Cannon HENLEY 10476G Technical data

HENLEY
PROFESSIONAL 600
TRADITIONAL 600
Use and Installation Instructions
The cooker must be installed in accordance with the regulations in force
and only used in a well ventilated space.
Read these instructions prior to using the cooker and retain them for
future reference.
Part no. 195044776.02
CONTENTS
PAGE
Introduction
3
For Your Safety
4
Timer Operation
6
Hotplate
12
Grill
14
Ovens
15
Oven Cooking Chart
16
The “Slow Cook” Setting
18
Care and Cleaning
19
Something Wrong with your cooker?
21
Installation Instructions
23
Service Information
2
Back Cover
INTRODUCTION
To help you make the best use of your cooker, PLEASE READ THIS BOOKLET
CAREFULLY.
Your new cooker is guaranteed and will give lasting service. The guarantee is only
applicable if the cooker has been installed in accordance with the Installation
Instructions.
The cooker is designed specifically for domestic use and responsibility will not be
accepted for use in any other installation.
When first using the cooker ensure that the room is well ventilated (e.g. open a
window or use an extractor fan) and that persons who may be sensitive to the odour
avoid any fumes. It is suggested that any pets be removed from the room until the
smell has ceased. This odour is due to any temporary finish and also any moisture
absorbed by the insulation.
Our policy is one of continual improvement in design and development,
therefore strict accuracy of illustrations and descriptions cannot be
guaranteed.
This appliance conforms to the following EEC Directives:
Gas Appliances
90/396/EEC
Low Voltage Equipment
73/23/EEC
93/68/EEC
Electromagnetic Compatibility
89/336/EEC
92/31/EEC
93/68/EEC
3
FOR YOUR SAFETY
Please read the precautions below before using your cooker.
ALWAYS . . .
ALWAYS
make sure you understand the controls before using the cooker.
ALWAYS
check that all controls on the cooker are turned off after use.
ALWAYS
stand back when opening an oven door to allow heat to disperse.
ALWAYS
use dry, good quality oven gloves when removing items from the ovens.
ALWAYS
take care when removing items from the top oven/grill when the main
oven is on, as the contents may be hot.
ALWAYS
keep the oven and grill doors closed when the cooker is not in use.
ALWAYS
place pans centrally over the hotplate burners and position them so
that the handles cannot accidentally be caught or knocked or become
heated by other burners.
ALWAYS
keep the cooker clean, as a build up of grease or fat from cooking can
cause a fire.
ALWAYS
allow the cooker to cool before cleaning.
ALWAYS
follow the basic principles of food handling and hygiene to prevent the
possibility of bacterial growth.
ALWAYS
keep ventilation slots clear of obstructions.
ALWAYS
turn off the electricity supply before cleaning or replacing the oven lamp.
ALWAYS
refer servicing to CORGI registered appliance service engineers.
4
FOR YOUR SAFETY
NEVER . . .
NEVER
leave children unsupervised where the cooker is installed as all surfaces will
get hot during and after use.
NEVER
allow anyone to sit or stand on any part of the cooker.
NEVER
store items that children may attempt to reach above the cooker.
NEVER
heat up unopened food containers as pressure can build up causing the
container to burst.
NEVER
store chemicals, food stuffs, pressurised containers in or on the cooker, or in
cabinets immediately above or next to the cooker.
NEVER
fill a deep fat frying pan more than 1/3 full of oil, and never use a lid.
DO NOT LEAVE UNATTENDED WHILE COOKING.
NEVER
place flammable or plastic items on or near the hotplate.
NEVER
use proprietary spillage collectors on the hotplate.
NEVER
use the cooker as a room heater.
NEVER
dry clothes or place other times over or near to the hotplate or oven/grill
doors.
NEVER
wear garments with long flowing sleeves whilst cooking.
NOTE: The use of a gas cooking appliance results in the production of heat and
moisture in the room in which it is installed. Always ensure that the kitchen is well
ventilated; keep natural ventilation holes open or install a mechanical ventilation
device (mechanical extractor hood).
In particular when using more than one hotplate burner, open a window if a
mechanical ventilation device is not operating.
5
TIMER OPERATION
The timer offers you the following features:
1. Time of Day
2. Automatic Cooking
3. Minute Minder
AUTOMATIC COOKING
The main oven can be controlled automatically.
GUIDANCE ON AUTOMATIC COOKING
1. Select foods which will take the same time to cook.
2. Set the oven timer so that the food has just finished or is just about to finish
cooking on your return to the oven. This will ensure the food has not cooled down
and does not require reheating before serving.
3. Food should be as cold as possible when it goes into the oven, ideally straight
from the refrigerator. Frozen meat and poultry should be thawed thoroughly
before it is put in the oven.
4. Warm food should never be placed in the oven if there is to be a delay period. Stews
prepared by frying the meat and vegetables should be cooked as soon as possible.
5. Dishes containing left-over cooked poultry or meat, for example Shepherds Pie,
should not be cooked automatically if there is to be a delay period.
6. Stews and joints should be cooked by the long slow method, so that the delay
period is kept to a minimum.
7. On warm days, to prevent harmful bacterial growth in certain foods (ie poultry,
joints, etc) the delayed start should be kept to a minimum.
