Alliance Laundry Systems Cabinet Hardmount SC27SN Specifications

Installation
Washer-Extractors
Cabinet Hardmount
Refer to Page 6 for Model Identification
CHM1772C
CHM1772C
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
www.alliancelaundry.com
Part No. F8208301R9
February 2015
Table of
Contents
Safety Information..............................................................................
Explanation of Safety Messages...........................................................
Important Safety Instructions ...............................................................
Safety Decals ........................................................................................
Operator Safety.....................................................................................
2
2
2
4
5
Introduction.........................................................................................
Model Identification .............................................................................
Delivery Inspection...............................................................................
Nameplate Location..............................................................................
Replacement Parts ................................................................................
Customer Service..................................................................................
6
6
10
10
12
12
Specifications and Dimensions........................................................... 13
Dimensional Clearances ....................................................................... 22
Installation...........................................................................................
Machine Foundation .............................................................................
Concrete Foundation Installation .....................................................
Machine Anchoring ..............................................................................
Direct-to-Finished-Floor Installation ...............................................
Elevated Base Frame Installation.....................................................
Mounting Bolt Hole Locations (Without Elevated Base Frames)........
Mounting Bolt Hole Locations (With Elevated Base Frames).............
Drain Connection..................................................................................
Water Connection Requirements..........................................................
Electrical Installation Requirements.....................................................
Input Power Conditioning.....................................................................
Input Voltage Requirements ............................................................
Circuit Breakers and Quick Disconnects .........................................
Connection Specifications ...............................................................
Grounding ........................................................................................
Phase Adder .....................................................................................
Thermal Overload Protector ............................................................
Steam Requirements (Steam Heat Option Only)..................................
Supply Dispensing ................................................................................
External Supplies ..................................................................................
Connection of External Liquid Supplies..........................................
23
23
25
28
28
29
31
37
41
43
44
45
46
46
46
46
47
47
53
53
54
55
Start Up................................................................................................ 56
Basket Rotation..................................................................................... 56
© Copyright 2015, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any
means without the expressed written consent of the publisher.
F8208301ENR9
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
1
Safety Information
Explanation of Safety Messages
Precautionary statements (“DANGER,” “WARNING,”
and “CAUTION”), followed by specific instructions,
are found in this manual and on machine decals. These
precautions are intended for the personal safety of the
operator, user, servicer, and those maintaining the
machine.
DANGER
DANGER indicates the presence of a
hazard that will cause severe personal
injury, death, or substantial property
damage if the danger is ignored.
WARNING
WARNING indicates the presence of a
hazard that can cause severe personal
injury, death, or substantial property
damage if the warning is ignored.
CAUTION
CAUTION indicates the presence of a
hazard that will or can cause minor
personal injury or property damage if the
caution is ignored.
Additional precautionary statements (“IMPORTANT”
and “NOTE”) are followed by specific instructions.
IMPORTANT: The word “IMPORTANT” is used
to inform the reader of specific procedures where
minor machine damage will occur if the procedure
is not followed.
NOTE: The word “NOTE” is used to communicate
installation, operation, maintenance or servicing
information that is important but not hazard
related.
Important Safety Instructions
WARNING
To reduce the risk of fire, electric shock,
serious injury or death to persons when
using your washer, follow these basic
precautions:
W023
1. Read all instructions before using the washer.
2. Install the washer according the
INSTALLATION instructions. Refer to the
GROUNDING instructions in the
INSTALLATION manual for the proper
grounding of the washer. All connections for
water, drain, electrical power and grounding must
comply with local codes and be made by licensed
personnel when required. It is recommended that
the machine be installed by qualified technicians.
3. Do not install or store the washer where it will be
exposed to water and/or weather.
4. To prevent fire and explosion, keep the area
around machine free from flammable and
combustible products. Do not add the following
substances or textiles containing traces of the
following substances to the wash water: gasoline,
kerosene, waxes, cooking oils, vegetable oils,
machine oils, dry-cleaning solvents, flammable
chemicals, thinners, or other flammable or
explosive substances. These substances give off
vapors that could ignite, explode or cause the
fabric to catch fire by itself.
5. Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been
used for two weeks or more. HYDROGEN GAS
IS EXPLOSIVE. If the hot water system has not
been used for such a period, before using a
washing machine or combination washer-dryer,
turn on all hot water faucets and let the water
flow from each for several minutes. This will
release any accumulated hydrogen gas. The gas
is flammable, do not smoke or use an open flame
during this time.
6. To reduce the risk of an electric shock or fire, DO
NOT use an extension cord or an adapter to
connect the washer to the electrical power
source.
2
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8208301ENR9
Safety Information
7. Do not allow children to play on or in the washer.
Close supervision of children is necessary when
the washer is used near children. This appliance
is not intended for use by young children or
infirm persons without supervision. Young
children should be supervised to ensure that they
do not play with the appliance. This is a safety
rule for all appliances.
8. DO NOT reach and/or climb into the tub or onto
the washer, ESPECIALLY if the wash drum is
moving. This is an imminently hazardous
situation that, if not avoided, will cause severe
personal injury or death.
9. Never operate the washer with any guards, panels
and/or parts removed or broken. DO NOT bypass
any safety devices or tamper with the controls.
10. Use washer only for its intended purpose,
washing textiles. Never wash machine parts or
automotive parts in the machine. This could
result in serious damage to the basket or tub.
11. Use only low-sudsing, no-foaming types of
commercial detergent. Be aware that hazardous
chemicals may be present. Wear hand and eye
protection when adding detergents and
chemicals. Always read and follow
manufacturer’s instructions on packages of
laundry and cleaning aids. Heed all warnings or
precautions. To reduce the risk of poisoning or
chemical burns, keep them out of the reach of
children at all times (preferably in a locked
cabinet).
12. Do not use fabric softeners or products to
eliminate static unless recommended by the
manufacturer of the fabric softener or product.
13. Always follow the fabric care instructions
supplied by the textile manufacturer.
14. Loading door MUST BE CLOSED any time the
washer is to fill, tumble or spin. DO NOT bypass
the loading door switch by permitting the washer
to operate with the loading door open. Do not
attempt to open the door until the washer has
drained and all moving parts have stopped.
15. Be aware that hot water is used to flush the
supply dispenser. Avoid opening the dispenser lid
while the machine is running.
16. Do not attach anything to the supply dispenser’s
nozzles, if applicable. The air gap must be
maintained.
18. Be sure water connections have a shut-off valve
and that fill hose connections are tight. CLOSE
the shut-off valves at the end of each wash day.
19. Keep washer in good condition. Bumping or
dropping the washer can damage safety features.
If this occurs, have washer checked by a
qualified service person.
20. DANGER: Before inspecting or servicing
machine, power supply must be turned OFF. The
servicer needs to wait for at least 3 minutes after
turning the power OFF and needs to check for
residual voltage with a voltage meter. The
inverter capacitor or EMC filter remains charged
with high voltage for some time after powering
OFF. This is an imminently hazardous situation
that, if not avoided, will cause severe personal
injury or death.
21. Do not repair or replace any part of the washer, or
attempt any servicing unless specifically
recommended in the user-maintenance
instructions or in published user-repair
instructions that the user understands and has the
skills to carry out. ALWAYS disconnect the
washer from electrical, power and water supplies
before attempting any service.
22. Disconnect the power cord by grasping the plug,
not the cord. Replace worn power cords and/or
loose plugs. If the supply cord is damaged, it
must be replaced by a special cord or assembly
available from the service agent.
23. Before the washer is removed from service or
discarded, remove the door to the washing
compartment.
24. Failure to install, maintain, and/or operate this
washer according to the manufacturer’s
instructions may result in conditions which can
produce bodily injury and/or property damage.
NOTE: The WARNINGS and IMPORTANT
SAFETY INSTRUCTIONS appearing in this
manual are not meant to cover all possible
conditions and situations that may occur. Common
sense, caution and care must be exercised when
installing, maintaining, or operating the washer.
