VoIPon Gigabit Color User guide

N600 Dual Band WiFi Gigabit
Modem Router with Voice
NB16WV-02
USER GUIDE
Copyright
Copyright©2013 NetComm Wireless Limited. All rights reserved.
The information contained herein is proprietary to NetComm Wireless Limited. No part of this document may be translated,
transcribed, reproduced, in any form, or by any means without prior written consent of NetComm Wireless Limited.
Please note: This document is subject to change without notice.
Save Our Environment
When this equipment has reached the end of its useful life, it must be taken to a recycling centre and processed separately from
domestic waste.
The cardboard box, the plastic contained in the packaging, and the parts that make up this device can be recycled in accordance
with regionally established regulations. Never dispose of this electronic equipment along with your household waste. You may be
subject to penalties or sanctions under the law. Instead, ask for disposal instructions from your municipal government.
Please be responsible and protect our environment.
This manual covers the following products:
NetComm Wireless NB16WV-02
DOCUMENT VERSION
1.0 Initial document release
1.1 Updated to include WPS button function description
1.2 Updated to NCMZ0_1016_04231050
DATE
1 May 2013
24 November 2014
6 May 2015
Table 1 - Document Revision History
www.netcommwireless.com
Ver 1.2
NetComm Wireless NB16WV-02 User Guide
2
Table of Contents
Table of Contents ..........................................................................................................................................................................3
Overview.........................................................................................................................................................................................5
Introduction ................................................................................................................................................................................................... 5
Target Users.................................................................................................................................................................................................. 5
Prerequisites ................................................................................................................................................................................................. 5
VoIP Telephony Requirements ............................................................................................................................................................... 5
Notation ........................................................................................................................................................................................................ 5
Product Introduction ......................................................................................................................................................................6
Product Overview .......................................................................................................................................................................................... 6
Package Contents ......................................................................................................................................................................................... 6
Product Features ........................................................................................................................................................................................... 7
Physical Dimensions and Indicators .............................................................................................................................................8
LED Indicators ............................................................................................................................................................................................... 8
Physical Dimensions ...................................................................................................................................................................................... 9
NB16WV-02 Default Settings ......................................................................................................................................................................... 9
Interfaces .....................................................................................................................................................................................10
Safety and Product Care .............................................................................................................................................................11
Transport and Handling ...............................................................................................................................................................11
Installation and Configuration of the NB16WV-02 ......................................................................................................................12
Placement of your NB16WV-02 ................................................................................................................................................................... 12
Avoid obstacles and interference.................................................................................................................................................................. 12
Cordless Phones ......................................................................................................................................................................................... 12
Choose the “Quietest” Channel for your Wireless Network ............................................................................................................................ 12
Hardware installation ................................................................................................................................................................................... 13
Connecting via a cable................................................................................................................................................................................. 13
Connecting wirelessly .................................................................................................................................................................................. 13
Telephone Setup ......................................................................................................................................................................................... 13
Web Based Configuration Interface ............................................................................................................................................14
First-time Setup Wizard ............................................................................................................................................................................... 14
ADSL .................................................................................................................................................................................................. 15
Mobile Broadband ............................................................................................................................................................................... 16
WAN ................................................................................................................................................................................................... 16
Basic View .................................................................................................................................................................................................. 21
Status ................................................................................................................................................................................................. 21
Wireless 2.4GHz .................................................................................................................................................................................. 22
Wireless 5GHz ..................................................................................................................................................................................... 22
Mobile Broadband ............................................................................................................................................................................... 23
ADSL .................................................................................................................................................................................................. 23
Advanced Configuration............................................................................................................................................................................... 25
Status ................................................................................................................................................................................................. 25
Network Setup .................................................................................................................................................................................... 26
Forwarding Rules................................................................................................................................................................................. 44
Security Settings.................................................................................................................................................................................. 48
Advanced Settings .............................................................................................................................................................................. 55
VoIP Settings....................................................................................................................................................................................... 67
Call Features ....................................................................................................................................................................................... 72
NAS Settings ....................................................................................................................................................................................... 77
Toolbox ............................................................................................................................................................................................... 82
Additional Product Information ...................................................................................................................................................84
Establishing a wireless connection ............................................................................................................................................................... 84
Windows XP (Service Pack 3)............................................................................................................................................................... 84
Windows Vista ..................................................................................................................................................................................... 84
Windows 7 .......................................................................................................................................................................................... 84
Mac OSX 10.6 ..................................................................................................................................................................................... 84
Troubleshooting........................................................................................................................................................................................... 85
Using the indicator lights (LEDs) to Diagnose Problems ......................................................................................................................... 85
Technical Data .............................................................................................................................................................................85
Electrical Specifications................................................................................................................................................................................ 85
Environmental Specifications / Tolerances .................................................................................................................................................... 85
Legal & Regulatory Information ...................................................................................................................................................86
Intellectual Property Rights ........................................................................................................................................................................... 86
NetComm Wireless NB16WV-02 User Guide
3
www.netcommwireless.com
Ver 1.2
Customer Information .................................................................................................................................................................................. 86
Consumer Protection Laws .......................................................................................................................................................................... 86
Product Warranty ........................................................................................................................................................................................ 87
Limitation of Liability ..................................................................................................................................................................................... 87
Contact .........................................................................................................................................................................................88
www.netcommwireless.com
Ver 1.2
NetComm Wireless NB16WV-02 User Guide
4
Overview
Introduction
This manual provides information related to the installation, operation, and utilisation of the NB16WV-02.
Target Users
The individual reading this manual is presumed to have a basic understanding of telecommunications terminology and concepts.
Prerequisites
Before continuing with the installation of your NB16WV-02, please confirm that you comply with the minimum system
requirements below.
An activated ADSL, activated 3G, or configured Ethernet WAN connection.
Computer with Windows, Macintosh, or Linux-based operating systems with a working Ethernet adapter with TCP/IP
Protocol installed.
A Web Browser such as Internet Explorer, Google Chrome, Mozilla Firefox, Opera, Safari etc.
Wireless Computer System Requirements:
Computer with a working 802.11b, 802.11g or 802.11n wireless adapter.
VoIP Telephony Requirements
Standard analogue PSTN or cordless PSTN phone handset (DECT) with an RJ-11 port.
(ISDN phone handsets are not supported)
RJ-11 to RJ-11 phone connectivity cable
Subscription to a VoIP Service by a VoIP Service Provider using SIP version 1.0 or 2.0 (Session Initiation Protocol)
Notation
The following symbols are used in this manual:
Indicates a note requiring attention.
Indicates a note providing a warning.
Indicates a note providing useful information.
NetComm Wireless NB16WV-02 User Guide
5
www.netcommwireless.com
Ver 1.2
Product Introduction
Product Overview
Powerful dual-band wireless router with support for ADSL and 3G/4G Mobile Broadband.
Creates instant Wireless hotspots to share the Internet connection of a 3G/4G USB modem or DSL/Cable
connection.
Supports Wireless N standard with data speeds up to 600Mbps.
One Gigabit WAN port for alternate wired Internet connection (DSL/Cable/Satellite via Ethernet).
Four Gigabit LAN ports to connect wired devices like PCs or gaming consoles.
One RJ-11 port to connect an analogue telephone for use with a VoIP service.
Ensures connectivity and business continuity with auto Internet failover from ADSL to Ethernet WAN or 3G Mobile
Broadband.
Easy Wi-Fi Protected Setup (WPS) by the single touch of a button to establish a secure wireless connection
Full Wireless security - WEP, WPA, WPA2.
Browser based interface for configuration and management: OS independent and easy to use.
