Extron electronics MTP U T A D User guide

User Guide
Twisted Pair
MTP U T A D
Universal Decora MTP Transmitter
68-1674-01 Rev. C
04 11
Safety Instructions • English
I
D
Power sources • This equipment should be operated only from the power source indicated on the product. This
equipment is intended to be used with a main power system with a grounded (neutral) conductor. The third
(grounding) pin is a safety feature, do not attempt to bypass or disable it.
This symbol is intended to alert the user of the presence of uninsulated
dangerous voltage within the product’s enclosure that may present a risk of
electric shock.
Power disconnection • To remove power from the equipment safely, remove all power cords from the rear of
the equipment, or the desktop power module (if detachable), or from the power source receptacle (wall plug).
Caution
Read Instructions • Read and understand all safety and operating instructions before using the equipment.
Retain Instructions • The safety instructions should be kept for future reference.
Follow Warnings • Follow all warnings and instructions marked on the equipment or in the user information.
Avoid Attachments • Do not use tools or attachments that are not recommended by the equipment
manufacturer because they may be hazardous.
Consignes de Sécurité • Français
I
D
Ce symbole sert à avertir l’utilisateur que la documentation fournie avec le
matériel contient des instructions importantes concernant l’exploitation et la
maintenance (réparation).
Ce symbole sert à avertir l’utilisateur de la présence dans le boîtier
de l’appareil de  tensions dangereuses non isolées posant des risques
d’électrocution.
Attention
Lire les instructions• Prendre connaissance de toutes les consignes de sécurité et d’exploitation avant
d’utiliser le matériel.
Conserver les instructions• Ranger les consignes de sécurité afin de pouvoir les consulter à l’avenir.
Respecter les avertissements • Observer tous les avertissements et consignes marqués sur le matériel ou
présentés dans la documentation utilisateur.
Eviter les pièces de fixation • Ne pas utiliser de pièces de fixation ni d’outils non recommandés par le
fabricant du matériel car cela risquerait de poser certains dangers.
Sicherheitsanleitungen • Deutsch
I
D
Servicing • Refer all servicing to qualified service personnel. There are no user-serviceable parts inside. To prevent
the risk of shock, do not attempt to service this equipment yourself because opening or removing covers may
expose you to dangerous voltage or other hazards.
Slots and openings • If the equipment has slots or holes in the enclosure, these are provided to prevent
overheating of sensitive components inside. These openings must never be blocked by other objects.
Lithium battery • There is a danger of explosion if battery is incorrectly replaced. Replace it only with the
same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the
manufacturer’s instructions.
Avertissement
Alimentations • Ne faire fonctionner ce matériel qu’avec la source d’alimentation indiquée sur l’appareil. Ce
matériel doit être utilisé avec une alimentation principale comportant un fil de terre (neutre). Le troisième
contact (de mise à la terre) constitue un dispositif de sécurité : n’essayez pas de la contourner ni de la
désactiver.
Déconnexion de l’alimentation• Pour mettre le matériel hors tension sans danger, déconnectez tous les
cordons d’alimentation de l’arrière de l’appareil ou du module d’alimentation de bureau (s’il est amovible) ou
encore de la prise secteur.
Protection du cordon d’alimentation • Acheminer les cordons d’alimentation de manière à ce que personne
ne risque de marcher dessus et à ce qu’ils ne soient pas écrasés ou pincés par des objets.
Réparation-maintenance • Faire exécuter toutes les interventions de réparation-maintenance par un
technicien qualifié. Aucun des éléments internes ne peut être réparé par l’utilisateur. Afin d’éviter tout danger
d’électrocution, l’utilisateur ne doit pas essayer de procéder lui-même à ces opérations car l’ouverture ou le
retrait des couvercles risquent de l’exposer à de hautes tensions et autres dangers.
Fentes et orifices • Si le boîtier de l’appareil comporte des fentes ou des orifices, ceux-ci servent à empêcher les
composants internes sensibles de surchauffer. Ces ouvertures ne doivent jamais être bloquées par des objets.
Lithium Batterie • Il a danger d’explosion s’ll y a remplacment incorrect de la batterie. Remplacer uniquement
avec une batterie du meme type ou d’un ype equivalent recommande par le constructeur. Mettre au reut les
batteries usagees conformement aux instructions du fabricant.
Vorsicht
Stromquellen • Dieses Gerät sollte nur über die auf dem Produkt angegebene Stromquelle betrieben werden.
Dieses Gerät wurde für eine Verwendung mit einer Hauptstromleitung mit einem geerdeten (neutralen) Leiter
konzipiert. Der dritte Kontakt ist für einen Erdanschluß, und stellt eine Sicherheitsfunktion dar. Diese sollte nicht
umgangen oder außer Betrieb gesetzt werden.
Dieses Symbol soll den Benutzer darauf aufmerksam machen, daß im Inneren
des Gehäuses dieses Produktes gefährliche Spannungen, die nicht isoliert sind
und die einen elektrischen Schock verursachen können, herrschen.
Stromunterbrechung • Um das Gerät auf sichere Weise vom Netz zu trennen, sollten Sie alle Netzkabel aus der
Rückseite des Gerätes, aus der externen Stomversorgung (falls dies möglich ist) oder aus der Wandsteckdose
ziehen.
Lesen der Anleitungen • Bevor Sie das Gerät zum ersten Mal verwenden, sollten Sie alle Sicherheits-und
Bedienungsanleitungen genau durchlesen und verstehen.
Aufbewahren der Anleitungen • Die Hinweise zur elektrischen Sicherheit des Produktes sollten Sie
aufbewahren, damit Sie im Bedarfsfall darauf zurückgreifen können.
Befolgen der Warnhinweise • Befolgen Sie alle Warnhinweise und Anleitungen auf dem Gerät oder in der
Benutzerdokumentation.
