www.weslo.com
Model No. WLEX31310.0
Serial No.
Write the serial number in the
space above for reference.
Serial Number
Decal
QUESTIONS?
If you have questions, or if parts are
damaged or missing, DO NOT
CONTACT THE STORE; please
contact Customer Care.
IMPORTANT: Please register this
product (see the limited warranty
on the back cover of this manual)
before contacting Customer Care.
1-866-699-3756
CALL TOLL-FREE:
Mon.–Fri., 6 a.m.–6 p.m. MT
Sat. 8 a.m.–4 p.m. MT
ON THE WEB:
www.wesloservice.com
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Keep this manual
for future reference.
USER'S MANUAL
TABLE OF CONTENTS
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
HOW TO USE THE EXERCISE BIKE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
FCC INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
WARNING DECAL PLACEMENT
This drawing shows the location(s) of the
warning decal(s). If a decal is missing or
illegible, call the telephone number on the
front cover of this manual and request a
free replacement decal. Apply the decal in
the location shown. Note: The decal(s) may
not be shown at actual size.
WESLO is a registered trademark of ICON IP, Inc.
2
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read all important precautions and
instructions in this manual and all warnings on your exercise bike before using your exercise bike.
ICON assumes no responsibility for personal injury or property damage sustained by or through the
use of this product.
8. Wear appropriate clothes while exercising;
do not wear loose clothes that could become
caught on the exercise bike. Always wear
athletic shoes for foot protection.
1. Before beginning any exercise program,
consult your physician. This is especially
important for persons over age 35 or persons with pre-existing health problems.
9. The exercise bike should not be used by
persons weighing more than 250 lbs.
(113 kg).
2. Use the exercise bike only as described in
this manual.
3. It is the responsibility of the owner to ensure
that all users of the exercise bike are adequately informed of all precautions.
10. The pulse sensor is not a medical device.
Various factors, including the user's movement, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
4. The exercise bike is intended for home use
only. Do not use the exercise bike in a commercial, rental, or institutional setting.
11. The exercise bike does not have a free
wheel; the pedals will continue to move until
the flywheel stops. Reduce your pedaling
speed in a controlled way.
5. Keep the exercise bike indoors, away from
moisture and dust. Place the exercise bike
on a level surface, with a mat beneath it to
protect the floor or carpet. Make sure that
there is at least 2 ft. (0.6 m) of clearance
around the exercise bike.
12. Always keep your back straight while using
the exercise bike; do not arch your back.
6. Inspect and properly tighten all parts regularly. Replace any worn parts immediately.
13. Over exercising may result in serious injury
or death. If you feel faint or if you experience
pain while exercising, stop immediately and
cool down.
7. Keep children under age 12 and pets away
from the exercise bike at all times.
3
BEFORE YOU BEGIN
Thank you for selecting the new WESLO® PURSUIT
CT 1.5 exercise bike. Cycling is an effective exercise
for increasing cardiovascular fitness, building
endurance, and toning the body. The PURSUIT CT 1.5
exercise bike provides a selection of features
designed to make your workouts at home more effective and enjoyable.
after reading this manual, please see the front cover
of this manual. To help us assist you, note the product
model number and serial number before contacting
us. The model number and the location of the serial
number decal are shown on the front cover of this
manual.
Before reading further, please review the drawing
below and familiarize yourself with the labeled parts.
For your benefit, read this manual carefully before
you use the exercise bike. If you have questions
Handlebar
Console
Pulse Sensor
Resistance Knob
Seat
Water Bottle Holder
Seat Post Knob
Leveling Cap
Pedal/Strap
*Water bottle is not included
4
ASSEMBLY
To hire an authorized service technician to assemble the exercise bike, call 1-800-445-2480.
Assembly requires two persons. Place all parts of the exercise bike in a cleared area and remove the packing
materials. Do not dispose of the packing materials until assembly is completed.
In addition to the included tool(s), assembly requires a Phillips screwdriver
wrench
, and pliers
.
