ORDERING REPLACEMENT PARTS
To order replacement parts, contact the ICON Health & Fitness, Ltd. office, or write:
ICON Health & Fitness, Ltd.
Customer Service Department
Unit 4, Revie Road Industrial Estate
Revie Road
Beeston
Leeds, LS118JG
UK
Model No. PETL62705.0
Serial No.
USER'S MANUAL
Tel:
08457 089 009
Outside the UK: (44) 113 387 7133
Fax: (44) 113 387 7125
Serial Number Decal
To help us assist you, please be prepared to give the following information:
QUESTIONS?
• the MODEL NUMBER of the product (PETL62705.0)
• the NAME of the product (PROFORM 660 VX treadmill)
• the SERIAL NUMBER of the product (see the front cover of this manual)
• the KEY NUMBER AND DESCRIPTION OF THE PART(S) (see the PART LIST on page 31 and the
EXPLODED DRAWING in the centre of this manual)
As a manufacturer, we are committed to providing complete
customer satisfaction. If you
have questions, or if there are
missing or damaged parts,
please call:
08457 089 009
Or write:
ICON Health & Fitness, Ltd.
Unit 4
Revie Road Industrial Estate
Revie Road, Beeston
Leeds, LS11 8JG
UK
email: csuk@iconeurope.com
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Save this manual
for future reference.
Part No. 228548 R0805A
Printed in USA © 2005 ICON IP, Inc.
Visit our website at
www.iconeurope.com
PART LIST—Model No. PETL62705.0
R0805A
To locate the parts listed below, see the EXPLODED DRAWING attached in the centre of this manual.
Key
No. Qty. Description
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
HOW TO USE THE CHEST PULSE SENSOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
OPERATION AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
CONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
Note: An EXPLODED DRAWING is attached in the centre of this manual.
1
2
2
6
3 39
4
1
5
6
6
2
7
4
8
8
9
2
10 2
11 4
12 2
13 1
14 1
15 2
16 1
17 1
18 2
19 2
20 1
21 1
22 2
23 1
24 2
25 2
26 1
27 1
28 2
29 4
30 1
31 2
32 8
33 14
34 1
35 2
36 1
37 1
38 1
39 1
40 2
41 1
Isolator Decal
3/4” Screw
Screw
Catch
Foot Rail Screw
Front Isolator
Hood Screw
Star Washer
Platform Bolt, Back
Platform Bolt, Front
Belt Guide Screw
Belt Guide
Left Handrail
Right Handrail
Frame Pivot Bolt
Left Foot Rail
Right Foot Rail
Isolator Bolt, Top
Isolator Top Cap
Console Frame Support
Latch Pin Assembly
Motor Bushing
Transformer
Motor Bolt
Isolator Spring
Motor Belt
Drive Motor
Frame Washer
U-nut
Outlet Assembly
Lift Frame Bolt
Lock Nut
1/2” Screw
Console
Fan Screw
Power Cord
Fan
Controller
Electronics Bracket
Rear Roller Washer
Hood
Key
No. Qty. Description
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
1
1
2
1
1
1
1
1
2
1
1
2
1
1
1
1
1
1
1
1
1
1
4
4
5
4
2
1
2
1
1
1
4
1
1
1
1
1
2
2
6
Front Roller Bushing
Lift Frame
Upright Endcap
Front Roller Bolt
Magnet
Front Roller
Walking Belt
Walking Platform
Latch Screw
Rear Roller
Left Rear Endcap
Rear Roller Bolt
Right Rear Endcap
Hex Key
Incline Stop Bracket
Ground Wire
Frame
Belly Pan
Reed Switch Bracket
Reed Switch Clip
Front Roller Nut
Reed Switch
Console Bolt
Extension Leg Bolt
Star Washer
Extension Leg Nut
Caution Decal
Warning Decal
Platform Nut
Cable Tie
Cotter Pin
Latch Housing
Tie Clamp
Releasable Tie
Access Door
Upright Wire Harness
Console Wire Harness
Key/Clip
Front Wheel
Wheel Bolt
Base Pad
PROFORM is a registered trademark of ICON IP, Inc.
2
31
Key
No. Qty. Description
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
#
#
#
#
#
10
1
1
1
1
1
2
2
2
2
2
2
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1” Tek Screw
Upright
Console Base
Incline Motor Bolt
Hair Pin Cotter Pin
Incline Motor
Extension Leg
Rear Roller Bracket
Isolator
Isolator Bottom Cap
Isolator Bracket Cover
Isolator Bolt, Bottom
Idler Arm Pivot Bolt
Idler Arm Spacer
Idler Arm
Idler Arm Spring
Idler Arm Washer
Idler Arm Nut
Idler Arm Pulley
Pulley Bolt
Power Cord Adapter
Filter
Chest Pulse Strap
Chest Pulse Sensor
iFIT Wire
Shock
Pulse Receiver
Pulse Extension Wire
Ground Wire
Shock Clip
6” Blue Wire, 2F
10” Red Wire, M/F
12” Green Wire, M/Ring
8” Black Wire, 2 Ring
User’s Manual
“#” indicates a non-illustrated part.
Specifications are subject to change
without notice.
CONDITIONING GUIDELINES
WARNING:
Before beginning this
or any exercise program, consult your physician. This is especially important for individuals over the age of 35 or individuals with preexisting health problems.
The pulse sensors are not medical devices.
Various factors, including the user's movement, may affect the accuracy of heart rate
readings. The pulse sensors are intended
only as an exercise aid in determining heart
rate trends in general.
The following guidelines will help you to plan your exercise program. For more detailed exercise information, obtain a reputable book or consult your physician.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recommended heart rates for fat burning and aerobic exercise.
To find the proper heart rate for you, first find your age
near the bottom of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers
above your age. The three numbers define your “training zone.” The lower two numbers are recommended
heart rates for fat burning; the higher number is the
recommended heart rate for aerobic exercise.
Fat Burning
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for energy. Only after the first few minutes does your body
IMPORTANT PRECAUTIONS
begin to use stored fat calories for energy. If your goal
is to burn fat, adjust the speed and incline of the treadmill until your heart rate is near the lowest number in
your training zone.
To reduce the risk of burns, fire, electric shock, or injury to persons, read the
following important precautions and information before operating the treadmill.
For maximum fat burning, adjust the speed and incline
of the treadmill until your heart rate is near the middle
number in your training zone.
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
Aerobic Exercise
2. Use the treadmill only as described.
12. Keep the power cord away from heated surfaces.
If your goal is to strengthen your cardiovascular system, your exercise must be “aerobic.” Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed and incline of the treadmill until your
heart rate is near the highest number in your training
zone.
3. Place the treadmill on a level surface, with at
least 2.5 m (8 ft.) of clearance behind it and
0.5 m (2 ft.) on each side. Do not place the
treadmill on any surface that blocks air openings. To protect the floor or carpet from damage, place a mat under the treadmill.
13. Never move the walking belt whilst the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See TROUBLESHOOTING on page 27 if the treadmill is
not working properly.)
4. Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
14. Never start the treadmill whilst you are standing on the walking belt. Always hold the
handrails whilst using the treadmill.
Each workout should include the following three parts:
5. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
15. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
A Warm-up—Start each workout with 5 to 10 minutes
of stretching and light exercise. A proper warm-up increases your body temperature, heart rate and circulation in preparation for exercise.