Keine Zusatzgeräte • Verwenden Sie keine Werkzeuge oder Zusatzgeräte, die nicht ausdrücklich vom
Hersteller empfohlen wurden, da diese eine Gefahrenquelle darstellen können.
Instrucciones de seguridad • Español
Este símbolo se utiliza para advertir al usuario sobre instrucciones importantes de operación y mantenimiento (o cambio de partes) que se desean
destacar en el contenido de la documentación suministrada con los equipos.
Este símbolo se utiliza para advertir al usuario sobre la presencia de elementos con voltaje peligroso sin protección aislante, que puedan encontrarse
dentro de la caja o alojamiento del producto, y que puedan representar
riesgo de electrocución.
Precaucion
Leer las instrucciones • Leer y analizar todas las instrucciones de operación y seguridad, antes de usar el
equipo.
Conservar las instrucciones • Conservar las instrucciones de seguridad para futura consulta.
Obedecer las advertencias • Todas las advertencias e instrucciones marcadas en el equipo o en la
documentación del usuario, deben ser obedecidas.
Evitar el uso de accesorios • No usar herramientas o accesorios que no sean especificamente
recomendados por el fabricante, ya que podrian implicar riesgos.
安全须知 • 中文
I
D
Power cord protection • Power cords should be routed so that they are not likely to be stepped on or pinched
by items placed upon or against them.
Dieses Symbol soll dem Benutzer in der im Lieferumfang enthaltenen
Dokumentation besonders wichtige Hinweise zur Bedienung und Wartung
(Instandhaltung) geben.
Achtung
I
D
Warning
This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment.
这个符号提示用户该设备用户手册中有重要的操作和维护说明。
这个符号警告用户该设备机壳内有暴露的危险电压,有触电危险。
注意
阅读说明书
保存说明书
遵守警告 •
避免追加 •
• 用户使用该设备前必须阅读并理解所有安全和使用说明。
• 用 户应保存安全说明书以备将来使用。
用户应遵守产品和用户指南上的所有安全和操作说明。
不要使用该产品厂商没有推荐的工具或追加设备,以避免危险。
Schutz des Netzkabels • Netzkabel sollten stets so verlegt werden, daß sie nicht im Weg liegen und niemand
darauf treten kann oder Objekte darauf- oder unmittelbar dagegengestellt werden können.
Wartung • Alle Wartungsmaßnahmen sollten nur von qualifiziertem Servicepersonal durchgeführt werden.
Die internen Komponenten des Gerätes sind wartungsfrei. Zur Vermeidung eines elektrischen Schocks
versuchen Sie in keinem Fall, dieses Gerät selbst öffnen, da beim Entfernen der Abdeckungen die Gefahr eines
elektrischen Schlags und/oder andere Gefahren bestehen.
Schlitze und Öffnungen • Wenn das Gerät Schlitze oder Löcher im Gehäuse aufweist, dienen diese zur
Vermeidung einer Überhitzung der empfindlichen Teile im Inneren. Diese Öffnungen dürfen niemals von
anderen Objekten blockiert werden.
Litium-Batterie • Explosionsgefahr, falls die Batterie nicht richtig ersetzt wird. Ersetzen Sie verbrauchte Batterien
nur durch den gleichen oder einen vergleichbaren Batterietyp, der auch vom Hersteller empfohlen wird.
Entsorgen Sie verbrauchte Batterien bitte gemäß den Herstelleranweisungen.
Advertencia
Alimentación eléctrica • Este equipo debe conectarse únicamente a la fuente/tipo de alimentación eléctrica
indicada en el mismo. La alimentación eléctrica de este equipo debe provenir de un sistema de distribución
general con conductor neutro a tierra. La tercera pata (puesta a tierra) es una medida de seguridad, no
puentearia ni eliminaria.
Desconexión de alimentación eléctrica • Para desconectar con seguridad la acometida de alimentación
eléctrica al equipo, desenchufar todos los cables de alimentación en el panel trasero del equipo, o desenchufar
el módulo de alimentación (si fuera independiente), o desenchufar el cable del receptáculo de la pared.
Protección del cables de alimentación • Los cables de alimentación eléctrica se deben instalar en lugares
donde no sean pisados ni apretados por objetos que se puedan apoyar sobre ellos.
Reparaciones/mantenimiento • Solicitar siempre los servicios técnicos de personal calificado. En el interior no
hay partes a las que el usuario deba acceder. Para evitar riesgo de electrocución, no intentar personalmente la
reparación/mantenimiento de este equipo, ya que al abrir o extraer las tapas puede quedar expuesto a voltajes
peligrosos u otros riesgos.
Ranuras y aberturas • Si el equipo posee ranuras o orificios en su caja/alojamiento, es para evitar el
sobrecalientamiento de componentes internos sensibles. Estas aberturas nunca se deben obstruir con otros
objetos.
Batería de litio • Existe riesgo de explosión si esta batería se coloca en la posición incorrecta. Cambiar esta
batería únicamente con el mismo tipo (o su equivalente) recomendado por el fabricante. Desachar las baterías
usadas siguiendo las instrucciones del fabricante.
警告
电源 • 该设备只能使用产品上标明的电源。 设备必须使用有地线的供电系统供电。 第三条线(
地线)是安全设施,不能不用或跳过 。
拔掉电源 • 为安全地从设备拔掉电源,请拔掉所有设备后或桌面电源的电源线,或任何接到市电
系统的电源线。
电源线保护 • 妥善布线, 避免被踩踏,或重物挤压。
维护 • 所有维修必须由认证的维修人员进行。 设备内部没有用户可以更换的零件。为避免出现触
电危险不要自己试图打开设备盖子维修该设备。
通风孔 • 有些设备机壳上有通风槽或孔,它们是用来防止机内敏感元件过热。 不要用任何东西
挡住通风孔。
锂电池 • 不正确的更换电池会有爆炸的危险。必须使用与厂家推荐的相同或相近型号的电池。按
ii
照生产厂的建议处理废弃电池。
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15
of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
The Class A limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the
user will be required to correct the interference at his own expense.
