MANNHART
OPERATING / TECHNICAL MANUAL
Salad Dryers
MODEL SD-PE
MODEL SD-PS
Made in U.S.A.
MANNHART, INC.
MANNHART
PRINTED IN U.S.A.
651 Industrial Boulevard
Grapevine, Texas 76051
Tel.: (817) 421-0100
Fax: (817) 421-0246
www.mannhart.com
©2001 MANNHART, INC.
Rev. 07/2006
Salad Dryers
MANNHART
Mannhart SD-PE / SD-PS
TECHNICAL MANUAL FOR MANNHART SALAD DRYERS
MODEL SD-PE & SD-PS
LITERATURE AND PARTS LIST
SD-PE
1. SD-PE LITERATURE
2. SD-PE BREAKDOWN
3. SD-PE PARTS DIAGRAM
4. SD-PE PARTS LIST
SD-PS
5. SD-PS LITERATURE
6. SD-PS BREAKDOWN
7. SD-PS PARTS DIAGRAM
8. SD-PS PARTS LIST
ELECTRICAL & OPERATING INSTRUCTIONS
9. ELECTRICAL WIRING DIAGRAM
10. OPERATING INSTRUCTIONS
11. CLEANING INSTRUCTIONS
12. BASKET FILLING INSTRUCTIONS
13. IMPORTANT NOTICE – FLOOR PLACEMENT
WARRANTY
14. WARRANTY INFORMATION
MANNHART
NEW
SALAD DRYER
MANNHART
MODEL SD-PE
“MAKES EVERY
DRIES ONE CASE OF LETTUCE
WITHIN MINUTES
SALAD
A WINNER!”
FRESH, CRISP APPEARANCE OF SALAD
EXTENDED SHELF LIFE
•
ALL POLYETHYLENE, HEAVY-DUTY
CONSTRUCTION, STAINLESS STEEL
REINFORCED
•
EASY TO REACH TIMER LOCATED AT
TOP OF TUB WITH POWER CORD
STORAGE
•
STAINLESS STEEL MOTOR
SPLASHGUARD PROTECTS FULLY
SEALED MOTOR
•
EASY TO LOAD POLYETHYLENE
SPIN BASKET WITH HAND GRIPS
•
WATER DRAINS THROUGH PVC
EXTENSION TUBE DIRECTLY INTO
FLOOR DRAIN OR CONTAINER UP
TO 9” HIGH - NO SPLASHING
•
EASY TO LOCK, HEAVY-DUTY
CASTERS WITH BRAKES
•
EASY TO CLEAN - NO HARD TO
REACH AREAS
•
ONE YEAR WARRANTY, PARTS &
LABOR
SAVE 15% OR MORE ON SALAD DRESSING
BUILT FROM THE GROUND UP!
MADE IN USA
MANNHART, INC.
MANNHART
651 Industrial Boulevard
Grapevine, Texas 76051
Tel (817) 421-0100
Fax (817) 421-0246
www.mannhart.com
Rev. 07/2006
1
MANNHART, INC.
MANNHART
651 Industrial Boulevard, Grapevine, Texas 76051
Phone (817) 421-0100
FAX (817) 421-0246
www.mannhart.com
MANNHART SALAD DRYER
Model SD-PE
Thick wall polyethylene lid with molded in renewable thread, with
storage hook for when lid is not in use.
Cast Aluminum Bearing Mount keeps Salad Dryer balanced when
running.
High Density Polyethylene lid, covers basket when spinning, prevents
salad from spilling.
Bushing for polyethylene lid.
T-Handle, easy to remove for cleaning lids.
High Density Polyethylene Basket with hand grips.
Cast Aluminum driver, easy to remove for cleaning or to replace.
Heavy-duty, rigid wall polyethylene tub.
Easy to reach electric timer with built in Power Cord storage. Operator
does not need to bend to turn on Salad Dryer.
Heavy-duty one-piece molded, stainless steel reinforced polyethylene
base. No openings or crevasses for food and water to get in.
Heavy Duty Casters with brakes.
PVC Drainpipe extension to floor minimizes splashing of water.
Specifications:
Height
Width
Depth
32”
24”
24”
Net Weight
Shipping Weight
60 lb.
85 lb.
Electrical:
115 Volt, 60 Hz, 1 / Fl. Amps 2.5 - 1/4 HP
Gear motor with thermal overload and permanently lubricated gear
drive.
2
PARTS DIAGRAM FOR MANNHART SALAD DRYER SD–PE
SALAD DRYER SD–PE
3
MANNHART
Salad Dryers
Mannhart SD-PE
MANNHART SALAD DRYER, MODEL SD-PE PARTS LIST
4
PART #
DESCRIPTION
QUANTITY
5001-PE
OUTER TUB LID, POLYETHYLENE
1
5005-PE
BEARING MOUNT W/SCREWS, CAST ALUMINUM
1
5006-PE
T-HANDLE ASSEMBLY, STAINLESS STEEL
1
5007-PE
DRYER BASKET LID, POLYETHYLENE
1
5008-PE
DELRIN BUSHING FOR BASKET LID
1
5009-PE
DRYER BASKET WITH LID, POLYETHYLENE
1
5013A-PS
DRAIN PIPE EXTENSION HOSE, VINYL
1
5015-PE
RUBBER GROMMET FOR ELECTRICAL CONDUIT PIPE
1
5021-PE
MOTOR WATER DEFLECTOR, STAINLESS STEEL
1
5026-PE
GEAR MOTOR - 115/60/1 - 1/4 HP
1
5026-PEA
GEAR MOTOR - 230/60/1 - 1/4 HP
1
5026-PEB
HEXAGON BOLTS W/LOCKWASHER TO FASTEN MOTOR
4
5027-PE
OCTAGONAL DRIVER FOR GEARMOTOR
1
5028-PE
MOTOR SPLASHGUARD, STAINLESS STEEL
1
5029-PE
ELECTRICAL CONDUIT PIPE
1
5034-PE
ELECTRICAL TIMER BOX
1
5036-PE
CABLE RELIEVE BUSHING FOR POWER CORD
1
5037-PE
FIVE MINUTE ELECTRICAL TIMER
1
5039-PE
POWER SUPPLY CORD 14/3 W/MOLDED PLUG 115/60/1
1
5039-PEA
POWER SUPPLY CORD 14/3 W/MOLDED PLUG 230/60/1
1
5042-PE
CASTERS W/POSITIVE LOCKING MECHANISM
3
MANNHART
SALAD DRYER
MODEL SD-PS
DRIES ONE CASE OF LETTUCE
WITHIN MINUTES
FRESH, CRISP APPEARANCE OF SALAD
EXTENDED SHELF LIFE
SAVES 15% OR MORE ON SALAD DRESSING
BUILT FROM THE GROUND UP!
“MAKES EVERY
SALAD
A WINNER!”
• STURDY POLYETHYLENE BASESTAINLESS STEEL REINFORCED
• STAINLESS STEEL TUB & LID HEAVY
16 GA, HIGHLY POLISHED
• EASY TO REACH TIMER LOCATED AT
TOP OF TUB WITH POWER CORD
STORAGE
• STAINLESS STEEL MOTOR SPLASHGUARD PROTECTS FULLY SEALED
MOTOR
• EASY TO LOAD POLYETHYLENE SPIN
BASKET WITH HAND GRIPS
• WATER DRAINS THROUGH PVC
EXTENSION TUBE DIRECTLY INTO
FLOOR DRAIN OR CONTAINER UP TO
9” HIGH - NO SPLASHING
• EASY TO LOCK, HEAVY-DUTY
CASTERS WITH BRAKES
• EASY TO CLEAN - NO HARD TO
REACH AREAS
• ONE YEAR WARRANTY, PARTS &
LABOR
MADE IN USA
MANNHART, INC.
MANNHART
651 Industrial Boulevard
Grapevine, Texas 76051
Tel (817) 421-0100
Fax (817) 421-0246
www.mannhart.com
Rev. 07/2006
5
MANNHART
MANNHART, INC.
651 Industrial Boulevard, Grapevine, Texas 76051
Phone (817) 421-0100
Fax (817) 421-0246
www.mannhart.com
MANNHART SALAD DRYER
Model SD-PS
Heavy Gauge Stainless Steel Lid, with storage hook for when lid is not in
use.
Cast Aluminum Bearing Mount keeps Salad Dryer balanced when running.
High Density Polyethylene lid, covers basket when spinning, prevents salad
from spilling.
Bushing for polyethylene lid.
T-Handle, easy to remove for cleaning lids.
High Density Polyethylene Basket with hand grips.
Cast Aluminum driver, easy to remove for cleaning or to replace.
Heavy gauge (16ga.) highly polished stainless steel tub.
Easy to reach electric timer with built in Power Cord storage. Operator does
not need to bend to turn on Salad Dryer.
Heavy-duty one-piece molded, stainless steel reinforced polyethylene base.
No openings or crevasses for food and water to get in.
PVC Drainpipe extension to floor minimizes splashing of water.
Heavy Duty Casters with brakes.
Specifications:
Height
Width
Depth
32”
24”
24”
Net Weight
Shipping Weight
75 lb.
100 lb.
Electrical:
115 Volt, 60 Hz, 1 / Fl. Amps 2.5 - 1/4 HP
Gear motor with thermal overload and permanently lubricated gear drive.
6
PARTS DIAGRAM FOR MANNHART SALAD DRYER SD–PS
SALAD DRYER SD–PS
7
MANNHART
Salad Dryers
Mannhart SD-PS
MANNHART SALAD DRYER, MODEL SD-PS PARTS LIST
8
PART #
DESCRIPTION
QUANTITY
5000-PS
SALAD DRYER LID, COMPLETE, STAINLESS STEEL
1
5001-PS
STAINLESS STEEL LID ONLY
1
5004-PS
STAINLESS STEEL SCREWS FOR BEARING MOUNT
4
5005-PS
BEARING MOUNT W/SCREWS, CAST ALUMINUM
1
5006-PS
T-HANDLE ASSEMBLY, STAINLESS STEEL
1
5007-PS
DRYER BASKET LID, POLYETHYLENE
1
5008-PS
DELRIN BUSHING FOR BASKET LID
1
5009-PS
DRYER BASKET, POLYETHYLENE
1
5013A-PS
DRAIN PIPE EXTENSION HOSE, VINYL
1
5015-PS
RUBBER GROMMET FOR ELECTRICAL CONDUIT PIPE
1
5021-PS
MOTOR WATER DEFLECTOR, STAINLESS STEEL
1
5026-PS
GEAR MOTOR - 115/60/1 - 1/4 HP
1
5026-PSA
GEAR MOTOR - 230/60/1 - 1/4 HP
1
5026-PSB
HEXAGON BOLTS W/LOCKWASHER TO FASTEN MOTOR
4
5027-PS
OCTOGONAL DRIVER FOR GEARMOTOR
1
5029-PS
ELECTRICAL CONDUIT PIPE
1
5034-PS
ELECTRICAL TIMER BOX
1
5036-PS
CABLE RELIEVE BUSHING FOR POWER CORD
1
5037-PS
FIVE MINUTE ELECTRICAL TIMER
1
5039-PS
POWER SUPPLY CORD 14/3 W/MOLDED PLUG 115/60/1
1
5039-PSE
POWER SUPPLY CORD 14/3 W/MOLDED PLUG 230/60/1
1
5042-PS
CASTERS W/POSITIVE LOCKING MECHANISM
3
5043-PS
STAINLESS STEEL BOLT FOR CASTERS (4 PER CASTER)
4
5050-PS
SALAD DRYER BODY, STAINLESS STEEL
1
Salad Dryers
MANNHART
Mannhart SD-PE / SD-PS
ELECTRICAL WIRING DIAGRAM
WHITE
BLACK
WHITE
TIMER
BLACK
POWER
SUPPLY CORD
GROUND
GROUND
GEAR MOTOR
Gear Motor: ¼ HP, 115 Volt, 60 Hz, 1 Phase, 2.8 Amps
OR
¼ HP, 230 Volt, 60 Hz, 1 Phase, 1.4 Amps
9
Salad Dryers
MANNHART
Mannhart SD-PE / SD-PS
OPERATING INSTRUCTIONS
1. Position the Mannhart Salad dryer on a
solid, flat floor surface over the floor drain or
place a two (2) gallon capacity container under
the drain tube.
6. Place loaded spin basket into salad dryer
ensuring the octagon shaped recess in the P/E
spin basket lines up with the metal octagon
driver in the salad dryer.
2. Secure machine into position by depressing
the brake pedal on each caster.
7. Place the stainless steel lid onto the salad
dryer, making sure it sits flush on top of the
stainless steel tub.
3. Remove the stainless steel lid by slowly
peeling it off on one side first for easy removal
(P/E* lid is attached to stainless lid). DO NOT
PULL OR FORCE LID OFF IN A QUICK MOTION.
Suspend the lid from the stainless steel salad
dryer tub using the hook provided on the
stainless steel lid.
4. Remove the perforated *P/E spin basket
and place in sink ( *see note below).
5. LOAD WASHED LETTUCE/ SALAD INTO
P/E SPIN BASKET TO BELOW HANDLE HOLES
ONLY.
LET EXCESS WATER DRAIN FROM
SALAD AND SPIN BASKET PRIOR TO LOADING
P/E SPIN BASKET INTO SALAD DRYER.
FILL SPIN BASKET ONLY TO BELOW
THE HANDLE HOLES. (See below)
FILL LINE
DO NOT OVERLOAD P/E SPIN BASKET.
OVERLOADING WILL CAUSE LID AND
MOTOR FAILURE.
*Note: P/E= Polyethylene
10
Note: The P/E lid attached to the inside of the
stainless steel lid is designed to hold the P/E
spin basket in center of the salad dryer. Proper
alignment will keep the salad dryer balanced
and vibration free. Overloading will prevent the
P/E lid from lining up properly with the P/E spin
basket and will cause the salad dryer to
wobble.
