Viking VWCI1240GRSS Troubleshooting guide

Viking Use & Care Manual
Viking Range Corporation
111 Front Street
Greenwood, Mississippi 38930 USA
(662) 455-1200
For product information
call 1-888-VIKING1 (845-4641),
or visit the Viking Web site at
vikingrange.com
15”W./24”W.
Undercounter Refrigeration
F20867A EN
(061912)
Congratulations
Table of Contents
Congratulations and welcome to the elite world of Viking ownership.
We hope you will enjoy and appreciate the care and attention we have
put into every detail of your new, state-of-the-art undercounter
refrigeration.
Important Safety Instructions ___________________________________4
Electronic Controls____________________________________________5
Temperature Controls _________________________________________6
Using the Unit________________________________________________8
Wine Rack Finishing _________________________________________10
Interior Light ________________________________________________12
Checking Temperature _______________________________________13
Winterizing Outdoor Units ____________________________________14
Preparing for Spring Use _____________________________________15
Cleaning ___________________________________________________16
Troubleshooting _____________________________________________17
Service & Registration________________________________________20
Warranty ___________________________________________________21
Your Viking appliance is designed to offer years of reliable service. This
Use and Care Guide will provide you with the information you need to
become familiar with your undercounter refrigeration unit’s care and
operation.
Your complete satisfaction is our ultimate goal. If you have any
questions or comments about this product, please contact the dealer
from whom you purchased it, or contact our Consumer Support Center
at 1-888-VIKING1.
We appreciate your choice of a Viking undercounter refrigeration unit
and hope that you will again select our products for your other major
appliance needs.
For more information about the complete and growing selection
of Viking products, contact your dealer or visit us online at
vikingrange.com.
2
3
Important Safety Instructions
Electronic Controls
• Before beginning, please read these instructions completely
and carefully.
• DO NOT remove permanently affixed labels, warnings, or
plates from the product. This may void the warranty.
• Please observe all local and national codes and ordinances.
• Please ensure that this product is properly grounded.
• The installer should leave these instructions with the
consumer who should retain for local inspector’s use and for
future reference.
Displays target set point
Activates Sabbath Mode
WARNING
Increases temperature when changing set
point; Shows maximum stored temperature
when pressed alone.
To reduce the risk of fire, electric shock, or injury when using your unit,
follow these basic precautions:
• Read all instructions before using the unit.
• Never allow children to operate, play with, or crawl inside the unit.
• Never clean unit parts with flammable fluids. The fumes can create a
fire hazard or explosion.
• Always turn the power off to change light bulbs, clean, or service the
unit.
Decreases temperature when changing set
point; Shows minimum stored temperature
when pressed alone.
On/Off Switch
FOR YOUR SAFETY
DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE
VAPORS AND LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER
APPLIANCE. THE FUMES CAN CREATE A FIRE HAZARD OR
EXPLOSION.
It is your responsibility to be sure your undercounter
refrigeration unit is:
• located so the front is not blocked to restrict incoming or
discharge air flow.
• properly leveled.
• located in a well ventilated area.
• connected to the proper kind of outlet, with the correct
electric supply and grounding. A 115V, 60 Hz, 15 amp fused
electrical supply is required. Note: Time delay fuse or circuit
breaker is recommended.
• not used by anyone unable to operate it properly.
• used only for its intended purpose.
• properly maintained.
Light Switch
LED Indicators
LED
FUNCTION
Cooling ON
An alarm is occurring
(See troubleshooting for alarm codes)
Light ON
°C/°F
Measurement Unit
°C/°F
•SAVE THESE INSTRUCTIONS•
4
5
Electronic Controls
Electronic Controls
Temperature Control Panel
The controller is located inside of the unit. The display will read
OFF when the unit is off and will show temperature when the
unit is ON.
IMPORTANT: The LED display is reading actual air temperature
not product temperature. Under these conditions, an air
temperature swing does not change the actual product
temperature. Product temperature remains at a very stable
temperature.