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
16. The pulse sensors are not medical devices.
Various factors, including the user's movement, may affect the accuracy of heart rate
readings. The pulse sensors are intended
only as an exercise aid in determining heart
rate trends in general.
WARNING:
conductor, 1mm2 (14-gauge) cord that is no
longer than 1.5 m (5 ft.).
WORKOUT GUIDELINES
Training Zone Exercise—After warming up, increase
the intensity of your exercise until your heart rate is in
your training zone for 20 to 60 minutes. (During the
first few weeks of your exercise program, do not keep
your heart rate in your training zone for longer than 20
minutes.) Breathe regularly and deeply as you exercise—never hold your breath.
A Cool-down—Finish each workout with 5 to 10 minutes of stretching to cool down. This will increase the
flexibility of your muscles and will help prevent postexercise problems.
EXERCISE FREQUENCY
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest between workouts. After a few months, you may complete up to five workouts each week if desired. The key
to success is to make exercise a regular and enjoyable
part of your everyday life.
7. The treadmill should be used only by persons
weighing 135 kg (300 lbs.) or less.
8. Never allow more than one person on the
treadmill at a time.
17. Never leave the treadmill unattended whilst it
is running. Always remove the key, unplug
the power cord, and switch the on/off switch
to the off position when the treadmill is not in
use. (See the drawing on page 5 for the location of the circuit breaker.)
9. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended for
both men and women. Always wear athletic
shoes. Never use the treadmill with bare feet,
wearing only stockings, or in sandals.
18. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 25.)
You must be able to safely lift 45 pounds (20
kg) to raise, lower, or move the treadmill.
10. When connecting the power cord (see page
10), plug the power cord into an earthed circuit. No other appliance should be on the
same circuit. When replacing the fuse, an
ASTA approved BS1362 type should be fitted
to the fuse carrier. A 13 amp fuse should be
used.
19. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
20. Inspect and properly tighten all parts of the
treadmill regularly.
11. If an extension cord is needed, use only a 3-
30
3
21. When using iFIT.com programs, an electronic
“chirping” sound will alert you when the
speed and/or incline of the treadmill is about
to change. Always listen for the “chirp” and
be prepared for speed and/or incline changes.
In some instances, the speed and/or incline
may change before the personal trainer describes the change.
player when you are not using them.
24. Never insert any object into any opening.
25.
DANGER: Always unplug the power
cord immediately after use, before cleaning the
treadmill, and before performing the maintenance and adjustment procedures described in
this manual. Never remove the motor hood unless instructed to do so by an authorized service representative. Servicing other than the
procedures in this manual should be performed
by an authorized service representative only.
22. When using iFIT.com programs, you can manually override the speed and incline settings
at any time by pressing the speed and incline
buttons. However, when the next “chirp” is
heard, the speed and/or incline will change to
the next settings of the program.
26. This treadmill is intended for in-home use
only. Do not use this treadmill in a commercial, rental, or institutional setting.
23. Remove iFIT.com CDs and videos from your
CD player or VCR and disconnect your MP3
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decals shown at the right have been placed on the
treadmill. If a decal is missing or illegible, please call the
telephone number on the front cover of this manual and
order a free replacement decal. Apply the decal in the location shown.
b. If the walking belt slips when walked on, remove
the key and UNPLUG THE POWER CORD. Using the
hex key, turn both rear roller bolts clockwise, 1/4 of a
turn. When the walking belt is correctly tightened, you
should be able to lift each edge of the walking belt 5–7
cm (2–3 in.) off the walking platform. Be careful to keep
the walking belt centred. Then, plug in the power cord,
insert the key, and walk on the treadmill for a few minutes. Repeat until the walking belt is properly tightened.
b
PROBLEM: The chest pulse sensor does not function properly
SOLUTION: a. If the chest pulse sensor does not function properly, see CHEST PULSE SENSOR TROUBLESHOOTING on page 9.
b. If the chest pulse sensor still does not function properly, the battery
should be changed. To replace the battery, first locate the battery
cover on the back of the sensor unit. Insert a coin into the slot in the
cover, and turn the cover counterclockwise to the “open” position.
Then, remove the cover.
Next, remove the old battery from the sensor unit, and insert a new
CR 2032 battery, with the battery oriented so the writing is on
top. Make sure that the rubber gasket is in place in the sensor unit.
Then, reinsert the battery cover and turn it to the closed position.
b
Battery Cover
Battery
Cover
Battery
Rubber
Gasket
PROBLEM: The incline of the treadmill does not change correctly
SOLUTION: a. With the key in the console, press one of the Incline buttons. Whilst the incline is changing, remove the key. After a few seconds, reinsert the key. The treadmill will automatically rise to the
maximum incline level and then return to the minimum level. This will recalibrate the incline system.
4
29
With the help of a second person, carefully raise the
Uprights (84) to the position shown. Next, carefully
pivot the Hood (41) off.
Locate the Reed Switch (63) and the Magnet (46) on
the left side of the Pulley (47). Turn the Pulley until the
Magnet is aligned with the Reed Switch. Make sure
that the gap between the Magnet and the Reed
Switch is about 3 mm (1/8 in.). If necessary, loosen
the Screw (3), move the Reed Switch slightly, and
then retighten the Screw. Reattach the Hood, and run
the treadmill for a few minutes to check for a correct
speed reading.
41
Top
View
84
3 mm
46
63
BEFORE YOU BEGIN
Thank you for selecting the revolutionary PROFORM®
660 VX treadmill. The 660 VX treadmill offers an impressive array of features designed to make your
workouts at home more effective and enjoyable. And
when you’re not exercising, the unique 660 VX treadmill can be folded up, requiring less than half the floor
space of other treadmills.
the telephone number on the front cover of this manual. To help us assist you, please note the product
model number and serial number before calling. The
model number of the treadmill is PETL62705.0. The
serial number can be found on a decal attached to the
treadmill (see the front cover of this manual for the location).
For your benefit, read this manual carefully before
using the treadmill. If you have questions, please call
Before reading further, please review the drawing
below and familiarise yourself with the labeled parts.
3
47
Fan
Console
Water Bottle Holder
(no bottle is included)
PROBLEM: The walking belt slows when walked on
SOLUTION: a. If an extension cord is needed, use only a 3-conductor, 1mm2 (14-gauge) cord that is no longer
than 1.5 m (5 ft.).
b. If the walking belt is overtightened, treadmill performance may decrease and the walking belt may become damaged. Remove the key and UNPLUG THE
POWER CORD. Using the hex key, turn both rear roller
bolts counterclockwise, 1/4 of a turn. When the walking
belt is properly tightened, you should be able to lift each
edge of the walking belt 5–7 cm (2–3 in.) off the walking platform. Be careful to keep the walking belt centred. Then, plug in the power cord, insert the key, and
walk on the treadmill for a few minutes. Repeat until the
walking belt is properly tightened.
Handrail
Key/Clip
b
Storage Latch
5–7 cm
On/Off Switch
Upright
Rear Roller Bolts
c. If the walking belt still slows when walked on, see the front cover of this manual.