8. Wine or beer may ferment and cream may curdle during the delay period, so it is
best to add these ingredients just before serving.
9. Foods which discolour should be protected by coating in fat or tossing in water to
which lemon juice has been added, prior to placing food in the oven.
10. Dishes containing liquid should not be filled too full to prevent boiling over.
11. Food should be well sealed (but not airtight) in a container to prevent the loss of
liquid during cooking. Aluminium foil gives a good seal.
12. Ensure food is cooked thoroughly before serving.
6
TIMER OPERATION
CLOCKFACE
The timer incorporates a 24 hour clock.
Ensure the correct time of day is always set, before using your cooker.
SYMBOLS
A ‘bell’ symbol will light up when you select a Minute Minder Period and will
remain lit for the period set.
At the end of the Minute Minder Period, the timer will emit an audible tone and
the ‘bell’ symbol will disappear.
The ‘cookpot’ symbol will light up either:–
– When the timer is in manual mode, or
– During the actual Cook Period.
‘AUTO’ will light up:–
– When the timer is first turned on it will flash. It will go out when a time of day
is set or when the timer is set to manual.
The ‘AUTO’ symbol will flash at the end of an Auto Cooking programme to indicate
that the programme has finished.
(When the ‘AUTO’ symbol is flashing, to return the oven to Manual operation,
turn the oven controls off, ensure that the correct time of day is set, and press
the “Manual” button – The ‘AUTO’ symbol will go out).
TIMER FUNCTION BUTTONS
Minute Minder
Button
Here you can set a time period of up to 23 hours 59 minutes, that will count down.
When it reaches zero, the timer will emit an audible tone.
For Example: If you set 20 minutes, the audible tone will occur 20 minutes later.
AUTO COOKING PROGRAMME
Cook Period Button Cook Period is the actual length of time for which, the timer will switch the oven(s) on
as part of an “Auto Cooking” programme.
(e.g. If you set 2 hours, the food will be cooked for 2 hours).
The time of day at which you want an “Auto Cooking” programme to end.
End Time Button
For Example: If you set a “Cook Period” for 2 hours, and “End Time” of 11:00. The timer
will switch the oven(s) on at 9:00 and turn the oven(s) off at 11:00. You will hear a
audible tone at 11:00, to indicate that the Auto Cooking Programme has finished.
Notes:
- When setting an Auto Cooking programme you will need to set the oven
control(s) to the required temperature(s) when you set the timer.
- If an Auto Cooking programme has been set the oven(s) will only operate during
the pre-programmed time.
Manual Button
Needs to be pressed to cancel an Auto Cooking programme and return the oven(s) to
Manual operation.
“+” and “–” Buttons Used to adjust the various timer function settings.
7
TIMER OPERATION
SETTING THE TIME OF DAY
Step 1 Make sure all oven controls are turned Off.
Step 2 Check the electricity supply to the cooker is turned on.
Step 3 When switched on the display will show 0.00 and the Auto symbol,
flashing intermittently.
Step 4 Press & hold in both the Cook Period & End Time buttons together.
Step 5 With the Cook Period & End Time buttons still held in, press either the “+”
or “–” buttons to set the correct time of day.
Step 6 Release all the buttons simultaneously.
THE TIME OF DAY IS NOW SET.
To change the time of day repeat Steps 4, 5 & 6 above.
Note:
You cannot adjust the time of day if the timer has been set for an
Auto Cooking Programme.
SETTING THE MINUTE MINDER
Step 1 Ensure the time of day is set correctly.
Step 2 Press and hold the Minute Minder button.
Step 3 With the Minute Minder button held in, set the required Minute Minder
period using the “+” and “–” buttons. A ‘bell’ symbol will light up.
Release all buttons and the timer display will revert back to the time of day.
The ‘bell’ symbol will remain lit to signify that a Minute Minder period has been
set.
At the end of the set time an audible tone will be heard, and the ‘bell’ symbol will
disappear.
Step 4 To cancel the audible tone press the Minute Minder button.
Note 1
When the Minute Minder has been set, the time remaining can be checked at any
time by simply pressing the Minute Minder button.
Note 2
If necessary the Minute Minder can be cancelled before the tone sounds by
pressing and holding the Minute Minder button and then at the same time
pressing the “–” button until 0.00 appears in the display window.
8
TIMER OPERATION
AUTO COOKING PROGRAMMES
There are two Auto Cooking programmes that can be selected using your timer:–
(a) To set the timer to switch the oven(s) On and Off Automatically
(b) To set timer to switch on immediately and OFF automatically after a set cook period.
a) TO SET THE TIMER TO SWITCH THE OVEN(S) ON AND OFF AUTOMATICALLY
This allows you to cook at a specified time for a chosen period before the oven switches
off Automatically.
Step 1 Check that the correct time of day is set, if not follow instructions for setting the time of day.
Step 2 Place food onto the correct shelf position in the oven and close the oven door(s).
Step 3 Press and hold in the Cook Period button.
The display will read 0.00 with the ‘cookpot’ symbol lit.
Step 4 With the Cook Period button still held in, set the required Cook Period
using the “+” and “–” buttons.
Release the buttons and the timer display will revert to the time of day with the
‘Auto’ symbol and ‘cookpot’ symbol lit.