Product Temperature Set Points and Ranges
All Refrigerator
Refrigerated Drawer
Beverage Center
Wine Center
38°F
38°F
42°F
55°F
Range:
Range:
Range:
Range:
32°F
32°F
32°F
44°F
to
to
to
to
39°F
39°F
48°F
68°F
To view the SET point:
1. Press and release the SET button. The display will show the
set point value.
2. Press and release the SET button or wait for 5 seconds to
display the actual temperature again.
Sabbath Mode
To activate SABBATH mode, press the Light button to turn off
the light. Then press the SAB button.
When in Sabbath mode:
• The display will be switched off (with the exclusion of the
measurement temperature icon LED);
• The regulation will keep on working normally;
• The digital inputs will be deactivated (they will not work
during SABBATH MODE);
• After any alarm condition the display will be switched on,
coming back to the OFF mode at the end of the alarm
condition;
• The keyboard will be deactivated with the exclusion of the
SAB button.
To exit the SABBATH mode, press the SAB button. The display
will turn on, but the light will remain off until the next time the
door is opened.
To change the SET point:
1. Press the SET button for 3 seconds to change the set point
value.
2. The value of the set point will be displayed and the “°C” or
“°F” LED will start blinking.
3. To change the set point value, press the UP or DOWN
buttons within 10 seconds.
4. To store the new set point value, press the SET button
again or wait 10 seconds.
To lock the control:
1. Press the UP+DOWN buttons simultaneously for 3 seconds.
2. The “PoF” message will be displayed and the keyboard will
be locked. At this point it will only be possible to see
the set point, the MAX or the MIN temperature stored.
3. If a button is pressed more than 3 seconds, the “PoF”
message will be displayed.
To unlock the control:
1. Press the UP and DOWN buttons simultaneously for 3
seconds until the “Pon” message is displayed.
6
7
Using the Unit
Using the Unit
Loading Product
IMPORTANT: Before storing perishables, allow unit to run for a
minimum of 24 hours to allow temperature stabilization after
start-up.
When loading items into unit, do no block internal louvers and
fan guard openings or performance will be decreased.
Shelving
IMPORTANT: To achieve maximum performance, interior louver
openings and fan guard openings should never be obstructed.
DANGER
To remove
brackets,
remove shelf,
lift front of
bracket to
disengage the
front key slot,
and pull
forward to
disengage the
rear key slot.
All Refrigerator
The single door unit comes standard with two adjustable, full
extension, pullout shelves. Shelving positions are adjustable.
Press tabs and
pull out shelf
Wine Center
The single door unit comes standard with five full extension
black vinyl coated wine racks capable of storing 20 total wine
bottles (15” models) or 40 total wine bottles (24” models).
Shelves are removable and adjustable to accommodate
oversized (magnum) bottles.
CAUTION
Completely empty the drawer before removing.
Beverage Center
Removing drawers from Refrigerated Drawer Unit
The single door unit comes standard with two full extension
black vinyl coated wine racks and one full extension pullout
shelf allowing for storage of both wine and beverages. Shelving
positions are adjustable.
Full-extension Drawers – Pull the drawer out to its farthest
point. Locate the tabs in the middle on both sides of the
extenders. Press left tab up and right tab down; pull drawer
out. To return drawer, first push both extenders completely in
then line up the shelf grooves and slide easily into the unit.
Adjusting Full Extension Shelving
1. Pull the shelf out to its farthest position. Locate the tabs in
the middle of both extenders. Press left tab up and right tab
down and pull shelf out.
2. Reposition each bracket separately. Grasp the middle of the
bracket, pull the front end up and out, then forward to remove.
3. Place bracket at the desired position. Push the rear hook into
the rear key slot. Set front of bracket on the wall hook.
FOR YOUR SAFETY
4. Repeat for other bracket(s).
5. Push extenders completely into the unit. Align the shelf
grooves with the extenders and slide completely into the unit.
8
9
Wine Rack Finishing
Wine Rack Finishing
Wooden Rack Trim Finishing
All wine racks come with unfinished solid hardwood fronts
which can be replaced with other wood to match your
cabinetry. See following illustrations for wine rack face details.