Circuit Breaker
Walking Belt
Foot Rail
PROBLEM: The walking belt is off-centre or slips when walked on
SOLUTION: a. If the walking belt is off-centre, first remove the key
and UNPLUG THE POWER CORD. If the walking
belt has shifted to the left, use the hex key to turn
the left rear roller bolt clockwise 1/2 of a turn; if the
walking belt has shifted to the right, turn the left
bolt counterclockwise 1/2 of a turn. Be careful not to
overtighten the walking belt. Then, plug in the power
cord, insert the key, and run the treadmill for a few
minutes. Repeat until the walking belt is centred.
28
Cushioned Walking Platform
for maximum exercise comfort
a
RIGHT SIDE
BACK
Rear Roller
Adjustment Bolts
5
ASSEMBLY
TROUBLESHOOTING
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is
coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the
top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild,
non-abrasive cleaner.
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please call the telephone number on the front
cover of this manual.
Assembly requires the included hex key
shaft at least 6” long) and wire cutters
and your own phillips screwdriver
.
(with a
Use the drawings below to identify the hardware used during assembly. Note: If a part is not in the parts bag,
check to see if it has been preattached to one of the parts to be assembled.
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a properly earthed outlet. (See page 10.) If an extension cord is needed, use only a 3-conductor, 1 mm2 (14-gauge) cord that is no longer than 1.5
m (5 ft.). Important: The treadmill is not compatible with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is inserted into the console.
c. Check the circuit breaker located on the treadmill
frame near the power cord. If the switch protrudes as
shown, the circuit breaker has tripped. To reset the
circuit breaker, wait for five minutes and then press
the switch back in.
Extension Leg Nut (67)–4
1” Tek Screw (83)–4
Star Washer (8)–8
d. Check the on/off switch located on the treadmill
frame near the power cord. Make sure that the switch
is in the on position.
Latch Screw (50)–2
c
Tripped
Reset
d
On
Position
PROBLEM: The power turns off during use
Console Bolt (64)–4
Extension Leg Bolt (65)–4
SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see c. above). If the
circuit breaker has tripped, wait for five minutes and then press the switch back in.
1. Make sure that the power cord is unplugged.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
1
With the help of a second person, carefully tip the
treadmill onto its left side as shown. Partially fold the
Frame (58) so the treadmill is more stable. Do not fully
fold the treadmill until it is completely assembled.
84
c. Remove the key from the console. Reinsert the key into the console.
65
8
d. Make sure that the on/off switch is in the on position.
e. If the treadmill still will not run, see the front cover of this manual.
Insert an Extension Leg (89) into the base of the Uprights
(84) as shown. Next, hold two Extension Leg Nuts (67) in
the bottom of the Extension Leg. Then, insert two
Extension Leg Bolts (65) with Star Washers (8) into the
top of the Extension Leg, and firmly tighten the Extension
Leg Bolts into the Extension Leg Nuts.
With the help of a second person, carefully tip the treadmill onto its other side. Attach the other Extension Leg
(not shown) as described above.
82
82
83
67
89
58
PROBLEM: The display of the console does not function properly
SOLUTION: a. Remove the key from the console and UNPLUG THE
POWER CORD. With the help of a second person,
carefully tip the Uprights (84) down as shown. Next,
remove the three Screws (3) and the three Hood
Screws (7). Note: A phillips screwdriver with a shaft at
least 5” long is required.
Attach four Base Pads (82) (only two are shown) to the
base of the Uprights (84) with four 1” Tek Screws (83).
a
3
7
3
84
6
27
HOW TO LOWER THE TREADMILL FOR USE
2. With the help of a second person, carefully raise the
Uprights (84) to a vertical position.
1. Hold the upper end of the treadmill with your right hand. Pull
the latch knob to the left and hold it. Pivot the frame down
until the catch is past the latch pin.
Console
Assembly
Have the second person hold the console assembly near
the Uprights (84) as shown. Look under the console assembly and locate the Console Wire Harness (78).
Catch
Latch Knob
Latch Pin
2. Hold the frame firmly with both hands, and lower the frame to
the floor. Do not drop the frame to the floor. To decrease
the possibility of injury, bend your legs and keep your
back straight.
2
Open
Cut the plastic ties securing the Upright Wire Harness
(77) to the right Upright (84). Next, connect the Upright
Wire Harness to the Console Wire Harness (78). Make
sure to connect the connectors properly (see the
inset drawing). The connectors should slide together
easily and snap into place. If the connectors do not
slide together easily and snap into place, turn one connector and then try again. IF THE CONNECTORS ARE
NOT CONNECTED PROPERLY, THE CONSOLE MAY
BE DAMAGED WHEN THE POWER IS TURNED ON.
78
77
78
84
77
3. Insert the Wire Harnesses (77, 78) down into the right
Upright (84).
3
Console
Assembly
Set the console assembly on the Uprights (84). Be careful to avoid pinching the Wire Harnesses (77, 78).
Whilst a second person holds the console assembly, attach it with four Console Bolts (64) and four Star Washers
(8) as shown; start all four Console Bolts and then
firmly tighten them.
77, 78
8
8
64
64
84
4. Orient the Latch Housing (73) so the large hole is on the
indicated side. Attach the Latch Housing to the left
Upright (84) with two Latch Screws (50); start both
Latch Screws and then tighten them.
Remove the knob from the pin. Make sure that the collar
and the spring are on the pin. (Note: If there are two collars, place one on each side of the spring.) Next, insert
the pin into the Latch Housing (73). Then, tighten the
knob back onto the pin.
84
4
84
73
Knob
Spring
50
Large
Hole
26
7
Collar
Pin
5. Place the treadmill in the storage position (see HOW TO
FOLD AND MOVE THE TREADMILL on page 25).
5
112
84
Next, place the cylinder end of the Shock (108) near the
bracket on the base of the Uprights (84).
HOW TO FOLD THE TREADMILL FOR STORAGE
112
108
See the two small inset drawings. Using your fingernail
or the end of a screwdriver, press on the end of the
Shock Pin (112) to loosen it from the Shock (108). Next,
rotate the Shock Pin and pull it out of the Shock. Be
careful to avoid losing the Shock Pin.
Bracket
112
5a
See drawing 5a. Press the cylinder end of the Shock
(108) onto the ball on the bracket. Next, insert the end of
the Shock Pin (112) through two of the small holes in the
end of the Shock. Then, rotate the Shock Pin until it clips
onto the Shock.
6. Raise the Shock (108) to a vertical position. Remove the
Shock Pin (112) from the raised end of the Shock as described in step 5. If necessary, rotate the Shock to align
the end of the Shock with the ball on the bracket on the
Frame (58).
112
108
Bracket
6
58
112
Plug in the power cord as described on page 10. Turn on
the power as described on page 12. Next, press the
Incline increase and decrease buttons until the ball on
the bracket is aligned with end of the Shock (108). Then,
press the end of the Shock onto the ball. Note: It may be
necessary to press the end of the Shock onto the ball
whilst the Frame is moving.
See drawing 6a. Insert the Shock Pin (112) into the two
indicated small holes in the end of the Shock (108).
Then, rotate the Shock Pin until it clips onto the Shock.
Note: Extra Shock Clips are included.
HOW TO FOLD AND MOVE THE TREADMILL
Bracket
108
Before folding the treadmill, adjust the incline to the
lowest position. If this is not done, the treadmill may become permanently damaged. Next, unplug the power cord.