File server (FTP / NAS).
Download assistant.
Web HDD function.
Speeds are dependent on network coverage. See your 3G provider coverage maps for more details. The total number of Wi-Fi users can also affect data speeds.
Maximum wireless signal rate and coverage values are derived from IEEE Standard 802.11g and 802.11n specifications. Actual wireless speed and coverage are
dependent on network and environmental conditions included but not limited to volume of network traffic, building materials and construction/layout.
Package Contents
The NB16WV-02 package consists of:
N600 Dual Band WiFi Gigabit Modem Router with Voice - NB16WV-02.
Quick Start Guide.
Power Supply Unit.
Ethernet Cable (RJ-45).
Phone Cable (RJ-11).
Wireless Security Card.
Warranty Card.
If any of these items are missing or damaged, please contact NetComm Wireless Support immediately by visiting the NetComm
Wireless Support website at: http://www.netcommwireless.com/contact-forms/support
www.netcommwireless.com
Ver 1.2
NetComm Wireless NB16WV-02 User Guide
6
Product Features
The NetComm NB16WV-02 integrates an ADSL modem, dual-band wireless LAN, full Gigabit Ethernet interface and multifunctional USB port into one unit. Connection to the Internet is achieved through the ADSL modem, a 3G/4G service, fixed line or
via a connection to the NB16WV-02’s WAN port, providing you with the flexibility to choose how you access the Internet.
The NB16WV-02’s automatic failover ensures you are always connected by activating the 3G/4G connection should the ADSL or
Ethernet WAN connection drop out.
Users are able to share a single Internet connection via both a wired and wireless connection to the NB16WV-02. With a built in
antennas providing a 2 transmit, 2 receive (2T2R) 802.11n concurrent dual band wireless access point, this router provides
theoretical combined wireless speeds of up to 600Mbps.
On top of this, the NB16WV-02 has four gigabit LAN ports for high-speed wired connections to multiple devices. The NB16WV-02
allows you to simply insert a 3G/4G USB Modem with SIM card and utilise 3G/4G Mobile Broadband for Internet connectivity.
Integrated VoIP telephony enables the NB16WV-02 to offer a highly cost efficient solution for making interstate or overseas calls
using the mobile broadband connection, especially in locations that lack fixed line infrastructure or as an alternative to traditional
landline based Internet services. All you require is a traditional analogue/cordless phone and an activated account with a VoIP
service provider.
The NB16WV-02 also includes advanced security features such as VPN pass-through, a wide array of wireless security options
and a built in firewall.
NetComm Wireless NB16WV-02 User Guide
7
www.netcommwireless.com
Ver 1.2
Physical Dimensions and
Indicators
LED Indicators
The NB16WV-02 has been designed to be placed on a desktop. All of the cables exit from the rear for easy organization. The
display is visible on the front of the NB16WV-02 to provide you with information about network activity and the device status. See
below for an explanation of each of the indicator lights.
LED INDICATOR
Power
ADSL
3G
WWW
LAN 1-4
WAN
WIFI
VoIP
www.netcommwireless.com
Ver 1.2
ICON
COLOUR
DEFINITION
Off
The NB16WV-02 is powered off
Blue
The NB16WV-02 is powered on and operating normally
Blue Flashing
The NB16WV-02 is starting up
Off
No ADSL configuration present
Blue
The NB16WV-02 is connected to the Internet via an xDSL service
Blue Flashing
The NB16WV-02 is attempting to connect to the xDSL service
Off
No 3G/4G configuration present (or no 3G/4G dongle plugged in)
Red
SIM Error
Red Flashing
3G/4G connection failed - Retrying
Blue
The NB16WV-02 is connected to the Internet via a 3G/4G service
Blue Flashing
The NB16WV-02 is attempting to connect to the 3G/4G service
Off
No Internet configuration present
Red
The NB16WV-02 is connected via a 3G service
Flashing Red
Data is being sent or received via the 3G service
Blue
The NB16WV-02 is connected via an xDSL service
Flashing Blue
Data is being sent or received via the xDSL service
Purple
The NB16WV-02 is connected via an Ethernet WAN service
Flashing Purple
Data is being sent or received via the Ethernet WAN service
Off
No device is connected to the Ethernet LAN port
Blue
A device is connected to the Ethernet LAN port
Flashing Blue
Data is being sent or received via the Ethernet LAN port
Off
No device is connected to the Ethernet WAN port
Blue
A device is connected to the Ethernet WAN port
Off
WiFi is disabled on the NB16WV-02
Blue
WiFi is enabled on the NB16WV-02
Flashing Blue
The NB16WV-02 is waiting for a WPS PBC connection
Off
No VOIP service is configured
Blue
The NB16WV-02 is registered with the configured VOIP service
Flashing Blue
The NB16WV-02 is attempting to connect to the configured VOIP service
NetComm Wireless NB16WV-02 User Guide
8
Physical Dimensions
The following page lists the physical dimensions of the NB16WV-02.
37mm
145mm
215mm
NB16WV-02 DIMENSIONS
Length
215 mm
Width
145 mm
Height
37 mm
Weight
403 grams
NB16WV-02 Default Settings
The following tables list the default settings for the NB16WV-02.
LAN (MANAGEMENT)
Static IP Address:
192.168.20.1
Subnet Mask:
255.255.255.0
Default Gateway:
192.168.20.1
WIRELESS (WI-FI)
SSID:
(Refer to the included Wireless Security Card)
Security:
WPA-SPK/WPA2-PSK (mixed mode)
Security Key:
(Refer to the included Wireless Security Card)
NB16WV WEB INTERFACE ACCESS
Username:
admin
Password:
admin
NetComm Wireless NB16WV-02 User Guide
9
www.netcommwireless.com
Ver 1.2
Interfaces
The following interfaces are available on the NB16WV-02:
1
2
NUMBER
4
5
6
INTERFACE
7
8
9
DESCRIPTION
1
Power Jack
Connection point for the included power adapter. Connect the power supply here.
2
Power button
Turns the NB16WV-02 on or off.
3
USB 2.0 (File Sharing)
Connect a USB based storage device here.
4
USB 2.0 (3G/4G
Modem)
Connect a 3G/4G USB modem here.
5
WPS button
Activate the WiFi WPS function.
a) Hold for 1-3 seconds then release to trigger the 2.4GHz WPS
b) Hold for 4-6 seconds then release to trigger the 5GHz WPS
c) Hold for 15 seconds then release to reset the NB16WV-02 to factory default settings.
6
LAN 1-4
Gigabit Ethernet LAN ports. Connect your Ethernet based devices to one of these ports for highspeed internet access.
7
WAN
Gigabit WAN port for connection to a WAN network.
8
ADSL
Use the provided RJ-11 cable to connect the router to the telephone line operating your xDSL
service.
9
Telephone
Phone port for a standard PSTN analogue telephone handset. Connect a phone to this port to
make use of a VoIP service.
www.netcommwireless.com
Ver 1.2
3
NetComm Wireless NB16WV-02 User Guide
10
Safety and Product Care
With reference to unpacking, installation, use and maintenance of your electronic device, the following basic guidelines are
recommended:
Do not use or install this product near water to avoid fire or shock hazard. For example, near a bathtub, kitchen sink,
laundry tub, or near a swimming pool. Also, do not expose the equipment to rain or damp areas (e.g. a wet
basement).
Do not connect the power supply cord on elevated surfaces. Allow it to lie freely. There should be no obstructions in
its path and no heavy items should be placed on the cord. In addition, do not walk on, step on or mistreat the cord.
To safeguard the equipment against overheating, make sure that all openings in the unit that offer exposure to air are
unobstructed.
WARNING
Disconnect the power line from the device before servicing.
Transport and Handling
When transporting the NB16WV-02, it is recommended to return the product in the original packaging. This ensures the product
will not be damaged.
In the event the product needs to be returned, ensure it is securely packaged with appropriate padding to prevent
damage during courier transport.
NetComm Wireless NB16WV-02 User Guide
11
www.netcommwireless.com
Ver 1.2
Installation and Configuration of
the NB16WV-02
Placement of your NB16WV-02
The wireless connection between your NB16WV-02 and your WiFi devices will be stronger the closer your connected devices are
to your NB16WV-02. Your wireless connection and performance will degrade as the distance between your NB16WV-02 and
connected devices increases. This may or may not be directly noticeable, and is greatly affected by the individual installation
environment.
If you have concerns about your network’s performance that might be related to range or obstruction factors, try moving the
computer to a position between three to five meters from the NB16WV-02 in order to see if distance is the problem.
Please note: While some of the items listed below can affect network performance, they will not prohibit your wireless
network from functioning; if you are concerned that your network is not operating at its maximum effectiveness, this
checklist may help.
If you experience difficulties connecting wirelessly between your Wi-Fi Devices and your NB16WV-02, please try the following
steps:
In multi-storey homes, place the NB16WV-02 on a floor that is as close to the centre of the home as possible. This
may mean placing the NB16WV-02 on an upper floor.
Try not to place the NB16WV-02 near a cordless telephone that operates at the same radio frequency as the
NB16WV-02 (2.4GHz).
Avoid obstacles and interference
Avoid placing your NB16WV-02 near devices that may emit radio “noise,” such as microwave ovens. Dense objects that can
inhibit wireless communication include:
Refrigerators
Washers and/or dryers
Metal cabinets
Large aquariums
Metallic-based, UV-tinted windows
If your wireless signal seems weak in some spots, make sure that objects such as those listed above are not
blocking the signal’s path (between your devices and the NB16WV-02).
Cordless Phones
If the performance of your wireless network is impaired after considering the above issues, and you have a cordless phone:
Try moving cordless phones away from your NB16WV-02 and your wireless-enabled computers.
Unplug and remove the battery from any cordless phone that operates on the 2.4GHz band (check manufacturer’s
information). If this fixes the problem, your phone may be interfering with the NB16WV-02.
If your phone supports channel selection, change the channel on the phone to the farthest channel from your
wireless network. For example, change the phone to channel 1 and move your NB16WV-02 to channel 11. See your
phone’s user manual for detailed instructions.
If necessary, consider switching to a 900MHz or 5GHz cordless phone.
Choose the “Quietest” Channel for your Wireless Network
In locations where homes or offices are close together, such as apartment buildings or office complexes, there may be wireless
networks nearby that can conflict with your wireless network. Use the Site Survey capabilities found in the Wireless Utility of your
wireless adapter to locate any other wireless networks that are available (see your wireless adapter’s user manual), and switch
your Router and computers to a channel as far away from other networks as possible.
Experiment with more than one of the available channels, in order to find the clearest connection and avoid interference from
neighbouring cordless phones or other wireless devices.
www.netcommwireless.com
Ver 1.2
NetComm Wireless NB16WV-02 User Guide
12
Hardware installation
1.
Connect the power adapter to the Power socket on the back of the NB16WV-02.
2.
Plug the power adapter into the wall socket and switch on the power.
3.
Wait approximately 60 seconds for the NB16WV-02 to power up.
Connecting via a cable
1.
Connect the yellow Ethernet cable provided to one of the ports marked ‘LAN’ at the back of the NB16WV-02.
2.
Connect the other end of the yellow Ethernet cable to your computer.
3.
Wait approximately 30 seconds for the connection to establish.
4.
Open your Web browser, and enter http://192.168.20.1 into the address bar and press enter.
5.
Follow the steps to set up your NB16WV-02.
Connecting wirelessly
1.
Ensure Wi-Fi is enabled on your device (computer/laptop/Smartphone).
2.
Scan for wireless networks in your area and connect to the network name that matches the Wireless network name
configured on the NB16WV-02.
Note: Refer to the included Wireless Security Card for the default SSID and wireless security key of your NB16WV-02
3.
When prompted for your wireless security settings, enter the Wireless security key configured on the NB16WV-02.
4.
Wait approximately 30 seconds for the connection to establish.
5.
Open your Web browser, and enter http://192.168.20.1 into the address bar and press Enter.
6.
Follow the steps to set up your NB16WV-02.
Telephone Setup
1.
Insert the RJ-11-to-RJ-11 cable that comes delivered with your telephone into the FXS Phone Port (RJ-11) of the NB16WV02.
2.
Make sure the other end of the cable is plugged firmly into the RJ-11 port of your telephone.
3.
Follow the steps to setup your VoIP account details.
NetComm Wireless NB16WV-02 User Guide
13
www.netcommwireless.com
Ver 1.2
Web Based Configuration
Interface
First-time Setup Wizard
Please follow the steps below to configure your NB16WV-02 Wireless router via the web based configuration wizard.
Open your web browser (e.g. Internet Explorer/Firefox/Safari) and type http://192.168.20.1/ into the address bar at the top of
the window.
At the login screen, type admin in the username and password field, then click the Login button.
Note: admin is the default username and password for the unit.
1.
Click on Yes, let’s get started with the wizard.
The wizard assists you in configuring the router and entering the information required to setup your Internet connection.
www.netcommwireless.com
Ver 1.2
NetComm Wireless NB16WV-02 User Guide
14
2.
From the WAN Interface pull down menu, select the type of Internet connection you would like to use. You can select from:
ADSL
Mobile Broadband
WAN
ADSL
a.
Select the type of ADSL connection. You can select from:
PPP over ATM (or PPPoA)
PPP over Ethernet (or PPPoE)
b.
Enter the Username and Password as supplied by your Internet Service Provider.
c.
Enter the appropriate VCI and VPI as supplied by your Internet Service Provider.
d.
Click Next to continue.
NetComm Wireless NB16WV-02 User Guide
15
www.netcommwireless.com
Ver 1.2
Mobile Broadband
a.
Select your country and mobile broadband service provider from the list.
b.
Check that the APN displayed is correct as per the information provided by your mobile broadband provider.
c.
If your carrier requires you to log on to the network, enter the authentication criteria in the Username and Password
fields.
d.
If your SIM requires a PIN, enter it in the PIN and Confirm PIN fields.
e.
Click Next to continue.
WAN
Select the type of WAN connection:
Dynamic IP Address
a.
Enter the Host Name (Optional)
b.
Enter the MAC Address of your device which is registered with the ISP
Static IP Address
www.netcommwireless.com
Ver 1.2
NetComm Wireless NB16WV-02 User Guide
16
a.
Enter the Static IP Address.
b.
Enter the Static Subnet Mask.
c.
Enter the Static Gateway.
d.
Enter the Static Primary and Secondary DNS.
PPP over Ethernet (or PPPoE)
Enter the PPPoE Username and Password supplied by your service provider.
PPTP
a.
Enter the Server IP Address/Name.
b.
Enter the PPTP Account and PPTP Password.
L2TP
a.
Enter the Server IP Address/Name.
b.
Enter the PPTP Account and PPTP Password.
Click Next when you have entered the required details.
3.
If you want to change the 2.4GHz Wireless network settings, you can do so on this page. You can enable or disable the
Wireless network, select whether to broadcast your SSID or not and change the Wireless network name. Change the settings
as needed and click Next.
(If you wish to use the default settings, click Next)
4.
You can change the WiFi 2.4GHz security key if you wish by using the Security Key Type drop down list and then typing in a
new security key in the Security Key field. The Security key must be at least 8 characters long. Click Next to continue.
NetComm Wireless NB16WV-02 User Guide
17
www.netcommwireless.com
Ver 1.2
www.netcommwireless.com
Ver 1.2
NetComm Wireless NB16WV-02 User Guide
18
5.
If you want to change the 5GHz Wireless network settings, you can do so on this page. You can enable or disable the
Wireless network, select whether to broadcast your SSID or not and change the Wireless network name. Change the settings
as needed and click Next.
(If you wish to use the default settings, click Next)
6.
You can change the WiFi 5GHz security key if you wish by using the Security Key Type drop down list and then typing in a
new security key in the Security Key field. The Security key must be at least 8 characters long. Click Next to continue.
NetComm Wireless NB16WV-02 User Guide
19
www.netcommwireless.com
Ver 1.2
7.
If you want to change the system username or password, enter the new username in the Desired Username field and then
