VSC 100/VSC 100GX Extron’s VSC 100 & VSC 100GX convert computer scan rates up to 1024 x 768 to NTSC/PAL, S-Video and 15.75 KHZ RGBS outputs and requires no software when connected between the computer and the desired output (Projector, VCR, or any compatible video display). The VSC 100GX has the same features as the VSC 100 with the addition of Genlock, which allows its output to be synchronized to other devices, and component video output. These instructions are for both models, except where otherwise specified. Front Panel Controls & Indicators Freeze (switch & LED) - Allows for a still image capture of a scan-converted computer screen. Centering/Pan – Shifts the image up or down on the screen. (V shift, or centering) In Zoom mode, it becomes the up/down pan control. Centering/Pan – Shifts the image to the left or right on the screen. (H shift, or centering) In Zoom mode, it is the left/right pan control. Min. Max. LEDs – Flash when the range has reached a limit. Zoom/Over/Under– Selects from 3 viewing modes: Zoom, Overscan or Underscan. Use Overscan or Underscan to fit image onto the screen, or Zoom in and Pan for close-up viewing. Horz Filter – 2-position switch used to select best picture detail. Vert Filter – Select from 3 positions to eliminate flicker on output image. S-Video/RGB – Select RGB (RGBS or RGBHV) or S-Video output. An LED on the back panel will light next to the active output connector(s). (Composite video output is always active.) Signal Lock LED – Off = no signal; Blinking = out of range; On = within range. Use this procedure to connect a VGA PC or a MAC System to a VSC 100/GX. 1. Power Off – Turn computer and monitor Off and disconnect the power cord from the VSC 100/GX. 2. Outputs – Connect only the cable(s) for the desired format to the output device (RGBS, S-Video or Composite Video - Component video available on VSC 100GX). Connecting both S-Video and RGB outputs will cause a weak output signal and wrong colors may display. Composite video output is always available (may require BNC/RCA adapter 10-264-01). 3. Inputs –Adapter cable (26-462-01) is used for both the Mac and PC. Connector type and gender prevent any improper connections between the computer, monitor and VSC 100/GX. See Rear Panel connectors. a. Mac – Connect the monitor cable to the Mac Input connector. Connect adapter cable (26-462-01) from the Mac to the VGA Input on the rear . b. PC – Connect the monitor cable to the VGA Input connector. Connect adapter cable (26-462-01) from the PC to the Mac Input. 4. Connect the AC power cord to an active power source. 6. Turn computer monitor power On and then turn computer (CPU) On. 7. For the VSC 100GX, connect an external timing signal to the Genlock input. Use the Genlock output to daisy-chain the timing signal to another device, or install terminator if no other device. See User's Manual (68-395-01) for details on Genlock connectors and controls. CONNECTIONS 100-240V 0.9A 50/60 Hz Genlock OUT or Terminator GENLOCK INPUTS Outputs (see rear panel) MAC a. Composite (NTSC/PAL) - A BNC connector for NTSC or PAL composite video, depending on the position of the PAL Out DIP switch on the rear panel. This output is always available. Use BNC/ RCA adapter (10-264-01) if required. b. S-Video - A 4-pin mini-din connector outputs S-Video or Hi-8 style video. The LED lights when this output is active. c. RGBS or RGBHV- 4 BNC connectors provide Red, Green, Blue and Composite Sync, or use all 5 BNCs to include separate Horizontal and Vertical sync. The LED lights when this output is active. d. The VSC 100GX also provides a component video output which is activated by the R-Y/Y/B-Y–RGBS DIP switch on the rear panel. This uses BNC connectors marked: R-Y, Y and B-Y. INSTALLATION R-Y/Y/B-Y OUT HV OUT PAL OUT 75 OHM OPERATION VGA PC Video Out VGA IN COMPOSITE S-VIDEO EXTRON ELECTRONICS / RGB SYSTEMS 1230 South Lewis Street Anaheim, CA 92805 714.491.1500 FAX 714.491.1517 U.S.A. B/B-Y H/HV V INPUTS LCD Projector Videoconferencing System MAC INPUTS Beta Cam Tape Deck MAC VGA 6' R-Y/Y/B-Y OUT HV OUT PAL OUT 75 OHM R-Y/Y/B-Y Out (GX only) – Down = RGBS/RGBHV video out; Up = Component video out. Use R, G and B output connectors. HV Out – Down for RGBS out; Up for RGBHV out. PAL Out Switch – Down for selection of NTSC (525 lines); Up for PAL video output (625 lines). 75 Ohm DIP Switch (rear panel) - monitor termination: Down = using local monitor (Hi-Z) Up (75 Ohm) = not using a local monitor. G/Y Component (GX only) R-Y, Y, B-Y VGA DIP Switches (see rear panel) R/R-Y NTSC/PAL MAC Monitor (always active) VGA 6' OUT OUTPUTS Monitor Data Monitor MAC Video Editor PC Monitor EXTRON ELECTRONICS, EUROPE Beeldschermweg 6C 3821 AH Amersfoort +31.33.453.4040 FAX +31.33.453.4050 The Netherlands MAC Video Out VCR EXTRON ELECTRONICS, ASIA 41B Kreta Ayer Road Singapore 089003 +65.226.0015 FAX +65.226.0019 Singapore Note: Do NOT connect cables for both S-Video and RGB/R-Y,Y,B-Y at the same time. 89-08 33-443-01 Rev A Printed in USA.