CAUTION: You must be able to safely lift 45 pounds (20 kg)
to raise, lower, or move the treadmill.
1. Hold the treadmill frame with your hands in the location
shown by the arrow at the right. To decrease the possibility
of injury, bend your legs and keep your back straight. As
you raise the frame, make sure to lift with your legs
rather than your back. Raise the frame about halfway to the
vertical position.
2. Move your right hand to the position shown and hold the
treadmill firmly. Using your left hand, pull the latch knob to
the left and hold it. Raise the frame until the catch passes the
latch pin. Slowly release the latch knob. Make sure that the
catch is resting against the latch pin.
To protect the floor or carpet from damage, place a mat
under the treadmill. Keep the treadmill out of direct sunlight. Do not leave the treadmill in the storage position in
temperatures above 85° Fahrenheit.
Catch
Engaged
Latch Knob
Latch Pin
6a
HOW TO MOVE THE TREADMILL
Holes
108
Before moving the treadmill, convert the treadmill to the storage
position as described above. Make sure that the catch is resting against the latch pin.
112
Press the Incline decrease button until the treadmill is at
the lowest incline level. Then, unplug the power cord.
7. Make sure that all parts are properly tightened before you use the treadmill. If there are sheets of clear
plastic on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the treadmill. Note: Extra hardware may be included. Keep the included hex key in a secure place; the large hex key is
used to adjust the walking belt (see page 28).
1. Hold the upper ends of the handrails. Place one foot against
one of the wheels.
2. Tilt the treadmill back until it rolls freely on the front wheels.
Carefully move the treadmill to the desired location. To reduce the risk of injury, use extreme caution whilst moving the treadmill. Do not move the treadmill over an uneven surface.
3. Place one foot against one of the wheels, and carefully lower
the treadmill until it is resting in the storage position.
8
25
Base
Wheel
THE INFORMATION MODE/DEMO MODE
IMPORTANT: If a
“d” appears in the
lower left corner
of the display, the
console is in the
“demo” mode.
This mode is intended to be used
only when a
treadmill is displayed in a store. When the console is in
the demo mode, the power cord can be plugged in, the
key can be removed from the console, and the indicators in the display will automatically appear in a preset
sequence; the buttons on the console will not operate. If
a “d” appears when the information mode is selected, press the Speed – button so “d” disappears.
The console features an information mode that keeps
track of the total number of hours that the treadmill has
been operated and the total number of miles that the
walking belt has moved. The information mode also allows you to select miles or kilometres as the unit of
measurement and to turn on and turn off the demo
mode.
To select the information mode, hold down the Stop
button whilst inserting the key into the console, and
then release the Stop button. When the information
mode is selected, the following information will be
shown in the display:
HOW TO USE THE CHEST PULSE SENSOR
HOW TO PUT ON THE CHEST PULSE SENSOR
• Store the chest pulse sensor in a warm, dry place.
Do not store the chest pulse sensor in a plastic bag
or other container that may trap moisture.
The chest pulse sensor consists of two components:
the chest strap and the sensor unit (see the drawing
below). Insert the tab on one end of the chest strap into
the hole in one end of the sensor unit, as shown in the
inset drawing. Press the end of the sensor unit under
the buckle on the chest strap. The tab should be flush
with the front of the sensor unit.
• Do not expose the chest pulse sensor to direct sunlight for extended periods of time; do not expose it to
temperatures above 50° C (120° F) or below -10° C
(15° F).
• Do not excessively bend or stretch the sensor unit
when using or storing the chest pulse sensor.
• Clean the sensor unit using a damp cloth—never
use alcohol, abrasives, or chemicals. The chest
strap may be hand washed and air dried.
Chest Strap
The priority display will show the
total number of
kilometres (or
miles) that the
walking belt has
moved. The
lower right corner
of the display will
show the total number of hours that the treadmill has
been used. In addition, an “M” for metric kilometres or
an “E” for English miles will appear in the lower left corner of the display. Press the Speed + button to change
the unit of measurement.
To exit the information mode, remove the key from the
console.
Tabs
Tab
Sensor Unit
Sensor
Unit
CHEST PULSE SENSOR TROUBLESHOOTING
The instructions on the following pages explain
how the chest pulse sensor is used with the console. If the chest pulse sensor does not function
properly, try the steps below.
Buckle
• Make sure that you are wearing the chest pulse sensor as described at the left. Note: If the chest pulse
sensor does not function when positioned as described, move it slightly lower or higher on your chest.
Next, wrap the chest
pulse sensor around
your chest and attach
the other end of the
chest strap to the
sensor unit. Adjust
the length of the
chest strap, if necessary. The chest pulse
sensor should be under your clothes, tight against your
skin, and as high under the pectoral muscles or
breasts as is comfortable. Make sure that the logo on
the sensor unit is facing forward and is right-side-up.
• Use saline solution such as saliva or contact lens
solution to wet the two electrode areas on the sensor
unit. If heart rate readings do not appear until you
begin perspiring, rewet the electrode areas.
• As you walk or run on the treadmill, position yourself near the centre of the walking belt. For the console to display heart rate readings, the user must
be within arm’s length of the console.
Next, pull the sensor unit away from your body a few
inches and locate the two electrode areas on the inner
side (the electrode areas are covered by shallow
ridges). Using saline solution such as saliva or contact
lens solution, wet both electrode areas. Return the
sensor unit to a position against your chest.
• The chest pulse sensor is designed to work with
people who have normal heart rhythms. Heart rate
reading problems may be caused by medical conditions such as premature ventricular contractions
(pvcs), tachycardia bursts, and arrhythmia.
• The operation of the chest pulse sensor can be affected by magnetic interference caused by high
power lines or other sources. If it is suspected that
this is a problem, try relocating the treadmill.
CHEST PULSE SENSOR CARE AND MAINTENANCE
• Thoroughly dry the chest pulse sensor after each
use. The chest pulse sensor is activated when the
electrode areas are wetted and the heart rate
monitor is put on; the chest pulse sensor shuts off
when it is removed and the electrode areas are
dried. If the chest pulse sensor is not dried after
each use, it may remain activated longer than necessary, draining the battery prematurely.
24
• The CR2032 battery may need to be replaced (see
page 29).
9
OPERATION AND ADJUSTMENT
7
HOW TO USE AN IFIT.COM PROGRAM
DIRECTLY FROM OUR WEB SITE
THE PRE-LUBRICATED WALKING BELT
Your treadmill features a walking belt coated with high-performance lubricant. IMPORTANT: Never apply silicone spray or other substances to the walking belt or the walking platform. Such substances will deteriorate the walking belt and cause excessive wear.
This product must be earthed. If it should malfunction or break
down, earthing provides a path of least resistance for electric current to reduce the risk of electric shock. This product is equipped
with a power cord having an equipment-earthing conductor and an
earthing plug. Important: If the power cord is damaged, it must
be replaced with a manufacturer-recommended power cord.
1
Socket on Treadmill
See drawing 3. Plug the power cord into an appropriate outlet that is
properly installed and earthed in accordance with all local codes and
ordinances. Important: The treadmill is not compatible with
GFCI-equipped outlets.