, an adjustable
See the drawings below to identify the small parts needed for assembly. The number in parentheses below each
drawing is the key number of the part, from the PART LIST near the end of this manual. The number following
the key number is the quantity needed for assembly. Note: If a part is not in the hardware kit, check to see if
it has been preassembled. To avoid damaging parts, do not use power tools for assembly.
M8 Locknut
(10)–6
M4 x 15mm
Screw (48)–6
M8 Split
Washer (50)–3
M8 x 60mm Patch Screw (30)–4
M8 x 15mm Patch
Screw (34)–3
M8 x 65mm Bolt (49)–2
M10 x 70mm Patch Screw (33)–2
5
1.
1
To make assembly easier, read the
information on page 5 before you begin.
Insert the Rear Stabilizer (6) into the Frame (1).
Attach the Rear Stabilizer with four M8 x 60mm
Patch Screws (30).
1
30
2. See the inset drawing. Remove the screw and
the cardboard tube from the Frame (1). Discard
the screw and the cardboard tube.
2
Orient the Front Stabilizer (2) so that the large
holes face the Frame (1).
Attach the Front Stabilizer (2) to the Frame (1)
with two M10 x 70mm Patch Screws (33).
2
33
Large
Holes
Cardboard
Tube
Screw
1
6
1
6
3. While a second person holds the Upright (13)
near the Frame (1), connect the Extension Wire
(23) to the Reed Switch Wire (39).
3
Next, connect the Resistance Cable (19) to the
Lower Resistance Cable (29) in the following
way:
• See drawing A. Pull upward on the metal
bracket on the Lower Resistance Cable (29),
and insert the tip of the Resistance Cable (19)
into the wire clip inside the metal bracket.
13
• See drawing B. Firmly pull the Resistance
Cable (19) upward and slide it into the top of
the metal bracket.
Avoid pinching the
wires and cables
23
19
• See drawing C. Using pliers, squeeze the
prongs on the upper end of the metal bracket
together.
34
Insert the wires and cables downward into the
Frame (1).
50
39
29
1
Tip: Avoid pinching the wires and cables.
Insert the Upright (13) into the Frame (1).
Attach the Upright (13) with three M8 x 15mm
Patch Screws (34) and three M8 Split Washers
(50).
B
A
19
7
50
34
Metal
Bracket
29
C
19
29
Metal
Bracket
4. Attach the Handlebar (42) to the Upright (13)
with two M8 x 65mm Bolts (49) and two M8
Locknuts (10).
4
Attach the Water Bottle Holder (3) to the Upright
(13) with two M4 x 15mm Screws (48).
10
13
42
49
3
48
5. The Console (16) requires four AA batteries (not
included); alkaline batteries are recommended.
IMPORTANT: If the Console has been
exposed to cold temperatures, allow it to
warm to room temperature before inserting
batteries. Otherwise, you may damage the
console displays or other electronic components. Remove the screw, remove the battery
cover, and insert the batteries into the battery
compartment. Make sure to orient the batteries as shown by the diagram inside the
battery compartment. Then, reattach the battery cover.
5
Screw
16
8
Battery
Cover
Batteries
6. While a second person holds the Console (16)
near the Upright (13), connect the wire on the
Console to the Extension Wire (23).
6
16
Insert the excess wire downward into the
Upright (13).
Tip: Avoid pinching the wires. Attach the
Console (16) to the Upright (13) with four M4 x
15mm Screws (48).
13
23
Avoid pinching
the wires
48
7. Attach the Seat (12) to the Seat Post (5) with
four M8 Locknuts (10). Note: The Locknuts
may be preattached to the underside of the
Seat.
7
12
5
10
9
8. Loosen and remove the Seat Post Knob (9)
from the Frame (1).
8
Insert the Seat Post (5) into the Frame (1).
Adjust the Seat Post to the desired height, and
insert the Seat Post Knob (9) through the indicated hole in the Frame into one of the
adjustment holes in the Seat Post.
Tighten the Seat Post Knob (9). Make sure that
the Seat Post Knob is firmly engaged in one
of the adjustment holes in the Seat Post (5).
1
Adjustment
Holes
5
Hole
9
9. Identify the Left Pedal (24), which is marked
with an “L.”