Any problems or conditions not understood should be
reported to the dealer, distributor, service agent or the
manufacturer.
17. Do not operate the machine without the water
reuse plug or water reuse system in place, if
applicable.
F8208301ENR9
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
3
Safety Information
WARNING
CAUTION
This machine must be installed, adjusted,
and serviced by qualified electrical
maintenance personnel familiar with the
construction and operation of this type of
machinery. They must also be familiar
with the potential hazards involved.
Failure to observe this warning may result
in personal injury and/or equipment
damage, and may void the warranty.
SW004
IMPORTANT: Ensure that the recommended
clearances for inspection and maintenance are
provided. Never allow the inspection and
maintenance space to be blocked.
Be careful around the open door,
particularly when loading from a level
below the door. Impact with door edges
can cause personal injury.
SW025
WARNING
Never touch internal or external steam
pipes, connections, or components.
These surfaces can be extremely hot and
will cause severe burns. The steam must
be turned off and the pipe, connections,
and components allowed to cool before
the pipe can be touched.
SW014
WARNING
Install the machine on a level floor of
sufficient strength. Failure to do so may
result in conditions which can produce
serious injury, death and/or property
damage.
W703
Safety Decals
Safety decals appear at crucial locations on the
machine. Failure to maintain legible safety decals
could result in injury to the operator or service
technician.
To provide personal safety and keep the machine in
proper working order, follow all maintenance and
safety procedures presented in this manual. If
questions regarding safety arise, contact the
manufacturer immediately.
Use manufacturer-authorized spare parts to avoid
safety hazards.
4
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8208301ENR9
Safety Information
Operator Safety
Do not bypass any safety devices in the machine.
WARNING
WARNING
NEVER insert hands or objects into
basket until it has completely stopped.
Doing so could result in serious injury.
SW012
Operating the machine with severe out-ofbalance loads could result in personal
injury and serious equipment damage.
W728
To ensure the safety of machine operators, the
following maintenance checks must be performed
daily:
1. Prior to operating the machine, verify that all
warning signs are present and legible. Missing or
illegible signs must be replaced immediately.
Make certain that spares are available.
2. Check door interlock before starting operation of
the machine:
a. Attempt to start the machine with the door