If the speed or incline settings are too high or too
low, you can manually override the settings at any
time by pressing the Speed or Incline buttons on
the console. However, when the next “chirp” is
heard, the speed and/or incline will change to
the next settings for the program.
Follow the steps below to use a program from our
Web site.
See drawing 1. Plug the indicated end of the power cord into the
socket on the treadmill.
See drawing 2. Press the pins on the other end of the power cord
into the indicated metal clips in the adapter. Close the adapter cover
over the end of the power cord and tighten the screw in the adapter.
Important: Make sure that the adapter cover is secure and that
the screw has been tightened before using the power cord.
When the on-screen countdown ends, the program
will begin and the walking belt will begin to move.
Hold the handrails, step onto the walking belt, and
begin walking. During the program, an electronic
“chirping” sound will alert you when the speed
and/or incline of the treadmill is about to change.
CAUTION: Always listen for the “chirp” and be
prepared for speed and/or incline changes.
Our Web site at www.iFIT.com allows you to access
basic programs, audio programs, and video programs
directly from the internet. Additional options are soon to
be available. See www.iFIT.com for details.
To use programs from our Web site, the treadmill must
be connected to your home computer. See HOW TO
CONNECT YOUR COMPUTER on page 20. In
addition, you must have an internet connection and
an internet service provider. A list of specific system requirements is found on our Web site.
HOW TO PLUG IN THE POWER CORD
1
2
Adapter
Cover
Screw
3
Metal
Clips
Outlet
To stop the walking belt at any time, press the
Stop button on the console. To restart the program, press the Start button or the Speed + button. After a moment, the walking belt will begin to
move at 2 km/h. When the next “chirp” is heard,
the speed and incline will change to the next
settings of the program.
Select the iFIT.com mode.
See step 2 on page 21.
Pins
Adapter
Insert the key into the console.
See HOW TO TURN ON THE POWER on page 12.
2
3
Go to your computer and start an internet
connection.
4
Start your web browser, if necessary, and go to
our Web site at www.iFIT.com.
5
Follow the desired links on our Web site to select a program.
When the program is completed, the walking belt
will stop. Note: To use another program, press the
Stop button and go to step 5.
Note: If the speed and/or incline of the treadmill
does not change when a “chirp” is heard, make
sure that the letters “iFIT” appear in the matrix
and that the time is not flashing in the display.
In addition, make sure that the audio cable is
properly connected.
Read and follow the on-line instructions for using a
program.
6
Return to the treadmill and stand on the foot
rails. Find the clip attached to the key and slide
the clip onto the waistband of your clothes.
8
Follow the on-line instructions to start the
program.
Follow your progress with the matrix and the
display.
See step 5 on page 12.
DANGER: Improper connection of the equipment-earthing conductor can result in an in-
When you start the program, an on-screen countdown will begin.
9
creased risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as
to whether the product is properly earthed. Do not modify the plug provided with the product—if it will
not fit the outlet, have a proper outlet installed by a qualified electrician.
10
When you are finished exercising, remove the
key from the console.
See step 8 on page 15.
23
• Adjust the volume of your MP3 player, CD
player, or VCR. If the volume is too high or too
low, the console may not detect the program
signals.
During the program, an electronic “chirping” sound
will alert you when the speed and/or incline of the
treadmill is about to change. CAUTION: Always
listen for the “chirp” and be prepared for speed
and/or incline changes. In some instances, the
speed and/or incline may change before your
personal trainer describes the change.
• Make sure that the audio cable is properly
connected.
• If you are using a portable CD player and the
CD skips, set the CD player on the floor or another flat surface instead of on the console.
If the speed or incline settings are too high or too
low, you can manually override the settings at any
time by pressing the Speed or Incline buttons on
the console. However, when the next “chirp” is
heard, the speed and/or incline will change to
the next settings of the program.
4
Follow your progress with the matrix and the
display.
See step 5 on page 12.
To stop the walking belt at any time, press the
Stop button on the console. To restart the program, press the Start button or the Speed + button. After a moment, the walking belt will begin to
move at 2 km/h. When the next “chirp” is
heard, the speed and/or incline will change to
the next settings of the program.
5
Measure your heart rate if desired.
See step 6 on page 13.
6
Key
Turn on the fan if desired.
Clip
See step 7 on page 13.
When the program is completed, the walking belt
will stop. Note: To use another MP3, CD, or video
program, press the Stop button or remove the key
and go to step 1 on page 21.
7
Note: If the speed and/or incline of the treadmill
does not change when a “chirp” is heard:
When you are finished exercising, remove the
key from the console.
See step 8 on page 15.
CAUTION: Always remove iFIT.com CDs and
videocassettes from your CD player and VCR
and disconnect your MP3 player when you are
not using them.
• Make sure that the letters “iFIT” appear in the
matrix and that the time is not flashing in the
display. If the time is flashing, press the Start
button or the Speed + button on the console.
FEATURES OF THE CONSOLE
separately). IFIT.com programs automatically control
the speed and incline of the treadmill as a personal
trainer guides you through every step of your workout;
high-energy music provides added motivation. To
download iFIT.com MP3 programs, go to
www.iFIT.com. To purchase iFIT.com CDs or videocassettes, call the telephone number on the front
cover of this manual.
The treadmill console offers an impressive array of
features designed to make your workouts more effective. When the manual mode of the console is selected, you can change the speed and incline of the
treadmill with the touch of a button. As you exercise,
the console will display continuous exercise feedback.
You can even measure your heart rate using the handgrip pulse sensor or the chest pulse sensor.
With the treadmill connected to your computer, you
can also go to www.iFIT.com and access iFIT.com
programs directly from our Web site. See
www.iFIT.com for more information.
In addition, the console features 12 preset programs.
Each preset program automatically controls the speed
and incline of the treadmill as it guides you through an
effective workout. The console also offers four pulse
programs that control the speed and incline of the
treadmill to keep your heart rate near target heart rate
settings during your workouts. In addition, a fitness test
program measures your VO2 max, or aerobic capacity.
To use the manual mode of the console, follow the
steps beginning on page 12. To use a preset program, see page 14. To use a pulse program, see
page 16. To use the fitness test program, see page
18. To use an iFIT.com MP3, CD, or video program,
see page 21. To use an iFIT.com program directly
from our Web site, see page 23.
The console also features iFIT.com interactive technology. Having iFIT.com technology is like having a personal trainer in your home. Using the included audio
cable, you can connect the treadmill to your portable
stereo, home stereo, computer, or VCR and play special iFIT.com MP3, CD, and video programs (iFIT.com
MP3 programs, CDs, and videocassettes are available
22
Note: If there is a sheet of clear plastic on the face
of the console, remove the plastic. To prevent damage to the walking platform, always wear clean
shoes when using the treadmill.
11
HOW TO TURN ON THE POWER
Plug in the power cord
(see page 10). Next, locate
the on/off switch on the
treadmill frame near the
power cord. Make sure that
the switch is in the on position.
crements of 0.5 km/h. Note: After the buttons are
pressed, it may take a moment for the walking belt
to reach the selected speed setting.
On
Position
If one of the ten numbered speed buttons is
pressed, the walking belt will gradually increase in
speed until it reaches the selected speed setting.
To stop the walking belt, press the Stop button. To
restart the walking belt, press the Start button, the
Speed + button, or one of the ten numbered buttons.
