
PSU
clearing the CMOS RAM, 70
cable connections, 35
closing, 68
installing, 59
CMOS RAM, 62
part number, 22
General Help window, 63
removing, 58
Item Specific Help panel, 63
replacement warnings, 58
legend bar, 63, 64
specifications, 91
loading system defaults, 70
PXE, 67
Main menu, 64
R navigation keys, 63
non-user-configurable field, 63
overview, 61
rear panel, 76
recording Setup values
CMOS backup utility, 70
recording Setup values, 69
running, 62
Security menu, 66
manual record, 69
removable media drive
installing, 35
supervisor password, 66
part numbers, 21
updating the BIOS, 69
user-configurable field, 63
Phoenix BIOS software
supported drives, 35
removable media drive bay EMI shield
part number, 17
overview, 61
POST, 71
physical specifications
server, 93
system board, 93
POST
error indicators, 71
errors messages, 71
non-critical errors, 71
overview, 71
running, 71
troubleshooting, 74
power fluctuations, caution, 29
power supply unit. See PSU
power-down procedures, 29
Power-On Self-Test. See POST
Preboot Execution Environment. See PXE
processor
ATX power connector, 78
configuring, 65
installation guidelines, 42
installing, 45
removing, 37
S SAS controller board
installing, 49
part number, 22
specifications, 90
SAS hard drive
cable connections, 34
installing, 38
LED cable connector, 77
part numbers, 21
specifications, 88
SAS HDD cable
connection, 34
part number, 21
SAS LED cable
connection, 34
part number, 21
SATA data cable
connections, 34
part number, 21
Index
97
SATA hard drive
front panel, 75
cable connections, 34
rear panel, 76
data cable connectors, 77
system board, 77
installing, 38
system covers
part numbers, 21
access panel, 31
specifications, 89
front bezel, 32
server management
system date
configuring, 65
POST error message, 73
specification, 82
setting, 64
status LED indicators, 79
system fan
software specifications
cable connector, 78
NOS, 92
part number, 22
system diagnostics, 92
replacement warning, 56
spare parts
mechanical components, 16
replacing, 56
system time
storing, 28
POST error message, 73
system components, 20
setting, 64
transporting, 28
standby mode
activating, 29
T technical specifications
environmental, 94
effects, 29
hardware, 81
external LED indicator, 79
memory, 82
system board LED indicator, 80
physical, 93
status LED indicators
power supply unit, 91
hard drive activity, 79
processor, 82
LAN activity, 79
SAS controller board, 90
LAN network speed, 79
SAS hard drive, 88
optical drive activity, 79
SATA CD-ROM drive, 87
power, 79
SATA hard drive, 89
system board, 80
supervisor password
changing, 66
removing, 67
resetting, 67
setting, 66
software, 92
thermal compound, 44
thermal solution, 82
U uATX
Micro Advanced Technology Extended. See system
board, platform
system board
ATX power connector, 78
dimensions, 93
layout, 77
part numbers, 22
platform, 93
status LED indicators, 80
system components, 20
uninterruptible power supply. See UPS
UPS, 29
V VGA controller, 81
W warranty, 5
Index
98