User’s Guide
Notations Used in This Guide
• Safety indications
The documentation and the projector use graphical symbols to show how to use the projector safely.
The indications and their meaning are as follows. Make sure you understand them properly before reading the guide.
Warning
This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect handling.
Caution
This symbol indicates information that, if ignored, could possibly result in personal injury or physical damage due to incorrect handling.
• General information indications
Attention
a
Indicates procedures which may result in damage or injury if sufficient care is not taken.
Indicates additional information and points which may be useful to know regarding a topic.
s
Indicates a page where detailed information regarding a topic can be found.
g
Indicates that an explanation of the underlined word or words in front of this symbol appears in the glossary of terms. See the "Glossary"
section of the "Appendices".
s "Glossary" p.159
[Name]
Menu Name
Indicates the name of the buttons on the remote control or the control panel.
Example: [Esc] button
Indicates Configuration menu items.
Example:
Select Brightness from Image.
Image - Brightness
Contents
3
Notations Used in This Guide . . . . . . . . . . . . . . . . . . . . . . . . 2
Preparing the Projector
Installing the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Introduction
Installation Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Projector Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Projection Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Enabling projection from a short distance . . . . . . . . . . . . . . . . . . . . . . . .
Drawing function (EB-485Wi/EB-480i/EB-475Wi only) . . . . . . . . . . . . . . . .
Easy writing on a whiteboard or blackboard using the pattern function . . . .
Connecting with a USB cable and projecting (USB Display) . . . . . . . . . . . .
Connecting to a network and projecting images from the computer's screen
.....................................................
Enhanced security functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Optional Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Enlarge and project your files with the Document Camera . . . . . . . . . . . . .
Easy connection to a computer with Quick Wireless . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
8
8
8
8
8
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
8
8
8
8
9
Part Names and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Front/Top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Attaching the feet (Only models with feet supplied) . . . . . . . . . . . . . . . .
Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacing the remote control batteries . . . . . . . . . . . . . . . . . . . . . . . . .
Remote control operating range . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Easy Interactive Pen (EB-485Wi/EB-480i/EB-475Wi Only) . . . . . . . . . . . . . . .
Replacing the battery for the Easy Interactive Pen . . . . . . . . . . . . . . . . .
Replacing the tip of the Easy Interactive Pen . . . . . . . . . . . . . . . . . . . . .
Pen Tray (EB-485Wi/EB-480i/EB-475Wi Only) . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
10
11
12
13
14
15
16
18
19
20
20
21
22
Connecting Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Connecting a Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting Image Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting USB Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting a microphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting External Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting a LAN Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the Optional Wireless LAN Unit . . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
26
28
31
33
34
36
37
Basic Usage
Projecting images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
From Installation to Projection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automatically Detect Input Signals and Change the Projected Image (Source Search)
... ....... ......... ... ....... ......... ... ....... ..........
Switching to the Target Image Using the Remote Control . . . . . . . . . . . . . . . . . .
Projecting with USB Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting for the first time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Uninstalling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
39
40
41
41
41
42
43
Adjusting Projected Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Correcting Keystone Distortion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
H/V-Keystone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Quick Corner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting the Image Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting the Position of the Image (Image Shift) . . . . . . . . . . . . . . . . . . . . . .
Adjusting the Vertical Position of the Image (Models Supplied with the Feet Only)
... ....... ......... ... ....... ......... ... ....... ........
Raising the height of the image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lowering the height of the image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
45
45
46
48
48
. . 49
. . 49
. . 50
Contents
4
Adjusting the Horizontal Position of the Image (Models Supplied with the Feet Only)
........ ......... .......... ......... .......... ......... ...
Correcting the Focus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting the Projection Quality (Selecting Color Mode) . . . . . . . . . . . . . . . . . . .
Setting Auto Iris . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing the Aspect Ratio of the Projected Image . . . . . . . . . . . . . . . . . . . . . . .
Changing methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing the aspect mode (EB-485Wi/EB-485W/EB-475Wi/EB-475W only) . . . . .
Changing the aspect mode (EB-480i/EB-480/EB-470 only) . . . . . . . . . . . . . . . .
50
50
50
51
52
52
53
53
54
Useful Functions
Easy Interactive Function (EB-485Wi/EB-480i/EB-475Wi only)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Introducing the Easy Interactive Function . . . . . . . . . . . . . . . . . . . . . . . . . .
Drawing with the projector's built-in function . . . . . . . . . . . . . . . . . . . . .
Operating as a mouse and drawing by connecting to a computer (Computer
Interactive) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Drawing with the Projector's Built-in Function . . . . . . . . . . . . . . . . . . . . . . .
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Calibrating the pen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Toolbar functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating as a mouse and drawing by connecting to a computer (Computer
Interactive) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Install Easy Interactive Driver (Mac OS X only) . . . . . . . . . . . . . . . . . . . . .
Operating the computer with a pen instead of a mouse . . . . . . . . . . . . . .
Allowing two people to use pens at the same time . . . . . . . . . . . . . . . . . .
Adjusting the pen operation area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 57
. . . 57
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
57
58
58
59
62
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
64
64
65
65
66
Projection Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Hiding the Image and Sound Temporarily (A/V Mute) . . . . . . . . . . . . . .
Freezing the Image (Freeze) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pointer Function (Pointer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Enlarging Part of the Image (E-Zoom) . . . . . . . . . . . . . . . . . . . . . . . . .
Using the Remote Control to Operate the Mouse Pointer (Wireless Mouse)
Saving a User's Logo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.. .. . .
. .. .. .
......
......
. . . . .
. . ... .
.
.
.
.
.
.
67
67
68
69
70
71
Saving User Pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Projecting Without a Computer (Slideshow) . . . . . . . . . . . . . . . . . . . . . .
Specifications for files that can be projected using Slideshow . . . . . . . . .
Slideshow examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Slideshow operating methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Projecting the selected image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Projecting image files in a folder in sequence (Slideshow) . . . . . . . . . . .
Image file display settings and Slideshow operation settings . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
73
74
74
75
75
77
78
78
Security Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Managing Users (Password Protect) . . . . . . . . . . . . . . . . . . . . . . . . . . .
Kinds of Password Protect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting Password Protect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Entering the Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Restricting Operation (Control Panel Lock) . . . . . . . . . . . . . . . . . . . . . .
Anti-Theft Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the wire lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
80
80
80
81
82
83
83
Monitoring and Controlling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
About EasyMP Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing Settings Using a Web Browser (Web Control) . . . . . . . . . . . . . . .
Projector setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Displaying the Web Control screen . . . . . . . . . . . . . . . . . . . . . . . . . .
Displaying the Web Remote screen . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the Mail Notification Function to Report Problems . . . . . . . . . . . . . .
Reading Error Notification Mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Management Using SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ESC/VP21 Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Command list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cable layouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About PJLink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About Crestron RoomView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating a projector from your computer . . . . . . . . . . . . . . . . . . . . .
®
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
84
84
84
85
85
87
87
87
88
88
88
89
90
90
Contents
5
Configuration Menu
Using the Configuration Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
List of Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Configuration Menu Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Network menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Image Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Signal Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Settings Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Extended Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Network Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Notes on operating the Network menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Soft keyboard operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Basic menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Wireless LAN menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Security menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Wired LAN menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Mail menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Others menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Reset menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Info Menu (Display Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Reset Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Troubleshooting
Using the Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
The message No Signal is displayed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Images are fuzzy, out of focus, or distorted . . . . . . . . . . . . . . . . . . . . . . . . .
Interference or distortion appear in images . . . . . . . . . . . . . . . . . . . . . . . . .
The mouse cursor flickers (only when projecting USB Display) . . . . . . . . . . . .
The image is truncated (large) or small, or the aspect is not suitable . . . . . . . .
Image colors are not right . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Images appear dark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Problems when Projection Starts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The projector does not turn on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Problems Relating to the Easy Interactive Function . . . . . . . . . . . . . . . . . . . . . .
Cannot the projector's built-in drawing function . . . . . . . . . . . . . . . . . . . . .
Cannot operate as a mouse and draw by connecting to a computer . . . . . . . .
The message An error occurred in the Easy Interactive Function. is displayed
........................................................
The Easy Interactive Pen does not work . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The reaction time for the Easy Interactive Pen is slow (only when projecting USB
Display) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The dot does not move to the next position . . . . . . . . . . . . . . . . . . . . . . . . .
The dot moves automatically . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Other Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
No sound can be heard or the sound is faint . . . . . . . . . . . . . . . . . . . . . . . .
No sound can be heard from the microphone . . . . . . . . . . . . . . . . . . . . . . .
The remote control does not work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I want to change the language for messages and menus . . . . . . . . . . . . . . . .
Mail is not received even if an error occurs with the projector . . . . . . . . . . . . .
Image file names are not displayed correctly in Slideshow . . . . . . . . . . . . . . .
Cannot change settings using a web browser . . . . . . . . . . . . . . . . . . . . . . .
124
125
126
126
126
127
128
128
128
129
129
130
130
130
131
131
131
132
132
132
133
133
134
134
134
About Event ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
Problem Solving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Reading the Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
When the Indicators Provide No Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Problems Relating to Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
No images appear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Moving images are not displayed (only the moving image portion turns black)
........................................................
Projection stops automatically . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The message Not supported is displayed . . . . . . . . . . . . . . . . . . . . . . . . . . .
118
122
123
123
124
124
124
Maintenance
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Cleaning the Projector's Surface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cleaning the Projection Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cleaning the Obstacle Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cleaning the Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
137
137
137
138
Contents
6
Replacing Consumables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
Replacing the Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lamp replacement period . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
How to replace the lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Resetting the lamp hours . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacing the Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Air filter replacement period . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
How to replace the air filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
139
139
140
142
142
142
142
Appendix
Optional Accessories and Consumables . . . . . . . . . . . . . . . . . . . . 146
Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Consumables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Screen Size and Projection Distance . . . . . . . . . . . . . . . . . . . . . . . . 147
Projection Distance (For EB-485Wi/EB-485W/EB-475Wi/EB-475W) . . . . . . . . . . . . 147
Projection Distance (For EB-480i/EB-480/EB-470) . . . . . . . . . . . . . . . . . . . . . . . 148
Supported Monitor Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
Supported Resolutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Computer signals (analog RGB) . . . . . . . . . . . . . . . . . . . . . . . . .
Component Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Composite video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input signal from the HDMI port . . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
150
150
150
150
150
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
Projector General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
Appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
General Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
Wireless Telegraphy Act Regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
About Notations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
General Notice: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
Introduction
This chapter explains the projector's features and the part names.
Projector Features
Projection Functions
Enabling projection from a short distance
You can project large images from a short distance without having to move
the projector away from the screen. By mounting the projector on a ceiling
or wall, you can minimize shadows cast on the screen even when you are
standing near it and avoid being dazzled by the projected light.
s "Screen Size and Projection Distance" p.147
Drawing function (EB-485Wi/EB-480i/EB-475Wi only)
You can write characters and draw figures on the projected screen using the
electronic pen (Easy Interactive Pen). You can also draw on a computer
screen from the projected screen by using the Easy Interactive Tools
software supplied.
s "Easy Interactive Function (EB-485Wi/EB-480i/EB-475Wi only)"
p.57
Easy writing on a whiteboard or blackboard using the pattern
function
You can project ruled lines and grid patterns. This is useful when drawing
diagrams on a whiteboard or blackboard.
s Settings - Pattern p.101
Connecting with a USB cable and projecting (USB Display)
8
Connecting to a network and projecting images from the
computer's screen
You can connect the projector to a computer on a network and project the
computer's screen using the supplied EasyMP Network Projection
(application software).
s EasyMP Network Projection Operation Guide
Enhanced security functions
• Password Protect to restrict and manage users
By setting a password you can restrict who can use the projector.
s "Managing Users (Password Protect)" p.80
• Control Panel Lock restricts button operation on the control panel
You can use this to prevent people changing projector settings without
permission at events, in schools, and so on.
s "Restricting Operation (Control Panel Lock)" p.82
• Equipped with various anti-theft devices
The projector is equipped with the following types of anti-theft security
devices.
• Security slot
• Security cable installation point
s "Anti-Theft Lock" p.83
Optional Functions
Enlarge and project your files with the Document Camera
By simply connecting the supplied or a commercially available USB cable,
you can project images from a computer's screen without a computer
cable.
You can project paper documents and objects using the optional Document
Camera. Image focus is automatically adjusted using the auto focus
function. You can also enlarge images using digital zoom.
s "Projecting with USB Display" p.41
s "Optional Accessories" p.146
Projector Features
Easy connection to a computer with Quick Wireless
By simply connecting the optional Quick Wireless Connection USB Key to
a computer, you can project the computer's screen. (Windows computers
only)
s "Optional Accessories" p.146
9
Part Names and Functions
10
Name
Front/Top
Name
Function
A Remote receiver
Receives signals from the remote control.
B Lamp cover
Open when replacing the projector's lamp.
s "Replacing the Lamp" p.139
C Lamp cover fixing
screw
Screw to fix the lamp cover in place.
s "Replacing the Lamp" p.139
D Air exhaust vent
Exhaust vent for air used to cool the projector internally.
Caution
While projecting, do not put your face or hands
near the air exhaust vent, and do not place objects
that may become warped or damaged by heat near
the vent.
E Cable cover fixing
screws
Screws to fix the cable cover in place.
Function
F Cable cover
Open by loosening both of the screws when connecting to
an input port or installing the wireless LAN unit.
G Control panel
Operates the projector.
s "Control Panel" p.15
H Speaker
Outputs audio.
Part Names and Functions
11
Side
Name
Function
C Wireless LAN indicator
Indicates the access status to the optional wireless LAN
unit.
D Easy Interactive
Function receiver
(EB-485Wi/EB-480i/
EB-475Wi only)
Receives signals from the Easy Interactive Pen.
s "Easy Interactive Function (EB-485Wi/EB-480i/
EB-475Wi only)" p.57
E Obstacle sensor
Detects obstacles that are interfering with the projection
area.
s "Cleaning the Obstacle Sensor" p.137
F Remote receiver
Receives signals from the remote control.
G Projection window
Projects images.
Warning
• Do not look into the projection window while
projecting.