NOTE: This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used with
the unit to ensure compliance with FCC emissions limits.
For more information on safety guidelines, regulatory compliances, EMI/EMF compliance, accessibility, and
related topics, click here.
iii
Conventions Used in this Guide
In this user guide, the following are used:
NOTE: A note draws attention to important information.
TIP: A tip provides a suggestion to make working with the application easier.
CAUTION: A caution indicates a potential hazard to equipment or data.
WARNING: A warning warns of things or actions that might cause injury, death, or
other severe consequences.
Commands are written in the fonts shown here:
^AR Merge Scene,,Op1 scene 1,1 ^B 51 ^W^C
[01] R 0004 00300 00400 00800 00600 [02] 35 [17] [03]
E X! *X1&* X2)* X2#* X2! CE}
NOTE: For commands and examples of computer or device responses mentioned in
this guide, the character “0” is used for the number zero and “O” represents the capital letter “o.”
Computer responses and directory paths that do not have variables are written in the font
shown here:
Reply from 208.132.180.48: bytes=32 times=2ms TTL=32
C:\Program Files\Extron
Variables are written in slanted form as shown here:
ping xxx.xxx.xxx.xxx —t
SOH R Data STX Command ETB ETX
Selectable items, such as menu names, menu options, buttons, tabs, and field names are
written in the font shown here:
From the File menu, select New.
Click the OK button.
Copyright
© 2011 Extron Electronics. All rights reserved.
Trademarks
All trademarks mentioned in this guide are the properties of their respective owners.
iv
Contents
Introduction............................................................ 1
About the Universal MTP Decora® Transmitter...... 1
Twisted Pair Cable................................................ 2
Transmission Distance..................................... 2
Installation and Operation.................................. 4
Installation........................................................... 4
UL Safety Requirements.................................. 4
Preparing the Site and Installing the
Wall Box........................................................ 5
Final Installation.............................................. 7
Connections and Settings.................................... 7
Front Panel Features........................................ 7
Video Connections......................................... 8
Audio Connections......................................... 8
Rear Panel Features....................................... 10
Making Connections.......................................... 11
Power Supply Wiring.................................... 11
TP Cable Termination.................................... 12
Receiver Considerations..................................... 12
Skew Delay Compensation................................ 13
Reference Information........................................ 14
Specifications..................................................... 14
Part Numbers..................................................... 16
MTP Transmitter and Compatible Devices...... 16
Included Parts............................................... 16
Cables.......................................................... 16
Connectors................................................... 17
Decora Template Dimensions............................. 17
Extron® Warranty................................................ 18
Contact Information............................................ 18
MTP U T A D User Guide • Contents
v
MTP U T A D User Guide • Contents
vi
Introduction
This section provides information on:
•
About the Universal MTP Decora® Transmitter
•
Twisted Pair Cable
About the Universal MTP Decora® Transmitter
The Extron MTP U T A D is a mini twisted pair (MTP) transmitter, in a two-gang Decora form
factor, that is fully compatible with all MTP video and audio receivers and associated MTP
products.
MTPs transmit and receive over Extron Enhanced Skew-Free A/V UTP cable or over CAT 5,
5e, or 6 shielded twisted pair (STP), unshielded twisted pair (UTP), or foil shielded twisted
pair (FTP) cable.
The Extron MTP U T A D transmitter and one or more compatible receivers comprise a
system for long-distance distribution of VGA or other high resolution and low resolution
video and audio.
The MTP transmitter inputs high or low resolution video signals (RGB, tri-level and bi-level
component video, S-video, or composite video) on connectors dedicated to each video
format. The transmitter can auto switch among the inputs or you can manually select the
input.
A buffered local monitor connector provides for pass-through of the RGB connector input.
The transmitter also inputs stereo audio signals on a 3.5 mm mini jack and RCA connectors.
The transmitter sums the left and right audio channels to convert the audio to mono (L+R)
format.
The transmitter converts the inputs to a proprietary signal and outputs that signal on an
RJ-45 connector.
The transmitter has dedicated connectors for RGB video, component video, S-video, and
composite video.
The compatible MTP receiver inputs the transmitted proprietary signal on an RJ-45
connector, converts the video back into its original format and resolution and the audio into
a dual mono output. The receiver 5 outputs video and audio locally.
The transmitter is shipped with an external 12 V, 1 A power supply that accepts 100 to
240 VAC, 50 Hz or 60 Hz input and provides worldwide power compatibility.
MTP U T A D • Introduction
1
Twisted Pair Cable
Twisted pair (TP) cable is much smaller, lighter, more flexible, and less expensive than coaxial
cable. These TP products make cable runs simpler and less cumbersome. Termination of the
cable with RJ-45 connectors is simple, quick, and economical.
Transmission Distance
NOTE: This transmitter provides pre-peaking, which boosts the signal before it is
transmitted.
The maximum distance is determined by the frequency and resolution of the signal that is
input to the transmitter. The table on the next page specifies the recommended maximum
transmission distances and transmitter Pre-Peak switch positions (refer to the applicable
transmitter guide) using Extron Enhanced Skew-Free A/V UTP cable or UTP CAT 5, 5e, or
6 cable, terminated with RJ-45 connectors.
NOTES: • It is possible to exceed the recommended distance; however, image quality
may be reduced.
• The MTP units are designed for and perform best with Extron Enhanced
Skew-Free A/V cable terminated in accordance with the TIA/EIA T 568 A wiring
standard. CAT 5, 5e, and 6 cables are acceptable, but less preferable. We also
recommend the use of preterminated and tested cables. Cables terminated on
site should be tested before use to ensure that they comply with Category 5
specifications.