open. The machine should not start with the
door open.
b. Close the door and start the machine. The
machine should not start with the door
unlocked.
c. Attempt to open the door while the cycle is in
progress. The door should not open.
If the door lock and interlock are not functioning
properly, disconnect power and call a service
technician.
3. Do not attempt to operate the machine if any of
the following conditions are present:
a. The door does not remain securely locked
during the entire cycle.
b. Excessively high water level is evident.
c. Machine is not connected to a properly
grounded circuit.
F8208301ENR9
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5
Introduction
Model Identification
Information in this manual is applicable to these
models:
20 POUND
Model
HCD020GD2
HCD020JD2
HCD020LD2
HCL020GD2
HCL020GN2
HCL020HDF
HCL020HN2
HCL020KD2
HCL020KDF
HCL020KDV
HCL020LD2
HCN020GC2
HCN020GD2
HCN020GE2
HCN020GN2
HCN020GX2
HCN020GY2
HCN020HC2
HCN020HCF
HCN020HD2
HCN020HN2
HCN020HNF
HCN020HY2
HCN020HYF
HCN020KC2
HCN020KCF
HCN020KCV
HCN020KD2
HCN020KDV
HCN020KDV
HCN020KEF
HCN020KEV
HCN020KY2
HCN020KYF
HCN020KYV
HCU020GC2
HCU020GD2
HCU020GE2
HCU020GL2
HCU020GN2
HCU020GX2
HCU020GY2
HCU020HC2
HCU020HN2
HCU020HNF
HCU020HX2
HCU020KCF
HCU020KCV
HCU020KE2
HCU020KEV
HCU020KL2
HCU020KY2
HCU020KYF
HCU020KYV
HCZ020GN2
HCZ020HN2
SCL020GC2
SCL020GN2
SCL020HN2
SCL020HNF
SCL020JC2
SCL020JD2
SCL020JDF
SCL020JE2
SCL020JEF
SCL020JX2
SCN020GC2
SCN020GD2
SCN020GE2
SCN020GN2
SCN020GX2
SCN020GY2
SCN020HN2
SCN020HNF
SCN020JC2
SCN020JCF
SCN020JCV
SCN020JD2
SCN020JEF
SCN020JXF
SCN020JY2
SCN020JYF
SCN020JYV
SCN020KN2
SCN020KNF
SCN020LC2
SCN020LCF
SCN020LCV
SCN020LD2
SCN020LX2
SCN020LY2
SCN020LYF
SCN020LYV
SCN020WC2
SCN020WCF
SCN020WCV
SCN020WD2
SCN020WDV
SCN020WY2
SCN020WYF
SCN020WYV
SCU020GC2
SCU020GD2
SCU020GE2
SCU020GL2
SCU020GN2
SCU020GX2
SCU020GY2
SCU202HN2
SCU020HNF
SCU020JC2
SCU020JCF
SCU020JCV
SCU020JD2
SCU020JDF
SCU020JDV
SCU020JE2
SCU020JEF
SCU020JEV
SCU020JL2
SCU020JLF
SCU020JLV
SCU020JX2
SCU020JXF
SCU020JXV
SCU020JY2
SCU020JYF
SCU020JYV
SCU020KN2
SCU020KNF
SCU020LC2
SCU020LCV
SCU020LD2
SCU020LDV
SCU020LE2
SCU020LEV
SCU020LX2
SCU020LXV
SCU020LY2
SCU020LYV
SCU020WC2
SCU020WCV
SCU020WD2
SCU020WDV
SCU020WE2
SCU020WEV
SCU020WX2
SCU020WXV
SCU020WY2
SCU020WYV
UCL020GN2
UCL020HN2
UCL020KN2
UCN020GN2
UCN020HN2
UCN020HNF
UCN020KN2
UCU020GN2
UCU020HN2
UCU020HNF
UCU020KN2
UCZ020GN2
(Continued)
6
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8208301ENR9
Introduction
(Continued)
30 POUND
Model
HCD030LD2
HCL030GN2
HCL030HDF
HCL030HN2
HCL030HNF
HCL030KD2
HCL030KDF
HCL030KDV
HCN030GC2
HCN030GD2
HCN030GE2
HCN030GN2
HCN030GX2
HCN030GY2
HCN030HC2
HCN030HCF
HCN030HD2
HCN030HN2
HCN030HNF
HCN030HY2
HCN030HYF
HCN030KC2
