Manufacturer: Williams Sound
Model:PLA-DL210
Device Type:Hearing Assist – Digital Loop Amplifier
CONTACT SUPPORT:
COMPANY NAME:
TouchPoint Logic
SUPPORT CONTACT:
Aaron Rossow
EMAIL ADDRESS:
aaron@touchpointlogic.com
PHONE:
952-401-9354
ADDRESS:
1276 Park Road, Chanhassen, MN 55317
NOTES:
GENERAL INFORMATION
SIMPLWINDOWS NAME:
Williams Sound PLA-DL210_IP Demo-CP3N.smw
CATEGORY:
(Category of device or logic)
VERSION:
Version 1.0
SUMMARY:
This module provides for basic control of the Williams Sound PLA-210 Professional
Loop Amplifier. Basic controls consist of Input Levels, Input Mute, Input and Output
VU meters, Preset Selection, and Amp Status and Loop Tests. Also reports the
customized Input channel names(changed via front panel or manufacturer software.
GENERAL NOTES:
Requires PLA-DL210 firmware version 1.141 for proper operation. RTS/CTS
Handshaking must be selected on the com port for proper operation.
CRESTRON HARDWARE REQUIRED:
MC3
SETUP OF CRESTRON HARDWARE:
MC3, Smart Graphics XPanel
VENDOR FIRMWARE:
Requires PLA-DL210 firmware version 1.141 or newer for proper operation
VENDOR SETUP:
CABLE DIAGRAM:
Straight-Through serial cable.
©2013 Crestron Electronics, Inc.
15 Volvo Drive · Rockleigh, NJ 07647
800.237.2041 / 201.767.3400
http://application.market.com
For more information please contact our Crestron Application Market team at
applicationmarket@crestron.com. The information contained on this document is privileged
and confidential and for use by Crestron Authorized Dealers, CSP Members, A+ Partners
and Certified Integrated Partners only. Specifications subject to change without notice.
Manufacturer: Williams Sound
Model:PLA-DL210
Device Type:Hearing Assist – Digital Loop Amplifier
CONTROL:
<Digital_AES_L>_Input_Vol<+/->
D
Press increase/decrease Vol by {Level_Change_Per_Hit} Parament.
<Digital_AES_L>_Input_Level
A
Assign a fader level to be sent when [xx_Send_New_Level] is pressed. Should be
driven by an Analog Initialize or Preset with Ramp Time set to 0. (Range is a
signed integer from -960 to 0, -960 being = to -96.0dB)
<Digital_AES_L>_Mute <On/Off>
D
Press Mute/Unmute the fader.
<Digital_AES_L>_Mute_Toggle
D
Press to Toggle Mute Status.
Poll<AES> State
D
Pulse to update the state of the given input (Fader Level, Mute Status, etc).
Poll_<Input/Output>_VU_Meters
D
While this input is HI, the module will ask for VU Meter data at {VU_Meter Refresh
Rate}. When signal goes low, polling will stop. Intention is to latch this signal HI
when the appropriate page is active, therefor only receiving the data when needed.
AGC_Preset-<Music/Voice/Custom>
D
Press to select a audio preset..
Loop_Test_Intiate
D
Press to run a Loop Test.
Get_Amp_Status
D
Press to get current status of Amp 1(Loop 1) and Amp 2(Loop 2).
Set_Get_Status
D
Pulse this input at startup to make the DL-210A send current status after
commands are sent. This is required for proper operation. If you don’t do this, the
unit will not reply with current volume status or mute status.
Poll
D
Pulse this on startup, after Set_Get_Status to get current status of the PLA-DL210.
This is only required once.
©2013 Crestron Electronics, Inc.
15 Volvo Drive · Rockleigh, NJ 07647
800.237.2041 / 201.767.3400
http://application.market.com
For more information please contact our Crestron Application Market team at
applicationmarket@crestron.com. The information contained on this document is privileged
and confidential and for use by Crestron Authorized Dealers, CSP Members, A+ Partners
and Certified Integrated Partners only. Specifications subject to change without notice.
Manufacturer: Williams Sound
Model:PLA-DL210
Device Type:Hearing Assist – Digital Loop Amplifier
FEEDBACK:
A
Indicates the current fader level for the input. (Signed integer from -960 to 0, -960
being = to -96.0dB)
<Digital_AES_L>_Input_Mute_FB
D
Indicates the current mute status of the input.
<Digital_AES_L>_Ch_Name
S
Reports the custom name assigned to the input via the PC/IPad/Front Panel.
Input_<AES_L>_VU Meter
A
Indicates the VU Levels for the input. For a gauge object on touchpanel. (0-65535)
Output_<Loop_A>_VU Meter
A
Indicates the VU Levels for the input. For a gauge object on touchpanel. (0-65535).
AGC_Preset-<Music/Voice/Custom>_FB
D
Indicates the active Preset.
Loop_<A/B>_Test_*
D
Reports Loop Test results.
Amp<1/2>_Temp
A
Reports the current temp of the Amps, updated every 60 seconds.
Amp,1/2>_over_<100c/125c>
D
Reports HI if temp is over * level
System(Processor_Temp)
A
Reports the current temp of the processor, updated every 60 seconds.
Amp_<1/2>_Ready/Clip Warning/Temp
over 100c/Temp over 125c/Shutdown
Fault/Enabled
D
Indicates the current status of Amp 1 & 2. Test runs automatically every 10 minutes
or when Get_Amp_Status is pulsed.
<Digital_AES_L>_Fader_Level
©2013 Crestron Electronics, Inc.
15 Volvo Drive · Rockleigh, NJ 07647
800.237.2041 / 201.767.3400
http://application.market.com
For more information please contact our Crestron Application Market team at
applicationmarket@crestron.com. The information contained on this document is privileged
and confidential and for use by Crestron Authorized Dealers, CSP Members, A+ Partners
and Certified Integrated Partners only. Specifications subject to change without notice.
Manufacturer: Williams Sound
Model:PLA-DL210
Device Type:Hearing Assist – Digital Loop Amplifier
PARAMETERS:
VU_Meter Refresh Rate
Level_Change_Per_Hit
A
Integer stating the number of times per second to report the VU Level. This creates
a lot of network traffic, use carefully! 1 to 30 times per second allowed.
A
Integer setting the amount of change for every press of the Vol+/Vol- inputs.
TESTING:
OPS USED FOR TESTING:
3 Series (MC3)
SIMPL WINDOWS USED FOR TESTING:
4.02.56.01
DEVICE DB USED FOR TESTING:
62.01.001.00
CRES DB USED FOR TESTING:
49.06.005.00
SYMBOL LIBRARY USED FOR TESTING:
508
SAMPLE PROGRAM:
Williams Sound PLA-DL210_Serial Demo-MC3
REVISION HISTORY:
Version 1.0
©2013 Crestron Electronics, Inc.
15 Volvo Drive · Rockleigh, NJ 07647
800.237.2041 / 201.767.3400
http://application.market.com
For more information please contact our Crestron Application Market team at
applicationmarket@crestron.com. The information contained on this document is privileged
and confidential and for use by Crestron Authorized Dealers, CSP Members, A+ Partners
and Certified Integrated Partners only. Specifications subject to change without notice.