Dolby Laboratories KH 02 Owner`s manual

OWNER’S MANUAL
LED TV*
*LG LED TV applies LCD screen with LED backlights.
Please read this manual carefully before operating your set and retain it
for future reference.
LY75**
LY76**
www.lg.com
2
TABLE OF CONTENTS
ENG
ENGLISH
TABLE OF CONTENTS
3
LICENSES
24
TROUBLESHOOTING
3
OPEN SOURCE SOFTWARE
NOTICE
25
SPECIFICATIONS
4
ASSEMBLING AND PREPARING
28
IR CODES
4
5
7
8
9
10
10
11
12
13
14
Unpacking
Separate Purchase
Parts and Button
Using the Joystick Button
Lifting and Moving the TV
Setting up the TV
- Attaching the Stand
- Tidying Cables
- Mounting on a Table
- Mounting on a Wall
- How to use Dual Lock™
29
EXTERNAL CONTROL DEVICE
SETUP
29
29
RS-232C Setup
Type of Connector:
D-Sub 9-Pin Male
RS-232C Configurations
Communication Parameters
Command Reference List
Transmission / Receiving Protocol
15
MAKING CONNECTIONS
15
16
16
16
17
18
18
19
19
19
20
20
20
Antenna Connection
Satellite Dish Connection
LED Clock Connection
Euro Scart Connection
HDMI Connection
Network Setup
- Wired network Connection
Speaker Output Setup
Audio Connection
- Digital Optical Audio Connection
CI module Connection
USB Connection
Headphone Connection
21
REMOTE CONTROL
23
MAINTENANCE
23
23
23
Cleaning your TV
- Screen, Frame, Cabinet and Stand
- Power Cord
29
30
30
31
WARNING
yy If you ignore the warning message, you
may be seriously injured or there is a
possibility of accident or death.
CAUTION
yy If you ignore the caution message, you
may be slightly injured or the product may
be damaged.
NOTE
yy The note helps you understand and use
the product safely. Please read the note
carefully before using the product.
LICENSES / OPEN SOURCE SOFTWARE NOTICE
Supported licenses may differ by model. For more information about licenses, visit www.lg.com.
Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the
HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in
the United States and other countries.
ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a
subsidiary of Rovi Corporation. This is an official DivX Certified® device that has
passed rigorous testing to verify that it plays DivX video. Visit divx.com for more
information and software tools to convert your files into DivX videos.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be
registered in order to play purchased DivX Video-on-Demand (VOD) movies.
To obtain your registration code, locate the DivX VOD section in your device
setup menu. Go to vod.divx.com for more information on how to complete your
registration.
“DivX Certified® to play DivX® video up to HD 1080p, including premium content.”
“DivX®, DivX Certified® and associated logos are trademarks of Rovi
Corporation or its subsidiaries and are used under license.”
“Covered by one or more of the following U.S. patents :
7,295,673; 7,460,668; 7,515,710; 7,519,274”
For DTS patents, see http://patents.dts.com. Manufactured under license from
DTS Licensing Limited. DTS, the Symbol, & DTS and the Symbol together are
registered trademarks, and DTS 2.0+Digital Out is a trademark of DTS, Inc. ©
DTS, Inc. All Rights Reserved.
OPEN SOURCE SOFTWARE NOTICE
To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in
this product, please visit http://opensource.lge.com.
In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are
available for download.
LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of
performing such distribution (such as the cost of media, shipping and handling) upon email request to
opensource@lge.com. This offer is valid for three (3) years from the date on which you purchased the
product.
ENGLISH
ENG
LICENSES
3
4
ASSEMBLING AND PREPARING
ENG
ENGLISH
NOTE
yy Image shown may differ from your TV.
yy Your TV’s OSD (On Screen Display) may differ slightly from that shown in this manual.
yy The available menus and options may differ from the input source or product model that you are
using.
yy New features may be added to this TV in the future.
yy The TV can be placed in standby mode in order to reduce the power consumption. And the TV
should be turned off if it will not be watched for some time, as this will reduce energy consumption.
yy The energy consumed during use can be significantly reduced if the level of brightness of the
picture is reduced, and this will reduce the overall running cost.
ASSEMBLING AND PREPARING
Unpacking
Check your product box for the following items. If there are any missing accessories, contact the local
dealer where you purchased your product. The illustrations in this manual may differ from the actual
product and item.
CAUTION
yy Do not use any unapproved items to ensure the safety and product life span.
yy Any damage or injuries caused by using unapproved items are not covered by the warranty.
yy Some models have a thin film attached on to the screen and this must not be removed.
NOTE
yy The items supplied with your product may vary depending on the model.
yy Product specifications or contents of this manual may be changed without prior notice due to
upgrade of product functions.
yy For an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm
thick and 18 mm width. Use an extension cable that supports USB 2.0 if the USB cable or USB
FLASH DRIVE does not fit into your TV’s USB port.
B
B
A
A
*A <
= 10 mm
*B <
= 18 mm
GLISH
ENG
NGLISH
ENG
ASSEMBLING AND PREPARING
Owner’s manual
Cable Holder
(Depending on model)
Power cord
(Depending on model)
Stand Screws
4EA, M4 x L14
(Except for
32LY76**, 32LY75**)
Stand Screws
4EA, M4 x L20
(Only
32LY76**, 32LY75**)
Cable Managements
2EA
Wall mount spacers
2EA
(Only
42LY76**, 42LY75**)
or
Isolator
(Depending on model)
Stand Base
Dual Lock™
(Depending on model)
Separate Purchase
Separate purchase items can be changed or modified for quality improvement without any notification.
Contact your dealer to buy these items.
These devices only work with certain models.
LG Audio Device
Magic Remote
AN-MR300 (Only LY75**)
AN-MR500 (Only LY76**)
LED Clock
LEC-003
The model name or design may be changed depending on the upgrade of product functions,
manufacturer’s circumstances or policies.
ENGLISH
ENG
Remote control,
Batteries (AAA)
5
6
ASSEMBLING AND PREPARING
ENG
ENGLISH
NOTE
yy Antenna Isolator Installation Guide
-- Use this to install TV in a place where there is a voltage difference between TV Set and GND
of antenna signal.
»» If there is a voltage difference between TV Set and GND of antenna signal, the antenna
contact might be heated and excessive heat might cause an accident.
-- You can improve the safety when watching TV by efficiently removing power voltage from TV
antenna. It is recommended to mount the isolator to the wall. If it cannot be mounted to the
wall, mount it on the TV. Avoid disconnecting the antenna Isolator after installation.
-- Before starting, be sure that the TV antenna is connected.
Connect to TV.
Wall
ANTENNA/
CABLE IN
Cable / Antenna
or
Isolator
Connect to Set-Top box.
Connect one end of the isolator to cable/antenna jack and the other to TV set or set-top box.
“Equipment connected to the protective earthing of the building installation through the mains
connection or through other equipment with a connection to protective earthing - and to a cable
distribution system using coaxial cable, may in some circumstances create a fire hazard. Connection
to a cable distribution system has therefore to be provided through a device providing electrical
isolation below a certain frequency range (galvanic isolator, see EN 60728-11)”
When applying the RF Isolator, a slight loss of signal sensitivity can occur.
ASSEMBLING AND PREPARING
Screen
Speakers
Remote control sensor
Power Indicator
Joystick button
(* This button is located below the TV screen.)
NOTE
yy You can set the power indicator light to on or off by selecting OPTION in the main menus.
ENGLISH
ENG
Parts and Button
7
8
ASSEMBLING AND PREPARING
ENG
ENGLISH
Using the Joystick Button
You can simply operate the TV functions, pressing or moving the joystick button up, down, left or right.
Basic Functions
Power On
When the TV is turned off, place your finger on the joystick
button and press it once and release it.
Power Off
When the TV is turned on, place your finger on the joystick
button and press it once for a few seconds and release it.
Volume Control
If you place your finger over the joystick button and move
it left or right, you can adjust the volume level you want.
Programmes
Control
If you place your finger over the joystick button and
move it up or down, you can scrolls through the saved
programmes you want.
NOTE
yy When your finger over the joystick button and push it to the up, down, left or right, be careful not to
press the joystick button. If you press the joystick button first, you can not adjust the volume level
and saved chennels.
Adjusting the Menu
(Only LY76**)
When the TV is turned on, press the joystick button one time.
You can adjust the Menu items ( , ,
, ) moving the joystick button up, down, left or right.
TV Off
Turn the power off.
Settings
Accesses the main menu.
Input List Changes the input source.
Close
Clears on-screen displays and return to TV viewing.
ASSEMBLING AND PREPARING
9
Please note the following advice to prevent the
TV from being scratched or damaged and for safe
transportation regardless of its type and size.
yy When transporting a large TV, there should
be at least 2 people.
yy When transporting the TV by hand, hold the
TV as shown in the following illustration.
CAUTION
yy Avoid touching the screen at all times, as
this may result in damage to the screen.
yy It is recommended to move the TV in the
box or packing material that the TV originally
came in.
yy Before moving or lifting the TV, disconnect
the power cord and all cables.
yy When holding the TV, the screen should face
away from you to avoid damage.
yy Hold the top and bottom of the TV frame
firmly. Make sure not to hold the transparent
part, speaker, or speaker grill area.
yy When transporting the TV, do not expose the
TV to jolts or excessive vibration.
yy When transporting the TV, keep the TV
upright, never turn the TV on its side or tilt
towards the left or right.
yy Do not apply excessive pressure to cause
flexing /bending of frame chassis as it may
damage screen.
ENGLISH
ENG
Lifting and Moving the TV
10 ASSEMBLING AND PREPARING
ENG
ENGLISH
Setting up the TV
Attaching the Stand
* Image shown may differ from your TV.
1
3
M4 x L14
(Except for
32LY76**, 32LY75**)
2
4EA
M4 x L20
(Only
32LY76**, 32LY75**)
A Stand Base
CAUTION
B Stand Base
yy When attaching the stand to the TV, place
the screen facing down on a cushioned
table or flat surface to protect the screen
from scratches.
ASSEMBLING AND PREPARING
* Image shown may differ from your TV.
1
2
Gather and bind the cables with the cable
Holder and the cable Managements.
Fix the cable Managements firmly to the TV.
Cable Holder
Cable Management
CAUTION
yy Do not move the TV by holding the cable
holders, as the cable holders may break,
and injuries and damage to the TV may
occur.
ENGLISH
ENG
Tidying Cables
11
12 ASSEMBLING AND PREPARING
ENG
ENGLISH
Mounting on a Table
1
Securing the TV to a Wall
Lift and tilt the TV into its upright position on
a table.
-- Leave a 10 cm (minimum) space from
the wall for proper ventilation.
(This feature is not available for all models.)
10 cm
10 cm
2
10 cm
10 cm
Connect the power cord to a wall outlet.
1
CAUTION
yy Do not place the TV near or on sources
of heat, as this may result in fire or other
damage.
2
3
Using the Kensington security system
(This feature is not available for all models.)
The Kensington security system connector is
located at the rear of the TV. For more information
of installation and using, refer to the manual
provided with the Kensington security system or
visit http://www.kensington.com.
Connect the Kensington security system cable
between the TV and a table.
Insert and tighten the eye-bolts, or TV
brackets and bolts on the back of the TV.
-- If there are bolts inserted at the eyebolts position, remove the bolts first.
Mount the wall brackets with the bolts to the
wall.
Match the location of the wall bracket and the
eye-bolts on the rear of the TV.
Connect the eye-bolts and wall brackets
tightly with a sturdy rope.
Make sure to keep the rope horizontal with
the flat surface.
CAUTION
yy Make sure that children do not climb on
or hang on the TV.
NOTE
yy Use a platform or cabinet that is strong
and large enough to support the TV
securely.
yy Brackets, bolts and ropes are not
provided. You can obtain additional
accessories from your local dealer.
ASSEMBLING AND PREPARING 13
CAUTION
Attach an optional wall mount bracket at the rear
of the TV carefully and install the wall mount
bracket on a solid wall perpendicular to the
floor. When you attach the TV to other building
materials, please contact qualified personnel.
LG recommends that wall mounting be performed
by a qualified professional installer.
10 cm
10 cm
10 cm
10 cm
NOTE
Make sure to use screws and wall mount bracket
that meet the VESA standard. Standard
dimensions for the wall mount kits are described
in the following table.
Separate Purchase(Wall Mounting Bracket)
Model
32/39LY76** 42/47/55LY76**
32/39LY75** 42/47/55LY75**
VESA (A x B)
200 x 200
400 x 400
Standard screw
M6
M6
Number of screws
4
4
Wall mount
bracket
LSW240B
MSW240
LSW440B
MSW240
A
B
yy Disconnect the power first, and then
move or install the TV. Otherwise electric
shock may occur.
yy If you install the TV on a ceiling or slanted
wall, it may fall and result in severe injury.
Use an authorized LG wall mount and
contact the local dealer or qualified
personnel.
yy Do not over tighten the screws as this
may cause damage to the TV and void
your warranty.
yy Use the screws and wall mounts that
meet the VESA standard. Any damages
or injuries by misuse or using an
improper accessory are not covered by
the warranty.
yy Use the screws that are listed on the
VESA standard screw specifications.
yy The wall mount kit includes an
installation manual and necessary parts.
yy The wall mount bracket is not provided.
You can obtain additional accessories
from your local dealer.
yy The length of screws may differ
depending on the wall mount. Make
sure to use the proper length.
yy For more information, refer to the
manual supplied with the wall mount.
ENGLISH
ENG
Mounting on a Wall
14 ASSEMBLING AND PREPARING
ENG
ENGLISH
NOTE
yy Only 42LY76**, 42LY75**
Wall Mount Spacers
How to use Dual Lock™
(Depending on model)
Fix the set-top box to the TV and use it when you
want to.
1
After removing the protection paper from the
Dual Lock, stick it to the TV and the set-top
box as shown.
Dual Lock™
2
Attach the set-top box to the TV by pressing
the Velcro strips together.
NOTE
lease make sure no foreign substances
yy P
exist on the surface of the product, and
then firmly attach the Dual Lock.
yy Before attaching the set-top box to the
TV set, let the attached Dual Lock dry for
at least three days.
MAKING CONNECTIONS 15
* Image shown may differ from your TV.
* Any separate cable is not provided.
This section on MAKING CONNECTIONS mainly
uses diagrams for the LY75** models.
Connect various external devices to the TV
and switch input modes to select an external
device. For more information on external device’s
connection, refer to the manual provided with
each device.
Available external devices are: HD receivers,
DVD players, VCRs, audio systems, USB storage
devices, PC, gaming devices, and other external
devices.
Antenna Connection
Connect the TV to a wall antenna socket with an
RF cable (75 Ω).
ANTENNA/
CABLE IN
Wall Antenna
Socket
NOTE
yy The external device connection may differ
from the model.
yy Connect external devices to the TV
regardless of the order of the TV port.
yy If you record a TV program on a DVD
recorder or VCR, make sure to connect
the TV signal input cable to the TV
through a DVD recorder or VCR. For
more information on recording, refer to
the manual provided with the connected
device.
yy Refer to the external equipment’s manual
for operating instructions.
yy If you connect a gaming device to the TV,
use the cable supplied with the gaming
device.
yy In PC mode, there may be noise
associated with the resolution, vertical
pattern, contrast or brightness. If noise is
present, change the PC output to another
resolution, change the refresh rate to
another rate or adjust the brightness and
contrast on the PICTURE menu until the
picture is clear.
yy In PC mode, some resolution settings
may not work properly depending on the
graphics card.
yy Only a USB storage device is
recognizable.
yy If the USB storage device is connected
through a USB hub, the device is not
recognizable.
(*Not Provided)
NOTE
yy Use a signal splitter to use more than 2
TVs.
yy If the image quality is poor, install a signal
amplifier properly to improve the image
quality.
yy If the image quality is poor with an
antenna connected, try to realign the
antenna in the correct direction.
yy An antenna cable and converter are not
supplied.
yy Supported DTV Audio: MPEG, Dolby
Digital, Dolby Digital Plus, HE-AAC
ENGLISH
ENG
MAKING CONNECTIONS
E CONTROL
2
Transmits the video and audio signals from
an external device to the TV set. Connect the
external device and the TV set with the euro scart
cable as shown.
Connect the TV to a satellite dish to a satellite
socket with a satellite RF cable (75 Ω).
AV
H/P OUT
(RGB)
CLOCK
13/18V
700mA Max
LNB
Satellite IN
RS-232C IN
ANTENNA/
CABLE IN
Satellite
Dish
(CONTROL & SERVICE)
-
REO (8 Ω)
PCMCIA CARD SLOT
(Only satellite models)
/DVI
IN
AUDIO IN
OPTICAL
(COMPONENT/RGB/DVI) AUDIO OUT
KER OUT
Euro Scart Connection
IN 3
NENT
Satellite Dish Connection
USB IN
ENG
ENGLISH
1
16 MAKING CONNECTIONS
AV
IN / OUT
(*Not Provided)
(*Not Provided)
LED Clock Connection
AUDIO / VIDEO
This TV can be connected to a LED Clock via the
CLOCK port.
Current
input mode
AUX LAN
LAN
SPEAKER OUT
CLOCK
Digital TV
IN 1(ARC)
VOLUME STEREO
CONTROL (8 Ω)
Component
LED
(*Not Provided)
RS-232C IN
(CONTROL & SERVICE)
AV
IN / OUT
Digital TV
Analogue TV
HDMI
1
CLOCK
AV1
(TV Out1)
Analogue TV, AV
OPTICAL
DIGITAL
AUDIO OUT
13/18V
700mA Max
ANTENNA/
LNB
Satellite
INe CABLE IN
Clock
Output
Type
TV Out : Outputs Analogue TV or Digital TV
signals.
NOTE
y Any Euro scart cable used must be signal
shielded.
+
+
HDMI Connection
PCMCIA Card
(Only LY76**)
USB IN 2
Transmits the digital video and audio signals
from your PC to the TV. Connect the PC and the
TV with the HDMI cable as shown. Choose any
HDMI input port to connect. It does not matter
which port you use.
SPEAKER OUT
USB IN 1
-
USB IN 1
USB HUB
HUB
Mobile Phone
Mobile
USB Phone
USB
(*Not Provided)
HUB
Mobile Ph
Mobile Pho
PCMCIA Card
HDMI
PCMCIA Card
IN
2 (MHL)
(*Not Provided)
PCMCIA Card
H/P OUT
DVD / Blu-Ray /
HD Cable Box / HD STB / PC
AV
IN / OUT
USB IN 2
13/18V
700mA Max
ANTENNA/
LNB
Satellite INe CABLE IN
HDMI
AV
IN / OUT
USB IN 2
RS-232C IN
(CONTROL & SERVICE)
USB IN 1
CLOCK
Headphone
13/18V
700mA Max
ANTENNA/
LNB
Satellite INe CABLE IN
IN
2 (MHL)
OPTICAL
DIGITAL
AUDIO OUT
H/P OUT
IN 1
OPTICAL
DIGITAL
AUDIO OUT
DVD / Blu-Ray /
HD Cable
BoxPhone
/ HD STB / PC
Mobile
(*Not Provided)
H/P OUT
SPEAKER OUT
+
CLOCK
VOLUME STEREO
CONTROL (8 Ω)
IN 1(ARC)
VOLUME STEREO
CONTROL (8 Ω)
USB IN 2
-
LAN
USB IN 1
+
HUB
IN
2 (MHL)
IN
2 (ARC)
AUX LAN
USB
OUT
(Only LY75**)
-
-
ENGLISH
ENG
C IN
SERVICE)
MAKING CONNECTIONS 17
18 MAKING CONNECTIONS
ENG
ENGLISH
NOTE
yy It is recommended to use the TV with
the HDMI connection for the best image
quality.
yy Use the latest High Speed HDMI™ Cable
with CEC (Customer Electronics Control)
function.
yy High Speed HDMI™ Cables are tested
to carry an HD signal up to 1080p and
higher.
yy Supported HDMI Audio format : Dolby
Digital, PCM (Up to 192 kHz, 32 kHz/
44.1 kHz/48 kHz/88 kHz/96 kHz/
176 kHz/192 kHz, DTS)
ARC (Audio Return Channel)
yyAn external audio device that supports
SIMPLINK and ARC must be connected
using HDMI IN (ARC) port.
yyWhen connected with a high-speed
HDMI cable, the external audio device
that supports ARC outputs optical SPDIF
without additional optical audio cable and
supports the SIMPLINK function.
Network Setup
Wired network Connection
This TV can be connected to a Pro:Centric server
via the LAN port. After making the physical connection, the TV needs to be set up for network
communication.
Connect the LAN port of the Modem or Router
from Pro:Centric server to the LAN port on the TV.
AUX LAN
LAN
(*Not Provided)
2
1
Broadband Modem
Pro:CentricServer
Router
Broadband Modem
Pro:CentricServer
1
Connect the LAN port of the Modem or
Router to the LAN port on the TV.
2
Connect the LAN port of the PC to the AUX
LAN port on the TV.
CAUTION
yy Do not connect a modular phone cable to
the LAN port.
yy Since there are various connection
methods, please follow the specifications of
your telecommunication carrier or internet
service provider.
MAKING CONNECTIONS 19
Audio Connection
Connect the external speaker to the SPEAKER
OUT jack on the TV.
You may use an optional external audio system
instead of the built-in speaker.
Digital Optical Audio Connection
Transmits a digital audio signal from the TV to an
external device. Connect the external device and
the TV with the optical audio cable as shown.
AUX LAN
LAN
IN 1(ARC)
VOLUME STEREO
CONTROL (8 Ω)
SPEAKER OUT
CLOCK
(*Not Provided)
VOLUME
CONTROL
AUX LAN
LAN
SPEAKER OUT
CLOCK
13/18V
700mA Max
ANTENNA/
LNB
Satellite INe CABLE IN
CLOCK
+
RS-232C IN
(CONTROL & SERVICE)
STEREO
(8Ω)
+
UP
AV
DOWN
IN / OUT
Control port for Speaker out
-
-
GND
RIGHT
LEFT
GND
Method of Volume control port
*Cable Spec.
Each Up/ Down pin is pulled
to 3.3V with CPU GPIO.
GND / Up / Down
CPU detects transition
from 3.3V to GND level for
volume control.
(*Not
CLOCK
IN 1(ARC)
VOLUME STEREO
CONTROL (8 Ω)
OPTICAL
DIGITAL
AUDIO OUT
RS-232C IN
(CONTROL & SERVICE)
OPTICAL
DIGITAL
AUDIO OUT
13/18V
700mA Max
ANTENNA/
LNB
e
Provided)Satellite IN CABLE IN
AV
IN / OUT
OPTICAL AUDIO IN
Digital Audio Systerm
NOTE
y Do not look into the optical output port.
Looking at the laser beam may damage
your vision.
y Audio with ACP (Audio Copy Protection)
function may block digital audio output.
ENGLISH
ENG
Speaker Output Setup
20 MAKING CONNECTIONS
PCMCIAPCMCIA
Card Card
Transmits the headphone signal from
the TV to
USB
an external device. Connect the external device
and the TV with the headphone as shown.
HUB
USB IN 2
USB
NOTE
USB IN 1
HUB
IN
2 (MHL)
yy Check if the CI module is inserted into the
PCMCIA cardUSB
slot in the right direction. If
the module is not inserted properly, this
can cause damage to the TV and the
PCMCIA card slot.
H/P OUT
HUB
USB Connection
USB IN 1
IN
2 (MHL)
HUB
Mobil
Mobile
H/P OUT
IN
2 (MHL)
(*Not Provided)
PCMCIA Card
USB
H/P OUT
PCMCIA Card
USB IN 2
View the encrypted (pay) services in digital
TV mode. This feature is not available in all
countries.
USB IN 2
Headphone Connection
USB IN 1
ENG
ENGLISH
CI module Connection
(*Not Provided)
NOTE
yy AUDIO menu items are disabled when
connecting a headphone.
yy When changing AV MODE with a
headphone connected, the change is
applied to video but not to audio.
yy Optical Digital Audio Out is not available
Mobile Phone
when connecting a headphone.
yy Headphone impedance: 16 Ω
yy Max audio output of headphone: 9mW to
15 mW
yy Headphone jack size: 0.35 cm
Connect a USB storage device such as s USB
flash memory, external hard drive or a USB
memory card reader to the TV and access the
My media menu to use various multimedia files.
Mobile Phone
USB IN 2
PCMCIA Card
USB
IN
2 (MHL)
USB IN 1
HUB
(*Not Provided)
Mobile Phone
REMOTE CONTROL 21
This item is not included for all models.
The descriptions in this manual are based on the buttons on the remote control.
Please read this manual carefully and use the TV correctly.
To replace batteries, open the battery cover, replace batteries (1.5 V AAA)
matching the
and
ends to the label inside the compartment, and close
the battery cover.
To remove the batteries, perform the installation actions in reverse.
CAUTION
yy Do not mix old and new batteries, as this may damage the remote control.
Make sure to point the remote control toward the remote control sensor on the TV.
(Only LY75**)
(POWER) Turns the TV on or off.
ENERGY
AV MODE
ꕊ ENERGY SAVING Adjusts the brightness of the screen to reduce energy consumption.
AV MODE Selects an AV mode.
INPUT
TV/
RAD
INPUT Changes the input source.
SAVING
1
2
3
TV/RAD
4
5
6
Number buttons Enters numbers.
7
8
9
Q.VIEW Returns to the previously viewed programme.
LIST
0
Q.VIEW
LIST Accesses the saved programme list.
+
RATIO Resizes an image.
P
MUTE
GUIDE
- Adjusts the volume level.
FAV Accesses your favourite programme list.
FAV
RATIO
Selects Radio, TV and DTV programme.
P
A
G
E
MUTE
PAGE
PORTAL INFO
Mutes all sounds.
ꕌPꕍ Scrolls through the saved programmes or channels.
Moves to the previous or next screen.
GUIDE Shows programme guide.
PORTAL Displays and removes hotel interactive menu.
INFO
OK
Views the information of the current programme and screen.
Navigation buttons (up/down/left/right) Scrolls through menus or options.
OK
Selects menus or options and confirms your input.
SETTINGS Selects a menu. Clears all on-screen displays and returns to TV viewing
EXIT
from any menu.
Returns to the previous level.
EXIT
Clears on-screen displays and return to TV viewing.
Coloured buttons These access special functions in some menus.
Teletext buttons (
Q.MENU
AD
ALARM
TEXT/T.OPT) These buttons are used for teletext.
SUBTITLE Recalls your preferred subtitle in digital mode.
Control buttons (
)
Controls the MY MEDIA menus, or the
SIMPLINK compatible devices (USB,SIMPLINK).
Accesses the AV devices connected with the HDMI cable through
HDMI-CEC. Opens the SIMPLINK menu.
Q.MENU Accesses the Quick menus.
AD
By Pressing AD button, audio descriptions function will be enabled.
ALARM Sets the alarm function.
ENGLISH
ENG
REMOTE CONTROL
22 REMOTE CONTROL
ENG
ENGLISH
(Only LY76**)
(POWER) Turns the TV on or off.
ENERGY
AV MODE
ꕊ ENERGY SAVING Adjusts the brightness of the screen to reduce energy consumption.
AV MODE Selects an AV mode.
INPUT
TV/
RAD
INPUT Changes the input source.
SAVING
1
2
3
TV/RAD
Selects Radio, TV and DTV programme.
4
5
6
Number buttons Enters numbers.
7
8
9
Q.VIEW Returns to the previously viewed programme.
LIST
0
Q.VIEW
LIST Accesses the saved programme list.
+
- Adjusts the volume level.
SMART Accesses the Smart Home menus.
RATIO Resizes an image.
RATIO
P
MUTE
GUIDE
P
A
G
E
MUTE
PAGE
PORTAL INFO
Mutes all sounds.
ꕌPꕍ Scrolls through the saved programmes or channels.
Moves to the previous or next screen.
GUIDE Shows programme guide.
PORTAL Displays and removes hotel interactive menu.
INFO
OK
Views the information of the current programme and screen.
Navigation buttons (up/down/left/right) Scrolls through menus or options.
OK
Selects menus or options and confirms your input.
SETTINGS Selects a menu. Clears all on-screen displays and returns to TV viewing
EXIT
from any menu.
Returns to the previous level.
EXIT
Clears on-screen displays and return to TV viewing.
Coloured buttons These access special functions in some menus.
Teletext buttons (
Q.MENU
AD
ALARM
TEXT/T.OPT) These buttons are used for teletext.
SUBTITLE Recalls your preferred subtitle in digital mode.
Control buttons (
)
Controls the MY MEDIA menus, or the
SIMPLINK compatible devices (USB,SIMPLINK).
Used for viewing 3D video.
Q.MENU Accesses the Quick menus.
AD By Pressing AD button, audio descriptions function will be enabled.
ALARM Sets the alarm function.
MAINTENANCE 23
Cleaning your TV
Clean your TV regularly to keep the best performance and to extend the product lifespan.
CAUTION
yy Make sure to turn the power off and disconnect the power cord and all other cables first.
yy When the TV is left unattended and unused for a long time, disconnect the power cord from the
wall outlet to prevent possible damage from lightning or power surges.
Screen, Frame, Cabinet and Stand
yy To remove dust or light dirt, wipe the surface with a dry, clean, and soft cloth.
yy To remove major dirt, wipe the surface with a soft cloth dampened in clean water or a diluted mild
detergent. Then wipe immediately with a dry cloth.
CAUTION
yy Avoid touching the screen at all times, as this may result in damage to the screen.
yy Do not push, rub, or hit the screen surface with your fingernail or a sharp object, as this may result
in scratches and image distortions.
yy Do not use any chemicals as this may damage the product.
yy Do not spray liquid onto the surface. If water enters the TV, it may result in fire, electric shock, or
malfunction.
Power Cord
Remove the accumulated dust or dirt on the power cord regularly.
ENGLISH
ENG
MAINTENANCE
24 TROUBLESHOOTING
ENG
ENGLISH
TROUBLESHOOTING
The software version can be updated for improvement in performance.Customer needs to ensure the
compatibility of customer’s equipment with LGE software. If needed, please consult with LGE and upload
revised software version according to the guidance provided by LGE.
Problem
Solution
Cannot control the
TV with the remote
control.
yy Check the remote control sensor on the product and try again.
yy Check if there is any obstacle between the product and the remote control.
to ,
to
yy Check if the batteries are still working and properly installed (
No image display
and no sound is
produced.
yy Check if the product is turned on.
yy Check if the power cord is connected to a wall outlet.
yy Check if there is a problem in the wall outlet by connecting other products.
The TV turns off
suddenly.
yy Check the power control settings. The power supply may be interrupted.
yy Check if the Automatic Standby (Depending on model) / Sleep Timer / Time
Power Off is activated in the TIME settings.
When connecting to
the PC (RGB/HDMI
DVI), ‘No signal’ or
‘Invalid Format’ is
displayed.
yy Turn the TV off/on using the remote control.
yy Reconnect the RGB/HDMI cable.
yy Restart the PC with the TV on.
).
SPECIFICATIONS
Product specifications may be changed without prior notice due to upgrade of product functions.
MODELS
32LY76**
39LY76**
42LY76**
32LY760H-ZA
39LY760H-ZA
42LY760H-ZA
Dimensions
(W x H x D)
With stand (mm)
732 x 481 x 207
885 x 567 x 218
961 x 612 x 218
Without stand (mm)
732 x 431 x 55.5
885 x 524 x 55.5
961 x 567 x 55.5
Weight
With stand (kg)
6.2
8.3
9.5
Without stand (kg)
6.0
8.0
9.2
Power requirement
Power consumption
MODELS
AC 100-240 V~ 50 / 60 Hz
75 W
100 W
110 W
47LY76**
55LY76**
32LY75**
47LY760H-ZA
55LY760H-ZA
32LY750H-ZA
Dimensions
(W x H x D)
With stand (mm)
1073 x 676 x 247
1243 x 772 x 247
732 x 481 x 207
Without stand (mm)
1073 x 629 x 55.8
1243 x 725 x 56.8
732 x 431 x 55.5
Weight
With stand (kg)
12.7
18.4
6.2
Without stand (kg)
12.3
18.0
6.0
Power requirement
Power consumption
MODELS
AC 100-240 V~ 50 / 60 Hz
120 W
140 W
75 W
39LY75**
42LY75**
47LY75**
39LY750H-ZA
42LY750H-ZA
47LY750H-ZA
Dimensions
(W x H x D)
With stand (mm)
885 x 567 x 218
961 x 612 x 218
1073 x 676 x 247
Without stand (mm)
885 x 524 x 55.5
961 x 567 x 55.5
1073 x 629 x 55.8
Weight
With stand (kg)
8.3
9.5
12.7
Without stand (kg)
8.0
9.2
12.3
Power requirement
Power consumption
MODELS
AC 100-240 V~ 50 / 60 Hz
100 W
55LY75**
55LY750H-ZA
Dimensions
(W x H x D)
With stand (mm)
1243 x 772 x 247
Without stand (mm)
1243 x 725 x 56.8
Weight
With stand (kg)
Without stand (kg)
18.4
18.0
Power requirement
AC 100-240 V~ 50 / 60 Hz
Power consumption
140 W
110 W
120 W
ENGLISH
ENG
SPECIFICATIONS
25
26 SPECIFICATIONS
ENG
ENGLISH
CI Module Size
(W x H x D)
100.0 mm x 55.0 mm x 5.0 mm
Operating Temperature
Environment
condition
0 °C to 40 °C
Operating Humidity
Less than 80 %
Storage Temperature
-20 °C to 60 °C
Storage Humidity
Less than 85 %
Satellite Digital TV1
Digital TV
Analogue TV
DVB-T/T2
DVB-C
DVB-S/S2
DVB-T
DVB-C
PAL/SECAM B/G/D/K,
PAL I/I’,
SECAM L/L’2
VHF, UHF
C-Band, Ku-Band
VHF, UHF
VHF: E2 to E12,
UHF : E21 to E69,
CATV: S1 to S20,
HYPER: S21 to S47
Television system
Programme coverage
Maximum number of storable
programmes
6,000
1,500
External antenna impedance
1
2
75 Ω
Satellite and DVB-T2 support models
Except for DVB-T2 support models
(Only LY76**)
Wireless module(LGSBW41) Specifications
Wireless LAN module
Bluetooth module
Standard
IEEE 802.11a/b/g/n
Standard
Bluetooth Version 3.0
Frequency
ragne
2400 to 2483.5 MHz
5150 to 5250 MHz
5725 to 5850 MHz(for Non EU)
Frequency
ragne
2400 to 2483.5 MHz
Output
power(Max.)
802.11a: 13 dBm
802.11b: 15 dBm
802.11g: 14 dBm
802.11n - 2.4GHz: 16 dBm
802.11n - 5GHz: 16 dBm
Output
power(Max.)
10 dBm or Lower
yyBecause band channel used by the country could be different, the user can not change or adjust
the operating frequency and this product is set for the regional frequency table.
yyThis device should be installed and operated with minimum distance 20 cm between the device and your body.
And this phrase is for the general statement for consideration of user environment.
SPECIFICATIONS
27
ENGLISH
ENG
(Only LY75**)
Wireless LAN module(TWFM-B006D) specification
Standard
IEEE802.11a/b/g/n
2400 to 2483.5 MHz
5150 to 5250 MHz
5725 to 5850 MHz (for Non EU)
Frequency Range
802.11a: 11 dBm
802.11b: 14 dBm
802.11g: 10.5 dBm
802.11n - 2.4GHz: 11 dBm
802.11n - 5GHz: 12.5 dBm
Output Power
(Max.)
yyBecause band channel used by the country could be different, the user can not change or adjust
the operating frequency and this product is set for the regional frequency table.
yyThis device should be installed and operated with minimum distance 20 cm between the device and your body.
And this phrase is for the general statement for consideration of user environment.
HDMI/DVI-DTV Supported Mode
HDMI/DVI-PC Supported Mode
Resolution
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
59.94
60
640 x 350
31.468
70.09
720 x 400
31.469
70.08
720 x 576
31.25
15.625
50
640 x 480
31.469
59.94
60.31
1280 x 720
37.5
44.96
45
50
59.94
60
33.72
33.75
28.125
26.97
27
33.716
33.75
56.25
67.43
67.5
59.94
60
50
23.97
24
29.976
30.00
50
59.94
60
Resolution
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
720 x 480
31.469
31.5
1920 x 1080
800 x 600
37.879
1024 x 768
48.363
60.00
1152 x 864
54.348
60.053
1280 x 1024
63.981
60.020
1360 x 768
47.712
60.015
1920 x 1080
(HDMI-PC)
67.5
60.00
28 IR CODES
ENG
ENGLISH
IR CODES
*This feature is not available for all models.
Code (Hexa)
Function
08
(POWER)
Note
Remote control Button (Power On/Off)
95
ENERGY SAVING
Remote control Button
30
AV MODE
Remote control Button
0B
INPUT
Remote control Button
79
RATIO
Remote control Button
0B
INPUT
Remote control Button
F0
TV/RAD
Remote control Button
10-19
Number Key 0-9
Remote control Button
53
LIST
Remote control Button
1A
Q.VIEW
Remote control Button
02
+
Remote control Button
03
-
Remote control Button
1E
FAV
Remote control Button
79
RATIO
Remote control Button
09
MUTE
Remote control Button
00
Pꕌ
Remote control Button
01
Pꕍ
Remote control Button
AB
GUIDE
Remote control Button
0C
PORTAL
Remote control Button
AA
INFO
Remote control Button
45
Q.MENU
Remote control Button
AA
INFO
Remote control Button
40
^
Remote control Button
41
v
Remote control Button
07
<
Remote control Button
06
>
Remote control Button
44
OK
Remote control Button
43
HOME
28
(BACK)
Remote control Button
Remote control Button
5B
EXIT
Remote control Button
72
RED
Remote control Button
71
GREEN
Remote control Button
63
YELLOW
Remote control Button
61
BLUE
Remote control Button
20
TEXT
Remote control Button
21
T.OPT(T.Option)
Remote control Button
B1
n
Remote control Button
B0
►
Remote control Button
BA
yy
Remote control Button
8E
►►
Remote control Button
8F
◄◄
Remote control Button
45
Q.MENU
Remote control Button
91
AD
Remote control Button
7E
SIMPLINK
Remote control Button
E8
ALARM
Remote control Button
DC
3D
Remote control Button
7C
SMART
Remote control Button
EXTERNAL CONTROL DEVICE SETUP 29
RS-232C Setup
ENGLISH
ENG
EXTERNAL CONTROL DEVICE SETUP
RS-232C Configurations
Connect the RS-232C (serial port) input jack to an
external control device (such as a computer or an A/V
control system) to control the product’s functions externally.
Connect the serial port of the control device to the RS232C jack on the product back panel.
*Note: RS-232C connection cables are not supplied
RXD
with the product.
TXD
GND
RS-232C IN
(CONTROL & SERVICE)
7-Wire Configurations
(Standard RS-232C cable)
PC
TV
2
3
TXD
3
2
RXD
5
5
GND
DTR
4
6
DSR
DSR
6
4
DTR
RTS
7
8
CTS
CTS
8
7
RTS
D-Sub 9
D-Sub 9
(*Not Provided)
3-Wire Configurations
(Not standard)
Type of Connector:
D-Sub 9-Pin Male
1
5
RXD
TXD
GND
DTR
DSR
RTS
CTS
PC
TV
2
3
5
4
6
7
8
3
2
5
6
4
7
8
D-Sub 9
D-Sub 9
TXD
RXD
GND
DTR
DSR
RTS
CTS
Set ID
6
No.
9
Pin name
1
3.5V
2
RXD (Receive data)
3
TXD (Transmit data)
4
IR OUT from TV
5
GND
6
No Connection
7
No Connection (5V available in some models)
8
No Connection
9
No Connection (12V available in some models)
Set ID number. "Real Data Mapping".
1
Press SETTINGS or HOME to access the
main menus.
2
Press the Navigation buttons to scroll to
OPTION and press OK.
3
Press the Navigation buttons to scroll to Set
ID and press OK.
4
Scroll left or right to select a set ID number
and select Close. The adjustment range is
1-99.
5
When you are finished, press EXIT.
30 EXTERNAL CONTROL DEVICE SETUP
ENG
ENGLISH
Communication Parameters
yy Baud rate: 9600 bps (UART)
yy Data length: 8 bits
yy Parity : None
yy Stop bit: 1 bit
yy Communication code: ASCII code
yy Use a crossed (reverse) cable.
Command Reference List
(Depending on Model)
COMMAND1
COMMAND2
DATA
(Hexadecimal)
COMMAND1 COMMAND2
DATA
(Hexadecimal)
01. Power
k
a
00 to 01
02. Aspect Ratio
k
c
(See p. 32)
13. Balance
k
t
00 to 64
14. Colour
Temperature
x
u
00 to 64
03. Screen Mute
k
d
(See p. 32)
15. Energy
Saving
j
q
00 to 05
j
u
01
04. Volume Mute
k
e
00 to 01
16. Auto
Configuration
05. Volume
Control
k
f
00 to 64
17. Equalize
j
V
(See p. 34)
06. Contrast
k
g
00 to 64
18. Tune
Command
m
a
(See p. 34)
07. Brightness
k
h
00 to 64
19. Programme
Add/Skip
m
b
00 to 01
08. Colour
k
i
00 to 64
20. Key
m
c
(See p. 28)
09. Tint
k
j
00 to 64
21. Control Back
Light
m
g
00 to 64
10. Sharpness
k
k
00 to 32
22. Input select
(Main)
x
b
(See p. 35)
11. OSD Select
k
l
00 to 01
12. Remote
Control
Lock Mode
k
m
00 to 01
* Note : During USB operations such as DivX or EMF, all commands except Power(ka) and Key(mc) are
not executed and treated as NG.
EXTERNAL CONTROL DEVICE SETUP 31
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
[Command 1]
[Command 2]
[Set ID]
: First command to control the TV.(j, k, m or x)
: Second command to control the TV.
: You can adjust the set ID to choose desired monitor ID number in option menu.
Adjustment range is 1 to 99. When selecting Set ID ‘0’, every connected set is controlled.
Set ID is indicated as decimal (1 to 99) on menu and as Hexa decimal (0x0 to 0x63)
on transmission/receiving protocol.
[DATA] : To transmit command data. Transmit ‘FF’ data to read status of command.
[Cr] : Carriage Return
ASCII code ‘0x0D’
[ ]
: ASCII code ‘space (0x20)’
OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
* The set transmits ACK (acknowledgement) based on this format when receiving normal data. At this time,
if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the
data of the PC computer.
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]
* The set transmits ACK (acknowledgement) based on this format when receiving abnormal data from
non-viable functions or communication errors.
Data 00: Illegal Code
ENGLISH
ENG
Transmission / Receiving Protocol
32 EXTERNAL CONTROL DEVICE SETUP
ENG
ENGLISH
01. Power (Command: k a)
04. Volume Mute (Command: k e)
▶ To control Power On/Off of the set.
▶ To control volume mute on/off.
You can also adjust mute using the MUTE button
on remote control.
Transmission[k][a][ ][Set ID][ ][Data][Cr]
Data
00 : Power Off
01 : Power On
Ack [a][ ][Set ID][ ][OK/NG][Data][x]
▶ To show Power On/Off.
Transmission [k][a][ ][Set ID][ ][FF][Cr]
Transmission [k][e][ ][Set ID][ ][Data][Cr]
Data 00 : Volume mute on (Volume off)
01 : Volume mute off (Volume on)
Ack [e][ ][Set ID][ ][OK/NG][Data][x]
Ack [a][ ][Set ID][ ][OK/NG][Data][x]
* Similarly, if other functions transmit ‘0xFF’ data based
on this format, Acknowledgement data feed back
presents status about each function.
* OK Ack., Error Ack. and other message may display on
the screen when TV is power On.
05. Volume Control (Command: k f)
▶ To adjust volume.
You can also adjust volume with the volume buttons
on remote control.
Transmission [k][f][ ][Set ID][ ][Data][Cr]
02. Aspect Ratio (Command: k c)
(Main Picture Size)
▶ To adjust the screen format. (Main picture format)
You can also adjust the screen format using the Aspect Ratio
in the Q.MENU. or PICTURE menu.
Transmission [k][c][ ][Set ID][ ][Data][Cr]
Data 01 : Normal screen (4:3)
02 : Wide screen
(16:9)
04 : Zoom
06 : Original
07 : 14:9
09 : Just Scan
0B : Full Wide
10 to 1F : Cinema Zoom 1 to 16
Ack [c][ ][Set ID][ ][OK/NG][Data][x]
* Using the PC input, you select either 16:9 or 4:3 screen
aspect ratio.
* In DTV/HDMI (1080i 50 Hz / 60 Hz, 720p 50Hz / 60 Hz,
1080p 24 Hz / 30 Hz / 50 Hz / 60 Hz), Component( 720p,
1080i, 1080p 50 Hz / 60 Hz) mode, Just Scan is available.
* Full Wide is supported only for Digital, Analogue, AV.
03. Screen Mute (Command: k d)
▶ To select screen mute on/off.
Data Min : 00 to Max : 64
* Refer to ‘Real data mapping’. See p. 35.
Ack [f][ ][Set ID][ ][OK/NG][Data][x]
06. Contrast (Command: k g)
▶ To adjust screen contrast.
You can also adjust contrast in the PICTURE menu.
Transmission [k][g][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
* Refer to ‘Real data mapping’. See p. 35.
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
07. Brightness (Command: k h)
▶ To adjust screen brightness.
You can also adjust brightness in the PICTURE menu.
Transmission [k][h][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
* Refer to ‘Real data mapping’. See p. 35.
Ack [h][ ][Set ID][ ][OK/NG][Data][x]
Transmission [k][d][ ][Set ID][ ][Data][Cr]
Data 00 : Screen mute off (Picture on)
Video mute off
01 : Screen mute on (Picture off)
10 : Video mute on
Ack [d][ ][Set ID][ ][OK/NG][Data][x]
* In case of video mute on only, TV will display On Screen
Display(OSD). But, in case of Screen mute on, TV will not
display OSD.
08. Colour (Command: k i)
▶ To adjust the screen colour.
You can also adjust colour in the PICTURE menu.
Transmission [k][i][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
* Refer to ‘Real data mapping’. See p. 35.
Ack [i][ ][Set ID][ ][OK/NG][Data][x]
EXTERNAL CONTROL DEVICE SETUP 33
13. Balance (Command: k t)
▶ To adjust the screen tint.