enter the new password into both the Desired Password and Retype Password fields and then click Next.
(If you do not wish to change the password, leave the fields blank and click Next).
8.
Confirm the setup information and click Finish if everything is correct. You can also click Back to go back and change any of
the previously configured settings.
When you click Finish, the wizard applies your settings and the Advanced Status view is displayed. Your Dual Band WiFi Modem
Router is ready to use.
www.netcommwireless.com
Ver 1.2
NetComm Wireless NB16WV-02 User Guide
20
Basic View
When you log in to the router, the Basic View is displayed. Basic View gives you the most important information at a glance.
Status
The Status tab displays the following information:
ADSL Line Status
ADSL Sync Speed
The current WAN IP Address
3G Status
3G Signal Strength
VoIP Service Status (If configured)
Number of clients connected on Wireless 2.4GHz
Number of clients connected on Wireless 5GHz
NetComm Wireless NB16WV-02 User Guide
21
www.netcommwireless.com
Ver 1.2
Wireless 2.4GHz
The wireless tab displays the following options for the 2.4GHz network:
Turn Wireless (WiFi) on or off
Turn SSID Broadcast on or off
Set the SSID (WiFi Network Name)
Set the Wireless Security Key
If you make any changes to the Wireless 2.4GHz configuration, Click the Save and apply the changes button to make these
changes active.
Wireless 5GHz
The wireless tab displays the following options for the 5GHz network:
Turn Wireless (WiFi) on or off
Turn SSID Broadcast on or off
Set the SSID (WiFi Network Name)
Set the Wireless Security Key
If you make any changes to the Wireless 5GHz configuration, Click the Save and apply the changes button to make these
changes active.
www.netcommwireless.com
Ver 1.2
NetComm Wireless NB16WV-02 User Guide
22
Mobile Broadband
The following configuration options are available on the Mobile Broadband tab:
Country
Service Provider
Network Name (APN)
SIM Status
PIN
Confirm PIN
To configure your 3G/4G (Mobile Broadband) connection, select the applicable Country and Service Provider. The Network Name
(APN) should be automatically filled with the correct APN. Please verify this with the information supplied by your 3G/4G provider.
The SIM Status will show if a PIN is required to use your SIM. If it is, enter the SIM PIN into the PIN and Confirm PIN fields.
If you make any changes to the 3G configuration, click the Save and apply the changes button to make these changes active.
Note: Saving any configuration changes on this page will make the Mobile Broadband connection the primary method of
connecting to the Internet and disable other connection types. To enable Mobile broadband as a secondary failover,
please configure Mobile Broadband in the Advanced View.
ADSL
The following configuration options are available on the ADSL tab:
Username
Password
Protocol
VPI Number
VCI Number
To configure your ADSL connection, enter the username and password as supplied by your ADSL service Provider.
Select the applicable protocol for your ADSL service. You can select from:
PPP over Ethernet (or PPPoE)
PPP over ATM (or PPPoA)
NetComm Wireless NB16WV-02 User Guide
23
www.netcommwireless.com
Ver 1.2
Enter the VPI Number (usually 8 for an ADSL service in Australia) and the VCI Number (usually 35 for an ADSL service in Australia)
as supplied by your ADSL service Provider.
If you make any changes to the ADSL configuration, click the Save and apply the changes button to make these changes active.
Note: Saving any configuration changes on this page will make the ADSL connection the primary method of connecting
to the Internet and disable other connection types.
www.netcommwireless.com
Ver 1.2
NetComm Wireless NB16WV-02 User Guide
24
Advanced Configuration
To access the advanced configuration options of your NB16WV-02, you need to log in to the web configuration and change to
Advanced view.
To do this, open your web browser (e.g. Internet Explorer/Firefox/Safari), type http://192.168.20.1/ into the address bar at the
top of the window and press the Enter key.
At the login screen, type admin in the Username and Password field and click the Login button.
Note: admin is the default username and password for the unit.
Click on the Switch to Advanced View link at the bottom of the page. The Advanced Status page is displayed.
Status
NetComm Wireless NB16WV-02 User Guide
25
www.netcommwireless.com
Ver 1.2
ITEM
DESCRIPTION
Wireless 2.4GHz Status
Wireless 2.4GHz mode
The status of the 2.4GHz wireless radio.
SSID
The SSID of the 2.4GHz wireless network.
Channel
The channel number in use by the 2.4GHz radio.
Security
The form of authentication in use on the router for the 2.4GHz wireless network. Side note
shows the encryption method used.
MAC Address
The unique identifier assigned to your 2.4GHz wireless interface.
Wireless 5GHz Status
Wireless 5GHz mode
The status of the 5GHz wireless radio.
SSID
The SSID of the 5GHz wireless network.
Channel
The channel number in use by the 5GHz radio.
Security
The form of authentication in use on the router for the 5GHz wireless network. Side note
shows the encryption method used.
MAC Address
The unique identifier assigned to your 5GHz wireless interface.
VoIP Status
VoIP
The registration status of the VoIP function. Side note indicates the interface that VoIP is
currently assigned to.
Statistics Information
Octets
The number of data bytes which have passed into and out of the router.
Unicast packets
The number of unicast packets which have passed into and out of the router.
Multicast packets
The number of multicast packets which have passed into and out of the router.
Network Setup
Network Setup
This page allows you to configure the ADSL, Mobile Broadband and Ethernet WAN (Wide Area Network) connection settings on
the NB16WV-02.
ADSL
Ethernet over ATM (RFC1483 bridged) with NAT
www.netcommwireless.com
Ver 1.2
NetComm Wireless NB16WV-02 User Guide
26
OPTION
DEFINITION
WAN Interface
The interface to configure. When ADSL is selected you may select a permanent virtual circuit (PVC) from 0 to 7.
WAN Type
The type of ADSL connection to use.
Remote Host for keep alive
A host name to use for the keep alive function. This host will be used to send a ping request in order to keep the
connection alive.
IP Mode
Select to use either a static or dynamically assigned IP address for your connection. When selecting to utilise a static IP
address, you will also need to enter the WAN IP Address, WAN Subnet Mask and WAN Default gateway in use for the
connection
(Refer to your ISP for more information).
Host Name
ISP Registered MAC Address
Set the hostname for your connection
(Optional - Refer to your ISP for more information).
You can change the WAN port MAC address if needed to clone your 3G modem (Optional - Refer to your ISP for more
information).
NAT
This option enables or disables "Network Address Translation" for this connection type.
Data Encapsulation
Select the Data Encapsulation required by your ISP
(Refer to your ISP for more information).
VPI Number
VCI Number
Enter the VPI provided by your ISP
(This will usually be 8 for Australia or 0 for New Zealand)
Enter the VCI provided by your ISP
(This will usually be 35 for Australia or 100 for New Zealand)
Schedule Type
Select the data schedule type required by your ISP
(Refer to your ISP for more information).
Multicast
Allows you to select the method of multicast or disable it.
IGMP Snooping
Allows you to enable or disable IGMP Snooping. IGMP Snooping configures the router to listen to IGMP conversations
between hosts and routers and maintain a map of the links that need IP multicast streams.
VLAN TAG
VLAN tagging is primarily used in virtual networks which span over multiple switches. VLAN tagging involves the router
inserting a VLAN ID into a packet header in order to identify which CLAN the packet belongs to. You may enable VLAN
tagging and specify the ID with a value between 1 and 4094.
IP over ATM (RFC1483 routed)
NetComm Wireless NB16WV-02 User Guide
27
www.netcommwireless.com
Ver 1.2
OPTION
DEFINITION
WAN Interface
The interface to configure. When ADSL is selected you may select a permanent virtual circuit (PVC) from 0 to 7.
WAN Type
The type of ADSL connection to use.
Remote Host for keep alive
A host name to use for the keep alive function. This host will be used to send a ping request in order to keep the
connection alive.
IP Mode
Select to use either a static or dynamically assigned IP address for your connection. When selecting to utilise a static IP
address, you will also need to enter the WAN IP Address, WAN Subnet Mask and WAN Default gateway in use for the
connection
(Refer to your ISP for more information).
Host Name
ISP Registered MAC Address
Set the hostname for your connection
(Optional - Refer to your ISP for more information).
You can change the WAN port MAC address if needed to clone your 3G modem (Optional - Refer to your ISP for more
information).
NAT
This option enables or disables "Network Address Translation" for this connection type.
Data Encapsulation
Select the Data Encapsulation required by your ISP
(Refer to your ISP for more information).
VPI Number
VCI Number
Enter the VPI provided by your ISP
(This will usually be 8 for Australia or 0 for New Zealand)
Enter the VCI provided by your ISP
(This will usually be 35 for Australia or 100 for New Zealand)
Schedule Type
Select the data schedule type required by your ISP
(Refer to your ISP for more information).
Multicast
Allows you to select the method of multicast or disable it.
IGMP Snooping
Allows you to enable or disable IGMP Snooping. IGMP Snooping configures the router to listen to IGMP conversations
between hosts and routers and maintain a map of the links that need IP multicast streams.
VLAN TAG
VLAN tagging is primarily used in virtual networks which span over multiple switches. VLAN tagging involves the router
inserting a VLAN ID into a packet header in order to identify which CLAN the packet belongs to. You may enable VLAN
tagging and specify the ID with a value between 1 and 4094.
PPP over Ethernet
www.netcommwireless.com
Ver 1.2
NetComm Wireless NB16WV-02 User Guide
28
OPTION
DEFINITION
WAN Interface
The interface to configure. When ADSL is selected you may select a permanent virtual circuit (PVC) from 0 to 7.
WAN Type
The type of ADSL connection to use.
Remote Host for keep alive
A host name to use for the keep alive function. This host will be used to send a ping request in order to keep the
connection alive.
IPv6 Dualstack
Enables IPv6 Dual stack which allows IPv4 and IPv6 to run side-by-side without encapsulating one protocol within the
other.
Username
The account name given to you by your ISP.
Password
The password given to you by your ISP.
(For security, this field appears blank. If you don't want to change the password, leave it empty)
Primary DNS
This feature allows you to manually assign a Primary DNS Server
(Optional - Refer to your ISP for more information).
Secondary DNS
This feature allows you to manually assign a Secondary DNS Server
(Optional - Refer to your ISP for more information).
Service Name
Enter the service name if your ISP requires it
(Optional - Refer to your ISP for more information).
Assigned IP Address
Enter the IP address assigned to your service. This is usually left blank.
MTU
The default MTU value is 0 (auto). It is set automatically when you connect.
NAT
This option enables or disables "Network Address Translation" for this connection type.
Data Encapsulation
Select the Data Encapsulation required by your ISP
(Refer to your ISP for more information).
VPI Number
VCI Number
Enter the VPI provided by your ISP
(This will usually be 8 for Australia or 0 for New Zealand)
Enter the VCI provided by your ISP
(This will usually be 35 for Australia or 100 for New Zealand)
Schedule Type
Select the data schedule type required by your ISP
(Refer to your ISP for more information).
Multicast
Allows you to select the method of multicast or disable it.
IGMP Snooping
Allows you to enable or disable IGMP Snooping. IGMP Snooping configures the router to listen to IGMP conversations
between hosts and routers and maintain a map of the links that need IP multicast streams.
VLAN TAG
VLAN tagging is primarily used in virtual networks which span over multiple switches. VLAN tagging involves the router
inserting a VLAN ID into a packet header in order to identify which CLAN the packet belongs to. You may enable VLAN
tagging and specify the ID with a value between 1 and 4094.
NetComm Wireless NB16WV-02 User Guide
29
www.netcommwireless.com
Ver 1.2
PPP over ATM
www.netcommwireless.com
Ver 1.2
NetComm Wireless NB16WV-02 User Guide
30
OPTION
DEFINITION
WAN Interface
The interface to configure. When ADSL is selected you may select a permanent virtual circuit (PVC) from 0 to 7.
WAN Type
The type of ADSL connection to use.
Remote Host for keep alive
A host name to use for the keep alive function. This host will be used to send a ping request in order to keep the
connection alive.
IPv6 Dualstack
Enables IPv6 Dual stack which allows IPv4 and IPv6 to run side-by-side without encapsulating one protocol within the
other.
Username
The account name given to you by your ISP.
Password
The password given to you by your ISP.
(For security, this field appears blank. If you don't want to change the password, leave it empty)
Primary DNS
This feature allows you to manually assign a Primary DNS Server
(Optional - Refer to your ISP for more information).
Secondary DNS
This feature allows you to manually assign a Secondary DNS Server
(Optional - Refer to your ISP for more information).
Service Name
Enter the service name if your ISP requires it
(Optional - Refer to your ISP for more information).
Assigned IP Address
Enter the IP address assigned to your service. This is usually left blank.
MTU
The default MTU value is 0 (auto). It is set automatically when you connect.
NAT
This option enables or disables "Network Address Translation" for this connection type.
Data Encapsulation
Select the Data Encapsulation required by your ISP
(Refer to your ISP for more information).
VPI Number
VCI Number
Enter the VPI provided by your ISP
(This will usually be 8 for Australia or 0 for New Zealand)
Enter the VCI provided by your ISP
(This will usually be 35 for Australia or 100 for New Zealand)
Schedule Type
Select the data schedule type required by your ISP
(Refer to your ISP for more information).
Multicast
Allows you to select the method of multicast or disable it.
IGMP Snooping
Allows you to enable or disable IGMP Snooping. IGMP Snooping configures the router to listen to IGMP conversations
between hosts and routers and maintain a map of the links that need IP multicast streams.
VLAN TAG
VLAN tagging is primarily used in virtual networks which span over multiple switches. VLAN tagging involves the router
inserting a VLAN ID into a packet header in order to identify which CLAN the packet belongs to. You may enable VLAN
tagging and specify the ID with a value between 1 and 4094.
RFC 1483 Bridged
NetComm Wireless NB16WV-02 User Guide
31
www.netcommwireless.com
Ver 1.2
Mobile Broadband
OPTION
DEFINITION
WAN Interface
The interface to configure. When Mobile Broadband is selected, you may also configure whether the connection is active
or inactive.
Country
Select your country from the list. This will shorten the APN list to those in your selected country.
Service Provider
Select your mobile broadband service provider from the list. This will then enable you to select the correct APN for the
mobile broadband service in use.
APN
Enter the APN for your mobile broadband service. This should be automatically filled in after selecting your country and
3G provider name. If the wrong APN is shown, enter the correct APN for your mobile broadband service
PIN Code
Enter the Pin Code for your SIM card (if required).
Dial Number
This number is required to connect to your mobile broadband service.
(Unless advised otherwise by NetComm Wireless Technical Support, this setting should not be changed)
Username
The username provided by your mobile broadband service provider to enable access to your mobile broadband service.
Password
The password provided by your mobile broadband service provider to enable access to your mobile broadband service.
Authentication Type
Choose the appropriate authentication type for your mobile broadband service.
Primary DNS
Manually assign a Primary DNS Server.
Secondary DNS
Manually assign a Secondary DNS Server.
Allowed Connection Time
This setting enables you to configure when the mobile broadband connection may be active. By default it is set to
“Always”. If you select “By Schedule” you can select a schedule rule or create a new one. See the next page for details
on creating a schedule rule.
MTU
The default MTU value is 0 (auto). It is set automatically when you connect.
Keep Alive
There are three keep alive options to select from:

Disable: Disable the keep alive function.

LCP Echo Request: The NB16WV-02 will automatically verify the connection is active. Set the interval
and Max number of failures to determine when the connection is up or down.

Ping Remote Host: The NB16WV-02 will ping the chosen host IP to verify the connection is active. Set
the host IP address and the interval between ping tests.
Multicast
Allows you to select the method of multicast or disable it.
IGMP Snooping
Allows you to enable or disable IGMP Snooping. IGMP Snooping configures the router to listen to IGMP conversations
between hosts and routers and maintain a map of the links that need IP multicast streams.
Creating a connection schedule for Mobile Broadband
www.netcommwireless.com
Ver 1.2
NetComm Wireless NB16WV-02 User Guide
32
To create a new schedule rule:
1.
Select the By Schedule option then click the Add New Schedule button.
The schedule creation window appears.
2.
Enter a name for the rule in the Name of Rule 1 field.
3.
Using the Policy drop down list, select whether the connection should be Active or Inactive except for the selected days and
hours below. This is the default behaviour of the connection for the times not specified.
4.
In the Week Day column, use the drop down lists to select a day of the week for which to create a schedule and in the Start
Time (hh:mm) and End Time (hh:mm) fields, enter the time in 24 hour format for the schedule to apply.
5.
Repeat step 4 for each day a rule is to be created.
6.
Click the Save button.
NetComm Wireless NB16WV-02 User Guide
33
www.netcommwireless.com
Ver 1.2
Ethernet WAN
WAN Type: You can select from the following WAN types:Dynamic IP
Static IP
PPP over Ethernet
PPTP
L2TP
Dynamic IP Address
OPTION
DEFINITION
WAN Interface
The interface to configure. When Mobile Broadband is selected, you may also configure whether the connection is active
or inactive.
WAN Type
Use the drop down list to select the type of WAN connection you want to use.
Remote Host for keep alive
A host name to use for the keep alive function. This host will be used to send a ping request in order to keep the
connection alive.
Host Name
Set the hostname for your connection
(Optional - Refer to your ISP for more information).
ISP Registered MAC Address
You can change the WAN port MAC address if needed to clone your 3G modem
(Optional - Refer to your ISP for more information).
NAT
This option enables or disables "Network Address Translation" for this connection type.
Multicast
Allows you to select the method of multicast or disable it.
IGMP Snooping
Allows you to enable or disable IGMP Snooping. IGMP Snooping configures the router to listen to IGMP conversations
between hosts and routers and maintain a map of the links that need IP multicast streams.
VLAN TAG
VLAN tagging is primarily used in virtual networks which span over multiple switches. VLAN tagging involves the router
inserting a VLAN ID into a packet header in order to identify which CLAN the packet belongs to. You may enable VLAN
tagging and specify the ID with a value between 1 and 4094.
www.netcommwireless.com
Ver 1.2
NetComm Wireless NB16WV-02 User Guide
34
Static IP Address
OPTION
DEFINITION
WAN Interface
The interface to configure. When Mobile Broadband is selected, you may also configure whether the connection is active
or inactive.
WAN Type
Use the drop down list to select the type of WAN connection you want to use.
Remote Host for keep alive
A host name to use for the keep alive function. This host will be used to send a ping request in order to keep the
connection alive.
WAN IP Address
The static IP address assigned to you by your internet service provider.
WAN Subnet Mask
The subnet mask of the IP address assigned to you by your internet service provider.
WAN Gateway
The WAN Gateway provided to you by your internet service provider.
Primary DNS
This feature allows you to manually assign a Primary DNS Server
(Optional - Refer to your ISP for more information).
Secondary DNS
This feature allows you to manually assign a Secondary DNS Server (Optional - Refer to your ISP for more information).
NAT
This option enables or disables "Network Address Translation" for this connection type.
Multicast
Allows you to select the method of multicast or disable it.
IGMP Snooping
Allows you to enable or disable IGMP Snooping. IGMP Snooping configures the router to listen to IGMP conversations
between hosts and routers and maintain a map of the links that need IP multicast streams.
VLAN TAG
VLAN tagging is primarily used in virtual networks which span over multiple switches. VLAN tagging involves the router
inserting a VLAN ID into a packet header in order to identify which CLAN the packet belongs to. You may enable VLAN
tagging and specify the ID with a value between 1 and 4094.
NetComm Wireless NB16WV-02 User Guide
35
www.netcommwireless.com
Ver 1.2
PPP over Ethernet
OPTION
DEFINITION
WAN Interface
The interface to configure. When Mobile Broadband is selected, you may also configure whether the connection is active
or inactive.
WAN Type
Use the drop down list to select the type of WAN connection you want to use.
Remote Host for keep alive
A host name to use for the keep alive function. This host will be used to send a ping request in order to keep the
connection alive.
Username
The account name given to you by your ISP.
Password
The password given to you by your ISP.
Primary DNS
This feature allows you to manually assign a Primary DNS Server
(Optional - Refer to your ISP for more information).
Secondary DNS
Service Name
This feature allows you to manually assign a Secondary DNS Server (Optional - Refer to your ISP for more information).
Enter the service name if your ISP requires it
(Optional - Refer to your ISP for more information).
Assigned IP Address
Enter the IP address assigned to your service. This is usually left blank.
MTU
The default MTU value is 0 (auto). It is set automatically when you connect.
NAT
This option enables or disables "Network Address Translation" for this connection type
Multicast
Allows you to select the method of multicast or disable it.
IGMP Snooping
Allows you to enable or disable IGMP Snooping. IGMP Snooping configures the router to listen to IGMP conversations
between hosts and routers and maintain a map of the links that need IP multicast streams.
VLAN TAG
VLAN tagging is primarily used in virtual networks which span over multiple switches. VLAN tagging involves the router
inserting a VLAN ID into a packet header in order to identify which CLAN the packet belongs to. You may enable VLAN
tagging and specify the ID with a value between 1 and 4094.
www.netcommwireless.com
Ver 1.2
NetComm Wireless NB16WV-02 User Guide
36
PPTP
OPTION
DEFINITION
WAN Interface
The interface to configure. When Mobile Broadband is selected, you may also configure whether the connection is active
or inactive.
WAN Type
Use the drop down list to select the type of WAN connection you want to use.
Remote Host for keep alive
A host name to use for the keep alive function. This host will be used to send a ping request in order to keep the
connection alive.
IP Mode
Select to use either a static or dynamically assigned IP address for your connection. When selecting to utilise a static IP
address, you will also need to enter the PPTP IP Address, PPTP Subnet Mask and PPTP Default gateway in use for the
connection
(Refer to your PPTP administrator for more information).
Server IP Address/Name
Enter the PPTP server name or IP Address.
PPTP Account
Enter the PPTP username supplied by your PPTP administrator.
PPTP Password
Enter the PPTP password supplied by your PPTP administrator.
Connection ID
Enter an Optional name to identify the PPTP connection.
MTU
The default MTU value is 0 (auto). It is set automatically when you connect.
MPPE
Select to enable or disable the MPPE security extensions for the PPTP connection.
Multicast
Allows you to select the method of multicast or disable it.
IGMP Snooping
Allows you to enable or disable IGMP Snooping. IGMP Snooping configures the router to listen to IGMP conversations
between hosts and routers and maintain a map of the links that need IP multicast streams.
VLAN TAG
VLAN tagging is primarily used in virtual networks which span over multiple switches. VLAN tagging involves the router
inserting a VLAN ID into a packet header in order to identify which CLAN the packet belongs to. You may enable VLAN
tagging and specify the ID with a value between 1 and 4094.
NetComm Wireless NB16WV-02 User Guide
37
www.netcommwireless.com
Ver 1.2
L2TP
OPTION
DEFINITION
WAN Interface
The interface to configure. When Mobile Broadband is selected, you may also configure whether the connection is active
or inactive.
WAN Type
Use the drop down list to select the type of WAN connection you want to use.
Remote Host for keep alive
A host name to use for the keep alive function. This host will be used to send a ping request in order to keep the
connection alive.
IP Mode
Select to use either a static or dynamically assigned IP address for your connection. When selecting to utilise a static IP
address, you will also need to enter the L2TP IP Address, L2TP Subnet Mask and L2TP Default gateway in use for the
connection
(Refer to your PPTP administrator for more information).
Server IP Address/Name
Enter the L2TP server name or IP Address.
L2TP Account
Enter the L2TP username supplied by your L2TP administrator.
L2TP Password
Enter the L2TP password supplied by your L2TP administrator.
MTU
The default MTU value is 0 (auto). It is set automatically when you connect.
MPPE
Select to enable or disable the MPPE security extensions for the L2TP connection.
Multicast
Allows you to select the method of multicast or disable it.
IGMP Snooping
Allows you to enable or disable IGMP Snooping. IGMP Snooping configures the router to listen to IGMP conversations
between hosts and routers and maintain a map of the links that need IP multicast streams.
VLAN TAG
VLAN tagging is primarily used in virtual networks which span over multiple switches. VLAN tagging involves the router
inserting a VLAN ID into a packet header in order to identify which CLAN the packet belongs to. You may enable VLAN
tagging and specify the ID with a value between 1 and 4094.
www.netcommwireless.com
Ver 1.2
NetComm Wireless NB16WV-02 User Guide
38
DHCP Server
This page allows you to change the Dynamic Host Configuration Protocol (DHCP) server settings on the NB16WV-02. The DHCP
Server enables computers or devices connecting to the NB16WV-02 to automatically obtain their network configuration settings.
By default, the DHCP server is enabled.
The LAN IP Address and Subnet Mask fields offer the ability to configure the IP address of the router locally and the subnet mask.
OPTION
DHCP Server
LAN IP Address
DEFINITION
Enable or disable the DHCP server.
The local IP address of the NB16WV-02.
(The computers on your network must use this IP address as their Default Gateway. You can change it if necessary.)
Subnet Mask
Enter the subnet mask for use on the local network. This would usually be set to 255.255.255.0.
IP Pool Starting/Ending Address
Whenever there is a request, the DHCP server will automatically allocate an unused IP address from the IP address pool
to the requesting computer. You must specify the starting / ending address of the IP address pool
Lease Time
Length of the DHCP lease time
Domain Name
Optional, this information will be passed to the client
Primary DNS
Optional, this information will be passed to the client
Secondary DNS
Optional, this information will be passed to the client
Primary WINS
Optional, this information will be passed to the client
Secondary WINS
Optional, this information will be passed to the client
Gateway
Optional, this information will be passed to the client
When you have finished configuring the DHCP Server settings, click Save to save your settings. If you want to cancel any changes
you have made before saving them, click the Undo button.
Use the Clients List button to check the DHCP client list. The Fixed Mapping button allows you to map a specific IP address to a
specific MAC address. The following pages describe these features in more detail.
NetComm Wireless NB16WV-02 User Guide
39
www.netcommwireless.com
Ver 1.2
DHCP Client List
This is the list of currently connected devices using DHCP.
If you wish to assign permanent IP address for a particular DHCP client (or device), select the appropriate DHCP client by clicking
in the "Select" box, and click on “Add to Fix Map Table”. This will ensure the clients current IP address is reserved.
DHCP Fixed Mapping
DHCP Fixed Mapping allows you to reserve a specific IP address for a specific device.
The DHCP Server will reserve a specific IP for a device based on that device’s unique MAC address.
You can enter a new fixed mapping by entering the MAC address of the device and the IP address you wish to allocate to it.
To locate your device’s unique MAC address, please refer to your device’s user manual.
Select the Enable checkbox to activate the DHCP fixed mapping entry.
www.netcommwireless.com
Ver 1.2
NetComm Wireless NB16WV-02 User Guide
40
Wireless 2.4GHz
The Wireless 2.4GHz page allows you to configure the options related to the 2.4GHz wireless network of the router.
OPTION
DEFINITION
Wireless Module (2.4GHz)
Select to enable or disable the 2.4GHz Wireless network function of the NB16WV-02.
Network ID (SSID)
Network ID is used for identifying the Wireless LAN (WLAN). Client stations can roam freely over this product and other
Access Points that have the same Network ID.
(Please refer to the included Wireless Security Card insert for your default SSID)
SSID Broadcast
The router will broadcast the SSID so that wireless clients can find the wireless network.
Channel
The wireless radio channel in use by your network.
Wireless Mode
Choose B/G Mixed, B only, G only, and N only, G/N Mixed or B/G/N mixed.
(The factory default setting is B/G/N mixed)
Authentication
Authentication
You may select from the following authentication types to secure your wireless network:

Open

Shared

Auto

WPA

WPA-PSK

WPA2

WPA2-PSK

WPA/WPA2

WPA-PSK/WPA2-PSK.
WPA-PSK/WPA2-PSK is a newer type of security. This type of security gives a more secure network compared to WEP. Use
TKIP Encryption Type for WPA-PSK and AES for WPA2-PSK.
Please enter the key in the “Pre-share Key”. The key needs to be more than 8 characters and less than 63 characters. It can
be any combination of letters and numbers.
(Please refer to the included Wireless Security Card insert for your default WPA-PSK2 key)
802.1X
When Authentication is set to Open, you can enable 802.1X which enables Extensible Authentication Protocol (EAP) over
wired or wireless networks.
Encryption
Select the type of encryption for your network. These options vary depending on the type of Authentication selected.
Note: The configuration for WPA-PSK and WPA2-PSK is identical. Additionally, disabling SSID broadcast will not
increase your WiFi network’s security. Hidden SSID networks can be unmasked with specific network tools.
After configuring wireless security, you also need to configure your wireless adapter to use the same security settings before you
can connect wirelessly. Not all wireless adapters support WPA-PSK/WPA2-PSK/WPA/WPA2 security. Please refer to your
wireless adapter user guide for more information. (Many drivers for Window XP wireless network adapters do not support WPA2.)
It is strongly recommended that you set up wireless security such as WPA2-PSK (when the wireless client supports WPA2) in
order to secure your network.
Click Save to save these settings or click Undo to cancel.
NetComm Wireless NB16WV-02 User Guide
41
www.netcommwireless.com
Ver 1.2
Wireless 5GHz
The Wireless 5GHz page allows you to configure the options related to the 5GHz wireless network of the router.
OPTION
DEFINITION
Wireless Module (5GHz)
Select to enable or disable the 5GHz Wireless network function of the NB16WV-02.
Network ID (SSID)
Network ID is used for identifying the Wireless LAN (WLAN). Client stations can roam freely over this product and other
Access Points that have the same Network ID.
(Please refer to the included Wireless Security Card insert for your default SSID)
SSID Broadcast
The router will broadcast the SSID so that wireless clients can find the wireless network.
Channel
The wireless radio channel in use by your network.
Wireless Mode
Authentication
Choose A only, N only or A/N Mixed.
(The factory default setting is A/N Mixed)
You may select from the following authentication types to secure your wireless network:

Open

Shared

Auto

WPA

WPA-PSK

WPA2

WPA2-PSK

WPA/WPA2

WPA-PSK/WPA2-PSK.
WPA-PSK/WPA2-PSK is a newer type of security. This type of security gives a more secure network compared to WEP. Use
TKIP Encryption Type for WPA-PSK and AES for WPA2-PSK.
Please enter the key in the “Pre-share Key”. The key needs to be more than 8 characters and less than 63 characters. It can
be any combination of letters and numbers.
(Please refer to the included Wireless Security Card insert for your default WPA-PSK2 key)
802.1X
When Authentication is set to Open, you can enable 802.1X which enables Extensible Authentication Protocol (EAP) over
wired or wireless networks.
Encryption
Select the type of encryption for your network. These options vary depending on the type of Authentication selected.
Note: Disabling SSID broadcast will not increase your WiFi network’s security. Hidden SSID networks can be unmasked
with specific network tools.
www.netcommwireless.com
Ver 1.2
NetComm Wireless NB16WV-02 User Guide
42
Change Password
This page allows you to change the NB16WV-02 web configuration password.
Type in the old password (the factory default username and password is admin) and then type in the new password.
Re-enter the new password in the Reconfirm field and click Save.
We recommend that you change your router’s username and password for security reasons. You should record your new
username and password for future reference. In the case that you forget your username or password, you can restore the router
to the factory default settings via the reset button. This will restore the username and password to “admin”, however all
preconfigured settings will be lost.
NetComm Wireless NB16WV-02 User Guide
43
www.netcommwireless.com
Ver 1.2
Forwarding Rules
The Forwarding Rules page allows you to configure the port forwarding management on the router. Click on any of the menu
items on the left to access the respective settings page.
Forwarding rules are a necessary feature as by default NAT (Network Address Translation) will automatically block incoming traffic
from the Internet to the LAN unless a specific port mapping exists in the NAT translation table. Because of this, NAT provides a
level of protection for computers that are connected to your LAN.
However this also creates a connectivity problem when you want to make LAN resources available to Internet clients. For
example, to play network games or host network applications.
There are three ways to work around NAT and to enable certain LAN resources available from the Internet:
Port Forwarding
Port Triggering
DMZ Host
Port Forwarding
A virtual server is defined as a Service Port, and all requests to this port will be redirected to the computer specified by the Server
IP.
Port Forwarding can also work with Scheduling Rules, and give you more flexibility on Access control.
Note: For further instructions on scheduling rules, please refer to the “Scheduling” section later in this guide
www.netcommwireless.com
Ver 1.2
NetComm Wireless NB16WV-02 User Guide
44
For example, if you have an FTP server (the default port is 21 using TCP for FTP) at 192.168.1.10, a Web server (the port is 80
and 81) and an Authentication server (port 2008) at 192.168.20.40, and a VPN server (the default port is 1723 via UDP for PPTP
VPN) at 192.168.20.60, then you would need to specify the following virtual server mappings:
Note: At any given time, only one IP address can be bound to a particular Service Port. Port range can be entered by
separating the first and last port by a colon. (e.g. for port 8080 to port 8090 inclusive, enter 8080:8090)
ID
EXTERNAL PORT
1
21
2
SERVER IP
INTERNAL PORT
PROTOCOL
ENABLE
USE RULE#
192.168.1.10
21
TCP

(0) Always
80:81
192.168.20.40
80:81
Both

(0) Always
3
2008
192.168.20.40
2008
TCP

(0) Always
3
1723
192.168.20.60
1723
UDP

(0) Always
Click Save to save the settings or Undo to cancel.
NetComm Wireless NB16WV-02 User Guide
45
www.netcommwireless.com
Ver 1.2
Port Triggering
Some applications like online games, video conferencing and Internet telephony require multiple connections to the internet. As
such, these applications cannot work with a pure NAT router such as the NB16WV-02.
The Port Triggering feature allows some of these applications to work with this router.
Note: Please check if your application is compatible with port triggering first. If this fails to make the application work, try
to configure that computer as the DMZ host instead. Each port can only be used by 1 host machine at a time. If the port
is occupied by an existing host, port triggering/forwarding/DMZ for that port will not work.
(For further instructions on setting up a DMZ host, please refer to the “Miscellaneous” section below)
OPTION
DEFINITION
Trigger
The outbound port number that will be triggered by the application.
Incoming Ports
When the trigger packet is detected, the inbound packets sent to the specified port numbers will be allowed to pass through the
firewall to the triggering host.
Enable
Select to enable or disable the configured special application entry.
Port triggering opens an incoming port when your computer is using a specified outgoing port for specific traffic.
The NB16WV-02 also provides predefined settings for some popular applications.
To use the predefined settings, select your application from the “Popular applications” drop down list, select an unused ID from
the list and then click Copy to. The predefined settings will then be added to the list.
Click Save to save the settings or Undo to cancel.
www.netcommwireless.com
Ver 1.2
NetComm Wireless NB16WV-02 User Guide
46
Miscellaneous
A Demilitarized Zone (DMZ) Host is a computer without the protection of firewall. It allows that particular computer to be exposed
to unrestricted 2-way communication to the internet. It is mostly used for Internet games, Video conferencing, Internet telephony
and other special applications.
Universal Plug and Play (UPnP) allows UpnP enabled host computers to automatically edit port mapping allowing NAT traversal for
the host’s requesting applications.
To enable DMZ, enter the IP address of the computer you want to be live on the internet and select the Enable option.
Note: This feature should be used only when required as it exposes the selected machine to the greater Internet without
security.
If ports are used in port forwarding/triggering, traffic through these ports will be directed to the port forwarding/triggering
host PC, not to the DMZ host.
OPTION
DEFINITION
DMZ Mode
Select from Single Mode or Multi Mode. Single Mode uses the currently active connection type for the DMZ host while Multi Mode
allows you to specify which connection type should be placed in the DMZ.
IP Address of DMZ Host
Enter the IP address of the computer you wish to put in the DMZ.
UPnP Setting
The device supports UPnP. If enabled, UPnP capable LAN clients can automatically edit port mapping entries for its own
applications.
Click Save to save the settings or Undo to cancel.
NetComm Wireless NB16WV-02 User Guide
47
www.netcommwireless.com
Ver 1.2
Security Settings
The Security Settings page allows you to configure the security management on the router such as Packet filters and MAC
Control. The following pages describe the various security options available
Status
The Status page lists any currently configured filtering for the Outbound, Inbound and Domain filters.
www.netcommwireless.com
Ver 1.2
NetComm Wireless NB16WV-02 User Guide
48
Packet Filters
The Packet Filter enables you to control what packets are allowed to pass through the router. There are two types of packet filter,
Outbound Packet Filter which applies to all outbound packets and the Inbound Packet Filter which only applies to packets that are
destined for a LAN clients only.
Note: To ensure the filter is applied to the correct PC, you must first assign a fixed IP address to the intended LAN clients.
Please refer to DHCP Fixed Mapping for instructions. For further instructions on setting up MAC Level Filtering, please
refer to the “MAC Control” section below
Outbound Filter:
To enable an Outbound Filter, tick the Enable tick box at the top of the page.
There are two types of filtering policies:
Allow all data traffic to pass except those that match the specified rules.
Deny all data traffic to pass except those that match the specified rules.
You can specify up to 48 filtering rules for each direction (Inbound or Outbound). For each rule you will need to define the
following:
Source IP address
Source port
Destination IP address
Destination port
Protocol: TCP or UDP or both.
Use Schedule Rule#
For source or destination IP address, you can define a single IP address (192.168.1.1) or a range of IP addresses (192.168.1.100192.168.20.200). Leaving these fields empty implies all IP addresses are matched.
For source or destination port, you can also define a single port (80) or a range of ports (1000-1999). Use the prefix "T" or "U" to
specify either the TCP or UDP protocol e.g. T80, U53, U2000-2999. No prefix indicates both
TCP and UDP are defined. Leaving this field empty implies all ports are matched.
The Packet Filter also works with Scheduling Rules, and gives you more flexibility on Access control.
Note: For further instructions on scheduling rules, please refer to the “Scheduling” section later in this guide
Click Save to save the settings or Undo to cancel. Inbound Filter
To access the Inbound Packet Filter page, click on the Inbound Filter button on the bottom of the Outbound Filter page. All the
settings on this page are the same as those for the Outbound Filter shown on the previous page.
NetComm Wireless NB16WV-02 User Guide
49
www.netcommwireless.com
Ver 1.2
Click Save to save the settings or Undo to cancel.
www.netcommwireless.com
Ver 1.2
NetComm Wireless NB16WV-02 User Guide
50
Domain Filters
Domain Filters enable you to prevent users from accessing specific domain addresses.
To enable the Domain Filter, select the “Enable” tick box at the top of the page.
OPTION
DEFINITION
Domain Filter
Select to enable or disable domain filtering.
Log DNS Query
Enable this if you want to log when someone accesses filtered URLs.
Privilege IP Addresses Range
Set a group of computers that has unrestricted access to the internet.
Note: To enable a privileged IP address range, please first assign DHCP fixed mapping to the intended computer.
To set a Domain Filter, you need to specify the following:
OPTION
DEFINITION
Domain Suffix
Please type the suffix of the URL that needs to be restricted. For example, ".com", "xxx.com".
Action
The router action that you want when someone is accessing a URL that matches the specified domain suffix. Select Drop to
block the access and/or select Log to log this access.
Enable
Select to enable the rule.
Click Save to save the settings or Undo to cancel.
NetComm Wireless NB16WV-02 User Guide
51
www.netcommwireless.com
Ver 1.2
URL Blocking
URL Blocking blocks LAN computers from connecting to a pre-defined website. The major difference between the Domain Filter
and URL Blocking is that Domain Filtering requires you to input a suffix (e.g. xxx.com, yyy.net) while URL Blocking only requires
you to input a keyword.
To enable URL Blocking, select the Enable option at the top of the page.
To set a URL Blocking rule, you need to specify the following:
OPTION
DEFINITION
URL
If any part of the Website’s URL matches the pre-defined word then the connection will be blocked. For example, you can use
pre-defined word "sex" to block all websites if their URLs contain the pre-defined word "sex".
Enable
Tick to enable the rule.
Click Save to save the settings or Undo to cancel.
www.netcommwireless.com
Ver 1.2
NetComm Wireless NB16WV-02 User Guide
52
MAC Control (Access Control List)
MAC Control allows you to modify access rights for different users and restrict specific MAC address from associating with your
NB16WV-02.
To enable MAC Address Control, select the Enable option at the top of the page.
Two types of MAC Control are available:
OPTION
DEFINITION
Connection control (C column)