• Do not place any objects or put your hand near
the projection window. This area is dangerous
as it reaches high temperatures due to the con‐
centrated projection light.
Name
Function
A Air filter cover
open/close lever
Opens and closes the air filter cover.
B Security cable
installation point
Pass a commercially available wire lock through here and
lock it in place.
s "Installing the wire lock" p.83
H Security slot
The security slot is compatible with the Microsaver
Security System manufactured by Kensington.
s "Anti-Theft Lock" p.83
I Air filter cover
Open when changing the air filter or operating the focus
lever.
J Air intake vent
(air filter)
Takes in air to cool the projector internally.
s "Cleaning the Air Filter" p.138
s "Replacing the Air Filter" p.142
K Focus lever
Adjusts the image focus.
Open the air filter cover to operate.
Part Names and Functions
12
Name
Interface
The following ports are available under the cable cover.
Name
Function
G LAN port
Connects a LAN cable to connect to a network.
H USB-A port
• Connects a USB memory device or a digital camera, and
projects images as a Slideshow.
s "Projecting Without a Computer (Slideshow)"
p.74
• Connects the optional Document Camera.
I USB-B port
• Connects the projector to a computer via the supplied or
a commercially available USB cable, and projects the
images on the computer.
s "Projecting with USB Display" p.41
• Connects the projector to a computer via the supplied or
a commercially available USB cable to use the Wireless
Mouse function.
s "Using the Remote Control to Operate the
Mouse Pointer (Wireless Mouse)" p.70
• Connects the projector to a computer via the supplied or
a commercially available USB cable to use the Easy
Interactive Pen as a mouse or as a pen to draw on the
projected screen. (EB-485Wi/EB-480i/EB-475Wi only)
s "Operating as a mouse and drawing by
connecting to a computer (Computer Interactive)"
p.57
Function
A Wireless LAN unit
installation section
Install the optional Wireless LAN unit here.
s "Installing the Optional Wireless LAN Unit" p.37
B Audio1 port
Inputs audio from equipment connected to the
Computer1 port.
J HDMI port
C Audio2 port
• Inputs audio from equipment connected to the
Computer2 port.
• Inputs audio from other devices when projecting
images from the device connected to the USB-A port.
Inputs video signals from HDMI compatible video
equipment and computers. This projector is compatible
with HDCPg.
s "Connecting Equipment" p.26
K RS-232C port
When controlling the projector from a computer, connect
it to the computer with an RS-232C cable. This port is for
control use and should not normally be used.
s "ESC/VP21 Commands" p.88
D Computer1 port
Inputs image signals from a computer and component
video signals from other video sources.
E Computer2 port
Inputs image signals from a computer and component
video signals from other video sources.
L Audio Out port
F Monitor Out port
Outputs analog RGB signals input from the Computer1
port to an external monitor. You cannot output signals
input from other ports or component video signals.
Outputs audio from the currently projected image or the
Mic port to an external speaker.
M Power inlet
Connects the power cord to the projector.
s "From Installation to Projection" p.39
Part Names and Functions
Name
13
Function
N Audio-L/R port
Inputs audio from equipment connected to the S-Video
port or the Video port.
O Video port
Inputs composite video signals from video sources.
P S-Video port
For S-video signals from video sources.
Q Mic port
Inputs audio from the microphone.
s "Connecting a microphone" p.33
Base
Name
Function
A Ceiling mount fixing
points (five points)
Attach the optional Ceiling Mount here when suspending
the projector from a ceiling.
s "Installing the Projector" p.24
s "Optional Accessories" p.146
B Security cable
installation point
Pass a commercially available wire lock through here and
lock it in place.
s "Installing the wire lock" p.83
Part Names and Functions
14
Name
Function
C Rear foot fixing points
(two points)
Attach the feet when using the projector on a surface such
as a desk. (Only models with feet supplied)
s "Attaching the feet (Only models with feet supplied)"
p.14
D Wall mount fixing
points (four points)
Attach the setting plate when mounting on a wall. (Only
models with setting plate supplied)
s Installation Guide
s "Optional Accessories" p.146
E Front foot fixing point
Attach the foot with a spacer when using the projector on a
surface such as a desk. (Only models with feet supplied)
s "Attaching the feet (Only models with feet supplied)"
p.14
Attaching the feet (Only models with feet supplied)
Insert the feet into the foot fixing points.
A Insert the foot with the spacer into the front foot fixing point.
B Insert the rear feet (x2) into the foot fixing points.
a
You can install this projector vertically on a desk.
s "Installation Methods" p.24
Part Names and Functions
15
Name
Control Panel
Function
D [w][v] button
• Displays the Keystone screen.
s "H/V-Keystone" p.45
• If pressed when the Configuration menu or the Help
screen is displayed, these buttons select menu items and
setting values.
s "Using the Configuration Menu" p.95
s "Using the Help" p.117
E [Help] button
Displays and closes the help screen which shows you how
to deal with problems if they occur.
s "Using the Help" p.117
F [Esc] button
• Stops the current function.
• If pressed when the Configuration menu is displayed, it
moves to the previous menu level.
s "Using the Configuration Menu" p.95
G [Tele]/[Wide] buttons
Name
Function
A Status indicators
Indicates the projector's status using color, and by being lit
or flashing.
s "Reading the Indicators" p.118
B [Source Search]
button
Switches to the image from the input port where video
signals are being input.
s "Automatically Detect Input Signals and Change the
Projected Image (Source Search)" p.40
C [Enter] button
[ ]
• When the Configuration menu or the Help screen is
displayed, it accepts and enters the current selection and
moves to the next level.
• If pressed while projecting analog RGB signals from
Computer1 port or Computer2 port, you can
automatically optimize Tracking, Sync., and Position.
• Adjusts the size of the projection screen. Press the [Tele]
button to reduce the size of the projection screen and
press the [Wide] button to increase the size of the
projection screen.
• Corrects keystone distortion in the horizontal direction
when the Keystone screen is displayed.
s "H/V-Keystone" p.45
• If pressed when the Configuration menu or the Help
screen is displayed, these buttons select menu items and
setting values.
s "Using the Configuration Menu" p.95
s "Using the Help" p.117
H [Menu] button
Displays and closes the Configuration menu.
s "Using the Configuration Menu" p.95
I [t] button
Turns the projector power on or off.
s "From Installation to Projection" p.39
Part Names and Functions
Remote Control
16
Name
Function
A [t] button
Turns the projector power on or off.
s "From Installation to Projection" p.39
B [Computer] button
Each time you press the button, the input changes between
images from the Computer1 port and the Computer2
port.
C [Video] button
Each time the button is pressed, the image cycles through
the S-Video, Video, and HDMI ports.
D Numeric buttons
• Enter the Password.
s "Setting Password Protect" p.80
• Use this button to enter numbers in Network settings
from the Configuration menu.
E [Auto] button
If pressed while projecting analog RGB signals from
Computer1 port or Computer2 port, you can
automatically optimize Tracking, Sync., and Position.
F [Aspect] button
Each time the button is pressed, the aspect mode changes.
s "Changing the Aspect Ratio of the Projected Image"
p.52
G [Num] button
Hold down this button and press the numeric buttons to
enter passwords and numbers.
s "Setting Password Protect" p.80
H [Menu] button
Displays and closes the Configuration menu.
s "Using the Configuration Menu" p.95
Part Names and Functions
Name
I [
][
][ ][ ]
button
J [
] button
K [User] button
17
Function
• When the Configuration menu or Help screen is
displayed, pressing these buttons selects menu items
and setting values.
s "Using the Configuration Menu" p.95
• When projecting a Slideshow, pressing these buttons
displays the previous/next image, rotates the image, and
so on.
s "Projecting Without a Computer (Slideshow)"
p.74
• During Wireless Mouse function, the mouse pointer
moves in the direction of the button that was pushed.
s "Using the Remote Control to Operate the
Mouse Pointer (Wireless Mouse)" p.70
• When the Configuration menu or the Help screen is
displayed, it accepts and enters the current selection and
moves to the next level.
s "Using the Configuration Menu" p.95
• Acts as a mouse's left button when using the Wireless
Mouse function.
s "Using the Remote Control to Operate the
Mouse Pointer (Wireless Mouse)" p.70
Select any frequently used item from the seven or eight
available Configuration menu items, and assign it to this
button. By pressing the [User] button, the assigned menu
item selection/adjustment screen is displayed, allowing
you to make one-touch settings/adjustments.
s "Settings Menu" p.101
The following item is assigned by default.
• EB-485Wi/EB-480i/EB-475Wi: Auto Calibration
• EB-485W/EB-480/EB-475W/EB-470: Power
Consumption
Name
L [Page] buttons
[[][]]
Function
Changes pages in files such as PowerPoint files when using
the following projection methods.
• When using the Wireless Mouse function
s "Using the Remote Control to Operate the
Mouse Pointer (Wireless Mouse)" p.70
• When using USB Display
s "Projecting with USB Display" p.41
• When connecting to a network
When projecting images using Slideshow, pressing these
buttons displays the previous/next image file.
M [A/V Mute] button
• Turns the video and audio on or off.
s "Hiding the Image and Sound Temporarily (A/V
Mute)" p.67
• You can change the Projection mode as follows by
pressing the button for about five seconds.
FrontWFront/Upside Down
RearWRear/Upside Down
N [E-Zoom] buttons
[z][x]
Enlarges or reduces the image without changing the
projection size.
s "Enlarging Part of the Image (E-Zoom)" p.69
O Strap attachment hole
Allows you to attach a commercially available strap to the
remote control.
P [Help] button
Displays and closes the help screen which shows you how
to deal with problems if they occur.
s "Using the Help" p.117
Q [Freeze] button
Pauses or resumes image playback.
s "Freezing the Image (Freeze)" p.67
R [Volume] buttons
[a][b]
[a] Decreases the volume.
[b] Increases the volume.
s "Adjusting the Volume" p.50
S [Pointer] button
Displays the on-screen pointer.
s "Pointer Function (Pointer)" p.68
Part Names and Functions
Name
T [Esc] button
18
Function
• Stops the current function.
• If pressed when the Configuration menu is displayed, it
moves to the previous level.
s "Using the Configuration Menu" p.95
• Acts as a mouse's right button when using the Wireless
Mouse function.
s "Using the Remote Control to Operate the
Mouse Pointer (Wireless Mouse)" p.70
U [Color Mode] button
V [LAN] button
Each time the button is pressed, the color mode changes.
s "Selecting the Projection Quality (Selecting Color
Mode)" p.51
Changes to the images projected with EasyMP Network
Projection. When projecting using the optional Quick
Wireless Connection USB Key, this button switches to
that image.
W [USB] button
Each time the button is pressed, it cycles through the
following images:
• USB Display
• Images from the device connected to the USB-A port
X [Source Search]
button
Switches to the image from the input port where video
signals are being input.
s "Automatically Detect Input Signals and Change the
Projected Image (Source Search)" p.40
Y Remote control lightemitting area
Outputs remote control signals.
Replacing the remote control batteries
If the remote control becomes unresponsive or inoperable after it has been
used for some time, the batteries may have reached the end of their service
life. When this happens, replace them with new batteries. Obtain two AA
size manganese or alkaline batteries. You cannot use other batteries except
for the AA size manganese or alkaline.
Attention
Make sure you read the following manual before handling the batteries.
s Safety Instructions
a
Remove the battery cover.
b
Replace the old batteries with new batteries.
While pushing the battery cover catch, lift the cover up.
Part Names and Functions
Caution
Check the positions of the (+) and (-) marks inside the battery holder to
ensure the batteries are inserted the correct way.
c
Reattach the battery cover.
Press the battery cover until it clicks into place.
19
Remote control operating range
Part Names and Functions
20
Easy Interactive Pen (EB-485Wi/EB-480i/EB-475Wi
Only)
Name
Function
C Battery indicator
Indicates the remaining battery power when the power is
turned on.
• Turns green for several seconds when the battery is
charged.
• Flashes green for several seconds when the battery is
low.
• Does not light when the battery is exhausted. Change
the battery.
s "Replacing the battery for the Easy Interactive Pen"
p.20
D Slide switch
Switches the Easy Interactive Pen on and off.
When turned on, it takes a few seconds before the Easy
Interactive Pen is operational.
E Battery cover
Open this cover when replacing the battery.
s "Replacing the battery for the Easy Interactive Pen"
p.20
There are two types of Easy Interactive Pens with different colored bottom
sections. You cannot use Easy Interactive Pens with the same colored
bottom sections at the same time.
s "Optional Accessories" p.146
Replacing the battery for the Easy Interactive Pen
Name
A Pen tip button
B Strap attachment hole
Function
• Touch the screen to select an item such as an icon.
• Touch the screen and move to draw on the projected
screen.
• Move over the screen without touching to move the
pointer.
s "Easy Interactive Function (EB-485Wi/EB-480i/
EB-475Wi only)" p.57
s "Optional Accessories" p.146
Allows you to attach a commercially available strap.
The battery indicator on the Easy Interactive Pen lights or flashes when the
power is turned on. Does not light or flash when the battery is exhausted.
When the indicator no longer lights or flashes, replace the battery. Use one
of the following types of battery. Other chargeable batteries cannot be
used.
• AA size
• AA size
• SANYO
*eneloop
®
manganese battery
alkaline manganese battery
eneloop *(HR-3UTG/HR-3UTGA)
is a registered trademark of Sanyo Electronic Co., Ltd.
®
Attention
Make sure you read the following manual before handling batteries.
s Safety Instructions
Part Names and Functions
a
Remove the battery cover.
b
Replace the old battery with a new battery.
21
While pushing the battery cover catch, lift the cover up.
Replacing the tip of the Easy Interactive Pen
Replace the tip of the Easy Interactive Pen when it is worn.
s "Optional Accessories" p.146
a
Turn the tip of the pen to remove it.
b
Turn the new tip to attach it.
Caution
Check the positions of the (+) and (-) marks inside the battery holder to
ensure the battery is inserted the correct way.
c
Replace the battery cover.
Press the battery cover until it clicks into place.
Part Names and Functions
22
Pen Tray (EB-485Wi/EB-480i/EB-475Wi Only)
Name
Function
A Fixing points
Attach the pen tray to a whiteboard or wall.
B Security hole
Pass a commercially available lock through here.
a
It is recommended that the pen tray be tightened with two
commercially available M5 bolts.
Preparing the Projector
This chapter explains how to install the projector and connect projection sources.
Installing the Projector
24
• Project images from in front of
the screen. (Front projection)
Installation Methods
The projector supports the following six different projection methods.
Install the projector according to the installation location.
• Project images from behind a
translucent screen. (Rear projec‐
tion)
Turn the projector off when you are changing the installation method. Turn
the projector back on after changing the installation method.
a
You cannot use the Easy Interactive Function while the Projection
setting is Rear/Upside Down or Rear. (EB-485Wi/EB-480i/EB-475Wi
only)
s "Easy Interactive Function (EB-485Wi/EB-480i/EB-475Wi only)"
p.57
• Mount the projector on a wall
or ceiling and project images
from in front of a screen.
(Front/Upside Down projection)
• Mount the projector on a wall
or ceiling and project images
from behind a translucent
screen. (Rear/Upside Down pro‐
jection)
a
Attach the feet when using the projector on a surface such as a desk.
s "Attaching the feet (Only models with feet supplied)" p.14
• Place the projector vertically and
project images from in front of
the screen. (Front/Upside Down
projection)
• Place the projector vertically and
project images from behind the
screen (Rear/Upside Down pro‐
jection)
Installing the Projector
Warning
• A special method of installation is required when suspending the projector
from a wall or ceiling. If it is not installed correctly, it could fall causing an
accident and injury.
• If you use adhesives on the wall mount plate fixing points or the ceiling
mount fixing points to prevent the screws from loosening, or if you use
things such as lubricants or oils on the projector, the projector case may
crack causing it to fall from its mount. This could cause serious injury to
anyone under the mount and could damage the projector.
When installing or adjusting the mount, do not use adhesives to prevent the
screws from loosening and do not use lubricant or oil and so on.
• Do not cover the projector's air intake vent or air exhaust vent. If either of
the vents are covered, the internal temperature could rise and cause a fire.
a
• When mounting the projector on a wall or ceiling, or placing the
projector vertically, make sure you use the correct tools for the
installation method.
s "Optional Accessories" p.146
• The default Projection setting is Front/Upside Down. You can
change to other Projection settings from the Configuration menu.
s Extended - Projection p.103
• You can change the Projection setting as follows by pressing down
the [A/V Mute] button on the remote control for about five seconds.
FrontWFront/Upside Down
RearWRear/Upside Down
25
Connecting Equipment
26
The port name, location, and connector orientation differ depending on the source being connected.
Connecting a Computer
To project images from a computer, connect the computer using one of the following methods.
A B When using a commercially available computer cable
Connect the computer's display output port to the projector's Computer1 or Computer2 port.
You can output audio from the projector's speaker by connecting the computer's audio output port to the projector's Audio1 or Audio2 port using a commercially available
audio cable.
When
using the supplied or a commercially available USB cable
C
Connect the computer's USB port to the projector's USB-B port.
You can send the audio with the projected image.
When using a commercially available HDMI cable
D
Connect the computer's HDMI port to the projector's HDMI port.
You can send the audio with the projected image.
Connecting Equipment
a
27
• If it is difficult to connect the computer cable to the projector's Computer2 port, try disconnecting the cable from the Computer1 port, connecting the cable to
the Computer2 port, and then reconnecting the cable to the Computer1 port.
• You can switch the audio input by using Audio Input.
s Extended - Operation - Audio Input p.103
• You can use a USB cable to connect the projector to a computer to project images from the computer. This function is called USB Display.
s "Projecting with USB Display" p.41
Connecting Equipment
28
Connecting Image Sources
To project images from DVD players or VHS video and so on, connect to the projector using one of the following methods.
A
When using a commercially available video cable
B
Connect the video output port on the image source to the projector's Video port using a commercially available video cable.
You can output audio from the projector's speaker by connecting the audio output port on the image source to the projector's Audio-L/R port using a commercially available
audio cable.
When using a commercially available S-video cable
Connect the video output port on the image source to the projector's S-Video port using a commercially available video cable.
You can output audio from the projector's speaker by connecting the audio output port on the image source to the projector's Audio-L/R port using a commercially available
audio cable.
C D When using the optional component video cable
s "Optional Accessories and Consumables" p.146
Connect the component output port on the image source to the projector's Computer1 or Computer2 port.
You can output audio from the projector's speaker by connecting the image source's audio output port to the projector's Audio1 or Audio2 port using a commercially available
audio cable.
When using a commercially available HDMI cable
E
Connect the HDMI port on the image source to the projector's HDMI port using a commercially available HDMI cable.
You can send the audio with the projected image.
Connecting Equipment
Attention
• If the input source is on when you connect it to the projector, it could cause a malfunction.
• If the orientation or shape of the plug differs, do not try to force it in. The device could be damaged or could malfunction.
29
Connecting Equipment
a
30
• You can switch the audio input by using Audio Input.
s Extended - Operation - Audio Input p.103
• If the source you want to connect to has an unusually shaped port, use the cable supplied with the device or an optional cable to connect to the projector.
• When using a commercially available 2RCA(L/R)/stereo mini-pin audio cable, make sure it is labeled "No resistance".
Connecting Equipment
31
Connecting USB Devices
You can connect devices such as USB memory, the optional Document Camera, and USB compatible hard disks and digital cameras.
Using the USB cable supplied with the USB device, connect the USB device to the USB-A port on the projector.
When the USB device is connected, you can project image files on the USB memory or digital camera using Slideshow.
s "Projecting Without a Computer (Slideshow)" p.74
If the Document Camera is connected while projecting images from another input port, press the [USB] button on the remote control, or the [Source Search]
button on the control panel, to switch to images from the Document Camera.
s "Automatically Detect Input Signals and Change the Projected Image (Source Search)" p.40
a
While projecting images from a USB device, if you want to connect an audio output device, connect it to the Audio2 port.
Connecting Equipment
32
Attention
•
•
•
•
If you use a USB hub, operation may not be performed correctly. Devices such as digital cameras and USB devices should be connected to the projector directly.
When connecting and using a USB-compatible hard disk, make sure you connect the AC adaptor supplied with the hard disk.
Connect a digital camera or hard disk to the projector using a USB cable supplied with or specified for use with the device.
Use a USB cable less than 3 m in length. If the cable exceeds 3 m, Slideshow may not function correctly.
Removing USB devices
After finishing projecting, remove USB devices from the projector. For devices such as digital cameras or hard disks, turn off the device and then remove it from
the projector.
Connecting Equipment
Connecting a microphone
You can output microphone audio from the projector's speaker by connecting a commercially available dynamic microphone.
a
• Plug-in-power is not supported.
• Adjust Mic Input Level if the microphone audio is difficult to hear, or if it is too loud resulting in a crackling sound.
s Settings - Mic Input Level p.101
• Make the following settings to output audio from a microphone when the projector is in standby mode.
Set Standby Mode to Communication On. s Extended - Standby Setup - Standby Mode p.103
Set Standby Microphone to On. s Extended - Standby Setup - Standby Microphone p.103
33
Connecting Equipment
Connecting External Equipment
You can output images and audio by connecting an external monitor or speaker.
A When outputting images to an external monitor
Connect the external monitor to the projector's Monitor Out port using the cable supplied with the external monitor.
B When outputting audio to an external speaker
Connect the external speaker to the projector's Audio Out port using a commercially available audio cable.
34
Connecting Equipment
a
35
• If you set Standby Mode to Communication On, you can output images to an external monitor even if the projector is in standby mode. You can also output
audio to an external speaker. Audio input from the HDMI port, USB-A port, USB-B port, or the LAN port cannot be output.
s Extended - Standby Setup - Standby Mode p.103
• Only analog RGB signals from the Computer1 port can be output to an external monitor. You cannot output signals input from other ports or component video
signals.
• Setting gauges for functions such as Keystone, Configuration menu, or Help screens are not output to the external monitor.
• When the audio cable jack is inserted into the Audio Out port, audio stops being output from the projector's built-in speakers and switches to external
output.
Connecting Equipment
Connecting a LAN Cable
Connect a LAN port on network hubs or other equipment to the projector's LAN port with a commercially available 100BASE-TX or 10BASE-T LAN
cable.
a
To prevent malfunctions, use a category 5 shielded LAN cable.
36
Connecting Equipment
Installing the Optional Wireless LAN Unit
a
Remove both of the cable cover fixing screws to open the cable
cover.
37
b
Install the Wireless LAN unit.
Basic Usage
This chapter explains how to project and adjust images.
Projecting images
From Installation to Projection
This section explains the procedure for connecting the projector to a
computer with the computer cable and projecting images.
39
d
e
Turn on the computer.
Change the computer's screen output.
When using a laptop computer, you need to change the screen
output from the computer.
Hold down the Fn key (function key), and press the b key.
a
• The method for changing differs depending on the computer
being used. See the documentation supplied with the
computer.
• Press the [t] button twice to turn the projector off.
If the image is not projected, you can change the projected image using one
of the following methods.
• Press the [Source Search] button on the control panel or the remote
control.
s "Automatically Detect Input Signals and Change the Projected Image
(Source Search)" p.40
• Press the button for the target port on the remote control.
s "Switching to the Target Image Using the Remote Control" p.41
ON
a
After projecting the image, adjust the image if necessary.
s "Correcting Keystone Distortion" p.45
s "Correcting the Focus" p.50
a
b
c
Connect the projector to an electrical outlet with the power cord.
Connect the projector to the computer with the computer cable.
Turn on the projector.
Projecting images
40
Automatically Detect Input Signals and Change
the Projected Image (Source Search)
Press the [Source Search] button to project images from the port currently
receiving an image.
Using Remote Control
Computer1
LAN
Computer2
USB
Using the Control Panel
S-Video
Video
USB Display
HDMI
When two or more image sources are connected, press the [Source Search]
button until the target image is projected.
When your video equipment is connected, start playback before beginning
this operation.
a
The following screen is displayed while no image signals are input.
Projecting images
41
Switching to the Target Image Using the Remote
Control
You can change directly to the target image by pressing the following
buttons on the remote control.
Remote control
Projecting with USB Display
You can use the supplied or a commercially available USB cable to connect
the projector to a computer to project images from the computer.
You can send the computer's audio with the projected image.
Set USB Type B to USB Display/Easy Interactive Function or Wireless
Mouse/USB Display to use USB Display on EB-485Wi/EB-480i/EB-475Wi.
s Extended - USB Type B p.103
System requirements
For Windows
OS
A Each time the button is pressed, it cycles through the images being input
from the following sources.
• Computer1 port
• Computer2 port
B Each time the button is pressed, it cycles through the images being input
from the following sources.
• S-Video port
• Video port
• HDMI port
C Each time the button is pressed, it cycles through the images being input
from the following sources.
• USB Display
• Images from the device connected to the USB-A port
D Changes to the images projected with EasyMP Network Projection. When
projecting using the optional Quick Wireless Connection USB Key, this
button switches to that image.
CPU
Windows 2000*1
Windows XP
Professional 32 bit
Home Edition 32 bit
Tablet PC Edition 32 bit
Windows Vista
Ultimate 32 bit
Enterprise 32 bit
Business 32 bit
Home Premium 32 bit
Home Basic 32 bit
Windows 7
Ultimate 32/64 bit
Enterprise 32/64 bit
Professional 32/64 bit
Home Premium 32/64 bit
Home Basic 32 bit
Starter 32 bit
Mobile Pentium III 1.2 GHz or faster
Recommended: Pentium M 1.6 GHz or faster
Projecting images
42
Amount of Mem‐
ory
256 MB or more
Recommended: 512 MB or more
Hard Disk Space
20 MB or more
Display
Resolution of no less than 640x480 and no higher than
1600x1200.
Display color of 16-bit color or greater
*1 Service Pack 4 only
Connecting for the first time
The first time you connect the projector and the computer using the USB
cable, the driver needs to be installed. The procedure is different for
Windows and Mac OS X.
a
For Mac OS X
OS
Mac OS X 10.5.x 32 bit
Mac OS X 10.6.x 32/64 bit
Mac OS X 10.7.x 32/64 bit
CPU
Power PC G4 1GHz or faster
Recommended: Core Duo 1.83GHz or faster
Amount of Memo‐
ry
512 MB or more
Hard Disk Space
20 MB or more
Display
Resolution of no less than 640x480 and no higher than
1680x1200.
Display color of 16-bit color or greater
• You do not need to install the driver the next time you connect.
• When inputting images from multiple sources, change the input
source to USB Display.
• If you are using a USB hub, operations may not be performed
correctly. Connect the USB cable directly to the projector.
• You cannot change option settings while using USB Display.
For Windows
a
Connect the computer's USB port to the projector's USB-B port
using the supplied or a commercially available USB cable.
a
For Windows 2000 or Windows XP, a message asking you if
you want to restart your computer may be displayed. Select
No.
For Windows 2000
Double-click Computer, EPSON PJ_UD, and then
EMP_UDSE.EXE.
For Windows XP
Driver installation starts automatically.
For Windows Vista/Windows 7
When the dialog box is displayed, click Run EMP_UDSE.exe.
b
When the License Agreement screen is displayed, click Agree.
Projecting images
c
d
Computer images are projected.
It may take a while for computer images to be projected. Until the
computer images are projected, leave the equipment as is and do not
disconnect the USB cable or turn off the power of the projector.
Disconnect the USB cable when you are finished.
When disconnecting the USB cable, there is no need to use Safely
Remove Hardware.
a
• If it is not installed automatically, double-click My Computer
- EPSON_PJ_UD - EMP_UDSE.EXE on your computer.
43
d
When the License Agreement screen is displayed, click Agree.
Enter the administrator authority password and start the installation.
When the installation is complete, the USB Display icon is displayed
in the Dock and menu bar.
e
Computer images are projected.
f
When you have finished, select Disconnect from the menu bar or
from the USB Display icon on the Dock. You can then disconnect
the USB cable.
• If nothing is projected for some reason, click All Programs EPSON Projector - Epson USB Display - Epson USB
Display Vx.xx on your computer.
It may take a while for computer images to be projected. Until the
computer images are projected, leave the equipment as is and do not
disconnect the USB cable or turn off the power of the projector.
a
• When using a computer running Windows 2000 under user
authority, a Windows error message is displayed and you may
not be able to use the software. In this case, try updating
Windows to the latest version, restart, and then try to connect
again.
For more details, contact your local dealer or the nearest
address provided in the following document.
s Epson Projector Contact List
• If the USB Display setup folder is not displayed automatically
in the Finder, double-click EPSON PJ_UD - USB Display
Installer on your computer.
• If nothing is projected for some reason, click the USB
Display icon in the Dock.
• If there is no USB Display icon in the Dock, double-click
USB Display from the Applications folder.
• If you select Exit from the USB Display icon menu on the
Dock, USB Display does not start automatically when you
connect the USB cable.
For Mac OS X
a
b
c
Connect the computer's USB port to the projector's USB-B port
using the supplied or a commercially available USB cable.
Uninstalling
The Setup folder of USB Display is displayed in the Finder.
For Windows 2000
Double-click the USB Display Installer icon.
a
b
c
d
Follow the on-screen instructions to install.
Click Start, select Settings, and then click Control Panel.
Double-click Add/Remove Programs.
Click Change or Remove Programs.
Select Epson USB Display and click Change/Remove.
Projecting images
For Windows XP
a
b
c
Click Start, and then click Control Panel.
Double-click Add or Remove Programs.
Select Epson USB Display and click Remove.
For Windows Vista/Windows 7
a
b
c
Click Start, and then click Control Panel.
Click Uninstall a program under Programs.
Select Epson USB Display and click Uninstall.
For Mac OS X
a
b
Open the Applications folder, double-click USB Display, and then
double-click Tool.
Run USB Display Uninstaller.
44
Adjusting Projected Images
Correcting Keystone Distortion
You can correct keystone distortion using one of the following methods.
• H/V-Keystone
Manually correct distortion in the horizontal and vertical directions
independently.
45
H/V-Keystone
Manually correct distortion in the horizontal and vertical directions
independently. H/V-Keystone correction is ideal for fine-tuning keystone
distortion.
You can use H/V-Keystone to correct the projected image under the
following conditions.
Correction angle: Approx. 5˚ right and left/Approx. 5˚ up and down
a
Press the [w] or [v] buttons on the control panel during
projection to display the Keystone screen.
b
Press the following buttons to correct keystone distortion.
• Quick Corner
Manually correct the four corners independently.
a
When you correct keystone distortion, the projected image may be
reduced.
Press the [w] or [v] buttons to correct vertical distortion.
Adjusting Projected Images
46
Press the [Tele] or [Wide] buttons to correct horizontal distortion.
a
You can set H/V-Keystone from the Configuration menu.
s Settings - Keystone - H/V-Keystone p.101
c
Select Quick Corner, and then press the [
d
Select the corner to correct using the [
] button.
Quick Corner
This allows you to manually correct each of the four corners of the
projected image separately.
a
Press the [Menu] button while projecting.
s "Using the Configuration Menu" p.95
Using Remote Control
b
Select Keystone from Settings.
Using the Control Panel
], [
], [ ], and[ ]
buttons on the remote control, or the [w], [v], [Wide], and [Tele]
buttons on the control panel, and then press the [ ] button.
Adjusting Projected Images
e
Correct the position of the corner using the [
47
], [
], [ ], and
[ ] buttons on the remote control, or the [w], [v], [Wide],
and [Tele] buttons on the control panel.
When you press the [
displayed.
] button, the screen shown in step 4 is
If the message "Cannot adjust any further." is displayed while
adjusting, you cannot adjust the shape any further in the direction
indicated by the gray triangle.
f
Repeat procedures 4 and 5 as needed to adjust any remaining
corners.
g
When you are done, press the [Esc] button to exit the correction
menu.
Because Keystone was changed to Quick Corner, the corner
selection screen shown in step 4 is displayed the next time you press
the [w] or [v] buttons on the control panel. Change Keystone to
H/V-Keystone if you want to perform horizontal and vertical
correction using the [w] and [v] buttons on the control panel.
s Settings - Keystone - H/V-Keystone p.101
Adjusting Projected Images
a
If the [Esc] button is held down for about two seconds while
the corner selection screen from step 4 is displayed, the
following screen is displayed.
Reset Quick Corner: Resets the result of Quick Corner
corrections.
Switch to H/V-Keystone: Switches the correction method to
H/V-Keystone.
s "Settings Menu" p.101
48
Adjusting the Position of the Image (Image Shift)
You can fine tune the position of the image without moving the projector.
a
Perform Adjust Zoom or Keystone.
s "Adjusting the Image Size" p.48
s "Correcting Keystone Distortion" p.45
The Image Shift screen is displayed after you have made adjustments.
Adjusting the Image Size
Press the [Wide] and [Tele] buttons on the control panel to adjust the size
of the projected image.
a
You can also make adjustments from the configuration menu.
s Settings - Zoom p.101
b
Adjust the position of the projected image.
Adjusting Projected Images
49
a
• You cannot adjust the image position when Zoom is set to the
maximum Wide position.
• The Image Shift setting is retained even if the projector is turned off.
You need to re-adjust the position if you change the installation
location or angle of the projector.
• You can also use the Configuration menu to adjust the position of
the image.
s Settings - Image Shift p.101
Using Remote Control
Using the Control Panel
Adjusting the Vertical Position of the Image
(Models Supplied with the Feet Only)
Extend the feet. You can adjust the vertical position of the image by tilting
the projector up to 1.5˚.
a
You can shift the image diagonally by pressing any pair of adjacent
[
], [
The larger the angle of tilt, the harder it becomes to focus. Install the
projector so that it only needs to be tilted at a small angle.
Raising the height of the image
], [ ], and [ ] buttons, or a combination
of [w], [v], [Wide], and [Tele] buttons.
c
Press the [Esc] button to close the adjustment screen.
The adjustment screen disappears if no operation is performed after
approximately 10 seconds.
A You can raise the height of the image by extending the rear feet.
B Retract the rear feet to return the image to its original height.
Adjusting Projected Images
Lowering the height of the image
50
B Retract the rear foot.
Correcting the Focus
You can correct the focus using the focus lever.
A You can lower the height of the image by extending the front foot.
B Retract the front foot to return the image to its original height.
Adjusting the Horizontal Position of the Image
(Models Supplied with the Feet Only)
Extend and retract the rear feet to adjust the projector's horizontal tilt.
Adjusting the Volume
You can adjust the volume using one of the following methods.
A Extend the rear foot.
Adjusting Projected Images
51
• Press the [Volume] buttons on the remote control to adjust the volume.
[a] Decreases the volume.
[b] Increases the volume.
Remote control
• Adjust the volume from the Configuration menu.
s Settings - Volume p.101
Caution
Do not start when the volume is set too high.
A sudden increase in volume may cause loss of hearing. Always lower the
volume before powering off, so that you can power on and then gradually
increase the volume.
Selecting the Projection Quality (Selecting Color
Mode)
You can easily obtain the optimum image quality simply by selecting the
setting that best corresponds to your surroundings when projecting. The
brightness of the image varies depending on the mode selected.
Mode
Dynamic
Application
Ideal for use in a bright room. This is the brightest
mode, and reproduces shadow tones well.
Mode
Application
Presentation
Ideal for making presentations using color materials
in a bright room.
Theatre
Ideal for watching films in a dark room. Gives
images a natural tone.
Photo*1
Ideal for projecting still pictures, such as photos, in
a bright room. The images are vivid and brought
into contrast.
Sports *2
Ideal for watching TV programmes in a bright
room. The images are vivid and brought to life.
sRGB
Ideal for images that conform to the sRGBg color
standard.
Blackboard
Even if you are projecting onto a blackboard
(greenboard), this setting gives your images a
natural tint, just like when projecting onto a screen.
Whiteboard
Ideal for making presentations using a whiteboard.
*1 This selection is only available when the input signal is RGB or when the
source is USB Display, USB, or LAN.
*2 This selection is only available when the input signal is component video, or
when the input source is Video or S-Video.
Each time you press the [Color Mode] button, the Color Mode name is
displayed on the screen and the Color Mode changes.
Remote control
Adjusting Projected Images
a
52
You can set Color Mode from the Configuration menu.
s Image - Color Mode p.98
Setting Auto Iris
By automatically setting the luminance according to the brightness of the
displayed image, it lets you enjoy deep and rich images.
a
Press the [Menu] button.
s "Using the Configuration Menu" p.95
Using Remote Control
Using the Control Panel
c
d
Select On.
The setting is stored for each Color Mode.
Press the [Menu] button to finish making settings.
a
b
Auto Iris can only be set when the Color Mode is set to
Dynamic or Theatre.
Select Auto Iris from Image.
Changing the Aspect Ratio of the Projected Image
You can change the Aspect Ratiog of the projected image to suit the type,
the ratio of height and width, and the resolution of the input signals.
Available Aspect Modes vary depending on the image signal currently being
projected.
Adjusting Projected Images
53
Changing methods
Each time you press the [Aspect] button on the remote control, the aspect
mode name is displayed on the screen and the aspect ratio changes.
Remote control
a
You can set the aspect ratio from the Configuration menu.
s Signal - Aspect p.99
Changing the aspect mode (EB-485Wi/EB-485W/EB-475Wi/EB-475W
only)
A
B
C
D
E
Normal or Auto
16:9
Full
Zoom
Native
Projecting images from a computer
Projecting images from video equipment or from the HDMI port
The following shows projection examples for each aspect mode.
Each time the [Aspect] button on the remote control is pressed, the aspect
mode changes in the order Normal or Auto, 16:9, Full, Zoom, and
Native.
Aspect mode
Example: 1080p signal input (resolution: 1920x1080, aspect ratio: 16:9)
Normal
Input Signal
XGA 1024X768(4:3)
WXGA 1280X800(16:10)
Adjusting Projected Images
Aspect mode
54
Input Signal
XGA 1024X768(4:3)
Changing the aspect mode (EB-480i/EB-480/EB-470 only)
WXGA 1280X800(16:10)
Projecting images from video equipment
16:9
Each time the [Aspect] button is pressed, the aspect mode changes in the
order 4:3 and 16:9.
When inputting a 720p/1080i signal and the aspect mode is set to 4:3, a 4:3
zoom is applied (the right and left sides of the image are cut off).
Full
Example: 720p signal input (resolution: 1280x720, aspect ratio: 16:9)
Zoom
A 4:3
B 16:9
Native
Projecting images from the HDMI port
Each time the [Aspect] button is pressed, the aspect mode changes in the
order Auto, 4:3, and 16:9.
a
Example: 1080p signal input (resolution: 1920x1080, aspect ratio: 16:9)
If parts of the image are missing, set the Resolution setting to Wide
or Normal from the Configuration menu, according to the size of the
computer panel.
s Signal - Resolution p.99
A Auto
Adjusting Projected Images
55
B 4:3
C 16:9
Projecting images from a computer
Each time the [Aspect] button is pressed, the aspect mode changes in the
order Normal, 4:3, and 16:9.
The following shows projection examples for each aspect mode.
Aspect mode
Input Signal
XGA 1024X768(4:3)
WXGA 1280X800(16:10)
Normal
4:3
16:9
a
If parts of the image are missing, set the Resolution setting to Wide
or Normal from the Configuration menu, according to the size of the
computer panel.
s Signal - Resolution p.99
Useful Functions
This chapter explains useful functions for giving presentations and so on, and the security functions.
Easy Interactive Function (EB-485Wi/EB-480i/EB-475Wi only)
57
Introducing the Easy Interactive Function
The Easy Interactive Function allows you to perform the following
operations using the Easy Interactive Pen.
Drawing with the projector's built-in function
You can write and draw on the projected screen using the projector's
built-in drawing function without having to use any additional software.
You can draw on any image source.
s "Drawing with the Projector's Built-in Function" p.58
Operating as a mouse and drawing by connecting to a computer
(Computer Interactive)
You can connect the projector to a computer to operate the computer from
the projected screen. This makes presentations and lessons effective and
easy to understand.
Two people can use Easy Interactive Pens simultaneously by using the
supplied drawing software Easy Interactive Tools.
s "Operating as a mouse and drawing by connecting to a computer
(Computer Interactive)" p.64
Easy Interactive Function (EB-485Wi/EB-480i/EB-475Wi only)
Attention
The Easy Interactive Function operates by infrared communication. Note the
following important points when using this function.
• Make sure there is no strong light or sunlight shining on the Easy Interactive
Function receiver or the projection screen.
• If there is any dust stuck to the Easy Interactive Function receiver, it could
interfere with infrared communication and you may not be able to use the
function normally.
• Do not put paint or any stickers on the cover of the Easy Interactive
Function receiver.
• Install the projector so that the Easy Interactive Function receiver is not too
close to fluorescent lights.
• Do not use an infrared remote control or infrared microphone in the same
room because the Easy Interactive Pen may malfunction.
• The Easy Interactive Function may be interrupted by electromagnetic
interference from nearby equipment (such as electric motors or transformers).
• The Easy Interactive Pen is not waterproof. Do not use it with wet hands, or
in locations where it may get wet.
• Do not hold the black section of the pen tip of the Easy Interactive Pen, and
make sure this section does not get damaged or soiled. Otherwise, the Easy
Interactive Pen may not work.
• When operating Keystone, performance for the Easy Interactive Function may
decline.
58
Drawing with the Projector's Built-in Function
Procedure
a
b
Turn on the projector.
Perform the pen calibration.
You can skip this step if pen calibration is already complete.
s "Calibrating the pen" p.59
c
Put the Easy Interactive Pen close to the projected screen near the
d
Click one of the toolbar tabs [
toolbar tabs [
] on the left and right of the screen.
].
The toolbar is displayed.
When the toolbar is displayed, you can write on the projected screen using
the Easy Interactive Pen.
Easy Interactive Function (EB-485Wi/EB-480i/EB-475Wi only)
s "Easy Interactive Pen (EB-485Wi/EB-480i/EB-475Wi Only)" p.20
s "Toolbar functions" p.62
a
The projector's built-in drawing function is not available if both of the
following conditions are met.
• Extended - USB Type B is set to Easy Interactive Function or USB
Display/Easy Interactive Function from the configuration menu.
• Images are projected from the source specified in Extended - Easy
Interactive Function - Use Source from the configuration menu.
59
Calibrating the pen
You need the Easy Interactive Pen to use the Easy Interactive Function.
Make sure you perform pen calibration when using the Easy Interactive Pen
for the first time so that the projector recognizes the position of the pen
correctly.
Auto Calibration
This function automatically calibrates the pen.
a
Set Extended - Easy Interactive Function to Auto Calibration
from the configuration menu.
b
Adjust the focus by following the on-screen instructions.
Easy Interactive Function (EB-485Wi/EB-480i/EB-475Wi only)
60
If Auto Calibration is unsuccessful, try Manual Calibration.
s "Manual Calibration" p.60
Manual Calibration
This function allows you to manually calibrate the pen.
a
Set Extended - Easy Interactive Function to Manual Calibration
from the configuration menu.
b
Adjust the focus by following the on-screen instructions.
s "Correcting the Focus" p.50
c
Select "Yes".
d
The pattern image is projected and calibration starts.
Use the [ ] button on the remote control or control panel to select
"Yes". You cannot select Easy Interactive Pen when performing
operations from the configuration menu.
Wait until calibration is complete.
Do not obstruct the projected light while the pattern image is being
projected.
a
• Select [
] using Easy Interactive Pen on the toolbar and execute
Auto Calibration if the discrepancy is small.
• However, execute Auto Calibration from the remote control or
control panel when you are calibrating the pen for the first time.
• For pen positioning, do not switch between making operations using
the remote control and making operations using the Easy Interactive
Pen.
Easy Interactive Function (EB-485Wi/EB-480i/EB-475Wi only)
61
a
e
Make sure you touch the center of the dot. Otherwise, it may
not be positioned correctly.
The dot appears at the top left first and then moves towards the
bottom right.
Repeat step 4 until all of the dots disappear.
c
Use the [ ] button on the remote control or control panel to
select "Yes".
d
A dot is displayed on the projected screen.
Touch the center of the dot with the tip of the Easy Interactive Pen.
The dot disappears and then appears at the next position.
Easy Interactive Function (EB-485Wi/EB-480i/EB-475Wi only)
a
• If you touch the wrong position, press the [Esc] button on the
remote control or control panel to return to the previous dot.
You cannot go back further than the previous dot.
• Press and hold the [Esc] button to cancel the calibration.
• It may take several seconds after all of the dots have
disappeared until calibration is complete.
62
Whiteboard mode
You can project solid color backgrounds such as a
whiteboard and write or draw text and pictures. In
addition to the plain background, you can also choose
other background patterns such as lines and grid lines.
Annotation mode
When you need to calibrate the pen
The position where you are drawing with the Easy Interactive Pen and
where the drawing is displayed may not match in the following situations.
• After performing Keystone correction.
• After adjusting the image size.
• After performing Image Shift.
• After changing the projector's position.
Calibrate the pen again if you notice any discrepancy in positioning.
Toolbar functions
The following toolbar modes are available.
Annotation mode
You can draw lines and shapes on the projected image.
A
Annotation mode tab
Switches to Annotation mode.
Whiteboard mode
Easy Interactive Function (EB-485Wi/EB-480i/EB-475Wi only)
B
Whiteboard mode tab
Switches to Whiteboard mode.
C
Undo
Undoes the previous operation.
D
Redo
Cancels an undo operation and restores the previous status.
E
Freeze (Annotation mode only)
Pauses the projected image. Each time you touch the icon, Freeze turns
on or off.
a
F
63
G
E-Zoom
Displays a target allowing you to enlarge the image at the center of the
target. You can move the target with the Easy Interactive Pen.
[
]: Enlarges the image.
[
]: Reduces the image.
[
]: Increases the magnification by one.
[
]: Quits E-Zoom.
a
You can also use the [Freeze] button on the remote
control.
• You cannot use E-Zoom from the remote control,
document camera, or Crestron RoomView while
operating the Easy Interactive Pen in E-Zoom.
s "Enlarging Part of the Image (E-Zoom)" p.69
s "About Crestron RoomView " p.90
®
s "Freezing the Image (Freeze)" p.67
Select background (Whiteboard mode only)
Allows you to select a pattern from the six background patterns
provided for Whiteboard mode.
• You can scroll the enlarged image by dragging it
with the Easy Interactive Pen.
®
H
Calibrating the pen
Carries out Auto Calibration.
s "Auto Calibration" p.59
I
Pen
Switches to a pen to draw freely. Click [
] on the left of the icon to
change the color and width of the pen line.
J
Highlighter pen
Switches to a highlighter pen that can draw translucent lines. Click
[
] on the left of the icon to change the color and width of the
highlighter pen.
K
Black pen
Switches to a black pen to draw freely. Click on the right of the icon to
draw thick lines, and click on the left of the icon to draw fine lines.
L
Red pen
Switches to a red pen to draw freely. Click on the right of the icon to draw
thick lines, and click on the left of the icon to draw fine lines.
Easy Interactive Function (EB-485Wi/EB-480i/EB-475Wi only)
M
Blue pen
Switches to a blue pen to draw freely. Click on the right of the icon to
draw thick lines, and click on the left of the icon to draw fine lines.
N
Eraser
Switches to an eraser. Click on the right of the icon to erase wider areas,
and click on the left of the icon to erase narrower areas.
O
a
Clear screen
Clears everything drawn on the displayed page.
• Click [
64
You need a drawing function already available on your computer.
The Easy Interactive Tools software is supplied with this projector. See the
following manual for more information on the Easy Interactive Tools
functions.
s Easy Interactive Tools Ver.2 Operation Guide
a
• Make the following settings to link with the computer's functions.
• Set Extended - USB Type B to Easy Interactive Function or USB
Display/Easy Interactive Function from the configuration menu.
• Set the source where the computer is connected in Extended Easy Interactive Function - Use Source from the configuration
menu.
s Extended - Easy Interactive Function p.103
] to hide the toolbar.
• You can display the toolbar again by clicking one of the toolbar tabs
[
] displayed on the left and right of the screen.
• If you click [
], the toolbar is hidden each time you draw
something. By default, the toolbar is always displayed.
• The toolbar tabs [
] can be moved up and down.
• The toolbar tabs [
] disappear after a set length of time if they
• Connect the projector to the computer using a USB cable to link
with the computer's functions.
s "Connecting USB Devices" p.31
• You cannot use the projector's built-in drawing function if you
switch to the image source set in Use Source.
are not used. Put the Easy Interactive Pen close to the projected
screen to display the toolbar tabs [
].
Install Easy Interactive Driver (Mac OS X only)
Easy Interactive Driver is required to use the Easy Interactive Pen with Mac
OS X.
Operating as a mouse and drawing by connecting
to a computer (Computer Interactive)
You can connect the projector to a computer to operate the computer from
the projected screen and allow two people to draw simultaneously.
You need to install Easy Interactive Driver for Mac OS X.
s "Install Easy Interactive Driver (Mac OS X only)" p.64
System Requirements
OS
Mac OS X 10.3.9 or later
Mac OS X 10.4.x
Mac OS X 10.5.x
Mac OS X 10.6.x
Mac OS X 10.7.x
Easy Interactive Function (EB-485Wi/EB-480i/EB-475Wi only)
CPU
Power PC G3 900 MHz or faster
Recommended: Intel Core Duo 1.5 GHz or faster
Amount of Memo‐
ry
256 MB or more
Recommended: 512 MB or more
Hard Disk Space
100 MB or more
Display
Resolutions no lower than XGA (1024 x 768) and no higher
than WUXGA (1920 x 1200)
Display color in 16-bit color or greater
Installing
a
You can skip the following procedure if you installed Easy Interactive
Tools using the Easy Install option as this already installs the Easy
Interactive Driver.
s Easy Interactive Tools Ver.2 Operation Guide
a
b
Turn on your computer.
c
d
Double-click the Install Navi icon in the EPSON window.
e
Restart the computer.
b
c
Run Easy Interactive Driver Uninstaller in the Tools folder.
Follow the on-screen instructions to uninstall.
Operating the computer with a pen instead of a mouse
You can operate a computer using the Easy Interactive Pen instead of a
mouse.
If you set Enable Right Click to On in Extended - Easy Interactive
Function from the configuration menu, a long press of the Easy Interactive
Pen functions as a right click.
Allowing two people to use pens at the same time
Easy Interactive Tools allows two people to use Easy Interactive Pens at the
same time.
s Easy Interactive Tools Ver.2 Operation Guide
Insert the "EPSON Projector Software for Easy Interactive Function"
CD-ROM into your computer.
Select Custom Install, and then follow the on-screen instructions
to install.
Uninstalling
a
65
Open the Applications folder and double-click Easy Interactive
Driver.
Set Number of Pen Users to Two Users in Extended - Easy Interactive
Function from the configuration menu.
a
• When Number of Pen Users is set to One User, you can use the
Easy Interactive Pen with tablet PCs in Windows Vista/7. You can
also use ink features for Office in Windows Vista/7.
• You can set Easy Interactive Pen operations from the configuration
menu.
• Set Pen Operation Mode to Pen to enable the pen function in
Windows Vista/7.
• You can swap Right Click and Left Click in Advanced - Pen Tip
Button.
s Extended - Easy Interactive Function p.103
Easy Interactive Function (EB-485Wi/EB-480i/EB-475Wi only)
66
Adjusting the pen operation area
a
When using the Easy Interactive Function by connecting to a computer, the
pen operation area is automatically adjusted if the resolution of the
computer changes. You do not need to perform pen alignment again.
a
You can turn this function On or Off in Auto Adjust Pen Area from
the configuration menu. The default setting is On.
b
• Adjust to fit the projected image within the screen.
• Display the computer's desktop screen so that you can check
the position of the mouse pointer easily.
Use the [
] button on the remote control to select "Yes".
s Extended - Easy Interactive Function - Advanced p.103
If you notice the Easy Interactive Pen is out of position even when Auto
Adjust Pen Area is set to On, you can try Manual Adj. Pen Area.
s "Manual Adj. Pen Area" p.66
Manual Adj. Pen Area
a
Select Manual Adj. Pen Area for Easy Interactive Function from
the configuration menu.
The mouse pointer moves towards the top left.
c
When the mouse pointer stops at the top left, touch the tip of the
mouse pointer with the Easy Interactive Pen.
The mouse pointer moves towards the bottom right.
d
When the mouse pointer stops at the bottom right, touch the tip
of the mouse pointer with the Easy Interactive Pen.
Projection Functions
Hiding the Image and Sound Temporarily (A/V
Mute)
You can switch off the image on the screen when you want to focus the
audience's attention on what you are saying, or when you do not want to
display operations such as changing files.
67
a
• If you use this function when projecting moving images, the images
and sound continue to be played back by the source, and you cannot
return to the point where A/V Mute was activated.
• Microphone audio is still output even when A/V Mute is turned
on.
• You can select the screen displayed when the [A/V Mute] button is
pressed from the Configuration menu.
s Extended - Display - A/V Mute p.103
• The lamp is still lit during A/V Mute, so the lamp hours continue to
accumulate.
Freezing the Image (Freeze)
Each time you press the [A/V Mute] button, A/V Mute turns on or off.
Remote control
When Freeze is activated on moving images, the frozen image continues to
project on the screen, so you can project a moving image one frame at a
time like a still photo. Also, you can perform operations such as changing
between files during presentations from a computer without projecting any
images if the Freeze function is activated beforehand.
Each time you press the [Freeze] button, Freeze turns on or off.
Remote control
Projection Functions
a
• Audio does not stop.
• For moving images, the images continue to play back while the
screen is frozen, so it is not possible to resume projection from the
point where the screen was frozen.
• If the [Freeze] button is pressed while the Configuration menu or
the Help screen is displayed, the menu or the Help screen that is
displayed is closed.
• Freeze still works while E-Zoom is being used.
Pointer Function (Pointer)
This allows you to move a pointer icon on the projected image, and helps
you draw attention to the area you are talking about.
68
b
Move the Pointer icon (
Remote control
When any pair of adjacent [
Display the Pointer.
Each time you press the [Pointer] button, the pointer appears or
disappears.
Remote control
], [
], [ ], or [ ] buttons are
pressed at the same time, the pointer can be moved diagonally.
a
a
).
You can select the shape of the pointer icon from the
Configuration menu.
s Settings - Pointer Shape p.101
Projection Functions
69
Enlarging Part of the Image (E-Zoom)
b
This is useful when you want to expand images to see them in greater
detail, such as graphs and tables.
a
Remote control
) to the area of the image that you want to
enlarge.
Remote control
When any pair of adjacent [
Start E-Zoom.
Press the [z] button to display the Cross (
Move the Cross (
], [
], [ ], or [ ] buttons are
pressed at the same time, the pointer can be moved diagonally.
).
c
Enlarge.
Remote control
[z] button: Expands the area each time
it is pressed. You can expand quickly by
holding the button down.
[x] button: Reduces images that have
been enlarged.
[Esc] button: Cancels E-Zoom.
a
• The enlargement ratio appears on the screen. The selected
area can be enlarged to between 1 to 4 times in 25
incremental steps.
• During enlarged projection, press the [
[ ] buttons to scroll the image.
], [
], [ ], and
Projection Functions
70
Using the Remote Control to Operate the Mouse
Pointer (Wireless Mouse)
You can control the computer's mouse pointer from the projector's remote
control. This function is called Wireless Mouse.
• HDMI
s "Switching to the Target Image Using the Remote Control"
p.41
Once set, the mouse pointer can be controlled as follows.
Moving the mouse pointer
The following operating systems are compatible with Wireless Mouse.
Windows
Windows
Windows
Windows
Windows
Windows
Windows
Windows
OS
*
[
Mac OS X
98
98SE
Me
2000
XP
Vista
7
Mac
Mac
Mac
Mac
Mac
OS
OS
OS
OS
OS
X
X
X
X
X
][
][ ][ ] buttons:
Moves the mouse pointer.
10.3.x
10.4.x
10.5.x
10.6.x
10.7.x
Mouse clicks
[Esc] button: Right click.
[ ] button: Left click. Press quickly
twice to double-click.
It may not be possible to use the Wireless Mouse function under some
versions of the operating systems.
Use the following procedure to enable the Wireless Mouse function.
a
Set USB Type B to Wireless Mouse/USB Display from the
configuration menu. (EB-485Wi/EB-480i/EB-475Wi only)
Drag and drop
While holding down the [
s Extended - USB Type B p.103
b
press the [
], [
] button,
], [ ], or [ ]
button to drag.
Connect the projector to the computer with the supplied or a
commercially available USB cable.
Release the [ ] button to drop at the
desired location.
s "Connecting a Computer" p.26
c • USB Display
Change the source to one of the following.
• Computer1
• Computer2
Page Up/Down
[[] button: Moves to the previous page.
[]] button: Moves to the next page.
Projection Functions
a
• When any pair of adjacent [
71
], [
], [ ], or [ ] buttons are
pressed at the same time, the pointer can be moved diagonally.
• If the mouse button settings are set to reverse on the computer, the
operation of the remote control buttons will also be reversed.
• The Wireless Mouse function does not work under the following
conditions.
• When Extended - USB Type B is set to anything other than
Wireless Mouse/USB Display (EB-485Wi/EB-480i/EB-475Wi only).
• When displaying the configuration menu or help.
• When operating functions other than the Wireless Mouse function
(such as adjusting the volume).
However, when using the E-Zoom or Pointer function, the page up
or down function is available.
Saving a User's Logo
You can save the image that is currently being projected as a User's Logo.
You can use the registered user's logo as a display when projection starts or
no image signal is being input.
s Extended - Display p.103
a
a
Once a User Logo has been saved, the logo cannot be returned to the
factory default.
Project the image you want to save as the User's Logo, and then
press the [Menu] button.
s "Using the Configuration Menu" p.95
Using Remote Control
b
Select User's Logo from Extended.
Using the Control Panel
Projection Functions
72
d
Move the box to select the part of the image to use as the User's
Logo.
You can perform the same operations from the projector's control
panel.
Remote control
a
• When User's Logo Protect from Password Protect is set to
On, a message is displayed and the User's Logo cannot be
changed. You can make changes after setting User's Logo
Protect to Off.
s "Managing Users (Password Protect)" p.80
• If User's Logo is selected when Keystone, E-Zoom, Aspect, or
Adjust Zoom is being performed, the function currently being
performed is cancelled.
c
When the message "Choose this image as the User's Logo?" is
displayed, select Yes.
a
When you press the [ ] button on the remote control or the
control panel, the screen size may change depending on the
signal to match the actual resolution of the image signal.
a
e
You can save at 400x300 dots in size.
When you press the [ ] button and the message "Select this
image?" is displayed, select Yes.
Projection Functions
f
Select the zoom factor from the zoom setting screen.
73
a
a
When a User Pattern is saved, the previous User Pattern is erased.
Project the image you want to use as the User Pattern, and then
press the [Menu] button.
s "Using the Configuration Menu" p.95
Using Remote Control
g
When the message "Save this image as the User's Logo?" is
displayed, select Yes.
The image is saved. After the image has been saved, the message
"Completed." is displayed.
a
b
Select Pattern from Settings.
c
Select User Pattern.
• When a User's Logo is saved, the previous User's Logo is
erased.
• It takes a while to save. Do not operate the projector or any
connected equipment while it is saving, otherwise
malfunctions may occur.
Saving User Pattern
There are four types of patterns registered to the projector, such as ruled
lines and grid patterns.
s Settings - Pattern - Pattern Type p.101
You can also save the image that is currently being projected as a User
Pattern.
Using the Control Panel
Projection Functions
74
Projecting Without a Computer (Slideshow)
By connecting a USB storage device such as a USB memory or a USB hard
disk to the projector, you can project the files stored on the device without
using a computer. This function is called Slideshow.
a
• You may not be able to use USB storage devices that incorporate
security functions.
• You cannot correct keystone distortion while projecting a Slideshow,
even if you press the [w] and [v] buttons on the control panel.
Specifications for files that can be projected using Slideshow
a
If User Pattern is selected when Keystone, E-Zoom, Aspect,
Adjust Zoom, or Image Shift are being performed, the function
currently being performed is temporarily canceled.
d
When "Do you want to use the currently projected image as the
User Pattern?" is displayed, select Yes.
e
When you press the [ ] button, the message "Do you save this
image as the User Pattern?" is displayed. Select Yes.
The image is saved. After the image has been saved, the message
"The User Pattern setting is complete." is displayed.
a
• Once a User Pattern has been saved, User Pattern cannot be
returned to the factory default.
• It takes a while to save a User Pattern. Do not operate the
projector or any connected equipment while saving the user
pattern, otherwise malfunctions may occur.
Type
File Type (Ex‐
tension)
Notes
Image
.jpg
The following cannot be projected.
- CMYK color mode format
- Progressive format
- Images with a resolution greater than 8192x8192
Due to the characteristics of JPEG files, images may
not be projected clearly if the compression ratio is
too high.
.bmp
Cannot project images with a resolution greater
than 1280x800.
.gif
• Cannot project images with a resolution greater
than 1280x800.
• Cannot project animated GIFs.
.png
Cannot project images with a resolution greater
than 1280x800.
Projection Functions
a
• When connecting and using a USB-compatible hard disk, make sure
you connect the AC adaptor supplied with the hard disk.
• The projector does not support some file systems, so use media that
has been formatted in Windows.
• Format the media in FAT16/32.
Slideshow examples
75
Starting Slideshow
a
b
Change the source to USB.
s "Switching to the Target Image Using the Remote Control"
p.41
Connect the USB storage device or digital camera to the projector.
s "Connecting USB Devices" p.31
Slideshow starts and the file list screen is displayed.
Projecting images stored on USB storage
• JPEG files are displayed as thumbnails (file contents are displayed
as small images).
• Other files or folders are displayed as icons as shown in the
following table.
Icon
File
Icon
File
JPEG files*
BMP files
GIF files
PNG files
s "Projecting the selected image" p.77
s "Projecting image files in a folder in sequence (Slideshow)" p.78
Slideshow operating methods
Although the following steps are explained based on the remote control,
you can perform the same operations from the control panel.
*
When it cannot be displayed as a thumbnail, it is displayed as an icon.
Projection Functions
a
76
• You can also insert a memory card into a USB card reader and then
connect the reader to the projector. However, some commercially
available USB card readers may not be compatible with the
projector.
• If the following screen (Select Drive screen) is displayed, use the
[
], [
], [ ], and [ ] buttons to select the drive you want to
use, and then press the [
] button.
a
If not all of the files and folders are displayed on the current
screen, press the []] button on the remote control, or position
the cursor on Next Page at the bottom of the screen and press
the [ ] button.
To return to the previous screen, press the [[] button on the
remote control, or position the cursor on Previous Page at the
top of the screen and press the [ ] button.
• You can display the Select Drive screen by positioning the cursor on
Select Drive at the top of the file list screen, and then press the [ ]
button.
Projecting images
a
Use the [
], [
], [ ], and [ ] buttons to select the file or
folder you want to project.
b
Press the [
] button.
The selected image is displayed.
When a folder is selected, the files in the selected folder are
displayed. To return to the screen which was displayed before
opening the folder, position the cursor on Back to Top and press the
[ ] button.
Rotating images
You can rotate the played images in 90˚ increments. The rotating function
is also available during Slideshow.
Projection Functions
a
b
77
a
Play images, or run Slideshow.
While projecting, press the [
] or [
] button.
Start Slideshow.
The file list screen is displayed.
s "Starting Slideshow" p.75
b
Press the [
], [
], [ ], and [ ] buttons to select the image file
you want to project.
Stopping Slideshow
To close Slideshow, disconnect the USB device from the USB port on the
projector. For devices such as digital cameras or hard disks, turn off the
device and then remove it from the projector.
c
Press the [
] button.
The image is displayed.
Projecting the selected image
Attention
Do not disconnect the USB storage device while it is being accessed.
Slideshow may not operate correctly.
a
Press the [ ][ ] buttons to move to the next or previous
image file.
Projection Functions
d
78
screen, projection starts again from the beginning when it reaches
the end.
Press the [Esc] button to return to the file list screen.
s "Image file display settings and Slideshow operation settings"
p.78
Projecting image files in a folder in sequence (Slideshow)
You can proceed to the next screen, return to the previous screen, or
stop playback while projecting a Slideshow.
You can project the image files in a folder in sequence, one at a time. This
function is called Slideshow. Use the following procedure to run
Slideshow.
a
To change files automatically when you run Slideshow, set Screen
Switching Time from Option in Slideshow to anything other than No.
The default setting is 3 seconds.
a
s "Image file display settings and Slideshow operation settings"
p.78
a
b
c
If Screen Switching Time on the Option screen is set to No, files do
not change automatically when you select Play Slideshow. Press the
[ ] button, the [
] button, or the []] button to continue to the next
file.
You can use the following functions when projecting an image file with
Slideshow.
Start Slideshow.
The file list screen is displayed.
s "Starting Slideshow" p.75
• Freeze
s "Freezing the Image (Freeze)" p.67
Use the [
• A/V Mute
s "Hiding the Image and Sound Temporarily (A/V Mute)" p.67
], [
], [ ], and [ ] buttons to position the cursor
on the folder you want to run the Slideshow, and then press the
[ ] button.
Select Slideshow at the bottom of the file list screen, and then
press the [ ] button.
Slideshow starts, and the image files in the folder are automatically
projected in sequence, one at a time.
When the last file is projected, the file list is displayed again
automatically. If you set Continuous Play to On in the Option
• E-Zoom
s "Enlarging Part of the Image (E-Zoom)" p.69
Image file display settings and Slideshow operation settings
You can set the file display order and Slideshow operations on the Option
screen.
a
Press the [
], [
], [ ] and [ ] buttons to position the cursor
over the folder where you want to set display conditions, and then
press the [Esc] button. Select Option from the submenu displayed,
then press the [ ] button.
Projection Functions
b
When the following Option screen is displayed, set each of the
items.
Enable the settings by positioning the cursor on the target item and
pressing the [ ] button.
The following table shows the details for each item.
Display Order
You can select to display the files in Name Order or Date
Order.
Sort Order
You can select to sort the files In Ascending or In
Descending order.
Continuous
Play
You can set whether to repeat the Slideshow.
Screen Switch‐
ing Time
You can set the time for a single file to be displayed in Play
Slideshow. You can set a time between No (0) to 60
Seconds. When you set No, auto play is disabled.
Effect
You can set the screen effects when changing slides.
79
c
Use the [
], [
], [ ], and [ ] buttons to position the cursor
over OK, and then press the [
] button.
The settings are applied.
If you do not want to apply the settings, position the cursor on
Cancel, and then press the [ ] button.
Security Functions
The projector has the following enhanced security functions.
• Password Protect
You can limit who can use the projector.
• Control Panel Lock
You can prevent people changing the settings on the projector without
permission.
s "Restricting Operation (Control Panel Lock)" p.82
• Anti-Theft Lock
The projector is equipped with the following anti-theft security device.
s "Anti-Theft Lock" p.83
80
• User's Logo Protect
Even if someone tries to change the User's Logo set by the owner of the
projector, it cannot be changed. When User's Logo Protect is set to On,
the following setting changes for the User's Logo are prohibited.
• Capturing a User's Logo
• Setting Display Background, Startup Screen, or A/V Mute from
Display
s Extended - Display p.103
• Network Protect
When Network Protect is set to On, changing the settings for Network is
prohibited.
s "Network Menu" p.105
Managing Users (Password Protect)
When Password Protect is activated, people who do not know the password
cannot use the projector to project images even if the projector power is on.
Furthermore, the user's logo that is displayed when you turn on the
projector cannot be changed. This acts as an anti-theft device as the
projector cannot be used even if it is stolen. At the time of purchase,
Password Protect is not activated.
Setting Password Protect
Use the following procedure to set Password Protect.
a
During projection, hold down the [Freeze] button for about five
seconds.
The Password Protect setting menu is displayed.
Remote control
Kinds of Password Protect
The following three kinds of Password Protect settings can be made
according to how the projector is being used.
• Power On Protect
When Power On Protect is On, you need to enter a preset password after
the projector is plugged in and turned on (this also applies to Direct
Power On). If the correct password is not entered, projection does not
start.
Security Functions
a
81
• If Password Protect is already activated, you must enter the
password.
If the password is entered correctly, the Password Protect
setting menu is displayed.
s "Entering the Password" p.81
(3)
While holding down the [Num] button, enter a four digit number using
the numeric buttons. The number entered is displayed as "* * * *". When
you enter the fourth digit, the confirmation screen is displayed.
Remote control
• When the password is set, stick the supplied password protect
sticker in a visible position on the projector as a further theft
deterrent.
b
Select the type of Password Protect you want to set, and then
press the [ ] button.
(4)
Re-enter the password.
The message "Password accepted." is displayed.
If you enter the password incorrectly, a message is displayed prompting
you to re-enter the password.
Entering the Password
When the password entry screen is displayed, enter the password using the
remote control.
c
Select On, and then press the [
d
Set the password.
] button.
Press the [Esc] button, the screen displayed in step 2 is displayed
again.
(1)
Select Password, and then press the [
(2)
When the message "Change the password?" is displayed, select Yes and
then press the [ ] button. The default password is set to "0000". Change
this to your own desired Password. If you select No, the screen displayed
in step 2 is displayed again.
] button.
While holding down the [Num] button, enter the password by pressing the
numeric buttons.
Security Functions
When you enter the correct password, Password Protect is temporarily
released.
Attention
• If an incorrect password is entered three times in succession, the message
"The projector's operation will be locked." is displayed for approximately five
minutes, and then the projector switches to standby mode. If this happens,
disconnect the power plug from the electrical outlet and then reinsert it and
turn the projector's power back on. The projector displays the password entry
screen again so that you can enter the correct password.
82
This is useful at events or shows when you want to deactivate all buttons
during projection or at schools when you want to limit button operation.
The projector can still be operated using the remote control.
a
Press the [Menu] button while projecting.
s "Using the Configuration Menu" p.95
Using Remote Control
Using the Control Panel
• If you have forgotten the password, make a note of the "Request Code:
xxxxx" number that appears on the screen and contact the nearest address
provided in the Epson Projector Contact List.
s Epson Projector Contact List
• If you continue to repeat the above operation and input the wrong Password
30 times in succession, the following message is displayed and the projector
does not accept any more Password entries. "The projector's operation will be
locked. Contact Epson as described in your documentation."
s Epson Projector Contact List
b
Select Control Panel Lock from Settings.
c
Select either Full Lock or Partial Lock according to your purpose.
Restricting Operation (Control Panel Lock)
Do one of the following to lock the operation buttons on the control
panel.
• Full Lock
All of the buttons on the control panel are locked. You cannot perform
any operations from the control panel, including turning the power on or
off.
• Partial Lock
All of the buttons on the control panel, except for the [t] button, are
locked.
Security Functions
83
Anti-Theft Lock
The projector is equipped with the following types of anti-theft security
devices.
d
Select Yes when the confirmation message is displayed.
The control panel buttons are locked according to the setting you
chose.
a
You can release the control panel lock by one of the following
two methods.
• Select Off from Control Panel Lock.
s Settings - Control Panel Lock p.101
• Press and hold down the [ ] button on the control panel for
about seven seconds, a message is displayed and the lock is
released.
• Security slot
The security slot is compatible with the Microsaver Security System
manufactured by Kensington.
See the following for more details on the Microsaver Security System.
s http://www.kensington.com/
• Security cable installation point
A commercially available theft-prevention wire lock can be passed
through the installation point to secure the projector to a desk or pillar.
Installing the wire lock
Pass an anti-theft wire lock through the installation point.
See the documentation supplied with the wire lock for locking instructions.
Monitoring and Controlling
About EasyMP Monitor
EasyMP Monitor lets you carry out operations such as checking the status
of multiple Epson projectors that are connected to a network at a computer
monitor, and controlling the projectors from the computer.
You can download EasyMP Monitor from the following Web site.
http://www.epson.com
The following provides brief descriptions of the monitoring and control
functions that can be carried out using EasyMP Monitor.
• Registering projectors for monitoring and control
Projectors on the network can be searched for automatically, and you can
then select which projectors you want to register from the projectors that
are detected.
You can register target projectors by entering their IP addresses.
• Registered projectors can also be assigned to groups so that they can
be monitored and controlled in groups.
• Monitoring the status of registered projectors
You can check the power status (ON/OFF) for projectors and problems or
warnings that require attention by using the icons.
You can select groups of projectors or a single projector and then check
the cumulative lamp operating time or information such as input sources,
problems, and warnings for the projectors.
• Controlling registered projectors
Projectors can be selected in groups or as single projectors, and you can
then carry out operations for the selected projectors such as turning the
power on and off and switching their input sources.
You can use Web Control functions to change the settings in the
projector's configuration menu.
If there are certain control actions which are carried out regularly at
particular times or on particular days, you can use Timer Settings to
register timer settings.
84
• Mail Notification settings
You can set e-mail addresses to which notifications are sent if a status
that requires attention, such as a problem, occurs with a registered
projector.
• Sending messages to registered projectors
You can use the Message Broadcasting plugin for EasyMP Monitor to
send JPEG files to registered projectors.
Download the Message Broadcasting plugin from the Web site address
provided at the beginning of this chapter.
Changing Settings Using a Web Browser (Web
Control)
By using the Web browser of a computer connected to the projector on a
network, you can set the projector's functions and control the projector.
This function allows you to perform setup and control operations remotely.
In addition, since you can use the computer's keyboard, entering characters
required for the setup is easier.
Use Microsoft Internet Explorer 6.0 or later as the Web browser. Use Safari
for Mac OS X.
a
If you set Standby Mode to Communication On, you can use a Web
browser to make settings and perform control even if the projector is
in standby mode (when the power is off).
s Extended - Standby Setup - Standby Mode p.103
Projector setup
In a Web browser, you can set items that are usually set in the projector's
Configuration menu. The settings are reflected in the Configuration menu.
There are also items that can only be set in a Web browser.
Monitoring and Controlling
Items in the Configuration menu that cannot be set by a Web browser
• Settings menu - Keystone - Quick Corner
• Settings menu - Image Shift
• Settings menu - Pointer Shape
• Settings menu - Pattern (except Pattern Type)
• Settings menu - User Button
• Extended menu - User's Logo
• Extended menu - USB Type B
• Extended menu - Easy Interactive Function
• Extended menu - Language
• Extended menu - Operation - High Altitude Mode
• Reset menu - Reset All and Reset Lamp Hours
The settings for items on each menu are the same as the projector's
Configuration menu.
s "Configuration Menu" p.94
Items that can only be set with a Web browser
• SNMP Community Name
• Monitor Password
Displaying the Web Control screen
Use the following procedure to display the Web Control screen.
85
b
Enter the IP address of the projector in the address input box of
the Web browser, and press the Enter key on the computer's
keyboard.
c
The user ID and password entry screen is displayed.
Enter "EPSONWEB" as the user ID.
The default password is "admin".
a
• Enter the user ID even if the password setting is disabled. The
user ID cannot be changed.
• You can change the password from Basic - Web Control
Password in the Network menu under the Configuration
menu.
s "Basic menu" p.107
Displaying the Web Remote screen
The Web Remote function allows you to perform projector remote control
operations with a Web browser.
a
b
Display the Web Control screen.
c
The Web Remote screen is displayed.
Click Web Remote.
Make sure the computer and projector are connected to the network. Use
Advanced when connecting via a Wireless LAN.
a
a
If your Web browser is set up to connect via a proxy server, the Web
Control screen cannot be displayed. To display Web Control, you need
to make settings so that a proxy server is not used for a connection.
Start a Web browser on the computer.
Monitoring and Controlling
86
Name
F [Page] buttons
[Up] [Down]
Function
Changes pages in files such as PowerPoint files when using
the following projection methods.
• When using the Wireless Mouse function
s "Using the Remote Control to Operate the
Mouse Pointer (Wireless Mouse)" p.70
• When using USB Display
s "Projecting with USB Display" p.41
• When connecting to a network
When projecting images using Slideshow, pressing these
buttons displays the previous/next image file.
Name
G [Source Search]
button
Switches to the image from the input port where video
signals are being input.
s "Automatically Detect Input Signals and Change the
Projected Image (Source Search)" p.40
H [LAN] button
Changes to the images projected with EasyMP Network
Projection. When projecting using the optional Quick
Wireless Connection USB Key, this button switches to
that image.
s "Switching to the Target Image Using the Remote
Control" p.41
I [USB] button
Each time the button is pressed, it cycles through the
following images:
• USB Display
• Images from the device connected to the USB-A port
s "Switching to the Target Image Using the Remote
Control" p.41
J [Volume] buttons
[a][b]
[a] Decreases the volume.
[b] Increases the volume.
s "Adjusting the Volume" p.50
Function
A [t] button
Turns the projector power on or off.
s "From Installation to Projection" p.39
B [Computer] button
Each time the button is pressed, it cycles through the
following images:
• Computer1 port
• Computer2 port
C [Video] button
Each time the button is pressed, it cycles through the
following images:
• S-Video port
• Video port
• HDMI port
D [Freeze] button
Pauses or resumes image playback.
s "Freezing the Image (Freeze)" p.67
E [A/V Mute] button
Turns the video and audio on or off.
s "Hiding the Image and Sound Temporarily (A/V
Mute)" p.67
Monitoring and Controlling
Using the Mail Notification Function to Report
Problems
When you set Mail Notification, notification messages are sent to the preset
email addresses when a problem or warning occurs with a projector. This
will enable the operator to be notified of problems with projectors even at
locations away from the projectors.
s Network - Mail - Mail Notification p.111
a
87
The details of the problem are listed line by line. The main message
contents are listed below.
• Internal error
• Fan related error
• Sensor error
• Lamp timer failure
• Lamp out
• Up to a maximum of three notification destinations (addresses) can
be registered, and notification messages can be sent to all three
destinations at once.
• Internal temperature error
• If a projector develops a critical problem and suddenly stops
working, it may not be able to send a message notifying an operator
of the problem.
• Lamp replacement notification
• Controlling is possible if Standby Mode is set to Communication
On, even if the projector is in standby state (when the power is
off).
s Extended - Standby Setup - Standby Mode p.103
• High-speed cooling in progress
• No-signal
No Signal is input to the projector. Check the connection status or check
that the power for the signal source is turned on.
• Auto Iris Error
• Power Err. (Ballast)
• Obstacle Detection Error
Reading Error Notification Mail
When the Mail Notification function is set to On and a problem or warning
occurs in the projector, the following email will be sent.
See the following to deal with problems or warnings.
s "Reading the Indicators" p.118
Sender: Email Address 1
Subject: EPSON Projector
Line 1: The name of the projector where the problem occurred
Line 2: The IP address set for the projector where the problem has
occurred.
Line 3 and on: Details of the problem
Management Using SNMP
By setting SNMP to On in the Configuration menu, notification messages
are sent to the specified computer when a problem or warning occurs. This
will enable the operator to be notified of problems with projectors even at
locations away from the projectors.
s Network - Others - SNMP p.113
Monitoring and Controlling
a
88
Item
• SNMP should be managed by a network administrator or someone
who is familiar with the network.
• To use the SNMP function to monitor the projector, you need to
install the SNMP manager program on your computer.
• The managing function using SNMP cannot be used via wireless
LAN in Quick connection mode.
• Up to two destination IP addresses can be saved.
ESC/VP21 Commands
You can control the projector from an external device using ESC/VP21.
A/V Mute ON/OFF
When the power ON command is transmitted to the projector, the power
turns on and it enters warm-up mode. When the projector's power has
turned on, a colon ":" (3Ah) is returned.
When a command is input, the projector executes the command and
returns a ":", and then accepts the next command.
SOURCE 21
Component
SOURCE 24
HDMI
SOURCE 30
Video
SOURCE 41
S-Video
SOURCE 42
USB Display
SOURCE 51
USB
SOURCE 52
LAN
SOURCE 53
On
MUTE ON
Off
MUTE OFF
For more details, contact your local dealer or the nearest address provided
in the Epson Projector Contact List.
s Epson Projector Contact List
If the command being processed terminates abnormally, an error message is
output and a ":" is returned.
Cable layouts
The main contents are listed below.
Serial connection
Item
Signal selection
RGB
Add a Carriage Return (CR) code (0Dh) to the end of each command and
transmit.
Command list
Power ON/OFF
Command
Command
On
PWR ON
Off
PWR OFF
Computer1
Computer2
Auto
SOURCE 1F
RGB
SOURCE 11
Component
SOURCE 14
Auto
SOURCE 2F
• Connector shape: D-Sub 9-pin (male)
Monitoring and Controlling
89
• Projector input port name: RS-232C
<At the projector>
<At the computer>
About PJLink
PJLink Class1 was established by the JBMIA (Japan Business Machine and
Information System Industries Association) as a standard protocol for
controlling network-compatible projector's as part of their efforts to
standardize projector control protocols.
The projector complies with the PJLink Class1 standard established by the
JBMIA.
You need to make network settings before you can use PJLink. See the
following for more information on network settings.
s "Network Menu" p.105
<At the projector>
(PC serial cable)
<At the computer>
It complies with all commands except for the following commands defined
by PJLink Class1, and agreement was confirmed by the PJLink standard
adaptability verification.
URL:http://pjlink.jbmia.or.jp/english/
• Non-compatible commands
Function
Signal Name
Function
GND
Signal wire ground
TD
Transmit data
RD
Receive data
Mute settings
PJLink Command
Image muting set
AVMT 11
Audio muting set
AVMT 21
• Input names defined by PJLink and corresponding projector sources
Source
Communications protocol
•
•
•
•
•
Default baud rate setting: 9600 bps
Data length: 8 bit
Parity: None
Stop-bit: 1 bit
Flow control: None
PJLink Command
Computer1
INPT 11
Computer2
INPT 12
Video
INPT 21
S-Video
INPT 22
HDMI
INPT 32
USB
INPT 41
Monitoring and Controlling
90
Source
PJLink Command
LAN
INPT 52
USB Display
INPT 53
• Monitoring and control with application software
You can use Crestron RoomView Express or Crestron RoomView
Server Edition provided by Crestron to monitor devices in the system,
to communicate with the help desk, and to send emergency messages. See
the following Web site for details.
http://www.crestron.com/getroomview
®
• Manufacturer name displayed for "Manufacture name information query"
®
®
EPSON
This manual describes how to perform operations on your computer using
a Web browser.
• Model name displayed for "Product name information query"
EB-485Wi/EB-485WT/EB-CU610Wi/BrightLink 485Wi
EB-485W/EB-CU610W/PowerLite 485W
EB-480i/EB-480T/EB-CU610Xi/BrightLink 480i
EB-480/EB-CU610X/PowerLite 480
EB-475Wi/EB-475WT/EB-CU600Wi/BrightLink 475Wi
EB-475W/EB-CU600W/PowerLite 475W
EB-470/EB-CU600X/PowerLite 470
a
®
About Crestron RoomView
®
Crestron RoomView is an integrated control system provided by
Crestron . It can be used to monitor and control multiple devices
connected on a network.
®
The projector supports the control protocol, and can therefore be used in a
system built with Crestron RoomView .
®
®
®
Visit the Crestron Web site for details on Crestron RoomView . (Only
English-language displays are supported.)
http://www.crestron.com
®
The following provides an overview of Crestron RoomView .
• Remote operation using a Web browser
You can operate a projector from your computer just like using a remote
control.
• You can only enter single-byte alphanumeric characters and symbols.
• The following functions cannot be used while using Crestron
RoomView .
s "Changing Settings Using a Web Browser (Web Control)"
p.84
Message Broadcasting (EasyMP Monitor plug-in)
®
• Controlling is possible if Standby Mode is set to Communication
On, even if the projector is in standby state (when the power is
off).
s Extended - Standby Setup - Standby Mode p.103
Operating a projector from your computer
Displaying the operation window
Check the following before carrying out any operations.
• Make sure the computer and projector are connected to the network.
When communicating with a wireless LAN, connect in Advanced
connection mode.
s "Wireless LAN menu" p.108
• Set Crestron RoomView to On from the Network menu.
s Network - Others - Crestron RoomView p.113
Monitoring and Controlling
a
b
91
Start a Web browser on the computer.
Enter the IP address of the projector in the address field of the
Web browser, and press the Enter key on the keyboard.
Button
Function
Turns the video and audio on or off.
s "Hiding the Image and Sound Temporarily (A/V
Mute)" p.67
A/V Mute
The operation window is displayed.
B Switch to the image from the selected input source. To display input sources that
are not shown on the screen, click (a) or (b) to scroll up or down. The current video
signal input source is displayed in blue.
You can change the source name if necessary.
Using the operation window
C You can perform the following operations when you click the buttons. To display
buttons that are not shown on the screen, click (c) or (d) to scroll left or right.
Button
Function
Freeze
Pauses or resumes image playback.
s "Freezing the Image (Freeze)" p.67
Contrast
You can adjust the difference between light and dark in
the images.
Brightness
You can adjust the image brightness.
Color
You can adjust the color saturation for the images.
Sharpness
You can adjust the image sharpness.
Zoom
Click the [z] button to enlarge the image without
changing the projection size. Click the [x] button to
reduce an image that was enlarged with the [z] button.
Click the [ ], [ ], [ ], or [ ] button to change the
position of an enlarged image.
s "Enlarging Part of the Image (E-Zoom)" p.69
A You can perform the following operations when you click the buttons.
Button
Function
Power
Turns the projector power on or off.
Vol-/Vol+
Adjusts the volume.
D [
], [
], [
], and [
] buttons have the same effects as [
], [
], [ ],
and [ ] buttons on the remote control respectively. You can perform the
following operations when you click the other buttons.
Monitoring and Controlling
Button
92
Function
OK
Performs the same operation as the [
remote control.
s "Remote Control" p.16
Menu
Displays and closes the Configuration menu.
Auto
If clicked while projecting analog RGB signals from
Computer1 port or Computer2 port, automatically
optimizes the image by adjusting the Tracking, Sync.,
and Position.
Search
Switches to the image from the input port where video
signals are being input.
s "Automatically Detect Input Signals and Change the
Projected Image (Source Search)" p.40
Esc
Performs the same operation as the [Esc] button on the
remote control.
s "Remote Control" p.16
] button on the
E You can perform the following operations when you click the tabs.
Tab
®
B Projector
The following items can be set.
Item
Function
Contact IT Help
Displays the Help Desk window. Used to send messages
to, and receive messages from, the administrator using
Crestron RoomView Express.
Info
Displays information on the projector that is currently
connected.
Tools
A Crestron Control
Make settings for Crestron central controllers.
Projector Name
Enter a name to differentiate the projector that is
currently connected from other projectors on the
network. (The name can contain up to 15 single-byte
alphanumeric characters.)
Location
Enter an installation location name for the projector
that is currently connected on the network. (The name
can contain up to 32 single-byte alphanumeric
characters and symbols.)
Assigned To
Enter a user name for the projector. (The name can
contain up to 32 single-byte alphanumeric characters
and symbols.)
®
Changes settings in the projector that is currently
connected. See the next section.
Using the tools window
The following window is displayed when you click the Tools tab on the
operation window. You can use this window to change settings in the
projector that is currently connected.
Function
Monitoring and Controlling
Item
93
Function
DHCP
Select the Enabled check box to use DHCP. You cannot
enter an IP address if DHCP is enabled.
IP Address
Enter the IP address to assign to the currently connected
projector.
Subnet Mask
Enter a subnet mask for the currently connected
projector.
Default Gateway
Enter the gateway address for the currently connected
projector.
Send
Click this button to confirm the changes made to the
Projector.
C Admin Password
Select the Enabled check box to require a password to open the Tools window.
The following items can be set.
Item
Function
New Password
Enter the new password when changing the password to
open the Tools window. (The name can contain up to 26
single-byte alphanumeric characters.)
Confirm
Enter the same password as you entered in New
Password. If the passwords are not the same, an error is
displayed.
Send
Click this button to confirm the changes made to the
Admin Password.
D User Password
Select the Enabled check box to require a password to open the operation window
on the computer.
The following items can be set.
Item
Function
New Password
Enter the new password when changing the password to
open the operation window. (Up to 26 single-byte
alphanumerical characters)
Confirm
Enter the same password as you entered in New
Password. If the passwords are not the same, an error is
displayed.
Send
Click this button to confirm the changes made to the
User Password.
Configuration Menu
This chapter explains how to use the Configuration menu and its functions.
Using the Configuration Menu
This section explains how to use the Configuration menu.
Although steps are explained using the remote control as an example, you
can perform the same operations from the control panel. Check the guide
under the menu for the available buttons and their operations.
a
b
95
c
Select a submenu item.
d
Change settings.
e
Press the [Menu] button to finish making settings.
Display the Configuration menu screen.
Select a top menu item.
List of Functions
96
Top Menu Name
Configuration Menu Table
Submenu Name
Video Signal
Auto, NTSC, NTSC4.43, PAL,
M-PAL, N-PAL, PAL60, and
SECAM
Aspect
Normal, Auto, 4:3, 16:9, Full,
Zoom, and Native
Overscan
Auto, Off, 4%, and 8%
Keystone
H/V-Keystone and Quick Corner
Zoom
0 (Wide) to 40 (Tele)
Settable items vary depending on the model being used and the image
signal and source being projected.
Top Menu Name
Image menu
s p.98
Signal menu
s p.99
Submenu Name
Color Mode
Items or Setting Values
Dynamic, Presentation, Theatre,
Photo, Sports, sRGB, Blackboard,
and Whiteboard
Settings menu
s p.101
Items or Setting Values
Brightness
-24 to 24
Contrast
-24 to 24
Image Shift
-
Color Saturation
-32 to 32
Control Panel Lock
Full Lock, Partial Lock, and Off
Tint
-32 to 32
Pointer Shape
Pointer 1, Pointer 2, Pointer 3
Sharpness
-5 to 5
Power Consumption
Normal and ECO
Abs. Color Temp.
5000K to 10000K
Volume
0 to 20
Color Adjustment
Red: -16 to 16
Green: -16 to 16
Blue: -16 to 16
Mic Input Level
0 to 5
Remote Receiver
Front/Rear, Front, Rear and Off
User Button
Power Consumption, Info,
Progressive, Test Pattern,
Resolution, Mic Input Level,
Pattern Display, Auto
Calibration
Pattern
Pattern Display, Pattern Type,
User Pattern, and Test Pattern
Display
Messages, Display Background,
Startup Screen, and A/V Mute
User's Logo
-
Projection
Front, Front/Upside Down, Rear,
Rear/Upside Down
Operation
Direct Power On, Sleep Mode,
Sleep Mode Timer, High
Altitude Mode, and Audio Input
Auto Iris
On and Off
Auto Setup
On and Off
Resolution
Auto, Wide, and Normal
Tracking
-
Sync.
-
Position
Up, Down, Left, and Right
Progressive
Off, Video, and Film/Auto
Noise Reduction
Off, NR1, and NR2
HDMI Video Range
Auto, Normal, and Expanded
Input Signal
Auto, RGB, and Component
Extended menu
s p.103
List of Functions
Top Menu Name
97
Submenu Name
Items or Setting Values
Standby Setup
Standby Mode, Standby
Microphone, Standby Audio
USB Type B
Easy Interactive Function, USB
Display/Easy Interactive
Function, Wireless Mouse/USB
Display
Easy Interactive Func‐ Auto Calibration, Manual
tion
Calibration, Use Source, Number
of Pen Users, Pen Operation
Mode, Enable Right Click,
Advanced
Info menu
s p.114
Reset menu
s p.115
*
Network menu
Top Menu Name
Basic menu
s p.107
Wireless LAN menu
s p.108
Submenu Name
Items or Setting Values
Projector Name
-
PJLink Password
-
Web Control Password
-
Projector Keyword
On and Off
Wireless LAN Power
On and Off
Connection Mode
Quick and Advanced
Channel
1ch, 6ch, and 11ch
Language
15 or 35 languages*
Wireless LAN Sys.
802.11b/g and 802.11b/g/n
Lamp Hours
-
SSID Auto Setting
On and Off
Source
-
SSID
-
Input Signal
-
IP Settings
Resolution
-
DHCP, IP Address, Subnet Mask,
and Gateway Address
Video Signal
-
SSID Display
On and Off
Refresh Rate
-
IP Address Display
On and Off
Sync Info
-
Security
No, WEP, WPA-PSK, and WPA2PSK
Status
-
WEP Encryption
128Bit and 64Bit
Serial Number
-
Format
ASCII and HEX
Event ID
-
Key ID
1, 2, 3, 4
Reset All
-
Reset Lamp Hours
-
Encryption Key 1, En‐ cryption Key 2, Encryp‐
tion Key 3, and Encryp‐
tion Key 4
Security menu
s p.109
The number of supported languages differs depending on the region where the
projector is used.
Wired LAN menu
s p.111
Authentication Type
Open and Shared
PSK
-
IP Settings
DHCP, IP Address, Subnet Mask,
and Gateway Address
List of Functions
Top Menu Name
Mail menu
s p.111
98
Submenu Name
Items or Setting Values
IP Address Display
On and Off
Mail Notification
On and Off
SMTP Server
-
Port Number
-
s "Automatically Detect Input Signals and Change the Projected Image
(Source Search)" p.40
Address 1 Setting, Ad‐ dress 2 Setting, and Ad‐
dress 3 Setting
Others menu
s p.113
SNMP
On and Off
Trap IP Address 1 and
Trap IP Address 2
-
Priority Gateway
Wired LAN and Wireless LAN
AMX Device Discovery On and Off
Crestron RoomView
On and Off
Bonjour
On and Off
Sub-menu
Color Mode
You can select the quality of the image to suit your surroundings.
s "Selecting the Projection Quality (Selecting Color Mode)"
p.51
Brightness
You can adjust the image brightness.
Contrast
You can adjust the difference between light and dark in the
images.
Color Saturation
(Adjustment is only possible when component video, composite
video, or S-video images are being input.)
You can adjust the color saturation for the images.
Tint
(Adjustment is possible when component video signals are being
input. Composite video and S-video input signals can only be
adjusted when they are NTSC video signals.)
You can adjust the image tint.
Sharpness
You can adjust the image sharpness.
Image Menu
Settable items vary depending on the image signal and source currently
being projected. Setting details are saved for each image signal.
Function
List of Functions
99
Sub-menu
Function
Abs. Color Temp.
(This item cannot be selected if Color Mode is set to sRGBg.)
You can adjust the overall tint of the image. You can adjust tints
in 10 stages from 5000 K to 10000 K. The image is tinted blue
when a high value is selected and tinted red when a low value is
selected.
Color Adjust‐
ment
(This item cannot be selected if Color Mode is set to sRGBg.)
You can adjust the color strength for Red, Green, and Blue
individually.
Auto Iris
(This item can be set only if Color Mode is set to Dynamic or
Theatre.)
Set to On to adjust the iris to obtain the optimum light for images
being projected.
The setting is stored for each Color Mode.
s "Setting Auto Iris" p.52
Reset
You can reset all adjustment values for the Image menu to their
default settings. See the following to return all menu items to
their default settings.
s "Reset Menu" p.115
Signal Menu
Settable items vary depending on the image signal and source currently
being projected. Setting details are saved for each image signal.
You cannot make settings on the Signal menu when the source is USB
Display, USB, or LAN.
s "Automatically Detect Input Signals and Change the Projected Image
(Source Search)" p.40
Sub-menu
Auto Setup
Function
(Only available when analog RGB computer signals are being
input.)
Set to On to automatically adjust Tracking, Sync., and Position to
the optimum state when the input signal changes.
List of Functions
Sub-menu
100
Function
Sub-menu
Function
Resolution
(Only available when analog RGB computer signals are being
input.)
Set to Auto to automatically identify the resolution of the input
signal. If images are not projected correctly when set to Auto, for
example if some of the image is missing, adjust to Wide for wide
screens, or set to Normal for 4:3 or 5:4 screens depending on the
connected computer.
Noise Reduction
(This cannot be set when a digital RGB signal is input, or when an
interlace signal is being displayed when Progressive is set to
Off.)
Smoothes out rough images. There are two modes. Select your
favorite setting. It is recommended that this is set to Off when
viewing image sources in which noise is very low, such as for
DVDs.
Tracking
(Only available when analog RGB computer signals are being
input.)
You can adjust computer images when vertical stripes appear in
the images.
HDMI Video
Range
When the projector's HDMI port is connected to a DVD player,
the projector's video range is set according to the DVD player's
video range setting.
Input Signal
You can select the input signal from the Computer1 port or the
Computer2 port.
If set to Auto, the input signal is set automatically according to
the connected equipment.
If colors do not appear correctly when set to Auto, select the
appropriate signal according to the connected equipment.
Video Signal
You can select the input signal from the S-Video port or the
Video port. If set to Auto, video signals are recognized
automatically. If interference appears in the image or a problem
occurs such as no image is being projected when set to Auto,
select the appropriate signal according to the connected
equipment.
Aspect
You can set the aspect ratiog for projected images.
s "Changing the Aspect Ratio of the Projected Image" p.52
Overscan
(This setting can only be adjusted when component video or
RGB video signals are being input.)
Changes the output image ratio (the range of the projected
image). You can set the cropping range to Off, 4%, or 8%. When
the source is HDMI, Auto is available. When Auto is selected, it
automatically changes to Off or 8% according to the input signal.
Sync.
(Only available when analog RGB computer signals are being
input.)
You can adjust computer images when flickering, fuzziness, or
interference appear in the images.
Position
(This item cannot be set when the source is HDMI.)
You can adjust the display position up, down, left, and right when
a part of the image is missing so that all of the image is projected.
Progressive
(This setting can only be adjusted when composite video or svideo signals are being input. When component video or RGB
video signals are being input, this setting can only be adjusted if
the signals being input are interlaced signals (480i/576i/1080i).)
Interlaceg (i) signal is converted to Progressiveg (p). (IP
conversion)
Off: Ideal for images with a large amount of movement.
Video: Ideal for general video images.
Film/Auto: This is ideal for movie films, computer graphics, and
animation.