8. Turn the machine “ON” by rotating the knob
on the timer clockwise choosing a one-to-five
minute cycle. Generally, a two-to-three minute
cycle is sufficient to dry a full load. Machine
will turn off automatically.
9. When the timer cycle has ended, wait 10
seconds for P/E spin basket to stop rotating
before removing the lid. Remove P/E spin
basket from the machine.
10. For high volume operation, a second spin
basket is recommended. Second basket can
be filled with lettuce while the first basket is
operating inside the salad dryer.
VERY IMPORTANT!!!
***DO NOT SPRAY WATER TOWARDS THE BOTTOM
SIDE AND MOTOR AREA OF THE MANNHART SALAD
DRYER AS THIS WILL CAUSE DAMAGE TO THE GEAR
MOTOR AND ELECTRICAL PARTS.***
Salad Dryers
MANNHART
Mannhart SD-PE / SD-PS
CLEANING INSTRUCTIONS
Unplug the Mannhart Salad Dryer, wrapping
the electrical cord on bracket mounted on the
side of the tank. Position machine over the
floor drain or place drainage container under
drain pipe.
INTERIOR SURFACE OF TANK
1. Remove the remaining food debris with a
sponge.
2. Wash the interior P/E spin basket with
warm, detergent-sanitizing solution designed
to clean stainless steel surfaces that are in
contact with food.
EXTERIOR SURFACE OF TANK
1. Use a clean, damp cloth to wipe the wash
solution from surface. Allow to air dry.
2. Any commercial stainless steel polish can be
used to shine clean surfaces.
P/E SPIN BASKET AND LIDS
1. Wash in warm, detergent-sanitizing solution
designed for use with plastic materials in
contact with food.
2. Rinse in clean water. Allow to air dry.
Never steam clean the P/E spin basket or
lid.
3. Rinse with clean water. Air dry before
placing on lid.
SUGGESTED
LETTUCE / GREENS STORAGE INSTRUCTIONS
Gently pour the produce into heavy duty plastic bags or rigid plastic containers with tight fitting lids.
Place into refrigerated storage. Ideal storage temperatures range between 32 and 35 degrees
Fahrenheit.
AVOID “PACKING” LETTUCE AND OTHER DELICATE PRODUCE TIGHTLY IN P/E SPIN BASKET. Position
containers in refrigerator allowing for good air circulation around the storage container/bags. This will
promote rapid chilling.
11
MANNHART
Salad Dryers
Mannhart SD-PE / SD-PS
BASKET FILLING
INSTRUCTIONS
BEST RESULTS ARE ACHIEVED BY
FILLING BASKET 3/4 FULL!
LOAD MUST BE DISTRIBUTED
EVENLY IN BASKET!
*********************************
NEVER FILL BASKET ABOVE
HANDLE HOLES!
12
MANNHART
Salad Dryers
Mannhart SD-PE / SD-PS
IMPORTANT NOTICE!
SALAD DRYER MUST BE PLACED ON CONCRETE
SURFACE NEAR FLOOR DRAIN TO ALLOW
PROPER DRAINING.
FLOOR MATS WILL OBSTRUCT DRAINING ABILITY.
THE HEAVY WEIGHT OF THE LOADED SALAD
DRYER MAY FORCE THE CASTERS TO SINK INTO
THE FLOOR MAT, CAUSING OBSTRUCTION OF
DRAINAGE RESULTING IN WATER BUILD-UP
WHICH MAY CAUSE GEAR MOTOR FAILURE.
GEAR MOTOR FAILURE DUE TO WATER DAMAGE
IS NOT COVERED UNDER WARRANTY!
THANK YOU.
13
Salad Dryers
MANNHART
Mannhart SD-PE / SD-PS
WARRANTY INFORMATION
The end-user customer must call Mannhart directly for Warranty
Authorization prior to arranging for a service repair company.
TELEPHONE NUMBER: (817) 421-0100
99% of the time we are able to troubleshoot with the end-user over
the phone and ship the replacement part directly to the store for fast
and easy installation.
If a service repair company is required, Mannhart Inc. will authorize
the service repair company of the end-user’s choice to work on our
equipment.
The original part being replaced must be returned to Mannhart for
warranty inspection and final authorization.
Note: The complete Mannhart Warranty Information can be found
on the warranty card that is shipped with every Mannhart Salad
Dryer.
Thank you,
MANNHART, INC.
14
MANNHART
MANNHART, INC.
651 INDUSTRIAL BOULEVARD
GRAPEVINE, TEXAS 76051
TELEPHONE: (817) 421-0100
FAX: (817) 421-0246
www.mannhart.com