Use this to control which clients (wired and wireless) can connect to the unit. If a client is denied access to connect to this
device, it means the client cannot access the Internet or any other network resource/host. Choose to allow or deny clients
with MAC addresses that are not in the list to connect to this device.
Association control (A column)
Check Association Control to control which wireless client can associate with the unit. If a client is denied access to
associate with the unit, it means the client cannot send or receive any data via this device’s WiFi. Choose to allow or deny
the clients with MAC addresses that are not in the list to associate to the wireless LAN.
Note: Click the "Next Page" or the "Previous Page" buttons to see the entire list.
Note: The Media Access Control (MAC) address control list does not provide absolute control/security, MAC addresses
can be changed from factory assigned value with certain tools, allowing impersonation of a specific network device. Also
known as MAC spoofing.
Click Save to save the settings or Undo to cancel.
NetComm Wireless NB16WV-02 User Guide
53
www.netcommwireless.com
Ver 1.2
Miscellaneous
This page allows you to change various security settings on the unit.
OPTION
DEFINITION
Administrator Time-out
The period of time with no activity in the web configuration page to logout automatically, untick to disable this feature.
Remote Administrator
Host/Subnet:Port
Normally only Intranet users can browse the built-in web pages to perform administration tasks. This feature enables you
to perform administration tasks from a remote host. If this feature is enabled, only the specified IP address can perform
remote administration.
Discard PING from WAN side
When this feature is enabled, your router will not respond to ping requests from remote hosts.
DoS Attack Detection
When this feature is enabled, the router will detect and log where the DoS attack comes from on the Internet.
Keep WAN in stealth mode
When this feature is enabled, the router will not respond to port scans, making it less susceptible to discovery and
attacks.
Note: If the specified IP address is 0.0.0.0, any host can connect to the router to perform administration tasks. You can
also use a subnet mask (/nn) to specify a group of trusted IP addresses for example, "10.1.2.0/24".
When Remote Administration is enabled, the web server port will be shifted to default port 80.
To change the Remote Administration web server port, enter the desired port number to the last field.
Eg. Port 8080
Denial of Service (DoS) Attack Detection. When enabled, the router can detect the following (and more) DoS attack types:
SYN Attack
WinNuke
Port Scan
Ping of Death
Land Attack
Enable Log to record DoS attack details.
Click Save to save the settings or Undo to cancel.
www.netcommwireless.com
Ver 1.2
NetComm Wireless NB16WV-02 User Guide
54
Advanced Settings
The Advanced Settings page allows you to configure the advanced settings on the router such as the System log, Dynamic DNS
and SNMP options.
Status
The Status page displays the current System time, and lists any configured Dynamic DNS (DDNS) accounts, any Static or
Dynamic Routes added or any Quality of Service (QoS) rules in place.
NetComm Wireless NB16WV-02 User Guide
55
www.netcommwireless.com
Ver 1.2
System Log
This enables you to set up the system log features of the router. You can also choose to send the system log to a remote syslog
server (via a UDP connection) or email a copy to a recipient.
OPTION
DEFINITION
IP Address for remote System Logs (syslog)
The IP address of the syslog server where the system log data will be sent. Click the "Enable" checkbox to
enable this function.
Email address to send syslog to
Click the “Enable” checkbox to enable this function.
SMTP Server : port
Enter the IP address or fully qualified domain name (FQDN) and port for the selected email server.
SMTP Username
The SMTP username required to send email (if required).
SMTP Password
The SMTP password required to send email (if required).
Email Addresses
Enter the email addresses to send a copy of the current syslog to.
Email Subject
Enter the email subject to show on any sent emails.
View Log…
View the current system log.
Email Log Now
Email the current syslog to the entered email addresses.
www.netcommwireless.com
Ver 1.2
NetComm Wireless NB16WV-02 User Guide
56
Dynamic DNS
The Dynamic DNS feature enables users to set a static domain name for their internet connection even when the ISP only
provides a dynamic IP address.
By mapping the host name to the current public IP address of the router, users who want to connect to the router or any services
behind the router from the internet can just use the Dynamic DNS hostname instead of the IP Address which might change every
time the router connects to the Internet.
Before you can use a Dynamic DNS service, you need to register an account on one of the many supported Dynamic DNS
providers such as DynDNS.org, TZO.com or dhs.org.
After registering the account, the Dynamic DNS provider will provide you with the following details:
Host Name
Username/Email
Password/Key
To enable the Dynamic DNS feature on the unit, select the Enable option, choose the appropriate Dynamic DNS Provider and
enter the details supplied by your Dynamic DNS provider.
Click Save to save the settings or Undo to cancel.
NetComm Wireless NB16WV-02 User Guide
57
www.netcommwireless.com
Ver 1.2
QoS
Quality of Service (QoS) provides different priority to different users or data flows. It can also guarantee a certain level of
performance.
OPTION
DEFINITION
QoS
Use the drop down list to Enable or Disable QoS.
WAN Interface
Use the drop down list to select the interface to which QoS should apply.
QoS Mode
Use the drop down list to select the type of QoS to apply. Smart-QoS lets the router devide on the best settings based
on the types of service you select below and the percentage setting assigned to each type of service. Higher
percentages give a higher quality of service for that service type.
Bandwidth of Upstream
Enter the upstream bandwidth in Kilobits per second of your connection so that the router can calculate the best QoS
settings.
Bandwidth of Downstream
Enter the downstream bandwidth in Kilobits per second of your connection so that the router can calculate the best QoS
settings.
The lower section of the screen lets you manually assign a percentage of bandwidth to the different service types. If you manually
assign QoS, the total percentage must add up to 90%. The remaining 10% of bandwidth is reserved for other types of network
traffic.
For advanced QoS configuration, use the QoS Mode drop down list to select User-defined QoS Rule to display the QoS rules
table. Click the Add A New Rule button to configure a new QoS rule.
OPTION
DEFINITION
Rule
Select to enable or disable the QoS rule.
Class
Select the class of traffic you would like to prioritise.
Class Info
Enter the range of IP addresses of the class.
Function
Select the function of the rule. You can select from Priority, Max Rate, Session, Drop, Log or Alert.
Function data - Priority
Enter a priority value from 1 to 6 with 1 being the highest.
Direction
Select the direction of traffic to prioritise. Available options include In, Out or Both.
Schedule
Select a schedule for the new rule to apply. Previously created schedules are visible here or you can select the rule to
always apply.
Note: For further instructions on scheduling rules, please refer to the “Scheduling” section later in this guide
Click on Save to store your setting or Undo to discard your changes.
www.netcommwireless.com
Ver 1.2
NetComm Wireless NB16WV-02 User Guide
58
SNMP
SNMP (Simple Network Management Protocol) is a protocol designed to give a user the capability to remotely manage a
computer network by polling and setting terminal values and monitoring network events.
OPTION
DEFINITION
Enable SNMP
You must check Local, Remote or both to enable SNMP function. If Local is checked, this device will only respond to requests
from LAN connected hosts. If Remote is checked, this device will respond to requests from the WAN connection.
Get Community
Sets the community string your device will respond to for Read-Only access.
Set Community
Sets the community string your device will respond to for Read/Write access.
IP 1, IP 2, IP 3, IP 4
Input your SNMP Management host IP here. You will need to configure the address where the device should send SNMP Trap
messages to.
SNMP Version
Please select proper SNMP Version that your SNMP Management software supports.
WAN Access IP Address
You can limit remote access to a specific IP address by entering it here.
Note: If "Remote" access is enabled, the default setting of 0.0.0.0 means any IP obtain SNMP protocol Information.
Click the Save button to store your setting or the Undo button to discard your changes.
NetComm Wireless NB16WV-02 User Guide
59
www.netcommwireless.com
Ver 1.2
Routing
Routing tables allow you to determine which physical interface address to use for outgoing IP data. If you have more than one
router and subnet, you will need to configure the routing table to allow packets to find the proper routing path and allow different
subnets to communicate with each other.
These settings are used to setup the static and dynamic routing features of the NB16WV-02.
Dynamic Routing:
Routing Information Protocol (RIP) will exchange information about different host destinations for working out routes throughout
the network.
Note: Only select RIPv2 if you have a different subnet in your network. Otherwise, select RIPv1.
Static Routing:
For static routing, you can specify up to 8 routing rules.
You need to enter the destination IP address, subnet mask, gateway, and hop for each routing rule, then enable the rule by
selecting the Enable checkbox.
Click the Save button to store your setting or the Undo button to discard your changes.
www.netcommwireless.com
Ver 1.2
NetComm Wireless NB16WV-02 User Guide
60
System Time
This page allows you to change the System time setting on the NB16WV-02.
OPTION
DEFINITION
Time Zone
Select the time zone where this device is located.
Auto-Synchronization
Select the "Enable" checkbox to enable this function.
Enable Daylight Saving
Enables or disables the router’s automatic daylight saving adjustment feature.
Daylight Savings Dates
Use the drop down lists to select a daylight saving start and end date and time.
Time Server
Select a NTP time server to obtain the current UTC time from.
Sync with Time Server
Select if you want to set Date and Time by NTP Protocol.
Sync with my PC
Select if you want to set Date and Time using your computers Date and Time
Click Save to save the settings or Undo to cancel.
NetComm Wireless NB16WV-02 User Guide
61
www.netcommwireless.com
Ver 1.2
Scheduling
You can use scheduling to enable or disable a service at a specific time or on a specific day.
Select Enable and then click the Add New Rule button.
Select a name for the rule and enter the details such as the day, start time or end time and click the Save button
In the example below, the rule is called “Work Hours” and it is only active between 08:00 and 17:30.
You are then able to select the scheduling rule name specified from the Packet Filter configuration section to perform the
configured filtering at the scheduled time as per the screenshot below.
www.netcommwireless.com
Ver 1.2
NetComm Wireless NB16WV-02 User Guide
62
This example would prevent any access to the IP address 66.102.11.104 from any device connected to the router, 7 days a
week, only between the hours of 08:00 and 17:30.
Click the Save button to save the settings or the Undo button to cancel.
NetComm Wireless NB16WV-02 User Guide
63
www.netcommwireless.com
Ver 1.2
IPv6
The IPv6 page enables you to configure the settings used for an IPv6 connection (if supported by your Internet Service Provider).
OPTION
DEFINITION
IPv6
Select to enable or disable IPv6 functionality.
IPv6 Interface
Configure IPv6 for the selected interface.
IPv6 Connection
Select the type of IPv6 connection to utilise for your service. You can select from:

Static IPv6

DHCPv6

PPPoE

6 to 4

IPv6 in IPv4 Tunnel

PPPoA
Select the type of connection as required by your Internet Service Provider for their IPv6 service.
DNS Setting
Select whether to automatically obtain DNS Server addresses or use the ones you manually specified.
Primary DNS Address
Enter the Primary DNS Address for the IPv6 connection.
Secondary DNS Address
Enter the Secondary DNS Address for the IPv6 connection.
LAN IPv6 Address
The IP Address to use for the IPv6 LAN interface.
LAN IPv6 Link-Local Address
The current local LAN IPv6 address of the NB16WV-02.
Autoconfiguration
Select to enable or disable IPv6 auto configuration (if supported by your Internet Service Provider). Disable IPv6 /64 Prefix
delegation.
Autoconfiguraion Type
Enabling Stateless or stateful IPv6, allowing defined IPv6 /64 addressing or automatic globally unique IPv6 address.
Router Advertisement Lifetime
Enter the length of time between the router advertising its configuration on the IPv6 connection.
www.netcommwireless.com
Ver 1.2
NetComm Wireless NB16WV-02 User Guide
64
TR-069
The TR-069 client allows the NB16WV-02 to be automatically configured from a TR-069 server. Enter the applicable configuration
options to enable the router to contact the TR-069 server and retrieve any configuration options.
OPTION
DEFINITION
TR-069
Select to enable or disable the TR-069 automatic configuration function.
ACS URL
Enter the URL of the ACS server for automatic configuration.
ACS User Name
The username required to login to the ACS server.
ACS Password
The password required to login to the ACS server.
Connection Request Port
The port number the ACS server is running on.
Connection Request Username
The username to use when a connection request is made to the CPE.
Connection Request Password
The password to use when a connection request is made to the CPE.
Inform
Select to enable or disable the Inform function for ACS connections.
Interval
Select the interval between Inform updates if Inform has been enabled.
Click the Save button to store any changes to the settings.
NetComm Wireless NB16WV-02 User Guide
65
www.netcommwireless.com
Ver 1.2
VLAN
The VLAN page provides you with the ability to create Virtual Local Area Networks (VLANs). A VLAN is layer-2 network which has
been partitioned to create multiple distinct broadcast domains. The purpose of this is to isolate packets so that they may only
pass between these broadcast domains via one or more routers.
OPTION
DEFINITION
Ethernet
The number of the physical port on the rear of the router for which the VLAN will be
created.
WAN/LAN
The function of the port. Port 1 only functions as a WAN port.
VID
The Virtual LAN ID you want to assign to the VLAN.
Tx TAG
Selecting this option will tag packet headers with the VLAN ID.
To adjust advanced WAN VLAN settings for a particular VID, click the WAN VLAN Settings button. The following window is
displayed:
OPTION
DEFINITION
VID
Use the drop down list to select the VID you want to configure.
Routing Type
Use the drop down list to type of routing for the selected VID.
DHCP Setting
Displays the current DHCP setting.
Setting Routing Type to Bridge displays further options:
OPTION
Use the drop down list to select the VID you want to configure.
Routing Type
Use the drop down list to type of routing for the selected VID.
WAN type
Use the drop down list to select which WAN type the VLAN uses.
WAN Map VLAN ID
Enter the VLAN ID to tag packets on the WAN interface.
www.netcommwireless.com
Ver 1.2
DEFINITION
VID
NetComm Wireless NB16WV-02 User Guide
66
VoIP Settings
Configurations
Service Domain
The Service Domain page is where you enter your VoIP service settings as supplied by your VoIP service provider (VSP). If you are
unsure about a specific setting or have not been supplied information for a particular field, please contact your VoIP service
provider to verify if this setting is needed.
OPTION
DEFINITION
Display Name
Enter the display name for your VoIP service.
User Name
Enter the User Name for your VoIP service.
Register Name
Enter the Register Name (May be called the “Auth ID”) for your VoIP service.
Register Password
Enter the Register Password (May be called the “Auth Password”) for your VoIP service.
Domain
Enter the Domain for your VoIP service.
Registrar/Proxy Server
Enter the Registrar or Proxy Server address for your VoIP service.
Use Outbound Server
Enable or Disable the use of an Outbound Proxy for VOIP calls.
Outbound Proxy
Enter the Outbound Proxy server address to use.
Status
The current status of your VoIP service.
Click Save to save your settings and connect to your VoIP service or Undo to discard the settings entered.
NetComm Wireless NB16WV-02 User Guide
67
www.netcommwireless.com
Ver 1.2
Port Setting
The Port Setting page enables you to specify a different SIP or RTP Port number to connect to your VoIP service on
OPTION
DEFINITION
SIP Port
Select the port for SIP traffic to use.
RTP Port
Select the port for RTP traffic to use.
This setting should not need to be changed unless directed to do so.Please contact your VoIP service provider to verify the port
number for their VoIP Service.
Click Save to save your settings or Undo to discard the settings entered.
Codec Setting
The Codec Setting page enables you to select which audio codec to use with your VoIP service. This information will usually be
supplied by your VoIP service provider and should not need to be changed unless you are experiencing issues with VoIP call
sound quality.
The following codec are available for use:
G.729
G.711 a-law
G.711 u-law
G.726 -32
www.netcommwireless.com
Ver 1.2
NetComm Wireless NB16WV-02 User Guide
68
OPTION
DEFINITION
Codec Priority 1
Set the codec you would like to try first with your VoIP service.
Codec Priority 2
Set the codec you would like to try second with your VoIP service.
Codec Priority 3
Set the codec you would like to try third with your VoIP service.
Codec Priority 4
Set the codec you would like to try fourth with your VoIP service.
G.711 & G.729 Packet Length
Adjust the packet length size. This can reduce or increase the bandwidth required and call usability
for a VoIP call.
Voice VAD
Adjust the ‘Voice Activity Detection’ interval.
This should not be adjusted unless the words in your conversation are being cut off.
(This setting should not need to be changed.)
The packet length for Comfort
noise packet
Set the time in milliseconds for which comfort noise is used to simulate background noise at your
end of the connection.
Click Save to save your settings or Undo to discard the settings entered.
NetComm Wireless NB16WV-02 User Guide
69
www.netcommwireless.com
Ver 1.2
DTMF Setting
The Dual-Tone Multi-Frequency signalling (DTMF) Setting page enables you to specify which DTMF standard to use
on your VoIP service.
The following DTMF standards are available for use:
RFC 2833
Inband DTMF
Send DTMF SIP Info
This information will usually be supplied by your VoIP service provider and should not need to be changed unless you are
experiencing issues with DTMF based services
(Automated Telephone services, Answering machines, etc).
OPTION
DEFINITION
DTMF Setting
Select which DTMF standard you would like to use.
Click Save to save your settings or Undo to discard the settings entered.
STUN Settings
The STUN Settings page enables you to configure settings related to using a STUN server with your VoIP service. A STUN
(Session Traversal Utilities for NAT) server is used to permit NAT traversal for applications of real-time voice, video, messaging and
other interactive IP communications. This information will usually be supplied by your VoIP service provider and should not be
needed unless you are experiencing issues with VoIP calls or signing into your VoIP service.
OPTION
DEFINITION
SIP ALG
A SIP Application Gateway provides functionality to allow VoIP traffic to pass
both from the private the public and public to private side of the firewall
when using network address translation (NAT).
STUN
Select to Enable or Disable the STUN server functionality of the NB16WV.
STUN Server
Enter the STUN Server address to use.
STUN Port
Enter the Port with which to connect to the STUN server on.
Click Save to save your settings or Undo to discard the settings entered.
www.netcommwireless.com
Ver 1.2
NetComm Wireless NB16WV-02 User Guide
70
Telephony Profile
The Telephony Profile page enables you to configure the way the FXS phone port (RJ-11) operates.
Use the drop down list to select the region closest to you to configure the FXS port operation.
Click Save to save your settings or Undo to discard the settings entered.
Dial Plan
The Dial Plan page allows you to specify dial strings. When a dialled phone number matches a dial string, the number is dialled
immediately instead of waiting for a timeout to occur.
The included default dial plan only applies to Australia. For your local dial plan, contact your VoIP service provider.
Click Save to save your settings or Undo to discard the settings entered.
Other Settings
The Other Settings page enables you to specify a different SIP expire time and select to enable the DNS SRV function. This
information will usually be supplied by your VoIP service provider and should not need to be changed unless you are experiencing
issues with VoIP calls or signing into your VoIP service.
OPTION
DEFINITION
SIP Expire Time
Set the length of time between the NB16WV-02 refreshing its connection to your VoIP service
provider
Use DNS SRV
Enable or Disable the DNS SRV function on the NB16WV-02.
SIP ALG
A SIP Application Gateway provides functionality to allow VoIP traffic to pass both from the private
the public and public to private side of the firewall when using network address translation (NAT).
Rport
Rport allows a client to request that the server send the response back to the source IP address
and port from which the request originated.
Click Save to save your settings or Undo to discard the settings entered.
NetComm Wireless NB16WV-02 User Guide
71
www.netcommwireless.com
Ver 1.2
Call Features
The Call Features pages enable you to configure settings for features such as call waiting, call forwarding and caller ID.
Call Forward
The Call Forward page enables you to configure the type of call forwarding you would like to use and the SIP address to which
any such calls should be forwarded.
You can select from the following call forwarding conditions:
Always
Busy
No Answer
Disable
OPTION
DEFINITION
Type
Select the type of Call Forwarding you would like to use.
URL
Enter the address (Phone number) to forward VoIP calls to.
Call forwarding Ring
time
Enter the amount of time the incoming call rings before call
forwarding is activated.
Click Save to save your settings or Undo to discard the settings entered.
DND Setting
The DND Setting page enables you to configure Do Not Disturb (DND) mode. This will prevent calls coming through to your
phone.
OPTION
DND Always
DEFINITION
Enable or Disable the DND feature.
Click Save to save your settings or Undo to discard the settings entered.
www.netcommwireless.com
Ver 1.2
NetComm Wireless NB16WV-02 User Guide
72
Caller ID
The Caller ID page enables you to configure whether your Caller ID is sent when receiving an inbound call.
(If supported by your VoIP service and phone caller ID service)
OPTION
Caller ID
DEFINITION
Select to use or Disable Caller ID.
Click Save to save your settings or Undo to discard the settings entered.
Flash Time
The Flash Time page enables you to configure the minimum and maximum time a hook flash signal can occur for the NB16WV-02
to recognise it.
OPTION
DEFINITION
FXS Flash Signal Detect (MAX)
Enter the maximum time (in milliseconds) to detect a hook flash.
FXS Flash Signal Detect (MIN)
Enter the minimum time (in milliseconds) to detect a hook flash.
This setting should not need to be changed unless directed to do so.
Click Save to save your settings or Undo to discard the settings entered.
NetComm Wireless NB16WV-02 User Guide
73
www.netcommwireless.com
Ver 1.2
Call Waiting
The Call Waiting page enables you to utilise call waiting with your VoIP service.
(If supported by your VoIP service)
OPTION
Call Waiting
DEFINITION
Select to Enable or Disable the call waiting feature on the NB16WV.
Click Save to save your settings or Undo to discard the settings entered.
Hot Line
The Hot Line page enables you to configure a telephone number which can be called without dialling any numbers at all (simply
pick up the telephone handset) after the specified waiting time.
OPTION
DEFINITION
Use Hot Line
Select to Enable or Disable the Hot Line feature of the NB16WV-02.
Hot Line Number
Enter the number to forward Hot Line calls to.
Waiting time before starting Hot Line
Enter the amount of time to wait before forwarding a call to the Hot Line number.
Click Save to save your settings or Undo to discard the settings entered.
www.netcommwireless.com
Ver 1.2
NetComm Wireless NB16WV-02 User Guide
74
Call Features
The Call Features page enables you to configure the dialling codes used to activate or deactivate features on your VoIP service via
your handset number pad.
(If supported by your VoIP Provider and your handset.)
You can change the dial codes on the following VoIP service features:
Blind Call Transfer
Anonymous Call Enable
Anonymous Call Disable
Anonymous Call per Call Basis
DND Enable
DND Disable
Call Forwarding Enable
Call Forwarding Disable
Call Return
Click Save to save your settings or Undo to discard the settings entered.
NetComm Wireless NB16WV-02 User Guide
75
www.netcommwireless.com
Ver 1.2
Phone Book
The Phone Book page lets you to enter phone numbers into a database for easy calling. Phone book numbers are stored on the
NB16WV-02.
The Phone Book page enables you to enter phone book entries. You are able to enter up to 140 entries.
The corresponding name is displayed when a VoIP call is received from that number.
(If supported by your VoIP service and telephone handset)
Click Save to save your settings or Undo to discard the settings entered.
To make calls using Phone Book, enter the ID number of the corresponding Phone Number, and wait for dial out wait time to
elapse.
www.netcommwireless.com
Ver 1.2
NetComm Wireless NB16WV-02 User Guide
76
NAS Settings
The NAS Settings page enables you to configure the network area storage (NAS) function of the NB16WV-02. This function can
be used to remotely access files stored on an attached USB hard drive. Click on any of the menu items to access the respective
configuration page.
Disk Utility
The Disk Utility function enables you to check any attached USB storage for errors. The NB16WV will scan the attached storage
and determine if there are any file system errors present. File System errors can prevent you being able to access stored content.
You can also format (erase) any attached storage if needed. Simply click the appropriate button to perform either task.
File Sharing
The File Sharing function enables the NB16WV-02 to take part in a Windows networking environment. Once configured, the
attached USB Storage can be viewed from Windows by typing:
\\<Configured Name of the NB16WV-02>\Storage\
Eg, \\NAS\Storage
Files can then be dragged and dropped onto the attached USB storage.
OPTION
DEFINITION
Network Attached Storage Name
Enter the computer name the NB16WV is to use on the network.
WorkGroup
Enter the network workgroup the NB16WV is to be a member of.
Server Comment
Enter the comment to be displayed when a list of network hosts is shown.
The File Sharing configuration also enables you to enable the built-in FTP server function and the associated settings:
OPTION
DEFINITION
FTP
Select to enable or disable the FTP server function.
FTP Port
Enter the network port the FTP server should run on.
FTP Max Connections per IP
Enter the maximum number of concurrent connections which can be used by a particular IP address.
FTP Max Clients
Enter the maximum number of clients which can connect to the FTP concurrently.
Client Support UTF8
Enable Unicode support for connected clients.
Access Control
The Access Control function provides control over which users can access any attached USB Storage. By default, the NB16WV02 is in “Guest Mode” which means anyone can access the attached hard drive.
NetComm Wireless NB16WV-02 User Guide
77
www.netcommwireless.com
Ver 1.2
Enabling “Authorization Mode” allows the creation of specific user accounts with a password to further control access
permissions. To enable this, click on the Authorization Mode radio button and click Save. You can then click on the User
Configuration button in order to create the required user accounts.
Add the user name and password and then click the Add button. Alternatively, to remove a user, click on the radio button to the
right of the username and then select Delete.
www.netcommwireless.com
Ver 1.2
NetComm Wireless NB16WV-02 User Guide
78
Download Assistant
The Download Assistant enables you to schedule the NB16WV to perform a download from an Internet host.
You are able to select from two download types:
FTP
HTTP
Each type of download job requires different configuration options.
FTP
OPTION
DEFINITION
Job Name
A name to identify the download job.
URL
The address to download from.
Port
The port required for the FTP server (This would usually be left as 21).
Save To
The location on the NB16WV to save the downloaded file to.
Login Method
Select the type of authentication required by the FTP server (Selecting anonymous means a username and password are not required).
Username
The username required to access the FTP server.
Password
The password required to access the FTP server.
Start Time
Select to either schedule a time for the download to begin or start the download immediately.
NetComm Wireless NB16WV-02 User Guide
79
www.netcommwireless.com
Ver 1.2
HTTP
OPTION
DEFINITION
Job Name
A name to identify the download job.
URL
The address to download from.
Save To
The location on the NB16WV to save the downloaded file to.
Start Time
Select to either schedule a time for the download to begin or start the download immediately.
You can also configure the NB16WV-02 to send an e-mail on completion of the scheduled download. Click on the “E-mail Alert
Configuration” button to setup this option.
OPTION
Select to enable or disable an alert to be sent for a completed HTTP download.
FTP Download Alert
Select to enable or disable an alert to be sent for a completed FTP download.
USB Download Alert