9
Using an adjustable wrench, firmly tighten the
Left Pedal (24) counterclockwise into the left
arm of the Crank (21).
Strap
Tighten the Right Pedal (not shown) clockwise
into the right arm of the Crank (not shown).
21
24
Tab
Adjust the strap on the Left Pedal (24) to the
desired position, and press the end of the strap
onto the tab on the side of the Left Pedal.
Adjust the strap on the Right Pedal (not
shown) in the same way.
10. Make sure that all parts are properly tightened before you use the exercise bike. Note: After assembly
is completed, some extra parts may be left over. Place a mat beneath the exercise bike to protect the floor.
10
HOW TO USE THE EXERCISE BIKE
HOW TO ADJUST THE PEDALING RESISTANCE
HOW TO ADJUST THE SEAT POST
To increase the
resistance of the
pedals, turn the
resistance knob
clockwise; to
decrease the resistance, turn the knob
counterclockwise.
IMPORTANT: Stop
turning the knob
when turning
becomes difficult,
or damage may
result.
For effective exercise, the seat should be at the
proper height. As you pedal, there should be a slight
bend in your knees when the pedals are in the lowest
position.
To adjust the height
of the seat, first
loosen and remove
the seat post knob.
Next, slide the seat
post upward or
Seat
downward and align
one of the adjustment holes in the
Seat Post
seat post with the
indicated hole in the
frame. Insert the
Hole
seat post knob into
Seat Post
the frame and the
Knob
seat post, and then
tighten the seat
post knob. Make
sure that the seat
post knob is
inserted through one of the adjustment holes in
the seat post.
Resistance
Knob
HOW TO LEVEL THE EXERCISE BIKE
If the exercise bike
rocks on your floor
during use, turn one
or both of the leveling caps until the
rocking motion is
eliminated.
Leveling
Caps
11
FEATURES OF THE CONSOLE
HOW TO USE THE MANUAL MODE
1. Turn on the console.
To turn on the console, press any of the buttons or
begin pedaling. The entire display and the pace
guide will turn on for a moment; the console will
then be ready for use.
2. Select the manual mode.
When you turn on
the console, the
manual mode will
be selected. If
you have
selected a pace
workout, reselect
the manual mode
by pressing the Workout Select button repeatedly
until zeros appear in the display.
3. Follow your progress with the display.
The display can show the following workout information:
RPM—The RPM meter on the left side of the display indicates your approximate pedaling pace in
revolutions per minute (rpm).
The console offers a selection of features designed to
make your workouts more effective. While you pedal,
the console will provide continuous exercise feedback.
You can even measure your heart rate using the builtin thumb pulse sensor.
Speed—This mode shows your pedaling speed, in
miles per hour (mph) or kilometers per hour
(km/h).
The console also offers two pace workouts that
prompt you to vary your pedaling pace while guiding
you through effective workouts.
Time—This mode shows the elapsed time. Note:
When a pace workout is selected, the display will
show the time remaining in the workout instead of
the elapsed time.
To use the manual mode, see the instructions at the
right. To use a pace workout, see page 14.
Distance—This mode shows the distance you
have pedaled, in miles or kilometers.
Before using the console, make sure that batteries are
installed (see assembly step 5 on page 8). If there is a
sheet of plastic on the display, remove the plastic.
Calories—This mode shows the approximate
number of calories you have burned.
Pulse—This mode shows your heart rate when
you use the thumb pulse sensor.
Scan—This mode shows the speed, time, distance, calories, and pulse modes, for a few
seconds each, in a repeating cycle. Note: The
pulse mode will appear only while you are using
the pulse sensor.
12
When you turn
Indicators
on the console,
the scan mode
will be selected
automatically.
One indicator will
appear below the
word Scan to
show that the
scan mode is
selected, and a second indicator will show which
information is currently displayed.
Note: When the batteries are replaced, it may be
necessary to reselect the desired unit of measurement.
To reset the display, press the On/Reset button.
To pause the console, stop pedaling. The time will
flash if it is displayed. To continue your workout,
simply resume pedaling.
