Craftsman 139.53671SRT1 Owner`s manual

Owner's
Manual
Model No.
139.53661SRT1
139.53671SRT1
139.53672SRT1
139.53673SRT1
139.53674SRT
139.53677SRT1
/
For Residential Use
Only
CRAFTSMRN®
GARAGE DOOR OPENER
Caution:
Read and follow all
safety rules and
operating instructions
before first use of this
product.
Fasten the manual
near the garage door
after installation.
• Safety Precautions
• Assembly
• Installation
• Adjustment
• Care and Maintenance
• Operation
• Troubleshooting
• Parts List
Complies wib_ UL 325
regulations effective
January 1, 199:3
Sears,
Roebuck
and Co., Hoffman
Estates, IL 60179 U.S.A.
Contents
Page
A review of safety alert symbols ................................. 2
Contents
Page
Install the light and lens ................................................. 19
You'll need tools.......................................................... 3
Attach emergency release rope and handle ................. 19
Safety informationregarding garage door locks
and ropes .................................................................. 3
Safety reversing sensor information.............................. 21
Electrical requirememts................................................. 20
Testing your garage door for sticking,binding
and balance............................................................... 3
Illustretionof sectional door installaUon..................... 4
Install the safety reversing sensor........................... 22, 23
Fasten door bracket (sectional door) ............................ 24
F:asten door bracket (one-piece door) ........................... 25
Illustration of one-piece door installation...................5
Connect door arm to trolley (sectional door) ................. 26
Carton inventory.......................................................... 6
Hardware inventory.:................................................... 7
Assembly section - pages 8 - 11
Assemble T-rail ......................................................... 8
Attach cable pulley bracket ....................................... 8
Instail trolley ...?......................................................... 9
Fasten T-reJlto opener ............................................. g
Install chin/cable ................................................... 10
Attach sprocketcover ............................................. 10
Tighten b_echain and cable ................................... 11
Installation section - pages 11 - 27
Installationsafety inetmctions................................. 11
Determine header bracket location
Sectional door ....................................................... 12
One-piece door ..................................................... 13
Install the header bracket ....................................... 14
Attach the T-raJ1to header bracket ......................... 15
Position the opener................................................. 16
Hang the opener ..................................................... 17
Install the door control............................................ 18
Connect door arm to trolley (one-piece door) ............... 27
Adjustment section - pages 28- 30
Travel limit adjustments................................................. 28
Force adjustments ......................................................... 29
Test the safety reversingsensor ................................... 30
Test the safety reverse system .................................... 30
Operation safety instructions............................. ;.............31
Care of your opener ......................................................... 31
Maintenance schedule .................................................... 31
Operation of your opener ................................................ 32
Receiver and remote control programming .................... 33
Having a problem? .................................................... 34, 35
Repair parts, rail assembly .............................................. 36
Repair parts, installat_t .................................................. 36
Repair parts, opener assembly ....................................... 37
Accessories ...............................................
38
Index ................................................................................
39
How to order repair parts................................................. 40
Maintenance agreement .................................................. 40
Warranty ..........................................................................
40
Start by reviewing these important safety alert symbols
Mechanical
Electrical
When you see this Safety Symbol on the following pages, It will alert you to the possibility of damage
to your garage door and/or the garage door opener If you do not comply with the corresponding
instructions. Read the instructions carefully.
This garage door opener is designed and tested to offer safe service provided it Is Installed, operated,
maintained and tested in strict accordance with the safety instructions contained in this manual.
2
You'll Need Tools
During assembly, installation and adjustment of the opener, instructions will call for hand tools shown below.
Pencil
Oooel
Lev_
OOO O
Hack
Saw
Ta_e Measure
W3re Cutters
ClawHammer
3116", 5116" awJ
5/32" Drill Bits
_rewdl'iver
Step_adder
Adjustable End Wrench
An unbalanced garage door might not reverse
when required and someone under the door
could be seriously injured or killed.
If your garage door binds, sticks or is out of
balance, call for professional
garage door
service. Garage doors, door springs, cables,
pulleys, brackets and their hardware are under
extreme tension and can cause serious Injury
or death. Do not try to loosen, move or adjust
them yourself!
Ropes left on a garage
door could cause
someone to become entangled
and killed.
Remove all ropes connected to the door before
installing and operating the opener.
To avoid damage to the garage door and
opener, disable locks before installing and
operating the opener. Use a wood screw or nail
to hold locks in the "open" (unlocked) position.
Operation at other than 120V 60 Hz will cause
opener malfunction
and damage.
Before you begin, complete the following test to
make sure your door is balanced, and is not
sticking or binding:
• Lift the door about halfway as shown. Release the
door. It should stay in place, supported entirely by
its springs.
Identify the type and height of your door and any
special conditions that exist and any additional
materials that may be required by referring to the
lists on page 4 or page 5.
• Raise and lower the door to see if there is any
binding or sticking.
,.,j
Before you begln, survey your garage area to
see whether any of the conditions below apply
to your installation.
FINISHED CEILING
SuI_
bracket &
fastlming hardware
Horizontal and vertical reinforcement
iS needed to_'llghtw_ght _
doors
(fiberglass. steel, akJminum, door v_th glass panels, etc.).
See page 24 for details.
Seg page 17.
Slack in ChainTen6ion
is NormalWhen
Garage Dooris Closed "
AccellDoor
o
Closed PeeWon
Cab_ Puny
Bracket Troaey
Cable
Rail Assembly
I
Based on your particular requirements, there are
several installation steps which might call for
matedals and/or hardware not included in the carton.
Emergency
Release
Roge& Hand_
• Step 1, page 12 - Look at the wall or ceiling above
the garage door. The header bracket must be
securely fastened to structural supports.
• Step 5, page 17 - Do you have a finished ceiling in
your garage? If so, a support bracket and
additional fastening hardware may be required.
• Safety reversing sensor, page 21 - Depending
upon garage construction, wood blocks may need
to be fastened to mounting locations before
sensors are installed.
, • The opener can be installed within 2 feet of the left or
right of the door center if there is a torsion spdng or
center bearing plate in the way of the header
bracket or door bracket area. If your door has
extension springs, the opener must be installed
in the center of the door. See pages 12 and 24.
• Step 10, page 22 - Alternate floor mounting of the
safety reversing sensor will require hardware not
provided.
• Step 11, page 24 - Do you have a steel, aluminum,
fiberglass or glass panel deer?. If so, horizontal
and vertical reinforcement is required.
• Do you have an access door in addition to the
garage door? If not, Model 53702 Emergency
Key Release is required. See page 38.
• Look at the garage door where it meets the floor.
It must close on the floor all the way across.
Other-wise, the safety reveree system may not
work properly. See page 30. Floor or door should
be repaired.
• If your door is more than 7 feet high, see the rail
extension kits avaJlable on page 38.
You may find It helpful to refer back to this page as you proceed with the Installation of your opener.
4
One-Piece
Before you begin, survey your garage ares to
see whether any of the conditions below apply
to your installation.
Door Without
Track
FINISHED CEILING
Support bracket
& faslening
in chain thns_on
is normal when
hardware is required.
See page t7.
garage door is dosed.
Header
Wa!l
Closed Position
Cable
/
Pultey Bracket
Bracket
O
Cable
Trolley
T-rail
DoorSrac_xet
Release
Door
Arm
Coot
) betweenfloorand bottom ReversingSensor
of doormustnot exceed I/4".
Safety Reversir_ Sensor
Based on your particular requirements, there are
several installation steps which might call for
materials and/or hardware not included in the carton.
One-Piece
Door With Track
• Step 1, page 13 - Look at the wall or ceiling above
the garage door. The header bracket must be
securely fastened to structural supports.
• Step 5, page 17 - Do you have a finished ceiling in
your garage? If so, a support bracket and
additional fastening hardware (not provided) may
be required.
• Safety reversing sensor, page 21 - Depending on
garage construction, wood blocks may need to be
securely fastened to mounting locations before
sensors are installed.
• Step 10, page 22 - Alternate floor mounting of the
safety reversing sensor will require hardware that
is not provided.
Safety
ReversingSensor
• Step 11, page 25 - Generally, a one-piece door
does not require reinforcement. If your door is
lightweight, you can refer to the information
relating to sectional doors on page 24.
Floormust be level
acrosswidth of door
Revering
Closed Position
Cable
Cable
Trolley
Chain
• Step 11, page 25 - Depending on your door's
construction, you might need additional mounting
hardware for the door bracket.
• Do you have an access door in addition to the
garage door?. If not, Model 53702 Emergency
Key Release is required. See page 38.
I mL"
Garage
--
• The gap between the bottom of the garage
door and the floor cannot exceed 1/4".
Otherwise, the safety reverse system may not
work properly. See page 30. The floor or the door
should be repaired.
_'//.I "saor
s_ig_t
_
P,ele=se
Door
You may find it helpful to refer back to this page as
you proceed with the Installation of your opener.
5
Carton Inventory
Your garage door opener is packaged in two cartons which contain all pads illustrated below. If anything is
missing, carefully check the packing material. Parts may be "stuck" in the foam. Hardware for assembly and
installation is shown on page 7.
Models 5366t (1), 53671 (1), 53672 (2).
53673 (2), 53674 (2). 53677 (2)
Models 53661, 53671, 53672
Models 53673, 53674
Model 53677
Standard
ContmlConsole
Premium
Control Console
Model 53674
Security+
Three-Function Remote Control
with Visor Clip
Cable
PulleyBmc_
2-Conductor
Bell Wire
White & Whi_e/l:_ed
T.P.ail
Center Section
T-Rail
EndSec.ons
Do<_Bracket
Sprod_etCover
"C"Wrap (2)
i: ::_s_si,_g
Carton
Safety Reversing Sensor
Hanging Brackets
MountingBcacket
w_ Squa_Ho_ t2)
¸7¸'¸
--
__
_' _¢;ng
Sa_ety
Re_n¢_ Seesor
Mount_g
BraCka
W_ Sk_(2)
Eye and 1 ReceivingEye)
::.3*_r=_c:or',_nitO & WhJle/t_ackBellWhl
attad'md
6
Stra_ Door
Am_
Set,on
Sel_arate
all hardware
from the packages
shown below, for the assembly
and installation
Assembly
Washered Screw
5/16"-183(1/2"(2)
(mounted in opener)
Hex Sorew
5/16".18xTir
(3)
Trolley'i_maded
in the rail carton
and the opener
carton, as
Carriage Bolts
114--20xl/2" (4)
Master Unk (2)
procedures.
Hardware
Nut
5/16".18
(5)
Shaft II1
Lock Washer
5/16" (4)
Lock NUt
1/4"-20_7/16" (4)
installation Hardware
_
Handle
Hex Screw
5/16"-18x7/8"
(4)
Gma_
0
5/16"-18xi-7/8"
(2)
Ring
Fastener (3)
Nut 5/16"-18(6)
L_JcWa_,her
5/16"(6)
IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII0
Carriage Boit
5/16"-18x2-1FZ'
6ABxl"
121
(2)
Dry Wall Anchors (2)
Insulated
Staples (I0)
Rope
o,
Clevis Fm
5/16"x2-3/4" (1)
Clevis Pin
5/16°xl"
(1)
Cle_s Pin
5/16"x1-114" (1)
Safety Reversing Sensor
installation Hardware
©
1/4xl-lt2" (4)
Carr_ge Bo_ts
1/4"-20xl/2"
(4)
@
_llllllllllllllltllllllllllllllllllliO
114-20x1-1/2"
(2)
Lock Nut
1/4"-20 (4)
#10-3_(3/_"
(4I
7
WingNut(2)
Assembly Section: Pages 8- 11
To avoid installation
difficulties,
do not run the garage
the T.rail & Attach
the Cable Pulley
until
Make sure bolt necks are
seated In the square
_
holes end rails are
_
aligned beforeyou
_
•
Assembly Step I
Assemble
door opener
.omenlo (Sas __
Bracket
instructed
_k A_P'-"-"-'_I'--_
t•
_• I
i right and wrong views). '_k
to do so.
. | /
J
•
'_
iImproper assembly can _
cause ]edo/trolley
operation,noise and/or
nuisancedoor reversals.
• Align the 3 T-rail sections on a fiat surface exactly
as shown. The end'sections are identical. Make
sure the "arrow label" on the center section is
pointing toward the door.
Right
Wrong
TRAIL BACK
(TO OPENER)
• Insert the carriage bolts so the square bolt necks
seat in the square holes in the T-rail end sections
end pass through the round holes in T-rail center
section. Assemble lock nuts, ensure alignment and
tighten.
1/4" LockNut
T.rail
(End Sec_on)
Brace
If T-rail is not assembled
EXACTLY as shown, trolley I
will not travel smoothly
]
along length of rail or it will
hit against the nuts.
I
Brace
T-raU
Hardware Shown Actual Size
Cab_p._/brackst
attaches
toFRONT
ENDofT-ral
©
SquareCarthage
B_t Hole=
Lod_
Nut
Cardage
Sob
114"* 20 x 7116"
1/4" -20 x 1/2"
(TOsoon)
• Positionthe cable pufley bracket on the front end of the
T-r_q as shown. Fasten sscurely with _e hardware.
.•
Hex Scrow
Nut
L_:k W_ner
5/16"- 18 x 7/8"
5/16" - 18
5/16"
cab*,Pamy
Brad_
Q
s
Right
L=_ Wuhw
5/16"
8
Wrong
sure to keep
bracket parallel
to the mllo
hen
tightening
Otherwlas,
the
the
scraws,
be
rail may bow
when opener is
operated.
Assembly
Hardware Shown
Actual Size
Step 2
Install the Trolley on the T-rail
©©
• Attach the threaded shaft to the trolley with the
lock washer and nuts as shown.
Lock Washer
5/16"
Nut
5/16" - 18
LockWasher
5/16"
Outer Nut
Tro!ley
Threaded
Shaft
InnerNut
5/16"
5/16"_
Trolley
TemporarySlop
Screwdriver
• As a temporary stop, insert a screwdriver into the
hole in the front end of the T-rail.
• Slide the trolley assembly along the rail to the
screwdriver stop.
If trolley hits against any nuts on the T-rail, the
bolts and nuts were attached from the wrong
side and must be reposltioned. Review Step 1.
Assembly
Fasten
Step 3
I
I
the T-rail to the Opener
• Place the opener on packing material to protect
the cover. For convenience, put a support under
the cable pulley bracket.
• Remove the (2) 5/16"-18xl/2 =washered screws
mounted in the top of the opener.
WasheredScrew
5/16".18xl/2"
• Align the holes in the back section of the T-rail with
the holes in the opener.
Hex Screw
5/16"-18x7/8"
• Fasten the rail with the (2) washered screws
previously removed. Tighten securely.
Cover
Protection
Remember to use only these screws! Any other
screws will cause serious damage to the opener.
• Insert a 5/16"-18x7/8" hex screw into the cover
protection bolt hole in the T-rail as shown. Tighten
securely with a 5/16" lock washer and nuL
Bolt Hole \,
T..raJl
(B=ckSection).
5/16"
NOTE: This screw prevents trolley over-travel.
Keep a 2" minimum between the trolley and this
screw when adjusting travel limits (see page 28).
NUt"
5/16"-18
Hardware Shown Actual Size
5/16" - 18 x 7/8"
5/16;
18
5/16"
9
\
u
Assembly
Step
4
WARNINQi
Install the Chain/Cable
&
Attach the Sprocket Cover
i
i
i
i
i
•
i
Serious injury can result if fingers become
entangled in moving opener sprocket. Attach
sprocket cover securely. Never operate opener
while your hand is near the opener sprocket.
Figure 2
c._.,.
Sprockel
Keep Chain and Cable
Taut When Dispensing
• Detach the cable loop from the carton and fasten it
to the trolley with a master link from the hardware
bag. See master link procedure, Figure 1.
Figure 3
• With the trolley against the screwdriver, dispense
the cable around the pulley.
• Proceed back around the opener sprocket,
Figure 2. Be sure sprocket teeth engage the
chain. Continue forward to the trolley
threaded shaft, Figure 3.
• Use the second master link to connect
the chain to the flat end of the shaft.
Check to make sure the chain Is
not twisted.
Master Link
C_p-On Spring , ,
Rat End
of Trolley
ThreadedShaft
Master
Link
Chain
• Remove the screwdriver.
T-rail
Trolley
m
t
_
Master
LinkBat
Figure I
Cable
PuJley
M_
Install Chain and Cadle
In This Direction
Unk Procedure:
Pushpinsof masterlink bar
throughcable loopand hole in
frontend oftrolley.Push cap
over pinsandpast notches.
Slide dip-on spdngover cap
and intonotchesunUIboth
pinsare securelyIo_ked.
Spmckat
Cov_
To attach the sprocket cover:
Front Tab Slot
• Insert the back tab in the opener slot. Squeeze the
cover slightly and insert the front tab in the slot on
the mounting plate.
Mortaring
Plate
lO
Assembly Step 5
Tighten
the Chain & Cable
I
Lock
Outer Nut
• Spin the inner nut and lock washer down the
threaded shaft, away from the trolley.
Washer
TO "ilghten Outer Nut --'_"_
• To tighten the chain, turn outer nut in the direction
shown. As you turn the nut, keep the chain
from twisting.
• When the chain is approximately 1/2" above the
base of the T-rail at its midpoint, re-tighten the
inner nut to secure the adjustment.
--
Inner Nut
lJ
T_olle_
Sprocket noise can result if chain is either too
loose or too tight.
When installation is complete, you may notice some
chain droop with the door closed. This is normal. If
the chain returns to the position shown when the
door is open, do not re-adjust the chain.
__
Inner Nut
Chin
1/2 Inch
Base of T-rail
NOTE: During future maintenance, ALWAYS
)ull the emergency release handle to disconnect
trolley before adjusting chain.
You have now finished assembling your garage door opener. Please read the following
warnings before proceeding to the installation section:
IMPORTANT INSTALLATION INSTRUCTIONS
To reduce the risk of severe injury or death to persons:
1. READ AND FOLLOW
ALL INSTALLATION
INSTRUCTIONS,
2. Install only on a properly balanced and lubricated garage door. An improperly balanced door
may not reverse and could result in severe Injury or death. Repairs to cables, spring assemblies
and other hardware must be made by a professional service person before Installing opener.
3. Disable all locks and remove all ropes connected to the garage door before Installing the opener.
Ropes connected to a garage door can cause entanglement and death.
4. If possible, Install door opener 7 feet or more above floor with the emergency
mounted 6 feet above the floor.
release handle
5. Do not connect the opener to power source until Instructed to do so.
6. Locate the Door Control within sight of the door at a mlnlmum height of 5 feet where small
children cannot reach and away from all moving parts of the door.
7. Install the User Safety Instruction Label on the wall adjacent to the door control and the
Maintenance Instruction Label in a prominent location on the inside of the garage door.
8. Upon compleUon of the Installation, the door must reverse when it comes in contact with a
one-inch high object or a 2x4 laid flat on the floor.
9. Do not wear watches, rings or loose clothing while installing or servlclng an opener. Jewelry or
• loose clothing can be caught in the mechanism of the garage door or the opener.
11
Installation
Installation
Determine
Section:
Pages 12-
WARN
Step I
Header
Bracket
Location
If the header bracket is not rigidly fastened to
a structural
support on the header wall or
ceiling, the safety reverse system may not
work properly (see page 30). The door might
not reverse when required, and could cause
serious injury or death.