Step 5 Press and hold in the End Time button.
The display will read the earliest possible end time for the Cook Period
that you have set above.
The ‘Auto’ symbol and ‘cookpot’ symbol will be lit.
Step 6 With the End Time button still held in, use the “+” and “–” buttons to set
the ‘End Time’ (i.e. The time you require the oven to switch off ).
Release all the buttons and the timer will revert back to the time of day.
The ‘Auto’ symbol will remain lit to signify that an Auto Cooking Programme has
been set. The ‘cookpot’ symbol will go out.
Step 7 Turn the oven control(s) to the required temperature, and if necessary
select the appropriate oven function.
At the end of the Automatic Cook Period the Auto Symbol will flash and an
intermittent bleeping sound will be heard.
The audible tone will continue unless cancelled.
The ‘Auto’ symbol will continue to flash until the timer is returned to Manual
operation (see below).
Step 8 Press the Manual button, the audible tone will be cancelled and the
oven(s) will be returned to Manual.
Step 9 Turn the oven control(s) to the OFF position.
9
TIMER OPERATION
Note 1
When cooking automatically the Cook Period can be checked at any time by simply
pressing the Cook Period button.
Note 2
When cooking automatically the End Time can be checked at any time by simply
pressing the End Time button.
b) TO SET TIMER TO SWITCH ON IMMEDIATELY AND OFF AUTOMATICALLY AFTER A SET COOK
PERIOD
Step 1
Step 2
Step 3
Check that the correct time of day is set, if not follow instructions for setting the time of day.
Place food onto the correct shelf position in the oven and close the oven door(s).
Turn the oven control(s) to the required temperature, and if necessary select the appropriate oven
function.
Step 4 Press & hold in the Cook Period button, the display will read 0.00 and the
‘cookpot’ symbol will light up.
With the Cook Period button still held in set the required Cook Period using the
“+” and “–” buttons. Example: 1hr 30 minutes (as shown).
Note: Cook Period is the length of time the food requires to cook.
Step 5 Release all buttons.
The timer display will revert to the time of day with the ‘Auto’ symbol lit &
‘cookpot‘ symbol remaining lit.
NOTE: The Cookpot symbol disappears
At the end of the Cook Period the ‘Auto’ symbol will flash and an intermittent
audible tone will be heard.
The audible tone will continue until cancelled. The ‘Auto’ symbol will continue to
flash until the timer is returned to Manual operation (see below).
Step 6 Press the Manual button. The audible tone will be cancelled and the
oven(s) will be returned to Manual.
Step 7 Turn the oven control(s) to the OFF position.
10
TIMER OPERATION
TO CANCEL AN AUTO COOKING PROGRAMME BEFORE
THE COOK PERIOD HAS FINISHED.
Step 1 Turn the oven control(s) to the OFF position.
Step 2 Press the Manual button to return the oven(s) to “Manual” operation.
The ‘Auto’ symbol will go out.
Note 1
When cooking automatically the Cook Period can be checked at any time by simply pressing
the Cook Period button.
OTHER NOTES ON TIMER OPERATION
1. When cooking Automatically the Cook Period can be checked at any time simply by pressing the Cook
Period button.
2. When cooking Automatically the End Time can be checked at any time by simply pressing the End Time
button.
3. Having set a Cook Period and End Time an electronic device stores the information. The device within the
timer will switch the oven(s) on and off at the required times.
4. When setting an Auto Cooking Programme and a mistake is made, to clear:–
(a) Press & release the Manual button.
(b) Start the sequence again.
5. If at any time the display shows three flashing zero’s 0.00 and ‘Auto’, it is likely that the electricity supply to
the oven has been interrupted. Reset the timer to the correct time of day.
Food in the oven may, therefore, not have been cooked, before serving check food is thoroughly heated
and completely cooked.
6. To set each function always press and hold the required function button and at the same time press “+” or
“–” buttons.
11
HOTPLATE
The hotplate lid is fitted with a safety device which cuts off the gas supply to the
hotplate burners unless the lid is fully open. Do not use the safety device as a means of
controlling the hotplate burners.
The hotplate has two high speed burners and two simmering burners which will
accommodate pans between 100mm (4”) and 230mm (9”) diameter. All pans should be
positioned centrally over the burners.
TO USE THE HOTPLATE
1. Remove any items or spillage from the top of the lid and then raise it to its
fully open position.
2. Press the ignition button and then push in and turn the control knob of the
chosen burner anti-clockwise to the large flame symbol. Continue to press
the ignition button until the sparks light the gas.
3. Turn the control knob anti-clockwise to the desired setting.
Only turn the control knob between the large flame symbol and the small
flame symbol for adjusting the setting.
4. To turn off, turn the control knob fully clockwise to the symbol O.
DO NOT use the hotplate unless all pan supports are in position.
DO NOT use mis-shapen pans which may be unstable.
DO NOT use round base woks directly on the pan supports.
DO NOT use the glass lid as a working surface.
Each burner is fitted with a spark ignitor for lighting the gas. To ensure rapid lighting of
the burners every time they are used, the ignitors must be kept clean and dry. Remove
any food spillage or cleaning materials from the ignitor using a small nylon brush such
as a tooth brush. Access to the ignitor can be achieved by lifting off the loose burner
parts carefully when the burners are cool.
When the hotplate burner bodies and caps are removed for cleaning, be careful not to
drop any food particles or cleaning materials into the burner bases, to avoid the
possibility of blocking the gas jets.
If aluminium based pans are used, a silvery deposit may appear on the top edge of the
pan support fingers. See ‘Care and Cleaning’ section for cleaning information.
12
HOTPLATE
SAFETY REQUIREMENTS FOR DEEP FAT FRYING
1. Never fill chip pans more than one third full with oil or fat.
2. Never leave oil or fat unattended during the heating or cooling period.
3. Never heat fat or fry with a lid on the pan.
4. Always dry food thoroughly before frying, and lower it slowly into the hot oil
or fat. Frozen foods in particular will cause frothing and spitting if added too
quickly.
5. Always keep the outside of the pan clean and free from streaks of oil or fat.
HOW TO DEAL WITH A FAT FIRE
1. Do not move the pan.
2. Turn off the hotplate burners.
3. Smother the flames with a fire blanket or damp cloth to extinguish the fire.
Do not use water or a fire extinguisher as the force of it may spread the
burning fat or oil over the edge of the pan.
4. Leave the pan for at least 60 minutes before moving it.
13
GRILL
CAUTION – ACCESSIBLE PARTS MAY BECOME HOT WHEN THE GRILL IS IN USE.
YOUNG CHILDREN SHOULD BE KEPT AWAY.
GRILLING SHOULD NEVER BE UNDERTAKEN WITH THE GRILL DOOR CLOSED.
The grill control is designed to provide variable heat control of either the full width of
the grill or just the left half. Turning the control knob clockwise will switch on the full
width and turning anti-clockwise will switch on just the left half.
A gentle flow of air will be blown from underneath the control panel when the grill or
top oven is in use.
GRILL PAN HANDLE
The grill pan handle is detachable from the pan to facilitate cleaning. The handle can be
either detachable from or fixed to the pan.
Remove the screw and washer from the grill pan bracket, tilt the handle over the recess
adjacent to the bracket (A). Slide the handle toward the centre of the pan (B) and let the
handle locate over the bracket (C).
For a detachable handle: Remove the screw and washer from the grill pan and keep
safe.
For a fixed handle: Replace the screw and washer and ensure they are fully tightened.
Warning: Ensure when using grill pan handle in the detachable manner it is centralised
and secure.
A
B
C
TO USE THE GRILL
1. Open the grill/top oven door and place the shelf in the required position.
2. Turn the grill control knob clockwise to 4 (or Max) for full width grilling or
anticlockwise for the half grill.
3. Slide the grill pan toward the back of the grill compartment until it stops.
4. Leave the control at 4 (or Max) for toast and for sealing and fast cooking of foods.
For thicker foods requiring longer cooking, turn the control to a lower setting after
sealing on both sides at 4 (or Max).
NOTE: The grill will not operate unless the top oven control is in the OFF position.
Grilling can be started from cold but for best results preheat for approximately 2
minutes.
The grill elements are covered by a wire mesh to prevent access to live parts. Under no
circumstances should pointed objects be inserted through the mesh.
During use, the mesh may become soiled. Do not attempt to clean it while the grill is
on. Turn the cooker off at the control unit and wait until it has cooled down before
cleaning.
DO NOT cover the grill pan or grid with aluminium foil as this can hold fat, intensify
the heat and cause a fire hazard.
14
OVENS
Both ovens have a thermostat light that will illuminate until the oven has reached the
set temperature. It will then switch off and on during cooking as the thermostat
maintains the temperature.
Each shelf has a safety stop to prevent it from being pulled out too far when attending
to food. Shelves are removed by pulling them out to the stop and then lifting at the front
to withdraw. The oven cooking charts are a guide only, giving approximate cooking
temperatures and times. To suit personal taste and requirements it may be necessary to
increase or decrease temperatures by 10˚C.
A gentle flow of air will be blown from underneath the control panel when the top oven
or grill is in use.
TOP OVEN - CONVENTIONAL COOKING
The top oven can be used to cook small quantities of food or used in conjunction with
the main oven to provide additional cooking space.
TO USE THE TOP OVEN
1. Place oven shelf in chosen position (refer to cooking chart).
2. Turn the top oven control knob clockwise to the required setting. The top oven
thermostat light will go off when the oven has reached the set temperature.
Food should be placed in the centre of the shelf with a gap of at least 25mm (1 inch)
between it and the grill element to avoid burning and ensuring an even cooking.
Do not place food or dishes on the floor of the oven.
MAIN OVEN - FAN COOKING
Fan cooking is ideal for large poultry or joints of meat, reducing cooking times and
often eliminating the need for preheating the oven. It is also ideal for batch cooking
where food is cooked on more than one level, because the forced circulation of hot air
gives an even temperature from the top to the bottom of the oven.
When cooking recipes that are not designed for a fan oven, it is recommended that the
temperature is reduced by about 25˚C and the time reduced by about 10 minutes for
each hour. If a large quantity of food is being cooked, it will be necessary to increase
the cooking time to compensate for the extra oven load.
TO USE THE MAIN OVEN
1. Check that the timer is set to manual mode.
2. Place oven shelves in chosen position (refer to cooking chart).
3. Turn the main oven control knob clockwise to the required setting. Pre-heating is
not normally necessary, but some foods such as bread, scones and Yorkshire
pudding do benefit from being placed in a hot oven.
Food should be placed in the centre of each shelf to allow for even air circulation
around the food.
15
190/200
150
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Beef/ Lamb
(slow roasting)
Beef/ Lamb
(foil covered)
Pork
(slow roasting)
Pork
(foil covered)
Veal
(slow roasting)
Veal
(foil covered)
Poultry/Game
(slow roasting)
Poultry/Game
(foil covered)
Casserole
2-21/2 hrs
25-30 mins per 450g
(1lb)
25-30 mins per 450g
(1lb) + 25 mins over
40-45 mins per 450g
(1lb)
40-45 mins per 450g
(1lb) + 40 mins over
40 mins per 450g (1lb)
40 mins per 450g (1lb)
+ 40 mins over
35-40 mins per 450g
(1lb)
35 mins per 450g (1lb)
+ 35 mins over.
Time (approx.)
Top Oven Cooking
Runner 1
from
bottom
of oven.
Casserole
over 5.5kg (12lb)
Turkey 4 to 5.5kg
(8 to 12lb)
Chicken/ Turkey
up to 4kg (8lb)
Veal
Pork
Lamb
Beef
Position
in Oven Meat
No
No
No
No
No
No
No
140-150
160/180
160/170
160/180
160/180
160/180
Pre- Temperature
heat
˚C
Time (approx.)
11/2 - 2 Hrs
allow 12 mins per
450g at 150oC
13-15 mins per 450g
(1lb) at 150/160oC
18-20 mins per 450g
(1lb) + 20 mins extra
25-30 mins per 450g
(1lb) + 25 mins extra
25-30 mins per 450g
(1lb) + 25 mins extra
20-30 mins per 450g
(1lb) + 25 mins extra
20-25 mins per 450g
(1lb) + 20 mins extra
Fan Oven Cooking
If using aluminium foil, never: 1. Allow foil to touch sides of oven. 2. Cover oven interior with foil. 3. Cover shelves with foil.
170/180
190/200
170/180
190/200
170/180
190/200
170/180
Pre- Temperature
heat
˚C
Meat
Meat
OVEN COOKING CHART
The most accurate method of testing the readiness of joints of meat or whole poultry is to insert a meat thermometer into the thickest
part of a joint, or the thickest part of poultry thighs, during the cooking period. The meat thermometer will indicate when the required
internal temp has been reached.
Beef - Rare:
60˚C
Lamb: 80˚C
Poultry:
90˚C
Medium:
70˚C
Pork:
90˚C
Well Done: 75˚C
Veal:
75˚C
16
Yes
Yes
Yes
Yes
Yes
Milk Pudding
Baked Custard
Bread
Meringues
30-45
150-180
100
40-50
90-120
20-30
200/210
150/160
140/150
200/210
30-40
Yes
Yes
No
Runner 2 from
bottom of oven.
Yes
Runner 1
Runner 1
Runner 1
Runner 2 from
bottom of oven.
180/190
Individual Yorkshire
Puddings
190/200
Runner 2 from
bottom of oven.
Yes
Yorkshire Pudding
190/200
Runner 1 from
bottom of oven.
Time Dependent
on recipe
Yes
Puff Pastry
200/210
190/200
Yes
Shortcrust Pastry
Note: If soft margarine is used for cake making, temperatures recommended by the
manufacturers should be followed. Temperatures recommended in this chart refer to
cakes made with block margarine only.
80-90
200/210
140/150
130/140
190/200
190/200
130/140
Runner 1 from
bottom of oven.
140/150
Yes
Rich Fruit Cakes
140/150
180/200
170/190
Time Dependent
on recipe
150/160
Yes
Semi-rich Fruit
cakes
Yes
Yes
Runner 1
10-15
200/210
Yes
Swiss Roll
Runner 1 from
bottom of oven.
Runner 1 from
bottom of oven.
160/170
170/180
210/220
180-240
45-50
40-50
105-135
20-25
40-45
Dependent
on use
45-50
Depending
on size
75-90
12-15
15-20
20-25
15-20
8-10
Temperature Time in mins.
˚C
Time Dependent
on size
20-25
180/190
Yes
Sponge Sandwich
(fatless)
Runner 1
Yes
Preheat
Runner 1
20-30
170/180
Yes
Victoria Sandwich
Runner 1 from
bottom of oven.
Runner 1 from
bottom of oven.
Position in
Oven
Fan Oven Cooking
60-75 7 inch
20-25
180/190
Yes
Small Cakes
10-15
Yes
Scones
Temperature Time in mins.
˚C
Top Oven Cooking
210/220
Preheat
Food
Baking
OVEN COOKING CHART
17
THE ‘SLOW COOK’ SETTING
The 90˚ setting on the main oven thermostat can be used for slow cooking.
PREPARING FOOD FOR SLOW COOKING
1. All dishes cooked by the ‘Slow Cook’ setting should be cooked for a minimum 6
hours.They will ‘hold’ at this setting for a further hour but marked deterioration in
appearance will be noticed in some cases.
2. Joints of meat and poultry should be cooked at 170˚ for 30 minutes before turning to
the ‘Slow Cook’ setting and never be cooked lower than the middle shelf position.
3. Joints of meat over 6 lbs (2.7kg) and poultry over 4 lbs 8oz (2 kg) should not be
cooked using the ‘Slow Cook’ setting.
4. Always stand covered joints on a rack over the meat tin to allow good air circulation.
5. A meat thermometer should be used when cooking pork joints and poultry.
The internal temperature of the food should reach at least 88˚C.
6. This method is unsuitable for stuffed meat and stuffed poultry.
7. Always bring soups, casseroles and liquids to the boil before putting in the oven.
8. Cover casseroles with foil and then the lid to prevent loss of moisture.
9. Always thaw frozen food completely before cooking.
10. Root vegetables will cook better if cut into small pieces.
11. Adjust seasonings and thickenings at the end of the cooking time.
12. Use the zones of heat in the oven, e.g. meringues and milk puddings can be cooked
lower in the oven whilst other dishes requiring greater heat can be cooked above
them.
13. Egg and fish dishes need only 1-5 hours cooking and should be included in day
cooking sessions, when they can be observed from time to time.
14. Dried red kidney beans must be boiled for a minimum of ten minutes after soaking,
before inclusion in any dish.
18
CARE AND CLEANING
Switch off the electricity supply and allow to cool before cleaning the cooker.
Clean the cooker regularly and wipe up spills soon after they occur to prevent
them from becoming burnt on. Never use biological washing powder, caustic
cleaners, harsh abrasives, scouring pads, steam cleaners, aerosol cleaners or oven
chemical cleaners of any kind.
Before moving your cooker ensure that it is cool and note that it is heavy
(approximately 70 kg 155 lbs), so you may require assistance. To move the cooker
forward, open the top oven/grill door and with both hands positioned under the roof
of the compartment, lift and pull forward. Replace by pushing the cooker backwards.
Check that the cooker is level. Take care to ensure that any floor covering is not
damaged.
OVEN HEAT CLEAN LININGS
The oven side linings are coated with a special enamel which has a continuous
cleaning action. The higher the oven temperature the more effective the action. In
most cases this cleaning operation will proceed during normal cooking. However, if
roasting is done frequently, or high temperatures are not used regularly, it may be
necessary to run the oven empty at maximum setting for about two hours.
It should not normally be necessary to clean the linings with water, but if desired, wipe
them over with a soapy cloth, followed by a wipe with a damp clean cloth.
REPLACEMENT OF OVEN LIGHT BULB
CAUTION: DISCONNECT THE APPLIANCE FROM THE ELECTRICITY SUPPLY BEFORE
REPLACING THE LAMP TO AVOID THE POSSIBILITY OF AN ELECTRIC SHOCK
Light bulbs are not covered by the manufacturer’s guarantee.
A new 15W, 300˚C rated SES bulb can be obtained from your cooker supplier or any
major electrical retailer.
1. Remove the shelves from the oven.
2. Unscrew the lens using a thick cloth to protect your fingers in the unlikely event of
a lens fracture.
3. Unscrew bulb.
4. Fit new bulb and refit lens.
19
CARE AND CLEANING
COOKER FINISH
CLEANING METHOD
Vitreous Enamel
Hotplate (Henley), pan
supports, burner caps,
roasting dish, grill pan, main
oven base, inside of grill
compartment.
Cloth wrung out in warm soapy water. Stubborn
stains can be removed with a cream paste,
liquid cleaner or by rubbing with fine steel wool
soap pads.
Check that the cleaning agent is approved by the
Vitreous Enamel Association.
Paint
Plinth, control panel (trim),
side panels, doors (trim).
Wash with a cloth wrung out in warm soapy water
only.
DO NOT USE ABRASIVES.
Aluminium
Hotplate side trims, hotplate
burner bodies, lid rear trim,
rear flue grille.
Similar to paint cleaning above. Use a nylon brush
to remove any cleaning materials, water or dirt from
the hotplate burner bodies.
Glass
As for enamel cleaning. Polish with a clean dry cloth
or kitchen roll.
Chromium Plating
Oven shelves, grill pan grid,
grill pan handle support
Wipe with a cloth wrung out in warm soapy water.
A fine steel wool soap pad e.g. Brillo, Ajax, or a
chrome or stainless steel cleaner may be used.
Plastic
Grill pan handle, control
knobs
Wipe with a cloth wrung out in warm soapy water.
Wipe with a cloth wrung out in warm soapy water.
Stainless Steel (Professional)
Polish with a clean dry cloth or kitchen towel. For
Door trims, control panel,
stubborn stains use a proprietary stainless steel
hotplate
cleaner and follow the instructions on the container.
20
SOMETHING WRONG
WITH YOUR COOKER
Before contacting your Service Centre or Installer, check the problem guide
below, there may be nothing wrong with your cooker.
PROBLEM
CHECK
Ignition does not work.
If all burners fail to ignite:
Check that sparks appear at the burners; a clicking
noise should be heard.
If not...
Hotplate burner.
Check that the electricity supply is turned on.
If the electricity supply has failed, the hotplate
burners can be lit by a match.
If only one burner fails to ignite:
Burner ports
Ignitor
Check that the burner is dry and that spillage of food
or cleaning fluid remains are not affecting the ignitor
or burner ports.