Select to enable or disable an alert to be sent for a completed USB download.
SMTP Server Address
Enter the address of the email server to be used to send the alerts.
SMTP Server Port
Enter the port which the email server is running on.
SMTP User Name
Enter the username required to login to the email server.
SMTP Password
Enter the password required to login to the email server.
Email Address
Enter the email address any alerts are to be sent to.
Email Subject
Enter the subject to be used on any email alerts sent out.
Reservation Disk Space
Enter the amount of disk space to reserve on the NB16WV for the specified download.
www.netcommwireless.com
Ver 1.2
DEFINITION
HTTP Download Alert
NetComm Wireless NB16WV-02 User Guide
80
Download Status
The Download Status page enables you to monitor previously scheduled Download Assistant jobs. From this page you are able to
Start, Pause, Resume or Delete any Download Assistant jobs.
The View drop-down list enables you to select whether currently running jobs, waiting jobs or scheduled jobs are displayed. Once
listed, click on the checkbox on the left hand side of the listed jobs and then click the appropriate function button.
Web HDD
The Web HDD function provides a web page based Windows Explorer type view of the content of any attached USB storage.
Using this interface you are able to upload, download or delete files and folders as well as create directories. Click through the
displayed folders to show any stored files.
Left click on any items to select them and click the appropriate button or double click folders to view any content.
To upload files to your Web HDD. To do this, click the Upload button. You can then click the Browse button and then navigate to
the file you would like to upload. Once selected, this file will be copied to the Web HDD and become available to download by
connected devices.
NetComm Wireless NB16WV-02 User Guide
81
www.netcommwireless.com
Ver 1.2
Toolbox
The toolbox menu provides access to various settings and maintenance functions of the router.
System Info
The System Info screen displays the general settings on the router, such as the WAN type, the date and time, the log types and
the log data.
Routing Table
The Routing table displays the current routes in place on the router.
Click the Refresh button to update this list.
Restore Settings
The Restore settings page allows you to restore a previously saved configuration of the router. This is handy for reverting to a
working configuration when making changes to the router’s settings.
To restore the router configuration, click the Browse button, select the saved configuration file and then click the Restore button.
www.netcommwireless.com
Ver 1.2
NetComm Wireless NB16WV-02 User Guide
82
Firmware Upgrade
This page lets you upgrade the firmware of the router. The firmware is the system running on the router. New firmware updates
are regularly made available and can fix bugs and add new features.
Backup Settings
Click the Backup Settings menu item to save the current configuration of the router to a file for safe-keeping.
Reset to Default
Click the Reset to Default menu item to set the configuration of the router to the factory default settings.
Note: This will erase all configuration settings. Ensure you have a backup of your configuration before proceeding to reset
to default settings.
Reboot
Click the Reboot menu item to restart the router.
Startup Wizard
Click the Startup Wizard menu item if you want to run the initial wizard that showed the first time you installed your router.
Miscellaneous
The miscellaneous page provides options to send a Wake-on-LAN packet to a specified IP, ping a specified domain name or IP
address and brighten or dim the front LEDs of the router.
Logout
The Logout menu item logs you out of the router.
NetComm Wireless NB16WV-02 User Guide
83
www.netcommwireless.com
Ver 1.2
Additional Product Information
Establishing a wireless connection
Windows XP (Service Pack 3)
1.
2.
3.
4.
5.
Open the Network Connections control panel (Start -> Control Panel -> Network Connections):
Right-click on your Wireless Network Connection and select View Available Wireless Networks:
Select the wireless network listed on your included wireless security card and click Connect.
Enter the network key (refer to the included wireless security card for the default wireless network key).
The connection will show Connected.
Windows Vista
1.
2.
3.
4.
5.
6.
7.
Open the Network and Sharing Center (Start > Control Panel > Network and Sharing center).
Click on "Connect to a network".
Choose "Connect to the Internet" and click on "Next".
Select the wireless network listed on your included wireless security card and click Connect.
Enter the network key (refer to the included wireless security card for the default wireless network key).
Select the appropriate location. This will affect the firewall settings on the computer.
Click on both "Save this network" and "Start this connection automatically" and click "Next".
Windows 7
1.
2.
3.
4.
5.
6.
7.
8.
9.
Open the Network and Sharing Center (Start > Control Panel > Network and Sharing center).
Click on "Change Adapter settings" on the left-hand side.
Right-click on "Wireless Network Connection" and select "Connect / Disconnect".
Select the wireless network listed on your included wireless security card and click Connect.
Enter the network key (refer to the included wireless security card for the default wireless network key).
You may then see a window that asks you to "Select a location for the 'wireless' network". Please select the "Home" location.
You may then see a window prompting you to setup a "HomeGroup". Click "Cancel" on this.
You can verify your wireless connection by clicking the "Wireless Signal" indicator in your system tray.
After clicking on this, you should see an entry matching the SSID of your NB16WV-02 with "Connected" next to it.
Windows 8/8.1
1.
2.
3.
4.
5.
6.
7.
Open the Network and Sharing Center (Click on Start, Type “Network and Sharing Center”)
Click on “Change adapter settings” on the left hand column.
Right-click on Wireless Network Adaptor and select "Connect / Disconnect".
Select the wireless network listed on your included wireless security card and click Connect.
Enter the network key (refer to the included wireless security card for the default wireless network key).
You can verify your wireless connection by clicking the "Wireless Signal" indicator in your system tray.
After clicking on this, you should see an entry matching the SSID of your NB16WV-02 with "Connected" under it.
Mac OSX 10.6
1.
2.
3.
4.
Click on the Airport icon on the top right menu.
Select the wireless network listed on your included wireless security card and click Connect.
On the new window, select “Show Password”, type in the network key (refer to the included wireless security card for the
default wireless network key) in the Password field and then click on OK.
To check the connection, click on the Airport icon and there should be a tick on the wireless network name.
Note: For other operating systems, or if you use a wireless adaptor utility to configure your wireless connection, please
consult the wireless adapter documentation for instructions on establishing a wireless connection.
www.netcommwireless.com
Ver 1.2
NetComm Wireless NB16WV-02 User Guide
84
Troubleshooting
Using the indicator lights (LEDs) to Diagnose Problems
The LEDs are useful aides for finding possible problem causes.
Power LED
The Power LED does not light up.
STEP
CORRECTIVE ACTION
1
Make sure that the NB16WV-02 power adaptor is connected to the device and plugged in to an appropriate
power source. Use only the supplied power adaptor.
2
Check that the NB16WV-02 and the power source are both turned on and device is receiving sufficient
power.
3
Turn the NB16WV-02 off and on.
4
If the error persists, you may have a hardware problem. In this case, you should contact technical support.
Technical Data
The following table lists the hardware specifications of the NB16WV-02.
MODEL
NB16WV-02
ADSL2+
ITU 992.1 (G.dmt) Annex A
ITU 992.2 (G.lite)
ITU 992.3 ADSL2 (G.dmt.bis, Annex J/L)
ITU 992.5 ADSL2+ (Annex M)
Wireless WAN
1 x USB 2.0 port for external HSPA/LTE modem
PPP (for WCDMA / HSPA)
Ethernet WAN
1 x Gigabit WAN port (10/100/1000 Mbps)
Connectivity
2 x USB 2.0, 4 x 10/100/1000 Mbps, 1 x RJ-11 ADSL, 1 x RJ-11 Telephone Handset, 1 x WLAN
LED Indicators
Operating Temperature
Power, ADSL, 3G, WWW, LAN 1-4, WAN, WIFI, VoIP
Operating temperature: 0˚C - 40˚C, Humidity: 10%-90% non-condensing
Storage temperature: -10˚C - 70˚C, Humidity: 0%-95% non-condensing
Power Input
12V DC - 2.5A
Dimensions & Weight
215 mm (L) x 145 mm (W) x 37 mm (H)
403 grams
VoIP
Regulatory Compliance
PROTOCOL
SIP 2.0
VOICE COMPRESSION
G.711-Alaw voice compression
G.711-Mulaw voice compression
G.726-32 voice compression
G.729AB voice compression
G.168 116 ms tail line echo cancellation
CALL FUNCTION
Call forward
Caller ID
Dial plan
Call waiting
3-way conference call
Hot line
A-Tick
Electrical Specifications
It is recommended that the NB16WV-02 be powered by the supplied 12V DC, 2.5A power supply. A replacement power supply is
available from the NetComm Wireless Online shop.
Environmental Specifications / Tolerances
The NB16WV-02 housing enables it to operate over a wide variety of temperatures from 0˚C - 40˚C (operating temperature).
NetComm Wireless NB16WV-02 User Guide
85
www.netcommwireless.com
Ver 1.2
Legal & Regulatory Information
Intellectual Property Rights
All intellectual property rights (including copyright and trade mark rights) subsisting in, relating to or arising out this Manual are
owned by and vest in NetComm Wireless (ACN 002490486) (NetComm Wireless Limited) (or its licensors). This Manual does not
transfer any right, title or interest in NetComm Wireless Limited’s (or its licensors’) intellectual property rights to you.
You are permitted to use this Manual for the sole purpose of using the NetComm Wireless product to which it relates. Otherwise
no part of this Manual may be reproduced, stored in a retrieval system or transmitted in any form, by any means, be it electronic,
mechanical, recording or otherwise, without the prior written permission of NetComm Wireless Limited.
NetComm, NetComm Wireless and NetComm Wireless Limited are a trademark of NetComm Wireless Limited. All other
trademarks are acknowledged to be the property of their respective owners.
Customer Information
The Australian Communications & Media Authority (ACMA) requires you to be aware of the following information and warnings:
1.
This unit may be connected to the Telecommunication Network through a line cord which meets the requirements of the
AS/CA S008-2011 Standard.
2.
This equipment incorporates a radio transmitting device, in normal use a separation distance of 20cm will ensure radio
frequency exposure levels complies with Australian and New Zealand standards.
3.
This equipment has been tested and found to comply with the Standards for C-Tick and or A-Tick as set by the ACMA.
These standards are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio noise and, if not installed and used in accordance with the
instructions detailed within this manual, may cause interference to radio communications. However, there is no guarantee
that interference will not occur with the installation of this product in your home or office. If this equipment does cause
some degree of interference to radio or television reception, which can be determined by turning the equipment off and
on, we encourage the user to try to correct the interference by one or more of the following measures:
4.
i.
Change the direction or relocate the receiving antenna.
ii.
Increase the separation between this equipment and the receiver.
iii.
Connect the equipment to an alternate power outlet on a different power circuit from that to which the receiver/TV is
connected.
iv.
Consult an experienced radio/TV technician for help.
The power supply that is provided with this unit is only intended for use with this product. Do not use this power supply
with any other product or do not use any other power supply that is not approved for use with this product by NetComm
Wireless. Failure to do so may cause damage to this product, fire or result in personal injury.
Consumer Protection Laws
Australian and New Zealand consumer law in certain circumstances implies mandatory guarantees, conditions and warranties
which cannot be excluded by NetComm and legislation of another country's Government may have a similar effect (together these
are the Consumer Protection Laws). Any warranty or representation provided by NetComm is in addition to, and not in
replacement of, your rights under such Consumer Protection Laws.
If you purchased our goods in Australia and you are a consumer, you are entitled to a replacement or refund for a major failure
and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or
replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. If you purchased our
goods in New Zealand and are a consumer you will also be entitled to similar statutory guarantees.
www.netcommwireless.com
Ver 1.2
NetComm Wireless NB16WV-02 User Guide
86
Product Warranty
All NetComm Wireless products have a standard one (1) year warranty from date of purchase, however, some products have an
extended warranty option (refer to packaging and the warranty card) (each a Product Warranty). To be eligible for the extended
warranty option you must supply the requested warranty information to NetComm Wireless Limited within 30 days of the original
purchase date by registering online via the NetComm Wireless web site at www.netcommwireless.com. For all Product Warranty
claims you will require proof of purchase. All Product Warranties are in addition to your rights and remedies under applicable
Consumer Protection Laws which cannot be excluded (see Consumer Protection Laws Section above).
Subject to your rights and remedies under applicable Consumer Protection Laws which cannot be excluded (see the Consumer
Protection Laws Section above), the Product Warranty is granted on the following conditions:
1.
the Product Warranty extends to the original purchaser (you / the customer) and is not transferable;
2.
the Product Warranty shall not apply to software programs, batteries, power supplies, cables or other accessories
supplied in or with the product;
3.
the customer complies with all of the terms of any relevant agreement with NetComm and any other reasonable
requirements of NetComm including producing such evidence of purchase as NetComm may require;
4.
the cost of transporting product to and from NetComm’s nominated premises is your responsibility;
5.
NetComm Wireless Limited does not have any liability or responsibility under the Product Warranty where any cost, loss,
injury or damage of any kind, whether direct, indirect, consequential, incidental or otherwise arises out of events beyond
NetComm’s reasonable control. This includes but is not limited to: acts of God, war, riot, embargoes, acts of civil or
military authorities, fire, floods, electricity outages, lightning, power surges, or shortages of materials or labour; and
6.
the customer is responsible for the security of their computer and network at all times. Security features may be disabled
within the factory default settings. NetComm Wireless Limited recommends that you enable these features to enhance
your security.
Subject to your rights and remedies under applicable Consumer Protection Laws which cannot be excluded (see Section 3
above), the Product Warranty is automatically voided if:
1.
you, or someone else, use the product, or attempt to use it, other than as specified by NetComm Wireless Limited;
2.
the fault or defect in your product is the result of a voltage surge subjected to the product either by the way of power
supply or communication line, whether caused by thunderstorm activity or any other cause(s);
3.
the fault is the result of accidental damage or damage in transit, including but not limited to liquid spillage;
4.
your product has been used for any purposes other than that for which it is sold, or in any way other than in strict
accordance with the user manual supplied;
5.
your product has been repaired or modified or attempted to be repaired or modified, other than by a qualified person at
a service centre authorised by NetComm Wireless Limited; or
6.
the serial number has been defaced or altered in any way or if the serial number plate has been removed.
Limitation of Liability
This clause does not apply to New Zealand consumers. Subject to your rights and remedies under applicable Consumer
Protection Laws which cannot be excluded (see the Consumer Protection Laws Section above), NetComm Wireless Limited
accepts no liability or responsibility, for consequences arising from the use of this product. NetComm Wireless Limited reserves
the right to change the specifications and operating details of this product without notice.
If any law implies a guarantee, condition or warranty in respect of goods or services supplied, and NetComm Wireless’s liability for
breach of that condition or warranty may not be excluded but may be limited, then subject to your rights and remedies under any
applicable Consumer Protection Laws which cannot be excluded, NetComm Wireless’s liability for any breach of that guarantee,
condition or warranty is limited to: (i) in the case of a supply of goods, NetComm Wireless Limited doing any one or more of the
following: replacing the goods or supplying equivalent goods; repairing the goods; paying the cost of replacing the goods or of
acquiring equivalent goods; or paying the cost of having the goods repaired; or (ii) in the case of a supply of services, NetComm
Wireless Limited doing either or both of the following: supplying the services again; or paying the cost of having the services
supplied again.
To the extent NetComm Wireless Limited is unable to limit its liability as set out above, NetComm Wireless Limited limits its liability
to the extent such liability is lawfully able to be limited.
NetComm Wireless NB16WV-02 User Guide
87
www.netcommwireless.com
Ver 1.2
Contact
Address: NETCOMM WIRELESS LIMITED Head Office
PO Box 1200, Lane Cove NSW 2066 Australia
Phone: +61(0)2 9424 2070
Fax: +61(0)2 9424 2010
Email: sales@netcommwireless.com techsupport@netcommwireless.com
www.netcommwireless.com
Ver 1.2
NetComm Wireless NB16WV-02 User Guide
88