This manual will show you how to use your FUJIFILM DIGITAL CAMERA
FinePix4700 ZOOM correctly. Please follow the instructions carefully.
BB10959-200 (1)
Warning
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
This symbol is intended to alert the user to
the presence of uninsulated “dangerous
voltage” within the product’s enclosure that
may be of sufficient magnitude to constitute
a risk of electric shock to persons.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The graphical symbols are located on the bottom
of the case.
This symbol is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
For customers in the U.S.A.
FCC Statement
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two
conditions:(1) This device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
2
CAUTION
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference to
radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct
the interference by one or more of the following
measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment
and receiver.
— Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
— Consult the dealer or an experienced radio/TV
technician for help.
You are cautioned that any changes or
modifications not expressly approved in this manual
could void your warranty.
For customers in Canada
CAUTION
This Class B digital apparatus complies with
Canadian ICES-003.
Please read the Safety Notes (➡P.120)
and make sure you understand them
before using the camera.
3
Contents
Preface..................................................................... 6
Camera Features and Accessories..................... 7
Nomenclature ......................................................... 8
1 Getting Ready
ATTACHING THE STRAP ................................... 15
SELECTING THE POWER SUPPLY.................. 16
● Using Batteries................................................. 16
● Using the AC Power Adapter .......................... 18
LOADING AND REMOVING THE SmartMedia™ ...... 19
SWITCHING ON AND OFF ................................. 21
SETTING THE DATE AND TIME ........................ 22
2 Basic Photography
4
TAKING PICTURES(AUTO MODE) ................... 24
● Number of Available Frames .......................... 29
USING AF/AE LOCK ............................................ 30
FRAMING GUIDELINE FUNCTION.................... 32
VIEWING YOUR IMAGES (PLAYBACK) ........... 34
FAST FORWARDING IMAGES .......................... 35
PLAYBACK ZOOM............................................... 36
MULTI-FRAME PLAYBACK ................................ 37
ERASING SINGLE FRAME ................................. 38
USING A TV MONITOR ....................................... 40
3 Advanced Features
ADVANCED FEATURES PHOTOGRAPHY ...... 41
◆Photography mode specifications..................... 41
PHOTOGRAPHY MODE ............................................... 41
3 AUTO ............................................................ 42
7 PORTRAIT ................................................... 42
6 LANDSCAPE ............................................... 42
8 NIGHT SCENE............................................. 43
4 MANUAL....................................................... 44
5 CONTINUOUS SHOOTING ....................... 45
9 MOVIE .......................................................... 47
PHOTOGRAPHY MENU ............................................... 50
G SETTING THE BRIGHTNESS
(EXPOSURE COMPENSATION).................... 51
M FLASH BRIGHTNESS ADJUSTMENT ........ 52
A SETTING THE WHITE BALANCE ............. 52
B SETTING THE SENSITIVITY ..................... 53
C SETTING THE MANUAL FOCUS .............. 54
h PHOTOMETRY ........................................... 55
` SHARPNESS ............................................... 56
W PREVIEW DISPLAY .................................... 57
AUTO BRACKETING .................................. 58
FLASH PHOTOGRAPHY .................................... 59
x Auto flash mode ........................................... 60
Z Red-Eye Reduction ...................................... 60
vForced Flash ................................................... 61
w Night Scenes (Slow Synchro) ...................... 61
a Suppressed Flash ........................................ 62
Y MACRO(CLOSE-UP) PHOTOGRAPHY ....... 63
b SELF-TIMER PHOTOGRAPHY ..................... 64
DIGITAL ZOOM .................................................... 66
4 Advanced Features Playback
ADVANCED PLAYBACK ..................................... 67
◆Playback mode menu ....................................... 67
MOVIE PLAYBACK .............................................. 68
PLAYBACK MENU
L ERASING SINGLE•ALL FRAME/FORMATTING ...... 71
N PLAYBACK (AUTOMATIC PLAYBACK) ....... 73
RESIZE ......................................................... 74
P SETTING AND REMOVING
SINGLE-FRAME PROTECTION ................ 76
P SETTING AND REMOVING
PROTECTION FOR ALL FRAMES............ 78
HOW TO SPECIFY PRINT OPTIONS ............. 80
[ DPOF DATE SETTING ............................... 81
[ DPOF SET FRAME ..................................... 82
[ DPOF REVIEW/CANCEL........................... 86
[ DPOF SET ALL/CANCEL ALL................... 88
U CREATE INDEX .......................................... 90
E
5 Setting
SET-UP MODE ..................................................... 92
SETTING THE IMAGE QUALITY........................ 94
SETTING THE FILE SIZE .................................... 95
FRAME NO. MEMORY ........................................ 96
STARTUP SCREEN............................................. 97
ADJUSTING THE LCD MONITOR BRIGHTNESS
AND THE SPEAKER VOLUME ............................ 99
System Expansion Options ................................. 100
Using the USB Cables and
the Software Included ........................................ 101
Optional Accessories Guide ................................ 103
Explanation of Terms ........................................... 105
Notes on Using Your Camera Correctly ............. 106
Notes on the Power Supply ................................. 107
● Applicable Batteries .......................................... 107
● Notes on the Batteries ...................................... 107
● Notes on Using the Battery Charger ............... 108
● BC-NH Battery Charger Specifications ........... 109
● Notes on Using the AC Power Adapter........... 109
Notes on the SmartMediaTM ................................. 110
Warning Displays ................................................. 112
Troubleshooting.................................................... 115
Specifications ....................................................... 118
Safety Notes ......................................................... 120
EC Declaration of Conformity .............................. 123
1
2
3
4
5
5
Preface
■ Test Shots Prior to Photography
of water and induce vomiting. Then seek medical assistance.
For particularly important photographs (such as weddings and
overseas trips), always take a test photograph to check that the
camera is functioning normally.
● Fuji Photo Film Co., Ltd cannot accept liability for any
incidental losses (such as the costs of photography or the loss
of income from photography) incurred as a result of faults with
this product.
■ Notes on Electrical Interference
■ Notes on Copyright
Images recorded using your digital camera system cannot be
used in ways that infringe copyright laws without the consent of
the owner, unless intended only for personal use. Note that
some restrictions apply to the photographing of stage
performances, entertainments and exhibits, even when
intended purely for personal use. Users are also asked to note
that the transfer of memory cards containing images or data
protected under copyright laws is only permissible within the
restrictions imposed by those copyright laws.
■ Liquid Crystal
6
Camera Features and Accessories
If the LCD monitor or LCD panel is damaged, take particular
care with the liquid crystal in the monitor or panel. If any of the
following situations arise, take the urgent action indicated.
● If liquid crystal comes in contact with your skin
Wipe the area with a cloth and then wash thoroughly with
running water and soap.
● If liquid crystal gets into your eye
Flush the affected eye with clean water for at least 15minutes
and then seek medical assistance.
● If liquid crystal is swallowed
Flush your mouth thoroughly with water. Drink large quantities
Do not use this device in aircraft or hospitals. The use of this
device in an aircraft or hospital can cause malfunctions in the
control devices used in the aircraft or hospital.
Features
■ Explanation of Color Television System
● The newly developed Super CCD which delivers an high
resolution image file with 4.3 million pixels.
● Built-in 3✕ zoom lens with a low-dispersion aspherical lens for
superb optical performance
● Compact and lightweight aluminum-magnesium alloy body
● Quick, responsive operation with 2-second startup and 1
second between shots.
● Fast ISO 200 film speed and built-in automatic flash allow
shooting in a wider range of situations.
● Auto focus with macro function (manual focus also available)
● Automatic shooting modes that can be tailored to subjects in
different photography conditions
● Manual photography mode that allows fine tuning of the
photography settings
● Convenient preview function for quickly checking of your shots
● Smooth digital zoom function (1.88✕ at megapixel resolutions)
and playback zoom function (up to 15✕)
● The Framing Guideline function makes it easy to compose
perfectly balanced shots.
● Continuous shooting function even at maximum resolution.
● Movie shooting function (320 ✕ 240 pixels with sound)
● 2-inch 130,000-pixel low-temperature polysilicon TFT LCD
monitor
● Select your favorite image as the startup screen.
● Dot-matrix LCD panel simplifies camera operation.
● USB connection for quick and easy image data transmission
NTSC :
● Conforms to the new standard for digital camera file
■ Handling Your Digital Camera
This camera contains precision electronic components. To
ensure that images are recorded correctly, do not subject the
camera to impacts or shocks while an image is being recorded.
■ Trademark Information
● IBM
PC/AT is a registered trademark of International Business
Machines Corp. of the USA.
● iMac and Macintosh are registered trademarks of Apple
Computer, Inc.
● Windows is a registered trademark of the Microsoft
Corporation of the U.S. registered in the USA and other
countries.
Windows is an abbreviated term referring to the Microsoft
Windows Operating System.
● SmartMedia is a trademark of Toshiba Corporation.
● Other company or product names are trademarks or registered
trademarks of the respective companies.Trademark
Information
PAL :
National Television System Committee, color
television telecasting specifications adopted mainly in
the U.S.A., Canada and Japan.
Phase Alternation by Line,a color television system
adopted mainly by European countries and China.
Accessories
● SmartMedia
● Hand Strap (1)
(16MB, 3.3V) (1)
Supplied with:
• Anti-static case (1)
• Index label (1)
● A/V Cable (approx. 1.5m
(4.9 ft.), mini-plug (2.5mm
dia.) to pin-plug cable) (1)
● AA-size Nickel Metal
Hydride (Ni-MH) batteries ● Interface Set (1)
HR-3UF (2)
• CD-ROM (1)
• USB Cable (1)
• Quick Start Guide (1)
• Noise suppression core (1)
● Owner’s Manual
(this manual) (1)
● Battery Charger BC-NH(1)
system✽
✽ Design rule for Camera File System.
● Supports DPOF (Digital Print Order Format) for simple print
ordering
7
Nomenclature
✽
Refer to the pages in parentheses for more details.
Viewfinder window
Shutter button
Photography
Mode dial(P.12)
Viewfinder(P.26)
Flash(P.59)
Mode switch(P.12)
POWER button(P.12)
Strap mount(P.15)
Microphone(P.47)
Flash control sensor
Flash pop-up button(P.59)
DISP button(P.32·37)
LCD panel(P.10)
4-direction button(P.10)
MENU/EXE button
Speaker(P.99)
Self-timer lamp(P.65)
Lens/Lens Cover
SHIFT/r button
Viewfinder lamp(P.28)
CANCEL/BACK button
SmartMedia slot cover
release button(P.19)
DIGITAL(USB)
socket(P.102)
A/V OUT
(audio/visual output)
socket(P.40)
SmartMedia slot cover(P.19)
SmartMedia slot(P.19)
Battery cover(P.17)
Tripod mount
LCD monitor
DC IN 3V (power input)
socket(P.18)
8
9
Nomenclature
LCD panel
LCD Display Details
4-direction button
setting display (a)
Mode display
4-direction button
setting display (d)
0 Mode
Photography
Icons are displayed on the LCD panel to help with different camera operations. Use these icons as a
guide to using the 4-direction button.
4-direction button
Up •
Zoom
Telephoto •
Flash
No. of remaining shots
/Remaining time
Down •
Manual •
Auto •
Portrait •
Left •
Right
Wide angle
x Auto •
Red-eye Reduction •
Macro
ON •
OFF
Self-Timer
ON •
OFF
Manual Focus
Moves the focus closer •
Image Quality
FINE •
File Size
2400✕1800 •
Playback
1 Mode
10
Continuous Shooting •
Night Scene
Night Scenes(Slow Synchro) •
4-direction button
setting display (b )
mode, the number of remaining shots or remaining time, the quality setting, resolution, flash setting,
macro setting and self-timer setting.
✽ When the Mode switch, Power button or “SHIFT/r”button is used, the LCD panel will light up orange
for 5 seconds in Photography mode and in green for 5 seconds in Playback mode.
Movie •
Framing Guide
4-direction button
setting display (c)
✽ This panel allows you to check and modify camera settings such as the photography or playback
Setup •
Landscape •
Moves the focus further away
NORMAL •
Still image •
BASIC
1280✕960 •
Movie •
Frame Advance
Previous image •
Playback Zoom
Zoom Up •
Movie Playback
Play/Pause •
Forced Flash
Suppressed flash
640✕480
Zoom/Trimming •
Playback •
Reverse playback•
Paused
Next image
Zoom Down
Reverse playback •
Fast forward •
Rewind •
Stop •
Movie frame advance
Page Advance
Previous page •
Next page
11
Nomenclature
Mode switch
Photography Mode dial
Mode switch
Photography mode
Power button
2
Setup
(➡P.92)
In this mode, you can set the image quality, file size, sharpness, Auto
Power-Off function, frame number memory, buzzer tone, Startup screen,
date and time settings.
9
Movie
(➡P.47)
Allows movies (320✕240 pixels, 10 fps, AVI format with sound) up to 80
seconds long to be shot in the same file.
5
Continuous shooting
(➡P.45)
You can shoot up to 3 frames at intervals of 0.2 seconds. The manual focus
and Auto Bracketing (3 consecutive frames) functions can also be used.
4
Manual
(➡P.44)
Allows you to check your image before it is recorded. In this mode, you
can also specify the settings for Brightness (exposure compensation),
Flash Brightness Adjustment, White Balance, Sensitivity. Manual Focus,
Light Metering Mode, Sharpness and Preview.
Playback mode
Photography Mode dial
Continuous shooting
Movie
Manual
Setup
Auto
Shutter button
Auto
3
(➡P.24·42)
7
Portrait (➡P.42)
6 Landscape (➡P.42)
Night Scene
Portrait
Night Scene
8 (➡P.43)
This is a simple and convenient photography mode in which the camera
automatically controls settings such as the exposure to suit the shooting
conditions. This mode is ideal for general photography where you are not
trying to achieve any particular effect.
Use this mode for shots of people.
Use this mode for shots of distant objects such as landscapes.
Use this mode to shoot pictures at night. You can also use manual focus
in this mode.
Landscape
12
13
Ready
1 Getting
Nomenclature
ATTACHING THE STRAP
Example of LCD Monitor Text Display • Shooting
1
Photography Mode
YMacro photography icon
bSelf-Timer photography icon
Zoom bar
2
Number of remaining shots
oCamera shake warning
p Battery low warning
AF frame
Date
Pass the loop of thin cord on the end of the strap
through the strap mount.
Example of LCD Monitor Text Display • Playback
Then pass the other end of the strap through the
loop of thin cord and pull the strap tight.
1
Playback frame number
Playback mode
p Battery low warning
F Protection
K DPOF
Date
Time
*The above screen shows the NTSC model. The date order differs in the PAL model (day. month. year).
14
Some items are displayed depending on the camera mode and photography conditions.
15
SELECTING THE POWER SUPPLY
Using Batteries
1
2
3
The FinePix4700 ZOOM takes 2 nickel-metal
hydride (Ni-MH) or Ni-Cd batteries. The two
batteries used should both be of the same type.
◆Number of available shots (with fully charged batteries)
The table below provides a guide to the number of shots
that can be taken at normal temperature with 50% flash
use. Note that these figures may vary depending on the
camera’s ambient temperature and the level of battery
charge.
LCD monitor
on
LCD monitor
off
Ni-MH battery HR-3UF
Approx. 80
Approx. 230
Ni-Cd battery KR-3UF
Approx. 50
Approx. 140
Battery Type
◆Notes on the Batteries◆
It is also possible to take some shots using
alkaline batteries if you use the viewfinder
(➡P.24). However, due to the nature of
alkaline batteries, they can only be used for
extremely short periods and they may not
work at all in cold conditions.
● Lithium or manganese batteries should not be
used at all as they emit heat and can damage
the camera.
● Do not use old and new batteries together.
●
16
Load the rechargeable batteries into the battery
charger as indicated on the label.
◆ Batteries that Can Be Charged ◆
AA-size Ni-MH batteries
Fujifilm HR-3UF : 2 (supplied with the camera
or sold separately)
● AA-size Ni-Cd batteries
Fujifilm KR-3UF: 4 (sold separately)
●
! Use only the designated batteries. Batteries other than
●
AA-size Ni-MH or Ni-Cd batteries cannot be recharged
in the BC-NH.
! Attempting to charge batteries other than those specified
●
for use with the charger (such as manganese, alkaline or
lithium batteries) can cause the batteries to burst or leak.
This could result in a fire or injury and consequent
damage to the surroundings.
Plug the charger into a power outlet to begin
charging. Battery charging will be completed in
about 13 hours, but the power lamp remains lit.
Unplug the battery charger from the power outlet
when it is not in use.
Slide the “battery cover” in the direction of the
arrow and open the cover.
! Ni-MH batteries are not fully charged at shipment and
●
batteries. If the camera is left switched on, the
camera settings may revert to the factory default
settings.
! If the AC power adapter has been connected or the
●
batteries have been installed for about half a day or
longer, the camera settings will be retained for about
half a day after the AC power adapter has been
disconnected and the batteries have been removed.
Check the date setting after you replace the
batteries.
must be charged before being used.
! Fully discharged Ni-MH batteries take approximately 12
●
hours (1450 mAh) or 13 hours (1600 mAh) to recharge.
KR-3UF Ni-Cd batteries take approximately 8 hours to
recharge.
! The power lamp remains lit even after charging is
●
completed.
! Shorter charging times can be achieved using the Ni●
MH/Battery Charger BCH-NH (➡P.103).
1
! Do not apply excessive force to the battery cover.
●
! Always switch the camera off when replacing the
●
17
LOADING AND REMOVING THE SmartMedia™
SELECTING THE POWER SUPPLY
4
➀
●
➁
●
Using the AC Power Adapter
SmartMediaTM
■ Only use 3.3V SmartMedia.
MG-4S (4MB), MG-8S (8MB), MG-16S (16MB),
MG-32S (32MB), MG-64S (64MB)
! Take
●
18
care not to drop the batteries when opening
and closing the battery cover.
! See P.107 for notes on using other power supplies.
●
To shoot or play back images without depleting
the battery charge, use the special AC Power
Adapter AC-3V(sold separately).
Check that the camera is switched off and then plug
the AC power adapter connector into the “DC IN 3V
socket” on the camera. Then plug the AC power
adapter into the power outlet.
! You cannot charge the batteries by connecting the AC
●
power adapter.
! The socket-outlet shall installed near the equipment and
●
shall be easily accessible.
! The shapes of the plug and socket-outlet depends on the
●
country of use.
! Using AC power adapters other than the AC-3V could
●
damage the camera.
! See P.109 for more information on the AC power adapter.
●
➀
●
➂
●
➁
●
DC IN 3V Socket
➀ Install the batteries with the correct polarity as
shown.
➁ Close the battery cover as indicated by the
arrow.
Loading the SmartMediaTM
1
➀ Check that the camera is switched off, release
the slot cover lock and open the cover.
the SmartMedia firmly into the
SmartMedia slot as far as it will go.
➂ Close the slot cover.
➁ Push
! Images
●
cannot be recorded or erased if a writeprotect sticker is affixed to the SmartMedia.
! Operation of this camera is only guaranteed when it
●
is used with Fujifilm SmartMedia.
! Some 3.3V SmartMedia are labelled as “3V ” cards.
●
! See P.110 for more information on SmartMedia.
●
! If
●
you open the slot cover while the camera is
switched on, the camera is automatically switched
off to protect the SmartMedia.
! The SmartMedia will not slide fully into the slot if it is
●
inserted facing the wrong way. Be careful not to
apply undue force to the SmartMedia.
19
SWITCHING ON AND OFF
LOADING AND REMOVEING THE SmartMedia™
Removing the SmartMediaTM
1
➀
●
2
2
➁
●
➀ Check
that the indicator in the viewfinder is
green and then switch the camera off.
➁ Release the SmartMedia cover lock as shown
in the figure.
20
1
Never open the SmartMedia slot cover while
the camera is switched on.This could destroy
the image data or damage the SmartMedia
itself.
LCD Panel
LCD Monitor
On
Push the SmartMedia into the slot slightly and
allow it to pop back out. It can then be pulled out
easily.
Press the Power button to switch the camera on
or off. When the camera is switched on, the
viewfinder lamp glows green.
! If you switch the camera on when the Mode switch is
●
set to “ 0 ”, the lens cover opens and the lens
moves out. For this reason, take care to avoid
touching the lens when you switch the camera on.
! Switch the camera on before attempting to use the
●
camera in any way.
! To
●
protect the SmartMedia, always store it in the
special anti-static case.
! See P.80, 100 for information on printing images.
●
! See P.100-102 for information on downloading
●
images to a personal computer.
When the Auto Power Off function is
enabled (➡ P.92), the camera automatically
switches itself off if it is left on and unused
for a few minutes.
Blank
Flashing
On
On
On
Check the battery level warning when you switch
the camera on.
➀The battery is fully charged.
(This icon is only displayed on the LCD panel
for 3 seconds after you switch the camera on.)
➁The battery charge is too low. Fully charged
batteries should be installed as the power will
run out shortly.
➂There is no charge at all in the batteries. The
icon disappears immediately and camera
operation stops. Install fully charged batteries.
! If
●
the date or time shown on the LCD monitor is
blinking, set the date and time. (➡ P.22)
1
21
SETTING THE DATE AND TIME
1
➀
●
➁
●
2
3
➁
●
the Mode switch to “ 0 ” ➁ Set the
Photography Mode dial to“ 2 ”.The SET–UP
screen appears on the LCD monitor.
➀ Set
! See
●
22
P.92 for more information on the items in the
“ 2”(SET–UP) mode menu.
! If the AC power adapter has been connected or the
●
batteries have been installed for about half a day or
longer, the date and time settings will be retained for
about half a day after the AC power adapter has
been disconnected or the batteries have been
removed.
➀Press
4
➀
●
“ b ” on the 4-direction button to select
“DATE/TIME”. ➁Press the “MENU/EXE” button.
Press “ d ” or “ c ” on the 4-direction button to
select the setting (year, month, day, hour or
minute), and use “ a ” and “ b ” to correct the
setting.
! Seconds cannot be specified.
●
! When the displayed time passes
●
“12:00:00”, the
camera automatically switches between AM and PM.
! PAL model : 2000 .01.01.
●
When you have finished setting the date and
time, press the “MENU/EXE” button to confirm
the setting. The SET–UP screen then reappears.
To exit the “ 2 ” (SET-UP) mode, set the
Photography mode dial to any mode other than
the “ 2” mode.
! To
●
set the time precisely, press the “MENU/EXE”
button when the time is at zero seconds.
1
23
Photography
2 Basic
1
➀
●
TAKING PICTURES (AUTO MODE)
➁
●
the Mode switch to “ 0 ” ➁ Set the
Photography Mode dial to “ 3 ”.
To take pictures using the LCD monitor, press
the “ DISP” button to switch the LCD monitor on.
2
3
4
Be careful to ensure that the lens, microphone
and flash control sensor are not obscured by
your hands or the camera strap.
➀ Set
Loop the strap over your wrist, brace your
elbows firmly against your body and hold the
camera with both hands.
2
To zoom in on your subject (
TELE), press
“a” on the 4-direction button. To zoom out (
WIDE), press “ b ”.
! Check that the lens is clean. If it is dirty, clean the
●
! If
●
24
the date/time display on the LCD monitor is
flashing, set the date and time (➡P.22).
! You can photograph subjects at distances of 80 cm
●
(2.6 ft.) to infinity. For subjects closer than 80 cm,
use Macro photography (➡P.63).
lens as described on P.106.
! The image will be blurred if the camera moves when
●
! The lens on the FinePix4700 ZOOM is a 3✕ zoom
●
you take the picture (camera shake).
! When you are shooting in low-light conditions, use
●
the flash (➡ P.59) or a tripod to prevent blurred
images due to camera shake.
lens with a focal range equivalent to 36-108mm on a
35mm camera.
When you switch the camera on, the focal length is
equivalant to 55mm.
! The
●
camera may not be able to take successful
pictures if your fingers or the strap are in the way.
25
TAKING PICTURES (AUTO MODE)
5
6
7
8
AF frame
LCD monitor
AF frame
When you are using the viewfinder to take a
picture at a distance of 0.8 to 1.5 meters (2.6 to
4.8 ft.), only the shaded area in the figure is
photographed.
Using the viewfinder or LCD monitor, frame your
shot so that the subject fills the entire AF (Auto
Focus) frame.
! When
●
! If your subject is not in the center of the picture, use
●
AF lock to take the picture(➡P.30).
26
see in the LCD monitor, you should use the viewfinder.
! If
●
Press the shutter button down half way. The
image is focused when the AF frame on the LCD
monitor becomes smaller and the shutter speed
and aperture setting appear (and the green
viewfinder lamp stops blinking and remains lit).
Viewfinder
! For dimly lit scenes where the subject is difficult to
●
To take the picture, press the shutter button
down fully without lifting your finger off it. The
camera beeps and takes the picture, and the
data is then recorded.
! If the image on the LCD monitor is difficult to see,
●
adjust the monitor brightness.
you press the shutter button down halfway,
the video image on the LCD monitor freezes briefly.
However, this is not the image that is recorded.
! If it is too dark for the camera to focus, move at least
●
1.5 m (4.8 ft.) away from your subject before taking
the picture.
you press the shutter button down fully in one
motion, the shot is taken without the AF frame
changing.
! When you take a picture, the viewfinder lamp lights
●
orange (camera not ready) before switching back to
green to indicate that the camera is again ready for
shooting.
! The viewfinder lamp flashes orange while the flash is
●
charging.
! Since the amount of image data recorded is not fixed
●
and varies depending on the subject (level of image
detail, etc.), the number of available shots may not
decrease after the image is recorded, or may
decrease by 2.
! See P.112 for information on the warning displays.
●
2
27
TAKING PICTURES (AUTO MODE)
◆Viewfinder Lamp Display
Color
Status
Lit
Green
Ready to shoot
AF/AE in progress or camera shake
Flashing warning.Recording to SmartMedia
(the next picture can be taken)
Lit
Orange
Meaning
Image being recorded onto the
SmartMedia (the next picture
cannot be taken)
Flashing Flash charging
● SmartMedia
Red
28
warning
No SmartMedia loaded,
SmartMedia not formatted,
incorrect format, write-protect
sticker used, SmartMedia full,
SmartMedia error
Flashing ●
Battery charging error
● Lens operation error
✽ When the LCD monitor is
switched on, details of the
warning are displayed on the
monitor (➡P.112).
◆Subjects Not Suitable for Autofocus◆
For still image photography (3 , 7 , 6 , 8 ,
4 , 5 ), the number of available shots is
displayed on the LCD panel in the position
shown in the figure at left.
Number of Available Frames
Though the FinePix4700 ZOOM uses an
accurate autofocus mechanism, it may
have difficulty focusing or not be able to
focus at all for the types of subject and
situation listed below. In such cases, the
image may be out of focus.
! See
●
P.94 for information on changing the Quality
setting.
! See P.95 for information on changing the File size
●
setting.
! At shipment, the default settings are NORMAL (for
●
Quality) and 2400 ✕ 1800 (for File Size).
Available frames display
● Very
shiny subjects such as a mirror or
car body.
● Subjects photographed through glass.
● Subjects that do not reflect well, such as
hair or fur.
● Subjects with no substance, such as
smoke or flames.
● When the subject is distant and dark.
● When there is very little contrast between
the subject and the background (such as
white walls or subjects dressed in the
same color as the background).
● When there are objects in front of or
behind the subject (such as an animal in a
cage or a person in front of a tree).
● Subjects moving at high speed.
◆Standard number of shots per SmartMedia
The number of shots that can be recorded onto a SmartMedia card varies slightly depending on the type of subject.
Also, the difference between the standard number of shots and the actual number of available shots increases for
SmartMedia with a higher capacity.
2400✕1800
File Size
1280✕960
640✕480
Quality Mode
FINE
NORMAL
BASIC
FINE
NORMAL
BASIC
FINE
NORMAL
BASIC
Image Data Size
APPROX.
1700KB
APPROX.
803KB
APPROX.
328KB
APPROX.
612KB
APPROX.
312KB
APPROX.
162KB
APPROX.
162KB
APPROX.
87KB
APPROX.
50KB
2
4
9
18
36
4
9
19
38
77
11
23
47
94
189
6
12
25
50
101
12
24
49
99
198
23
47
90
180
362
23
47
90
180
362
44
89
165
331
663
70
141
248
498
996
MG-4S(4MB)
MG-8S(8MB)
MG-16S(16MB)
MG-32S(32MB)
MG-64S(64MB)
2
29
USING AF/AE LOCK
1
2
In a shot with this type of composition, the
subjects (two people in this case) are not in the
AF frame. If the shot is taken at this point, the
subjects will not be in focus.
4
Move the camera slightly so that one of the
subjects in the AF frame.
! The displayed screens are those shown on the LCD
●
monitor.
! See P.24 for information on taking pictures using the
●
LCD monitor.
◆AF (AUTOFOCUS) /AE (AUTOEXPOSURE) LOCK◆
30
3
On the FinePix4700 ZOOM, pressing the shutter button down half way locks the focus and
exposure settings (AF and AE lock). If you want to focus on a subject that is not centered in the
frame or change the picture composition after the exposure is set, you can obtain good results by
changing the composition after the AF and AE settings are locked.
2
Keep the shutter button held down half way (AF
and AE locked) and check that the AF frame is
smaller and that the shutter speed and aperture
settings are displayed (and that the green
viewfinder lamp has stopped blinking and
remains lit).
With the shutter button still held down halfway
(AF lock), move the camera back to the original
image and press the shutter button down fully.
! You can reapply the AF/AE lock as many times as
●
you like before releasing the shutter.
! The AF/AE lock operates in all photography modes
●
and can be used to ensure excellent results.
31
FRAMING GUIDELINE FUNCTION
1
2
➀
●
➁
●
LCD monitor OFF
Scene
LCD monitor ON
Group shot
Framing Guideline displayed
Portrait
Scene
Group Shot
Use this frame when you want
to position your main subject in
center of the frame or when you
want to align your shot with the
horizon.
This is the most effective frame
for monitoring the size and
balance of your subject when
the shot involves motion.
Use this frame when you are
shooting groups of 2 or more
people.
By composing the shot so that
your subjects are as large as
possible within the frame, the
photograph will clearly show
their facial expressions.
Portrait
(Vertical shot frame)
Use this frame for portrait
photography.
Fit the subject's face into one of
the 3 frames to shoot a close-up
portrait (large frame), a head and
shoulders shot (middle frame), or
a half-body shot (small frame).
2
During shooting, when the Photography Mode
dial is set to “3”, “7”, “6” or “8”, the display
on the LCD monitor changes each time you
press the “DISP” button. Press the “DISP button
to display the “Framing Guideline”.
◆ List of Photography Modes/Framing Guideline
32
3
Scene • Group Shot • Portrait
7
Portrait frames only (3 types)
6
Scene • Group Shot
8
Scene • Group Shot
➀You can select an framing guideline by holding
down the “SHIFT/r” button ➁and pressing “a”
on the 4-direction button. The selected framing
guideline serves as a guide to composing your
shot when you are taking pictures using the LCD
monitor.
! The framing guideline is not recorded on the image.
●
! Press the “SHIFT/r” button to view the Camera
●
Operation Guide (an explanation of the operations
available when you press the “SHIFT/r” button).
! The
●
lines in the scene frame roughly
divide the recorded pixels into three equal
parts horizontally and vertically. When the
image is printed, the resulting print may be
shifted slightly from the scene frame.
◆Important◆
Always use the AF/AE lock to compose your picture.
Failing to use the AF/AE lock may result in the image
being out of focus.
33
VIEWING YOUR IMAGES (PLAYBACK)
1
FAST FORWARDING IMAGES
➀
●
2
1
2
➁
●
Normal playback
No text displayed
Set the mode switch to “ 1 ”.
Multi-frame playback
! When
●
you set the mode switch to “ 1 ”, the last
image shot is displayed.
! If image on the LCD monitor is difficult to see, adjust
●
the LCD monitor brightness (➡P.99).
! If you press the “DISP” button once, the text
●
displayed on the LCD monitor disappears.
You can fast forward through the frames by
holding down “ d ” or “ c ” on the 4-direction
button for about 3 seconds during playback.
During fast forward, 3 frames are shown
together in miniature on the LCD monitor. When
you stop fast forward, the image enclosed in the
frame is displayed on the monitor as a single
image.
2
You can use “ c ” and “ d ” on the 4-direction
button to move forward and backward
respectively through your images.
The LCD monitor display changes each time you
press the “DISP” button.
◆Images That Can be Viewed on the FinePix4700 ZOOM◆
34
You can use this camera to view images recorded on an FinePix4700 ZOOM or images recorded
onto a 3.3V SmartMedia using a Fujifilm MX series and DX series digital camera.
! A progress bar is displayed to show the approximate
●
playback position on the SmartMedia.
35
PLAYBACK ZOOM
1
MULTI-FRAME PLAYBACK
2
➁
●
➀
●
1
➀
●
➂
●
➁
●
“ d ” or “ c ” during zooming cancels
zooming and moves to the next image.
➀
●
2
➀ Press the “DISP” button twice during playback.
➁ The 9-shot multi-frame playback screen
Pressing “a” and “ b ” on the 4-direction button
during playback zooms in and out on (enlarges
and reduces) the still image respectively. When
you use this function, a zoom bar is displayed.
●Zoom scales:2400✕1800-dot images: Max15✕
1280✕ 960-dot images: Max 8✕
640✕ 480-dot images: Max 4✕
! Pressing
●
➁
●
If you have taken more than 9 pictures, ➀ you
can quickly skip to the next page of images by
holding down the “SHIFT/r” button, ➁ and
pressing “d”or “ c” on the 4-direction button.
After you have zoomed an image, ➀ you can
move around the image by holding down the
“SHIFT/r” button, ➁ and pressing “a”, “ b ”, “d”
and “ c” on the 4-direction button.
36
2
appears.
“d ” or “ c ” on the 4-direction button to
select a frame. To view the selected frame as a
full-size image, press the “DISP” button again.
➂ Press
! The
●
! Press
●
the “CANCEL / BACK” button to return to
normal unscaled display.
LCD monitor text display disappears after
approximately 3 seconds.
! Playback zoom cannot be used with multi-frame
●
playback.
! The “a” and “ b ” buttons are disabled during multi●
frame playback.
the “SHIFT/r” button displays the onscreen SHIFT CONTROL.
! Multi-frame playback is particularly useful for
●
selecting images for single-frame erase, singleframe protect, Resize, DPOF frame specification or
DPOF confirmation and cancellation.
! Pressing
●
37
ERASING SINGLE FRAME
1
➀
●
➁
●
2
3
4
Press the “MENU/EXE” button to erase the
displayed image. When erasing is complete, the
next image appears and the “ERASE OK?”
message is displayed.
➀ Set the mode switch to “ 1”, ➁ and press the
“MENU/EXE” button to display the Menu screen
on the LCD monitor.
! See
●
38
P.71 for more information on the Playback
mode menu.
! Multi-frame playback is an easy way to select
●
images to be protected.
“c” Select “FRAME” in the ERASE menu and
press the “MENU/EXE” button.
2
Press “d ” or “ c ” on the 4-direction button to
display the image to be erased.
! To
●
! To
●
cancel single-frame erase, press the
“CANCEL/BACK” button to return to the menu. To
exit the menu screen, press the “CANCEL/BACK”
button again.
continue erasing images, repeat the procedure
from step 3 .
! If “ P R O T E C T E D F R A M E ” is displayed, the image
●
protection must be removed to erase the image
(➡P.76).
! If the “
” message is displayed, DPOF
●
is specified. When you press the “MENU/EXE”
button, the image is erased and the DPOF settings
are updated.
DPOF SPECIFIED.
ERASE OK?
39
Features
3 Advanced
USING A TV MONITOR
1
The Advanced Photography section introduces a range of camera functions that you can access by setting the Mode
switch to “0 ”.
2
◆ Photography mode specifications
A/V OUT socket
Video (yellow)
To terminals
Audio (white)
Switch off the camera and TV. Plug the A/V
cable (accessory) into the A/V OUT (audio-visual
output) socket on the camera.
Plug the other end of the cable into the
audio/video input socket on the TV. Then switch
the camera and TV on and take pictures or play
back images as you would normally.
PhotoGraphy
Mode
3
Auto
(➡P.24· 42)
7 Portrait
(➡P.42)
6 Landscape
(➡P.42)
8Night Scene
(➡P.43)
4 Manual
(➡P.44)
! If you connect the A/V cable during playback, you
●
will not hear the sound from the TV.
! If you disconnect or reconnect the A/V cable while
●
40
the power is switched on, the sound may not be
output correctly.
! If there is a power outlet available, connect the
●
AC-3V AC Power Adapter.
ADVANCED FEATURES PHOTOGRAPHY
Accessible menu settings
Factory default
Flash
Photography
(➡P.59)
Macro
photography
(➡P.63)
Self-Timer
Photography
(➡P.64)
-----------------------
------------
O
O
O
-----------------------
------------
O
✕
O
-----------------------
------------
✕
✕
O
Setting the Manual Focus
(➡P.54)
OFF
O
✕
O
Setting the Brightness
Flash Brightness Adjustment
Setting the White Balance
Setting the Sensitivity
Setting the Manual Focus
Metering Mode
Sharpness
Preview Display
(➡P.51)
(➡P.52)
(➡P.52)
(➡P.53)
(➡P.54)
(➡P.55)
(➡P.56)
(➡P.57)
0
0
AUTO
200
OFF
MULTI
0
ON
O
O
O
(➡P.54)
(➡P.58)
OFF
OFF
✕
O
O
------------
✕
✕
✕
5 C o n t i n u o u s Setting the Manual Focus
! If your TV has stereo audio input sockets, plug the
●
cable into the left (white) socket.
! Refer to the instructions provided with your TV for
●
more information on audio and A/V input for your TV.
Shooting
(➡P.45)
9 Movie
(➡P.47)
Auto Bracketing
-----------------------
3
41
PHOTOGRAPHY MODE
AUTO 7 PORTRAIT 6 LANDSCAPE
PHOTOGRAPHY MODE
8 NIGHT SCENE
3 Auto
This is the simplest mode to use and has a wide
range of applications. (➡ P.24)
7 Portrait
This mode is for shots of people. It shows skin
tones beautifully and gives a softer image.
! Macro photography cannot be used in this mode.
●
You can select from 7 photography modes to
suit the type of shot. Select the mode by turning
the Photography Mode dial.
The “7” (Portrait), “6” (Landscape) and “8”
(Night Scene) modes are tailored to particular
types of scene.
6 Landscape
This mode is for shots of scenery during the day.
It gives clear, sharp images of scenery such as
buildings and mountains.
● White balance
The setting used is for outdoor lighting.
● Flash
The flash will automatically be disabled and
cannot be enabled manually.
! Macro photography cannot be used in this mode.
●
42
8 Night Scene
The best mode for shots taken in the evening or
at night. This mode tends to use slower shutter
speeds than Auto mode photography.
● Shutter speed
This is a slow shutter mode with a maximum
time of 3 seconds.
● White balance
The setting used is for outdoor lighting.
● Flash
Forced Flash, red-eye reduction only.
! Because a slow shutter speed is used, a tripod should
●
be used to prevent camera shake.
! Macro photography cannot be used in this mode.
●
When you press the flash pop-up button to use
the flash for clear and detailed shots of people
against a night or evening background, this
mode makes it possible to use the flash with a
slow shutter speed (slow-synchro).
3
! If you do not want to use the flash, press the flash
●
back down to close it.
P.59-62 for more information on flash
photography.
! See
●
43
PHOTOGRAPHY MODE
MANUAL
1
PHOTOGRAPHY MODE
2
CONTINUOUS SHOOTING
1
5 Continuous Shooting
This mode allows you to shoot up to 3
consecutive frames at intervals as short as 0.2
seconds.
4 Manual
Manual mode allows you to take pictures using a
particular set of desired menu settings.
44
! See
●
P.50-58 for more information on the function
settings (photography menu settings).
If you take a picture using the factory default
settings, a preview screen (showing the
photographed image) is displayed on the LCD
monitor. To record the image, press the
“MENU/EXE” button. To discard the image
without recording it, press the “CANCEL/BACK”
button.
! The factory default settings for Manual mode are the
●
same as those for Auto mode except for the preview
screen display.
! See
●
P.54 and 58 for more information on manual
focus and auto bracketing.
! You cannot use the flash in this mode.
●
! The continuous photography speed is the same
●
regardless of the quality and file size settings.
2
When you press the shutter button down
halfway (so that the green viewfinder lamp stops
flashing and stays lit), focusing is completed.
The shot is taken when you press the shutter
button down fully.
3
! The focus and exposure are set when the first frame
●
is shot and do not change for the subsequent
frames.
! The first recorded picture will be displayed in LCD
●
monitor during the continuous shooting.
45
PHOTOGRAPHY MODE
CONTINUOUS SHOOTING
3
4
A
PHOTOGRAPHY MODE
9 MOVIE
1
2
C
B
After the shooting is done, the preview pictures
will be displayed on the monitor in the order that
they are shot, A is first, B is second, C is third.
9 Movie
To record the images, press the “MENU/EXE”
button. The “STORING” message appears on
the LCD monitor while the images are being
recorded onto the SmartMedia. If you do not
want to record the images, press the
“CANCEL/BACK” button.
46
! If you release the shutter button quickly, fewer than 3
●
frames may be shot.
! It takes about 11 seconds to record the 3 frames of
●
image data (NORMAL : 2400 ✕ 1800 pixels).
In this mode, you can shoot up to 80 seconds of
movie with sound at a time (Motion JPEG format
(➡ P.105) at 320 ✕ 240 pixels and 10 frames per
second).
! Because the audio is recorded as you shoot, take
●
care not to cover the microphone with your finger
(➡ P.8).
! Depending on the space available on the
●
SmartMedia, the time that can be recorded in one
movie may be shorter than 80 seconds.
! You cannot switch the LCD monitor off in this mode.
●
When you select movie, the available recording
time is displayed on the LCD panel.
When “STANDBY” then appears on the LCD
monitor, the camera is ready to shoot.
3
◆SmartMedia standard shooting time
SmartMedia
capacity
MG-4S
(4MB)
MG-8S
(8MB)
MG-16S
(16MB)
MG-32S
(32MB)
MG-64S
(64MB)
Available
recording time Approx.22 Approx.45 Approx.90 Approx.182 Approx.364
(sec.)
47
PHOTOGRAPHY MODE
9 MOVIE
3
4
Shooting begins when you press the shutter
button down fully.
In movie photography, the lens is fixed at the
wide-angle setting. Only digital zooming can be
used. The “a” and “ b ” keys on the 4-direction
button control the digital zoom. A zoom bar is
shown on the LCD monitor.
In the top right cornet of the LCD screen is the
bar showing the time remaining for recording.
48
5
6
A "recording time bar" is displayed on the LCD
monitor during shooting.
If you press the shutter button down fully during
shooting, shooting stops and the movie is
recorded onto the SmartMedia.
3
! While
●
shooting a movie, there will not be a beep
sound even if the shutter button is pressed.
! You do not need to hold down the shutter button.
●
! The focus is fixed at 80 cm (2.6 ft.) to infinity.
●
! The focus and white balance are fixed during
●
shooting, but the exposure varies automatically to
suit the scene being shot.
! The “recording time bar” is displayed as a guide to
●
the amount of remaining recording time.When the
recording time bar reaches the right-hand end,
recording automatically ends and the data is
recorded onto the SmartMedia.
! It
●
takes about 11 seconds to record an 80-second
movie (roughly 12 MB) onto a SmartMedia.
! Even if you stop shooting immediately after it has
●
begun, roughly 3 seconds of movie will be recorded.
49
PHOTOGRAPHY MENU
PHOTOGRAPHY MENU
➀,●
➃
●
1
SETTING THE BRIGHTNESS (EXPOSURE COMPENSATION)
◆Subjects for Which Exposure
Adjustment is Particularly Effective◆
2
Positive (+) Compensation
● Copying
➁
●
➂
●
To move to another menu page, press “d ” or
“ c ” on the 4-direction button for the arrows in
the menu (“ ” or “ ”)
➀Press
the “ MENU/EXE” button to display the
menu on the LCD monitor.
➁Use “d” and “ c ” on the 4-direction button to
select the menu setting.
➂Use “a” and “ b ” on the 4-direction button to
change the setting.
➃Press the “ MENU/EXE” button to confirm the
setting.
50
! The available menu settings vary depending on the
●
photography mode. (➡ P.41)
You can set the brightness when the
photography mode is set to “ 4”.
Use the Brightness setting to obtain the optimum
image brightness (exposure) when the subject is
much brighter or darker than the background.
● There
are 11 compensation levels (–1.5 to 1.5
EV in approx. 0.3 EV increments). See P.105
for a definition of EV.
! The
●
Brightness setting is disabled in the following
situations:
·When the flash is used in Auto or Red-eye
Reduction mode
·When dark scenes are shot in Forced Flash mode
of printed text (black characters
on white paper) (+1.5 EV)
● Backlit portraits (+0.6 to +1.5 EV)
● Very bright scenes (such as snowfields)
and highly reflective subjects (+0.9 EV)
● Shots made up predominantly of sky.
(+0.9 EV)
Negative (–) Compensation
● Spotlit
subjects, particularly against dark
backgrounds (–0.6 EV)
● Copying of printed text (white characters
on black paper) (–0.6 EV)
● Scenes with low reflectivity, such as
shots of pine trees or dark foliage (–0.6
EV)
3
✽ Settings given in parentheses are a general
guide.
51
PHOTOGRAPHY MENU
PHOTOGRAPHY MENU
MFLASH BRIGHTNESS ADJUSTMENT
PHOTOGRAPHY MENU
SETTING THE WHITE BALANCE
SETTING THE SENSITIVITY
AUTO : Automatic adjustment
(Shooting to show the ambience of the
light source)
You can set the flash brightness when the
photography mode is set to “ 4”.
Set the Flash Power setting to achieve the
optimum flash brightness when the subject in
the picture is very small or when you are using
close-up flash photography.
● There
are ±2 correction levels (–0.6 to +0.6 in
approx. 0.3 EV increments). See P.105 for a
definition of EV.
You can set the white balance when the
photography mode is set to “ 4”.
Change the white balance setting when you
want to take a picture with the white balance
fixed for the surroundings and lighting when the
picture is taken.
In Auto mode, the correct white balance may not
be obtained for subjects such as close-ups of
people's faces and shots taken under a special
light source. In such situations, select the correct
white balance for the light source. See P.105 for
more information on the white balance.
g
: Shooting outdoors in fine weather
f
: Shooting in shade
l
: Shooting under “Daylight” fluorescent
lamps
m
: Shooting under “Warm White” fluorescent
lamps
n
: Shooting under “Cool White” fluorescent
lamps
q
: Shooting in incandescent light
✽ The white balance setting is ignored when the flash is
used. To achieve the desired effect in your shot,
press the flash back down to suppress flash
operation. (➡P.62)
You can set the sensitivity (film speed) when the
photography mode is set to “4”.
Use this setting when you want to take bright
pictures indoors without using a flash or when
you want to use a fast shutter speed (to prevent
camera shake, etc.).
● Settings:
200 (standard setting), 400, 800
3
! To
●
52
take the picture immediately, press the
“MENU/EXE” button to confirm the white balance
setting.
53
PHOTOGRAPHY MENU
SETTING THE MANUAL FOCUS
1
54
h PHOTOMETRY
◆The light metering modes are
effective for the following subjects◆
2
Press “ d ” on the 4-direction button to move the
focus closer ( ) and “ c ” to move the focus
further ( )away. To check focusing, please use
the LCD monitor.
You can select manual focus when the
photography mode is set to “ 8”, “ 4” or “ 5”.
Use manual focus when the AF function does
not focus the camera or for subjects that are not
suited to AF (➡ P.28).
When manual focusing is set to ON, the “ C”
icon appears on the LCD monitor.
PHOTOGRAPHY MENU
! Because
●
the macro and flash settings cannot be
changed once manual focus is set to ON, set the
macro (➡ P.63) and flash (➡ P.59) settings
beforehand.
You can set the metering when the photography
mode is set to “ 4”.
Use this mode for scenes where the brightness
of the subject and background differ markedly so
that the Multi setting is unlikely to achieve the
desired result.
● AVERAGE: Light metering where an average
value for the entire image is used.
● SPOT
: Light metering where the exposure
is optimized for the center of the
image.
● MULTI
: Light metering where the camera
automatically assesses the scene
and selects the optimum
exposure.
! In "AUTO" mode, the light metering is set to Multi.
●
● AVERAGED
The advantage of this mode is that the
exposure tends not to change for
different compositions or subjects. This
mode is particularly effective for shots of
people wearing black or white clothing
and shots of scenery.
● SPOT
This mode is useful for subjects with
strongly contrasting light and dark areas
where you want to achieve the correct
exposure for a particular feature.
● MULTI
This mode uses automatic scene
recognition to analyze the subject and
obtain the optimum exposure in any
conditions. The "Multi" setting should
normally be used.
3
55
PHOTOGRAPHY MENU
SHARPNESS
You can set the sharpness when the
photography mode is set to “ 4”.
Use this setting to soften or emphasize outlines
or to adjust the image quality.
● The sharpness can be set to ±1 level.
PHOTOGRAPHY MENU
Three levels of sharpness are available.
+ :Emphasizes the outlines.
Best for shots of subjects such as buildings
or text where you want sharp images.
0 :Best for ordinary photography.
Provides edge sharpness that is ideal for
ordinary shots.
--- :Softens the outlines.
Best for shots of subjects such as people,
where a softer image is desirable.
PREVIEW DISPLAY
➀
●
➁
●
You can set the preview display when the
photography mode is set to “ 4”.
Use this setting to specify whether a preview
screen (showing the photographed image) is
displayed after you take a photograph.
ON: The preview screen is displayed and you
can choose whether to record the image.
OFF: The preview screen is not displayed and
the image is automatically recorded.
56
By magnifying the preview picture, checking of
the focusing and details of the picture is
possible.
➀ You can zoom in or out on the image on the
preview screen by pressing “a” or “ b ” on the
4-direction button.
➁ You can move around a zoomed image by
holding down the “ SHIFT/r ” button and
pressing “ d ”, “ c ”, “ a ” or “ b ” on the 4direction button.
3
57
PHOTOGRAPHY MENU
AUTO BRACKETING
FLASH PHOTOGRAPHY
1
A
2
C
B
Auto Bracketing can only be specified when the
photography mode is set to “ 5 ”. Use this
feature to photograph the same image with
different exposure settings. This feature
automatically takes three consecutive pictures
with under, normal, and over exposure. The
amount of the under and over exposure is abe to
be preset.
When you take the picture, the preview screen
appears. A is the overexposed image, B is the
normal image, and C is the underexposed
image. To record the images, press the
“MENU/EXE” button. To discard the images
without recording them, press the “CANCEL
/BACK” button.
● The
three available settings are ±1/3, ±2/3 and
±1 EV.
58
is insufficient space on the SmartMedia for 3 shots,
no picture will be taken.
●
Effective flash range
Wide-angle : 0.2 to 4 m (0.7 ft. to 13.1 ft.)
Telephoto : 0.2 to 3 m (0.7 ft. to 9.8 ft.)
Press “ c ”on the 4-direction button to select the
flash setting. The setting cycles sequentially
through the following: x ➡ Z ➡ v ➡ w
3
! In Auto mode, always pop the flash up and use the
●
automatic flash.
! The
●
! This feature always takes 3 shots. However, if there
●
Press the flash pop-up button to set the flash.
"STORING" message appears on the LCD
monitor while the images are being recorded onto
the SmartMedia.
! It takes about 11 seconds to record the image data
●
(NORMAL: 2400 ✕ 1800 pixels).
! When you pop the flash up, the image shown on the
●
screen may disappear and the screen may go dark
because the flash is charging. In this event, the
viewfinder flashes orange.
! If you do not want to use the flash, press the flash
●
back down to close it.
! If manual focus is set to ON or the flash unit is closed,
●
the flash setting cannot be changed. Set manual focus
to OFF (➡P.54) and pop up the flash.
59
FLASH PHOTOGRAPHY
x Auto flash mode
Use this mode for ordinary photography. The
flash fires automatically as required by the
shooting conditions.
◆Red-Eye Effect◆
60
Z Red-Eye Reduction
Use this mode to ensure that the subject's eyes
appear natural when photographing people in
low-light conditions.
The flash fires a pre-flash just before the picture
is taken and then fires again to take the actual
picture.
When you use the flash to photograph people in low-light conditions, their eyes sometimes appear
red in the picture. This is caused by the light of the flash reflecting off the inside of the eye. Use
Red-Eye Reduction flash mode to effectively minimize the likelihood of the red-eye effect.
Take the following measures also to make Red-Eye Reduction mode more effective:
● Get the subjects to look at the camera.
● Get as close as possible to the subjects.
v Forced Flash
Use this flash mode to photograph backlit
scenes, such as a subject against a window or
in the shade of a tree, or to obtain the correct
colors when you are shooting under lighting
such as fluorescent tubes. In this mode, the
flash fires in bright as well as dark conditions.
w Night Scenes (Slow Synchro)
This is a flash mode that uses a slow shutter speed.
This allows you to take pictures of people at night
that clearly show both your subjects and the
nighttime backdrop.
3
! Because a slow shutter speed is used, a tripod should
●
be used to prevent camera shake.
To take the picture with a background brightly
with a main subject in the night, please use the
“8 ” (Night Scene) photography mode
settings.(➡P.43).
61
Y MACRO (CLOSE-UP) PHOTOGRAPHY
FLASH PHOTOGRAPHY
3
a Suppressed Flash
Pressing the flash unit down suppresses flash
operation. In this mode, the flash never fires.
Use this mode when you are taking pictures in
indoor lighting at distances too great for the flash to
have any effect, such as theater performances or
indoor sporting events. When you use Suppressed
Flash, the Auto White Balance function (➡P.105)
operates so that natural colors are captured along
with the ambience of the available light.
! If you are shooting in Suppressed Flash mode in dark
●
62
conditions, use a tripod to prevent camera shake. If it is
too dark for the camera to focus, move at least 1.5 m
(4.8 ft.) away from your subject before taking the picture.
! See P.28, 113 for information on the camera shake
●
warning.
Press the flash unit down to suppress flash
operation. The “ a” icon appears on the LCD
panel.
Macro photography can be used in the “ 3 ”,
“ 4” and “ 5” photography modes.
In Macro (close-up) mode, you can take pictures
of subjects at distances of between 20 cm
(0.7 ft.) and 80 cm (2.6 ft.) from the camera. Set
the correct flash mode for the shooting
conditions. (➡P.59)
! Because the macro setting cannot be changed when
●
manual focus is set to ON, set manual focus to OFF.
(➡P.54)
! The brightness of the flash can be adjusted (➡P.52)
●
in Manual mode (➡P.44).
! When shooting in dark conditions, use a tripod to
●
prevent era shake.
If you use the viewfinder to take a picture in
Macro mode, the field visible through the
viewfinder does not match the field actually
photographed because the viewfinder and
lens are in different positions. Accordingly,
you should use the LCD monitor to take
pictures in Macro mode.
When the “ ”(MACRO OFF) icon is displayed
on the LCD panel, you can take pictures in
Macro mode by pressing “d” on the 4-direction
button so that “ Y” appears on the LCD monitor.
Pressing “ d ” on the 4-direction button again
cancels Macro mode.
! The LCD monitor is automatically switched on.
●
3
63
b SELF-TIMER PHOTOGRAPHY
1
In the “ 3 ”, “ 7”, “ 6 ”, “ 8 ”, “ 4 ” and “ 5”
modes, holding down the “SHIFT/r ”button
button and pressing “ b ” on the 4-direction
button switches the mode to self-timer
photography.
Repeat the operation to cancel self-timer mode.
! Check that the lens is clean. If it is dirty, clean the
●
64
lens as described on P.106.
! You can also use the Framing Guideline Function.
●
(➡P.32)
2
3
4
The self-timer lamp lights for 5 seconds and
then blinks for 5 seconds, then the camera takes
the picture.
3
Position the AF frame over the subject and
press the shutter button. The camera focuses on
the subject in the frame and self-timer starts to
run.
! You can also use the AF/AE lock (➡P.30).
●
! Be careful not to stand in front of the camera when
●
you press the shutter button as this can cause
focusing or light metering errors.
The time until the shutter releases is shown as a
countdown bar on the LCD monitor and LCD
panel.
Self-timer mode is automatically cancelled after
each shot.
! To stop the self-timer, once it has started running,
●
press the “CANCEL/BACK” button.
! You
●
can check the countdown on the LCD panel
when the LCD monitor is switched off.
65
Features Playback
4 Advanced
DIGITAL ZOOM
ADVANCED PLAYBACK
The Advanced Playback section introduces a
range of playback functions that you can access
by setting the Mode switch to “ 1”.
Zoom bar display
◆Playback mode menu
Playback image
For 1280
When the file size setting is “1280 ✕ 960” or
“640 ✕ 480”, you can use the optical 3✕ zoom
and then the digital zoom by repeatedly pressing
“a”
on the 4-direction button.
However, this is only possible when you are
using the LCD monitor to take pictures.
●
A "zoom bar" is displayed on the LCD monitor,
but the length of the bar varies depending on the
file size setting.
To check the picture in the LCD monitor easier,
press the shutter button halfway.
D
L ERASING SINGLE•ALL FRAMES/
STILL IMAGES
FORMATTING (➡P.38,71)
(➡P.34)
N PLAYBACK(AUTOMATIC PLAYBACK)
(➡P.73)
E RESIZE(➡P.74)
P PROTECTION(➡P.76,78)
K DPOF(Digital Print Order Format)
(➡P.80)
Digital zoom focal distance
1280 ✕ 960 :Approx. 108 to 203 mm
640 ✕ 480 :Approx. 108 to 405 mm
9
! The optical zoom is equivalent to approximately 36●
66
108 mm on a 35 mm camera.
! See P.95 for information on changing the file size
●
setting.
! You
●
Menu options that can be set
For 640
cannot use the digital zoom for resolutions of
2400 ✕ 1800.
! When you switch to digital zoom, the video image on
●
the LCD monitor no longer changes smoothly.
MOVIE
(➡P.68)
DC IN 3V Socket
If you are close to a power outlet, you should
use the AC Power Adapter AC-3V (sold
separately) to avoid any loss of power during still
image or movie playback. (➡ P.18)
4
L ERASING SINGLE•ALL FRAMES/
FORMATTING (➡P.38,71)
U CREATE INDEX(➡P.90)
P PROTECTION(➡P.76,78)
67
MOVIE PLAYBACK
1
2
3
Distinguishing between still images and movies
The “ D ” icon displayed in the middle of the
LCD panel indicates a still image, while the “ 9 ”
icon indicates a movie.
●
You can fast forward “ ” or rewind “ ” the
movie by pressing “ d ” or “ c ” on the 4-direction
button respectively during playback.
Use “d ” and “ c ” on the 4-direction button to
select the movie file. The screen used for movie
appears on the LCD monitor.
To play the movie, press “ b ” on the 4-direction
button. When playback begins, a playback
progress bar and time are displayed.
4
! When you play a movie file, the screen goes dark
●
68
! You can adjust the speaker volume. (➡ P.99)
●
! You can only play back movie files that have been
●
shot on this camera.
! Movie
●
images are displayed slightly smaller than
multi-shot images and fast-forward frames.
temporarily while the camera reads in the image
data.
! Playback automatically stops when the end of the file
●
is reached and the initial screen reappears.
69
MOVIE PLAYBACK
4
PLAYBACK MENU
5
➀
●
ERASING SINGLE• ALL FRAMES / FORMATTING
FRAME
Erases only the selected still image or movie.
1
! This does not erase protected still images or movies.
●
(➡P.76, 78)
ALL
➁
●
Erases all files other than protected still images
or movies.
FORMAT
Press “ b ” to pause movie playback. Press “ b ”
again to resume playback.To stop playback
altogether, press “a”.
Erases all the data and reformats (initializes) the
SmartMedia for use with this camera.
! Formatting
●
also erases protected still images and
movies.
If you press the “MENU/EXE” button, the menu
screen will appear on the LCD monitor.
➀ You
70
can advance frames in a movie by
pressing “ d ” or “ c ” while the movie is paused.
Hold down the button to advance rapidly
through the frames.
➁ You can also view the movie in reverse by
holding down the “SHIFT/r ” button and
pressing the “ b ” button while playback is
paused.
4
! If the “,” or “
●
CARD NOT INITIALIZED ” message
appears, wipe the contact surfaces on the
SmartMedia (the gold-colored area) with a soft, dry
cloth and then re-insert it into the camera.
If this does not resolve the problem, format the card.
! Press the “ CANCEL/BACK” button to exit the menu. 71
●
PLAYBACK MENU
2
ERASING SINGLE • ALL FRAMES / FORMATTING
➀
●
➂
●
3
PLAYBACK MENU
PLAYBACK (AUTOMATIC PLAYBACK)
1
2
➁
●
➀ Press “d” or “ c ” to select “ LERASE”.
➁ Use the “ a ” and “ b ” buttons to select
"FRAME", "ALL" or "FORMAT".
➂ Press the “ MENU/EXE” button.
72
➂
●
➁
●
A confirmation screen appears.
If you are erasing all the frames or formatting the
card, press the “MENU/EXE” button to proceed.
If you are erasing one frame, use the “d” and
“ c ” buttons to select the frame and then press
the “MENU/EXE” button.
! To
●
Formatting erases all of the data on the
SmartMedia.
➀
●
cancel single-frame erase, all-frame erase or
media formatting. press the “CANCEL/BACK” button.
! If the “
” message is displayed, DPOF
●
is specified. When you press the “MENU/EXE”
button, the image is erased.
DPOF SPECIFIED.
ERASE OK?
Press the “MENU/EXE” button to display the
menu on the LCD monitor.
! The Auto Power Off function does not operate during
●
playback.
! Movie playback begins automatically. When playback
●
ends, the next frame appears.
! You cannot use automatic playback to select a
●
movie file.
◆Display Method◆
WIPE1 z…Oblique
WIPE3 |…Mosaic
WIPE2 {…Swirl
➀ Press “d” or “ c ” to select “ N PLAYBACK”.
➁ Use the “a” and “ b ” buttons to select one of
the 3 display methods (wipes).
the “MENU/EXE” button. The image
frames are automatically advanced and
played back.
➂ Press
4
! If you press the “DISP” button once during still image
●
playback, “PLAYBACK” and the playback frame
number are displayed on the LCD monitor.
interrupt playback, press the “CANCEL/BACK”
button.
! To
●
73
PLAYBACK MENU
RESIZE
When you resize an image, a new file is created
containing a smaller amount of data.
Only still images with a size of 2400 ✕ 1800 or
1280 ✕ 960 can be resized.
The resize menu option cannot be selected for
images with a size other than 2400 ✕ 1800 or
1280 ✕ 960 .
1
➀
●
➁
●
“d” or “ c ” to select the image to be
resized.
➁ Press the “MENU/EXE” button to display the
menu on the LCD monitor.
◆Why Resize?◆
74
➀
●
➂
●
3
➁
●
➀ Press
Resizing is extremely convenient when you
want to attach an image file to an e-mail
message.
2
! Movie files cannot be resized.
●
➀ Press “d” or “ c ” to select “ E RESIZE”.
➁ Use the “a ” and “ b ” buttons to select
the
desired image size.
A confirmation screen appears. To proceed,
press the “MENU/EXE” button. The resized
image is recorded as a separate file.
➂ Press the “MENU/EXE” button.
! You can only select sizes that are
●
valid for this
operation.
! Resizing will not proceed if the “ : ” or
●
“ P R O T E C T E D C A R D ” message is displayed. If this
occurs, erase some unwanted images or use a
SmartMedia that is not protected.
4
! If
●
you do not want to resize the image, press the
“CANCEL/BACK” button to return to the menu. To
exit the menu screen, press the “CANCEL/BACK”
button again.
75
PLAYBACK MENU
SETTING AND REMOVING SINGLE-FRAME PROTECTION
1
2
➀
●
➂
●
3
4
➁
●
Press the “MENU/EXE” button to display the
menu on the LCD monitor.
! Protection:
●
76
A setting that prevents images from being
inadvertently erased (➡P.71).
! Multi-frame playback is an easy way to select
●
images to be protected (➡P.37).
➀ Use “d” or “ c ” to select “ P PROTECT”.
➁ Press “a” or “ b ” to select “FRAME”.
➂ Press “MENU/EXE”.
Use “ d ” or “ c ” to select the image to be
protected.
! Movie are protected one photographed item (file) at
●
a time.
When the “MENU/EXE” button is pressed, the
image is protected and the “ F” icon appears on
the right of the screen. To remove the
protection, press the “MENU/EXE” button again.
To finish setting and removing single-frame
protection, press the “CANCEL/BACK” button.
4
! If you do not want to protect any images, press the
●
“CANCEL/BACK” button to return to the menu. To
exit the menu screen, press the “CANCEL/BACK”
button again.
! To protect another image, repeat the procedure from
●
step 3 .
77
PLAYBACK MENU
SETTING AND REMOVING PROTECTION FOR ALL FRAMES
1
2
➀
●
➂
●
3
➁
●
Press the “MENU/EXE” button to display the
menu on the LCD monitor.
➀ Use “d” or “ c ” to select “ P PROTECT”.
➁ Press “a” or “ b ” to select “PROTECT ALL” or
“UNPROTECT ALL”.
➂ Press “MENU/EXE”.
A confirmation screen will appear to proceed,
press the “MENU/EXE” button.
4
! Formatting
●
78
erases all images, including protected
images (➡P.71).
79
HOW TO SPECIFY PRINT OPTIONS
With the FinePix4700 ZOOM, you can order prints using the Digital Print Order Format
(DPOF).
You can use the DPOF to specify the following:
● The frames to be printed and the number of prints for each frame
● Imprinting of the date and time
This section gives a detailed description of how to order your prints with the FinePix4700 ZOOM.
PLAYBACK MENU
1
[ DPOF DATE SETTING
➀
●
➁
●
2
➀
●
➁
●
➂
●
✽ Note that some printers do not support date and time imprinting or specification of the
number of prints.
✽ Note that the warnings shown below may be displayed while you are specifying the
prints.
DPOF SPECIFIED.
ERASE OK?
(➡P.114)
When you erase the image, the DPOF setting for that image are deleted at the same
time
(➡P.114)
If you load a SmartMedia that contains frames specified for printing on another
camera, those print specifications are all reset and replaced by the new print
specifications.
This function allows you to select whether or not
the date of shooting is included on the print.
➀ Set the Mode switch to “ 1”.
➁ Press the “MENU/EXE” button to display the
menu on the LCD monitor.
➂ Press “ c ” to select “ KDPOF”.
(➡P.114)
80
No more than 999 frames can be specified on the same SmartMedia.
! DPOF settings cannot be specified for movie.
●
➀ Use “ b ” to select “H”.
➁ Press “ d c ” to specify “DATE
ON” or “DATE
OFF”. This setting is then valid for all the
prints until the setting is changed.
! Before
●
specifying any other settings, first specify
whether date is to be shown or not.
4
81
PLAYBACK MENU
1
[ DPOF SET FRAME
➀
●
➁
●
2
➀
●
➁
●
3
➀
●
➁
●
4
➀
●
➁
●
➀ Use “ a ” or “ b ” to select “FRAME”.
➁ Press the “MENU/EXE” button.
➀ Use
“ d ” or “ c ” to display the frame to be
specified.
➁ Use “a” or “b ” to specify the number of prints.
If you are not specifying cropping, proceed
to step 6 (➡P.84).
! Always specify the date setting before proceeding to
●
82
other settings.
! If you specify “FRAME” and use cropping, and then
●
specify “SET ALL”, the number of frames specified in
the “FRAME” and cropping settings are cancelled.
! Up to 99 prints can be specified for each frame, and
●
the maximum number of frames for which prints can
be specified on one SmartMedia is 999.
! Multi-frame playback is an easy way to select
●
images to be printed. (➡P.37)
 To specify cropping  3 ~ 5
➀ If you hold down the “SHIFT/r” button ➁ and
press the “MENU/EXE” button, the Crop Settings
screen appears.
! Cropping
●
cannot be specified for 640✕480pixel
images.
! Pressing the “SHIFT/r” button displays the on●
screen corpping quide.
➀ Use“a”and “ b ” to zoom in and out.
➁ You can move the area to be trimmed around
by holding down the “SHIFT/r” button and
pressing “ a ”, “ b ”, “ d ”, and “ c ” on the 4direction button.
4
! The
●
minimum file size for which cropping can be
specified is 640✕480 pixels.
! After trimming, the aspect ratio of the image is 4:3,
●
which is the same as that of the recorded image.
83
PLAYBACK MENU
[ DPOF SET FRAME
 To Continue 
5
6
 To Cancel 
7
To specify prints for another frame, use the “ d ”
and “ c ” buttons to select the frame and then
specify the number of prints.
Check the trimming settings on the LCD monitor
and then press the “MENU/EXE” button to
confirm the settings.
84
When you have completed the settings, always
press the “MENU/EXE” button to confirm the
settings. The total number of prints is displayed on
the LCD monitor and then the menu screen
reappears.
The “K” and the number of prints are displayed for
the specified frames, “ H” is displayed where the
date is specified, and “ J ” is displayed where
cropping is specified.
If you cancel the settings, only the settings for
the currently selected frame are affected.
Previous settings are confirmed.
4
! “TOTAL” shows the total number of prints specified. 85
●
PLAYBACK MENU
1
[ DPOF REVIEW / CANCEL
➀
●
➁
●
➀ Use “a” or “ b ” to select “REVIEW/CANCEL”.
➁ Press the “MENU/EXE” button.
2
You can confirm the settings for only those
frames with a specified number of prints by
pressing “d” or “ c ”. The settings for each frame
are displayed on the right of the screen.
! Multi-frame
●
86
playback is an easy way to select
images (➡P.37).
! If you do not want to check or delete the DPOF
●
settings, press the “CANCEL/BACK” button to return
to the menu. To exit the menu screen, press the
“CANCEL/BACK” button again.
3
To delete the print setting, display the image for
which the setting is to be deleted and then press
the “MENU/EXE” button. When the print setting
has been deleted, the next image appears with
the “SET OK?” message displayed.
4
! To delete further print settings, repeat the procedure
●
from step 2 .
! If all the print specifications are cancelled, the “TOTAL”
●
display reverts to “00000” and the background turns
black.
87
PLAYBACK MENU
1
[ DPOF SET ALL / CANCEL ALL
➀
●
➁
●
2
➀
●
➁
●
3
The total number of prints is displayed on the
LCD monitor and then the menu screen
reappears.
➀ Use
“a” or “ b ” to select “SET ALL/CANCEL
ALL”.
➁ Press the “MENU/EXE” button.
88
➀ Use
“ d ” or “ c ” to select “SET ALL” or
“CANCEL ALL”.
➁ Press sthe “MENU/EXE” button to set the
selected option.
! “SET ALL” specifies 1 print for all the images.
●
! The SET FRAME specifications and cropping
●
settings are cancelled.
! Prints can be specified for up to 999 frames on the
●
same card. If you specify more than 999 frames, the
“
” warning appears(➡P.114).
! “TOTAL” shows the total number of prints specified.
●
! If you cancel all of the frames, the “TOTAL” display
●
reverts to “00000”. The frames also remain
protected.
4
89
PLAYBACK MENU
CREATE INDEX
Index creation can only be specified when there
are image files selected.
This feature creates index images which allow
you to view the content of a movie file without
playing it back.
To create the index, the function selects 25
image frames from the movie file at regular
intervals and then saves them in rows as a
single image (2400 ✕ 1800).
1
➀
●
➁
●
➀ Use “d” or “ c ” to select the movie file.
➁ Press the “MENU/EXE” button to display
the
2
➀
●
➀ Use “d” or “ c ” to select “U INDEX”.
➁ Press the “MENU/EXE” button.
➁
●
3
The index preview screen appears. To record
the index, press the “MENU/EXE” button.
4
menu.
! If
●
90
! The interval between the automatically selected frames
●
varies depending on the movie recording time.
you do not want to record the index, press the
“CANCEL/BACK” button to return to the menu. To
exit the menu screen, press the “CANCEL/BACK”
button again.
91
5 Setting
Settings
SET-UP MODE
Factory default
Explanation
NORMAL
Sets the compression ratio for recording. Can be set as
described on P.94.
2400✕1800
Sets the number of pixels recorded (image file size).
Can be set as described on P.95.
2 MIN/5 MIN/NO
2 MIN
Use this function to specify whether the camera is
automatically switched off if the camera is left unused.
Note that the Auto Power Off function does not operate
during automatic playback (Auto Play) or when a USB
connection is active.
FRAME NO.
RENEW/CONT.
RENEW
Specifies whether the Frame No. Memory function is
used (➡P.96).
BEEP
HIGH/LOW/OFF
HIGH
Sets the volume of the tone emitted when the camera is
used.
QUALITY
Display
FINE/NORMAL/BASIC
2400✕1800/
FILE SIZE
1280✕960/
640✕480
AUTO POWER
OFF
STARTUP
SCREEN
92
The table below explains the camera setting
DATE / TIME
ON/OFF/SET[EXE]
SET
OFF
–––
Selects whether a registered screen is displayed when
the camera is switched on. See P.97 for information on
how to register a screen image.
✽ “ON” cannot be selected if no screen has been
registered.
Sets the date and time (➡P.22).
1
➀
●
➁
●
2
➀
●
➁
●
➀Press “a” or “ b ” to select a setting.
➁Use “d” or “ c ” to change the settings.
➀ Set the Mode switch to “0”.
➁ Set the Photography mode
dial to “ 2 ” to
display the SET-UP screen.
5
! Always
●
switch the camera off when you are
replacing the batteries. If you open the battery cover
or disconnect the AC power adapter without
switching the camera off, all the camera settings
may revert to the factory default values.
The quality setting (➡ P.94) and resolution
setting (➡ P.95) can be specified during
shooting.
93
SETTING THE IMAGE QUALITY
You can select any of 3 image quality (recorded
image compression ratio) settings as required.
The number of shots available varies depending
on the image quality. See P.29 for information
on the number of shots available for each type
of SmartMedia.
Select [FINE] for better image quality, and
[BASIC] to fit more shots on the SmartMedia.
In most cases, the [ NORMAL ] setting provides
suitable image quality.
94
SETTING THE FILE SIZE
➁
●
➀
●
You can select 3 different file size (pixel count)
settings as required. The number of shots
available varies depending on the file size. See
P.29 for information on the standard number of
shots available for each type of SmartMedia.
✕ 1800 pixels
✕ 960 pixels
640 ✕ 480 pixels
● 2400 : 2,400
➀
●
➁
●
● 1280 : 1,280
●
640 :
➀By holding down the “SHIFT/r” button ➁ and
press the “ c ” on the 4-direction button, you can
select from 3 levels of image quality (FINE,
NORMAL, or BASIC). The new setting is
displayed on the LCD panel.
➀By holding down the “SHIFT/r” button ➁and
pressing “ d ” on the 4-direction button, you can
select “2400”, “1280” or “640” as the resolution
(number of pixels). The new setting is displayed
on the LCD panel.
! This setting can be changed when the Mode switch
●
! This setting can be changed when the Mode switch
●
is set to “ 0” and the Photography Mode dial is set
to “ 3”, “ 7”, “ 6”, “ 8”, “ 4” or “ 5”.
is set to “ 0” and the Photography Mode dial is set
to “ 3”, “ 7”, “ 6”, “ 8”, “ 4” or “ 5”.
5
95
FRAME NO.MEMORY
STARTUP SCREEN
1
A
➀
●
2
➀
●
➁
●
Directory no.
File number
Frame number
B
✽ Formatted SmartMedia used for both A and B.
Setting this function to “CONT” makes file
management easier as it ensures that file names
are not duplicated when images are downloaded to
a PC.
RENEW : Pictures are stored on each
SmartMedia beginning with a file
number “0001”.
CONT
: Pictures are stored beginning from
the highest file number stored on the
last SmartMedia used.
! If the SmartMedia already contains image files with
●
96
file numbers higher than the highest file number on
the last SmartMedia, images are stored beginning
from the highest file number on the current
SmartMedia.
➁
●
You can check the file number by viewing the
image. The last 4 digits of the 7-digit number in
the top right corner of the screen are the file
numbers, while the first 3 digits show the
directory number.
! When
●
you change the SmartMedia, always switch
the camera off before you open the SmartMedia slot
cover. If you open the slot cover without switching
the camera off, the frame number memory will not
function.
! File numbers run from 0001 to 9999. Once 9999 is
●
exceeded, the directory number goes up by 1. The
maximum number is 999-9999.
! If you switch the Frame No. Memory function off, the
●
highest file number stored by the function is reset.
! The displayed frame number may differ for images
●
photographed on other cameras.
You can register any photographed image as
your startup screen.
➀ In “STARTUP SCREEN” in the SET-UP
menu, use “d” or “ c ” to select “SET EXE”.
➁ Press the “ MENU/EXE” button to begin
startup screen registration.
! The “ON” setting can only be selected if you have
●
registered a screen.
➀ In
the registration selection screen, use “ d ”
or “ c ” to select the image.
➁ Once you have selected the desired image,
press the “MENU/EXE” button.
! Images to be registered must be Exif format images
●
with a size of 2400 ✕ 1800, 1280 ✕ 960 or 640 ✕ 480.
Movie files are not displayed for selection as
registered images.
! If you do not want to record the image, press the
●
“CANCEL/BACK” button.
5
97
ADJUSTING THE LCD MONITOR BRIGHTNESS AND THE SPEAKER VOLUME
STARTUP SCREEN
3
1
SET ?
If you set “STARTUP SCREEN” in the SET-UP
menu to ON, the registered image is displayed
when you switch the camera on.
98
a new image is registered, the previously
registered image is erased.
! The
●
quality of the displayed startup screen differs
from that of the original image.
2
➀
●
➁
●
➀Press “d” and “ c ” on the 4-direction button to
➀If you hold down the “SHIFT/r” button ➁and
press the “DISP” button, the “adjustment bar” is
displayed.
A registration confirmation screen appears. To
register the current selection, press the
“MENU/EXE” button.
! When
●
➀
●
➁
●
●Adjusting the BRIGHTNESS
You can only adjust the brightness when the Mode
switch is set to either “ 0” or “ 1”. However, when
the Mode switch is set to “ 0”, the brightness cannot
be adjusted if the Mode dial is set to “ 2”.
●Adjusting the VOLUME
The speaker volume can only be adjusted when the
Mode switch is set to “ 1 ” and a movie file is
selected.
adjust the LCD monitor brightness or the
speaker volume. Use “a ” and “ b ” on the 4direction button to switch between brightness
and volume. ➁Press the “MENU/EXE” button to
confirm the setting.
! If movie playback is in progress, playback is paused.
●
! The settings cannot be changed if the LCD monitor
●
5
is switched off.
! To exit this procedure without changing the settings,
●
press the “CANCEL/BACK” button.
99
System Expansion Options
Using the USB Cables and the Software lncluded
By using the FinePix4700 ZOOM together with other optional Fujifilm products, your system can be
expanded to fill a wide range of uses. See P.101 to 104 for details.
1
➀
●
➁
●
TV monitor
(commercially available)
FinePix4700 ZOOM
Digital Camera
Audio/Visual output
SmartMedia
(USB)
Floppy Disk Adapter (FlashPath)
Use the enclosed cable to connect the camera
to your PC and download image data from the
camera to your hard disk. However, writing data
from your PC will not be possible.
(Floppy disk drive)
(PC card slot)
and set the Mode
switch to “1”.
(SCSI)
PC CARD
ADAPTER
PC Card Adapter
➀ Insert the SmartMedia.
➁ Switch the camera on
PC Card
Reader
(USB)
Personal Computer
(commercially available)
! The Auto Power Off function does not operate when
●
(USB)
Image Memory Card Reader
100
Digital Photo Printer
the camera is connected to a PC.
is best to use AC Power Adapter AC-3V (sold
separately) for this operation. Power loss during data
transmission will prevent the image data from being
downloaded correctly.(➡P.18)
! It
●
101
Using the USB Cables and the Software lncluded
2
➀
●
➁
●
Optional Accessories Guide
The optional accessories (sold separately) can make taking pictures with the FinePix4700 ZOOM even
easier. For information on how to attach and use the accessories, refer to the instructions provided with the
accessory used.
3
●
DIGITAL(USB)
Socket
When the viewfinder lamp is orange, data
access is in progress (data is being downloaded
from the SmartMedia). Never open the slot cover
or disconnect the cable during data access as
this could prevent data being transferred
correctly or cause the camera to malfunction.
These are SmartMedia cards sold separately. Use the 5 types listed below.
● MG-4S : 4MB, 3.3V
● MG-8S : 8MB, 3.3V
● MG-16S
: 16MB, 3.3V
● MG-32S : 32MB, 3.3V
● MG-64S : 64MB, 3.3V
✽ Some 3.3V SmartMedia are labelled as “3V” or “ID” cards.
●
✽ The Shapes of the AC power adapter, the plug and socket outlet depend on the country.
●
➀ Plug the small pin on the special cable into the
Digital (USB) socket on the camera, and ➁ plug
the other end of the cable into the USB port on the
PC. When you switch the PC on, “t” appears on
the LCD panel.
102
! Use only the special cable provided.
●
! Refer to the Instructions provided with the USB Interface
●
Set for information on installing the software.
◆Changing SmartMedia◆
●
●
AC Power Adapter AC-3V
Use the AC-3V when taking pictures for a long period of time or when the
FinePix4700 is connected to a personal computer.
! Depending on the hardware and software settings,
●
your PC may be unable to recognize the
SmartMedia after it has been replaced. If this occurs,
switch the camera off and then on again.
SmartMediaTM
Fujifilm Rechargeable Battery 2HR-3UF
The 2HR-3UF includes 2 pieces of high-capacity AA-size Nickel Metal Hydride
batteries.
●
Fujifilm Rechargeable Battery 4KR-3UF
The 4KR-3UF includes 4 pieces of high-capacity AA-size Ni-Cd batteries.
Windows: Check that data access is not in
progress and then change the SmartMedia.
Macintosh: Drag the removable disk icon
from the desktop and drop it in the Trash.
When “REMOVE OK” appears on the LCD
panel, change the SmartMedia.
●
Fujifilm Battery charger with Battery BK-NH (AC 220V only)
The BK-NH includes the quick battery charger BCH-NH and 2 Ni-MH batteries.
The BCH-NH can charge 2 Ni-MH batteries in approximately 110 minutes.
Up to 4 Ni-MH or Ni-Cd batteries can be charged simultaneously.
103
Explanation of Terms
Optional Accessories Guide
AF/AE Lock:
●
Floppy Disk Adapter (FlashPath)
This adapter is the same size and shape as a 3.5-inch floppy disk. You can copy
the images on a SmartMedia to your PC simply by loading the SmartMedia into
the floppy disk adapter and then inserting the adapter into your floppy disk drive.
Compatible OS
FD-A1/A1S/A1N
FD-A2
●
Windows95/98, NT 4.0
Macintosh
Compatible SmartMedia
5V/3.3V, 2MB to 32MB
5V/3.3V, 2MB to 64MB
PC Card Adapter
The PC Card Adapter allows the SmartMedia to be used as a PC Card Standard
ATA-compliant (PCMCIA 2.1) PC card (Type II).
● PC-AD2 : Compatible with SmartMedia of 5V/3.3V, 2MB to 8MB.
● PC-AD3 : Compatible with SmartMedia of 5V/3.3V, 2MB to 64MB.
●
SM-R1/R2 Image Memory Card Reader
The SM-R1/R2 allows images to very easily be read and written from an image
memory card (SmartMedia) to a personal computer. Its USB interface provides
high-speed data transmission.
●
●
104
Windows98 or Power Macintosh with USB interface.
SC-FX1
Special camera case in genuine leather.
This case can be used when carrying the camera to protect it from dust, dirt and
mild impacts.
PC CARD
ADAPTER
On the FinePix4700 ZOOM, pressing the shutter button down half way locks the focus and exposure
settings (AF and AE lock). If you want to focus on a subject that is not centered in the frame or change
the picture composition after the exposure is set, you can obtain good results by changing the
composition after the AF and AE settings are locked.
Auto Power Off Function: If the camera is not used in any way for two minutes or more, the Auto Power Off function switches the
camera off. This is to prevent battery depletion and to avoid wasting power when the camera is
connected to the AC power adapter.The function can be set to either 2 minutes or 5 minutes on this
camera.
● The Auto Power Off function does not operate in PC mode, during automatic playback, or if it is
disabled during setup.
DPOF:
Digital Print Order Format
DPOF is a format used for recording information on a storage media (image memory card, etc.) that
allows you to specify which of the frames shot using a digital camera are printed and how many prints
are made of each image.
EV:
A number that denotes exposure. The EV is determined by the brightness of the subject and sensitivity
(speed) of the film or CCD. The number is larger for bright subjects and smaller for dark subjects. As
the brightness of the subject changes, a digital camera maintains the amount of light hitting the CCD
at a constant level by adjusting the aperture and shutter speed.
When the amount of light striking the CCD doubles, the EV increases by 1. Likewise, when the light is
halved, the EV decreases by 1.
JPEG:
Joint Photographics Experts Group
A file format used for compressing and saving color images. The compression ratio can be selected,
but the higher the compression ratio, the poorer the quality of the expanded image.
Motion JPEG:
A type of AVI (Audio Video Interleave) file format that handles images and sound as a single file.
Images in the file are recorded in JPEG format. Motion JPEG can be played back by QuickTime 2.0 or
later.
PC Card:
A generic term for cards that meet the PC Card Standard.
PC Card Standard:
A standard for PC cards determined by the PCMCIA.
PCMCIA:
Personal Computer Memory Card International Association (US).
White Balance:
Whatever the kind of the light, the human eye adapts to it so that a white object still looks white. On
the other hand, devices such as digital cameras see a white subject as white by first adjusting the
color balance to suit the color of the ambient light around the subject. This adjustment is called
matching the white balance. A function that automatically matches the white balance is called
an Automatic White Balance function.
105
Notes on Using Your Camera Correctly
Be sure to read this information in conjunction with before you use this product “Safety Notes”
(➡P.120) to ensure that you use your camera correctly.
■ Places to Avoid
■ When the Camera is Unused for Long Periods
Do not store or use the camera in the following types of
locations:
● Very humid, dirty or dusty places
● In direct sunlight or in places subject to extreme
temperature rises, such as in a closed car in summer.
Extremely cold places
● Places subject to strong vibrations
● Places affected by smoke or steam
● Places subject to strong magnetic fields (such as places
near motors, transformers or magnets)
● For long periods in contact with chemicals such as
pesticides or next to rubber or vinyl products
If you do not intend to use the camera for a long period of
time, remove the batteries and the SmartMedia card before
storing the camera.
■ Do not expose the camera to sand.
The FinePix4700 ZOOM is particularly and adversely
affected by sand. In sandy locations such as beaches or
deserts, or in locations where there is wind borne sand,
ensure that the camera is not exposed to sand. This can
cause faults that may be irreparable.
■ Notes on Condensation
106
If the camera is carried suddenly from a cold location into a
warm place, water droplets (condensation) may form on
the inside of the camera or on the lens. When this occurs,
switch the camera off and wait an hour before using the
camera. Condensation may also form on the SmartMedia
card. In this event, remove the SmartMedia and wait a
short time before using it again.
■ Cleaning Your Camera
●
●
●
Use a blower brush to remove dust from the lens and
LCD surface and then wipe lightly with a soft, dry cloth. If
any soiling remains, apply a small amount of lens
cleaning liquid to a piece of Fujifilm lens cleaning paper
and wipe gently.
Do not scratch hard objects against the lens, LCD
monitor screen or viewfinder as these surfaces are
easily damaged.
Clean the body of the camera with a soft dry cloth. Do
not use volatile substances such as thinners, benzine or
insecticide, as these may react with camera body and
cause deformation or remove the coating.
■ Using the Camera Overseas
When travelling overseas, do not place your camera in the
check-in baggage. Baggage handling at airports may
subject baggage to violent shocks, and the camera may be
damaged internally even when no external damage is
visible.
Notes on the Power Supply
Applicable Batteries
Use AA-size nickel-metal hydride (Ni-MH) or Ni-Cd
batteries in this camera.
AA-size lithium or manganese batteries cannot be used
as they emit heat and can cause camera faults or
damage.
● The capacities of alkaline batteries vary between brands
and the life of the batteries (the time for which they
provide power) may be very short. You should also
switch the LCD monitor off if you are using alkaline
batteries.
●
Notes on the Batteries
Incorrect use of the batteries could cause them to leak,
become hot, ignite or burst. Always observe the
precautions given below.
● Do not heat the batteries or throw them into a fire.
● Do not carry or store a battery with metal objects such as
necklaces or hairpins that could come into contact with
the metal positive and negative poles of the battery.
● Do not expose the batteries to fresh or sea water, and
take particular care to keep the terminals dry.
● Do not attempt to deform, disassemble or modify the
batteries.
● Do not attempt to peel off or cut the battery casing.
● Do not drop, strike or otherwise subject the batteries to
strong impacts.
● Do not use batteries that are leaking, deformed,
discolored or exhibit any other obvious abnormality.
Do not store batteries in very warm or moist locations.
● Keep the batteries out of the reach of babies and small
children.
● When loading the batteries in the camera, ensure that the
battery polarity ( and ) is as indicated on the camera.
● Do not use new batteries together with used batteries. In
the case of rechargeable batteries, do not use charged
and discharged batteries together. Do not use batteries
of different types or brands together.
● If you do not intend to use the camera for a long period of
time, remove the batteries from the camera. (Note that if
the camera is left with the batteries removed, the time
and date settings are cleared.)
● The batteries may feel warm immediately after being
used. Before removing the batteries, switch the camera
off and wait until the batteries cool down.
● When replacing the batteries, always fit 4 new batteries.
Here, ‘new batteries’ refers to either recently purchased
unused alkaline batteries, or Ni-Cd or Ni-MH (nickel metal
hydride) batteries that have recently been fully recharged
together.
● Battery performance deteriorates at low temperatures
(+10°C or below) and the time for which they can be used
shortens. This is particularly true of alkaline batteries. In cold
conditions, put the batteries in your pocket or a similar place
to warm them before loading them into the camera. If you
use a body warmer to warm the batteries, ensure that they
are not in direct contact with the warmer.
●
107
Notes on the Power Supply
●
If any liquid at all leaks from the batteries, wipe the battery
compartment thoroughly and then load new batteries.
If any battery fluid comes into contact with your hands or
clothing, flush the area thoroughly with water. Note that battery
fluid can cause loss of eyesight if it gets in your eyes. If this
occurs, do not rub your eyes. Flush the fluid out with clean water
and contact your physician for treatment.
●
■ Disposing of Batteries
When disposing of batteries, do so in accordance with your
local waste disposal regulations.
Notes on Using the Battery Charger
■ Notes on Small Rechargeable Batteries (Ni-MH
or Ni-Cd batteries)
●
●
●
●
●
108
Always use the special battery charger to charge AA-size
Ni-MH or Ni-Cd batteries. Charge the batteries as
described in the instructions provided with the battery
charger.
Do not use the battery charger to charge batteries other
than those specified for use with the charger.
Note that the batteries may feel warm immediately after
being charged.
Ni-MH and Ni-Cd batteries are not charged at shipment.
Be sure to charge the batteries before using them.
The camera mechanism is such that it draws a minute
amount of current even when the camera is switched off.
Take particular care not to leave Ni-MH or Ni-Cd
batteries in the camera for a long period of time as they
can become excessively discharged and no longer be
useable even when charged.
Ni-MH and Ni-Cd batteries self-discharge even when not
used. Always charge Ni-MH and Ni-Cd batteries before
using them. If the time for which a battery provides power
shortens markedly when it has been correctly charged,
this indicates that the battery has reached the end of its
effective life and should be replaced.
Soiling (fingerprints, etc) on the terminals of NiMH
batteries can greatly reduce the number of available
shots. When this occurs, clean the terminals carefully
with a soft dry cloth. Then use up the remaining charge
in the batteries and recharge them.
●
●
●
●
●
Rechargeable batteries and the battery charger itself will
become warm due to the power stored inside the
batteries. This is normal and does not indicate a fault.
Wherever possible, use the battery charger in a wellventilated location.
There may be vibration noises from inside the battery
charger during use. This is normal and does not indicate
a fault.
Do not use the battery charger to recharge batteries
other than Fujifilm HR-AA NiMH batteries or Fujifilm KRAA Ni-Cd batteries.
The battery charger could cause interference if placed
close to a radio during charging. In this event, move the
radio and charger further apart.
Do not touch the connections or contact points on
rechargeable batteries with other metal objects as this
can cause a short circuit.
●
●
Do not leave the battery charger in the following
locations.
Locations subject to strong vibrations, in very dusty
locations, or in locations with very high humidity or high
temperatures, such as close to a heating appliance or in
direct sunlight.
The battery charger accepts input voltages of 100-240 V
AC at 50 or 60 Hz and can be used outside Japan.
However, because the shapes of power sockets vary by
country and by region, an appropriate plug adapter is
also required for each country. Consult your travel agent
for details.
BC-NH Battery Charger Specifications
Rated input
Input capacity
Rated output
Applicable
batteries
100-240 V AC, 50/60 Hz
4 VA at 100 V AC, 5VA at 240 V AC
1.2 V DC, 130 mA x 2
FUJIFILM AA-size NiMH 1450
FUJIFILM AA-size NiMH 1600
FUJIFILM AA-size Ni-Cd 1000
Charging FUJIFILM AA-size NiMH 1500: Approx. 12 hours
time
FUJIFILM AA-size NiMH 1600: Approx 13 hours
FUJIFILM AA-size Ni-Cd High Power 1000: Approx. 8 hours
Dimensions 86mm ✕ 68mm ✕ 24.6mm (L ✕ W ✕ D)
Weight
Approx. 80g (excluding batteries)
0°C to +40°C
Operating
temperatures
Notes on Using the AC Power Adapter
Always use the AC-3V AC Power Adapter AC-3V (sold
separately) with the FinePix4700 ZOOM Digital Camera.
The use of an AC power adapter other than the AC-3V
could result in damage to your camera.
● Ensure that you do not touch the contact areas on the
AC power adapter against any other metal object as this
could cause a short circuit.
● Do not plug the AC power adapter into the DIGITAL
socket as this could damage your camera.
● Do not plug in the AC power adapter while you are
operating the camera using batteries. Switch the camera
off first.
● Do not load the batteries while you are operating the
camera using the AC power adapter. Switch the camera
off first.
● If you disconnect the AC power adapter when there are
no batteries in the camera, the date and time settings will
be lost and must be reset.
109
Notes on the SmartMedia™
■ SmartMedia
The SmartMedia card supplied with your
FinePix4700 ZOOM camera is a new image recording
medium developed especially for use in digital
cameras. Each SmartMedia card contains a built-in
semiconductor memory chip (NAND flash memory)
which is used for storing digital image data.
Because the data is stored electronically, the stored
image data can be erased from the card and new data
recorded.
■ SmartMedia with IDs
The SmartMedia ID is a SmartMedia that has an
individually assigned identification number. SmartMedia
ID cards can be used with devices that use ID numbers
for copyright protection or other purposes. This camera
accepts SmartMedia ID cards in the same way as
conventional SmartMedia cards.
■ Storing Data
110
In the situations listed below, recorded data may be
erased (destroyed). Please note that Fuji Photo Film
Co., Ltd. accepts no responsibility whatsoever for the
loss (destruction) of recorded data.
✽When the SmartMedia is used incorrectly by the
owner or a third party
✽When the SmartMedia is exposed to static electricity
or electrical noise
✽When the SmartMedia cover is opened or the
SmartMedia removed and the camera is then
switched off during data recording, during data
erasing (SmartMedia formatting) or during frame
advance when images are being played back.
Back up important data onto another medium (MO
disk, floppy disk, hard disk, etc.).
■ Notes on Handling SmartMedia
● When
inserting the card into the camera, hold the
SmartMedia straight as you push it in.
● Never remove the SmartMedia or switch the camera
off during data recording, during data erasing
(SmartMedia formatting) or during frame advance
when images are being played back. These actions
could result in damage to the SmartMedia.
● Use only the SmartMedia specified for use with the
FinePix4700 ZOOM. The use of other SmartMedia
could damage the camera.
● SmartMedia are precision electronic devices. Do not
bend, drop, or subject SmartMedia to excessive
shocks.
● Do not use or store SmartMedia in environments
likely to be affected by strong static electricity or
electrical noise.
● Do not use or store SmartMedia in very hot, humid or
corrosive environments.
● Take care not to touch the SmartMedia’s contact area
or allow the area to become soiled. Use a dry lint-free
cloth to wipe away any soiling that does occur.
● To
avoid damage caused by static electricity, always
use the special static-free case provided during
transportation or storage, or keep the SmartMedia in
a storage case if available.
● Do not carry SmartMedia in locations such as a
trouser pocket. This could subject the SmartMedia to
excessive force when you sit down, thereby
damaging the SmartMedia.
● The SmartMedia may feel warm when it is removed
from the camera after extended periods of picture
taking or image viewing. This is normal and does not
indicate a fault.
● Inserting a SmartMedia that is charged with static
electricity into your camera may result in a camera
malfunction. If this occurs, switch the camera off and
then on again.
● Affix the label onto the designated area of the card.
Do not use third-party labels as this can lead to
problems when the card is inserted or removed.
● When you attach the label, take care that it does not
cover any of the write-protect area.
■ Notes on Using SmartMedia with a PC
● If
you intend to take photos using a SmartMedia that
has been used on a PC, format the SmartMedia on
your camera.
● When you format a SmartMedia in the camera and
then shoot and record images, a directory (folder) is
automatically created. Image data is then recorded in
this directory.
● Do not change or delete the directory (folder) names
or file names on the SmartMedia from your PC as this
will make it impossible to use the SmartMedia in your
camera.
● Always use the camera to erase image data on a
SmartMedia.
● To edit image data, copy the image data to the
computer’s hard disk and then edit the copied data.
■ Specifications
Type
Image memory card for digital
cameras (SmartMedia)
Operating voltage
3.3V
Operating conditions Temperature:
0°C to +40°C=(+32°F to +104°F)
Humidity:
80% or less (condensation free)
Dimensions
37 ✕ 45 ✕ 0.76mm
(1.45 ✕ 1.77 ✕ 0.03in.) (W ✕ H ✕ D)
111
Warning Displays
The table below lists the warnings that are displayed on the LCD monitor.
Explanation
LCD Monitor
LCD Panel
Warning Displayed
112
LCD Monitor
The camera battery is low on
charge.
Replace or recharge the battery.
No SmartMedia is loaded, or it is
loaded incorrectly.
Load a SmartMedia or reload the SmartMedia
the correct way round.
The SmartMedia is not formatted.
Format the SmartMedia.
• The SmartMedia terminals are
soild.
• The SmartMedia is damaged.
• The SmartMedia format is
incorrect.
Explanation
Remedy
F I L E
L I M I T
Erase some images or use a SmartMedia that
has ample free space.
The SmartMedia is write-protected.
Use a SmartMedia that is not write-protected.
Warning Displayed
Remedy
An attempt was made to playback a
frame not recorded on this camera.
Images cannot be played back.
The frame number has reached
999-9999.
Switch the Frame NO. Memory function off
and use a formatted SmartMedia to take the
picture.
—
There is a strong likelihood of
camera shake because the
shutter speed is slow.
Set the flash to Forced Flash mode or use a
tripod.
—
A protected frame was erased.
Remove the protection.
X AF
—
The AF (auto focus) cannot work
effectively.
