Quadra-Fire 2100 Millennium Owner`s manual

2100 MILLENNIUM WOOD STOVE
Automatic Combustion Control (ACC)
Owner’s Manual
Installation and Operation
Tested and
Listed by
O-T L
C
Portland
Oregon USA
US
OMNI-Test Laboratories, Inc.
Model:
21M-ACC
NOTICE
DO NOT DISCARD THIS MANUAL
• Important operating
and maintenance
instructions included.
• Read, understand and
follow these instructions
for safe installation and
operation.
WARNING
WARNING
If the information in these instructions is not followed exactly, a
fire may result causing property
damage, personal injury, or death.
• Do not store or use gasoline or other flammable vapors and liquids in the vicinity of
this or any other appliance.
• Do not overfire - If heater or chimney connector glows, you are overfiring. Overfiring
will void your warranty.
• Comply with all minimum clearances to
combustibles as specified. Failure to
comply may cause house fire.
WARNING
HOT SURFACES!
Glass and other surfaces are
hot during operation AND
cool down.
Hot glass will cause burns.
• Do not touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• CAREFULLY SUPERVISE children in same room
as fireplace.
• Alert children and adults to hazards of high
temperatures.
High temperatures may ignite clothing or other
flammable materials.
• Keep clothing, furniture, draperies and other
flammable materials away.
Fire Risk.
NOTE
For use with solid wood fuel only.
Other fuels may overfire and generate
poisonous gases (i.e. carbon monoxide).
To obtain a French translation of this manual, please
contact your dealer or visit www.quadrafire.com
Installation and service of this appliance should
be performed by qualified personnel. Hearth &
Home Technologies recommends NFI certified
professionals, or technicians supervised by an
NFI certified professional.
www.quadrafire.com
• Leave this manual with
party responsible for
use and operation.
D
DI O N
SC O
AR T
D
Pour obtenir une traduction française de ce manuel,
s’il vous plaît contacter votre revendeur ou visitez
www.quadrafire.com
7039-131I
February 20, 2011
2100 Millennium Wood Stove (ACC)
and Welcome to the Quadra-Fire Family!
Hearth & Home Technologies welcomes you to our tradition of excellence! In choosing a Quadra-Fire appliance,
you have our assurance of commitment to quality, durability, and performance.
our stoves, inserts and fireplaces. And yet we are old-fashioned when it comes to craftsmanship. Each unit is meticulously fabricated and surfaces are hand-finished for lasting
beauty and enjoyment. Our pledge to quality is completed
as each model undergoes a quality control inspection.
This commitment begins with our research of the market,
including ‘Voice of the Customer’ contacts, ensuring we
make products that will satisfy your needs. Our Research
and Development facility then employs the world’s most
advanced technology to achieve the optimum operation of
We wish you and your family many years of enjoyment in the
warmth and comfort of your hearth appliance. Thank you for
choosing Quadra-Fire.
NOTE: Clearances may only be
reduced by means approved by the
regulatory authority having jurisdiction
WHILE IN OPERATION DO NOT TOUCH, KEEP CHILDREN AND CLOTHING AWAY. CONTACT MAY CAUSE SKIN BURNS.
CAUTION: HOT
FURNISHINGS AND OTHER COMBUSTIBLE MATERIAL FAR AWAY FROM THE APPLIANCE. SEE NAMEPLATE AND INSTRUCTIONS
KEEP
CHAUD LORS DE L'OPÉRATION. NE PAS TOUCHER. GARDEZ LES ENFANTS ET LES VÊTEMENTS LOIN DE L'ESPACE DÉSIGNÉ DE L'INSTALLATION. LE CONTACT PEUT CAUSER DES
ATTENTION: BRÛLURES À LA PEAU. GARDEZ LES MEUBLES ET LES MATÉRIAUX COMBUSTIBLES LOIN DE L'ESPACE DÉSIGNÉ DE L'APPAREIL. VOIR L'ÉTIQUETTE ET LES INSTRUCTIONS.
APPAREIL DE CHAUFFAGE DE PIÈCE, DE TYPE DE
COMBUSTIBLE SOLIDE, POUR USAGE DANS LES
LISTED ROOM HEATER, SOLID FUEL TYPE.
MAISONS MOBILES. (UM) 84-64 HUD. "Pour Usage
ALSO FOR USE IN MOBILE HOMES. (UM) 84 HUD . Avec Bois Solide Seulement"
"For Use with Solid Wood Fuel Only"
PREVENT HOUSE FIRES
PRÉVENTION DES FEUX DE MAISON
Install and use only in accordance with
manufacturer's installation and operating
instructions. Contact local building or fire officials
about restrictions and installation inspections in
your area. Do not obstruct the space beneath
heater.
WARNING - For Mobile Homes: Do not install in
a sleeping room. An outside combustion air inlet
must be provided and unrestricted while unit is in
use. The structural integrity of the mobile home
floor, ceiling and walls must be maintained. The
stove needs to be properly grounded to the frame
of the mobile home. Components required for
mobile home installation: Outside Air Kit, Part
Number OAK-ACC.
Refer to manufacturer's instructions and local
codes for precautions required for passing
chimney through a combustible wall or ceiling and
maximum offsets.
Inspect and clean chimney frequently - Under
Certain Conditions of Use, Creosote Buildup May
Occur Rapidly.
Do not connect this unit to a chimney serving
another appliance.
Optional Components: Optional Blower, Part
BK-ACC.
Electrical Rating: 115 VAC, 1.2 Amps, 60 Hz.
Route power cord away from unit. Do not route
cord under or in front of appliance.
DANGER: Risk of electrical shock. Disconnect
power supply before servicing.
Replace glass only with 5mm ceramic available
from your dealer.
Do not use grate or elevate fire. Build wood fire
directly on hearth.
Do not overfire - if heater or chimney connector
glows, you are overfiring.
Operate only with the fuel loading door closed.
Open only to add fuel to the fire.
Installez et utilisez en accord avec les instructions
d'installation et d'opération du fabricant. Contactez le bureau
de la construction ou le bureau des incendies au sujet des
restrictions et des inspections d'installation dans votre
voisinage. Ne pas obstruez l'espace en dessous de l'appareil.
AVIS - Pour Les Maisons Mobiles: Ne pas installer dans une
chambre à coucher. Un tuyau extérieur de combustion d'air
doit être installé et ne doit pas être obstrué lorsque l'appareil
est en usage. La structure intégrale du plancher, du plafond et
des murs de la maison mobile doit être maintenue intacte.
L'appareil de chauffage doit être fixé à la charpente de la
maison mobile. Les composants requis pour l'installation des
maisons mobiles: Assemblage d'air extérieur, Numéro de
Pièce OAK-ACC.
Référez vous aux instructions du fabricant et des codes
locaux pour les précautions requises pour passer une
cheminée à travers un mur ou un plafond combustibles, et les
compensations maximums.
Inspectez et nettoyez la cheminée fréquemment. Sous
certaines conditions, il se peut que la créosote s'accumule
rapidement.
Ne pas connecter cet appareil à une cheminée servant un
autre appareil.
Composants Optionnels: Ventilateur Optionnel, Pièce
BK-ACC.
Puissance Électrique: 115 VAC, 1.2 Amps, 60 Hz.
Éloignez le fil électrique de l'appareil. Ne pas faire passer le fil
électrique au dessus ou en dessous de l'appareil.
DANGER: Il y a risque de décharge électrique. Déconnectez
le fil électrique de la prise de contact avant le service.
Remplacez la vitre seulement avec une vitre céramique de 5
mm disponible chez votre fournisseur.
N'élevez pas le feu. Bâtissez le feu de bois directement sur
l'âtre.
Ne pas surchauffer. Si l'appareil de chauffage ou le tuyau de
cheminée rougissent, vous surchauffez.
Opérez l'appareil seulement lorsque la porte de chargement
est fermée. Ouvrez la porte seulement lorsque vous devez
ajouter des combustibles dans le feu.
FLOOR PROTECTION:
PROTECTION DU PLANCHER:
Floor protector must be a 3/8 (9.5mm) inch min.
thickness, non-combustible material or equivalent,
extending beneath heater and to front/sides/rear as
indicated on the diagram below. Exception:
Non-combustible floor protections must extend
beneath the flue pipe when installed with horizontal
venting and extend 2 inches (51mm) beyond each
side.
Le protecteur de plancher doit être d'un minimum de 3/8 inch
(9.5mm) d'épaisseur, de matériel incombustible ou
équivalent, s'étendant du dessous de l'appareil de chauffage
à l'avant, aux cotés et à l'arrière comme indiqué sur le
diagramme suivant. Exception: Les protections
incombustibles du plancher doivent s'étendre en dessous du
conduit de cheminée lorsqu'installées avec une ventilation à
l'horizontale et s'étendre de 2 inches (51mm) de chaque
côté.
203mm (8 in.)
Tested and
Listed by
O-T L
SERIAL NO. / NUMÉRO DE SÉRIE
Portland
Oregon USA
2100 Millennium ACC 007004
R
US
C
OMNI-Test Laboratories, Inc.
Report / Rapport
#061-S-70-6
TESTED TO:/ TESTÉ À:
UL 1482, ULC S627-00.
VENT SPECIFICATIONS:
SPÉCIFICATIONS DE LA VENTILATION:
SINGLE WALL: Six inch (6 inches) (152mm) diameter, minimum 24 MSG black or
blued steel connector pipe, with a listed factory-built UL103HT* Class "A" chimney,
suitable for use with solid fuels, or a masonry chimney, and the referenced clearances.
DOUBLE WALL: Six inch (6 inches) (152mm) diameter, listed double wall air
insulated connector pipe with listed factory-built UL103HT* Class "A" chimney, or a
masonry chimney and the referenced clearances
*In Canada must comply with Standard CAN/ULC-S629-M87 for the 650 degree
Factory-built chimneys.
MOBILE HOME: Use double wall pipe by Dura-Vent DVL, Selkirk Metalbestos DS or
Security DL double wall connector pipe. Must be equipped with a spark arrestor.
Apply double wall clearances below when installing unit.
MUR SIMPLE: De six (6 inches) (152mm) de diamètre le connecteur de conduit de
minimum d'acier noir ou bleu de minimum de 24MSG, avec une cheminée bâtit en
usine UL103HT* de Classe "A", adéquate pour usage avec les combustions solides,
ou une cheminée de briques, avec espaces libres référés.
MUR DOUBLE: De six (6 inches) (152mm) de diamètre, le connecteur du conduit
d'air isolé pour mur double avec une cheminée bâtit en usine UL103HT* de Classe
"A, ou une cheminée de briques, avec espaces libres alloués.
*Au Canada doit conformer a CAN/ULC-S629-M87 la norme pour 650 degré C cheminée
bâtit en usine.
MAISON MOBILE: Utiliser un conduit de mur double par Dura-Vent DVL, Selkirk
Metalbestos DS ou Security DL. Doit être équipé d'un arrêt d'étincelle. Utiliser les
espaces libres pour mur double comme mentionné ci-bas.
ESPACES LIBRES MINIMUM DES MATÉRIAUX COMBUSTIBLES En Pouces &
(millimètres)
MINIMUM CLEARANCES TO COMBUSTIBLES In Inches & (Millimeters)
NOTE:
Toutes les dimensions "A", "C", et "F" sont à partir du diamètre intérieur de
NOTE: All "A" , "C" and "F" Dimensions are to inside diameter of the flue collar.
l'entrée du conduit.
INSTALLATION: FULL VERTICAL / ENTIÈREMENT VERTICALE
A
B
C
D
E
F
G
H
SINGLE WALL PIPE
15 (381)
8.5 (216)
17 (432)
56 (1422)
N/A
CONDUIT DU MUR SIMPLE
DOUBLE WALL PIPE
8.75 (222) 5.75 (146) 20 (508) 10.5 (267) 7.5 (191)
16 (406)
43 (1092)
N/A
CONDUIT DU MUR DOUBLE
11 (279) 21.5 (546) 13 (330)
2-1/4 in."
36 in.
minimum
Fuel loading door
16" from glass
8 in.
USA
29-5/8 in.
minimum
14 (356) 10 (254) 20.5 (521) 12 (305)
8.5 (216)
17 (432)
56 (1422) 9.5 (241) CONDUIT DU MUR SIMPLE
DOUBLE WALL PIPE
9.5 (241) 5.5 (140) 21.5 (546) 13 (330)
7.5 (191)
16 (406)
43 (1092)
1445 N. Highway, Colville, WA 99114
www.quadrafire.com
1168mm
(46 in.)
minimum
INSTALLATION: ALCÔVE - De six (6 inches) (152mm) de diamètre, le connecteur du conduit d'air isolé pour mur double avec une cheminée bâtit en usine 103HT de Classe "A", ou une
cheminée de briques. (Les maisons mobiles doivent être équipées d'un arrêt d'étincelle). La profondeur maximum de l'alcôve ne doit pas être de plus de 48 inches (1220mm) avec une
hauteur minimum de 43 inches (1092mm) du haut de l'appareil, et des espaces libres alloués.