MTP U T A D • Introduction
2
Recommended transmission distances at 60 Hz
Video Format
Pre-peak
OFF
Pre-peak
On
Composite,
S‑video,
Component
Max. Distance
(high quality)
Max. Distance
(variable quality)
800 ft
(245 m)
1000 ft
(300 m)
640 x 480
<300 ft
(90 m)
>350 ft
(105 m)
700 ft
(215 m)
750 ft
(200 m)
800 x 600
<300 ft
(90 m)
>350 ft
(105 m)
550 ft
(165 m)
650 ft
(200 m)
1024 x 768*
<300 ft
(90 m)
>350 ft
(105 m)
500 ft
(150 m)
600 ft
(185 m)
1280 x 960*
<300 ft
(90 m)
>350 ft
(105 m)
400 ft
(120 m)
500 ft
(150 m)
1280 x 1024*
<250 ft
(75 m)
>300 ft
(90 m)
350 ft
(105 m)
450 ft
(135 m)
1360 x 765
<250 ft
(75 m)
>300 ft
(90 m)
400 ft
(120 m)
500 ft
(150 m)
1365 x 768
<250 ft
(75 m)
>300 ft
(90 m)
400 ft
(120 m)
450 ft
(135 m)
1366 x 768
<250 ft
(75 m)
>300 ft
(90 m)
400 ft
(120 m)
450 ft
(135 m)
1400 x 1050
<250 ft
(75 m)
>300 ft
(90 m)
350 ft
(105 m)
400 ft
(120 m)
1440 x 900
<250 ft
(75 m)
>300 ft
(90 m)
350 ft
(105 m)
400 ft
(120 m)
1600 x 1200*
<250 ft
(75 m)
>300 ft
(90 m)
300 ft
(90 m)
450 ft
(135 m)
1920 x 1200
<250 ft
(75 m)
>300 ft
(90 m)
300 ft
(90 m)
400 ft
(120 m)
HDTV 720p
<250 ft
(75 m)
>300 ft
(90 m)
400 ft
(120 m)
500 ft
(150 m)
HDTV 1080i
<250 ft
(75 m)
>300 ft
(90 m)
300 ft
(90 m)
400 ft
(120 m)
HDTV 1080p
<250 ft
(75 m)
>300 ft
(90 m)
300 ft
(90 m)
400 ft
(120 m)
NOTES: • Resolutions marked with an asterisk (*) in this table have the same range
specifications at 75 Hz.
• Extron recommends using at least 25 feet (7.6 m) of TP cable between the
transmitter and the first receiver.
MTP U T A D • Introduction
3
Installation and
Operation
This section discusses the installation and operation of an MTP U T A D transmitter,
including:
•
Installation
•
Connections and Settings
•
Making Connections
•
Receiver Considerations
•
Skew Delay Compensation
Installation
The MTP U T A D transmitter can be installed in a two-gang electrical wall box with a Decora
wall plate cover (supplied).
The installation must conform to national and local electrical codes and to the wall plate size
requirements.
UL Safety Requirements
The following Underwriters Laboratories (UL) requirements pertain to the installation of the
Decora transmitter into a wall or furniture.
•
This unit must not be connected to a centralized DC power source or used beyond its
rated voltage range.
•
This unit must be installed in a UL listed junction box.
•
This unit must be installed with conduit in accordance with National Electrical Code.
MTP U T A D • Installation and Operation
4
Preparing the Site and Installing the Wall Box
Choose a location that allows cable runs without interference. Allow enough depth for
both the wall box and the cables. The box should be at least 2.5 inches (6.4 cm) deep
to accommodate the connectors and cables. Install the cables into the wall, furniture, or
conduits before installing the wall plate.
NOTE: The Decora unit is 1-5/16 inch (33 m) deep and has connectors on the
back side (see figure 1). Extron recommends its 2-gang junction box
(part number 980084), which has a depth of 2.5 inches (6.4 cm).
2 12" (63.5 mm)
RJ-45
Connector
Captive
Screw
Connectors
Junction Box
5
1 16
" (33.3 mm)
Figure 1. Decora Unit Depth Profile
If installing a new wall box, perform steps 1 through 12. If a suitable wall box is already
installed, perform steps 6 through 12. A UL listed wall box is recommended.
1. If a wall box is not available to use for a template, figure 9 on page 16 provides the
dimensions to create a template. If installing directly into furniture, cut out the center
portion of your template.
NOTE:The figure 9 illustration on page 16 is neither full size nor is it to scale. Do
not scale up or print to use as a template.
2. Place the wall box (or your template) against the installation surface and mark the
opening guidelines.
3. Cut out the material from the marked area.
4. Insert the wall box into the opening. The box or the rear connectors of the wall plate
should fit easily into the opening. Enlarge or smooth the edges of the opening if
needed.
MTP U T A D • Installation and Operation
5
5. Secure the wall box with nails or screws, leaving the front edge flush with the outer wall
or furniture surface (see figure 2).
Wall Stud
Wall Stud
Wall Box
Screws or
Nails
Cable
Clamp
Installation
Cable
Screws or
Nails
Figure 2.
Flush with
Wall Surface
Installing the Wall Box
NOTE: If attaching the wall box to
• Wood — use four #8 or #10 screws or 10-penny nails. A minimum of 0.5
inch (1.3 cm) of screw thread must penetrate the wood.
• Metal studs or furniture — use four #8 or #10 self-tapping sheet metal
screws or machine bolts with matching nuts.
6. Feed the power cable through the opening and through the wall box punch-out holes
into the box, securing the cable with cable clamps to provide strain relief.
NOTE: In order to fit in the junction box, the TP cable and RJ-45 connector should
not have a boot installed.
7. Feed the twisted pair cable in through the wall box punch-out holes, securing the cable
with clamps to provide strain relief.
