advertisement
W32CO Mantel and Base
ASSEMBLY AND INSTALLATION INSTRUCTIONS
IMPORTANT: Read entire instruction sheet before assembling or installing mantel kit.
These mantels are only approved for use with any FMI PRODUCTS, LLC 32'' electric and gas fireplace systems. Do not use mantel with any other product.
• This mantel kit contains the following:
#1 Base
#2 Right Side Assembly
#3 Left Side Assembly
#4 Header
#5 Top
• Hardware Package
22 - 1 1/4" Wood Screws 114325-01
* Extra hardware may be included
Tools required:
• Power Screwdriver with #2 Phillips Bit
If any wood pieces are missing or damaged, contact the dealer where you purchased this mantel for replacement. If hardware is missing or damaged, contact FMI PRODUCTS, LLC at
1-866-328-4537 for referral information. You can also visit
FMI PRODUCTS, LLC’s web site at www.fmiproducts.com.
Note: Gather all mantel pieces together before assembling mantel.
WARNING: Only use 1 1/4" screws to assemble mantel. Damage to mantel will result if other screws are used for this purpose.
For more information, visit www.fmiproducts.com
ASSEMBLING MANTEL
IMPORTANT: More than one person is required to lift assembled mantel. Lift mantel by leg assemblies. Lifting by header or mantel top could damage mantel.
Use the following illustrations to assemble mantel. Use only screws provided.
Right Leg
Assembly
#2
Header #4
Right Leg
Assembly #2
Header into
Groove on
Legs
1¼'' Screws
Left Leg
Assembly #3
Header
Assembly
Block
1¼'' Screws
Left Leg
Assembly #3
Figure 1 - Installing Header
Mantel Top #5
Base #1
Flush
Figure 3 - Installing Mantel Base
IMPORTANT: Align mantel left to right on base before installing.
Mantel legs must be flush with back of mantel base before installation. Use a tape measure to insure accuracy.
Header
Assembly
Block
1¼'' Screws
Figure 2 - Installing Top
IMPORTANT: Align mantel top left to right before installing.
Back corner of mantel leg must be flush with edge of mantel top before installation.
2 www.fmiproducts.com
123677-01B
GAS FIREPLACE INSTALLATION
1. Fireplace should be fully assembled. See Assembling
Fireplace in fireplace owner’s manual.
2. Mantel must be installed flush with two walls. Remove baseboard along walls where mantel is to be installed.
Baseboard will prevent proper installation of mantel and base.
3. Place mantel base close to installation location. See fireplace owner’s manual for installation clearances. Leave enough room to insert fireplace from back of mantel.
4. If installing gas fireplace, install gas line. See Connecting
to Gas Supply in fireplace owner’s manual. Remember to leave access to gas shutoff valve somewhere on mantel base or where it is accessible to user. Check for leaks.
See Checking Gas Connections in fireplace owner’s manual.
5. Position fireplace inside mantel through back opening
(see Figure 6). Carefully position gas lines if applicable.
IMPORTANT: Use caution when positioning fireplace on base. Base may scratch easily. Make sure fireplace is in proper position within mantel opening before continuing with installation.
6. Fireplace with louver door: Lower bottom louver door.
Use two screws provided in fireplace hardware kit and attach fireplace to wooden base. Close louver door.
Gas
fireplace with fixed louver: Before installing logs or burner assembly (see owner’s manual) remove screws securing floor to assembly. Lift floor for access to bottom of fireplace. Use two screws provided in fireplace hardware kit and attach fireplace base to wooden base.
Reinstall floor with screws removed previously.
7. Carefully push mantel and base into position against wall.
ELECTRIC FIREPLACE INSTALLATION
This mantel can be used with FMI PRODUCTS, LLC electric fireplaces. Electric fireplaces install from the front of mantel.
To install electric fireplace see fireplace instruction manual.
123677-01B
Figure 4 - Installing Gas Fireplace www.fmiproducts.com
3
2701 S. Harbor Blvd.
Santa Ana, CA 92704
1-866-328-4537 www.fmiproducts.com
123677-01
Rev. B
09/11
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement