ADJ InnoColor Beam12 User manual

Inno Color Beam 12 Introduction
Unpacking: Thank you for purchasing the Inno Color Beam 12 by
InnoColor
Beam12
American DJ®. Every Inno Color Beam 12 has been thoroughly tested
and has been shipped in perfect operating condition. Carefully check
the shipping carton for damage that may have occurred during shipping. If the carton appears to be damaged, carefully inspect your fixture for any damage and be sure all accessories necessary to operate
the unit has arrived intact. In the case damage has been found or parts
are missing, please contact our toll free customer support number for
further instructions. Do not return this unit to your dealer without first
contacting customer support.
Introduction: The Inno Color Beam 12 is part of American DJ’s con-
tinuing pursuit for creating high quality affordable intelligent fixtures.
The Inno Color Beam 12 is a compact, high performance, DMX intelligent, moving head, LED fixture. This fixture is a great piece for retail
stores, displays, mood, architectural, interior and exterior decoration,
and clubs. This unit can be used as a stand alone, or in a Master/Slave
configuration. The unit can also be controlled via DMX controller.
Customer Support: American DJ® provides a toll free customer sup-
port line, to provide set up help and to answer any question should you
encounter problems during your set up or initial operation. You may
also visit us on the web at www.americandj.com for any comments or
suggestions. Service Hours are Monday through Friday 8:00 a.m. to
4:30 p.m. Pacific Standard Time.
Voice:
(800) 322-6337
Fax: (323) 582-2941
E-mail: support@americandj.com
To purchase parts online visit http://parts.americandj.com
Warning! To prevent or reduce the risk of electrical shock or fire, do
not expose this unit to rain or moisture.
Caution! There are no user serviceable parts inside this unit. Do not
User Instructions
attempt any repairs yourself, doing so will void your manufactures warranty. In the unlikely event your unit may require service please contact
American DJ®.
PLEASE recycle the shipping carton when ever possible.
8/12
©American
DJ Supply® - www.americandj.com - Inno Color Beam 12 User Manual Page 2
Inno Color Beam 12
General Instructions
To optimize the performance of this product, please read these operating instructions carefully to familiarize yourself with the basic operations
of this unit. These instructions contain important safety information
regarding the use and maintenance of this unit. Please keep this manual
with the unit, for future reference.
Inno Color Beam 12 Features
• RGB Color Mixing
• 12 x 3W High Quatlity CREE LEDs
• Color Strobe Effect
• 32 Built-In Color Macros
• Pan: 540-Degree; Tilt: 270-Degree
• Pan/Tilt Inversion
• Electronic Dimming 0-100%
• Fan Cooled
• Built in Microphone
• DMX-512 protocol
• Two DMX Modes: 9 Channel Mode & 16 Channel Mode
• 3 Operating Modes - Sound Active, Show Mode, or DMX Control
• UC3 Remote Control Compatiable (Not Included)
Inno Color Beam 12
Warranty Registration
The Inno Color Beam 12 carries a 3 year (1095 days) limited warranty.
Please fill out the enclosed warranty card to validate your purchase
and warranty. You may also register your product online at www.
americandj.com. All returned service items whether under warranty or
not, must be freight pre-paid and accompany a return authorization
(R.A.) number. If the unit is under warranty you must provide a copy
of your proof of purchase invoice. Please contact American DJ® customer support for a R.A. number.
©American
DJ Supply® - www.americandj.com - Inno Color Beam 12 User Manual Page 3
Inno Color Beam 12
Safety Precautions
•To reduce the risk of electrical shock or fire, do not expose this unit rain or moisture
•Do not spill water or other liquids into or on to your unit.
•Be sure that the local power outlet match that of the required volt-
age for your unit.
•Do not attempt to operate this unit if the power cord hasbeen
frayed or broken. Do not attempt to remove or break off the ground
prong from the electrical cord. This prong is used to reduce the risk of electrical shock and fire in case of an internal short.
•Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user serviceable parts inside.
•Never operate this unit when it’s cover is removed.
•Never plug this unit in to a dimmer pack
•Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6” (15cm) between this device and a wall.
•Do not attempt to operate this unit, if it becomes damaged.
•This unit is intended for indoor use only, use of this product out`
doors voids all warranties.
•During long periods of non-use, disconnect the unit’s main power.
•Always mount this unit in safe and stable matter.
•Power-supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them, paying particular attention to the point they exit from the unit.
• Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See page 18 for cleaning details.
•Heat -The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat.
•The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a marked change in performance.
©American
DJ Supply® - www.americandj.com - Inno Color Beam 12 User Manual Page 4
POWER
Inno Color Beam 12
Set Up
Inno Color Beam 12
Notice: Be sure to follow figures two and three when making your own
cables. Do not use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
DMX-512: DMX is short for Digital Multiplex. This is a universal pro-
COMMON
tocol used as a form of communication between intelligent fixtures
and controllers. A DMX controller sends DMX data instructions from
the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have a DATA
“OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models of
different manufactures to be linked together and operate from a single
controller, as long as all fixtures and the controller are DMX compliant. To ensure proper DMX data transmission, when using several
DMX fixtures try to use the shortest cable path possible.
The order
DMX512
in which fixtures are connected in a DMX line DMX+,DMX-,COMMON
does not influence the
DMX addressing. For example; a fixture assigned a DMX address of 1
may be placed anywhere in a DMX line, at the beginning, at the end,
or anywhere in the middle. When a fixture is assigned a DMX address
of 1, the DMX controller knows to send DATA assigned to address 1
to that unit, no matter where it is located in the DMX chain. COMMON
REMOTE
CONTROL
INPUT
INPUT
OUTPUT
REMOTE
CONTROL
2
DMX +
3
The Inno Color Beam 12 can be controlled via DMX-512 protocol. The
Inno Color Beam 12 can be either a 9 Channel or 16 Channel DMX unit.
The DMX address is set on the rear panel of the Inno Color Beam 12.
Your unit and your DMX controller require a approved DMX-512 110
Ohm Data cable for data input and data output (Figure 1). We recommend Accu-Cable DMX cables. If you are making
your own cables, be sure to use standard 110120 Ohm shielded cable (This cable may be
purchased at almost all professional sound and
lighting stores). Your cables should be made with
a male and female XLR connector on either end
of the cable. Also remember that DMX cable must
be daisy chained and cannot be split.
1 Ground
OUTPUT
3
DMX -
1
2
SOUND
XLR Female Socket
2 Cold
2 Cold
1 Ground
DMX512 IN
3-PIN XLR
REMOTE
CONTROL
INPUT
INPUT
3
Figure 2
OUTPUT
1
2
Termination redu
avoids signal tra
and interference.
to connect a DMX
120 Ohm 1/4 W)
and PIN 3 (DMX
XLR Pin Configuration
Pin 1 = Ground
Pin 2 = Data Compliment (negative)
3 Hot
Figure 3
3 Hot
Pin 3 = Data True (positive)
POWER
POWER
Special Note: Line Termination. When longer runs of cable are
3
1
2
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
Termination reduces signal errors and
DMX512 IN
3-PIN XLR
3
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
1
2
Figure 4
5-Pin XLR DMX Connectors. Some manufactures use 5-pin XLR
connectors for DATA transmission in place of 3-pin. 5-pin XLR fixtures
may be implemented in a 3-pin XLR DMX line. When inserting standard
5-pin XLR connectors in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
3-Pin XLR to 5-Pin XLR Conversion
Conductor
3-Pin XLR Female (Out)
5-Pin XLR Male (In)
Ground/Shield
Pin 1
Pin 1
Data Compliment (- signal)
Pin 2
Pin 2
Data True (+ signal)
Pin 3
Figure 1
©American DJ® - www.americandj.com - Inno Color Beam 12 User Manual Page 5
INPUT
2
DMX +
3
XLRINPUT
Male Socket
POWER
1
1
DMX512 OUT
3-PIN XLR
SOUND
OUT
Data Cable (DMX Cable) Requirements DMX512
(For
DMX Operation):
3-PIN XLR
DMX -
Set Up
DMX512
DMX+,DMX-,COMMON
Power Supply: The American DJ® Inno Color Beam 12 contains a
automatic voltage switch, which will auto sense the voltage when it is
plugged into a power source. With this switch there is no need to worry
about the correct power voltage, this unit can be plugged in anywhere.
SOUND
POWER
©American
Pin 3
Not Used
Do Not Use
Not Used
Do Not Use
DJ Supply® - www.americandj.com - Inno Color Beam 12 User Manual Page 6
Inno Color Beam 12
System Menu
Inno Color Beam 12
System Menu
ADDR - DMX Address Setting via control board -
1. Press the MENU button until “ADDR” is displayed, press ENTER.
2. “X” will now be displayed, “X” represents the displayed address.
Press the UP or DOWN buttons to find your desired address.
3. Press ENTER to confirm, then connect your DMX controller.
NOTE: If after you connect your DMX controller the unit does not
fall into DMX mode, press and hold the MENU button for at least
3 seconds.
CHND - This will let select your desired DMX channel
mode.
1. Press the either the MENU button until “CHND” is displayed,
press ENTER. Either “9CH” or “16CH” will be displayed
2. Press the UP or DOWN buttons to find your desired DMX
channel mode and press ENTER to confim and exit.
SLND - This will let you set unit as a master or slave in a
master/slave configuration.
1. Press the MENU button until “SLND” is displayed, press
ENTER. Either “SL 1” or “SL 2” will be displayed.
2. Press the UP or DOWN buttons until your desired setting is
displayed, press ENTER to confim.
NOTE: In a Master/Slave configuration you can set one fixture
to Slave 1 (SL 1) and then set the next fixture to Slave 2 (SL 2),
in doing this the fixtures will now have contrast movement to
each other.
SHND: SH 0 - SH 4 - Show modes 0 - 4. Show mode can
run with or without sound active mode on.
1. Press the MENU button until “SHND” is displayed, press ENTER.
©American
DJ Supply® - www.americandj.com - Inno Color Beam 12 User Manual Page 7
©American
DJ Supply® - www.americandj.com - Inno Color Beam 12 User Manual Page 8
Inno Color Beam 12
System Menu
Inno Color Beam 12
System Menu
2. “SH X” will now be displayed, “X” representing a number
between 0-4. Shows 1-4 are preset shows, while “SH 0” is random
show. Press the UP or DOWN buttons to find your desired show.
unit will automatically go into the last DMX set up.
3. Once you have found your desired show press ENTER, and
then press and hold the MENU button for at least 3 seconds to
confirm.
LED - With this function the LED display will turn off after 2
SOUN - In this submenu you can activate sound active mode.
3. Press ENTER to confirm your desired set up.
minutes.
1. Press the MENU button until “LED” is displayed, press ENTER.
2. Either “ON” or “OFF” will now be displayed. Press the UP or
DOWN buttons to select one or the other.
2. Either “ON” or “OFF” will now be displayed. Press the UP or
DOWN buttons to select “ON” to keep the LED display on at all
times, or “OFF” to allow the LED display to turn off after 2 minutes. Press any button to turn the LED display on again.
3. When you have made your selection, press the ENTER, and
then press and hold the MENU button for at least 3 seconds to
confirm.
PAN - Pan Inversion
1. Press the MENU button until “SOUN” is displayed, press ENTER.
DNST - This mode can be used as a precaution mode, that
in case the DMX signal is lost, the operating mode chosen in
the setup is the running mode the fixture will go into when
the DMX signal is lost. You can also set this as the operating mode you would like the unit to return to when power is
applied.
1. Press the MENU button until “DNST” is displayed, press ENTER.
2. Either “MASL”, “BLND”, or “LAST” will be displayed. Choose an
operating mode you would like the unit to start up in when power
is applied or the DMX signal is lost.
3. Press ENTER to confirm your selection.
1. Press the MENU button until “PAN” is displayed, press
ENTER. Either “YES” or “NO” will be displayed.
2. To activate the Pan inversion press the UP or DOWN buttons
until “YES” is displayed, press ENTER to confim. To deactivate
Pan inversion, select “NO” and press Enter.
TILT - Tilt Inversion
1. Press the MENU button until “TILT” is displayed, press ENTER.
Either “YES” or “NO” will be displayed.
• MASL (Master Slave) - If the DMX signal is lost or power is
applied, the unit will automatically go into Master Slave mode.
2. To activate the Tilt inversion press the UP or DOWN buttons
until “YES” is displayed, press ENTER to confim. To deactivate
Tilt inversion, select “NO” and press Enter.
• BLND (Blackout) - If the DMX signal is lost or power is applied,
the unit will automatically go into stand by mode.
DISP - This will “flip” the LED display
• LAST (Last State) - If the DMX signal is lost the fixture will stay in
the last DMX set up. If power is applied and this mode is set, the
1. Press the MENU button until “DISP” is displayed, press
ENTER.
©American
DJ Supply® - www.americandj.com - Inno Color Beam 12 User Manual Page 9
©American
DJ Supply® - www.americandj.com - Inno Color Beam 12 User Manual Page 10
Inno Color Beam 12
System Menu
Inno Color Beam 12
System Menu
2. When “DISP” is displayed the LED display will remain normal,
when “DSIP” is displayed, the LED display will be “flipped”.
Press the ENTER button to set your desired .
TEDT - With this function you can check the LED tempera-
BALA - With this function you are able to adjust the RGB
colors to create your desired shade of white.
2. The LED temperature will now be displayed. Press MENU to
exit.
1. Press the MENU button until “BALA” is displayed, press
ENTER.
CPUT - With this function you can check the temperature of
2. Use the UP and DOWN buttons to scroll through the RGB
colors. Once you have found your desired color you would like
to adjust press ENTER.
3. After you have pressed ENTER, use the UP and DOWN buttons to adjust the intensity of the color. Continue to adjust the
RGB colors until you have reached your desired shade of white.
MANU - In this submenu you are able to test the different
functions; pan, tilt, LEDs, dimmer, and strobe.
1. Press the MENU button until “MANU” is displayed, press
ENTER.
2. Use the UP and DOWN buttons to scroll through the various
functions able for testing. Once you have found your desired
function you would like to test press ENTER.
3. After you have pressed ENTER, use the UP and DOWN buttons to adjust the values and test the function. To exit press the
MENU button.
TEST - This function will run a self test program. The test
program will test pan/tilt movement and colors.
1. Tap the MENU button until “TEST” is displayed, press ENTER.
2. The fixture will now run a self test.
©American
DJ Supply® - www.americandj.com - Inno Color Beam 12 User Manual Page 11
ture.
1. Tap the MENU button until “TEDT” is displayed, press ENTER.
the fixture.
1. Tap the MENU button until “CPUT” is displayed, press ENTER.
2. The temperature of the fixture will now be displayed. Press
MENU to exit.
FHRS - With this function you can display the running time
of the unit.
1. Press the MENU button until “FHRS” is displayed, press
ENTER.
2. The running time of the fixture will now be displayed. Press
MENU to exit.
VER - This will display the software version
1. Press the MENU button until “VER” is displayed. Press the
ENTER button and the software vesion will be displayed.
2. Press the MENU button to leave this function.
RSET - Use this function to reset the unit.
1. Tap the MENU button until “RSET” is displayed, press ENTER.
2. The fixture will now reset,
©American
DJ Supply® - www.americandj.com - Inno Color Beam 12 User Manual Page 12
Inno Color Beam 12
Universal DMX Control
Universal DMX Control: This function allows you to use a Elation®
universal DMX-512 controller to control the chases and patterns,
dimmer and strobe. A DMX controller allows you to create unique
programs tailored to your individual needs. The Inno Color Beam 12
has 2 DMX channel modes; a 9 Channel Mode & 16 Channel Mode.
To select your channel mode see page 8.
1. This function will allow you to control each individual fixture’s
traits with a standard DMX 512 controller such as the
Elation® Show Designer™ or the Elation® DMX Operator.™ See pages 14-16 for the DMX modes & traits.
2. To run your fixture in DMX mode, select your desired channel mode and then set your desired DMX address following the directions on page 8, and the set-up specifications that come with your DMX controller.
3. Plug in the fixture via the XLR connections to any standard DMX controller.
4. For longer cable runs (more than a 100 feet) use a terminator on the last fixture.
Inno Color Beam 12
Master-Slave Configuration
Master-Slave Configuration: This function will allow you to link up
to 16 units together and operate without a controller. The units will be
sound activated. In Master-Slave operation one unit will act as the controlling unit and the others will react to the controlling units programs.
Any unit can act as a Master or as a Slave.
1. Using approved DMX data cables, daisy chain your units togeth- er via the XLR connector on the rear of the units. Remember the Male XLR connector is the input and the Female XLR connector
is the output. The first unit in the chain (master) will use the female XLR connector only - The last unit in the chain will use the male XLR connector only. For longer cable runs we suggest a termina-
tor at the last fixture.
2. Set the Master unit to your desired operating mode.
3. On the slave units tap the MENU button until “Slave Mode” is dis played, and Press ENTER. Choose either “Slave 1” or “Slave 2” and press ENTER. See page 9 for more info.
4. The slave units will now follow the Master unit.
©American
DJ Supply® - www.americandj.com - Inno Color Beam 12 User Manual Page 13
Inno Color Beam 12
Channel
1
2
3
4
5
6
7
8
9
Value
0 - 255
0 - 255
0-7
8 - 15
16 - 131
132 - 139
140 - 181
182 - 189
190 - 231
232 - 239
240 - 247
248 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 69
70 - 79
80 - 89
90 - 199
200 - 209
210 - 239
240 - 255
©American
9 Channel Mode
Function
PAN 0° - 540°
TILT 0° - 270°
SHUTTER/STROBING
BLACKOUT
OPEN
STROBING SLOW - FAST
OPEN
SLOW OPEN - FAST CLOSE
OPEN
SLOW CLOSE - FAST OPEN
OPEN
RANDOM STROBE
OPEN
RED
0% - 100%
GREEN
0% - 100%
BLUE
0% - 100%
WHITE
0% - 100%
MASTER DIMMER
0% - 100%
SPECIAL FUNCTIONS
NO FUNCTION
ENABLE BLACKOUT WHILE PAN OR TILT MOVEMENT
DISABLE BLACKOUT WHILE PAN OR TILT MOVEMENT
NO FUNCTION
RESET
NO FUNCTION
SOUND ACTIVE
DJ Supply® - www.americandj.com - Inno Color Beam 12 User Manual Page 14
Inno Color Beam 12
Channel
1
2
3
4
5
6
7
8
Value
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 15
16 - 35
36 - 55
56 - 75
76 - 95
96 - 115
116 - 135
136 - 155
156 - 175
176 - 195
196 - 215
216 - 235
236 - 255
0 - 255
0 - 69
70 - 79
80 - 89
9
©American
90 - 199
200 - 209
210 - 239
240 - 255
0 - 255
16 Channel Mode
Function
PAN 0° - 540°
PAN FINE
TILT 0° - 270°
TILT FINE
PAN/TILT SPEED
FAST - SLOW
PAN/TILT MACROS
STOP
MACRO 1
MACRO 2
MACRO 3
MACRO 4
MACRO 5
MACRO 6
MACRO 7
MACRO 8
MACRO 9
MACRO 10
MACRO 11
MACRO 12
PAN/TILT MACRO SPEED
FAST - SLOW
SPECIAL FUNCTIONS
NO FUNCTION
ENABLE BLACKOUT WHILE PAN OR TILT MOVEMENT
DISABLE BLACKOUT WHILE PAN OR TILT MOVEMENT
NO FUNCTION
RESET
NO FUNCTION
SOUND ACTIVE
MASTER DIMMER
0% - 100%
DJ Supply® - www.americandj.com - Inno Color Beam 12 User Manual Page 15
Inno Color Beam 12
Channel
10
11
12
13
14
15
16
©American
Value
0-7
8 - 15
16 - 131
132 - 139
140 - 181
182 - 189
190 - 231
232 - 239
240 - 247
248 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0-7
8 - 127
128 - 191
192 - 255
0 - 255
16 Channel Mode
Function