4. Measure your heart rate if desired.
To measure your
heart rate, stop
pedaling and
place your thumb
on the pulse sensor. Do not
press too hard,
or the circulation in your thumb will be restricted and your
pulse will not be detected. After a few seconds,
the heart-shaped indicator in the display will begin
to flash, two dashes will appear, and then your
heart rate will be shown. Hold your thumb on the
pulse sensor for about 15 seconds for the most
accurate reading.
Note: If you have selected a different mode, press
the Display button repeatedly to reselect the Scan
mode.
To select the
speed, time, distance, or calories
mode for continuous display,
press the Display
button repeatedly. The
indicators will show which mode is selected. Make
sure that there is not an indicator below the word
Scan.
If the displayed heart rate appears to be too high
or too low, or if your heart rate is not displayed, lift
your thumb off the pulse sensor for a few seconds.
Then, place your thumb on the pulse sensor as
described above.
The console can show speed and distance in
either miles or kilometers. The letters “mph” or
“km/h” will appear in the display to show which
unit of measurement is selected.
To change the
unit of measurement, first press
and hold down
the On/Reset
button for a few
seconds. An “E”
for English miles
or an “M” for metric kilometers will appear in the
display. Press the Display button repeatedly to
change the unit of measurement. Then, press the
On/Reset button to save your selection.
Make sure that you are applying the proper
amount of pressure to the pulse sensor. Try the
pulse sensor several times until you become familiar with it. Remember to stand still while
measuring your heart rate.
5. When you are finished exercising, the console
will turn off automatically.
If the pedals do not move for a few seconds, the
console will pause.
If the pedals do not move for a few minutes, the
console will turn off and the display will be reset.
13
HOW TO USE A PACE WORKOUT
During the workout, the pace
guide will prompt
you to keep your
pedaling speed
near the target
pace for the current segment. When the left indicator lights, increase your speed; when the right
indicator lights, decrease your speed. When the
center indicator lights, maintain your current
speed. IMPORTANT: The pace guide is intended
only to provide a goal. Make sure to pedal at a
speed that is comfortable for you.
1. Turn on the console.
See step 1 on page 12.
2. Select a pace workout.
To select a pace
workout, press
the Workout
Select button
repeatedly until
the name of the
desired workout
appears in the
display.
The display can show the time remaining in the
workout. If you stop pedaling for a few seconds,
the workout will pause and the time will flash if it is
displayed. To restart the workout, simply resume
pedaling.
A few seconds after you select a workout, the display will show the duration of the workout.
4. Follow your progress with the display.
Note: The diagrams printed on the console show
the target pace settings for the workouts.
See step 3 on pages 12 and 13.
3. Begin pedaling to start the workout.
5. Measure your heart rate if desired.
Each pace workout consists of one-minute segments. One target pace is programmed for each
segment. Any time the target pace is about to
change, the display will flash for a few seconds to
alert you.
See step 4 on page 13.
6. When you are finished exercising, the console
will turn off automatically.
See step 5 on page 13.
14
MAINTENANCE AND TROUBLESHOOTING
Turn the resistance knob to the lowest setting. Then,
locate the Reed Switch (39). Turn the Crank (21) until
a Magnet (38) is aligned with the Reed Switch.
Loosen, but do not remove, the M5 x 15mm Screw
(47).
Inspect and tighten all parts of the exercise bike regularly. Replace any worn parts immediately.
To clean the exercise bike, use a damp cloth and a
small amount of mild detergent. IMPORTANT: To
avoid damage to the console, keep liquids away
from the console and keep the console out of
direct sunlight.
CONSOLE TROUBLESHOOTING
If the console display becomes dim, replace all the
batteries at the same time; most console problems are
the result of low batteries. To replace the batteries,
see assembly step 5 on page 8.
If the thumb pulse sensor does not function properly,
see step 4 on page 13.
39
47
HOW TO ADJUST THE REED SWITCH
If the console does not display correct feedback, the
reed switch should be adjusted. To adjust the reed
switch, the left pedal and the left shield must be
removed.
38
21
Slide the Reed Switch (39) slightly closer to or away
from the Magnet (38), and then retighten the M5 x
15mm Screw (47). Turn the Crank (21) for a moment.
Repeat these actions until the console displays correct
feedback.
Using an adjustable wrench, turn the left pedal clockwise and remove it. Next, remove all of the screws
from both shields; there are two sizes of screws in
the shields—note which size of screw you remove
from each hole. Then, carefully remove the left
shield.
When the reed switch is correctly adjusted, reattach
the shields and the left pedal.
15
HOW TO ADJUST THE DRIVE BELT
If you can feel the pedals slip while you are pedaling,
even when the resistance is at the highest level, the
drive belt may need to be adjusted. To adjust the drive
belt, the pedals and the shields must be removed.
43
35
Use an adjustable wrench to remove the pedals. To
remove the left pedal, turn the left pedal clockwise; to
remove the right pedal, turn the right pedal counterclockwise.
Next, remove all of the screws from both shields;
there are two sizes of screws in the shields—note
which size of screw you remove from each hole.
Then, carefully remove the shields.
27
Loosen the 3/8" Nut (27) and the Flywheel Nut (43),
which are located on each side of the Flywheel (37).
Then, tighten the M6 Locknuts (32), one on each side
of the Flywheel, until the Drive Belt (35) is properly
tightened.
37
32
Finally, tighten the 3/8" Nut (27) and the Flywheel Nut
(43) and reattach the shields and the pedals.
FCC INFORMATION
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
WARNING: Per FCC rules, changes or modifications not expressly approved by ICON could void the
user's authority to operate the equipment.
16
EXERCISE GUIDELINES
WARNING: Before beginning this
Burning Fat—To burn fat effectively, you must exercise at a low intensity level for a sustained period of
time. During the first few minutes of exercise, your
body uses carbohydrate calories for energy. Only after
the first few minutes of exercise does your body begin
to use stored fat calories for energy. If your goal is to
burn fat, adjust the intensity of your exercise until your
heart rate is near the lowest number in your training
zone. For maximum fat burning, exercise with your
heart rate near the middle number in your training
zone.
or any exercise program, consult your physician. This is especially important for persons
over the age of 35 or persons with pre-existing health problems.
The pulse sensor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The pulse sensor is
intended only as an exercise aid in determining heart rate trends in general.
Aerobic Exercise—If your goal is to strengthen your
cardiovascular system, you must perform aerobic
exercise, which is activity that requires large amounts
of oxygen for prolonged periods of time. For aerobic
exercise, adjust the intensity of your exercise until
your heart rate is near the highest number in your
training zone.
These guidelines will help you to plan your exercise
program. For detailed exercise information, obtain a
reputable book or consult your physician. Remember,
proper nutrition and adequate rest are essential for
successful results.
WORKOUT GUIDELINES
EXERCISE INTENSITY
Warming Up—Start with 5 to 10 minutes of stretching
and light exercise. A warm-up increases your body
temperature, heart rate, and circulation in preparation
for exercise.
Whether your goal is to burn fat or to strengthen your
cardiovascular system, exercising at the proper intensity is the key to achieving results. You can use your
heart rate as a guide to find the proper intensity level.
The chart below shows recommended heart rates for
fat burning and aerobic exercise.
Training Zone Exercise—Exercise for 20 to 30 minutes with your heart rate in your training zone. (During
the first few weeks of your exercise program, do not
keep your heart rate in your training zone for longer
than 20 minutes.) Breathe regularly and deeply as you
exercise–never hold your breath.
Cooling Down—Finish with 5 to 10 minutes of
stretching. Stretching increases the flexibility of your
muscles and helps to prevent post-exercise problems.
EXERCISE FREQUENCY
To find the proper intensity level, find your age at the
bottom of the chart (ages are rounded off to the nearest ten years). The three numbers listed above your
age define your “training zone.” The lowest number is
the heart rate for fat burning, the middle number is the
heart rate for maximum fat burning, and the highest
number is the heart rate for aerobic exercise.
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest
between workouts. After a few months of regular exercise, you may complete up to five workouts each
week, if desired. Remember, the key to success is to
make exercise a regular and enjoyable part of your
everyday life.