The garage door springs,
cables, pulleys,
brackets and their hardware are under extreme
tension. Do not attempt to loosen, move or
adjust them yourself. Serious personal injury
or death could result. Call for professional
garage door service.
Installation procedures vary according to
garage door types. Follow the instructions
which apply to your door.
--
Header -Wal
27
Verlical
Guideline
2X4
Structural
• Close the door and mark the inside
vertical centedine of the garage door.
• Extend the line onto the header wall
above the door.
Remember, you can fasten the
header bracket within 2 feet of the
left or right of the door center onlyif
a torsion spring or center bearing
plate is in the way; or you can attach
it to the ceiling (refer to page 14)
when clearance is minimal. (It may
be mounted on the wall upside down
if necessary, to gain approximately
1/2".)
If you need to install the header bracket
on a 2x4 (on wall or ceiling), use lag
screws (not provided) to securely fasten
the 2x4 to structural supports as shown
here and on page 13.
Ceiling
Wal
• Open your door to the highest
point of travel as shown. Draw
an intersecting horizontal line
on the header wall 2" above
the high point. This height will
provide travel clearance for the
top edge of the door.
Door clearance brackets are
available for sectional doors
when headroom clearance is
less than 2". See accessory
page 38.
Tra_
N_
Track
Point
HighestPoint
ol Travel
Sectional door
with curved track
Proceed
Header
I
to Step 2, page 14.
12
One-piece door
with horizontal track
Read the Safety instructions
on page 12. They also apply to doors without
tracks.
Header Wall
2x4
• Close the door and mark the
inside vertical centedine of
your garage door. Extend the
line onto the header wall
above door.
If headroom clearance is
minimal, you can install the
header bracket on the ceiling.
See page 14.
OPTIONAL CEIUNG MOUNT
FOR HEADER BRACKET
• If you need to install the
header bracket on a 2x4 (on
wall or ceiling), use lag screws
(not provided) to securely
fasten the 2x4 to structural
supports as shown.
Header Wall
_,_1 I _
1
Highest point
of Trawd
Wall
Header
of Travel
Highestioint
Door
ii
Jamb
Hardware
One-piece door without track
pivot hardware
One-piece door without track
jamb hardware
EXAMPLE
• Open your door to the highest point of travel as
shown. Measure the distance from the top of the
door to the floor. Subtract the actual height of the
door. Add 8" to the remainder. (See Example),
Distance from top of door
(at highest point of travel) to floor ........................... 92"
Actual height of door .............................................
Remainder ................................................................
• Close the door and draw an intersecting horizontal
line on the header wall at the determined height.
If the total number of inches exceeds the height
available in your garage, use the maximum
height possible, or refer to page 14 for ceiling
installation.
Proceed
Add .........................................................................
+8"
Bracket height on header wall ...............................
12"
(Measure UP from top of CLOSED door.)
to Step 2, page 14.
13
-88.____."
4"
i
Install the Header Bracket
Installation
Step 2
You can attach the header bracket either to the
wall above the garage door, or to the ceiling.
Follow the Instructions which will work best for
your particular requirements,
I
Fasten the Header
• Center the bracket on the vertical guideline with
the bottom edge of the bracket on the horizontal
line as shown (with the arrow pointing toward the
ceiling).
Bracket to the Wall
• Mark either set of bracket holes (do not use the
holes designated for ceiling mount). Drill 3/16" pilot
holes and fasten the bracket securely to a structural
support with the hardware provided.
Wall
Mount_ Holes
"" "*Lag Screws
Spring "
f
The nail ho_ is for posilioning
\
only.
y_J must
use lagb'acket.
scrk=e_t
s 1o
mouni
the header
//
V
opt_lal
Wall Mounting
Ho_es
le_
Door
Hardware Shown Actual Size
Vertical
Center
Line
_16"-9XI-_"
Fasten the Header
Bracket
to the Ceiling
• Extend the vertical guideline onto the ceiling as
shown.
• Center the bracket on the vertical mark, no more
than 6" from the wall. Make sure the arrow is
pointing toward the wall. The bracket can be
mounted flush against the ceiling when clearance
is minimal.
• Mark holes designated for ceiling mount only• Drill
3/16" pilot holes and fasten bracket securely to a
structural support with the hardware provided.
Door
Spdng
Ceil!rigMountingHoles
"n_naJho_L_forpo=_k_ngonly.
You rnust use kRgscrews to motml_
the header btackel.
14
ii
Attach
the T-rail to the Header
Installation
Step 3
Bracket
[
• Position the opener on the garage floor below the
header bracket. Use packing material as a
protective base.
If the door spring is In the way you'll need help.
Have someone hold the opener securely on a
temporary support to allow the T-rail to clear the
spring.
Header
BW
//
//
//
• Position the cable pulley bracket against the header
bracket.
//
• Align the bracket holes and join with a clevis pin as
shown.
//
• Insert a ring fastener to secure.
Ring
Header
Fastener
Bracket
i
Clevis Pin
5/I 6"x2-3/4 •
Cable
Pulley
Bracket
Garage
Door
Temporary
Support
Hardware Shown Actual Size
0
Ckr_s P_
5/16" x 2-3/4"
©
Ring Fastener
15
Installation
Position
Step 4
the Opener
Follow instructions
type as Illustrated.
which apply to your door
i
A 2x4 laid flat is convenient for setting an Ideal
door-toT-rail distance.
T-ra_
• Raise the opener onto a stepladder.
2x4
I
You will need help at this point ff the ladder is
not tall enough.
• Open the door all the way and place a 2x4 laid flat
on the top section beneath the T-rail.
Door
ff the top panel hits the trolley when you raise
the door, pull down on the trolley release arm to
disconnect the Inner and outer sections. The
trolley can remain disconnected until Step 12 Is
completed.
ReleaseAnn
T_ley
Header
• With the door fully open and parallel to the floor,
measure the distance from the floor to the top of
the door.
• Using a stepladder as a support, raise the opener
to the same distance as the door from the floor (it
will be at a slight angle as shown).
• The top of the door should be level with the top of
the opener. Do not position the opener more than
2' above this point.
16
I
Installation Step 5
Hang the Opener
Two representative Installations are shown.
Yours may be different. Hanging brackets should
be angled, Figure 1, to provide dgid support. On
finished ceilings, Figure 2, attach a sturdy metal
bracket to structural supports before installing the
opener. The bracket and fastening hardware are not
provided. See accessory page 38.
Figure I
_
StructuraJ
• Measure the distance from each side of the opener
to the structural support.
• Cut both pieces of the hanging bracket to required
lengths.
5/16 -18xl -7/8"
• Drill 3/16" pilot holes in the structural supports.
Measure .__,
• Attach one end of each bracket to a support with
5/16"-18xl -7/8" lag screws.
• Fasten the opener to the hanging brackets with
5/16"-18x7/8" screws, lock washers and nuts.
• Check to make sure the T-rail is centered over the
door (or in line with the header bracket if the
bracket is not centered above the door).
5/16"-18x7/8"
Screw
5/16" Lock Washer
5/16".18 Nut
• Remove the 2x4. Operate the door manually. If the
door hits the rail, raise the header bracket.
Figure 2
Hidden . . o....°
SupDort
o,..-
Grease the top and underside of the
rail surface where the trolley
__,_
slides. A tube of grease is _-__
supplied.
.....
"" °
..-'_
"" _ ..;-;'.;;"'°"--_.0SH=OCSlU,G-- "".'.. - ° ""
SupportSra_dxet_
Not Provided)
_.\_,
5/I 6"-I 8X7/8" Scte_
Hardware Shown Actual Size
5/16"18xl-7/8"
11111111111111111,llD
5/16"- 18X7/8"
Nut 5/16"-18
LockWasher 5/16"
17
o-"" "'"
...;-:::Lag Screws •
5/16"-18X1-?/8
_
_'"
..°-:.°-
_
_
..-"
5/ (Not Prodded)
16"-18x7/8
_---_..-
Screw
Installation
Step 6
Install the Door Control
I
Do not connect to live electrical widng. Connect
only to 24 Volt low voltage wires. Connection to
live wires or higher voltage may cause serious
injury from shock, burn or electrocution.
Children operating or playing with a garage
door opener can injure themselves or others.
The garage door could close and cause
serious injury or death.
Locate the door control within sight of the door
at a minimum height of 5 feet where small
children cannot reach, and away from all moving
)arts of the door and door hardware.
The door control is typically attached directly to the
wail. If installing into drywall, drill 5/32" holes and
use the anchors provided. For pre-wired installations
(as in new home construction), Console models
may be mounted to a.standard single gang box
(Figure 2).
Install the door control (or any additional push
buttons) out of the reach of children and away
from all moving parts of the door and door
hardware, but where the garage door is visible.
Do not allow children to operate the push
button(s) or the remote control(s).
A moving garage door could injure someone
under it. Activate the opener only when the
door is properly adjusted, you can see It clearly,
and the.re are no obstructions to door travel.
1. Strip 1/4" of insulation from one end of the bell
wire and connect it to the two screw terminals on
the back of the door control: white to 2 and
white/red to 1.
2. Door Control Button: Fasten securely with
6ABx1-1/2" screws.
Console Model: Pry off cover along one side
with a screwdriver blade (Figure 1). Fasten with
6ABx1-1/4" self-tapping screws (standard
installation) or 6-32x1" machine screws (pre-wired
installation) as follows:
Hardware Shown
Actual Size
6AB x 1-1/2" Screw
DoorControlButton
• Install bottom screw, allowing 1/8" to protrude
above wall surface.
Contxo4Console(std instaltadon)
• Position bottom of door control on screw head
and slide down to secure. Adjust screw for snug
fit.
Staples
Control
Console
Lore-wired)
• Install top screw with care to avoid cracking
plastic housing. Do not overtighten.
Figure 1
• Insert top tabs and snap on cover.