8. Trim back or insulate exposed cable shields with heat shrink to reduce the chance of
short circuits.
9. To prevent short circuits, the outer foil shield can be cut back to the point where the
cable exits the cable clamp.
10.Connect the power cable and TP cable to the rear of the unit (see "Rear Panel
Features" for connector wiring details).
11.Connect a video and an audio source to the front panel (see "Front Panel Features"
for connector details).
12.Restore the power supply and test the transmitter/receiver system. Make any cabling
adjustments before final installation, as the cables will be inaccessible afterwards.
MTP U T A D • Installation and Operation
6
Final Installation
After testing and making any adjustments, do the following:
1. At the power outlet, unplug the power supply.
2. Mount the transmitter into the box and attach the supplied Decora faceplate to the unit
(see figure 3).
Wall Stud
Wall opening
is flush with
edge of box.
Cable Clamp
V
O
SWITCH MODE
PRE-PEAK
REFRESH 50/60Hz
O
DI
2
T
R
TE
CO
3
0
89A B
F 123
T
ITOR
67 O
DI
L
45
PU
IN
MPU
C
DD L.
SO
RE
AU
C
V Y
YU
B
T
PU
IN
AU
ON
1
Installation
Cable
RG
YU
C
Y/
VID
R
PW
TS O
PUS-VIDE
IN
VIDE
OU
MON
DE
Pb
R
Pr
MTP U T A D
Transmitter
Figure 3.
Decora
Faceplate
Mounting the Transmitter
3. At the power outlet, reconnect the power supply.
Connections and Settings
Front Panel Features
4
8
INPUTS
5
YUV
PWR VID S-VIDYUV PC
S-VIDEO
CONTACT
PRE-PEAK
50 Hz REFRESH
VIDEO
Y
10
AUDIO INPUT
7
ON
Pb
AUDIO
L
3456
0
R
2 3
9A
78
Pr
1
D
BC
6
1
EDID
SELECT
1
EF 2
3
COMPUTER INPUT
MONITOR OUT
2
9
Figure 4. Transmitter Front Panel Features
MTP U T A D • Installation and Operation
7
Video Connections
a Computer Input connector — Connect a computer (VGA) video source to this 15-pin
HD connector for a high resolution video input.
NOTES: • Input only sync signals, no video signals, on the sync pins (13 and 14).
• For component video, use the R (R-Y) and R return pins (pins 1 and 6),
G (Y) and G return pins (pins 2 and 7), and B (B-Y) and B return pins (pins
3 and 8).
• For S-video, use the R, R return (C-chroma), G, and G return (Y-luma) pins.
• For composite video, use the G pin and the associated return pin. For
additional genlocked video signals, use the R, B, and associated return
pins.
b Monitor Output connector — Connect a video monitor to this 15-pin HD connector
for buffered loop-through of the high or low resolution video input on the Computer
Input connector (a) only.
c YUV (component video) input connectors — Connect a component video source to
these RCA jacks for a high or low resolution component video input.
d S-video input connector — Connect an S-video source to this 4-pin mini-DIN
connector for a Y/C video input.
e Video (composite) input connector — Connect a composite video source to this RCA
jack for a low resolution video input.
Audio Connections
NOTES: • The Audio Input (mini-jack) audio connector is selected when:
• The Computer Input video (a) is selected for output.
• The transmitter is in auto switch mode (DIP switch 1 [h] is off) and no
active video signal is selected.
• The Audio (RCA) connectors are selected when:
• The YUV (c), S-video (d), or Video (composite) (e) input is selected.
• The selected stereo audio input is summed and output on the TP cable as
mono audio.
f Audio (RCA) connector — Plug stereo audio into these left and right RCA jacks for
unbalanced audio input. Wire the plug as shown in figure 5.
Tip
Left (+)
Ring
Right (-)
Tip (+)
Sleeve ( )
Sleeve ( )
RCA Connector
Figure 5.
3.5 mm Stereo Plug Connector
(balanced)
Typical Audio Plugs
g Audio Input (mini-jack) connector — Plug a 3.5 mm stereo audio plug into this jack
for unbalanced audio input. Wire the plug as shown in figure 5.
NOTE: Figure 5 shows a typical 3.5 mm audio connector, which consists of a tip,
ring, and sleeve, and an RCA connector, which consists of a tip and sleeve.
MTP U T A D • Installation and Operation
8
Configuration switches
The configuration switches (h and i) will be inaccessible once the Decora faceplate is
installed.
h DIP switches
•
Contact (1) — Set this switch on (up) for contact closure control of the input
selection. Set this switch off (down) to put the transmitter in auto switch mode (the
transmitter automatically selects the highest format video input with a sync signal
present).
•
Pre-Peak (2) — Set this switch on (up) to alter the TP signal output to compensate
for long cable runs. Set this switch off (down) for an unpeaked TP output. See
the table on page 4 for suggested switch settings based on the transmitted video
format and transmission distance.
•
50 Hz Refresh (3) — Set this switch on (up) for 50 Hz refresh rate for the resolution
selected by the EDID Select switch. Set this switch off (down) for 60 Hz.
i EDID Select rotary switch — Set this switch to one of the positions below to select
the local monitor as the source of the EDID data or a specific resolution.
•
Position 0 — The loop-through monitor (b, on page 6) is the source of the EDID
data.
•
Position 1 - F — Specify a resolution. The following table identifies the switch
positions and the associated resolutions. By default, the vertical refresh rate for
all resolutions is 60 Hz. The resolution can be set to 50 Hz using the Refresh DIP
switch (h).
Pos.
Source or
Resolution
Pos.
Resolution
Pos.
Resolution
0
Local monitor
6
1280 x 1024
C
1680 x 1050
1
800 x 600
7
1360 x 768
D
1920 x 1080
2
1024 x 768
8
1366 x 768
E
1920 x 1200
3
1280 x 720
9
1400 x 1050
F
Not used
4
1280 x 768
A
1440 x 900
5
1280 x 800
B
1600 x 1200
Status LEDs
j LEDs —
•
Power — This LED indicates power is applied to the MTP.