SHUTTER/STROBING
BLACKOUT
OPEN
STROBING SLOW - FAST
OPEN
SLOW OPEN - FAST CLOSE
OPEN
SLOW CLOSE - FAST OPEN
OPEN
RANDOM STROBE
OPEN
RED
0% - 100%
GREEN
0% - 100%
BLUE
0% - 100%
WHITE
0% - 100%
COLOR FUNCTIONS
NORMAL
32 COLOR MACROS
COLOR CHANGING
COLOR FADING
COLOR CHANGE/FADE SPEED
SLOW - FAST
DJ Supply® - www.americandj.com - Inno Color Beam 12 User Manual Page 16
Inno Color Beam 12
Photometric Chart
Inno Color Beam 12
Fuse Replacement
Locate and remove the unit’s power cord. Once the cord has been
removed located the fuse holder located inside the power socket.
Insert a flat-head screw driver into the power socket and gently pry out
the fuse holder. Remove the bad fuse and replace with a new one. The
fuse holder has a built-in socket for a spare fuse be sure not to confuse
the spare fuse with active fuse.
Inno Color Beam 12
Cleaning
Due to fog residue, smoke, and dust cleaning the internal and external optical lenses must be carried out periodically to optimize light
output.
Inno Color Beam 12
UC3 Control
1. Use a soft cloth to wipe down the outside casing.
Cleaning frequency depends on the environment in which the fixture
operates (i.e. smoke, fog residue, dust, dew).
Inno Color Beam 12
Troubleshooting
Listed below are a few common problems the user may encounter,
with solutions.
Unit not responding to DMX:
1.
Check that the DMX cables are connected properly and are wired correctly (pin 3 is “hot”; on some other DMX devices pin 2 may be ‘hot’). Also, check that all cables are connected to the right connectors; it does matter which way the inputs and outputs are connected.
Unit does not respond to sound:
1. Quiet or high pitched sounds will not activate the unit.
If problems are not resolved; Contact American DJ® for service.
1-800-322-6337
©American
DJ Supply® - www.americandj.com - Inno Color Beam 12 User Manual Page 17
©American
DJ Supply® - www.americandj.com - Inno Color Beam 12 User Manual Page 18
Inno Color Beam 12
Warranty
MANUFACTURER’S LIMITED WARRANTY
A. American DJ, Inc. hereby warrants, to the original purchaser, American DJ and American
Audio products to be free of manufacturing defects in material and workmanship for a prescribed
period from the date of purchase (see specific warranty period on reverse). This warranty shall be
valid only if the product is purchased within the United States of America, including possessions and
territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.
B.
For warranty service you must obtain a Return Authorization number (RA#) before sending
back the product. Contact American DJ, Inc. Service Department at 800-322-6337. Send the product
only to the American DJ, Inc. factory. All shipping charges must be pre-paid. If the requested repairs or
service (including parts replacement) are within the terms of this warranty, American DJ, Inc. will pay
return shipping charges only to a designated point within the United States. If the entire instrument is
sent, it must be shipped in it’s original package. No accessories should be shipped with the product. If
any accessories are shipped with the product, American DJ, Inc. shall have no liability whatsoever for
loss of or damage to any such accessories, nor for the safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is
modified in any manner which American DJ, Inc. concludes, after inspection, affects the reliability of
the product; if the product has been repaired or serviced by anyone other than the American DJ, Inc.
factory unless prior written authorization was issued to purchaser by American DJ, Inc.; if the product
is damaged because not properly maintained as set forth in the instruction manual.