REMOVE & REPLACECOVER
DryWa_Anchom
Figure
2
PRE-WIRED
INSTALLA'RON
3. (For standard insta/lation only) Run the bell wire
up the wall and across the ceiling to the opener.
Use insulated staples to secure the wire in
several places. Be careful not to pierce the wire
with a staple, creating a short.
4. Connect the bell wire to the terminal screws on
the opener panel: white to 2; white/red to 1.
24 Volt
2-Conducto¢
BellWire
5. Positionthe antenna wire as shown.
STANDARD CONTROL
(BACK
VIEW)
Top
T_nal
DOOR CONTROL
BUTTON (BACK)
PREMIUM
CONTROL
(BACKVIEW)
Top
Wire
Terminal Screws
DOOR
CONTROL
BuTroN
STANDARO
CONTROL
CONSOLE
PREMIUM
CONTROL
CONSOLE
BackPanel
orOpener
_
Te_Nnal
_1 ''_=_
>scfewt
Be..
W'ffm _.
18
[.__
.Mou_ng
HO_
,
6. Attach the User Safety Instruction label to the wall
neat the door control, and the Maintenance
Instruction label in a prominent location on the
inside of the garage door.
Do NOT connect the power and operate the
openerat this time. The trolley will travel to the
full open position but wilt not return to the
close position
until the sensor
beam is
connected and properly aligned.
See Safety Reversing
Sensor instructions
beginning on page 21.
Page 32 explains how to use the door control.
Installation
Install
the Light
Install
the light:
r
Step 7
and
the Lens
• Install a 75 watt maximum light bulb in each
socket. The lights will turn ON and remain lit for
approximately 4-1/2 minutes when power is
connected. Then the lights will turn OFF.
• If the bulbs bum out prematurely due to vibration,
replace them with standard neck "Garage Door
Opener =bulbs.
Install
the lens:
• Apply slight pressure on the sides of each lens
and slide the tabs into the slots in the side panels.
', For convenience, the lens may be Installed
after Adjustment Step 4 on page 30.
• Reverse the procedure to remove the lenses.
Installation
Step 8
Attach
the Emergency
Release
Rope and Handle
I
Do not use the
red handle to pull the door
open or closed. The rope knot could become
untied and you could fall. Use the emergency
release only to disengage the trolley and, if
possible, only when the door Is closed.
• Thread one end of the rope through the hole in
the top of the red handle so "NOTICE" reads dght
side-up a_shown. Secme with an overhand knot.
The knot should be at least 1" from the end of
the rope to prevent slipping.
Garage doors are heavy. _t the door is open
when the handle is pulled, the door could
close inadvertently
if it Is not properly
balanced. Serious Injury may result to persons
under the door. Make sure the doorway is clear
of persons and obstructions
before pulling
handle when door is open.
:• Thread the other end of the rope through the hole
in the release arm of the outer trolley.
• Adjust rope length so the handle is 6 feet above
the floor. Secure with an overhand knot.
r
If it is necessary to cut the rope, heat seal the
cut end with a ma_ch or lighter to prevent
unraveling.
P.ekmseAnn
Rem
19
Handle
Installation
Electrical
Step 9
Requirements
To prevent electrocution or fire, installation
and wiring must be In compliance with local
electrical and building codes.
Do NOT use an extension cord, 2-wire adapter,
or change the plug In any way to make it fit
your outleL
To reduce the risk of electric shock, your garage
door opener has a grounding type plug with a third
grounding pin. This plug will onlyfit into a grounding
type outlet.
If the plug doesn't fit into the outlet you have,
contact a qualified electrician to install the proper
outlet.
OQ
To avoid installation difficulties,
do not run the opener at this time.
Right
Wrong
If permanent wiring Is required by your local code, refer to the following procedure:
To prevent e/ecfrocut/on, remove power from
the garage door opener and from the circuit
Permanent
Wiring
Connections
To make a permanent connection through the
7/8" diameter hole in the top of the opener
(according to local code):
GroundTab
• Remove the opener cover screws and set the
cover aside.
Gresn
• Remove the attached 3-pmag cord.
S_ew
• Connect the black (line) wire to the screw on the
brass terminal; the white (neutral) wire to the
screw on the silver terminal; andthe ground wire
to the green ground screw. The opener must be
grounded.
• Reinstall the cover.
Back
Winl
Wire
Wh.e W_I
Wire
i,
To avoid installation difficulties,
do not run the opener at this time.
2O
The Safety Reversing
Information
you'll
need
before
you
begin
the installation
System
of the safety
reversing
sensor,
The safety reversing sensor must be connected
and aligned correctly before the garage door
opener will move In the down direction. This is a
required safety device and cannot be disabled.
Installation procedures are the same for sectional
and one-piece doors.
Read and follow all Instructions.
To protect small children, install the safety
reversing sensor so that the beam will be no
higher than 4"-6" above the garage floor.
Disconnect power to the garage door opener
before Installing the safety reversing sensor.
Be sure power to the opener is disconnected.
The brackets mustbe securely fastened to a solid
surlace such as the studs on either side of the door,
or add a piece of wood at each location if installing in
masonry construction.
The sending eye transmits an invisible light beam to
the receiving eye. The units can be Installed on
either slde-of the'garage door as long as the sun
never shines directly into the receiving eye lens.
Look at the label on the connector end of each case
to identify the sensors.
The invisible light beam path must be unobstructe(_l.
No part of the garage door (or door tracks, spdngs,
hinges, rollers or other hardware) can interrupt the
beam while the door is closing. If it does, use a piece
of wood to build out each sensor mounting location to
the minimum depth required for light beam clearance.
The brackets must be connected and fastened so
that the sending and receiving eyes face each other
as shown in Rgure 1.
If an obstruction breaks the light beam while the
garage door is closing, the door will stop and
reverse to full open position and the opener lights
will,flash for 5 seconds.
[
Sensor Beam
=bore n_x
Figure 1: Facing the door from inside the garage
21
I
Installation Step 10
Install
the Safety
Reversing
Sensor
Figure 2
' Figures 2 and 3 show assembly of brackets and
i "C" wrap based on the recommended installation of
the sensors as shown on page 21.
Mo_
Brac_l
W'dhSquareHoles
However, Figures 4 and 5 are vadetions which may
fit your installation requirements better. Make sure
the wraps end brackets are aligned so the
sensors will face each other across the garage
door,
#10-32
Lo<:kNuts
• Fasten the "C" wraps to the mounting brackets
having square holes, using the hardware shown
in Figure 2.
• Connect each assembly to a slotted bracket, using
the hardware shown in Figure 3.
Figure 3
Note the alignment of the brackets for left and
right aides of the door.
• Finger tighten the lock nuts.
• Use bracket mounting holes as a template to
locate and ddll (2) 3/16' diameter pilot holes on
both sides of the garage door, 4"-6" above the
floor but not exceeding 6: (See warning on
page 21.)
• Attach bracket assemblies with 1/4"x1-1/2" lag
screws as shown in Figure 3.
• Adjust dght and left side bracket assemblies to the
same distance out from the mounting surface.
Make sure all door hardware obstructions are
dealed. Tighten the nuts securely.
Hardware Shown Actual Size
©
©
#10 o _12x :_gS"
SOtew
Figure
#10x32
114"- 20 x 1i'Z'
LockNut
Lag_
St=paB
Figure 5
4
Alternate Wall Mount
Alternate Floor Mount
withSlot
--Floor--
_2
114"-20
LockNut
• Center each sensor unit in a "C" wrap with lenses
pointing toward each other across the door (see
Figure 6).
Figure 6
• Secure sensors with the hardware shown. Finger
tighten the wing nut on the receiving eye to allow
for final adjustment. Securely tighten the sending
eye wing nut.
114-20x 1-1/2°
FlexBoat
• Hun the wires from both sensors to the opener.
Use insulated staples to secure wire to wall and
ceiling.
Trouble Shooting
• Strip 1/4" of insulation from each set of wires.
Separate white and white/black wires sufficiently to
connect to the opener terminal screws: white to 2
and white/black to 3.
1. If the sending eye indicator light does not glow
steadily after installation, check for:.
• Electric power to the opener.
• A short in the white or white/black wires. These
can occur under staples or at screw terminal
connections.
Aligning the Safety Sensors
• Plug in the opener. Green indicator lights in both
the sending and receiving eyes will glow steadily if
wiring connections and alignment are correct.
• Incorrect wiring between sensors and opener.
• An open wire (wire break).
The sending eye indicator light will glow regardless
of alignment or obstruction. If the indicator light is
off dim or flickering in the receiving eye (and the
invisible light beam path is not obstructed),
alignment is required.
• Loosen the sending eye wing nut and re-adjust,
aiming directly at the receiving eye. Look in place.
2. If the sending eye indicator light glows steadily but
the receiving eye indicator light doesn't:
• Check alignment.
• Check for an open wire to the receiving eye.
3. If the receiving eye indicator light is dim, realign
either sensor.
NOTE: When the invisible beam path is obstructed or
miseligned while the door is closing, the door will
reverse. If the door is already open, it will not close.
The opener lights will flash 10 times. (If bulbs are not
installed, 10 clicks are audible.) See page 21.
• Loosen the receiving eye wing nut and adjust
sensor vertically and/or horizontally until it receives
the sender's beam. When the green indicator light
glows steadily, tighten the wing nut.
Hardware Shown Actual Slze
Figure 7
1/4-20 x 1-I/2"
HI,I
I,l,l,I;lii
I,%II,I,I,I,D
Bel Wire
__
ConnectWire to
OpenerTerminals
Rn_'md -Ceiling
BellWire
DoorControl
Sensor
Connectloes_
(dottedline)
.-.
Con_ections
[]
OPENER TERMINAL
Sensor
InvisibleLightBum
ProtectionArea
23
SCREWS
Installation
Step 11
Fasten Door Bracket
To prevent
damage
to steel, aluminum,
fiberglass
or glass panel doors, always
reinforce the inside of the door both vertically
and horizontally with an angle iron.
Follow instructions which apply to your door
type as illustrated below or on page 25.
A horizontal brace should be long enough to be secured to 2 vertical supports. A vertical brace should
cover the height of the top panel.
The illustration shows one piece of angle iron as the horizontal brace. For the vertical brace, 2 pieces of
angle iron are used to create a "U"-shaped support. The best solution is to check with your garage door
manufacturer for an opener installation door reinforcement kit.
I I!
_-_---tTIJ"___.etc)-_,Pr°_)
t-igure 1
r
""----
Carriage Bolt.
II\H
UP
=*
_.=deEd_
Figure 2
of Door ot
Reinforcement Board
!i_ .P.-i=_
• Center the door bracket on the previously marked
vertical guideline used for the header bracket
installation. Note the correct UP placement, as
stamped inside the bracket.
Door Bracket
• Position the bracket on the face of the door within
the following limits:
Hardware Shown Actual Size
©
A) The top edge of the bracket 2'-4" below the top
edge of the door.
S) The top edge of the bracket directly below any
structural support across the top of the door.
Nut 5/16--18
• Mark and ddll 5/16" left and right fastening holes.
Secure the bracket as shown in Figure I if there is
vertical reinforcement.
l.ockWasher 5/16"
IIIIIIIIIIIII11
IIIllll111111111
If your installation doesn't require vertical reinforcement but does need top and bottom fastening holes
for the door bracket, fasten as shown in Figure 2.
5/16--18
24
x 2-1/2"
Please read and comply with the warnings and reinforcement instructions on page 24.
They apply to one-piece doors also.
• Center the bracket on the top of the door, in line
with the header bracket as shown. Mark holes
Hardware Shown Actual Size
• Ddl! 5/16" pilot holes and fasten the door bracket
with hardware supplied,
©
If the door has no exposed framing, drill 3/16" pilot
holes and fasten the bracket with 5/16=x1-I/2" lag
screws (not provided) to the top of the door.
The door bracket may be installed on the top
edge of the door if required for your installation.
(Refer to the dotted line optional placement
drawing.) Drill 3/16" pilot holes and substitute
5/16"x1-1/2" lag screws (not provided) to fasten
the bracket to the door.
I_.< _16"-18
LockWashe_ 5/_6"
5/1_'-1_t X 2-1/2 =
k
25
Installation
Connect
Step 12
Door Arm to Trolley
Follow Instructions which apply to your door
type as illustrated below and on page 27.
Make sure garage door is fully closed. Pull the emergency release handle to disconnect the outer trolley
from the inner trolley. Slide the outer trolley back (away from the door) about 2" as shown in
Figures 1, 2 and 3.
Figure 1:
Figure 2:
Fasten straight door arm section to outer trolley
with the 5/16"x1" clevis pin. Secure the connection
with a ring fastener.
Fasten curved door arm to the door bracket in the
same way, using the 5/16 "x I - 1/4" clevis pin.
• Bring arm sections together. Find two pairs of holes
that line up and join sections. Select holes as far
apart as possible to increase door arm rigidity.
Inner Trolley
5/16"x1"
Ring
Fastener
/
/
0
Ooor
',
BPac_et
Do_ Am1
"_
5/16"x1-1/4"
v
Door Arm
Figure I
ooo,
e._t
S116"-18xTi8"
Figure 2
Hole Alignment Alternative
Figure 3:
• If holes in curved arm are above holes in straight
arm, disconnect straight arm. Cut about 6" from
the solid end. Reconnect to trolley with cut end
down as shown.
Bring arm sections togeg_er.
Find two pairs of holes that line up and join with
screws, lock washers and nuts.
•
5/16"
Hardware Shown Actual Size
Nut 5/16" - 18
Lock Washer
_Pg'l
sit6"x 1"(Tfot_ey)
5/16"
C_Nn
5/16"x1-114" (Door B_lcket)
Figure 3
r
He_ Screw
5/16"- 18 x 7/_"
Proceed to Adjustment Step 1, page 28. Trolley will re-engage automatically when the opener is operated.
26
Assemblethe DoorArm:
• Fasten the straight and curved door arm sections
together to the longest possible length (with a 2 or
3 hole ovedap).
PJ_
ooor
• With the door closed, connect the straight door arm
section to the door bracket with the 5/16"xl -1/4"
clevis pin.
cle_sF_n
_ls'xl.t/4"
SctN
5/16"-18X7/8
• Secure with a ring fastener.
On one-piece doors, before connectingthe door arm to _ trolleythe travel limits must be adjusted. Limit adjustment
screws are located on the left side panel as shown on page 28. Follow adjustment procedure s below.
FuUy
Closed
Trolley
..........
.......
.....
.._
_,.,A'
•-_ o o °
.
_
Conne_of
Hole
Do(x Ann
................
.:22222
JJ I
....... t
.....--'°l......
I
Adjustment Procedures for One-Piece Doors
Open Door Adjustment:
Decrease UP limit
Closed Door Adjustment:
Decrease DOWN limit
• Turn the UP limit adjustment screw counterclockwise 5-1/2 turns.
• Turn the DOWN limit adjustment screw clockwise 5
complete turns.
• Press the Door Control push bar or button. The
trolley will travel to the fully open position.
• Press the Door Control push bar or button. The
trolley will travel to the fully closed position.
• Manually raise the door to the open position
(parallel to the floor), and lift the door arm to the
trolley. The arm should touch the trolley just in
back of the door arm connector hole. Refer to the
fully open trolley/door arm positions in the
illustration. If the arm does not extend far enough,
adjust the limit further. One full tum equals 2" of
trolley travel.
• Manually close the door and lift the door arm to the
trolley. The arm should touch the trolley just ahead
of the door arm connector hole. Refer to the fully
closed trolley/door arm positions in the illustration. If
the arm is behind the connector hole, adjust the limit
further. One full turn equals 2" of trolley travel.
Connect the door arm to the trolley,
• Close the door and join the curved arm to the connector hole in the trolley with the remaining clevis pin. It may
be necessary to lift the door slightly to make the connection.
• Secure with a dng fastener.
• Run the opener through a complete travel cycle. If the door has a slight "backward" slant in full open position
as shown in the illustration, decrease the UP limit until the door is parallel to the floor.
27
Adjustment
Adjustment
Adjust
Section:
Pages 28 - 30
Step 1
the UP and DOWN
Limits
Do not make any limit adjustments until the
safety reversing sensors are completely
installed.
Limit adjustment settings regulate the points at
which the door wilt stopwhen moving up or down.
The door will stop i6the up direction if anything
interferes with door travel. The door will reverse in
the down direction if anything interferes with the
door travel (including binding or unbalanced doors).
To operate the opener, press the Door Control push
button. Run the opener through a complete tra,_el
cycle.
Umit
Adju=lr_.mt
Screws
• Does the door open and close completely?
Does the door stay closed and not reverse
unintentionally when fully closed?
f your door passes both of these tests, no limit
adjustments are necessary unless the reversing test
fails (See page 30).
Cover /
Protection
Bo_t
LeftSidePanel
Adjustment procedures are outlined below. Run the
opener through a complete travel cycle after
each adjustment.
Repeated operation of the opener during adjustment
)rocedures may cause the motor to overheat and
shut off. Simp/y wait 15 minutes and try again.
Adjustment Label
Read the procedures carefully before continuing on
to Adjustment Step 2. Use a screwdriver to make
limit adjustments.
How and When to Adjust the Limits
If you have adjusted the door arm to the maximum
length and the door still will not close completely,
lower the header bracket. See Installation Step 1,
pages 12 and 13.
• If the door does not open completely
but opens at least five feet:
Increase up travel. Turn the UP limit adjustment
screw clockwise. One turn equals 2" of travel.
• If the opener reverses In fully closed position:
NOTE: To prevent the trolley from hitting the
cover protection bolt, keep a minimum distance
of 2-4" between the trolley and the bolt.
Decrease down travel. Turn the DOWN limit
adjustment screw clockwise. One turn equals 2" of
travel.
• If door does not open at least 5 feet:
• If the door reverses when closing and
there is no visible Interference to travel cycle:
Adjust the UP (open) force as explained in
Adjustment Step 2.
If the opener lights are flashing, the Safety Reversing
Sensors are either not installed, misaligned, or
obstructed. See Troubleshooting, page 23.
• If the door does not close completely:
Increase down travel. Turn the DOWN limit
adjustment screw counterclockwise. One turn
equals 2" of travel.
Test the door for binding: Pull the emergency release
handle. Manually open and close the door. If the door
is binding, call for garage door service. If the door is
not binding or unbalanced, adjust the DOWN (close)
force. See Adjustment Step 2.
If door still won't close completely and the trolley
bumps into the pulley bracket (see page 4 or 5), try
lengthening the door arm. (see page 26).
28
Adjustment
Adjust
Step 2
WARNING
the Force
I
Too much force on the door will interfere with
the proper operation
of the safety reverse
system. The door might not reverse properly
when required and could seriously injure or kill
someone under iL Do not increase the force
beyond the minimum amount required to close
the door. Do not use the force adjustments to
compensate for a binding or sticking garage
door. Test the safety reverse system following
all adjustments to force levels. See page 30.
Force adjustment controls are located on the back
_anel of the opener. Force adjustment settings
regulate the amount of power required to open and
close the door.
The door will stop in the up direction if anything
interferes with its travel The door will reverse in the
down direction if anything interferes with its travel
(including binding or unbalanced doors).
If the forces are set too light, door travel may be
interrupted by nuisance reversals in the down
direction and stops in the up direction. Weather
conditions can affect the door movement, so
occasional adjustment may be needed.
Backpanel of
dooropener "
Force
\
Ad|uslmlmt
The maximum force adjustment range is 260 degrees,
about 3/4 of a complete turn. Do not force controls
beyond that point. Turn force adjustment controls
with a screwdriver.
AdjusUnentLabel
How and When to Adjust the Forces
Test the DOWN (close) force
Make 10 degree turn adjustments until the door stops
easily. After each adjustment, run the opener through
a complete travel cycle.
Grasp the door bottom when the door is about
halfway through DOWN (close) travel. The door
should reverse. Reversal halfway through down
travel does not guarantee reversal on a one-inch
obstruction. See page 30. If the door is hard to
hold or doesn't reverse, decrease the DOWN (close)
force by turning the control counterclockwise.
If the door doesn't open at least 5 feet
Increase UP (Open) force by turning the control
clockwise. Make 10 degree turn adjustments until
door opens completely. Re-adjust the UP limit if
necessary. After each adjustment, run the opener
through a complete travel cycle.
Make 10 degree turn adjustments until the door
reverses normally. After each adjustment, run the
opener through a complete cycle.
If the door reverses during the down (close) cycle
and the opener lights aren't flashing
Test the UP (open) force
Increase DOWN (close) force by turning the control
clockwise. Make 10 degree turn adjustments until the
door completes a close cycle. After each adjustment,
run the opener through a complete travel cycle. Do
not increase the force beyond the minimum
amount required to close the door.
Grasp the door bottom when the door is about
halfway through UP (open) travel. The door should
stop. If the door is hard to hold or doesn't stop,
decrease UP (open) force by tuming the control
counterclockwise.
29
Adjustment
Step 3
Test The Safety
Reversing
Sensor
I
• Press the remote control push button to open the
door.
• Place the opener carton in the path of the door.
• Press the remote control push button to close the
door. The door will not move more than an inch,
and the opener light will flash.
Professional serv.lce is required if the opener
closes the door when the safety reversing
sensor is obstructed.
The garage door opener will not close from a
remote control if the Indicator light In either
sensor is off(alerting you to the fact that the
sensor is mlseligned or obstructed).
The garage door can be dosed by pressing and
holding the Door Control push button until down
travel is completed.
Adjustment
Test the Safety
Step 4
Reverse
System
I
Test:
• Place a one-inch board (or a 2x4 laid flat) on the
floor, centered under the garage door.
• Operate the door in the down direction. The door
must reverse on striking the obstruction.
L_
Adjustment:
If the door stops on the obstruction, it is not traveling
far enough in the down direction.
• Increase the DOWN limit by turning the DOWN
limit adjustment screw counterclockwise 1/4 turn.
• Repeat the test.
-
On a sectional door, make sure limit adjustments
do not force the door arm beyond a straight up
and down position. See the illustration on page 26.
• When the door reverses on the one-inch board,
remove the obstruction and run the opener through
3 or 4 complete travel cycles to test adjustment.
If the door will not reverse after repeated
adjustment attempts, call Sears Service Center
for garage door opener service.
Important safety check
Repeat Adjustment Steps 1, 2 and 4 after:
• Each adjustment of door arm length, force controls
or limit controls.
• Any repair to or adjustment of the garage door
(including springs and hardware).
• Any repair to or buckling of the garage floor.
• Any repair to or adjustment of the opener.
3O
IMPORTANT
'
':-,
SAFETY
;,.i
INSTRUCTIONS
!
f..
To reduce the risk of severe injury
1. READ AND FOLLOW ALL INSTRUCTIONS.
WARNING
,
,
,
,
,
i
i
or death to persons:
5. If possible, use the emergency release only
when the deer is in a closed position. Caution
should be taken whenever the disconnect cord
is actuated with the door open. Weak or broken
springs may cause the door to fall rapidly,
causing injury or death to persons.
6. KEEP GARAGE DOORS PROPERLY
BALANCED. See page 3. An improperly
balanced door may not reverse when required
and could result in severe injury or death.
Repairs to cables, spring assemblies and other
hardware must be made by a professional
garage door person.
2. Do not permit children either to operate or to
play with the opener. Keep remote control In a
location inaccessible to children.
3. Operate opener only when the door is in full
view and free from any obstruction. Keep the
door in sight until it is completely closed. NO
ONE SHOULD CROSS THE PATH OF THE
MOVING DOOR.
4. Check safety reversal system monthly. See
page 30. The garage door MUST reverse on
contact with a one-inch (or a 2x4 board I.ald
flat) object placed on the floor. If an adjustment
is made to either the force or the limit of travel,
both adjustments may be needed and the
safety reversal system must be checked.
Failure to properly adjust the opener may
result in severe injury or death.
7. Disconnect the electric power to the garage
door opener before making any repairs or
removing the covers.
s.SAVE THESE INSTRUCTIONS.
Care of Your Opener
Limit and force adjustment
controls
The remote control
3-FUNCTION
Open thls end
Limit Controls
Force Controls
AdjustmentLabel
(Located on the le/t side panel]
AdJu_at_mtLabe/
(Locatedon the rightside panel)
The lithium batteries should
produce power for up to
5 years. To replace batteries,
use the visor clip or screwdriver
blade to pry open the case, as
Twist hem
shown. (UOpen"location is
COMPAC
to oden
stamped on back of remote
control case.) Insert batteries positive side down.
Weather conditions may cause some minor
changes In door operation requiring some readjustments, particularly during the first year of
operation.
Replace cover as follows. 3-Function remote: insert
the 3 tabs at the opposite end and snap shut. Compact
3-Function remote: Snap shut along both sides.
Dispose of old batteries properly.
Pages 28 and 29 refer to the limit and force
adjustments. Only a screwdriver is required. Follow
the instructions carefully.
Repeat the safety reverse test (page 30) after any
adjustment of limits or force.
Maintenance Schedule
Once a Month
Twice a Year
Manually operate door. if it is unbalanced or
binding, call for professional garage door service.
Check chain tension. Disconnect trolley first.
Adjust if necessary (See page 11).
Once a Year
Check to be sure door opens & closes fully.
Adjust limits and/or force it necessary.
(See pages 28 and 29.)
Oil door rollers, bearings and hinges. The opener
does not require additional lubrication. Do not
grease the door tracks.
Repeat the safety reverse test. Make any
necessary adjustments (See page 30).
31
Operation
of Your Opener
Activate the opener with any of the following:
• The Remote Control: Hold push button down until
the door starts to move.
• The Door Control: Hold push button down until the
door starts to move.
Weak or broken springs could allow an open
door to fall (either rapidly or unexpectedly),
resulting in serious injury, death or property
damage. If possible,
use the emergency
release rope and handle only when the door is
fully closed.
• The Outdoor Key Switch or Keyless Entry.
(See Accessories)
When the opener is activated with the safety
reversing sensor installed and correcUy aligned:
1. If open, the door will close. If closed, the door will
open.
2. If closing, the door will reverse.
3. If opening, the door will stop (allowing space for
entry and exit of pets and for fresh air).
4. If the door has been stopped in a partially open
position, it will close.
5. If obstructed while closing, the door will reverse.
Emergency
6. if obstructed while opening, the door will stop.
Release Handle
(Pull Down)
7. The garage door will reverse in the closingcycle when
the invisible beam is broken, if fullyopen, the door will
not close when the beam is broken. The sensor has
no effect in the opening cycle.
Manual disconnect
position
The lockout feature
prevents the trolley
from reconnecting
automatically. Pull the
emergency handle
down and back (toward
the opener). The door
can then be raised and
lowered manually as
often as necessary. To
disengage the lookout
feature, pull the
emergency handle
straight down. The
trolley will reconnect on
the next UP or DOWN
operation.
If the sensor is not installed or not aligned correctly,
the door won't close from any remote control. You can
close the door with the Door Control, the Outdoor Key
Switch, or Keyless Entry, however, if you activate
them until down travel is complete. If you release them
too soon, the door will reverse.
The opener lights will blink for 5 seconds when the
safety reversing sensor causes the door to reverse.
The Opener Lights will turn on under the following
conditions: When the opener is initially plugged in; when
the power is interrupted; when the opener is activated.
They will turn off automatically after 4-1/2 minutes or
provide constant light when the Light feature on the
Premium Control Console is activated. SECURITY,I,
models: Lights will also turn on when someone walks
through the open garage door. Bulb size is 75 watts
maximum.
To open the door
manually:
The door should be
fully closed if possible.
Pull down on the red
emergency release
handle and lift the door
manually. To
reconnect the door to
the opener, press the
Door Control push
button.
O_
.
Trolley
Release Arm
Emergency
Release Handle
(Pull Doom& Back
Towards Opener)
Lockout position
Operation
of the Door Controls
(see page 18)
(SECURITY.I, models: See additional programming features, next page.)
Press the lighted push button to open or close the
door.
Premium Console (cont.):
Lock feature: The Lock feature is designed to
prevent operation of the door from remote controls.
However, the door will open and close from the
Door Control, the Outdoor Key Switch and the
Keyless Entry Accessories.
To activate: Press and hold the small round Lock
button for 2 seconds. The push button light will
flash as long as the Lock feature is on.
Press again to reverse the door during the closing
cycle or to stop the door while it's opening.
Premium Console:
Light feature: Press the large round Light button, if
the opener light is off, it will tum on. If the opener
light is on, (even in the 4-1/2 minute automatic
cycle) it will turn off.
To turn off: Press and hold the Lock button again
for 2 seconds.The push button light will stop
flashing. The Lock feature will also turn off
whenever the SRT button on the opener panel is
activated.
But if you use the Light button to turn the lights on
and then activate the opener, the lights will turn off
after 4-1/2 minutes.
The Light button will not control the opener lights
when the door is in motion.
32
Receiver and Remote Control Programming
To comply with FCO roles, adjustment or modifications of _s receiver and/or
I_ilter
are ptohlbited, except for changing the code setling or ,_placing
Ihe battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
SECURITY
Your garage door opener receiver and remote control
have been pre-set at the factory. The door will open
when you press the LARGE remote control push
button. The code between the remote control and the
receiver changes with each use, randomly accessing
over 100 billion new codes.
Children operating or playing with a garage
door opener can injure themselves or others.
The garage door could close and cause serious
injury or death. Do not allow children to operate
the door push button(s) or remote control(s).
The 3-function remote control can also activate
additional SECURITY+ garage door openers and/or
light controls.
Your SECURITY+
A moving garage door could injure or kill
someone under it. Activate the opener only
when you can sea the door clearly, it is free of
obstructions, and is properly adjusted.
opener will operate with:
• several SECURITY+ remote controls (with blue
push buttons) utilizing up to 8 functions.
• one SECURITY+ Keyless Entry System
(Model 139.53684).
Follow the instmctionsbelow to program your opener
to match any additional remotes you may purchase.
See Accessories on page 38.
Rgure I
Select = remotecontrolpush
buttonto o_emlo opener
To Add A Remote Control
Figure
If you have a Premium Control Console:
1. With the door closed, press and hold a remote
control push button. See Figure 1.
SECURITY,I,
Garage Door Opener
SECURITY'I"
2. Press and hold the Light button on the door
control.
2
Remote Control
3. Press and hold the door control push button.
3-Function
4. After the opener light flashes, release all buttons.
Test by pressing the remote push button.
.,._O0000tl_
•
SRT(leam)
Button
Indicator
BACK
Ught
PANEL
ff you do not have a Premium Control Console:
1. Press and holdthe selected remote control push
button. See Figure 1.
IISO tocatod
2.Then press and release the SRT (leam) button on
the back panel of the opener, Figure 2. The
indicator light on the panel will begin to blink and
the opener light will flash once.
OIt the opllner _
To Control the Opener Light (Premium Consoles)
With SECURITY.Ik remote controls, a push button can
be programmed to operate the opener light without
opening the door.
1. With the door closed, press and hold the remote
button that you want to control the light.
3. Release the remote push button.
Test by pressing the remote push button.
To Erase All Remote Control Codes
2. Press and hold the Light button on the door
control.
Press and hold the SRT button on the opener panel
until the indicator light turns off (about 6 seconds). All
remote control codes are now erased. Then follow
the steps above to re-program each remote control.
3. Press and hold the Lock button on the door control.
4. After the opener light flashes, release all buttons.
Test by pressing the remote push button. The opener
light should turn on or off but the door should not move.
33
Having a Problem?
Situation
Probable
Cause and Solution
The opener doesn't
operate from either
the Door Control or
the remote control:
1. Does the opener have electric power?. Plug a lamp into the outlet, ff it doesn't light,
check the fuse box or the cimuit breaker. (Some outlets are controlled by a wail switch.)
2. Have you disabled all door locks? Review installation instructionwamings on Page 11.
3. Is there a build-up of ice or snow under the door?.The door may be frozen to the
ground. Remove any restriction.
4. The garage door spring may be broken. Have it replaced.
5. Repeated operation may have tripped the overload protector in the motor. Wait
15 minutes. Try again.
Opener operates
from the remote
control, but not from
the Door Control:
1. Is the Door Control lit? If not, remove the bell wire from the opener terminal screws.
Short the red and white terminals by touching both terminals at the same time with a
piece of wire. If the opener runs, check for a faulty wire connection at the Door
Control, a short under the staples, or a broken wire.
2. Are the wiring connections correct? Review Step 6, page 18.
The door operates
from the Door
Control, but not from
the remote control:
1. Is any door push button flashing? If your model has the Lock feature, make sure the
lock is Off.
2. Your opener needs to re-learn a remote control code. Refer to instructions on the
opener panel.
3. Program the receiver to match the remote control code.
4. Repeat the receiver programming procedure with all remote controls.
The remote control
has short range:
1. Change the location of the remote control in your car.
2. Check to be sure the antenna on the side or back panel of opener extends fully
downward.
3. Some installations may have shorter range due to a metal door, foil backed
insulation, or metal garage siding. (Antenna Extender Kit 41A3504)
Opener noise Is
disturbing in living
quarters of home:
If operational noise is a problem because of proximity of the opener to the living
quarters, the Vibration Isolator Kit 41A3263 can be installed. This kit was designed to
minimize vibration to the house and is easy to install
The garage door
opens and closes
by Itself:
1. Be sure that all remote control push buttons are off.
2. Remove the bell wire from the Door Control terminals and operate from the remote
control only. If this solves the problem, the Door Control is faulty (replace), or there is
an intermittent short on the wire between the Door Control and the opener.
3. Clear memory and reprogram all remote controls.
The door doesn't
open completely:
1. Is something obstructing the door?. Remove the obstruction or repair the door.
2. If the door has been working propedy but now doesn't open all the way, increase the
up force. See page 29.
3. If door opens at least 5 feet, the travel limits may need to be increased. One turn
equals 2 inches of travel. See page 28.
Repeat the safely reverse test after the adjustment is complete.
The door stops but
doesn't close
completely:
Review the travel limits adjustment procedures on page 28.
Repeat the safely reverse test after any adjustment
force or down IimlL
34
of door arm length, close
Having a Problem?
(continued)
Situation
Probable
The door opens but
won't close:
1.
If the opener lights blink, check the safety reversing sensor. See page 23.
2. If the opener lights do not blink and it is a new installation, check the down force.
See Adjustmenr Step 2, page 29. For an existing installation, see below.
Cause & Solution
Repeat the safety reverse test after the adjustment is complete.
The door reverses for
no apparent reason
and opener lights
don _ blink:
The door reverses for
no apparent reason
and opener lights
blink for 5 seconds
after reversing:
The opener light:
Is something obstructing the door? Pull the red emergency release handle. Operate
the door manually. If it is unbalanced or binding, call for professional garage door
service.
1.
Clear any ice or snow from the garage floor area where the door closes.
3. Review the force adjustment procedures on page 29.
4. If door reverses in the fully closed position, decrease the travel limits (page 28).
Repeat safety reverse test after adjustments to force or travel limits. The need
for occasional adjustment of the force and limit settings is normal Weather
conditions in particular can affect door travel.
.
Check the safety reversing sensor. Remove any obstruction or align the receiving eye.
See page 23.
...
doesn,t turn on:
Replace the light bulbs (75 watts maximum). Use a standard neck garage door opener
bulb if regular bulb bums out.
•..
doesn_ turn off:
Is the Light feature on? Turn it off.
The opener strains or
maximum force is
needed to operate
door:
The door may be out of balance or the springsare broken. Close the door and use the
emergency release to disconnectthe trolley. Open and close the door manually. A properly
balanced door will stay in any point of travel while being supported entirely by its springs. If it
does not, disconnect the opener and call a professional garage door serviceman. Do not
increase the force to operate the opener.
The opener motor
hums briefly, then
won't work:
1. The garage door springs are broken. See above.
2. If the problem occurs on the first operation of the opener, door may be locked. Disable
the doorlock. If the chain was removed and reinstalled,the motor may be out of phase.
Remove the chain; cycle the motor to the down position.Observe the drive sprocket.
When itturns in a clockwisedirection and stops in the down position, reinstall the chain.
Repeat the safety reverse test after the adjustment is complete.
The opener won't
operate due to
power failure:
1. Use the emergency release to disconnect the trolley.The door can be opened and dosed
manually.When the power is restored, pr_ the Door Controlpush button and trolleywill
automaticallyreconnect(unlesstrolley is in lockoutpes_on.)See page 32.
2. The Emergency Key Release accessory (for use on garages with no service door)
disconnects the trolley from outside the garage in case of power failure.
The chain droops
or sags:
It is normal for the chain to droop slightly in the closed doer position. Use the
emergency release to disconnect the trolley. If the chain returns to normal height when
the trolley is disengaged and the door reverses on a one-inch board, no adjustments
are needed (see page I t).
35
Repair Parts
Rail Assembly
Parts
KEY
NO.
Installation Parts
PART
NO.
DESCRIPTION
1
1A995
Master link kit
2
3
41A3489
1B3117
Complete trolley assembly
T-rail - center section
4
5
6
183Bt 10
83A4
41A3473
T-rail - end section (each)
Rail grease
Chain and cabts
7
41 B2616
Cable pulley bracket assembly
NOT SHOWN
41A3534
Rail assembly hardware kit
(see page 7),
FORREMOTEM00EL
139._I
2
KEY PART
NO. NO.
1
2
3
4
5A
5B
6
7
8
9
10
11
12
13
14
41A4166
41A4884
41A4899
41A5032
10A19
10A20
29S134
41A2828
41A4353
217A238
178B35
31D431
10A2
31B430
41A4373A
15
16
17
18
19
20
41 A5047
12B483
12B484
12B485
12B350
178B34
41A3475-4
41A4116
114A2099
DESCRIPTION
Door controlbutton
Premiumcontrolconsole
Standardcontrolconsole
Remote control housing(no circuitbd.)
3V 2016 Lithiumbattery (2 required)
3V 2032 Lithiumbattery (1 required)
Visor clipfor Part No.41A5032
Emergencyrope& handleassy.
Header bracketw/clevispin & fastener
2-conductorbellwire - white & white]red
Curved door arm section
Keylsesentry keypadcover
12Volt battery
Keylessentry batterycover
SafetysensorIdt(receivingand sendingeyes)
with 3' 2-conductorball wire attached
Door bracketw/clevispin & fastener
"C"wrap bracket
Square hole bracket
Slottedbracket
Hanging brackets
Straightdoor arm section
NOT SHOWN
Installationhardwarebag (see page 7).
Safety sensorhardware
Owner'smanual
I
36
14
17
Repair Parts
Opener
Assembly
Parts
I
,ok1
""_
,'_
-G, 1"
"---.-. _i_i_,,--
_
18
17
116
'"--..