CORNER INSTALLATION
INSTALLATION DU COIN
E
9.5 (241) 5.5 (140) 21.5 (546) 13.5 (343)
ALCOVE SIDE VIEW /
VUE DE CÔTÉ DE L'ALCÔVE
N/A
N/A
G
F
43 (1092) 5 (127) CONDUIT DU MUR DOUBLE
E
ALCOVE TOP VIEW /
VUE DU HAUT DE L'ALCÔVE
H
F
A
C
B
D
STOVE TO CEILING CLEARANCE
ESPACE LIBRE DU POÊLE AU PLAFOND
CANADA
1078mm (42-7/16 in.)
minimum
Fabriqué aux
États-Unis-d’Amérique par des
pièces d’origine américaine et
pièces importées.
D
5 (127) CONDUIT DU MUR DOUBLE
INSTALLATION: ALCOVE - Six inch (6 inches) (152mm) diameter listed DOUBLE WALL air insulated connector pipe with UL 103 HT listed factory-built
Class "A" chimney, or a masonry chimney. (Mobile Home must be equipped with a spark arrestor.) Maximum depth of Alcove shall be no more than 48
inches (1220mm) with a minimum height of 43 inches (1092mm) to top of unit, and the referenced clearances.
DOUBLE WALL PIPE
B
C
SINGLE WALL PIPE
457mm (18 in.)
Made in U.S.A. of US and
imported parts.
Manufactured by:
Fabriqué par:
Page 2
203mm
(8 in.)
203mm
(8 in.)
A
INSTALLATION: HORIZONTAL WITH MINIMUM 2 FT VERTICAL OFF STOVE TOP
INSTALLATION: HORIZONTALE AVEC 609mm VERTICAL MINIMUM DU HAUT DU POÊLE
G
5-3/4 in.
BACKWALL/SIDEWALL
MUR ARRIÈRE/MUR DE CÔTÉ
2010 2011 2012 Jan. Feb. Mar. Apr. May June July Aug. Sept. Oct. Nov. Dec. U.S. ENVIRONMENTAL PROTECTION AGENCY - Certified to
comply with July 1990 particulate emission standards.
DO NOT REMOVE THIS LABEL / NE PAS ENLEVER L'ÉTIQUETTE
7039-131I
7039-134F
February 20, 2011
Mat
Cop
Back
Size
2100 Millennium Wood Stove (ACC)
Safety Alert Key:
• DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.
• WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.
• CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
• NOTICE: Indicates practices which may cause damage to the fireplace or to property.
TABLE OF CONTENTS
Section 8: Operating Instructions
Section 1: Listing and Code Approvals
A.
B.
C.
D.
Appliance Certifications.......................4
Mobile Home Approved.......................4
Glass Specifications.............................4
BTU & Efficiency Specifications...........4
Section 2: Getting Started
A.
B.
C.
D.
E.
F.
G.
H.
Design, Installation & Location
Considerations.....................................5
Fire Safety...........................................5
Negative Pressure...............................6
Flue Draft Considerations....................7
Venting Systems..................................7
Tools and Supplies Needed................7
Inspect Appliance & Components.......7
Typical Stove System..........................8
Section 9: Maintaining & Servicing Appliance
Section 3: Dimensions & Clearances
A. Appliance Dimensions.........................9
B. Clearances to Combustibles................10
Section 4: Installation Consideration
A. Hearth Requirements..........................11
B. Outside Air...........................................12
C. Blower Installation................................13
Section 5: Chimney Requirements
A.
B.
C.
D.
E.
A. Overfiring Your Appliance....................20
B. Wood Selection & Storage...................20
C. Burning Process...................................20-21
D.
Automatic Combustion Control (ACC).....21
E. Air Controls..........................................21-22
F. Burn Rates & Operating Efficiency......22
G. Building A Fire......................................23
H. Correct Baffle & Blanket Placement.....24
I. Blower Operating Instructions..............25
J. Opacity (Smoke)..................................25
K. Frequently Asked Questions................26
A. Quick Reference Maintenance Guide..27
B. General Maintenance & Cleaning........28
C. Glass Replacement..............................29
D. Firebrick Replacement.........................30
E. Baffle Removal.....................................31
F. Snap Disc Replacement......................31
G. Tube Channel Replacement................32
Section 10: Troubleshooting.........................33
Section 11: Reference Material
Venting Components...........................14
Chimney Systems................................14-16
Installing Chimney Components..........16
Chimney Termination Requirements...17
2-10-3 Rule...........................................17
A.
B.
C.
D.
E.
F.
Exploded Drawings..............................34
Service Parts & Accessories...............35-37
Service & Maintenance Log.................38-39
Homeowner’s Notes............................40-41
Warranty Policy....................................42-43
Contact Information..............................44
Section 6: Mobile Home................................18
Section 7: Appliance Set-Up
A. Door Handle Assembly........................19
B. Blower Speed Adjustment...................19
February 20, 2011
7039-131I
Page 3
1
2100 Millennium Wood Stove (ACC)
Listing and Code Approvals
D. BTU & Efficiency Specifications
A. Appliance Certification
Model:
2100 Millennium (ACC)
EPA Certified:
Laboratory:
OMNI Test Laboratories, Inc.
Report No & Date:
061-S-70-6
EPA Certificate Number Number: 664
Issued: 07-20-2007
and Date:
Type:
Listed Room Heater, Solid Fuel Type
Standard:
UL1482 and ULC S627-00 and
(UM) 84-HUD, Mobile Home
Approved.
NOTE: This installation must conform with local codes. In the
absence of local codes you must comply with the UL1482, (UM)
84-HUD and NPFA211 in the U.S.A. and the ULC S627-00 and
CAN/CSA-B365 Installation Codes in Canada.
Efficiency:
78.5%
BTU Output:
12,000 to 28,800
Heating Capacity:
800 to 1,500 sq ft
depending on climate zone
Vent Size:
6 inches
Firebox Size:
1.46 cubic feet
Max Wood Length:
16 inches
Fuel:
Cord Wood
Shipping Weight:
300 lbs
WARNING
The Quadra-Fire 2100 Millennium Wood Stove (ACC) meets
the U.S. Environmental Protection Agency’s 1990 particulate
emission standards.
B. Mobile Home Approved
• This appliance is approved for mobile home installations
when not installed in a sleeping room and when an outside combustion air inlet is provided.
• The structural integrity of the mobile home floor, ceiling,
and walls must be maintained.
• The appliance must be properly grounded to the frame
of the mobile home with #8 copper ground wire, and use
only listed double-wall connector pipe.
• Outside Air Kit, part OAK-ACC must be installed in a mobile home installation.
2.1 grams per hour
Fire Risk.
•
•
•
•
•
•
•
Hearth & Home Technologies disclaims any
responsibility for, and the warranty will be
voided by, the following actions:
Installation and use of any damaged appliance.
Modification of the appliance.
Installation other than as instructed by Hearth & Home
Technologies.
Installation and/or use of any component part not approved
by Hearth & Home Technologies.
Operating appliance without fully assembling all
components.
Operating appliance without legs attached (if supplied with
unit).
Do NOT Overfire - If appliance or chimney connector glows,
you are overfiring.
Any such action that may cause a fire hazard.
C. Glass Specifications
This stove is equipped with 5mm ceramic glass. Replace
glass only with 5mm ceramic glass. Please contact your
dealer for replacement glass.
Quadra-Fire is a registered trademark of Hearth & Home
Technologies.
Page 4
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage.
For assistance or additional information, consult a qualified
installer, service agency or your dealer.
NOTE: Hearth & Home Technologies, manufacturer of
this appliance, reserves the right to alter its products,
their specifications and/or price without notice.
7039-131I
February 20, 2011
2
2100 Millennium Wood Stove (ACC)
Getting Started
A. Design, Installation & Location Considerations
B. Fire Safety
Consideration must be given to:
To provide reasonable fire safety, the following should be
given serious consideration:
•
•
•
•
Safety
Convenience
Traffic flow
Chimney and chimney connector required
It is a good idea to plan your installation on paper, using exact
measurements for clearances and floor protection, before
actually beginning the installation. If you are not using an
existing chimney, place the appliance where there will be a
clear passage for a factory-built listed chimney through the
ceiling and roof.
We recommend that a qualified building inspector and your
insurance company representative review your plans before
and after installation
If this appliance is in an area where children may be near it
is recommended that you purchase a decorative barrier to go
in front of the appliance. Remember to always keep children
away while it is operating and do not let anyone operate
this appliance unless they are familiar with these operating
instructions.
1. Install at least one smoke detector on each floor of
your home to ensure your safety. They should be
located away from the heating appliance and close
to the sleeping areas. Follow the smoke detector
manufacturer’s placement and installation instructions,
and be sure to maintain regularly.
2.
A conveniently located Class A fire extinguisher
to contend with small fires resulting from burning
embers.
3.
A practiced evacuation plan, consisting of at least two
escape routes.
4.
A plan to deal with a chimney fire as follows:
In the event of a chimney fire:
a
b.
Evacuate the house immediately
Notify fire department
WARNING
NOTE: Service Space
Fire Risk.
In order to replace the tube channel a clearance of 17
inches (432mm) is required on the right side of stove in
order to remove the tubes with the stove in place.
If space is not available, the stove will have to be disconnected from the chimney to proceed with the tube replacement. See page 32.
•
•
•
•
CAUTION
Check building codes prior to installation.
•
• Installation MUST comply with local, regional, state and
national codes and regulations.
•
• Consult insurance carrier, local building, fire officials or
authorities having jurisdiction about restrictions, installation
inspection, and permits.
•
Hearth & Home Technologies disclaims any
responsibility for, and the warranty will be
voided by, the following actions:
Installation and use of any damaged appliance.
Modification of the appliance.
Installation other than as instructed by Hearth & Home
Technologies.
Installation and/or use of any component part not approved
by Hearth & Home Technologies.
Operating appliance without fully assembling all
components.
Operating appliance without legs attached (if supplied with
unit).
Do NOT Overfire - If appliance or chimney connector glows,
you are overfiring.
Any such action that may cause a fire hazard.
WARNING
Asphyxiation Risk.
• DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVICING ANOTHER APPLIANCE.
• DO NOT CONNECT TO ANY AIR DISTRIBUTION DUCT OR SYSTEM.
May allow flue gases to enter the house.
February 20, 2011
7039-131I
WARNING
Fire Risk.
• Do not operate appliance before reading and
understanding operating instructions.
• Failure to operate appliance properly may
cause a house fire.
Page 5
2100 Millennium Wood Stove (ACC)
C. Negative Pressure
Draft is the pressure difference needed to vent appliances
successfully. Considerations for successful draft include:
To minimize the affects of negative air pressure the following
must be considered:
• Preventing negative pressure
• Location of appliance and chimney
• Install the outside air kit. Install the intake on the
side of the house towards prevailing winds during the
heating season.
• Ensure adequate outdoor air is supplied for combustion appliances and exhaust equipment.
• Ensure furnace and air conditioning return vents are
not located in the immediate vicinity of the appliance,
• Avoid installing the appliance near doors, walkways
or small isolated spaces.
• Recessed lighting should be of “sealed can” design;
attic hatches weather stripped or sealed; and attic
mounted ductwork and air handler joints and seams
taped or sealed.
Negative pressure results from the imbalance of air available for the stove to operate properly. Causes for this imbalance include:
• Exhaust fans (kitchen, bath) etc.)
• Range hoods
• Combustion air requirements for furnaces, water
heaters and other combustion appliances
• Clothes dryers
• Location of return-air vents to furnace or air conditioning
• Imbalances of HVAC air handling system
• Upper level air leaks
• Recessed lighting
• Attic hatch opening
• Duct leaks
WARNING
Asphyxiation Risk.
• Negative pressure can cause spillage of combustion fumes, soot and carbon monoxide.
• Appliance needs to draft properly for safety.
Recommended Location:
• Above peak
Recommended Location:
• Above peak
• Inside heated space
Marginal Location:
• Wind loading possible
Marginal Location:
• Below peak
Location NOT recommended:
• Not the highest point of the roof
• Wind loading possible
Location NOT recommended:
• Too close to tree
• Below adjacent structure
• Lower roof line
• Avoid outside wall
Recommended:
• Insulated exterior chase
in cooler climates
Windward
Leeward
Recommended:
Outside Air Intake
on windward side
Multi-level Roofs
NOT recommended:
Outside Air Intake
on leeward side
Figure 6.1
Page 6
7039-131I
February 20, 2011
2100 Millennium Wood Stove (ACC)
D. Flue Draft Considerations
F. Tools And Supplies Needed
Location of the appliance and chimney will affect performance. As shown in Figure 6.1 on page 6 the chimney
should:
Before beginning the installation be sure that the following
tools and building supplies are available.
• Be installed through the warm space enclosed by the
building envelope. This helps to produce more draft,
especially during lighting and die down of the fire.
• Penetrate the highest part of the roof. This minimizes
the affects of wind turbulence and down drafts.
• Consider the appliance location in order to avoid
floor and ceiling attic joists and rafters.
Exterior conditions such as roof line, surrounding trees,
prevailing winds and nearby hills can influence stove
performance. Your local dealer is the expert in your geographic
area and can usually make suggestions or discover solutions
that will easily correct your flue problem.
To be sure that your appliance burns properly, the chimney
draft (static pressure) should be approximately -.04 inch water
column (W.C.) during a low burn and -.10 inch W.C. during a
high burn, measured 6 inches (152mm) above the top of the
appliance after one hour of operation at each burn setting.
NOTE: These are guidelines only, and may vary somewhat
for individual installations.
E. Venting Systems
The venting system consists of a chimney connector (also
known as stove pipe) and a chimney. These get extremely
hot during use. Temperatures inside the chimney may
exceed 2000°F (1100°C) in the event of a creosote fire. To
protect against the possibility of a house fire, the chimney
connector and chimney must be properly installed and
maintained. An approved thimble must be used when a
connection is made through a combustible wall to a chimney.
A chimney support package must be used when a connection
is made through the ceiling to a prefabricated chimney.
These accessories are absolutely necessary to provide
safe clearances to combustible wall and ceiling material.
Follow venting manufacturer’s clearances when installing
venting system.
Reciprocating saw
Pliers
Hammer
Phillips Head Screwdriver
Flat Blade Screwdriver
Plumb Line
Level
Tape Measure
G. Inspect Appliance & Components and
Pre-Burn Check List
1.
Place the appliance in a location near the final
installation area and follow the procedures below:
2.
Open the appliance and remove all the parts and
articles packed inside the Component Pack. Inspect
all the parts and glass for shipping damage. Contact
your dealer if any irregularities are noticed.
3.
All safety warnings have been read and followed.
4.
This Owner’s Manual has been read.
5.
Floor protection requirements have been met.
6.
Venting is properly installed.
7.
The proper clearances from the appliance and chimney to combustible materials have been met.
8.
The masonry chimney is inspected by a professional
and is clean, or the factory built metal chimney is
installed according to the manufacturer’s instructions and clearances.
9.
The chimney meets the required minimum height.
10.
All labels have been removed from the glass door.
11.
A power outlet is available nearby if installing
optional blower assembly.
WARNING
WARNING
Asphyxiation Risk.
• DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVICING ANOTHER APPLIANCE.
• DO NOT CONNECT TO ANY AIR DISTRIBUTON DUCT OR SYSTEM.
May allow flue gases to enter the house.
February 20, 2011
Framing Material
Hi-Temp Caulking Material
Gloves
Framing Square
Electric Drill & Bits (1/4”)
Safety Glasses
1/2 in. - 3/4 in. length, #6 or
#8 self drilling screws (need 3
per pipe section connection)
7039-131I
Fire Risk.
Inspect appliance and components for damage.
Damaged parts may impair safe operation.
• Do NOT install damaged components.
• Do NOT install incomplete components.
• Do NOT install substitute components.
Report damaged parts to dealer.
Page 7
2100 Millennium Wood Stove (ACC)
Spark Arrestor Cap
H. Typical Stove Systems
Fireclay Flue Liner
With Air Space
Concrete Cap
Stove system with masonry chimney
consists of:
Rafter
• Stove
• Chimney Connector (stove pipe)
• Thimble
• Masonry Chimney
• Hearth Pad Floor Protection
Flashing
1" (25mm) Clearance
With Firestop
Ceiling Joist
Eave
Combustible Wall
Thimble,
12" (305mm)
Of Brick
Sheathing
Outside Air Rear Vent
Outside Air
Termination Cap
Floor
Protector
Airtight
Cleanout Door
Figure 8.1 Masonry Chimney
Stove system with prefabricated
metal chimney consists of:
Listed Termination Cap
• Stove
• Firestops
• Insulations Shields
Fireclay Flue Liner
With Air Space
Concrete Cap
• Chimney Connector
(stove pipe)
• Thimble (for exterior
chimney)
Storm Collar
Spark Arrestor Cap
Flashing
Rafter
Flashing
1" (25mm) Clearance
With Firestop
Listed Chimney
Ceiling Joist
Eave
Combustible Wall
• Storm Collar and Flashing
• Termination Cap
• Hearth Pad Floor Protection
Thimble,
12" (305mm)
Of Brick
Ceiling Support
Sheathing
Outside Air Rear Vent
Chimney
Connector
Outside Air
Termination Cap
Floor
Protector
Airtight
Cleanout Door
Floor
Protector
Figure 8.2 Exterior Prefabricated Chimney
Page 8
7039-131I
Figure 8.3 Interior Prefabricated Chimney
February 20, 2011
3
2100 Millennium Wood Stove (ACC)
Dimensions and Clearances
A. Appliance Dimensions
23-3/8 in. (594mm)
CL
8-5/8 in.
(219mm)
NOTE: Flue Collar size is 6 inch
(152mm) diameter (ID)
11-11/16 in.
(297mm)
9-1/4 in. (235mm)
13-1/2 in. (342mm)
12-3/4 in.
(324mm)
17 in. (432mm)
27-15/16 in.
(709mm)
Figure 9.1 Front View
26-7/16 in. (671mm)
24-5/16 in. (618mm)
6-11/16 in.
(170mm)
CL
11-1/2 in.
(292mm)
16 in. (406mm)
CL
20-3/4 in. (527mm)
4-1/2 in
(108mm)
Outside Air
Connection
Figure 9.2 Side View
February 20, 2011
7039-131I
Page 9
2100 Millennium Wood Stove (ACC)
B. Clearances to Combustibles (UL and ULC)
BACKWALL / SIDEWALL
A
ALCOVE SIDE VIEW
NOTE: Clearances may only be reduced by means
approved by the regulatory authority having jurisdiction
B
G
C
D
A
B
H
STOVE TO CEILING
CLEARANCE
CORNER INSTALLATION
G
ALCOVE TOP VIEW
E
F
C
E
D
F
MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS In Inches & (Millimeters)
NOTE: All "A" , "C" and "F" Dimensions are to the inside diameter of the flue collar.
A
B
C
D
E
F
G
H
INSTALLATION: Full Vertical
SINGLE WALL PIPE
15 (381)
DOUBLE WALL PIPE
8.75(222) 5.75 (146) 20 (508) 10.5 (267)
11 (279) 21.5 (546) 13 (330)
8.5 (216) 17(432)
7.5 (191)
56 (1422)
N/A
16 (406) 43 (1092)
N/A
INSTALLATION: Horizontal with Minimum 2 Foot Vertical Off Stove Top
SINGLE WALL PIPE
14 (356)
DOUBLE WALL PIPE
9.5 (241) 5.5 (140) 21.5 (546) 13 (330)
10 (254) 20.5 (521) 12 (305)
8.5 (216) 17 (432)
7.5 (191)
56 (1422)
16 (406) 43 (1092)
9.5 (241)
5 (127)
INSTALLATION: ALCOVE
Six inch (6") (152mm) diameter listed double wall air insulated connector pipe with UL
103 HT listed factory-built Class "A" chimney, or a masonry chimney. (Mobile Home must be equipped with a spark
arrestor). Maximum depth of alcove shall be no more than 48"(1220mm) with a minimum height of 43" (1092mm) to top
of unit, and the referenced clearances.
DOUBLE WALL PIPE
9.5 (241)
5.5 (140) 21.5 (546) 13 (330)
WARNING
Fire Risk.
• Comply with all minimum clearances to
combustibles as specified.
• Failure to comply may cause house fire.
Page 10
N/A
N/A
43 (1092)
5 (127)
NOTE: Service Space
In order to replace the tube channel assembly a clearance
of 17 inches (432mm) is required on the right side of stove
in order to remove the tubes with the stove in place.
If space is not available, the stove will have to be disconnected from the chimney to proceed with the tube replacement.
7039-131I
February 20, 2011
4
2100 Millennium Wood Stove (ACC)
Installation
A. Hearth Protection Requirements
FLOOR PROTECTION: Floor protector must be non-combustible material, extending beneath heater and to the front,
sides and rear as indicated. The floor must be non-combustible or otherwise adequately protected from radiant heat
given off by the unit and from sparks and falling embers. A
layer of thin brick or ceramic tile over a combustible floor is
not sufficient.
In Canada, similar floor protection must be provided 18
inches (457mm) in front and 8 inches (203mm) from the
sides and rear of the stove. *See exception.
*EXCEPTION: Non-combustible floor protections must
extend beneath the flue pipe when installed with horizontal
venting and extend 2 inches (51mm) beyond each side.
See Figure 11.4.
WARNING
In US installations, it is necessary to install a floor protector
of a minimum of 3/8 inch (9.5mm) thick metal clad millboard
or equivalent a minimum of 16 inches (406mm) in front of
glass and 8 inches (203mm) to both sides of the fuel loading
door. Open the door and measure 8 inches (203mm) from
the side edge of the opening in the face of the appliance.
*See exception.
Fire Risk.
• Hearth pads must be installed exactly as
specified.
High temperatures or hot embers may ignite
concealed combustibles.
29
-5
/8
in
.
o
co ptio
ve na
ra l
ge
50-3/4 in.
.
13
5°
39 in.
minimum
Fuel loading door
39
in
8 in.
in
.
16" from glass
32-7/8 in.
2-1/4 in."
5-3/4 in.
25
-3
/8
USA
29-5/8 in.
minimum
USA
Figure 11.1
3 in.
USA
Figure 11.3
USA required
Canada recommended
203mm (8 in.)
203mm
(8 in.)
203mm
(8 in.)
1244mm
(49 in.)
minimum
457mm (18 in.)
1000mm (39-3/8 in.)
minimum
Figure 11.2
CANADA
Must extend 2 in. (51mm) beyond
each side of pipe (shaded area)
Figure 11.4
NOTE: • Illustrations and photos reflect typical installations and are FOR DESIGN PURPOSES ONLY.
•Illustrations/diagrams are not drawn to scale.
• Actual installation may vary due to individual design preference
• Hearth & Home Technologies reserves the right to alter its products.
February 20, 2011
7039-131I
Page 11
2100 Millennium Wood Stove (ACC)
B. Outside Air Kit Installation
WARNING
A source of air (oxygen) is necessary in order for combustion to take place. Whatever combustion air is consumed
by the fire must be replaced. Air is replaced via air leakage
around windows and under doors. In homes that have tightly
sealed doors and windows, an outside air source is needed.
An optional Outside Air Kit is available.
Fire Risk.
Asphyxiation Risk.
Do not draw outside combustion air from:
• Wall, floor or ceiling cavity
• Enclosed space such as an attic or garage
Included in OAK-ACC:Termination cap, (2) wire ties, flex
• Close proximity to exhaust vents or chimneys
adapter, and fasteners
Fumes or odor may result
Included in SRV7033-041:Cover plate and sealing rope (see
WARNING
Floor Installation Alternative below,
Figure 12.2)
Asphyxiation Risk.
Items Needed for Installation (not supplied)
Outside air inlet must be located to prevent blockage
from:
• 4 inch flex aluminum pipe, or if using alternate material,
then it shall be made from durable, non-combustible, heat
resistant material up to 350oF. Cut the pipe to the required
length for your installation.
•Phillips head screw driver
•
Leaves
•
Snow or ice
•
Other debris
Block may cause combustion air starvation
•Silicone sealant
Smoke spillage may set off alarms or irritate sensitive
individuals.
• Drills and saws necessary for cutting holes through the
wall or flooring in your home
WARNING
1. Remove all materials from packing box.
Asphyxiation Risk.
Length of outside air supply duct shall NOT exceed
the length of the vertical height of the exhaust flue.
• Fire will not burn properly
• Smoke spillage occurs when door is opened due to
air starvation.
2. Using a #2 Phillips screw driver attach the flex adapter to
the stove using 4 screws. Figure 12.1.
3. For floor installations, remove circular “knock-out” in the
base of the pedestal. Figure 12.1.
4. Floor & Rear Installation: Cut a 4 inch (102mm) hole in
outside wall or floor to accommodate outside air piping.
Use 4 inch (102mm) aluminum metal flex or rigid piping
to directly connect outside air to appliance intake. Use
the supplied termination cap with a rodent screen. Seal
between the wall (or floor) and the pipe with silicone to
prevent moisture penetration.
5. Floor Installation Alternative: In some instances you
may not be able to install the flex pipe as show in Figure
12.1. If that is the case, you will need to order SRV7033041 which includes a cover plate and sealing rope as
shown in Figure 12.2. The goal is to seal the pedestal
so no room air can leak into the pedestal and to seal or
for cold air infiltration.
Flex Adapter
Wire Tie
Termination
Cap
For Floor Installations Remove
Circular “Knock-Out”
in Base of Pedestal.
Cover
Plate
Flex Line
Wire Tie
Figure 12.2 - Floor Installation Alternative
Figure 12.1 - Floor & Rear Installation
Page 12
7039-131I
February 20, 2011
2100 Millennium Wood Stove (ACC)
C. Blower (Optional)
CAUTION
1.Remove the 3 bolts (1/4”-20 Phillips head) on the outer
skin at the bottom rear of appliance.
Shock Risk.
• Do NOT remove grounding prong from plug.
• Plug directly into properly grounded 3 prong
receptacle.
• Route cord away from appliance.
• Do NOT route cord under or in front of appliance.
2.Align holes in mounting flange of blower with bolt holes in
appliance. Blower should be positioned at bottom of rear
outer skin as shown in Figure 13.1.
3.Re-insert and tighten bolts, securing blower onto outer
wall of appliance.
4.Place the bracket containing the snap disc and magnet
under the bottom left rear corner as shown in Figure 13.1.
See page 25 for detailed operating instructions for the
blower and snap disc.
Secure blower
with 3 bolts
Snap Disc
Bracket
with Magnet
Secure wires
with wire tie
MANUAL
MANUAL: Over-rides the
Snap Disc
FAN
AUTO
LOW
HIGH
AUTO: Fan will turn ON/OFF
Automatically by the Snap Disc
OFF
Controls the Fan Speed
Figure 13.1
3-1/8 in.
(80mm)
4-15/16 in.
(125mm)
4-13/16 in.
(122mm)
13-15/16 in. (355mm)
Figure 13.2 - Blower Housing Dimensions
February 20, 2011
7039-131I
Page 13
5
2100 Millennium Wood Stove (ACC)
Chimney Requirements
A. Venting Components
B. Chimney Systems
Chimney Connector:
Prefabricated Metal Chimney
It is also known as flue pipe or stove pipe. The chimney
connector joins the stove to the chimney. It must be a 6 inch
(152mm) minimum diameter 24 gauge mild steel black or
26 gauge blued steel, or an approved air-insulated double
wall venting pipe.
Thimble:
A manufactured or site-constructed device installed in
combustible walls through which the chimney connector
passes to the chimney. It is intended to keep the walls
from igniting. Site constructed thimbles must meet
NFPA 211 Standards. Prefabricated must be suitable
for use with selected chimney and meet UL103 Type HT
Standards. Follow instructions provided by the manufacturer
for manufactured thimbles for masonry chimney and
prefabricated chimneys.
•
Must be minimum 6 inch (152mm) diameter (ID) high
temperature chimney listed to UL 103 HT (2100oF) or
ULC S629M.
•
Must use components required by the manufacturer for
installation.
•
Must maintain clearances required by the manufacturer
for installation.
•
Refer to manufacturers instructions for installation.
NOTE: In Canada when using a factory-built chimney it must
be safety listed, Type UL103 HT (2100oF) CLASS “A” or
conforming to CAN/ULC-S629M, STANDARD FOR 650oC
FACTORY-BUILT CHIMNEYS.
Chimney:
Listed Termination Cap
The chimney can be new or existing, masonry or prefabricated
and must meet the following minimum requirements specified
in Section 5B.
Storm Collar
Flashing
Spark Arrestor Cap
Concrete Cap
Fireclay Flue Liner
With Air Space
Listed Chimney
Rafter
Flashing
1" (25mm) Clearance
With Firestop
Ceiling Joist
Eave
Combustible Wall
Thimble,
12" (305mm)
Of Brick
Ceiling Support
Chimney
Connector
Sheathing
Outside Air Rear Vent
Floor
Protector
Outside Air
Termination Cap
Airtight
Cleanout Door
Figure 14.2 - Prefabricated Interior Chimney
Figure 14.1 Prefabricated Exterior Chimney
Page 14
Floor
Protector
7039-131I
February 20, 2011
2100 Millennium Wood Stove (ACC)
Thimble
Site constructed for masonry chimney installation:
Components
• A minimum length of 12 inches [305mm] (longer for
thicker walls) of solid insulated factory-built chimney
length constructed to UL 103 Type HT 6 inch (152mm)
inside diameter. Chimney needs to extend a minimum
of 2 inches (51mm) from the interior wall and a minimum of 1 inch (25mm) from the exterior wall.
• Wall spacer, trim collar and wall band to fit solid pack
chimney selected.
• Minimum 8 inch (203mm) diameter clay liner section (if
not already present in chimney) and refractory mortar.
Air Clearances
• Masonry chimney clearance must meet NFPA 211 minimum requirement of 2 inches (51mm) to sheet metal
supports and combustibles.
• Minimum of 1 inch (25mm) clearance around the chimney connector.
• Top of wall opening is a minimum of 13-1/2 inches
(343mm) from ceiling or 4-1/2 inches (114mm) below
minimum clearance specified by chimney connector
manufacturer. NFPA 211 minimum vertical clearance of
18 inches (457mm) from chimney connector and ceiling or minimum recommended by chimney connector
manufacturer. Figure 15.1.
Figure 15.1
Solid Pack Chimney with Metal Supports as a Thimble
Instructions:
1. Open inside wall at proper height for the chimney connector to entry the masonry chimney. Figure 15.1
2. Entry hole to masonry chimney must be lined with an 8
inch (203mm) minimum diameter clay liner, or equivalent, secured with refractory mortar.
3. Construct a 17 inch x 17 inch (432mm x 432mm) outside dimension frame from 2 x 2 framing lumber to
fit into wall opening. Inside opening of frame should
be no less than 14 inch x 14 inch (356mm x 356mm).
Figure 15.1.
Fire Clay Flue
Liner
with Airspace
8. Insert a section of chimney connector into the chimney.
Make sure it does not protrude past the edge of the
clay chimney liner inside the chimney.
9. Seal the end of the chimney connector to the clay liner
with refractory mortar.
10. Install trim collar around the sold pack chimney section.
February 20, 2011
7039-131I
Wall Band to
Secure Chimney
Section
Chimney
Connector
5. Nail the frame into the wall opening. The spacer should
be on the chimney side.
7. Tightly secure the length of the solid insulated chimney
with the wall band to the masonry chimney.
Wall Spacer
Chimney Section
with 2 inch
(51mm)
Clearance to
Combustibles
4. Attach the wall spacer to the chimney side of the
frame.
6. Insert the section of the solid insulated chimney into
the outer wall of the masonry chimney.
Masonry
Chimney
Trim Collar
Wood Studs Used
for Framing - Spaced
2 inch (51mm)
clearance from
Masonry Chimney
Figure 15.2
WARNING
Fire Risk.
Do NOT pack insulation or other combustibles between
spacers.
• ALWAYS maintain specified clearances around venting and spacers.
• Install spacers as specified.
Failure to keep insulation or other material away from
vent pipe may cause fire.
Page 15
2100 Millennium Wood Stove (ACC)
Solid Pack Chimney with Metal Supports as a
Thimble (Cont’d)
Min. Chimney Clearance to
Wall Spacer and
Combustibles - 2 inch (51mm)
C. Installing Chimney Components
Chimney Connector
Single wall connector or stove pipe.
This must be at least 24 gauge mild steel or 26 gauge blue
steel. The sections must be attached to the appliance and to
each other with the crimped (male) end pointing toward the
stove. All joints, including the connection at the flue collar,
should be secured with 3 sheet metal screws. Make sure
to follow the minimum clearances to combustibles. Where
passage through the wall, or partition of combustible construction is desired in Canada, the installation shall conform
to CAN/CSA-B365.
Min. Clearance
2 inch (51mm)
1 inch (25mm) Air
Space to Chimney
Section
Chimney Flue
Liner
Fireclay
Liner or
Equivalent
Chimney
Connector
Chimney Section
Trim Collar
Masonry Chimney
Constructed to NFPA 211
Factory-built listed chimney connector (vented).
Wall Band
Wall Spacer
A listed connector (vented) must be used when installing this
unit in a mobile home. The listed connectors must conform
to each other to ensure a proper fit and seal.
Figure 16.1
Chimney Height / Rise and Run
This product was designed for and tested on a 6 inch (152mm)
chimney, 14 to 16 feet (420-480cm) high, (includes stove
height) measured from the base of the appliance. The further
your stack height or diameter varies from this configuration,
the possibility of performance problems exists.
Chimney height may need to be increased by 2 - 3% per
each 1000 feet above sea level. It is not recommended to
use offsets or elbows at altitudes above 4000 feet above sea
level or when there are other factors that affect flue draft.
Crimped
End
Toward
Stove
Flue Gas
Direction
Secure pipe sections with a
minimum of 3 screws
Figure 16.2 Chimney Connector (Stove Pipe)
WARNING
WARNING
Fire Risk.
Fire Risk.
Inspection of Chimney:
• Chimney must be in good condition.
• Meets minimum standard of NFPA 211
• Factory-built chimney must be 6 inch
(152mm) UL103 HT.
Follow Chimney Connector Manufacturer’s
Instructions for Proper Installation.
ONLY use connector:
• Within the room, between appliance and ceiling or wall.
Connector shall NOT pass through:
• Attic or roof space
• Closet or similar concealed space
• Floor or ceiling
Maintain minimum clearances to combustibles
WARNING
Asphyxiation Risk.
• DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVICING ANOTHER APPLIANCE.
• DO NOT CONNECT TO ANY AIR DISTRIBUTION DUCT OR SYSTEM.
May allow flue gases to enter the house.
Page 16
7039-131I
WARNING
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage. Refer
to the owner’s information manual provided with this appliance. For assistance or additional information consult a
qualified installer, service agency or your dealer.
February 20, 2011
2100 Millennium Wood Stove (ACC)
D. Chimney Termination Requirements
NOTE:
• Chimney performance may vary.
• Trees, buildings, roof lines and wind conditions affect
performance.
• Chimney height may need adjustment if smoking or
overdraft occurs.
Follow manufacturer’s instructions for clearance, securing
flashing and terminating the chimney.
• Must have an approved and listed cap
• Must not be located where it will become plugged by
snow or other material
• Must terminate at least 3 feet (91cm) above the roof
and at least 2 feet (61cm) above any portion of the
roof within 10 feet (305cm).
• Must be located away from trees or other structures
E. 2-10-3 Rule
These are safety requirements and are not meant to assure proper flue draft.
Less than 10 ft. (305cm)
2 ft. (61cm)
2 ft. (61cm)
10 ft. (305cm) To Nearest Roofline
3 ft. (91cm)
Minimum
3 ft. (91cm)
Minimum
Pitched Roof
Figure 17.1
10 ft. (305cm) or more
Less than 10 ft. (305cm)
Wall or Parapet
2 ft. (61cm) Minimum
3 ft. (91cm) Minimum
3 ft. (91cm) Minimum
Flat Roof
Figure 17.2
February 20, 2011
7039-131I
Page 17
2100 Millennium Wood Stove (ACC)
6
Mobile Home Installation
You must use a Quadra-Fire Outside Air Kit Part
OAK-ACC and (depending on floor installation, Part
SRV7033-041) for installation in a mobile home.
Snap Disc
1. An outside air inlet must be provided for combustion See
page 12 for installation information.
2. Appliance must be secured to the mobile home structure
by bolting the pedestal through hearth pad and into
floor.
3. Appliance must be grounded with #8 solid copper
grounding wire or equivalent and terminated at each end
with N.E.C. approved grounding device.
Magnet
4. Appliance must be installed with an approved UL103 HT
ventilated chimney connector, UL103 HT chimney, and
terminal cap with spark arrestor. Never use a single wall
connector (stove pipe) in a mobile home installation. Use
only double-wall connector pipe, Dura-Vent DVL, Selkirk
metalbestos DS or Security DL double-wall connector or
any listed double-wall connector pipe.
Spade
Connectors
5. In Canada, this appliance must be connected to a 6 inch
(152mm) factory-built chimney conforming to CAN/ULC629M, STANDARD FOR FACTORY BUILT CHIMNEYS.
6. Follow the chimney and chimney connector manufacturer’s
instructions when installing the flue system for use in a
mobile home.
7. Maintain clearance to combustibles.
8.Floor protection requirements must be followed
precisely.
9. Use silicone to create an effective vapor barrier at the
location where the chimney or other component penetrates
to the exterior of the structure.
NOTE: Offsets from the vertical, not exceeding 45°, are
allowed per Section 905(a) of the Uniform Mechanical Code
(UMC). Offsets greater than 45° are considered horizontal
and are also allowed, providing the horizontal run does not
exceed 75% of the vertical height of the vent. Construction,
clearance and termination must be in compliance with the
UMC Table 9C. This installation must also comply with NFPA
211.
NOTE: Top sections of chimney must be removable to allow
maximum clearance of 13.5 feet (411cm) from ground level
for transportation purposes.
Figure 18.1
CAUTION
THE STRUCTURAL INTEGRITY OF THE MOBILE HOME
FLOOR, WALL AND CEILING/ROOF MUST BE MAINTAINED
Do NOT cut through:
• Floor joist, wall, studs or ceiling trusses.
• Any supporting material that would affect the structural
integrity.
10. Burn wood only. Other types of fuels may generate
poisonous gases (e.g., carbon monoxide).
11. If unit burns poorly while an exhaust blower is on in
home, (i.e., range hood), increase combustion air.
12. Installation shall be in accordance with the Manufacturers
Home & Safety Standard (HUD) CFR 3280, Part 24.
Page 18
7039-131I
WARNING
Asphyxiation Risk.
NEVER INSTALL IN A SLEEPING ROOM.
Consumes oxygen in the room.
February 20, 2011
7
2100 Millennium Wood Stove (ACC)
Appliance Set-Up
B. Adjusting The Blower Speed Control
A. Door Handle Assembly
The blower speed control for this unit is adjusted at the factory,
and normally does not require further adjustment.
1. Install washer on door handle shaft.
2. Slide door handle through door.
NOTE: When the speed control is turned clockwise,
it will click on to high speed. Continue to turn the
speed control clockwise to decrease the speed. At
full clockwise, the blower should blow gently, but
should not stop.
3. Install second washer(s) as shown in Figure 19.1.
4. Install key in groove.
5. Align groove in latch cam with key; slide latch cam
over shaft
1. With the appliance plugged in, turn the speed
control knob to slow (full clockwise).
6. Install locknut but do not overtighten, the handle
needs to move smoothly.
7. Install spring handle turning in a counter-clockwise
motion to required 2 inch (51mm) clearance location on door handle rod. Figure 19.1.
CAUTION
2.
With a small screwdriver, adjust the blower speed
by turning the adjustment mechanism through the
hole on the side of the speed control.
3.
Adjust the speed so the blower runs slowly, but
does not stop. Turn clockwise to slow the blower
and counterclockwise to increase the speed.
• Do NOT overtighten lock nut.
• Door handle needs to move smoothly.
2 inch (51mm) clearance
required from bend in door
handle rod to end of spring
handle.
Latch Cam
Door Cross Section
(example)
Locknut
Spring
Handle
Spacing
Washers
Door Handle
Square Key
Figure 19.1
WARNING
HOT. Injury Risk.
• Maintain clearance between bend of
door handle rod and spring handle.
• Spring handle will get hot and may
cause injury.
February 20, 2011
7039-131I
Page 19
8
2100 Millennium Wood Stove (ACC)
Operating Instructions
A. Over-Firing Your Appliance
B. Wood Selection & Storage (Cont’d)
wood out - about one hour. It is a waste of energy to burn
unseasoned wood of any kind.
WARNING
Fire Risk
Do not over-fire.
Over-firing may ignite creosote or will damage
the stove and chimney.
To prevent over-firing your stove, DO NOT:
•
•
•
•
Use flammable liquids
Overload with wood
Burn trash or large amounts of scrap lumber
Permit too much air to the fire
1. Symptoms of Over-Firing
Symptoms of over-firing may include one or more of the
following:
• Chimney connector or appliance glowing
Splitting wood before it is stored reduces drying time. Wood
should be stacked so that both ends of each piece are
exposed to air, since more drying occurs through the cut ends
than the sides. This is true even with wood that has been
split. Store wood under cover, such as in a shed, or covered
with a tarp, plastic, tar paper, sheets of scrap plywood, etc.,
as uncovered wood can absorb water from rain or snow,
delaying the seasoning process.
C. Burning Process
• Roaring, rumbling noises
• Loud cracking or banging sounds
• Metal warping
• Chimney fire
2. What To Do if Your Stove is Over-Firing
• Immediately close the door and air controls to reduce
air supply to the fire.
• If you suspect a chimney fire, call the fire department
and evacuate your house.
• Contact your local chimney professional and have your
stove and stove pipe inspected for any damage.
• Do not use your stove until the chimney professional
informs you it is safe to do so.
Hearth & Home Technologies WILL NOT warranty stoves
that exhibit evidence of over-firing. Evidence of over-firing
includes, but is not limited to:
• Warped air tube
• Deteriorated refractory brick retainers
• Deteriorated baffle and other interior components
B. Wood Selection & Storage
Burn only dry seasoned wood. Store wood under cover, out
of the rain and snow. Dry and well-seasoned wood will not
only minimize the chance of creosote formation, but will give
you the most efficient fire. Even dry wood contains at least
15% moisture by weight, and should be burned hot enough
to keep the chimney hot for as long as it takes to dry the
Page 20
Dead wood lying on the forest floor should be considered wet,
and requires full seasoning time. Standing dead wood can
be considered to be about 2/3 seasoned. To tell if wood is
dry enough to burn, check the ends of the logs. If there are
cracks radiating in all directions from the center, it is dry. If
your wood sizzles in the fire, even though the surface is dry,
it may not be fully cured.
In recent years there has been an increasing concern about
air quality. Much of the blame for poor air quality has been
placed on the burning of wood for home heating. In order to
improve the situation, we at Quadra-Fire have developed
cleaner-burning woodstoves that surpass the requirements
for emissions established by our governing agencies. These
woodstoves, like any other appliances, must be properly
operated in order to insure that they perform the way they are
designed to perform. Improper operation can turn most any
wood stove into a smoldering environmental hazard.
1. Kindling or First Stage
It helps to know a little about the actual process of burning in
order to understand what goes on inside a stove. The first
stage of burning is called the kindling stage. In this stage, the
wood is heated to a temperature high enough to evaporate the
moisture which is present in all wood. The wood will reach
the boiling point of water (212°F) and will not get any hotter
until the water is evaporated. This process takes heat from
the coals and tends to cool the appliance.
Fire requires three things to burn - fuel, air and heat. So, if
heat is robbed from the appliance during the drying stage,
the new load of wood has reduced the chances for a good
clean burn. For this reason, it is always best to burn dry,
seasoned firewood. When the wood isn’t dry, you must
open the air controls and burn at a high burn setting for a
longer time to start it burning. The heat generated from the
fire should be warming your home and establishing the flue
draft, not evaporating the moisture out of wet, unseasoned
wood, resulting in wasted heat.
7039-131I
February 20, 2011
2100 Millennium Wood Stove (ACC)
2. Second Stage
The next stage of burning, the secondary stage, is the period
when the wood gives off flammable gases which burn above
the fuel with bright flames. During this stage of burning it is
very important that the flames be maintained and not allowed
to go out. This will ensure the cleanest possible fire. If the
flames tend to go out, it is set too low for your burning conditions. The air control located at the upper right hand corner
is used to adjust for burn rates. This is called the Burn Rate
Air Control. Figure 21.1.
3. Final Stage
The final stage of burning is the charcoal stage. This occurs
when the flammable gases have been mostly burned and only
charcoal remains. This is a naturally clean portion of the burn.
The coals burn with hot blue flames.
The second function of the Start-Up Air Control is operation
of the rear air system. The rear air is used primarily during
a High Burn Rate. However, in some instances rear air is
desired during normal operation to help with combustion of
fuel towards the back of the firebox particularly when burning
hardwoods. The rear air is controlled independently from the
ACC system. Slide the Start-Up Air Control between the first
and third marker as indicated on the label to allow rear air to
enter the firebox. Figure 21.1.
2. Manual Timer Over-Ride
If you need to shut the ACC system off before it shuts itself
off after 25 minutes (i.e. overfire situation), reach down to
the bottom right rear corner and pull the lever toward you.
Figure 21.2.
It is very important to reload your appliance while enough
lively hot coals remain in order to provide the amount of heat
needed to dry and rekindle the next load of wood. It is best
to open the Burn Rate Air and Start-Up Air Controls before
reloading. This livens up the coalbed and reduces excessive
emissions (opacity/smoke). Open door slowly so that ash or
smoke does not exit appliance through opening. You should
also break up any large chunks and distribute the coals so
that the new wood is laid on hot coals.
HIGH
Burn Rate
Air Control
MED
LOW
Air quality is important to all of us, and if we choose to use
wood to heat our homes we should do so responsibly. To do
this we need to learn to burn our stoves in the cleanest way
possible. Doing this will allow us to continue using our wood
stoves for many years to come.
D. Automatic Combustion Control (ACC)
Typically, when you build a fire, you open the air controls fully
and monitor the fire to prevent it from going into an overfire
situation and/or burning your wood up too quickly before you
shut down the air controls to the desired burn rate. With the
Automatic Combustion Control (ACC) system, you do not
have to continually monitor the fire. Once you set the ACC
system it will control the fire for you. Follow the instructions
below to learn how to operate your stove with ease.
Start-Up
Air Control
Figure 21.1
E. Air Controls
1. Start-Up Air Control
The Start-Up Air Control has two primary functions. The
first function is to activate the Automatic Combustion Control
system (ACC). This function is performed by sliding the control all the way back until it stops at the “HI” indicator on the
label and then pulling forward to the front of the stove until
it stops. This activates the ACC system and opens the front
air channel and allows air to enter the front of the stove for
approximately 25 minutes. The front air channel gradually
shuts down until it is completely closed at the end of the 25
minutes. The fire is now controlled by the air supplied by the
Burn Rate Air Control. This function should be performed
each time you reload the stove. Figure 21.1.
February 20, 2011
7039-131I
Pull Forward
to Shut Down
Manual
Timer (ACC)
Shut Down
Figure 21.2
Page 21
2100 Millennium Wood Stove (ACC)
2. Burn Rate Air Control
4. Medium-Low Burn Rate - 10,000 to 15,000 BTU/hr
This air supply enters at the upper front of the firebox, near the
top of the glass door. This preheated air supplies the necessary fresh oxygen to mix with the unburned gases, helping
to create second, third and fourth combustions. This air is
regulated by the Burn Rate Air Control. There are four settings
High, Medium-High, Medium-Low and Low. When the control
is raised all the way up it is on the High setting and when
pushed all the down it is on the Low setting. Figure 22.1.
Raise the Burn Rate Air Control up to the bottom of
the middle marker and stop. Slide the Start-Up Air
Control all the way back until it stops (HI marker) and
then pull forward until it stops. This activates the timer
system (ACC).
5. Low Burn Rate - Below 10,000 BTU/hr
Leave the Burn Rate Air Control at the bottom marker.
Slide the Start-Up Air Control all the way back until it
stops (HI marker) and then pull forward until it stops.
This activates the timer system (ACC).
F. Burn Rates and Operating Efficiency
For maximum operating efficiency
HIGH
1. This appliance has a timer system (ACC) that operates
the stove at its maximum efficiency removing any guess
work for the homeowner. Follow the instructions below
for each burn rate for the Start-Up Air Control and Burn
Rate Air Control. Figure 22.1.
Shown with Side
Shield Removed
LOW
2. Burn dry, well-seasoned wood.
Low (Closed)
Burn Rates
1. Starting a Fire and Reloading
High (Open)
Open both controls fully by raising the Burn Rate Air
Control all the way up until it stops and slide the Start-up
Air Control back until it stops. After loading the stove with
wood and starting the fire, set both controls to the desired
setting by following the burn rate instructions below.
Burn Rate
Air Control
Front Air Channel
Operated by Timer
NOTE: These are approximate settings, and will vary with
type of wood or chimney draft. Due to altitude and other
environmental circumstances, this operational information is
a guideline only. Start-Up Air
Control
2. High Burn Rate - Maximum Heat
Raise the Burn Rate Air Control all the way up until it stops
(top marker) to a fully open position. Slide the Start-Up Air
Control all the way back until it stops (HI marker) and leave
it there. This setting over-rides the timer system (ACC) so
you must monitor the fire closely while in this setting.
Timer
Rear Air Channel
Operates independently
from Timer
Timer Manual
Shut-off
START-UP
REAR AIR
WARNING
HI
Risk of Fire.
When set on High Burn Rate and over-riding
the Automatic Combustion Control system an
overfire situation can occur and may result in a
chimney fire.
Overfiring will void the stove warranty.
3. Medium-High Burn Rate - 15,000 to 30,000 BTU/hr
Raise the Burn Rate Air Control all the way up until it
stops (top marker) to a fully open position. Slide the
Start-Up Air Control all the way back until it stops (HI
marker) and then pull forward until it stops. This activates
the timer system (ACC).
Page 22
Closed
Wide
Open
“HI” setting
over-rides
Timer
After activating the timer (ACC), if the control is placed
within the rear air section on the label it will allow rear air
to enter the firebox. This will not interfere with the timer
gradually closing the front air channel in 25 minutes. If
control is set on “HI” it over-rides the timer (ACC).
Figure 22.1
NOTE: Operate appliance on High Burn 15 minutes a
day to help keep flue/chimney clean.
7039-131I
February 20, 2011
2100 Millennium Wood Stove (ACC)
G. Building A Fire
Baffle Board even with front
tube & resting on all tubes
Before lighting your first fire in the stove:
1. Confirm the baffle is correctly positioned. It should be
even with the front tube and resting on all tubes. Figure
23.1.
Burn Rate
Air Control
2. Remove all labels from glass.
There are many ways to build a fire. The basic principle
is to light easily-ignitable tinder or paper, which ignites the
fast burning kindling, which in turn ignites the slow-burning
firewood. Here is one method that works well:
Start-Up
Air
Control
1. Open the Burn Rate Air and Start-Up Air Controls fully.
2. Place several wads of crushed paper on the firebox floor.
Heating the flue with slightly crumpled newspaper before
adding kindling keeps smoke to a minimum.
Ceramic Blanket on Top
3. Lay small dry sticks of kindling on top of the paper.
4. Make sure that no matches or other combustibles are in
the immediate area of the appliance. Be sure the room
is adequately ventilated and the flue unobstructed.
5. Light the paper in the appliance. NEVER light or rekindle
fire with kerosene, gasoline, or charcoal lighter fluid; the
results can be fatal.
6. Once the kindling is burning quickly, add several fulllength logs 3 inches (76mm) or 4 inches (102mm) in
diameter. Be careful not to smother the fire. Stack the
pieces of wood carefully; near enough to keep each
other hot, but far enough away from each other to allow
adequate air flow between them.
Tube Channel
Figure 23.1
7. Set the Burn Rate Air Control and activate the timer
system (ACC).
8. When ready to reload, It is best to fully open both the
Burn Rate Air and Start-up Air Controls before reloading. This livens up the coalbed and reduces excessive
emissions (opacity/smoke). Open door slowly so that
ash or smoke does not exit appliance through opening.
Large logs burn slowly, holding a fire longer. Small logs
burn fast and hot, giving quick heat.
9. As long as there are hot coals, repeating steps 6
through 8 will maintain a continuous fire throughout the
season.
2 pc Baffle Board
WARNING
Fire Risk.
Do NOT store wood:
• Closer than required clearances to combustibles to appliance
• Within space required for loading or ash
removal.
Do NOT operate appliance:
• With appliance door open.
• With ash removal system door open.
WARNING
Fire Risk.
NOTE:
• Build fire on brick firebox floor.
• Do NOT use grates, andirons or other methods to support
fuel.
It will adversely affect emissions.
February 20, 2011
7039-131I
• Do NOT burn wet or green wood.
• Store wood in dry location.
• Stack wood so both ends are exposed to air.
Wet, unseasoned wood can cause accumulation of
creosote.
Page 23
2100 Millennium Wood Stove (ACC)
H. Correct Baffle & Blanket Placement
INCORRECT POSITIONS
WARNING
Fire Risk
Firebox damage due to improper baffle placement is not covered by warranty. Operate the
wood burning appliance with the baffle in the
correct position only.
Not doing so could result in:
• Reduced efficiency
• Overheating the chimney
• Overheating the rear of the firebox
Ceramic Blanket and Baffle Board are NOT
in contact with the back of the firebox.
• Poor performance
Ensure correct baffle placement and replace baffle components if damaged or missing.
CORRECT POSITION
Baffle Retainer Bracket
Ceramic Blanket
Back of Firebox
Ceramic Blanket is NOT in contact with the
back of the firebox and NOT even with the
Baffle Board in the front.
Baffle Board
Ceramic Blanket
Back of Firebox
Ceramic Blanket and Baffle Board MUST be
in contact with the back of the firebox and
even with each other in the front.
Baffle Board
Ceramic Blanket is bunched up at the back
of the firebox and NOT even with the Baffle
Board in the front.
Figure 24.1
Page 24
Figure 24.2
7039-131I
February 20, 2011
2100 Millennium Wood Stove (ACC)
I. Blower Operating Instructions
J. Opacity (Smoke)
NOTE: If your Quadra-Fire wood stove is equipped with an
optional blower, you should follow these guidelines:
This is the measure of how cleanly your appliance is burning. Opacity is measured in percent; 100% opacity is when
an object is totally obscured by the smoke column from a
chimney, and 0% opacity means that no smoke column can
be seen. As you become familiar with your appliance, you
should periodically check the opacity. This will allow you to
know how to burn as nearly smoke-free as possible (goal of
0% opacity).
1.
Initial (cold) start-up and all Burn Settings
The blower can be plugged in and turned on right away.
The blower fan is turned on and off by a snap disc.
When your stove has reached a certain temperature
the blower will turn on and when your stove has cooled
down to a certain temperature it will turn off.
NOTE: The blower can still be left on at all burn rates
even if you have deactivated the snap disc with the
manual over-ride knob. See page 13.
2.
3.
The blower is equipped with a speed control. Adjust
the fan speed by turning the speed control clockwise
to “Low” or counterclockwise to “High”.
Snap Disc Location
If you find the blower coming on and off at undesirable
temperatures, relocate the snap disc to another location
in the designated zone on the back of the appliance.
Figure 25.1. There is a manual over-ride switch to
deactivate the snap disc, if necessary. See page 13.
WARNING
Fire Risk.
• DO NOT BURN GARBAGE OR FLAMMABLE
FLUIDS SUCH AS GASOLINE, NAPTHA OR
ENGINE OIl.
• Do NOT burn treated wood or wood with salt (driftwood).
• May generate carbon monoxide if burn material other
than wood.
May result in illness or possible death.
WARNING
Fire Risk.
Keep combustible materials, gasoline
and other flammable vapors and liquids
clear of appliance.
• Do NOT store flammable materials in the appliance’s
vicinity.
• DO NOT USE GASOLINE, LANTERN FUEL,
KEROSENE, CHARCOAL LIGHTER FLUID OR
SIMILAR LIQUIDS TO START OR “FRESHEN UP” A
FIRE IN THIS HEATER.
• Keep all such liquids well away from the heater while it
is in use.
• Combustible materials may ignite.
Figure 25.1
February 20, 2011
7039-131I
Page 25
2100 Millennium Wood Stove (ACC)
K. Frequently Asked Questions
ISSUES
SOLUTIONS
Odor from appliance
When first operated, this appliance may release an odor for the first several hours. This is caused by
the curing of the paint and the burning off of any oils remaining from manufacturing.
Metallic noise
Noise is caused by metal expanding and contracting as it heats up and cools down, similar to the
sound produced by a furnace or heating duct. This noise does not affect the operation or longevity of
the appliance.
Whirring sound
If the optional blower has been installed, the blower produces a whirring sound which increases in
volume as the speed is increased.
CAUTION
Odors and vapors released during initial operation.
• Curing of high temperature paint.
• Open windows for air circulation.
Odors may be irritating to sensitive individuals.
Page 26
7039-131I
February 20, 2011
9
2100 Millennium Wood Stove (ACC)
Maintaining & Servicing Your Appliance
A. Quick Reference Maintenance Guide
BAFFLE & BLANKET PLACEMENT
Baffle Retainer Bracket
Ceramic Blanket
INSPECT FIREBRICKS & ASH GRATE
(AFTER EACH CLEANING)
Back of Firebox
2
Baffle Board
2
Step Top Models Only
Baffle and blanket placement is critical to heat output, efficiency and overall life of the unit. Make sure
the baffle is pushed all of the way to the back of the
firebox and the blanket is laying flat.
Firebrick is designed to protect your firebox. Replace
firebricks that are crumbling, cracked or broken. If
you have an optional ash door, check to make sure
the door is closing properly.
CHIMNEY & CAP INSPECTION
DOOR & LATCH CHECK
Keeping the door and glass
gasket in good shape will
maintain good burn times on
a low burn setting.
The chimney and chimney
cap must be inspected for
soot and creosote during
the burn season. This will
prevent pipe blockage, poor
draft, and chimney fires.
Check the glass frame for
loose screws to prevent air
leakage.
Latch Cam
Always burn dry wood to
help prevent cap blockage
and creosote build-up.
Door Cross Section
(example)
Locknut
Spring
Handle
Door Handle
Spacing
Washers
Square Key
Check the door latch for proper adjustment. This
is very important especially after the door rope has
formed to the stove face.
Start the first inspection of your unit after the first 2 months of use, or if performance changes, and adjust your schedule accordingly.
February 20, 2011
Maintenance is required for safe operation and must be performed to maintain your warranty.
7039-131I
Page 27
2100 Millennium Wood Stove (ACC)
B. General Maintenance
2. Disposal of Ashes
1. Creosote (Chimney) Cleaning
•
•
Frequency: Every 2 months during heating season or
as recommended by a certified chimney
sweep; more frequently if chimney exceeds
or is under 14-16 ft. (measured from bottom
of appliance)
By: Certified Chimney Sweep
• Frequency: When ash is within 1-3/4 in. (44mm) of
firebox lip
• By: Homeowner
Ashes should be placed in a metal container with a
tight fitting lid. The closed container of ashes should
be placed on a non-combustible floor or on the ground,
well away from all combustible materials, pending final
disposal. If the ashes are disposed of by burial in soil
or otherwise locally dispersed, they should be retained
in the closed container until all cinders have thoroughly
cooled.
Remove all ash from the firebox and extinguish all hot embers
before disposal. Allow the appliance to cool completely.
Disconnect flue pipe or remove baffle and ceramic blanket
from appliance before cleaning chimney. Otherwise residue
can pile up on top of the baffle and ceramic blanket and
the appliance will not work properly. (See Baffle Removal
on page 31). Close the door tightly. The creosote or soot
should be removed with a brush specifically designed for
the type of chimney in use. Clean out fallen ashes from the
firebox.
WARNING
Fire Risk.
Disposal of Ashes
• Ashes should be placed in metal container with
tight fitting lid.
• Do not place metal container on combustible
surface.
• Ashes should be retained in closed container until
all cinders have thoroughly cooled.
It is also recommended that before each heating season
the entire system be professionally inspected, cleaned and
repaired if necessary.
Inspection: Inspect the system at the appliance connection
and at the chimney top. Cooler surfaces tend to build creosote
deposits quicker, so it is important to check the chimney from
the top as well as from the bottom.
Formation and Need For Removal: When wood is burned
slowly, it produces tar and other organic vapors which
combine with expelled moisture to form creosote.
The creosote vapors condense in the relatively cool chimney
flue of a newly-started or a slow-burning fire. As a result,
creosote residue accumulates on the flue lining. When
ignited, this creosote creates an extremely hot fire which may
damage the chimney or even destroy the house.
The chimney connector and chimney should be inspected
once every 2 months during the heating season to determine
if a creosote or soot buildup has occurred. If creosote or soot
has accumulated, it should be removed to reduce the risk of
a chimney fire.
WARNING
Fire Risk.
Prevent creosote buildup.
• Inspect chimney connector and chimney once
every two months during heating season.
• Remove creosote to reduce risk of chimney fire.
3. Glass Cleaning
• Frequency: As desired
• By: Homeowner
Clean glass with a non-abrasive glass cleaner. Abrasive
cleaners may scratch and cause glass to crack. If the
deposits on the glass are not very heavy, normal glass
cleaners work well. Heavier deposits may be removed by
using a damp cloth dipped in wood ashes or by using a
commercially available oven cleaner.
After using an oven cleaner, it is advisable to remove any
residue with a glass cleaner or soap and water. Oven cleaner
left on during the next firing can permanently stain the glass
and damage the finish on plated metal surfaces.
A portion of the combustion air entering the firebox is deflected
down over the inside of the door glass. This air flow “washes”
the glass, helping to keep smoke from adhering to its surface.
When operated at a low burn rate, less air will be flowing over
the glass and the smokey, relatively cool condition of a low
fire will cause the glass to become coated.
Operating the appliance with the Burn Rate Air Control and
Start-Up Air Control all the way open for 15-20 minutes should
remove the built up coating.
• Ignited creosote is extremely HOT.
WARNING
Fire Risk.
• Do not use chimney cleaners or flame colorants in your appliance.
Will corrode pipe.
Page 28
7039-131I
February 20, 2011
2100 Millennium Wood Stove (ACC)
CAUTION
WARNING
Handle glass with care.
Handle glass assembly with care.
Glass
Assembly
•
•
•
•
When cleaning glass:
• Avoid striking, scratching or
slamming glass.
• Do NOT clean glass when hot.
Glass
Assembly
Do NOT use abrasive cleaners.
Use a hard water deposit glass cleaner on white film.
Use commerical oven cleaner on heavier deposits.
Remove all residue of oven cleaner or will permanently
stain glass on next firing.
• Inspect the gasket to ensure it is
undamaged.
• Do NOT strike, slam or scratch glass.
• Do NOT operate appliance with glass
& door assembly removed.
• Do NOT operate with glass cracked, broken or scratched.
•
Refer to maintenance instructions.
WARNING
Fire Risk.
Injury Risk.
C. Glass Replacement
• Use only glass specified in manual.
1. Ensure that the fire is out and the appliance is cool to
the touch.
• DO NOT REPLACE with any other material.
Glass breakage will occur.
2. Protect a table or counter top with padding or towels.
Protect your hands and wear gloves to prevent injury.
3. Remove the door with the broken glass by lifting the
door up and off of the hinges.
4. Lay door face down on a table or counter making sure
the handle hangs over the edge so the door lays flat, on
a soft surface.
5. Remove the screws from each glass retainer and remove
the glass. (If screws are difficult to remove, soak with
penetrating oil first).
6. Center the glass with edges evenly overlapping the
opening in the door, (i.e. same space top and bottom,
left and right sides).
7. Replace the glass retainers. Be careful not to cross
thread the screws.
8. Tighten each retainer just a few turns until each is
secured. Check again for centering of glass in door
frame. Continue to tighten each retainer alternately, a
few turns at a time, until the glass is secure. DO NOT
OVERTIGHTEN.
9. Replace the door on the appliance.
Quadra-Fire stoves are equipped with ceramic super heatresistant glass, which can only be broken by impact or
misuse. Do not slam stove door or impact the glass. When
closing door, make sure that logs do not protrude against the
glass. Inspect glass regularly. If you find a crack or break,
immediately put the fire out and return the door to your dealer
for replacement of glass before further use.
February 20, 2011
7039-131I
Page 29
2100 Millennium Wood Stove (ACC)
D. Firebrick Replacement
Replace the firebrick if they become crumbly and/or if
there is a 1/4 inch (6.35mm) gap between the bricks.
3
3
Inspect the firebrick after each ash removal.
1
1
The firebox is lined with high quality firebrick, which has
exceptional insulating properties. There is no need to
use a grate; simply build a fire on the firebox floor. Do
not operate appliance without firebrick.
1
1. After the coals have completely cooled, remove all
old brick and ash from unit and vacuum firebox.
1
1
1
1
1
5
2. Remove new brick set from box and lay out to
diagram shown.
1
2
2
2
4
3. Lay bottom bricks in unit.
4. Install rear bricks on the top of the bottom bricks.
Slide top of bricks under clip on back of firebox wall
and push bottom of brick back.
8-1/2 inches (216mm)
5. Install side bricks. Slide top of brick under clips
on side of firebox and push the bottom of the brick
until it is flush with the side of the unit.
1-3/8 in.
(35mm)
4
1-3/4 in.
(44mm)
Use Part 832-0550 when ordering individual brick. Provide brick
dimension or copy this page, mark the desired brick and take it
to your authorized dealer.
6-1/4 inches
(159mm)
7 inches (178mm)
5
3 inches
(76mm)
8-1/2 inches (216mm)
Figure 30.1
No.
Page 30
Brick Size
Qty
1
9 x 4-1/2 x 1-1/4
9
2
6 x 4-1/2
3
3
8 x 4-1/2 x 1-1/4
2
4
Brick with angle (see drawing)
1
5
Brick with angle (see drawing)
1
7039-131I
February 20, 2011
2100 Millennium Wood Stove (ACC)
F. Snap Disc Replacement
E. Baffle Removal
1. Remove all ash from the firebox, and extinguish all hot
embers before disposal into a metal container.
1. Locate the snap disc bracket assembly at the bottom left
rear corner of the stove. Figure 31. 3.
2. The baffle board has 2 pieces. With the ceramic blanket 2. A magnet holds the bracket to the stove. Pull the bracket
down away from the stove to expose the snap disc.
still in place, slide one baffle piece over the top of other one
and pull out top piece through the door opening and then 3. Pull the snap disc and spade connectors up and out of
remove bottom baffle piece. Figure 31.1.
bracket as shown in Figure 31.4.
3. Remove the ceramic blanket.
4. Using a Phillips head screw driver, remove the 2 screws
from the snap disc and then remove the snap disc from
4. Re-install the baffle pieces one piece at a time. Be sure
the spade connectors. Replace with new snap disc and
the baffle boards are even with the front manifold tube and
re-connect to spade connectors.
is resting on all tubes. Figure 23.1 on page 23. See Also
Correct Blanket & Baffle Position on page 24.
5. Push the snap disc and spade connectors back inside
bracket and re-attach the bracket to the stove.
5. To re-install the ceramic blanket, it is easier to fold it in half
first. Figure 31.2. Place on top of baffle board, open up
and flatten and smooth out the blanket. Re-check the baffle
board for correct positioning. Figure 23.1 on page 23 and
page 24.
Figure 31.1 - Baffle
Snap Disc Location
Figure 31.3
Snap Disc
Magnet
Spade
Connectors
Figure 31.2 - Ceramic Blanket
Figure 31.4
February 20, 2011
7039-131I
Page 31
2100 Millennium Wood Stove (ACC)
G. Tube Channel Assembly Replacement
NOTE: Service Space
Removing Tube Channel Assembly
1. Remove the right side shield by removing 2 screws in the
back using a Phillips head screw driver.
2. Remove 4 screws from channel access cover and remove
cover.
3.Locate 2 channel nuts inside of chamber and remove
using a 7/16 socket wrench. Slide out tube channel
assembly.
In order to replace the tube channel assembly a clearance of 17 inches (432mm) is required on the right side
of stove in order to remove the tubes with the stove in
place.
If space is not available, the stove will have to be disconnected from the chimney to proceed with the tube
replacement.
NOTE:Soak the bolts with penetrating oil for at least 15 minutes before trying to remove them.
Replacing Tube Channel Assembly
1.Slide one gasket on each tube first
2.Slide the tube channel assembly into side of firebox and
insert each tube into the corresponding hole in the tube
channel rack starting with the back hole first.
3.Make sure tube channel assembly is flush against the
side of the stove and secure with channel nuts.
4. Re-install channel cover and side shield.
Tube Channel Rack
Slide one gasket
over each tube
Channel
Access
Cover
Channel Cover
Screws (4)
Channel
Nuts (2)
Remove
2 Screws
Tube Channel
Assembly
Side Panel
Figure 32.1
Page 32
7039-131I
February 20, 2011
10
2100 Millennium Wood Stove (ACC)
Troubleshooting
Start Fire Problems
Can’t get fire started
Excessive smoke or spillage
Burns too slowly
Smolders, sizzles
With proper installation, operation, and maintenance your woodstove
will provide years of trouble-free service. If you do experience a problem, this troubleshooting guide will assist a qualified service person in
the diagnosis of a problem and the corrective action to be taken.
Possible Cause
Solution
Not enough kindling/paper or no
kindling/paper
Use dry kindling, more paper. Arrange kindling & wood
for air movement.
Not enough air for fire to ignite
Check for restricted cap/shroud
Open outside air kit (if installed).
Check for flue blockage.
Pre-warm flue before starting fire (refer to starting fire
section).
Check for adequate vent height (refer to chimney
assembly section).
Open window below the appliance towards the wind.
Wood condition is too wet, too large
Use dry, seasoned wood (refer to wood fuel section).
Bed of coals not established before
adding wood
Start with paper & kindling to establish bed of coals (refer
to starting fire section).
Flue blockage such as birds’ nests or
leaves in termination cap
Have chimney inspected for creosote and cleaned by a
certified chimney sweep.
Down draft or negative pressure
Competition with exhaust devices
Do not use exhaust fans during start-up (refer to negative
pressure section).
Open window below the appliance towards the wind.
Fire burns too fast
Extremely dry or soft wood
Mix in hardwood.
Mix in less seasoned wood after fire is established (refer
to wood fuel section).
Overdrafting
Check for correct vent height; too much vertical height
creates overdrafting.
Check location of vent termination (refer to chimney
requirements section).
February 20, 2011
7039-131I
Page 33
2100 Millennium Wood Stove (ACC)
11
21M-ACC
Reference Materials
Service Parts
R
Beginning Manufacturing Date: July 2007
2100 Millennium Wood Stove
Ending Manufacturing Date: Active
Advanced Combustion Control (ACC)
A. Exploded Drawings
3
2
1
4
16
15
5
6
12
7
13
8
9
14
10
11
Part number list on following pages.
04/11
Figure 34.1
Page 34
7039-131I
February 20, 2011
2100 Millennium Wood Stove (ACC)
R
21M-ACC
Service Parts
Beginning Manufacturing Date: July 2007
Ending Manufacturing Date: Active
B. Service Parts & Accessories
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement
parts for your appliance please provide model number and serial number. All parts listed
in this manual may be ordered from an authorized dealer.
ITEM
DESCRIPTION
COMMENTS
Stocked
at Depot
PART NUMBER
1
Convection Air Channel - Retain Originial Serial Number
2
Flue Collar
SRV7000-302
3
Panel Assembly, Side, Left
SRV7039-003
#4 Brick Assembly
SRV7039-107
4.3
4.3
4.1
4.1
4.1
4.1
4.1
4.1
4.1
4.1
4.1
4.2
4.5
4.2
4.2
8-1/2”
4.4
6-1/4”
4
Y
4.4
7”
1-3/8”
1-3/4”
4.5
3”
8-1/2”
Brick Assembly - Complete Set
SRV7039-007
4.1
Brick, 9 x 4-1/2 x 1-1/4”
Qty. 9 Req.
4.2
Brick, 6 x 4-1/2 x 1-1/4”
Qty. 3 Req.
4.3
Brick, 8 x 4-1/2 x 1-1/4”
Qty. 2 Req.
4.4
Brick, see diagram
Qty. 1 Req.
4.5
Brick, see diagram
Qty. 1 Req.
Brick, Uncut
Pkg of 1
832-0550
Pkg of 6
832-3040
5
Tube Support Rack
SRV7039-108
6
Brick Retainer
7033-149
7
Ceramic Fiber Blanket, 1/2” Thick
832-3390
Y
SRV7039-111
Y
8
Baffle Board, 8-1/8 in. W x 13 in. H
9
Pedestal Riser
Pkg of 2
7033-207
10
Pedestal Base
7033-163
11
Strip, Oak Trim
12
Rear Channel Assembly
Pkg of 2
SRV7039-001
832-0560
13
Tube Channel Assembly - Manifold Tubes
SRV7039-004
14
Panel Assembly, Side, Right
SRV7039-002
15
Tube Channel Top - Access Cover
SRV7039-114
Component Pack (Includes Touch-Up Paint, Gold Spring
Handles 1/2 In & 1/4 In (1) Each, Trimount Plug, Owners
Manual, Warranty Card)
7039-011
Y
Additional service part numbers appear on following page.
February 20, 2011
7039-131I
04/11
Page
35
2100 Millennium Wood Stove (ACC)
R
21M-ACC
Service Parts
Beginning Manufacturing Date: July 2007
Ending Manufacturing Date: Active
# 16 Burn Rate Control Assembly
#18 Baffle Protection Channel
#17 Door Assembly
Side view
16.10
16.1
16.9
16.2
Front, looking into unit
17.1
17.2
16.8
16.3
17.7
16.7
16.4
16.5
Ceramic blanket
17.8
Fiber baffle
17.9
17.6
16.6
17.3
17.5
17.4
Baffle
protection
channel sits in
between front
tube and fiber
This tab sits behind the front tube.
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement
parts for your appliance please provide model number and serial number. All parts listed
in this manual may be ordered from an authorized dealer.
ITEM
16.1
DESCRIPTION
COMMENTS
Burn Rate Control Assembly
PART NUMBER
7039-016
Spring Handle, 1/4” Nickel
16.2
Stocked
at Depot
Pre SN 0070040260
Spring Handle, 1/4” Gold
Spring Handle, 1/4” Black
Post SN 0070040260
250-8340
Y
832-0630
Y
SRV7000-614
Y
Timer Air Control Assembly
SRV7039-015
Y
Rear Air Door Assembly
7037-013
Y
16.4
Rear Air Control Arm Assembly
SRV7039-006
16.5
Start-Up Control Knob
7000-343
16.6
Latch, Magnet - for Air Control
229-0631
16.7
Air Control Rod Guide
7033-210
16.8
Timer (Only) Replacement Assembly
SRV480-1940
Y
16.9
Timer Arm Assembly
7033-034
Y
16.10
Door Gasket - Front & Rear Air Timer Doors
7033-282
Y
17.1
Door Assembly
16.3
17.2
Hinge Pins, 1/2”
Spring Handle, 1/2”, Nickel
17.3
Black
SRV7039-008
Gold
832-0250
Nickel
430-5320
Black
7000-606/2
Pre SN 0070040260
Spring Handle, 1/2”, Gold
Spring Handle, 1/2”, Black
Post SN 0070040260
250-8330
Y
832-0620
Y
SRV7000-613
Y
17.4
Door Handle Only
430-1131
17.5
Glass Assembly - 14-1/8 in. W x 9-13/16 in. H
7000-013
17.6
Key, Cam Latch
430-1151
17.7
Cam Latch
430-1141
Y
17.8
Nut, Locking Door Handle
17.9
Frame, Glass, Top
GL-FRM-21M
Baffle Protection Channel
SRV7039-144
18
Pkg of 24
Y
226-0100/24
Y
Additional service part numbers appear on following page.
Page 36
7039-131I
February 20, 04/11
2011
2100 Millennium Wood Stove (ACC)
R
21M-ACC
Service Parts
Beginning Manufacturing Date: July 2007
Ending Manufacturing Date: Active
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement
parts for your appliance please provide model number and serial number. All parts listed
in this manual may be ordered from an authorized dealer.
ITEM
DESCRIPTION
COMMENTS
Component Pack (Includes Gold Spring Handles (1) 1/2"
& (2) 1/4", (2) Gold Hinge Pins, Quadra-Fire Logo
For Black & Gold
Doors
Stocked
at Depot
PART NUMBER
436-5350
Gasket, Glass Tape
5 FT
832-0460
Y
Rope, Door, 3/4” X 84”
7 Ft
832-1680
Y
Paint Touch-Up
812-0910
Plug, Trimount, .250”
Pkg of 24
Door Handle Assembly
Logo, Quadra-Fire
229-0880/24
Y
832-0540
Y
Gold
200-3180
Nickel
200-3240
Outside Air Cover Plate Assembly
SRV7033-041
Y
ACCESSORIES
Blower Assembly
BK-ACC
Blower Control Box W/Switch
SRV7000-194
Y
Blower, Convection
812-4900
Y
Component Pack
7033-051
Snap Disc Bracket Assembly
7033-036
Snap Disc, # 1, Convection Blower
SRV230-0470
Wire Harness (Blower)
7033-262
Gasket, Manifold
Pkg of 4
Outside Air Kit, Floor & Rear
7038-168/4
Y
Y
OAK-ACC
Outside Air Collar Assembly
7033-039
Outside Air Shield
33271
Upgrade, Door, Nickel - Handles, Hinge Pins & Logo
Y
UK-DRNL
Hinge Pins, 1/2”
430-5320
Logo, Quadra-Fire
200-3240
Spring Handle, 1/2”
250-8330
Y
Spring Handle, 1/4”
250-8340
Y
RIVNUT-REPAIR
Y
FASTENERS
Avk Rivnut Repair Kit - 1/4-20 & 3/8-16 Rivnut Tools
Bolt, Hex Head, 1/4-20 X 1
Pkg of 10
25221A/10
Y
Nut, Ser Flange Small 1/4-20
Pkg of 24
226-0130/24
Y
Screw, Flat Head Philips 8-32 X 1/2
Pkg of 10
832-0860
Y
Screw, Sheet Metal #8 X 1/2 S-Grip
Pkg of 40
12460/40
Y
Washer, 1/4 Sae
Pkg of 24
28758/24
Y
Washer, Sae, 3/8
Pkg of 3
832-0990
Y
February 20, 2011
7039-131I
04/11
Page 37
2100 Millennium Wood Stove (ACC)
C. Service And Maintenance Log
Date of Service
Page 38
Performed By
Description of Service
7039-131I
February 20, 2011
2100 Millennium Wood Stove (ACC)
C. Service And Maintenance Log (Cont’d)
Date of Service
February 20, 2011
Performed By
Description of Service
7039-131I
Page 39
2100 Millennium Wood Stove (ACC)
D. Homeowner’s Notes
Page 40
7039-131I
February 20, 2011
2100 Millennium Wood Stove (ACC)
D. Homeowner’s Notes (Cont’d)
February 20, 2011
7039-131I
Page 41
2100 Millennium Wood Stove (ACC)
E. Castile
Warranty
Policy
Pellet
Insert
R
Hearth & Home Technologies Inc.
LIMITED LIFETIME WARRANTY
Hearth & Home Technologies Inc., on behalf of its hearth brands (”HHT”), extends the following warranty for
HHT gas, wood, pellet, coal and electric hearth appliances that are purchased from an HHT authorized dealer.
WARRANTY COVERAGE:
HHT warrants to the original owner of the HHT appliance at the site of installation, and to any transferee taking ownership
of the appliance at the site of installation within two years following the date of original purchase, that the HHT appliance
will be free from defects in materials and workmanship at the time of manufacture. After installation, if covered components manufactured by HHT are found to be defective in materials or workmanship during the applicable warranty period,
HHT will, at its option, repair or replace the covered components. HHT, at its own discretion, may fully discharge all of its
obligations under such warranties by replacing the product itself or refunding the verified purchase price of the product
itself. The maximum amount recoverable under this warranty is limited to the purchase price of the product. This warranty
is subject to conditions, exclusions and limitations as described below.
WARRANTY PERIOD:
Warranty coverage begins on the date of original purchase. In the case of new home construction, warranty coverage
begins on the date of first occupancy of the dwelling or six months after the sale of the product by an independent,
authorized HHT dealer/ distributor, whichever occurs earlier. The warranty shall commence no later than 24 months
following the date of product shipment from HHT, regardless of the installation or occupancy date. The warranty period for
parts and labor for covered components is produced in the following table.
The term “Limited Lifetime” in the table below is defined as: 20 years from the beginning date of warranty coverage for
gas appliances, and 10 years from the beginning date of warranty coverage for wood, pellet, and coal appliances. These
time periods reflect the minimum expected useful lives of the designated components under normal operating conditions.
Warranty Period
Parts
Labor
1 Year
2 years
HHT Manufactured Appliances and Venting
Gas
X
X
Wood
X
X
X
3 years
Pellet
EPA
Wood
Coal
X
X
X
X
X
X
X
X
X
X
Igniters, electronic components,
and glass
Factory-installed blowers
Molded refractory panels
Firepots and burnpots
1 year
7 years
3 years
10
years
1 year
X
Limited
3 years
Lifetime
X
X
X
X
X
90 Days
X
X
X
X
X
Page 54
X
All parts and material except as
covered by Conditions,
Exclusions, and Limitations
listed
X
5 years
Page
42
4021-645C 12-29-10
Components Covered
Electric Venting
X
X
X
Castings and baffles
X
X
Manifold tubes,
HHT chimney and termination
Burners, logs and refractory
Firebox and heat exchanger
X
X
See conditions, exclusions, and limitations on next page.
7039-131I
7022-122
All replacement parts
beyond warranty period
February 20,
2011
Page
1 of 2
January 19, 2011
2100 Millennium Wood Stove (ACC)
R
Castile Pellet Insert
WARRANTY CONDITIONS:
��
��
��
��
����������������������������������������������������������������������������������������������������������������������
����������������������������������������������������������������
�������������������������������������������������������������������������������������������������
����������������������������������������������������������������������������������������������������������������������������
���������������������������������������������������������������������������������������������������������������������
�����������������������������������������������������������������������������������
�������������������������������������������������������������������������������������������������������������������
�������������������������������������������
WARRANTY EXCLUSIONS:
�������������������������������������������
�� ���������������������������������������������������������������������������������������������������������������������
������������������������������������������������������������������������������������������
�� ��������������������������������������������������������������������������������������������������������������������
�����������������������������������������������������������������������������������������������������������������
�� ����������������������������������������������������������������������������������������������������������������
����������������������������������������������������������������������������������������������������������������������������������������
�� ����������������������������������������������������������������������������������������������������������������������������������������������������������������������������
�� �����������������������������������������������������������������������������������������������������������������������
��������������������������������������������������������������������������������������������������������������������������
�����������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������
��������������������������������������������������������������������������������������������������������������������
���������������������������������������������������������������������������������������������������������������������
�������������������������������������������������������������������������������������������������������������������������
�������������������������������������������������������������������������������������������������������������������
����������������������������������������������������������������������������������������������������������������
�������������������������������������������������������������������������������������
�� ����������������������������������������������������������������������������������������������������������
�� ����������������������������������������������������������������������������������������������������������
�� ������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������
���������������
This warranty is void if:
��
��
��
�������������������������������������������������������������������������������������������������������������������
���������������������������������������������������������������������������������������������������������������������������
�������������������������������������������������������
����������������������������������������������������������������������������
�������������������������������������������������������������������������������������������������������������������
����������������������������������������������������������
LIMITATIONS OF LIABILITY:
��
�����������������������������������������������������������������������������������������������������������������
��������������������������������������������������������������������������������������������������������������������������
��������������������������������������������������������������������������������������������������������������������
������������������������������������������������������������������������������������������������������������������������
�������������������������������������������������������������������������������������������������������������������
������������������������������������������������������������������������������������
�������������������������������������������������������������������������������������
�����������������������������������
February 20, 2011
4021-645C 12-29-10
January 19, 2011
7039-131I
7022-122
Page 43
Page 2 of 2
Page 55
CONTACT INFORMATION:
Hearth & Home Technologies
1445 North Highway
Colville, WA 99114
Division of HNI INDUSTRIES
Please contact your Quadra-Fire dealer with any questions or concerns.
For the number of your nearest Quadra-Fire dealer,
visit our web site at www.quadrafire.com
NOTICE
D
DI O N
SC O
AR T
D
DO NOT DISCARD THIS MANUAL
• Important operating
and maintenance
instructions included.
• Read, understand and
follow these instructions
for safe installation and
operation.
• Leave this manual with
party responsible for
use and operation.
We recommend that you record the following pertinent
information for your 2100 MILLENNIUM WOOD STOVE (ACC)
Date purchased/installed: Serial Number: Location on appliance: Dealership purchased from: Dealer phone: Notes: This product may be covered by one or more of the following patents: (United States) 4593510, 4686807, 4766876, 4793322, 4811534,
5000162, 5016609, 5076254, 5113843, 5191877, 5218953, 5263471, 5328356, 5341794, 5347983, 5429495, 5452708, 5542407,
5601073, 5613487, 5647340, 5688568, 5762062, 5775408, 5890485, 5931661, 5941237, 5947112, 5996575, 6006743, 6019099,
6048195, 6053165, 6145502, 6170481, 6237588, 6296474, 6374822, 6413079, 6439226, 6484712, 6543698, 6550687, 6601579,
6672860, 6688302B2, 6715724B2, 6729551, 6736133, 6748940, 6748942, 6769426, 6774802, 6796302, 6840261, 6848441, 6863064,
6866205, 6869278, 6875012, 6880275, 6908039, 6919884, D320652, D445174, D462436; (Canada) 1297749, 2195264, 2225408,
2313972; (Australia) 780250, 780403, 1418504 or other U.S. and foreign patents pending.
Page 44
7039-131I
February 20, 2011