Clean away any debris with a dry nylon brush such as
an old toothbrush. If a wire wool pad has been used
for cleaning around the burner ensure the ignitor is
free from any stray strands. Any water on the burner
should be dried with a cloth or kitchen towel.
Make sure that all the burner parts are correctly
seated.
21
SOMETHING WRONG
WITH YOUR COOKER
PROBLEM
Slight odour or small
amount of smoke when
grill / oven used first
time
CHECK
This is normal and should cease after a short period.
Oven cooks too fast or too
slow
Check that the temperature and shelf positions are as
recommended in the Oven Cooking Charts. However, it
may be necessary to increase or decrease the
recommended setting slightly to suit your taste.
Cannot set an “Auto Cook”
programme or
cannot get the timer to turn
the oven on or off at the
required times.
Read the Timer instructions in this book carefully
remembering that the Cook period is the length of time
that the timer will switch the oven(s) on as part of an Auto
Cooking Programme.
Timer Display shows "0:00"
with "Auto" Flashing.
The electricity supply to the cooker may have been been
interrupted, but has now come back on again. set the
correct time of day by following the instructions given in
the timer section of this book.
Main Oven does not work, but
the grill, Top Oven and
hotplate burners work.
The timer may be set for an Auto Cooking Programme.
Check the timer to see if “AUTO” is illuminated. If it is,
follow the instructions given in the timer section of this
book to cancel the Auto Cooking Programme.
Oven lamp does not work
The oven lamp is not covered by the guarantee. The part
is easily changed (see the section on oven lamp
replacement). A new lamp may be obtained from our
Parts department see Key Contacts (back page).
DISPOSAL OF YOUR PRODUCT:
To minimise the risk to injury to children please dispose of your product carefully and safely.
Remove all doors and lids (where fitted). Remove the mains cable (where fitted) by cutting off
flush with the appliance and always ensure that no plug is left in a condition where it could be
connected to the electricity supply.
To help the environment, Local Authority instructions should be followed for the disposal of
your product.
22
INSTALLATION INSTRUCTIONS
Prior to installation, ensure that the local distribution conditions (nature of the gas
and gas pressure) and the adjustment conditions are compatible. The adjustment
conditions for this appliance are stated on the rating label which is fitted on the
back panel.
This appliance is not designed to be connected to a combustion products
evacuation device. It must be installed and connected in accordance with current
installation regulations. particular attention should be given to the relevant
requirements regarding ventilation.
MODEL NUMBER 10430G, 10682G, 10685G, 10688G, 10475G, 10476G
Category Il2H3+ (GB. IE)
These models are set to burn NATURAL GAS (G20) at 20mbar but can be
converted for use on BUTANE (G30) at 28-30mbar or PROPANE (G31) at
37mbar with the use of the conversion kit (refer to page 27).
GAS SAFETY (INSTALLATION & USE) REGULATIONS
It is the law that all gas appliances are installed by competent persons in
accordance with the current edition of the above regulations. It is in your interest
and that of safety to ensure compliance with the law.
In the UK, CORGI registered installers work to safe standards of practice.
The cooker must also be installed in accordance with BS 6172.
Failure to install the cooker correctly could invalidate the warranty liability claims
and could lead to prosecution.
LOCATION
The cooker may be located in a kitchen, kitchen/diner or a bed-sitting room, but
not in a room containing a bath or shower. The cooker must not be installed in a
bed-sitting room of less than 20m3.
When adjusted for use on BUTANE (G30) or PROPANE (G31) the cooker must
not be installed in a room or internal space below ground level, e.g. in a
basement.
PROVISION FOR VENTILATION
The room containing the cooker should have an air supply in accordance with
BS 5440: Part 2.
The room must have an opening window or equivalent; some rooms may also
require a permanent vent. If the room has a volume between 5 and 10m3, it will
require an air vent of 50cm2 effective area unless it has a door which opens
directly to outside. If the room has a volume of less than 5m3, it will require an air
vent of 100cm2 effective area. If there are other fuel burning appliances in the
same room, BS 5440: Part 2 should be consulted to determine air vent
requirements.
23
INSTALLATION INSTRUCTIONS
TECHNICAL DATA
DIMENSIONS
Height
Width
Depth
900 - 915mm
600mm
595mm (excluding door handles)
GENERAL
Gas connection
Pressure test point
Gas rate adjustment
Aeration adjustment
Electrical connection
Rp 1/2 (1/2” BSP female)
Hotplate burner injector.
None
None
4mm2 twin and earth.
230-240V a.c. 50Hz.
Natural Gas
24
LPG
Heat Input
Injector
Heat Input
Injector
HOTPLATE
Front left and rear right
3.0kW
128
2.8kW
(205g/h)
82
HOTPLATE
Front right and rear left
1.9kW
102
1.8kW
(130g/h)
65
GRILL
2.4 / 2.6kW
TOP OVEN
1.7 / 1.85kW
MAIN OVEN
2.3 / 2.5kW
INSTALLATION INSTRUCTIONS
SPACE FOR FIXING
The cooker can be close fitted below hotplate level. This requires a
minimum distance of 600mm between cupboard units of hotplate height.
When installing next to a tall cupboard, partition or wall, for a minimum
distance of 400mm above hotplate level, allow a side clearance of at least
65mm.
The diagram below illustrates the minimum clearance between the cooker
and adjacent walls, cupboards etc.
840 mm Min
750
400 mm Min
The wall behind the cooker between the hotplate and 450mm above, and
the width of the cooker, must be a non-combustible material such as
ceramic wall tiles.
65 mm Min
If the cooker is to
be fitted close to a
corner base unit on
the left hand side,
ensure that there is
a clearance of at
least 50mm to
allow the oven
door to open fully
for when removing
oven shelves.
600 mm Min
COOKER HOODS
If a cooker hood is to be installed, refer to the cooker hood manufacturers’
instructions regarding fixing height.
UNPACKING THE COOKER
Unpack the components from inside the grill and oven: Check that the
following parts are present:
Grill pan and grid
Meat pan
Pan supports
Oven shelves (3)
Enamelled burner caps (4)
Literature
Aluminium burner bodies (4)
Anti Splash tray
LPG conversion kit
25
INSTALLATION INSTRUCTIONS
LEVELLING
1.
2.
Two rear wheels and two front feet are fitted which can be adjusted up or down to set
the height (915mm) and level the cooker.
The rear wheels can be raised or lowered from the BACK of the cooker by adjusting the
levelling screws ‘A’ in the plinth.
The front feet can be simply screwed in or out to lower or raise the front of the cooker.
CAUTION: Some soft floor coverings may get damaged if the cooker is not moved
carefully.
NOTE: Ensure oven shelves are level by using a spirit level on the rod shelves
VIEWED FROM REAR
STABILITY BRACKET
The back of the cooker has a slot for engagement of a stability bracket, which can
be obtained, as an extra, from your cooker supplier.
CONNECTING TO GAS SUPPLY
The cooker is designed to match the depth of standard 600mm worktops. An
adaptor backplate should, therefore, be fitted within the shaded area shown to
allow the cooker to be pushed fully to the wall.
220mm
GAS
BACKPLATE
POSITION
REAR OF
COOKER
70mm
125mm
STABILITY
BRACKET
POSITION
450 mm
635mm
SLOT FOR
STABILITY
BRACKET
26
Connection to the cooker should be made with an approved appliance flexible
connection to BS 669. Hoses connected to LPG should be suitable for LPG and
capable of withstanding 50mbar pressure A length of 0.9 to 1.25m is
recommended. The length of hose chosen should be such that when the cooker is
in situ, the hose does not touch the floor.
The temperature rise of areas at the rear of the cooker that are likely to come in
contact with the flexible hose do not exceed 70˚C.
INSTALLATION INSTRUCTIONS
ELECTRICAL INSTALLATION
WARNING - THIS APPLIANCE MUST BE EARTHED
The cooker must be connected by a qualified electrician to a suitable double - pole control
unit with a minimum rating of 32A and a minimum contact clearance of 3mm, which
should be fitted adjacent to (but not above) the cooker, in accordance with IEE
regulations.
The power supply cable should conform to BS6004 with a conductor size of 4mm2.
The control unit should be easily accessible in the event of an emergency.
This appliance conforms to EN55014 regarding suppression of radio and television
interference.
Access to the mains terminals is gained by removing the rear access cover.
The mains cable must pass through the cable clamp adjacent to the terminal block, and
the screws must be fully tightened. Sufficient cable should be used to allow the cooker to
be pulled out for servicing.
Take care not to trap the mains cable when pushing the cooker into its final position.
CONVERSION FOR USE WITH LPG
Referring to the chart on page 24, remove the natural gas injectors and replace with
those for LPG from the conversion kit provided. Remove the hotplate control knobs and
using a long narrow flat bladed screwdriver, turn the bypass screw located down the
centre of each control spindle, fully clockwise.
Secure the label supplied with the kit, over the relevant part of the data badge to show the
new adjustment conditions.
OPERATIONAL CHECKS
After installation, check for gas soundness. The supply pressure can be checked at one of
the hotplate burner injectors.
Check that the hotplate burners ignite correctly and burn with a steady flame. Check for a
steady flame at the low setting.
Instruct the user on the operation of the cooker.
27
Key Contacts
After Sales Service
Over 1100 trained specialists, directly employed by us, to ensure that you can have
complete confidence in both the appliances and services we offer.
Repair Service and Information Help Desk
UK: 08709 066 066
Monday to Friday, 8am to 7.30pm
Saturday, 8.30am to 5.30pm
Sunday, 9.30am to 3.30pm
www.cannonservice.co.uk
Republic of Ireland: 1850 302 200
Note: Our operators will require the following information:
Model number
Serial number
Extended Warranties
UK 08709 088 088
Monday to Sunday, 8am to 8pm
www.cannonservice.co.uk
Republic of Ireland: 1850 502 200
Genuine Parts & Accessories
UK: 08709 077 077
Monday to Friday, 8.30am to 5pm
Saturday, 8.30am to 12noon
www.cannonservice.co.uk
Republic of Ireland: (01) 842 6836
www.cannon.co.uk
Indesit Company UK Limited, Morley Way, Peterborough, PE2 9JB
PRINTED BY: SIMLEX . FOUR ASHES, WOLVERHAMPTON.