"--...6_
3 .' .. [
yS'_e'--_];i_'_:_13
"
LIMITSWITCH
__
"_ G_
Centre" Lim_
(Up)
CoaU_
Co_a_
KEY PART
NO. NO.
1
2
31D380
41C4220A
3
41A2817
4
5
6
7
8
41 B4245
41A4352
175B88
108D48-2
30B363
30B387
12A373
41A3150
9
10
_
yellow
wh
KEY PART
NO, NO.
DESCRIPTION
11
Sprocket cover
Gear and sprocket assy.
Complete with:
Spring washer
Thrust washer
Retaining ring
Bearing plate
Roll pins (2)
Drive gear and worm gear
Helical gear w/retainer and
grease
Drive/worm gear kit w/grease
Roll pins (2)
Une cord
End panel
Ught socket
Lens
Capacitor- 1/2 h.p.
Capacitor- 113 h.p
Capacitor bracket
Terminal block w/screws
12
13
14
15
16
17
18
19
20
37
41 D3058
DESCRIPTION
Universalreplacement motor and
bracketassembly
Complete with: Motor,worm,
bracket, bearing assembly, RPM
sensor
41D0328-6
Cover- 1/3 h.p.
41130328-7 Cover- 1/2 h.p.
41A2818
Helical gear and retainer w/grease
41 D3452
Limitswitch assembly
41C4398A
RPM sensor assembly
41C4246
Wire harness assy. w/plug
41A2826
Shaft bearing kit
41A2822A
Interruptercup assy.
41A5021-3B Receiver logic board assy.
Complete with:
Logic board
End panel w/all labels
41A3691
End panel w/all labels
NOT SHOWN
41A2825
Opener assembly hardware kit
(includesscrews not designatedby a
numberin illus.)
Accessories
Sears offers many useful accessories for your garage door opener. They are illustrated
Sears model numbers and descriptions.
139.53681
Emergency Key Release:
SECURITY.Ik 3-FuncUon Remote
Control:
Required for a garage with NO
access door. Enables homeowner
to open garage door manually from
outside by disengaging trolley.
Includes visor clip.
139.53680
139.53703
SECURITY+ Compact
3-Function Remote Control:
Outdoor Key Switch:
Operates the garage door
automatically from outside when
i remote control is not handy.
With loop for attaching key ring.
(Available April, 1997)
139.53684
139.53704
•
I
10 Foot Rail Extension:
Support Brackets:
Keylees Entry:
Enables homeownerto operate garage
door opener from outside by entering a
password.Also can add a temporary
passwordfor visitorsor service
persons.This temporary passwordcan
be limitedto a programmable number
of hours or entries.
139.53686
Plug-In Light Control:
Enables homeowner to turn on a
lamp, television or other appliance
from car, bedside, or anywhere in
the home with a remote.
139.53709
Door Clearance Brackets:
To allowa 10 footdoor to opan fu_.
53589
SECURITY+
8 Foot Rail Extension
To allowan 8 footdoor to openfu_
139.53705
below with
(For Sectional Doors Only)
For finished ceilings or where
additional support is required,
based on garage construction.
Includes brackets and fastening
hardware.
Replaces top brackets and rollers on
door to reduce height of door travel.
For use when installing opener in
garage with low headroom clearance.
To Add the Keyless Entry
We recommend that you program your password
before you install the Keyless Entry. You will not
need assistance, and you can test the reception at
the mounting location before installation.
If you do not have a Premium Control Console:
If you have a Premium Control Console:
2. Press the four buttons for the password, then press
and hold the Enter button. The indicator light on
the door opener panel will blink.
1. With the door closed, press the four digit password
desired, then press and hold Enter.
2. Press and hold the light button on the door control.
3. Press and hold the door control pushbar.
4. After the opener light flashes, release all buttons.
1. Choose a 4-digit password using numbers from
0 to 9 (a number can be used more than once, for
example, 4, 0, 4, 1).
3. Press and release the SRT (learn) button on the
opener panel. After the opener light flashes,
release the Enter button.
Test by pressing the password, then press Enter. The
door should begin to move.
Index
Access Door/Outside
Key Release Accessory ...............................................................................................
4, 5
Chain Tension ..............................................................................................................................................
4, 5, 11
Electrical Safety Warnings ........................................................................................................................
2, 20, 31
Garage Door
Testing for balance, binding and sticking...................................................................................................
Determining high point of travel:
Sectional door ...................................................................................................................................................
One-piece door .................................................................................................................................................
Disabling existing locks ....................................................................................................................................
Door clearance brackets (for garages with low headroom) ...........................................................................
Force controls
Adjustment procedures .................................................................................................................................
Problems that might require force adjustments .............................. :...........................................................
3, 28, 31
12
13
3, 11
12, 38
4, 29
34, 35
Safety warnings ..........................................................................................................................................
29, 31
Door hardware ...................................................................................
;................................. 3, 9, 11, 12, 18, 31, 32
Maintenance instruction label ........................................................................................................................
11, 28
Reinforcement requirements ...........................................................................................................................
4, 24
Removing of all ropes .......................................................................................................................................
3, 11
Possible door damage ...................................................................................................................................
16. 24
Travel limits
Adjustment procedures .....................................................................................................................................
Problems that might require limit adjustments ..........................................................................................
Safety warnings ..........................................................................................................................................
28
-34, 35
28, 31
Manual (Emergency) Release Rope & Handle
Lockout feature ....................................................................................................................................................
32
Manual disconnect ...............................................................................................................................................
32
Safety wamings .................................................................................................................................
11, 19, 31, 32
Opener Termlnals
Door control connections .....................................................................................................................................
Safety reversing sensor connections ...................................................................................................................
18
23
Operational Noise
Sprocket noise .....................................................................................................................................................
Vibration noise (isolator kit) .................................................................................................................................
11
34
Receiver and Remote Control
Programming the receiver ...................................................................................................................................
Erasing all codes .................................................................................................................................................
Activating other openers ......................................................................................................................................
Safety warning .....................................................................................................................................................
Problems with remote control operation ..............................................................................................................
33
33
33
33
34
Safety Reverse Test Procedure ..........................................................................................................................
30
Testing required .................................................................................................................................
11, 30, 34, 35
Safety reverse system problems
Securing header bracket to wall .......................................................................................................................
12
Adjusting travel limits ..............................................................................................................
_........................ .28
Applying excessive force on the door ...............................................................................................................
29
Buckling or uneven floor ............................................. :...................................................................................
4, 5
Safety Warnings .........................................................
2, 3, 9, 11, 12, 16, 18, 19, 20, 21,24,
28, 29, 30, 31, 32, 33
User Instruction Label for garage wall ........................................................................................................
39
11, 18
For professional
installation
Call 24 hours a day, 7 days a week
1-800-865-6500
For the repair
or replacement
parts you need
Call 7 am - 7 pm, 7 days a week
t -800-366-PART
(1-800-366-7278)
For in-home major brand repair service
Call 24 hours a day, 7 days a week
t -8OO-4-REPAIR
(1-800473-7247)
For the location
of a Sears
Repair
Service
Center
in your
area
Call 24 hours a day, 7 days a week
1-8OO-488-1222
For Information on purchasing a Sears Maintenance Agreement
about an existing Agreement
Call 9 am - 5 pm, Monday-Saturday
or to inquire
1-800-827-6655
The model number label is located under the light lens on the front end
panel of your opener. When requesting service or ordering parts, always
give the following information:
• Part Number
• Product Type
• Model Number
To obtain
this Owner's
Manual
Spanish, please ask your
sales
associate
or call
1-800-959-7007
@
SEARS
America's Repair Specla_ts
• Part Description
in
Pare obtener este Manual del
proplatario en espa_ol, sfrvase
solicitario a su vendedor o Ilamar al
1-800-959-7007
SEARS WARRANTY
FULL 90-DAY WARRANTY ON GARAGE DOOR OPENER
For 90 daysfromthe date of purchase,Sears willrepairthis Garage DoorOpener, free of charge,if defectiveIn materialor workmenshlp.
LIMITED WARRANTY
From the 91st day unt, oneyear from the date of purchase,Sears will fumishreplacementpartsfor any defectiveparts, free of charge.
You pay for labor.
LIMITED WARRANTY ON MOTOR
1/2HP MOTOR: After 1year and through 5 years, if the motoren this Garage Door Opener is dafectJve,Sears will furnish a replacement
motor, free of charge.You pay for labor.
1/3HP MOTOR: After 1 year and through 3 years, if the motoronthis Garage Door Opener is defective,Sears will furnisha replacement
motor,free of charge.You pay for labor.
MMITATION ON MABILn'Y
SEARS WILL NOT BE LIABLE FOR LOSS OR DAMAGE TO PROPERTY OR ANY INCIDENTAL OR CONSEQUENTIAL LOSS OR
EXPENSE FROM PROPERTY DAMAGE DUE DIRECTLY OR INDIRECTLY FROM THE USE OFTHIS PRODUCT. Some statesde
not allow the exclusionor fimitationof inck:lentaior consequentialdamages, so the above limitationor exclusionmay not applyto you.
This warrantydoes notcover lightbulbsor repairpada necessa_jbecause of operatorabuse or negligence,includingthe failure to
install,adjustand operate this garage dooropener accordingtoinstructionscontained in the owner'smanual.
WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST SEARS CENTER/DEPARTMENT IN THE UNITED
STATES.
This warrantyapses onlywhile this productis in use in the UnitedStates.
This warrantygivesyou specificlegalr;ghte,andyoumay also haveother dghtswhich vat'/from state to state.
Sears, Roebuck and Co., DepL 817WA,
114A2099E
Hoffman
@1997, All Rights Reserved
Estates, IL 60179
Printed in Mexico