D.
This is not a service contract, and this warranty does not include maintenance, cleaning or
periodic check-up. During the period specified above, American DJ, Inc. will replace defective parts
at its expense with new or refurbished parts, and will absorb all expenses for warranty service and
repair labor by reason of defects in material or workmanship. The sole responsibility of American DJ,
Inc. under this warranty shall be limited to the repair of the product, or replacement thereof, including
parts, at the sole discretion of American DJ. All products covered by this warranty were manufactured
after January 1, 1990, and bear identifying marks to that effect.
E.
American DJ, Inc. reserves the right to make changes in design and/or improvements upon
its products without any obligation to include these changes in any products theretofore manufactured. No warranty, whether expressed or implied, is given or made with respect to any accessory
supplied with products described above. Except to the extent prohibited by applicable law, all implied
warranties made by American DJ, Inc. in connection with this product, including warranties of merchantability or fitness, are limited in duration to the warranty period set forth above. And no warranties, whether expressed or implied, including warranties of merchantability or fitness, shall apply to
this product after said period has expired. The consumer’s and/or Dealer’s sole remedy shall be such
repair or replacement as is expressly provided above; and under no circumstances shall American DJ,
Inc. be liable for any loss or damage, direct or consequential, arising out of the use of, or inability to
use, this product. This warranty is the only written warranty applicable to American DJ and American Audio Products and supersedes all prior warranties and written descriptions of warranty terms and
conditions heretofore published.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
• All American Audio Products = 1-year (365 day) Limited Warranty (except V-Plus Series Amplifiers)
• All American Audio V-Plus Series Amplifiers = 3-year (1095 day) Limited Warranty
• American DJ Lighting and American DJ Branded Products = 1-year (365 day) Limited Warranty (Such
as: Special Effect Lighting, Intelligent Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines,
Mirror Balls, Par Cans, Trussing, Lighting Stands etc. excluding Laser Products, lamps, and Star Tec
Series)
• American DJ Laser Products and Star Tec Products = 90-Day Limited Warranty
• American DJ L.E.D. Products = 3-year (1095 day) Limited Warranty (excluding motors, PCB boards,
and power supplies, which have a 1-year (365 day Limited Warranty) and batteries which have a 180
day limited warranty).
©American
DJ Supply® - www.americandj.com - Inno Color Beam 12 User Manual Page 19
Inno Color Beam 12
Specifications
SPECIFICATIONS:
Voltage: 120V~240V 50Hz/60Hz
LEDs:
12 x 3W Cree LEDs (3 Red,
3 Green, & 3 Blue)
Power Consumption:
53W
Beam Angle:
15 Degrees
Fuse:7Amp
Weight: 12lbs./ 5Kgs.
Dimensions:
9” (L) x 8.75” (W) x 12” (H)
224 x 219 x 302mm
Colors:
RGB Color Mixing
DMX Channels:
2 DMX Channel Modes: 9 or 16 Channels
Working Position: Any safe working position
Warranty:
3 Year (1095 days)
Auto Sensing Voltage: This fixture contains a electronic bal-
last, which will auto sense the voltage when it is plugged into the
power source.
Please Note: Specifications and improvements in the design of
this unit and this manual are subject to change without any prior
written notice.
©American DJ Supply
American DJ World Headquarters:
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: 323-582-2650 / Fax: 323-725-6100
Web: www.americandj.com / E-mail: info@americandj.com
American DJ Europe
Junostraat 2
6468 EW Kerkrade
Netherlands
service@adjgroup.eu / www.americandj.eu
Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99