Next, stand on the foot rails of the treadmill. Find the
clip attached to the key (see the drawing on page 11),
and slide the clip onto the waistband of your clothes.
Then, insert the key into the console. After a moment,
the matrix and the display will light. Test the clip by
carefully taking a few steps backward until the key
is pulled from the console. If the key is not pulled
from the console, adjust the position of the clip as
needed.
Note: The first time the treadmill is used, observe
the alignment of the walking belt, and align the
walking belt if necessary (see page 28).
To use an iFIT.com MP3, CD, or video program, the
treadmill must be connected to your MP3 player, CD
player, or VCR. See HOW TO CONNECT THE
TREADMILL TO USE IFIT.COM PROGRAMS on
pages 19 to 21. To download iFIT.com MP3 programs, go to www.iFIT.com. To purchase iFIT.com
CDs or videocassettes, call the telephone number
on the front cover of this manual.
A. Plug one end of a long 3.5 mm to RCA stereo audio
cable (available at electronics stores) into the input
jack on the console. Plug the other end of the cable
into the AUDIO OUT jack on your VCR.
Follow the steps below to use an iFIT.com MP3, CD,
or video program.
A
ANT. IN
RF OUT
CH
3 4
4
Change the incline of the treadmill as desired.
5
Insert the key into the console.
LEFT
Follow your progress with the matrix and the
display.
Note: The matrix and the display can be backlit
with any of five colors. To select the desired
color, press the Display Color button repeatedly.
Select the manual mode.
When the manual
mode, the fitness test
program, or the
iFIT.com mode is selected, the matrix will
show a 400-metre (1/4mile) track. As you walk
or run on the treadmill,
the indicators around
the track will appear in succession until the entire
track appears. The track will then disappear and
the indicators will again begin to appear in succession.
Start the walking belt.
To start the walking belt, press the Start button,
the Speed + button, or one of the ten numbered
speed buttons.
The lower left corner of
the display will show the
approximate number of
calories you have
burned and the incline
level of the treadmill.
When you use the handgrip pulse sensor or the
chest pulse sensor, the lower left corner of the display will also show your heart rate.
If the Start button or the Speed + button is
pressed, the walking belt will begin to move at 2
km/h. As you exercise, change the speed of the
walking belt as desired by pressing the Speed +
and – buttons. Each time a button is pressed, the
speed setting will change by 0.1 km/h; if a button
is held down, the speed setting will change in in-
12
1
AUDIO OUT
RIGHT
To change the incline of the treadmill, press the
Incline increase and decrease buttons. Each time
a button is pressed, the incline will change by
0.5%. Note: After the buttons are pressed, it may
take a moment for the treadmill to reach the selected incline setting.
When the key is inserted, the manual
mode will be selected.
If a program or the
iFIT,com mode has
been selected, reselect
the manual mode by
pressing the iFIT button repeatedly until a
track appears in the matrix but the letters “iFIT” do
not appear.
3
Note: If your VCR has an unused AUDIO OUT jack,
see instruction A below. If the AUDIO OUT jack is
being used, see instruction B. If you have a TV
with a built-in VCR, see instruction B. If your VCR
is connected to your home stereo, see HOW TO
CONNECT YOUR HOME STEREO on page 20.
OUT
See HOW TO TURN ON THE POWER above.
2
HOW TO USE AN IFIT.COM MP3, CD, OR VIDEO
PROGRAM
VIDEO AUDIO
IN
HOW TO USE THE MANUAL MODE
1
HOW TO CONNECT YOUR VCR
Insert the key into the console.
See HOW TO TURN ON THE POWER on page 12.
2
Select the iFIT.com mode.
To select the iFIT.com
mode, press the iFIT
button repeatedly until
a track and the letters
“iFIT” appear in the
matrix.
Audio Cable
B. Plug one end of a long 3.5 mm to RCA stereo audio
cable (available at electronics stores) into the input
jack on the console. Plug the other end of the cable
into an RCA Y-adapter (available at electronics
stores). Next, remove the wire that is currently
plugged into the AUDIO OUT jack on your VCR and
plug the wire into the unused side of the Y-adapter.
Plug the Y-adapter into the AUDIO OUT jack on
your VCR.
3
A
Press the Play button on your CD player or
VCR.
Note: If you are using an iFIT.com CD, insert the
CD into your CD player; if you are using an
iFIT.com videocassette, insert the videocassette
into your VCR.
B
ANT. IN
VIDEO AUDIO
IN
RF OUT
CH
3 4
A moment after the Play button is pressed, your
personal trainer will begin guiding you through
your workout. Simply follow your personal trainer’s
instructions. Note: If the time is flashing in the display, press the Start button or the Speed + button
on the console. The treadmill will not respond to
an MP3, CD, or video program whilst the time is
flashing in the display.
OUT
Audio Cable
RCA
Y-adapter
Wire removed from
AUDIO OUT jack
21
HOW TO CONNECT YOUR HOME STEREO
HOW TO CONNECT YOUR COMPUTER
Note: If your stereo has an unused LINE OUT jack,
see instruction A below. If the LINE OUT jack is
being used, see instruction B.
A. Plug one end of a long 3.5 mm to 3.5 mm stereo
audio cable (available at electronics stores) into the
input jack on the console. Plug the other end of the
cable into the LINE OUT jack on your computer.
Note: Whilst the cable is plugged into the LINE OUT
jack, do not plug your headphones into the headphone jack on the console.
A. Plug one end of a long 3.5 mm to RCA stereo audio
cable (available at electronics stores) into the input
jack on the console. Plug the other end of the cable
into the LINE OUT jack on your stereo. Note: Whilst
the cable is plugged into the LINE OUT jack, do not
plug your headphones into the headphone jack on
the console.
A
A
LINE OUT
The centre of the display is the priority display. Press the Priority
Display button repeatedly until the priority
display shows the information that you are
most interested in viewing.
CD
VCR
Amp
LINE OUT
Audio Cable
LINE OUT
B. Plug one end of a long 3.5 mm to RCA stereo audio
cable (available at electronics stores) into the input
jack on the console. Plug the other end of the cable
into an RCA Y-adapter (available at electronics
stores). Next, remove the wire that is currently
plugged into the LINE OUT jack on your stereo and
plug the wire into the unused side of the Y-adapter.
Plug the Y-adapter into the LINE OUT jack on your
stereo. Note: Whilst the Y-adapter is plugged into
the LINE OUT jack, do not plug your headphones
into the headphone jack on the console.
Audio
Cable
8
6
LINE OUT
When you are finished using the treadmill,
switch the on/off switch to the off position and
unplug the power cord.
Measure your heart rate if desired.
To use the chest pulse sensor, see page 9. To
use the handgrip pulse sensor, see the instructions below. Note: If you use the chest pulse sensor and the handgrip pulse sensor at the same
time, the console will not display your heart rate
accurately.
RCA
Y-adapter
Wire removed from
LINE OUT jack
20
When you are finished exercising, remove the
key from the console.
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to the lowest
setting. The incline must be at the lowest setting
when the treadmill is folded to the storage position or the treadmill will be damaged. Next, remove the key from the console and put it in a secure place. Note: If the display remains lit after
the key is removed, the console is in the
“demo” mode. See page 24 and turn off the
demo mode.