•
Active input — The lit LED (PC, YUV, S-VID, or VID) indicates the video input that is
selected for output on the TP connector.
NOTE: When an input selection is made in contact closure mode, and no signal
is active on the input, the selected LED blinks.
MTP U T A D • Installation and Operation
9
Rear Panel Features
11
OUTPUT
12 V
1
Figure 6.
2
3
4
_
+
.5A
MAX
12
13
Transmitter Rear Panel Features
k Output connector — Connect a TP cable from this RJ-45 female connector to the
compatible receiver (see “TP Cable Termination” to wire the RJ-45 connectors).
NOTE: See the table on page 3 for recommended transmission ranges.
l Contact closure controls — To select a video input to output, momentarily tie the
assigned pin for that format to ground.
Pin
Format
Pin
Format
Pin
Ground
1
Composite
3
YUV
5
Ground
2
S-video
4
PC
NOTE: The front panel Contact DIP switch (h) must be on (up) for contact closure
to be available.
m DC power connector — Plug the external 12 VDC, 1 A power supply into this 2-pole
captive screw connector (see "Power Supply Wiring" to wire the connectors).
NOTE: The remote power capabilities available with certain MTP models are not
supported by this unit; the transmitter and receiver both must be powered.
MTP U T A D • Installation and Operation
10
Making Connections
Power Supply Wiring
Figure 7 shows how to wire the power connector.
12 V
Tie Wrap
SECTION A–A
3/16”
(5 mm) Max.
Smooth
Ridges
A
A
2-Pole
Captive Screw
Connector (12V)
Figure 7. Power Connector Wiring
CAUTION: Power supply voltage polarity is critical. Incorrect voltage polarity can
damage the power supply and the MTP. Identify the power cord negative
lead by the ridges on the side of the cord (see figure 7).
To verify the polarity before connection, plug in the power supply with no load and check
the output with a voltmeter.
WARNING: The two power cord wires must be kept separate while the power supply is
plugged in. Remove power before wiring.
CAUTION:
The length of the exposed (stripped) copper wires is important. The ideal
length is 3/16 inch (5 mm). Longer bare wires can short together. Shorter
wires are not as secure in the direct insertion connectors and could be
pulled out.
NOTE: Do not tin the power supply leads before installing them in the direct insertion
connector. Tinned wires are not as secure in the connectors and could be pulled
out.
Use the supplied tie-wrap to strap the power cord to the extended tail of the connector.
Alternatively, an optional Extron PS 124 Multiple Output 12 Volt DC Power Supply (part
number 60-1022-01) can power multiple Extron 12 VDC devices using only one AC power
connector.
MTP U T A D • Installation and Operation
11
TP Cable Termination
NOTES: • RJ-45 termination with CAT 5, CAT 5e, or CAT 6 cable must comply with the
TIA/EIA T568A or TIA/EIA T568B wiring standards for all connections.
• RJ-45 termination with Skew-Free A/V UTP cable must comply with TIA/EIA
T568A only.
Figure 8 details the recommended termination of TP cables with RJ-45 connectors in
accordance with the TIA/EIA T568A or TIA/EIA T568B wiring standards. You can use either
standard with CAT 5/5e/6/7 cable, but ensure that you use the same standard on both ends
of the cable.
NOTES: • The audio data that may be carried on wire pair 3 and 6 is incompatible with
the Extron TPX 88A, which cannot switch the audio, output it locally, or break
it away.
• Enhanced Skew-Free A/V cable is not recommended for Ethernet/LAN
applications. This cable is specially designed for compatibility with Extron
Twisted Pair products that are wired using the TIA/EIA T568A standard.
• The green, brown, and blue wire pairs of this cable have virtually identical
lengths and should be used to transmit the RGB signals.
• The orange wire pair of this cable has a different length and should not be
used to transmit the RGB signals.
Side
Pins:
12345678
Pin
Insert Twisted
Pair Wires
RJ-45
Connector
T568A
T568B
Wire color
Wire color
Video input selected
RGB
Component
S-video
Audio input
Composite Stereo audio
1
White-green
White-orange Red+/V. sync+
R-Y+
Chroma (C)+
Reserved
2
Green
Orange
Red–/V. sync–
R-Y–
Chroma (C)–
Reserved
3
White-orange White-green
4
Blue
Blue
Green+
Y+
Luma (Y)+
Video+
Green–
Y–
Luma (Y)–
Video–
Mono audio+
5
White-blue
White-blue
6
Orange
Green
7
White-brown
White-brown
Blue+/H. sync+
B-Y+
Reserved
Reserved
8
Brown
Brown
Blue-/H. sync–
B-Y–
Reserved
Reserved
NOTE:
Mono audio-
If you are using Enhanced Skew-Free ™ A/V cable, use the
TIA/EIA T568A standard only.
Figure 8. TP Cable Termination
Receiver Considerations
Carefully review the following receiver considerations:
•
The video format selected in the transmitter requires a compatible receiver. A universal
receiver, such as the MTP U R RSA SEQ, is recommended.
•
Up to seven receivers (MTP RL 15HD A, with or without SEQ) can be connected in
series. This daisy chain is accomplished using the standard receivers Buffered Output
connectors. The total distance from the transmitter TP output to the last receiver in the
chain should not exceed the recommended distance for the resolution being used.
•
The receivers buffered outputs do not provide pre-peaking control. The total
recommended distance for an entire daisy chain is the same as for a single transmitter
and receiver. The transmitter Pre-Peak switch has the same effect on the recommended
transmission distance for a daisy chain as for a single transmitter and receiver.