17
PART LIST—Model No. WLEX31310.0
Key No. Qty.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
1
1
1
2
1
1
2
2
1
7
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Description
Key No. Qty.
Frame
Front Stabilizer
Water Bottle Holder
Front Stabilizer Cap
Seat Post
Rear Stabilizer
Handlebar Cap
Leveling Cap
Seat Post Knob
M8 Locknut
Idler
Seat
Upright
M4 x 20mm Screw
Frame Bushing
Console
Left Shield
Right Shield
Resistance Control/Cable
Seat Post Bushing
Crank/Pulley
Clamp
Extension Wire
Left Pedal/Strap
Spring
Right Pedal/Strap
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
*
*
1
2
1
4
2
2
2
3
1
1
1
2
1
1
7
1
3
1
1
6
1
7
2
3
–
–
Description
3/8" Nut
U-bracket
Lower Resistance Cable
M8 x 60mm Patch Screw
Eyebolt
M6 Locknut
M10 x 70mm Patch Screw
M8 x 15mm Patch Screw
Drive Belt
Crank Bearing Set
Flywheel
Magnet
Reed Switch/Wire
M8 x 20mm Bolt
M4 x 25mm Screw
Handlebar
Flywheel Nut
M5 x 50mm Button Screw
M8 Washer
M4 x 15mm Button Screw
M5 x 15mm Screw
M4 x 15mm Screw
M8 x 65mm Bolt
M8 Split Washer
Userʼs Manual
Assembly Tool
R0710A
Note: Specifications are subject to change without notice. For information about ordering replacement parts, see
the back cover of this manual. *These parts are not illustrated.
18
EXPLODED DRAWING—Model No. WLEX31310.0
16
R0710A
14
46
46
18
44
48
13
42
7
10
34
49
33
4
14
41
19
3
34
50
2
4
12
23
47
1
39
21
5
48
50 15
10
48
20
22
46
41
46
41
19
32
29
25
45
31
28
36
38
11 40
10
17 27
38
9
24
41
26
43
8
30
6
8
31
28
37
43
35
43
32
ORDERING REPLACEMENT PARTS
To order replacement parts, please see the front cover of this manual. To help us assist you, be prepared to
provide the following information when contacting us:
• the model number and serial number of the product (see the front cover of this manual)
• the name of the product (see the front cover of this manual)
• the key number and description of the replacement part(s) (see the PART LIST and the EXPLODED
DRAWING near the end of this manual)
LIMITED WARRANTY
IMPORTANT: You must register this product within 30 days of the purchase date to avoid added
fees for service needed under warranty. Go to www.wesloservice.com/registration.
ICON Health & Fitness, Inc. (ICON) warrants this product to be free from defects in workmanship and
material, under normal use and service conditions. Parts and labor are warranted for ninety (90) days from
the date of purchase.
This warranty extends only to the original purchaser. ICONʼs obligation under this warranty is limited to
repairing or replacing, at ICONʼs option, the product through one of its authorized service centers. All
repairs for which warranty claims are made must be preauthorized by ICON. If the product is shipped to
a service center, freight charges to and from the service center will be the customerʼs responsibility. For
replacement parts shipped while the product is under warranty, the customer will be responsible for a minimal handling charge. For in-home service, the customer will be responsible for a minimal trip charge. This
warranty does not extend to any damage to a product caused by or attributable to freight damage, abuse,
misuse, improper or abnormal usage, or repairs not provided by an ICON authorized service center; to
products used for commercial or rental purposes or as store display models; or to products transported
or purchased outside the US. No other warranty beyond that specifically set forth above is authorized by
ICON.
ICON is not responsible or liable for indirect, special, or consequential damages arising out of or in connection with the use or performance of the product; damages with respect to any economic loss, loss of
property, loss of revenues or profits, loss of enjoyment or use, or costs of removal or installation; or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties, and any implied warranties of
merchantability or fitness for a particular purpose are limited in their scope and duration to the terms set
forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the
above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights that vary from state to state.
ICON Health & Fitness, Inc., 1500 S. 1000 W., Logan, UT 84321-9813
Part No. 301767 R0710A
Printed in China © 2010 ICON IP, Inc.