You can also adjust tint in the PICTURE menu.
▶ To adjust balance.
You can also adjust balance in the AUDIO menu.
Transmission [k][j][ ][Set ID][ ][Data][Cr]
Data Red : 00 to Green : 64
* Refer to ‘Real data mapping’. See p. 35.
Transmission [k][t][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
* Refer to ‘Real data mapping’. See p. 35.
Ack [j][ ][Set ID][ ][OK/NG][Data][x]
Ack [t][ ][Set ID][ ][OK/NG][Data][x]
10. Sharpness (Command: k k)
▶ To adjust the screen sharpness.
You can also adjust sharpness in the PICTURE menu.
Transmission [k][k][ ][Set ID][ ][Data][Cr]
14. Colour Temperature (Command: x u)
▶ To adjust colour temperature. You can also adjust
Colour Temperature in the PICTURE menu.
Data Min : 00 to Max : 32
* Refer to ‘Real data mapping’. See p. 35.
Transmission [x][u][ ][Set ID][ ][Data][Cr]
Ack [k][ ][Set ID][ ][OK/NG][Data][x]
Data Min : 00 to Max : 64
* Refer to ‘Real data mapping’. See p. 35.
11. OSD Select (Command: k l)
▶ To select OSD (On Screen Display) on/off when
controlling remotely.
Ack [u][ ][Set ID][ ][OK/NG][Data][x]
Transmission [k][l][ ][Set ID][ ][Data][Cr]
Data 00 : OSD off
01 : OSD on
Ack [l][ ][Set ID][ ][OK/NG][Data][x]
15. Energy Saving (Command: j q)
▶ To reduce the power consumption of the TV.
You can also adjust Energy Saving in PICTURE menu.
Transmission [j][q][ ][Set ID][ ][Data][Cr]
12. Remote control lock mode (Command: k m)
Power Saving
Function
▶ To lock the front panel controls on the monitor and
remote control.
Level
7
6
5
4
01 : Lock on
0
0
0
0
Ack [m][ ][Set ID][ ][OK/NG][Data][x]
0
0
0
0
0
0
Transmission [k][m][ ][Set ID][ ][Data][Cr]
Data 00 : Lock off
* If you are not using the remote control, use this mode.
When main power is on/off, external control lock is
released.
* In the standby mode, if key lock is on, TV will not turn
on by power on key of IR & Local Key.
Description
3
2
1
0
Low
Power
0
0
0
0
Off
0
Low
Power
0
0
0
1
Minimum
0
0
Low
Power
0
0
1
0
Medium
0
0
0
Low
Power
0
0
1
1
Maximum
0
0
0
0
Low
Power
0
1
0
1
Screen
Off
0
0
0
0
Low
Power
0
1
0
0
Auto
▶ 'Auto' is available in TV that supports 'Intelligent Sensor'
Ack [q][ ][Set ID][ ][OK/NG][Data][x]
ENGLISH
ENG
09. Tint (Command: k j)
34 EXTERNAL CONTROL DEVICE SETUP
ENG
ENGLISH
18. Tune Command (Command: m a)
16. Auto Configure(Command: j u)
(Only RGB support model)
▶ To adjust picture position and minimize image shaking
automatically. It works only in RGB (PC) mode.
Transmission [j][u][ ][Set ID][ ][Data][Cr]
Ack [u][ ][Set ID][ ][OK/NG][Data][x]
17. Equalize(Command: j v)
[Cable]
0x80 : Analog Main
0x90 : DTV Main
0xA0 : Radio
▶ To adjust equalize.
Transmission [j][v][ ][Set ID][ ][Data][Cr]
MSB
LSB
0
0
0
Transmission [m][a][ ][Set ID][ ][Data0][ ][Data1][ ][Data2][Cr]
Data00 : High channel data
Data01 : Low channel data
ex. No. 47 -> 00 2F (2FH)
No. 394 -> 01 8A (18AH),
DTV No. 0 -> Don’t care
Data02 : [Antena]
0x00 : Analog Main
0x10 : DTV Main
0x20 : Radio
Data 01: To set
0
▶ Select channel to following physical number.
0
0
Frequency
0
0
Ack [a][ ][Set ID][ ][OK/NG][Data][x]
Data
7
6
5
Frequency
4
3
2
1
0
Step
0
0
0
1’st Band
0
0
0
0
0
0(decimal)
0
0
1
2’nd Band
0
0
0
0
1
1(decimal)
0
1
0
3’rd Band
...
...
...
...
...
...
0
1
1
4’th Band
1
0
1
0
0
20(decimal)
1
0
0
5’th Band
1
0
1
0
1
21(decimal)
Ack [v][ ][Set ID][ ][OK/NG][Data][x]
Channel data range
Analogue - Min: 00 to Max: 63 (0 to 99)
Digital - Min: 00 to Max: 3E7 (0 to 999)
Data Min: 00 to Max: 7DH
19. Programme Add/Skip(Command: m b)
▶ To set skip status for the current Programme.
Transmission [m][b][ ][Set ID][ ][Data][Cr]
Data 00 : Skip
01 : Add
Ack [b][ ][Set ID][ ][OK/NG][Data][x]
20. Key(Command: m c)
▶ To send IR remote key code.
Transmission [m][c][ ][Set ID][ ][Data][Cr]
Data Key code - See p. 28.
Ack [c][ ][Set ID][ ][OK/NG][Data][x]
21. Control Back Light(Command: m g)
▶ To control the back light.
Transmission [m][g][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
EXTERNAL CONTROL DEVICE SETUP 35
ENGLISH
ENG
22. Input select (Command: x b)
(Main Picture Input)
▶ To select input source for main picture.
Transmission [x][b][ ][Set ID][ ][Data][Cr]
Data Structure
MSB
0
LSB
0
0
0
0
External Input
0
0
Input Number
External Input
Data
0
0
0
0
DTV
0
0
0
1
Analogue
0
0
1
0
AV
0
1
0
0
Component
0
1
1
0
RGB
0
1
1
1
1
0
0
0
1
0
0
1
1
0
1
0
Input Number
HDMI
Data
0
0
0
0
Input1
0
0
0
1
Input2
0
0
1
0
Input3
0
0
1
1
Input4
Ack [b][ ][Set ID][ ][OK/NG][Data][x]
* Real data mapping
00 :
Step 0
A:
Step 10 (Set ID 10)
F:
Step 15 (Set ID 15)
10 :
Step 16 (Set ID 16)
64 :
Step 100
6E :
Step 110
73 :
Step 115
74 :
Step 116
CF :
Step 199
FE :
Step 254
FF :
Step 255
0
Record the model number and serial number of
the TV.
Refer to the label on the back cover and quote
this information to your dealer when requiring
any service.
MODEL
SERIAL