MTP U T A D • Installation and Operation
12
•
See the recommended transmission ranges on page 3. The recommendations in
the table apply equally for a single transmitter and receiver and for a transmission daisy
chain. For example, the maximum suggested range for 1024 x 768 video is 300 feet
with Pre-Peak off and 500 feet with Pre-Peak on for either one transmitter and one
receiver or one transmitter and three daisy-chained receivers.
•
For daisy-chained units, the first receiver in the chain must be at least 100 feet from the
transmitter when the Pre-Peak switch is on.
•
For daisy-chained units, any receiver in the chain closer than 350 feet may experience
some form of over-peaking when the Pre-Peak switch is on.
Skew Delay Compensation
CAT 5/5e/6 TP cable can lead to registration errors between the red, green, and blue
video signals. Pair skew can be measured with test equipment or identified by viewing a
crosshatch test pattern with a critical eye to determine if either the red, green, or blue video
image leads (appears to the left of) the other two video images.
Try using the following methods to minimize or eliminate pair skew:
•
Use an SEQ receiver or install an SEQ 100 15HD Skew Equalizer on the receiver video
output and adjust the skew for the leading video image.
•
Switch to Extron Enhanced Skew-Free A/V UTP cable.
•
Add a skew compensation cable equal to the length of pair skew to the receiver output.
MTP U T A D • Installation and Operation
13
Reference
Information
The section provides information on:
•
Specifications
•
Part Numbers
•
Decora Template Dimensions
Specifications
Video
Gain����������������������������������������������� Unity
Number/signal type������������������������ 1 set of proprietary analog signals
Connectors������������������������������������ 1 female RJ-45
Video input and loop through
Number/signal type������������������������ 1 analog RGBHV, RGBS, RGsB, RsGsBs, component video, S-video, or composite video input
1 component video (YUV bi-level or tri-level sync)
1 S-video
1 composite video
1 buffered RGBHV, RGBS, RGsB, RsGsBs, component video, S-video, or composite video
loop through
Connectors������������������������������������ 1 female 15-pin HD (RGB, RGBS, RGsB, RsGsBs)
3 RCA (component video)
1 female 4-pin mini DIN (S-video)
1 RCA (composite video)
1 female 15-pin HD (RGB buffered loop through)
Nominal level��������������������������������� 1 Vp-p for Y of component video and S-video, and for composite video
0.7 Vp-p for RGB and for R-Y and B-Y of component video
0.3 Vp-p for C of S-video
Minimum/maximum levels�������������� 0.3 V to 1.45 Vp-p
Impedance������������������������������������� 75 ohms
Horizontal frequency���������������������� 15 kHz to 130 kHz
Vertical frequency��������������������������� 30 Hz to 150 Hz
Return loss������������������������������������� <-30 dB @ 5 MHz
DC offset (max. allowable)������������� 250 mV
Sync
Input type�������������������������������������� RGBHV, RGBS, RGsB, RsGsBs
Standards��������������������������������������� NTSC 3.58, NTSC 4.43, PAL, SECAM
Input level�������������������������������������� 3.5 V to 5.5 Vp-p, unterminated
Input impedance���������������������������� 573 ohms ±5%
Max. input voltage������������������������� 5.5 V p-p
Polarity������������������������������������������� Positive or negative (follows input polarity)
MTP U T A D • Reference Information
14
Audio
Number/signal type������������������������ 1 set of proprietary analog signals
Connectors������������������������������������ 1 female RJ-45
Gain����������������������������������������������� Unbalanced output: 0 dB;
balanced output: +6 dB
Frequency response������������������������ 20 Hz to 20 kHz, ±1 dB
THD + Noise����������������������������������� 0.15% @ 1 kHz, 0.3% @ 20 kHz at nominal level
S/N������������������������������������������������� >70 dB at maximum output (unweighted)
Stereo channel separation�������������� >60 dB @ 1 kHz
CMRR�������������������������������������������� >43 dB @ 20 Hz to 20 kHz
Audio input
Number/signal type������������������������ 2 stereo, unbalanced
Connectors������������������������������������ (1) 3.5 mm mini stereo jack
1 pair female RCA
Impedance������������������������������������� >10k ohms, unbalanced
Nominal level��������������������������������� +4 dBu (1.23 Vrms), -10 dBV (316 mVrms)
Maximum level������������������������������� +18 dBu, (unbalanced) at 1%THD+N
NOTE: 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu
General
Recommended cable type�������������� CAT 5/5E/6 (shielded or unshielded) or Extron Enhanced Skew-Free AV UTP
External power supply�������������������� 100 VAC to 240 VAC, 50-60 Hz, external;
to 12 VDC, 1 A, regulated
Power input requirements�������������� 12 VDC, 0.5 A
Temperature/humidity�������������������� Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing
Cooling������������������������������������������ Convection, no vents
Mounting
Rack mount����������������������������� No
Furniture mount���������������������� Wall or furniture mountable in a
Decora®-style opening
Enclosure type�������������������������������� Metal
Enclosure dimensions
Faceplates�������������������������������� Two [2.6" H* x 1.3" W x 0.2" D
(6.6 cm H* x 3.3 cm W x 0.6 cm D)]
(Fits the openings in a 2 gang Decora faceplate.)
*Height is 4.1" (10.4 cm) including mounting tabs.
Device������������������������������������� Two [2.7" H x 3.2" W x 1.5" D
(6.9 cm H x 8.1 cm W x 3.8 cm D)]
(Depth excludes input connectors.)
Product weight������������������������������� 0.4 lbs (0.2 kg)
Shipping weight����������������������������� 2 lbs (1 kg)
Vibration���������������������������������������� ISTA 1A in carton
(International Safe Transit Association)
Regulatory compliance
Safety�������������������������������������� CE, c-UL, UL
EMI/EMC��������������������������������� CE, C-tick, FCC Class A, ICES, VCCI
MTBF��������������������������������������������� 30,000 hours
Warranty���������������������������������������� 3 years parts and labor
NOTES: • All nominal levels are at ±10%.