To reset the display, press the Stop button, remove the key, and then reinsert the key.
VCR
Turn on the fan if desired.
To turn on the fan, press the Fan button. To turn
on the fan at high speed, press the button a second time. To turn off the fan, press the button a
third time. Note: If the fan is left on when the walking belt is stopped, the fan will automatically turn
off after a few minutes.
Note: The console can display speed and distance in either kilometres or miles. A “Km/H” will
appear in the right side of the display when the
console is displaying speed and distance in kilometres. To change the unit of measurement, see
THE INFORMATION MODE/DEMO MODE on
page 24. Note: For simplicity, all instructions in
this section refer to kilometres.
CD
Amp
7
The Intensity display
will indicate the approximate intensity level of
your exercise. Level 10
is the highest intensity
level.
Audio Cable
B
To use the
handgrip pulse
sensor, first remove the sheets
of clear plastic
from the metal
Contacts
contacts. In addition, make
sure that your
hands are clean. Next, stand on the foot rails
and hold the metal contacts—avoid moving your
hands. When your pulse is detected, the heart
symbol in the lower left corner of the display will
appear, one or two dashes will appear, and then
your heart rate will be shown. For the most accurate heart rate reading, continue to hold the
contacts for about 15 seconds.
The lower right corner
of the display will show
the distance that you
have walked or run, the
elapsed time, your
pace (in minutes per
mile), and the speed of the walking belt. Note:
When a program is selected (except for pulse program 4 and the fitness test program), the lower
right corner of the display will show the time remaining in the program instead of the elapsed
time.
13
settings for the next several segments will be
shown in the columns to the right.
HOW TO USE A PRESET PROGRAM
1
When only three seconds remain in the first segment of the program, both the Current Segment
column and the column to the right will flash and a
series of tones will sound. If the speed and/or incline of the treadmill is about to change, the speed
setting and/or the incline setting will flash in the
display to alert you.
Insert the key into the console.
See HOW TO TURN ON THE POWER on page
12.
2
Select one of the preset programs.
To select a preset program, press the Programs
button repeatedly until “P1,” “P2,” “P3,” or “P12”
appears in the priority display.
When the first segment is completed, all speed
settings will move one column to the left. The
speed setting for the second segment will then be
shown in the flashing Current Segment column
and the treadmill will automatically adjust to the
speed and incline settings for the second segment. Note: If all seven of the indicators in the
Current Segment column are lit, the speed settings
may move downward so that only the highest indicators appear in the matrix.
The program will continue in this way until the
speed setting for the last segment is shown in the
Current Segment column and the last segment
ends. The walking belt will then slow to a stop.
A few seconds after a preset program is selected,
the maximum incline setting of the program and
the maximum speed setting of the program will
flash in the display for a few seconds. The display
will also show how long the program will last. A
profile of the speed settings of the program will
scroll across the matrix.
3
Note: If your stereo has an RCA-type AUDIO OUT
jack, see instruction A below. If your stereo has a
3.5 mm LINE OUT jack, see instruction B. If your
stereo has only a PHONES jack, see instruction C.
To use iFIT.com MP3 or CD programs, the treadmill
must be connected to your MP3 player, CD player,
portable stereo, home stereo, or computer. See pages
19 and 20 for connecting instructions. To use iFIT.com
programs directly from our Web site, the treadmill
must be connected to your computer. See page 20 for
connecting instructions. To use iFIT.com video programs, the treadmill must be connected to your VCR.
See page 21 for connecting instructions.
A. Plug one end of a long 3.5 mm to RCA stereo audio
cable (available at electronics stores) into the input
jack on the console. Plug the other end of the cable
into the AUDIO OUT jack on your stereo.
A/B
HOW TO CONNECT YOUR MP3 PLAYER OR CD
PLAYER
AUDIO OUT
If the speed or incline setting for the current segment is too high or too low, you can manually
override the setting by pressing the Speed or
Incline buttons. Every few times a Speed button is
pressed, an additional indicator will appear or disappear in the Current Segment column; if any of
the columns to the right of the Current Segment
column have the same number of lit indicators as
the Current Segment column, an additional indicator may appear or disappear in those columns as
well. Important: When the current segment of
the program ends, the treadmill will automatically adjust to the speed and incline settings
for the next segment.
A moment after the button is pressed, the treadmill will automatically adjust to the first speed and
incline settings of the program. Hold the handrails
and begin walking.
Each program is divided into several one-minute
segments. One speed setting and one incline setting are programmed for each segment. Note: The
same speed setting and/or incline setting may be
programmed for two or more consecutive segments.
LEFT
A. Plug one end of the included 3.5 mm to 3.5 mm
stereo audio cable into the input jack on the console. Plug the other end of the cable into a jack on
your MP3 player or CD player. Plug your headphones into the headphone jack on the console.
Audio Cable
A
B. See the drawing above. Plug one end of a long 3.5
mm to 3.5 mm stereo audio cable (available at electronics stores) into the input jack on the console.
Plug the other end of the cable into the LINE OUT
jack on your stereo. Note: Whilst the cable is
plugged into the LINE OUT jack, do not plug your
headphones into the headphone jack on the console.
LINE OUT
PHONES
Audio
Cable
C. Plug one end of a long 3.5 mm to 3.5 mm stereo
audio cable (available at electronics stores) into the
input jack on the console. Plug the other end of the
cable into the PHONES jack on your stereo. Plug
your headphones into the headphone jack on the
console.
Headphones
C
To stop the program at any time, press the Stop
button. To restart the program, press the Start button or the Speed + button. The walking belt will
begin to move at 2 km/h. When the next segment
of the program begins, the treadmill will automatically adjust to the speed and incline settings for the
next segment.
Current
Segment
PHONES
Audio
Cable
Headphones
14
LINE OUT
RIGHT
PHONES LINE OUT
Press the Start button or the Speed + button to
start the program.
The speed setting for
the first segment will
be shown in the flashing Current Segment
column of the matrix.
(The incline settings
are not shown in the
matrix.) The speed
HOW TO CONNECT YOUR PORTABLE STEREO
HOW TO CONNECT THE TREADMILL TO USE
IFIT.COM PROGRAMS
19
5
HOW TO USE THE FITNESS TEST PROGRAM
Next, the word “AGE” and the current age setting
will appear in the display. If you have not entered
your age, press the increase and decrease buttons above the Pulse Control button to enter your
age.
The fitness test program measures your approximate
VO2 max, or aerobic capacity. VO2 max is a measure
of your ability to intake and utilize oxygen to generate
energy for endurance activities such as running and
cycling. In technical terms, VO2 max is the maximum
volume of oxygen, in milliliters, that your body can use
in one minute, per kilogram of body weight. A high VO2
max indicates a high level of cardiorespiratory fitness.
Note: To learn more about VO2 max, refer to a reputable book or consult your physician.
6
Put on the chest pulse sensor.
Select the fitness test program.
To select the fitness test program, press the Pulse
Control button repeatedly until the word “FIt” appears in the priority display.
4
7
5
Measure your heart rate if desired.
See step 6 on page 13.
6
Turn on the fan if desired.
When you are finished using the treadmill,
switch the on/off switch to the off position and
unplug the power cord.
See step 7 on page 13.