The unfinished faces may be finished and sealed. In many cases
stains and/or finishes have odors that may be objectionable in
an enclosed area. To remove the front wood-face from the wine
shelf, simply pull out the wine shelf and remove the fasteners,
finish as desired and re-install with fasteners.
24”W. Wooden Wine Rack Trim Design
8-17/32”
(21.7 cm)
33/64”
(1.3 cm)
5/8”
(1.6 cm)
8-17/32”
(21.7 cm)
8”
(20.3 cm)
4-1/32”
(10.2 cm)
A
2 NOTE:
LIP AND SPUR DRILL BIT
ARE ACCEPTABLE
4-1/64”
(1.6 cm)
1/16”
(0.2 cm)
TYP
B
BREAK ALL
OUTSIDE
EDGES.
DETAIL A
SCALE 1.5 : 1
1/8” (0.3 cm) TYP
33/64”
(1.3 cm)
1 3/8”
(1.0 cm)
1-17/32”
(3.9 cm)
7-1/4”
(18.4 cm)
15”W. Wooden Wine Rack Trim Design
4-1/32”
(10.2 cm)
4-1/64”
(1.6 cm)
DETAIL B
SCALE 1.5 : 1
2 NOTE:
LIP AND SPUR DRILL BIT
ARE ACCEPTABLE
1 3/8”
(1.0 cm)
1/8” (0.3 cm) TYP
1/16”
(0.2 cm)
TYP
1/4”
(0.6 cm)
45°
1-1/2”
(3.8 cm)
1/4”
(0.6 cm)
1/4”
(0.6 cm)
3/8” 1
(1.0 cm)
45°
BREAK ALL OUTSIDE
EDGES.
1-1/2”
(3.8 cm)
18-21/64”
(46.6 cm)
9-21/64”
(23.7 cm)
10
11
1/4”
(0.6 cm)
3/8” 1
(1.0 cm)
Interior Light
Checking Product Temperature
Interior Light
To accurately check the temperature of the product stored in a
refrigerated compartment, insert an accurate thermometer into
a plastic (non-breakable) bottle, partially filled with water.
Tighten the bottle cap securely.
The unit is equipped with an interior light that is illuminated
when the door is opened. The cabinet also comes standard
with a display light function located on the control panel for
displaying your products through a glass door. To use display
lighting, press the Light button twice. On the first press, the
light will turn off. On the second press, the light will turn back
on and be in display lighting mode. Do not use the display
light function with a solid door product. If the display light is
left on for an extended period of time, it may increase the
cabinet temperature, especially at the top and cause the
refrigeration system to run longer.
Light Bulb Replacement
NOTE: Please contact your Viking Range parts distributor or
dealer to order the LED light bulb.
To replace light bulb, unscrew the bulb counterclockwise and
replace with new bulb.
12
Place the bottle in the desired area for 24 hours. Refrain from
opening the unit during the testing period. After 24 hours,
check the temperature of the water. Adjust the control settings
if necessary and re-test.
Your units are pre-set in order to achieve the recommended
temperature range when installed in a 70°F ambient room
temperature. Factors, which affect the internal temperatures of
the refrigerated cabinet, include:
•
•
•
•
•
•
•
•
•
Temperature setting
Room temperature where installed
Number of times the door is opened and closed
Length of times the door is opened and closed
Length of times the door is left open
Style of door installed
Door gasket sealing and condition
Amount of time the internal light is illuminated
Installation in direct sun light or near a heat source
13
Winterizing Outdoor Units
Preparing for Spring Use
This process should occur when the daily low temperature is
at or below the set point temperature in the unit.
This process should occur when the daily low temperature is
at or above the set point temperature in the unit.
1.
2.
3.
4.
5.
6.
7.
Turn unit to OFF position by pressing the OFF button
on the controller. The controller displays the word OFF
(If power cord is accessible, unplug the cabinet. If not,
turn off the circuit breaker to the receptacle the cabinet
is plugged into.)
Remove all contents from the unit.
Remove the kickplate from the unit.
Clean the condensor by using a vacuum cleaner
to remove the loose debris (dirt, leaves, etc.) that may
have gotten inside the kickplate.
Reattach the kickplate.
Clean the interior using Stainless Steel Cleaner and
Polish.
Clean the exterior using Stainless Steel Cleaner and
Polish.
1.
2.
3.
4.
5.
6.
7.
Plug the unit into the electrical receptacle.
Press the OFF button one time to turn the unit ON. The
controller will read the actual temperature inside the
unit on the display. It will soon begin the cooling
process to bring the unit to the set temperature.
Remove the kickplate from the unit.
Check the condensing unit to ensure it is clear of loose
debris, clean as necessary with vacuum cleaner.
Reattach the kickplate to the unit.
Clean the interior using Stainless Steel Cleaner and
Polish.
Clean the exterior using Stainless Steel Cleaner and
Polish.
NOTE: Do not place a cover over the unit.
NOTE: While not required, you may choose to remove the unit
from the outdoor location and store indoors.
WARNING
Leaving your product operating in temperatures lower than those
recommended will void the warranty.
14
DANGER
15
DANGER
WARNING
Cleaning
Troubleshooting
Cleaning
Before Calling for Service
To clean stainless steel exterior or interior surfaces, use a soft,
non-abrasive stainless steel cleaner to wipe down these
surfaces. Glass door panels can be cleaned using any standard
glass cleaner available on the market today.
If the unit appears to be malfunctioning, read through
NORMAL OPERATION first. If the problem persists, check the
TROUBLESHOOTING GUIDE. Locate the problem in the guide
and refer to the cause and its remedy before calling for service.
The problem could be something, which can be solved without
a service call.
To clean interior and exterior non-metallic surfaces and
removable parts, wash with a mild solution of soap and
lukewarm water with a little baking soda. Rinse and dry
thoroughly. Avoid getting water on lights, controllers, fan
motors, and unfinished wood wine rack faces.
CAUTION
DANGER
DO NOT use abrasive cleaners or cloths on any of the interior or exterior
surfaces or removable parts.
WARNING
ELECTROCUTION HAZARD!!
Never attempt to repair or perform maintenance on the unit until the main
electrical power has been disconnected.
Problem
Solution
No interior light
• Check to ensure bulb is tight.
• Check to ensure bulb is not burned out.
Light stays on when
door is closed
• Manual ON/OFF light switch is turned ON.
• Check to ensure door switch is making
contact with door.
Noise during
operation
• Certain sounds are normal. Soft sounds
from the compressor, fan motor and valves
will be heard.
Controller display is
flashing “P1”
• There is a thermostat probe failure.
Controller display is
flashing “HA”
• The internal compartment temperature has
exceeded the high temperature alarm
preset value for over 30 minutes.
• Check to ensure door is closed.
• Check for door gasket seal.
• Product was just installed.
• Check to ensure condenser is clean.
• Check to ensure kickplate is unobstructed.
• Surrounding ambient temperature has
changed dramatically.
• Check to ensure interior light is OFF.
Condenser Cleaning
WARNING
For cleaning the condenser and other routine maintenance, shut off
electricity to the unit.
In all instances, you should clean the condenser area every
three months. The condenser is located behind the kickplate.
To clean the condenser remove the kickplate and use a soft
bristle brush and vacuum to remove dust and lint. Avoid
damaging or crushing the condenser fins or tubing. Upon
completion, re-install the kickplate.
FOR CAUTION
YOUR SAFETY
Failure to clean the condenser could result in temperature loss or
mechanical failure or damages. Clean this area every three months.
DANGER
DANGER
16
17
Troubleshooting
(cont.)
Troubleshooting
Problem
Solution
Problem
Solution
Controller display is
flashing “DA”
• The door has been left ajar.
• Check to ensure door is closed.
Controller display is
flashing “LA”
• The internal compartment temperature has
exceeded the low temperature alarm preset
value for over 30 minutes.
• Check to ensure door is closed.
• Check for door gasket seal.
• Surrounding air temperature has changed
dramatically.
The refrigeration
system runs for long
periods of time
• Check to ensure the condenser area is
clean and free of obstructions.
• Check to ensure the door has not been
open for a long time or more frequent door
openings aren’t occurring.
• Check to ensure warm product hasn’t just
been placed in the cabinet.
• On hot days and in warm room
temperatures the system will run long.
Controller display is
flashing “EE”
• The controller has a data or memory failure.
Condensation forms
inside the refrigerated
compartments
The refrigerated
cabinet isn’t running
• Check to ensure
the unit.
• Check to ensure
or fuse is on.
• Check to ensure
on.
• Check to ensure
clean.
• This is normal during high humidity and
frequent door openings.
• Check to ensure door is closed and sealing
properly.
Condensation forms
on the outside of the
unit
• During periods of high humidity some
condensation might appear on outside
surfaces. The condensation will disappear
when the humidity drops. Meanwhile, be
sure doors are closing and sealing properly.
If condensation persists, contact your
local Viking authorized servicer.
there is electrical power to
your home circuit breaker
your ON/OFF key pad is
your condenser area is
The refrigerated
compartment is
warmer than usual
• Check to ensure your control is set properly.
• Check to ensure the light is not staying on.
• Check to ensure your condenser area is
clean and free of obstructions.
• Check to ensure the door has not been
open for a long time or more frequent door
openings aren’t occurring.
• Check to ensure the internal louvers and fan
guard openings aren’t obstructed.
• Check to ensure warm product hasn’t just
been placed in the cabinet.
The refrigerated
compartment is
colder than usual
• Check to ensure your control is set properly.
• Check to ensure your door is closing and
sealing properly.
• Check to ensure the ambient temperature is
within the normal operating range.
18
When pressing the UP • If the UP button is pressed without pressing
button, the display
the SET button, the MAX stored
shows a “Hi” message
temperature will be displayed. Press the UP
followed by a
button again or wait 5 seconds for the
temperature that does
normal temperature to be displayed. To
not match the set
reset the MAX temperature, press and hold
point.
the SET button until the message “rSt”
starts blinking. Release the SET button and
the new stored value will be the current
temperature. Frequent and/or extended
door openingsmay cause a higher than
expected MAX temperature.
• If the DOWN button is pressed without
When pressing the
DOWN button, the
pressing the SET button, the MIN stored
display shows a “Lo”
temperature will be displayed. Press the
message followed by a DOWN button again or wait 5 seconds for
temperature that does
the normal temperature to be displayed. To
not match the set
reset the MIN temperature, press and hold
point.
the SET button until the message “rSt”
starts blinking. Release the SET button and
the new stored value will be the current
temperature.
19
Service & Registration
Warranty
If service is required after checking the troubleshooting guide, call your
Viking dealer or authorized service agency. The name of the authorized
service agency can be obtained from the dealer or distributor in your
area.
THREE YEAR FULL WARRANTY
Undercounter refrigeration and all of their components and accessories, except as detailed below*, are
warranted to be free from defects in material or workmanship under normal household use for a period of
three (3) years from the date of original retail purchase. Viking Range Corporation, warrantor, agrees to
repair or replace, at its option, any part which fails or is found to be defective during the warranty period
When you make a service call, be sure to have the following
information handy:
• Model Number
• Serial Number
• Date of Purchase
• Name of dealer from whom purchased
*Painted and decorative items are warranted to be free from defective materials or workmanship for a
period of ninety (90) days from the date of original retail purchase. ANY DEFECTS MUST BE REPORTED TO
THE SELLING DEALER WITHIN NINETY (90) DAYS FROM DATE OF ORIGINAL RETAIL PURCHASE.
SIX YEAR FULL WARRANTY
If you are unable to obtain the name of an authorized service agency,
or if you continue to have service problems, contact Viking Range
Corporation at (888) 845-4641 or write to:
Any sealed refrigeration system component, as listed below, is warranted to be free from defective
materials or workmanship in normal household use during the fourth through the sixth year from the date of
original retail purchase. Viking Range Corporation, warrantor, agrees to repair or replace, at its option, any
part which fails or is found to be defective during the warranty period.
Sealed Refrigeration System Components: Compressor, Evaporator, Condenser, Connecting Tubing,
Dryer/Strainer
TWELVE YEAR LIMITED WARRANTY
VIKING RANGE CORPORATION
PREFERRED SERVICE
1803 Hwy 82W
Greenwood, Mississippi 38930 USA
Record the following information indicated
below. You will need it if service is ever
required. The model and serial number for
your undercounter refrigeration unit are
located in the top right under the control
housing.
VRCI/FRCI/VBCI/FBCI/VWCI/FWCI/VRDI/FRDI UNDERCOUNTER
REFRIGERATION WARRANTY
(INDOOR MODELS)
Any sealed refrigeration system component, as listed above, which fails due to defective materials or
workmanship in normal household use during the seventh through the twelfth year from the date of original
retail purchase will be repaired or replaced, free of charge for the part itself, with the owner paying all other
costs, including labor.
NINETY (90) DAY RESIDENTIAL PLUS WARRANTY This warranty applies to applications where use of the
product extends beyond normal residential use. Examples are, but not limited to, bed and breakfasts, fire
stations, private clubs, churches, etc. This warranty excludes all commercial locations such as restaurants,
food service locations and institutional food service locations.
This warranty extends to the original purchaser of the product warranted hereunder and to each transferee
owner of the product during the term of the warranty.
Model and
Serial number
Model No. _________________________________________________________________________
Serial No. ___________________________________________________________________________
Date of Purchase__________________________________________________________________
Date Installed______________________________________________________________________
Dealer’s Name _____________________________________________________________________
Address _____________________________________________________________________________
________________________________________________________________________________________
If service requires installation of parts, use only authorized parts to
insure protection under the warranty.
This warranty shall apply to products purchased and located in the United States and Canada. Products
must be purchased in the country where service is requested. Warranty labor shall be performed by an
authorized Viking Range Corporation service agency or representative. Warranty shall not apply to damage
resulting from abuse, accident, natural disaster, loss of electrical power to the product for any reason,
alteration, improper installation, improper operation or repair or service to the product by anyone other
than an authorized Viking Range Corporation service agency or representative. Warranty shall not apply to
damage resulting from indoor units being used in outdoor situations. This warranty does not apply to
commercial usage. Warrantor is not responsible for consequential or incidental damage whether arising out
of breach of warranty, breach of contract, or otherwise. Some jurisdictions do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to
you.
Owner shall be responsible for proper installation, providing normal care and maintenance, providing proof
of purchase upon request, and making the appliance reasonably accessible for service. If the product or one
of its component parts contains a defect or malfunction during the warranty period, after a reasonable
number of attempts by the warrantor to remedy the defects or malfunctions, the owner is entitled to either
a refund or replacement of the product or its component part or parts. Replacement of a component part
includes its free installation. Warrantor’s liability on any claim of any kind, with respect to the goods or
services covered hereunder, shall in no case exceed the price of the goods or service or part there of which
gives rise to the claim.
WARRANTY SERVICE: Under the terms of this warranty, service must be performed by a factory authorized
Viking Range Corporation service agent or representative. Service will be provided during normal business
hours, and labor performed at overtime or premium rates shall not be covered by this warranty. To obtain
warranty service, contact the dealer from whom the product was purchased, an authorized Viking Range
Corporation service agent, or Viking Range Corporation. Provide model and serial number and date of
original purchase. For the name of your nearest authorized Viking Range Corporation service agency, call
the dealer from whom the product was purchased or Viking Range Corporation. IMPORTANT: Retain proof
of original purchase to establish warranty period.
Keep this manual with your refrigerator for future reference.
20
21
Warranty
Warranty
The return of the Owner Registration Card is not a condition of warranty coverage. You, however, should
return the Owner Registration Card so that Viking Range Corporation can contact you should any question
of safety arise which could affect you.
VRCO/VRDO UNDERCOUNTER REFRIGERATION WARRANTY
(OUTDOOR MODELS)
ONE YEAR FULL WARRANTY
Any implied warranties of merchantability and fitness applicable to the above described undercounter ice
machine are limited in duration to the period of coverage of the applicable express written limited
warranties set forth above. Some jurisdictions do not allow limitations on how long an implied warranty
lasts, so the above limitation may not apply to you. This warranty gives you specific rights, and you may
also have other rights which may vary from jurisdiction to jurisdiction.
Undercounter refrigeration and all of their components and accessories, except as detailed below*, are
warranted to be free from defects in material or workmanship under normal household use for a period of
one (1) year from the date of original retail purchase. Viking Range Corporation, warrantor, agrees to repair
or replace, at its option, any part which fails or is found to be defective during the warranty period
*Painted and decorative items are warranted to be free from defective materials or workmanship for a
period of ninety (90) days from the date of original retail purchase. ANY DEFECTS MUST BE REPORTED TO
THE SELLING DEALER WITHIN NINETY (90) DAYS FROM DATE OF ORIGINAL RETAIL PURCHASE.
FIVE YEAR LIMITED WARRANTY
Any sealed refrigeration system component, as listed above, which fails due to defective materials or
workmanship in normal household use during the second through the fifth year from the date of original
retail purchase will be repaired or replaced, free of charge for the part itself, with the owner paying all other
costs, including labor.
NINETY (90) DAY RESIDENTIAL PLUS WARRANTY This warranty applies to applications where use of the
product extends beyond normal residential use. Examples are, but not limited to, bed and breakfasts, fire
stations, private clubs, churches, etc. This warranty excludes all commercial locations such as restaurants,
food service locations and institutional food service locations.
This warranty extends to the original purchaser of the product warranted hereunder and to each transferee
owner of the product during the term of the warranty.
This warranty shall apply to products purchased and located in the United States and Canada. Products
must be purchased in the country where service is requested. Warranty labor shall be performed by an
authorized Viking Range Corporation service agency or representative. Warranty shall not apply to damage
resulting from abuse, accident, natural disaster, loss of electrical power to the product for any reason,
alteration, improper installation, improper operation or repair or service to the product by anyone other
than an authorized Viking Range Corporation service agency or representative. Warranty shall not apply to
damage resulting from indoor units being used in outdoor situations. This warranty does not apply to
commercial usage. Warrantor is not responsible for consequential or incidental damage whether arising out
of breach of warranty, breach of contract, or otherwise. Some jurisdictions do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to
you.
Owner shall be responsible for proper installation, providing normal care and maintenance, providing proof
of purchase upon request, and making the appliance reasonably accessible for service. If the product or one
of its component parts contains a defect or malfunction during the warranty period, after a reasonable
number of attempts by the warrantor to remedy the defects or malfunctions, the owner is entitled to either
a refund or replacement of the product or its component part or parts. Replacement of a component part
includes its free installation. Warrantor’s liability on any claim of any kind, with respect to the goods or
services covered hereunder, shall in no case exceed the price of the goods or service or part there of which
gives rise to the claim.
WARRANTY SERVICE: Under the terms of this warranty, service must be performed by a factory authorized
Viking Range Corporation service agent or representative. Service will be provided during normal business
hours, and labor performed at overtime or premium rates shall not be covered by this warranty. To obtain
warranty service, contact the dealer from whom the product was purchased, an authorized Viking Range
Corporation service agent, or Viking Range Corporation. Provide model and serial number and date of
original purchase. For the name of your nearest authorized Viking Range Corporation service agency, call
the dealer from whom the product was purchased or Viking Range Corporation. IMPORTANT: Retain proof
of original purchase to establish warranty period.
The return of the Owner Registration Card is not a condition of warranty coverage. You, however, should
return the Owner Registration Card so that Viking Range Corporation can contact you should any question
of safety arise which could affect you.
Any implied warranties of merchantability and fitness applicable to the above described undercounter ice
machine are limited in duration to the period of coverage of the applicable express written limited
warranties set forth above. Some jurisdictions do not allow limitations on how long an implied warranty
lasts, so the above limitation may not apply to you. This warranty gives you specific rights, and you may
also have other rights which may vary from jurisdiction to jurisdiction.
22
23