• If the shot is too dark, move at least 1.5
meters away from the subject and try again.
• Use AF lock to take the picture.
X AE
—
Outside the AE continuous range.
The shot can be taken, but the exposure will
not be correct.
Wipe the contact area on the SmartMedia with
a soft dry cloth. It may be necessary to format
the SmartMedia. If the error message is still
displayed, replace the SmartMedia.
The SmartMedia is fully recorded.
LCD Panel
113
Troubleshooting
Warning Displays
Problem
Explanation
Warning Displayed
Remedy
—
The image you tried to erase has
a DPOF print setting.
When you erase the image, the DPOF
settings for that image are deleted at the same
time.
—
The DPOF file contains an error.
Alternatively, the DPOF file was
set up on a different device.
Press the MENU/EXE button to create a new
DPOF file and specify all the DPOF settings
again.
—
Prints were specified for more
than 999 frames in the DPOF
frame settings.
The maximum number of frames for which
prints can be specified on the same
SmartMedia is 999.
• The lens cover is not open.
• Camera malfunction or fault.
Switch the camera on again, ensuring that you
are not touching the lens cover at the
time.Switch the camera off and then on again
a few times.
LCD Monitor
LCD Panel
DPOF SPECIFIED.
ERASE OK?
If you think the camera is faulty, check the following once more
Cause
• The terminals are soiled.
114
Remedy
• Load a new fully charged battery.
• The battery is exhausted.
• The AC power adapter plug has come out of • Plug the adapter back in.
the power outlet.
• Load a new fully charged battery.
Power cuts out during • The battery is exhausted.
operation.
• You are using the camera in extremely cold • Put the battery in your pocket or another
Battery runs out quickly.
conditions.
warm place to heat it and then load it into
the camera just before you take a picture.
No power
• The battery is flat.
No photograph is taken • No SmartMedia is loaded.
when the shutter button is • The SmartMedia is fully recorded.
pressed.
• The SmartMedia is write-protected.
• The SmartMedia is not formatted.
• The SmartMedia contact area is soiled.
• Wipe the battery terminals with a clean, dry
cloth.
• Load a new fully charged battery.
• Load a SmartMedia.
• Load a new SmartMedia or erase a frame.
• Remove the write-protection.
• Format the SmartMedia.
• Wipe the SmartMedia contact area with a
clean dry cloth.
• Load a new SmartMedia.
• The SmartMedia is damaged.
• The Auto Power Off function has switched • Switch the camera on.
the camera off.
• The battery is exhausted.
• Load a new fully charged battery.
115
Troubleshooting
Problem
Cause
Remedy
• Set the Mode switch and Photography
mode dial to the correct setting.
• Set the flash to Auto, Red-Eye Reduction or
Forced Flash mode(Pop the flash unit up).
• Wait until charging is completed before
pressing the shutter button.
• Load a new SmartMedia, erase a frame, or
remove the write-protection.
• The camera is set to Suppressed Flash • Set the flash to Auto, Red-Eye Reduction or
Forced Flash mode.
mode.
• Cancel Macro Photography.
• The camera is set to Macro Photography.
• The battery is exhausted.
• Load a new battery.
• Move closer to the subject.
The playback image is too • The subject is too far away.
• Hold the camera correctly.
dark even though I used • Your finger covering the flash.
the flash.
The image is blurred.
• The lens is dirty
• Clean the lens.
• The lens is zoomed to telephoto in Macro • Cancel Macro mode.
mode.
I cannot format the • The SmartMedia is write-protected.
• Remove the write-protection.
SmartMedia.
(Peel off the write-protect sticker.)
I cannot erase all the • The frame is protected.
• Remove the frame protection.
frames.
I can’t use the flash to take • The Mode switch and Photography mode
pictures.
dial has been moved to another setting.
• The flash is set to Suppressed Flash
mode(The flash is closed).
• You pressed the shutter button while the
flash was charging.
• No compatible SmartMedia is loaded.
The flash will not charge.
116
Problem
Cause
Nothing happens when I • Camera malfunction.
use the camera switches
and dial.
• The Mode switch and Photography mode
dial has been moved to another setting.
• The battery exhausted.
No image appears when I • The Mode switch and Photography mode
press the, “DISP” button.
dial has been moved to another setting.
There is no sound.
• sounThe camera volume is set too low.
• The microphone was covered during
recording.
• The A/V cable is connected.
There is no picture or • The A/V cable is connected during movie
playback.
sound on the TV.
• The camera and TV are connected
incorrectly.
• The TV input is set to “TV”.
• The volume on the TV is set too low.
Remedy
• Use the “POWER” switch to switch the
camera on again.
• Remove the battery, re-insert them and try
again.
• Load a new battery.
• Move the Mode dial to the correct setting.
• Adjust the volume.
• Take care not to cover the microphone
when recording.
• Disconnect the A/V cable.
• Connect the A/V cable correctly.
• Connect the TV and camera correctly.
• Set the TV input to “Video”.
• Adjust the volume.
117
Specifications
System
● Model:Digital camera FinePix4700 ZOOM
● CCD Sensor
1/1.7-inch Super CCD(with primary color filter), 2.4million
pixels in an interwoven pattern
● Image file Size:2,400 ✕ 1,800 pixels / 1,280 ✕ 960 pixels /
640 ✕ 480 pixels
● File format
Still image:DCF-compliant (Exif ver.2.1 JPEG-compliant),
DPOF-compatible
Movie:DCF-compliant (AVI format , Motion JPEG)
● Storage media:SmartMedia (3.3V)
● Viewfinder:Real image optical
● Lens:Super EBC Fujinon optical 3✕ zoom lens
F2.8/F7.0 (wide-angle) to F4.5/F10.8 (telephoto)
● Focus distance:f = 8.3~24.9mm
● LCD monitor
(equivalent to 36-108mm on a 35mm camera)
● Exposure control:64 zones TTL metering, Program AE
(exposure compensation available in Manual mode)
● Sensitivity:Equivalent to ISO 200/400/800
● White balance
Auto-selected (7 modes selectable in Manual mode)
● Focal range
Normal : Approx. 80cm /2.6 ft. to infinity
Macro : Approx. 20cm /0.7 ft. to 80cm/ 2.6 ft.
● Electronic shutter
Variable-speed, 3 to 1/2,000 sec. (using AE)
● Flash:Auto flash using flash control sensor
Effective range : Wide Approx. 0.2m~4m (0.7 ft.~13.1 ft.)
Tele Approx. 0.2m~3m (0.7 ft.~9.8 ft.)
Flash modes : Auto, Red-Eye Reduction,
Forced Flash, Suppressed Flash,
Night Scenes (Slow Synchro)
2-inch, low-temperature polysilicon TFT 130,000 pixels
● Video output
NTSC (US/ Canada model) / PAL (Europe model)
● Self-Timer:10 sec. timer clock
● Number of frames recorded
640✕480
FINE
NORMAL
BASIC
FINE
NORMAL
BASIC
Image Data Size
APPROX.
1700KB
APPROX.
803KB
APPROX.
328KB
APPROX.
612KB
APPROX.
312KB
APPROX.
162KB
2
4
9
18
36
4
9
19
38
77
11
23
47
94
189
6
12
25
50
101
12
24
49
99
198
23
47
90
180
362
MG-8S(8MB)
MG-16S(16MB)
MG-32S(32MB)
118
1280✕960
Quality Mode
MG-4S(4MB)
MG-64S(64MB)
Stereo mini- jack (1), Audio: 316mVrms, output impedance
2.2 KΩ or less
● Digital
USB (1) for image data output with a personal computer
● DC Input
Socket for specified AC power adapter
Power Supply and Others
● Power supply
2400✕1800
File Size
Input/Output Terminals
● A / V Output
This indicates the number of available frames shot
consecutively at room temperature with a flash use rate of
50%. Note that these figures may vary depending on the
ambient temperature and the amount of charge in the battery.
● Conditions for use
Temperature : 0°C to +40°C (+32°F to +104°F) ; 80%
humidity or less (no condensation)
● Camera dimensions (W/H/D)
78 ✕ 97.5 ✕ 32.9mm / 3.1 ✕ 3.8 ✕ 1.3 in. (not including
accessories and attachments)
● Camera mass (weight)
Approx. 255g / 9.0oz. (not including accessories, batteries or
SmartMedia)
● Weight for photography
Approx. 310g / 10.9oz. (including batteries and SmartMedia)
● Accessories:See P.7
● Optional Accessories:See P.101-104
FINE
NORMAL
Movie
BASIC
APPROX. APPROX. APPROX.
162KB
87KB
50KB
23
47
90
180
362
44
89
165
331
663
70
141
248
498
996
---------------------
22sec.
45sec.
Use one of the following:
• 2AA-size Ni-MH (nickel metal hydride) batteries (included)
• 2AA-size long-life (Minimum 1,000mAn) Ni-Cd (nickelcadmium) batteries (sold separately)
• AC-3V AC Power Adapter (sold separately)
● No. of available shots using battery (battery life)
LCD monitor
on
LCD monitor
off
Ni-MH battery HR-3UF
Approx. 80
Approx. 230
Ni-Cd battery KR-3UF
Approx. 50
Approx. 140
Battery Type
90sec.
182sec.
364sec.
✽ These specifications are subject to change without notice.
✽ The LCD monitor on your digital camera is manufactured
using advanced high-precision technology. Even so, small
bright points and anomalous colors (particularly around
text) may appear on the monitor. These are normal display
characteristics and do not indicate a fault with the monitor.
This phenomenon will not appear on the recorded image.
119
Safety Notes
● To ensure that you use your FinePix4700 ZOOM
camera correctly, read these Safety Notes and your
Owner’s Manual carefully beforehand.
● After reading these Safety Notes, store them in a safe
place.
About the Icons
The icons shown below are used in this document to
indicate the severity of the injury or damage that can result
if the information indicated by the icon is ignored and the
product is used incorrectly as a result.
WARNING
This icon indicates that death or
serious injury can result if the
information is ignored.
CAUTION
This icon indicates that personal
injury or material damage can
result if the information is ignored.
The icons shown below are used to indicate the nature of
the information which is to be observed.
Triangular icons notify the user of information
requiring attention (“Important”).
Circular icons with a diagonal bar notify the user
that the action indicated is prohibited
(“Prohibited”).
120
Filled circles with an exclamation mark notify the
user of an action that must be performed
(“Required”).
WARNING
When a fault arises, switch the
camera off and then remove the
batteries and disconnect the AC
power adapter.
Continued use of the camera when it is
emitting smoke, is emitting any unusual
odor, or is in any other abnormal state
can cause a fire or electric shock.
● Contact your Fuji dealer.
Do not allow water or foreign objects
to enter the camera.
If water or a foreign object has entered
the camera, switch the camera off and
then remove the batteries and
disconnect the AC power adapter.
Continued use of the camera can cause
a fire or electric shock.
● Contact your Fuji dealer.
Do not place the camera on an
unstable surface.
This can cause the camera to fall or tip
over and cause injury.
WARNING
Unplug from
power socket.
Never attempt to modify or
disassemble the camera. (Never open
the casing.)
Do not use the camera when it has been
dropped or the casing is damaged.
This can cause a fire or electric shock.
● Contact your Fuji dealer.
WARNING
Do not
disassemble.
Do not use the camera in the
bathroom or shower.
This can cause a fire or electric shock.
Do not use in the
bathroom or shower.
Never attempt to take pictures whilst
in motion.
Do not use the camera while you are
walking or operating a moving car or
other vehicle.
This can result in you falling down or
being involved in a traffic accident.
Do not touch any metal parts of the
camera during a thunderstorm.
This can cause an electric shock due to
induced current from the lightning
discharge.
Do not use the batteries except as
specified.
Load the batteries with the poles
positioned as indicated by the and
marks.
Do not heat, modify or attempt to
disassemble the batteries.
Do not drop or subject the batteries
to impacts.
Do not attempt to recharge lithium or
alkaline batteries.
Do not store the batteries with
metallic products.
Any of these actions can cause the
batteries to burst or leak and cause fire
or injury as a result.
Use only the batteries or AC power
adapter specified for use with this
camera.
The use of other power sources can
cause a fire.
121
EC Declaration of Conformity
Safety Notes
CAUTION
122
CAUTION
Do not use this camera in locations
severely affected by oil fumes, steam,
humidity or dust.
This can cause a fire or electric shock.
Do not cover or wrap the camera or
the AC power adapter in a cloth or
quilt.
This can cause heat to build up and
distort the casing or cause a fire.
Do not leave this camera in places
subject
to
extremely
high
temperatures.
Do not leave the camera in locations
such as a sealed vehicle or in direct
sunlight.
This can cause a fire.
Remove the batteries and disconnect
the AC power adapter when you are
cleaning the camera or if you intend
to leave the camera unused for a long
period.
Failure to do so can cause a fire or
electric shock.
Do not place heavy objects on the
camera.
This can cause the heavy object to tip
over or fall and cause injury.
Do not use the flash close to
anyone’s eyes.
This can cause temporary damage to
the person’s eyesight.
Do not move the camera while the AC
power adapter is still connected.
This can damage the power cord or
cables and cause a fire or electric shock.
Request regular internal testing and
cleaning for your camera.
Build-ups of dust in your camera can
cause a fire or electric shock.
● Contact your Fuji dealer to request
internal cleaning every 2 years.
We
Name :
Address :
declare that the product
Product Name :
Manufacture’s Name :
Manufacture’s Address :
Fuji Photo Film (Europe) G.m.b.H.
Heesenstrasse 31
40549 Dusseldorf, Germany
DIGITAL CAMERA FUJIFILM FinePix4700 ZOOM
Fuji Photo Film Co., Ltd.
26 - 30, Nishiazabu 2 - chome, Minato - ku,
Tokyo 106-8620, Japan
is in conformity with the following Standards
Safety : EN60065
EMC : EN55022 :
1994 + amendement 1 Classe B
EN50082-1 : 1992
EN61000-3-2 : 1995
following the provision of the EMC Directive (89/336/EEC, 92/31/EEC and
93/68/EEC) and Low Voltage Directive (73/23/EEC).
Dusseldorf,Germany
March 1,2000
Place
Date
Signature/Managing Director
Bij dit produkt zijn batterijen geleverd. Wanneer deze leeg zijn, moet u ze niet
weggooien maar inleveren als KCA
123
26-30, Nishiazabu 2-chome, Minato-ku, Tokyo 106-8620, Japan
Printed in Japan
Printed on recycled paper.
FGS-002102-FG