• Specifications are subject to change without notice.
MTP U T A D • Reference Information
15
Part Numbers
MTP Transmitter and Compatible Devices
NOTE: A complete transmission system requires a transmitter
(MTP U T A D) and at least one MTP receiver.
Transmitter
MTP U T A D transmitter (white, black)
Part Number
60-1025-01, -02
NOTE: The following table lists an assortment of compatible
MTP receivers. In addition, the MTP U T A D is
compatible with the entire MTP product line, including
switchers and distribution amplifiers.
Compatible Devices
Part Numbers
MTP U R A receiver
60-869-03
MTP U R RSA SEQ receiver
60-869-01
MTP RL 15HD A receiver
60-690-01
MTP RL 15HD A SEQ receiver
60-690-02
MTP R 15HD RSA D receiver (white, black)
60-929-01, -02
MTP R SV A RCA receiver
60-541-62
MTP R AV RCA receiver
60-541-61
Included Parts
The following parts are included in each order for an MTP U T A D:
Included Parts
Part Numbers
Power supply, 12 VDC, 1A
28-071-57LF
Decora cover plate, white
100-358-03LF
Decora cover plate, black
100-358-04LF
5-pole captive screw connector, qty. 1
10-319-10
MTP U T A D Setup Guide
68-1674-50
Cables
NOTE: Enhanced Skew-Free™ A/V UTP cables are not
recommended for Ethernet/LAN applications.
Enhanced Skew-Free™ A/V Cable
Part Number
Enhanced Skew-Free A/V cable
(cut, various lengths)
26-569-xx
Enhanced Skew-Free A/V 1000'
(Bulk) (non-plenum)
22-141-03
Plenum enhanced Skew-Free A/V 1000'‚
(Bulk)
22-142-03
MTP U T A D • Reference Information
16
Connectors
Connector
Part Number
CAT 6 jack (black), qty. 10
100-476-01
CAT 6 jack (red), qty. 10
100-477-01
CAT 6 jack (blue), qty. 10
100-478-01
CAT 6 jack (orange), qty. 10
100-479-01
CAT 6 jack (gray), qty. 10
100-480-01
CAT 6 jack (white), qty. 10
100-481-01
CAT 6 jack (ivory), qty. 10
100-482-01
Decora Template Dimensions
To create a template, use the dimensions shown in figure 9.
NOTE: The drawing is not full size or to scale. Do
not scale up or print to use as a template.
MTP U T A D
4.60"
(11.68 cm)
3.7"
(9.4 cm)
4.50"
(11.43 cm)
2.8"
(7.1 cm)
SURFACE CUT-OUT AREA
FOR FURNITURE MOUNT
Top
Panel
To install
a 2-gang
MTP U T A D
directly into
furniture or
wall, cut
along this
line.
Figure 9. Decora Template Dimensions
MTP U T A D • Reference Information
17
Extron® Warranty
Extron Electronics warrants this product against defects in materials and workmanship for a period of three years
from the date of purchase. In the event of malfunction during the warranty period attributable directly to faulty
workmanship and/or materials, Extron Electronics will, at its option, repair or replace said products or components,
to whatever extent it shall deem necessary to restore said product to proper operating condition, provided that it is
returned within the warranty period, with proof of purchase and description of malfunction to:
USA, Canada, South America,
and Central America:
Extron Electronics
1001 East Ball Road
Anaheim, CA 92805
U.S.A.
Japan:
Extron Electronics, Japan
Kyodo Building, 16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
Europe, Africa, and the Middle
East:
Extron Europe
Hanzeboulevard 10
3825 PH Amersfoort
The Netherlands
China:
Extron China
686 Ronghua Road
Songjiang District
Shanghai 201611
China
Asia:
Extron Asia
135 Joo Seng Road, #04-01
PM Industrial Bldg.
Singapore 368363
Singapore
Middle East:
Extron Middle East
Dubai Airport Free Zone
F12, PO Box 293666
United Arab Emirates, Dubai
This Limited Warranty does not apply if the fault has been caused by misuse, improper handling care, electrical
or mechanical abuse, abnormal operating conditions, or modifications were made to the product that were not
authorized by Extron.
NOTE: If a product is defective, please call Extron and ask for an Application Engineer to receive an RA (Return
Authorization) number. This will begin the repair process.
USA: (714) 491-1500
Asia:65.6383.4400
Europe:31.33.453.4040
Japan:81.3.3511.7655
Units must be returned insured, with shipping charges prepaid. If not insured, you assume the risk of loss or damage
during shipment. Returned units must include the serial number and a description of the problem, as well as the
name of the person to contact in case there are any questions.
Extron Electronics makes no further warranties either expressed or implied with respect to the product and its quality,
performance, merchantability, or fitness for any particular use. In no event will Extron Electronics be liable for direct,
indirect, or consequential damages resulting from any defect in this product even if Extron Electronics has been
advised of such damage.
Please note that laws vary from state to state and country to country, and that some provisions of this warranty may
not apply to you.
Extron USA - West
Headquarters
Extron USA - East
Extron Europe
Extron Asia
Extron Japan
Extron China
Extron Middle East
+800.633.9876
+800.633.9876
+800.3987.6673
+800.7339.8766
Inside Asia Only
+81.3.3511.7655
+81.3.3511.7656 FAX
+400.883.1568
Inside Europe Only
+971.4.2991800
+971.4.2991880 FAX
+1.919.863.1794
+1.919.863.1797 FAX
+31.33.453.4040
+31.33.453.4050 FAX
+65.6383.4400
+65.6383.4664 FAX
Inside USA/Canada Only
+1.714.491.1500
+1.714.491.1517 FAX
Inside USA/Canada Only
© 2011 Extron Electronics All rights reserved. www.extron.com
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX