IPC-602
2U 6-slot Industrial
Rackmount Chassis
User’s Manual
Copyright Notice
This document is copyrighted, September 2004, by Advantech Co., Ltd.
All rights are reserved. Advantech Co., Ltd. reserves the right to make
improvements to the products described in this manual at any time without notice.
No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of
Advantech Co., Ltd. Information provided in this manual is intended to
be accurate and reliable. However, Advantech Co., Ltd. assumes no
responsibility for its use, nor for any infringements upon the rights of
third parties which may result from its use.
Acknowledgements:
• Intel®, Pentium® 4, and Celeron® are trademarks of Intel Corporation.
• IPC-602, PCA-6105P4V, PCA-6106P3V, PCA-6106P3VX and PCA6106P4V are trademarks of Advantech Co., Ltd.
All other product names or trademarks are the properties of their respective owners.
On-line Technical Support
For technical support and service, please visit our support website at:
http://www.advantech.com/support
IPC-602 User’s Manual
ii
Part No. 2002060201
3rd. Edition
Printed in Taiwan
September 2004
A Message to the Customer
Advantech customer services
Each and every Advantech product is built to the most exacting specifications to ensure reliable performance in the harsh and demanding conditions typical of industrial environments. Whether your new Advantech
equipment is destined for the laboratory or the factory floor, you can be
assured that your product will provide the reliability and ease of operation
for which the name Advantech has come to be known.Your satisfaction is
our primary concern. Here is a guide to Advantech’s customer services.
To ensure you get the full benefit of our services, please follow the
instructions below carefully.
Technical support
We want you to get the maximum performance from your products. So if
you run into technical difficulties, we are here to help. For the most frequently asked questions, you can easily find answers in your product documentation. These answers are normally a lot more detailed than the ones
we can give over the phone.
So please consult this manual first. If you still cannot find the answer,
gather all the information or questions that apply to your problem, and
with the product close at hand, call your dealer. Our dealers are well
trained and ready to give you the support you need to get the most from
your Advantech products. In fact, most problems reported are minor and
are able to be easily solved over the phone.
In addition, free technical support is available from Advantech engineers
every business day. We are always ready to give advice on application
requirements or specific information on the installation and operation of
any of our products.
iii
Product warranty
Advantech warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship for two years
from the date of purchase.
This warranty does not apply to any products which have been repaired or
altered by persons other than repair personnel authorized by Advantech,
or which have been subject to misuse, abuse, accident or improper installation. Advantech assumes no liability under the terms of this warranty as
a consequence of such events.
If an Advantech product is defective, it will be repaired or replaced at no
charge during the warranty period. For out-of-warranty repairs, you will
be billed according to the cost of replacement materials, service time and
freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
Step 1. Collect all the information about the problem encountered. (For
example, type of PC, CPU speed, Advantech products used,
other hardware and software used, etc.) Note anything abnormal
and list any on-screen messages you get when the problem
occurs.
Step 2. Call your dealer and describe the problem. Please have your manual, product, and any helpful information readily available.
Step 3. If your product is diagnosed as defective, obtain an RMA (return
material authorization) number from your dealer. This allows us
to process your return more quickly.
Step 4. Carefully pack the defective product, a fully-completed Repair
and Replacement Order Card and a photocopy proof of purchase
date (such as your sales receipt) in a shippable container. A product returned without proof of the purchase date is not eligible for
warranty service.
Step 5. Write the RMA number visibly on the outside of the package and
ship it prepaid to your dealer.
IPC-602 User’s Manual
iv
Initial Inspection
Before you begin installing your backplane, please make sure that the following materials have been shipped:
• IPC-602 Chassis
• User's Manual
• Warranty card
• Accessory package with screws for disk drives and backplane, a pair of
keys and a spare filter
If any of these items are missing or damaged, contact your distributor or
sales representative immediately. We have carefully inspected the IPC602 mechanically and electrically before shipment. It should be free of
marks and scratches and in perfect working order upon receipt. As you
unpack the IPC-602, check it for signs of shipping damage. (For example,
damaged box, scratches, dents, etc.) If it is damaged or it fails to meet the
specifications, notify our service department or your local sales representative immediately. Also notify the carrier. Retain the shipping carton and
packing material for inspection by the carrier. After inspection, we will
make arrangements to repair or replace the unit.
v
IPC-602 User’s Manual
vi
Contents
Chapter
1 General Information ........................................2
1.1
1.2
Introduction ....................................................................... 2
Specifications .................................................................... 2
1.2.1
1.2.2
1.2.3
Passive Backplane Options............................................. 2
Power Supply Options .................................................... 3
Environmental specifications.......................................... 3
1.3
Dimensions........................................................................ 4
1.4
Safety Precautions ............................................................ 5
Figure 1-1:Dimension Diagram ...................................... 4
Chapter
2 System Setup.....................................................8
2.1
2.2
Introduction ....................................................................... 8
Removing the Cover.......................................................... 8
2.3
Installing Disk Drives....................................................... 9
2.4
Installing Plug-in Cards................................................... 10
2.5
Replacing the Fan............................................................ 11
2.6
Replacing the Filter ......................................................... 11
2.7
Installing the L form holder ............................................ 12
Figure 2-1:Removing the cover ...................................... 8
Figure 2-2:Installing disk drives .................................... 9
Figure 2-3:Installing plug-in cards ............................... 10
Figure 2-4:Replacing the fan ........................................ 11
Figure 2-5:Replacing the filter...................................... 12
Figure 2-6:L form holders............................................. 12
Appendix A
Optional Passive Backplanes........................14
A.1
A.2
A.3
PCA-6105PV4: 4 PCI / 1 CPU slots ............................... 14
PCA-6106P3V: 1 ISA / 3 PCI / 2 PICMG slots.............. 16
PCA-6106PV4: 1 ISA / 4 PCI / 1 CPU slots................... 18
Appendix B Parts Ordering Guide ...................................22
Appendix C Safety Instructions .........................................26
C.1
C.2
English............................................................................. 26
German - Wichtige Sicherheishinweise .......................... 27
vii
AIMB-744 User’s Manual
viii
CHAPTER
1
General Information
1
Chapter 1 General Information
1.1 Introduction
The IPC-602 is a compact rugged 19" 2U-height rackmount chassis designed for space-limited application. With its rugged, sturdy
and well-cooled steel chassis specially designed to withstand
heavy shocks and thick dust, the IPC-602 can be used in the harshest of environments. It is ideal for Computer Telephony or network
system configurations that require high availability within a limited space, such as computer telephony and networking systems.
1.2 Specifications
• Construction: Heavy-duty steel
• Disk drive capacity: One 5.25" and two 3.5" drive bays
• Indicators: LEDs for power On/Off, and HDD
• Controls: Power On and Reset switches on front panel
• Cooling fan: Two 42 CFM fans on front panel, with air filters
• Weight: 8.3 kg (18.26 lbs) without power supply
• Dimensions (W x D x H): 481.2 x 449.5 x 88 mm (19" x
17.7" x 4")
• Interior paint color: Black 2U, 2X; Fabric Texture
1.2.1 Passive Backplane Options
Part Number
Slots
PC Board
PCA-6105P4V
4 PCI / 1 PICMG
PCA-6106P4V
1 ISA / 4 PCI / 1 PICMG
PCA-6106P3V
1 ISA / 3 PCI / 2 PICMG
6-layer PCB with ground and
LEDs for +5 V,
power planes for reducing noise
+12 V, -5 V, -12 V,
and low power-supply imped+3.3 V
ance
IPC-602 User’s Manual
2
Indicators
1.2.2 Power Supply Options
Part Number Watt
PS-300ATXDC48
Input
Output
300 W DC -36 ~ -72 V +5 V @ 30 A
+12 V @ 15 A
-5 V @ 0.3 A
-12 V @ 0.8 A
+5 Vsb @ 2 A
PS-260-610E 260 W AC 110/220 V
(AT)
+5 V @ 25 A
+12 V @ 9 A
-5 V @ 0.5 A
-12 V @ 2 A
PS-250ATX-Z 250 W AC 95 ~ 132 V +5 V @ 27 A
(ATX, PFC)
AC 190 ~ 264 V +3.3 V @ 20 A
(Selectable)
+12 V @ 13 A
-12 V @ 0.8 A
-5 V @ 0.3 A
+5 Vsb @ 2 A
Mini-load
Safety
MTBF
+5 V @ 0.3 A
+3.3V @ 0.3A
+12V @ 0.2A
UL/CSA/CE/TUV/
FCC
100,000 hours
@25°C
+5 V @ 1 A
+12 V @ 0.1 A
UL/CSA/CE/TÜV
140,000 hours
@ 50 °C full
load
+5 V @ 1.5 A
+12 V @ 0.3 A
UL/cUL (60950
100,000 hours
3rd)/ CE
@ 25 °C full
(EN61000-3-2
load
Class D)/TUV/FCC/
CSA/Nemko/CB/
CCC
PS-400ATX-Z 400 W AC 90 ~ 264V
(ATX, PFC)
(Full-range)
+5 V @ 42 A,
+5 V @ 2 A
UL/cUL/TUV/CCC
+3.3 V @ 20 A
+12 V @ 0.5 A
+12 V @ 14 A
+3.3 V @ 0.2 A
-12 V @ 1 A
-5 V @ 1 A
+5 Vsb @ 0.75 A
PS-300ATXZB (ATX,
PFC)
+5 V @ 30 A,
+3.3 V @ 28 A
+12 V @ 15 A
-12 V @ 0.8 A
-5 A @ 0.3 A,
+5 Vsb @ 2 A
300W
AC 90-264 V
(Full range)
100,000 hours
@ 25 °C 75 %
load
100,000 hours
+5 V @ 0.1 A
UL/cUL (60950
+3.3 V @ 0.3 A 3rd)/CE (EN61000- @ 25 °C
3-2 Class D)/TUV/
FCC/CSA/Nemko/
CB/CCC
1.2.3 Environmental specifications
• Operating temperature: 0 ~ 45° C (32 ~ 113° F)
• Relative humidity: 10 ~ 95% @ 40° C, non-condensing
• Safety: CE compliant, UL / cUL certified
3
1.3 Dimensions
unit: mm [inch]
Figure 1-1: Dimension Diagram
IPC-602 User’s Manual
4
1.4 Safety Precautions
Warning!
Always completely disconnect the power cord
from your chassis whenever you work with the
hardware. Do not make connections while the
power is on. Sensitive electronic components
can be damaged by sudden power surges. Only
experienced electronics personnel should open
the PC chassis.
Caution!
Always ground yourself to remove any static
charge before touching the backplane, motherboard or add-on cards. Modern electronic
devices are very sensitive to static electric
charges. As a safety precaution, use a grounding wrist strap at all times. Place all electronic
components on a static-dissipative surface or in
a static-shielded bag when they are not in the
chassis.
Caution!
The computer is provided with a battery-powered Real-time Clock circuit. There is a danger
of explosion if battery is incorrectly replaced.
Replace only with same or equivalent type recommended by the manufacturer. Discard used
batteries according to manufacturer's instructions.
Caution!
There is a danger of a new battery exploding if
it is incorrectly installed. Do not attempt to
recharge, force open, or heat the battery.
Replace the battery only with the same or
equivalent type recommended by the manufacturer. Discard used batteries according to the
manufacturer’s instructions.
5
This device complies with the requirements in part
15 of the FCC rules: Operation is subject to the following two conditions:
1.This device may not cause harmful interference,
and
2.This device must accept any interference
received, including interference that may cause
undesired operation
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance
with the instruction manual, may cause harmful
interference to radio communications. Operation of
this device in a residential area is likely to cause
harmful interference in which case the user will be
required to correct the interference at his/her own
expense. The user is advised that any equipment
changes or modifications not expressly approved
by the party responsible for compliance would void
the compliance to FCC regulations and therefore,
the user's authority to operate the equipment.
IPC-602 User’s Manual
6
CHAPTER
2
System Setup
7
Chapter 2
Chapter 2 System Setup
2.1 Introduction
The following procedures are provided to assist you in installing drives
and plug-in cards into the IPC-602.
2.2 Removing the Cover
Unscrew the six screws on the front and rear panels, then slide the top
cover toward the rear chassis and open it. See Figure 2-1 below:
Figure 2-1: Removing the cover
IPC-602 User’s Manual
8
2.3 Installing Disk Drives
After removing the cover, you can easily install disk drives. Please refer
to Figure 2-2 below and do the following:
1. Remove the four outer screws which mount the drive bay to the chassis.
2. Slide the drive bay backwards to a location where it is not obstructed
by the top rim. Lift it free from the chassis.
3. Remove the front cover of the drive bay, and insert the drives into the
proper locations in the drive bay.
4. Put back the drive bay properly and fasten the screws.
Figure 2-2: Installing disk drives
9
Chapter 2
2.4 Installing Plug-in Cards
After removing the cover, you can easily install plug-in cards by following the steps. Please refer to Figure 2-3 below:
1. Unscrew the screws on the card cage.
2. Insert the CPU card carefully into the PICMG slot and then fix it by
screwing it into the card bracket. You can also fix the other edge of
the CPU card using the supplied small L-form holder.
3. If users need to insert other cards on the other side of the backplane,
please loosen the L-form support first. After installing the cards, also
fix them to the card cage by screwing them into the card bracket. Then
replace the L-form support and fasten it.
4. After all cards are installed completely, put card cage back into the
correct location in the chassis. Finally, fasten the screws.
Figure 2-3: Installing plug-in cards
IPC-602 User’s Manual
10
2.5 Replacing the Fan
1. Unscrew the two screws on the fan bracket, and slide the bracket backwards. See Figure 2-4 below:
2. Replace the new fan and fix it to the bracket.
3. Put back the fan bracket and fasten the screws.
Figure 2-4: Replacing the fan
2.6 Replacing the Filter
The filter is located next to the lockable door. If IPC-602 is under use
constantly, the filter should be changed about once a month. To replace
the filter, refer to Figure 2-5 below and do the following:
1. Open the lockable door.
2. Remove the filter by gently pulling the tab and sliding the filter rightwards.
3. Slide a new filter in until it snaps into place.
4. Close and lock the lockable door.
11
Chapter 2
Figure 2-5: Replacing the filter
2.7 Installing the L form holder
Before users mounting IPC-602 Chassis to the rack, please install the L
form holders to both sides of the chassis. Please refer to Figure 2-6 and
proceed as following steps.
1.
Find the L form holders and the screws from the accessory package.
2.
Put the holder to the correct location and fasten the screws to the
chassis.
Figure 2-6: L form holders
IPC-602 User’s Manual
12
Appendix
A
Optional
Passive Backplanes
13
Appendix A
Appendix A Optional Passive Backplanes
A.1 PCA-6105PV4: 4 PCI / 1 CPU slots
Dimensions: 260 x 80 mm
1. Connectors
Connector
CPC1
PCI 1~4
CN2
CN1
CN3
KB1
KB3
ATX1
Description
PICMG connectors
32 bit PCI BUS connectors (primary)
8-PIN +12V, -12V, +3.3V, +5V, -5V, GND and 5VSB connector
3-PIN PS_ON, GND and 5VSB for ATX power
3-PIN +12V, GND and +5V DC power connector
To CPU card K/B connector
To front part K/B connector
ATX Power connector
IPC-602 User’s Manual
14
2. Pin Definition
CN1
Pin
1
2
3
Name
PS-ON
GND
5VSB
CN3
Pin
1
2
3
Name
+12V
GND
+5V
FAN1
Pin
1
2
3
Name
NC
+12V
GND
ATX1
Pin
1
2
3
4
5
6
7
8
9
10
Name
+3.3V
+3.3V
GND
+5V
GND
+5V
GND
NC
5VSB
+12V
Pin
11
12
13
14
15
16
17
18
19
20
CN2
Pin
1
2
3
4
5
6
7
8
Name
5VSB
GND
GND
-5V
+5V
+3.3V
-12V
+12V
KB1, KB3
Pin
Name
1
KBCLK
2
KB-DT
3
NC
4
GND
5
+5V
Name
+3.3V
-12V
GND
PS-ON
GND
GND
GND
-5v
+5V
+5V
3. PCI Routing table
PCI Slot
ID SEL
PCI1
PCI2
PCI3
PCI4
AD31
AD30
AD29
AD28
PCI
INTA
INTB
INTC
INTD
INTA
15
interrupt
INTB
INTC
INTD
INTA
INTB
pin
route
INTC
INTD
INTA
INTB
INTC
INTD
INTA
INTB
INTC
INTD
Appendix A
A.2 PCA-6106P3V: 1 ISA / 3 PCI / 2 PICMG slots
Dimensions: 260 x 80 mm
15.875
3
21
20.32
20.32
D18
12.9
12
22.11
15.62
12
15
260
84.8
160
8.13
32.89
15
CN2
1
ATX
10
PG
+5V
+12
-12
GND
-5V
+5V
P8-P9
KB1
18.29
KB3
11
20
CN3
80
61.47
73.28
20.32
CN1
20.32
No circuit area
3
3
21
No circuit area
1. Connectors
Connector
ISA1, ISA3
ISA2
PICMG1,PICMG2
PCI1~PCI3
VKB1
VKB2,VKB3
VAT1
VATX1
HCN1
HCN2
HCN3
IPC-602 User’s Manual
Description
ISA connector for PICMG slot (PCI slot is
PICMG1,PICMG3)
ISA connector
PCI connector for PICMG slot
32 bit PCI slot
KB-In, from CPU card K/B connector
KB-Out, 5 pin external K/B connector
AT power connector 90D
ATX Power connector 90D
PS-ON Function, to CPU card for ATX Power signal, 3 pin
connector
8 pin Alarm Board Power connector
3 pin +5V and +12V Power connector
16
2. Pin Definition
VKBA1,VKBA2,VKBA3;
Pin
Name
1
KBCLK
2
KBDATA
3
NC
4
KBGND
5
KBVCC
HCN1
Pin
1
2
3
Name
PS-ON
GND
5VSB
HCN2
Pin
1
2
3
4
5
6
7
8
Name
5VSB
GND
GND
-5V
+5V
+3.3V
-12V
+12V
HCN3
Pin
1
2
3
Name
+12V
GND
+5V
VATX1
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Name
+3.3V
+3.3V
GND
+5V
GND
+5V
GND
NC
5VSB
+12V
+3.3V
-12V
GND
PS-ON
GND
GND
GND
-5V
+5V
+5V
VAT1
Pin
1
2
3
4
5
6
7
8
9
10
11
12
Name
NC
+5V
+12V
-12V
GND
GND
GND
GND
-5V
+5V
+5V
+5V
3. PCI Routing table
PCI Slot
ID SEL
PCI1
PCI2
PCI3
AD30
AD29
AD28
PCI
INTA
INTC
INTD
INTA
17
interrupt
INTB
INTD
INTA
INTB
pin route
INTC
INTA
INTB
INTC
INTD
INTB
INTC
INTD
Appendix A
A.3 PCA-6106PV4: 1 ISA / 4 PCI / 1 CPU slots
Dimensions: 260 x 80 mm
1. Connectors
Connector
ISA1~ISA2
PPCI1~PPCI4
PICMG1
ATX1
KB1
KB2~KB3
CN1
CN2
CN3
Description
16 bit ISA Bus connector
32 bit PCI Bus connector (Primary Group)
PICMG connector
ATX Power connector
KB-In, from CPU card K/B connector
KB-Out, 5 pin external K/B connector
PS-ON Function, to CPU card for ATX power signal, 3 pin
8 pin Alarm Board Power connector
8 pin +5V and +12V FAN connector
IPC-602 User’s Manual
18
2. Pin Definition
CN1
PIN
1
2
3
Name
PS-ON
GND
5VSB
CN2
PIN
1
2
3
4
5
6
7
8
Name
5VSB
GND
GND
-5V
+5V
+3.3V
-12V
+12V
CN3
PIN
1
2
3
ATX1
PIN
1
2
3
4
5
6
7
8
9
10
Name
+3.3V
+3.3V
GND
+5V
GND
+5V
GND
NC
5VSB
+12V
PIN
11
12
13
14
15
16
17
18
19
20
Name
+3.3V
-12V
GND
PS-ON
GND
GND
GND
-5V
+5V
+5V
Name
+12V
GND
+5V
KB~1/2/3
PIN
Name
1
KBCLK
2
KBDAT
3
NC
4
KBGND
5
KBVCC
3. PCI Routing table
PCI Slot
PPCI1
PPCI2
PPCI3
PPCI4
IDSEL
AD31
AD30
AD29
AD28
PCI Interrupt Pin Route
INT A
INT B
INT C
INT B
INT C
INT D
INT C
INT D
INT A
INT D
INT A
INT B
INT A
INT B
INT C
19
INT D
INT A
INT B
INT C
INT D
Appendix A
IPC-602 User’s Manual
20
Appendix
B
Parts Ordering Guide
21
Appendix B
Appendix B Parts Ordering Guide
Code
1
Part No.
1960000404
Q’ty Description
1
TOP COVER
Code
22
2
1902610682
1
23
Q’ty Description
1
FILTER HOUSING
199902K000 1
FILTER PE
3
4
1960000444
1962011390
1
1
24
25
1992601085
1960000445
1
1
LOCK SETS
FRONT PLATE
5
1962650600
1
26
1962002810
1
6
1962002760
1
27
1759400200
1
LOCKABLE
DOOR
SPEAKER
7
1962002740
2
28
1962002700
2
8
9
9686610603
1962002730
1
1
29
30
1994000060
2
1
10
1759081200
2
31
1962011510
1
11
9692A10000
1
32
196202K130 1
12
13
199902K000
1995000090
1
1
IPC-602 User’s Manual
BACKPLANE
BASE
CHASSIS
5.25” DISK
COVER
3.5” DISK
COVER
DISK DRIVE
HOUSING
HDD
BRACKET
BACKPLANE
FAN
BRACKET
DUAL FAN
PS/2 K/B &
USB PCB
FILTER PE
FILTER
HOUSING
22
Part No.
1995000090
LED LAMP
HOLDER
LED HOUSING
HDD
PCI CARD
BRACKET
CPU CARD
HOLDER
14
1653104030
1
15
1703020550
1
16
1601000001
1
17
1602002100
1
18
1962002770
2
19
1962002790
1
20
21
1962002800
1962610130
1
2
ATX POWER
SUPPLY
WIRE MOUNT
HOLE
RESET BUTTON
POWER
SWITCH
SIDE FIXING
HOLDER
FRONT WINDOW
BEZEL
HINGE
Code
Part No.
Q’ty
A
193900036
16
B
1939006320
8
Screw Description
HEX/W
M3x0.5x5L
HEX/W#6-32
C
1935330400
6
R/W M3x0.5x5L
D
0939000410
8
R/W M4x0.7x5L
E
1930030500
17
FLAT M3x0.5x5L
F
G
1931040620
1939000515
8
8
FLAT M4x0.7x5L
Accessory Options
Part Number
SCD-FDD-COMBO
Descriptions
Storage kit with slim 24X CD-ROM and standard 3.5”
black FDD
5.25" compact storage kit with slim 24X CD-ROM and
a 3.5" drive bay for FDD or HDD
3.5" FDD with black bezel
HDD cable, ATA 66/100, 45 cm + 20 cm
Low profile P4 CPU cooler up to 3.2 GHz
Low profile P4 CPU cooler up to 2.8 GHZ
SCD COMBO 5.25
9684000014
1701400652
1750000073
1759214200
Ordering Information
Part Number
IPC-602P3-00PB
IPC-602P3-00XB
IPC-602P3-25ZB
IPC-602P3-26PB
IPC-602P3-30ZB
IPC-602P4-00XB
IPC-602P4-25ZB
IPC-602P4-30ZB
With Power Supply
Without power supply,
with AT switch
Without power supply,
with ATX switch
PS-250ATX-Z
PS-260-610E
PS-300ATX-ZB
Without power supply,
with ATX switch
PS-250ATX-Z
PS-300ATX-ZB
23
With Backplane
PCA-6106P3V-0B1
Regulation
None
PCA-6106P3V-0B1
None
PCA-6106P3V-0B1
PCA-6106P3V-0B1
PCA-6106P3V-0B1
PCA-6105P4V-0B2
UL, cUL, CE
UL, cUL, CE
UL, cUL, CE
None
PCA-6105P4V-0B2
PCA-6105P4V-0B2
UL, cUL, CE
UL, cUL, CE
Appendix B
IPC-602 User’s Manual
24
Appendix
C
Safety Instructions
25
Appendix C
Appendix C Safety Instructions
C.1 English
1. Read these safety instructions carefully.
2. Keep this user's manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning. Do not
use liquid or spray detergents for cleaning. Use a damp cloth.
4. For plugable equipment, the power outlet must be installed near the
equipment and be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it
or letting it fall could cause damage.
7. The openings on the enclosure are for air convection. Protect the equipment from overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before connecting
the equipment to the power outlet.
9. Position the power cord so that people cannot step on it. Do not place
anything over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the
power source to avoid damage by transient over voltage.
12. Never pour any liquid into an opening. This could cause fire or electrical shock.
13. Never open the equipment. For safety reasons, the equipment should
be opened only by qualified service personnel.
14. If any of the following situations arises, get the equipment checked by
service personnel:
a.
The power cord or plug is damaged.
b.
Liquid has penetrated into the equipment.
c.
The equipment has been exposed to moisture.
d.
The equipment does not work well, or you cannot get it to
work according to the installation reference guide.
e.
The equipment has been dropped and damaged.
f.
The equipment has obvious signs of breakage.
IPC-602 User’s Manual
26
15. DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED
ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS
BELOW -20° C (-4° F) OR ABOVE 60° C (140° F). THIS MAY DAMAGE THE EQUIPMENT.
The sound pressure level at the operator's position according to IEC 7041:1982 is equal to or less than 70 dB(A).
DISCLAIMER: This set of instructions is given according to IEC 704-1.
Advantech disclaims all responsibility for the accuracy of any statements contained herein.
C.2 German - Wichtige Sicherheishinweise
1. Bitte lesen Sie Sich diese Hinweise sorgfältig durch.
2. Heben Sie diese Anleitung für den späteren Gebrauch auf.
3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie Keine Flüssig-oder Aerosolreiniger. Am besten dient ein
angefeuchtetes Tuch zur Reinigung.
4. Die Netzanschlußsteckdose soll nahe dem Gerät angebracht und leicht
zugänglich sein.
5. Das Gerät ist vor Feuchtigkeit zu schützen.
6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein
Kippen oder Fallen könnte Verletzungen hervorrufen.
7. Die Belüftungsöffnungen dienen zur Luftzirkulation die das Gerät vor
überhitzung schützt. Sorgen Sie dafür, daß diese Öffnungen nicht abgedeckt werden.
8. Beachten Sie beim Anschluß an das Stromnetz die Anschlußwerte.
9. Verlegen Sie die Netzanschlußleitung so, daß niemand darüber fallen
kann. Es sollte auch nichts auf der Leitung abgestellt werden.
10. Alle Hinweise und Warnungen die sich am Geräten befinden sind zu
beachten.
11. Wird das Gerät über einen längeren Zeitraum nicht benutzt, sollten
Sie es vom Stromnetz trennen. Somit wird im Falle einer Überspannung
eine Beschädigung vermieden.
12. Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder Flüssigkeiten in das Gerät gelangen. Dies könnte einen Brand bzw. elektrischen Schlag auslösen.
27
Appendix C
13. Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen Sicherheit nur von authorisiertem Servicepersonal geöffnet werden.
14. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu
trennen und von einer qualifizierten Servicestelle zu überprüfen:
a. Netzkabel oder Netzstecker sind beschädigt.
b. Flüssigkeit ist in das Gerät eingedrungen.
c. Das Gerät war Feuchtigkeit ausgesetzt.
d. Wenn das Gerät nicht der Bedienungsanleitung entsprechend funktioniert oder Sie mit Hilfe dieser Anleitung keine Verbesserung erzielen.
e. Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt.
f. Wenn das Gerät deutliche Anzeichen eines Defektes aufweist.
15. Bitte lassen Sie das Gerät nicht unbehehrt hinten unter -20° C (-4° F)
oder oben 60° C (140° F), weil diesen Temperaturen das Gerät zerstören
könten.
Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000
beträgt 70dB(A) oder weiger.
DISCLAIMER: This set of instructions is provided according to
IEC704-1. Advantech disclaims all responsibility for the accuracy of
any statements contained herein.
IPC-602 User’s Manual
28