Note: If your pulse is not detected for several seconds during the program (the letters “PLS” will
flash in the display), or if your heart rate exceeds
85% of your age-predicted maximum heart rate
for several seconds during the program, the program may stop and “Vo2 – – –” may appear in the
display. If this occurs, try the program again on
another day. Make sure that you are wearing the
chest pulse sensor as described on page 9.
7
Enter your gender.
Follow your progress with the matrix and the
display.
See step 5 on page 12.
When the fitness test program is selected, the letters “GEn” (gender) and “M” (male) or “F” (female)
will appear in the display (see the drawing above).
Press the increase and decrease buttons above
the Pulse Control button to enter your gender, and
then press the Start button. Note: Pressing the
Start button at this time will not start the fitness
test program.
8
Turn on the fan if desired.
See step 7 on page 13.
9
When you are finished exercising, remove the
key from the console.
See step 8 on page 15.
18
When you are finished exercising, remove the
key from the console.
When the program ends, make sure that the incline of the treadmill is at the lowest setting.
Next, remove the key from the console and put it in
a safe place. Note: If the display remains lit
after the key is removed, the console is in the
“demo” mode. See page 24 and turn off the
demo mode.
See step 5 on page 12.
The program is designed to last for nine
minutes. When the program ends, the walking
belt will slow to a stop
and your VO2 max will
appear in the display.
Insert the key into the console.
See HOW TO TURN ON THE POWER on page 12.
3
Follow your progress with the matrix and the
display.
During the program, the speed and incline of the
treadmill will periodically change. The speed setting or the incline setting will flash in the display to
alert you before each change. Important: The
Speed and Incline buttons will not function
during the program.
You must wear the chest pulse sensor to use
the fitness test program.
2
4
Press the Start button or the Speed + button to
start the program.
A moment after the button is pressed, the treadmill will automatically adjust to the first speed and
incline settings of the program. Begin walking on
the treadmill. Note: For the most accurate results,
do not hold the handrails during the fitness test
program.
For the most accurate results, use the fitness test program when you are not feeling tired, when you have not
eaten for at least two hours, and when you have not exercised for at least 24 hours. Follow the steps below to
use the program.
1
Enter your age.
15
4
HOW TO USE A PULSE PROGRAM
If pulse program 1, 2,
or 3 is selected, the
maximum target heart
rate setting of the program will flash in the
display. If desired,
press the increase and
decrease buttons above the Pulse Control button
to change the maximum target heart rate setting
(see EXERCISE INTENSITY on page 30). Note:
If the maximum target heart rate setting is
changed, the intensity level of the entire program
will change.
CAUTION:
If you have heart problems, or if you are over 60 years of age and
have been inactive, do not use the pulse programs. If you are taking medication regularly,
consult your physician to find whether the
medication will affect your exercise heart rate.
Follow the steps below to use a pulse program.
1
Put on the chest pulse sensor.
If pulse program 4 is selected, the target heart
rate setting for the entire program will flash in the
priority display. If desired, press the increase and
decrease buttons above the Pulse Control button
to change the target heart rate setting (see EXERCISE INTENSITY on page 30).
You must wear the chest pulse sensor to use a
pulse program.
2
Insert the key into the console.
See HOW TO TURN ON THE POWER on
page 12.
3
Enter a target heart rate setting.
5
Select one of the pulse programs.
Press the Start button or the Speed + button to
start the program.
A moment after the button is pressed, the treadmill will automatically adjust to the first speed and
incline settings of the program. Hold the handrails
and begin walking.
To select a pulse program, press the Pulse
Control button repeatedly until “PLS1,” “PLS2,”
“PLS3,” or “PLS4” appears in the priority display.
When the first segment ends, all target heart rate
settings will move one column to the left. The target heart rate setting for the second segment will
then be shown in the flashing Current Segment
column.
To stop the program at any time, press the Stop
button. To restart the program, press the Start button or the Speed + button. The walking belt will
begin to move at 2 km/h. When the console compares your heart rate to the target heart rate setting, the speed and/or incline of the treadmill will
automatically change to bring your heart rate
closer to the target heart rate setting.
During all pulse programs, the console will regularly compare your heart rate to the target heart
rate setting. If your heart rate is too far below or
above the target heart rate setting for the current
segment, the speed of the walking belt will automatically increase or decrease to bring your heart
rate closer to the target heart rate setting.
6
See step 5 on page 12.
If the speed or incline setting is too high or too low
at any time during the program, you can adjust the
setting with the Speed or Incline buttons. However,
each time the console compares your heart rate to
the target heart rate setting, the speed of the
treadmill may automatically change to bring your
heart rate closer to the target heart rate setting.
7
8
16
When you are finished exercising, remove the
key from the console.
See step 8 on page 15.
If your pulse is not detected during the program,
the letters “PLS” will flash in the display and the
speed of the treadmill may automatically
decrease. If this occurs, see CHEST PULSE SENSOR TROUBLESHOOTING on page 9.
If pulse program 1, 2,
or 3 is selected, the tarCurrent
get heart rate setting
Segment
for the first segment will
be shown in the flashing Current Segment
column of the matrix.
The target heart rate
settings for the next
several segments will be shown in the columns to
the right. When only three seconds remain in the
first segment of the program, both the Current
Segment column and the column to the right will
flash and a series of tones will sound.
If pulse program 4 is
selected, a pulse
symbol will scroll
across the matrix.
Turn on the fan if desired.
See step 7 on page 13.
Pulse programs 1, 2, and 3 are divided into several one-minute segments. One target heart rate
setting is programmed for each segment. (Note:
The same target heart rate setting may be programmed for two or more consecutive segments.)
Pulse program 4 is divided into 40 one-minute
segments. The same target heart rate setting is
programmed for all segments. Note: For a shorter
workout, simply stop the program before it ends.
If pulse program 1, 2, or 3 is selected, a profile
of the target heart rate settings of the program will
scroll across the matrix (see the drawing above).
Follow your progress with the matrix and the
display.
17
EXPLODED DRAWING—Model No. PETL62705.0
27
26
5
1
96
36
103
95
To identify the parts shown on this EXPLODED DRAWING, see the PART LIST on
page 31 of the user’s manual.
98
97
18
R0805A
99
33
102
32
22
33
23
24
33
33
101
100
99
5
19
66
33
28
93
66
16
15
25
42
5
30
3
10
91
46
6
92
33
5
1
12
104
45
47
18
11
39
38
32
43
28
62
4
41
32
94
49
10
5
69
3
15
48
17
9
5
70
3
11
12
63
6
53
40
19
90
9
3
51
52
58
40
83
7
61
60
25
7
53
55
2
7
90
70
2
91
7
92
33
3
59
54
93
57
83
94
2
2
3
2
EXPLODED DRAWING—Model No. PETL62705.0
R0805A
79
107
29
20
8
8
64
64
34
105
106
29
77
37
3
73
50
35
3
8
64
84
35
13
78
21
33
3
64
44 3
3
32
65
68
3
31
8
3
77
82
3
32
33
83
3
76
31
3
89
110
56
32
82
32
86
44
8
3
83
88
82
83
83
72
108
89
68
71
75
33
112
3
65
67
82
14
3
109
3
81
80
111
85
3
8
87
67
32
82
80
81
82
83
83
74