HCN030KCF
HCN030KCV
HCN030KD2
HCN030KDV
HCN030KEF
HCN030KY2
HCN030KYF
HCN030KYV
HCU030GC2
HCU030GD2
HCU030GE2
HCU030GL2
HCU030GN2
HCU030GX2
HCU030GY2
HCU030HC2
HCU030HN2
HCU030HNF
HCU030HX2
HCU030KCF
HCU030KCV
HCU030KE2
HCU030KEV
HCU030KY2
HCU030KYF
HCU030KYV
HCZ030GN2
SCD030GD2
SCD030LD2
SCL030GC2
SCL030GN2
SCL030HN2
SCL030HNF
SCL030JC2
SCL030JCF
SCL030JD2
SCL030JDF
SCL030JE2
SCL030JEF
SCL030JX2
SCL030JXF
SCL030JY2
SCL030KN2
SCL030KNF
SCL030KNV
SCL030LD2
SCL030LEV
SCN030GC2
SCN030GD2
SCN030GE2
SCN030GN2
SCN030GX2
SCN030GY2
SCN030HN2
SCN030HNF
SCN030JC2
SCN030JCF
SCN030JCV
SCN030JD2
SCN030JE2
SCN030JEF
SCN030JX2
SCN030JY2
SCN030JYF
SCN030JYV
SCN030KN2
SCN030KNF
SCN030LC2
SCN030LCF
SCN030LCV
SCN030LD2
SCN030LE2
SCN030LY2
SCN030LYF
SCN030LYV
SCN030WC2
SCN030WCF
SCN030WCV
SCN030WD2
SCN030WDV
SCN030WLV
SCN030WX2
SCN030WY2
SCN030WYF
SCN030WYV
SCU030GC2
SCU030GD2
SCU030GE2
SCU030GL2
SCU030GN2
SCU030GX2
SCU030GY2
SCU030HN2
SCU030HNF
SCU030JC2
SCU030JCF
SCU030JCV
SCU030JD2
SCU030JDF
SCU030JDV
SCU030JE2
SCU030JEF
SCU030JEV
SCU030JL2
SCU030JLF
SCU030JLV
SCU030JX2
SCU030JXF
SCU030JXV
SCU030JY2
SCU030JYF
SCU030JYV
SCU030KN2
SCU030KNF
SCU030LC2
SCU030LCV
SCU030LD2
SCU030LDV
SCU030LE2
SCU030LEV
SCU030LX2
SCU030LXV
SCU030LY2
SCU030LYV
SCU030WC2
SCU030WCV
SCU030WD2
SCU030WDV
SCU030WE2
SCU030WEV
SCU030WX2
SCU030WXV
SCU030WY2
SCU030WYV
UCL030GN2
UCL030HN2
UCL030HNF
UCL030KN2
UCN030GN2
UCN030HN2
UCN030HNF
UCN030KN2
UCN030KNF
UCU030GN2
UCU030HN2
UCU030HNF
UCU030KN2
UCZ030GN2
VCU030GN2
(Continued)
F8208301ENR9
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
7
Introduction
(Continued)
40 POUND
Model
HCD040LD2
HCL040GN2
HCL040HC2
HCL040HDF
HCL040HE2
HCL040HN2
HCL040KD2
HCL040KDF
HCL040KDV
HCN040GC2
HCN040GD2
HCN040GE2
HCN040GN2
HCN040GX2
HCN040GY2
HCN040HC2
HCN040HCF
HCN040HD2
HCN040HN2
HCN040HNF
HCN040HY2
HCN040HYF
HCN040KC2
HCN040KCF
HCN040KCV
HCN040KD2
HCN040KDF
HCN040KDV
HCN040KEF
HCN040KEV
HCN040KY2
HCN040KYF
HCN040KYV
HCU040GC2
HCU040GD2
HCU040GE2
HCU040GL2
HCU040GN2
HCU040GX2
HCU040GY2
HCU040HC2
HCU040HN2
HCU040HNF
HCU040HX2
HCU040KCF
HCU040KCV
HCU040KE2
HCU040KEV
HCU040KY2
HCU040KYF
HCU040KYV
SCD040GD2
SCD040LD2
SCL040GC2
SCL040GN2
SCL040HN2
SCL040HNF
SCL040JC2
SCL040JD2
SCL040JDF
SCL040JE2
SCL040JEF
SCL040JX2
SCL040JXF
SCL040JXV
SCL040KN2
SCL040KNF
SCL040KNV
SCL040LE2
SCN040GC2
SCN040GD2
SCN040GE2
SCN040GN2
SCN040GX2
SCN040GY2
SCN040HN2
SCN040HNF
SCN040JC2
SCN040JCF
SCN040JCV
SCN040JD2
SCN040JE2
SCN040JEF
SCN040JY2
SCN040JYF
SCN040JYV
SCN040KN2
SCN040KNF
SCN040KNV
SCN040LC2
SCN040LCF
SCN040LCV
SCN040LD2
SCN040LDV
SCN040LE2
SCN040LY2
SCN040LYF
SCN040LYV
SCN040WC2
SCN040WCF
SCN040WCV
SCN040WDV
SCN040WX2
SCN040WY2
SCN040WYF
SCN040WYV
SCU040GC2
SCU040GD2
SCU040GE2
SCU040GL2
SCU040GN2
SCU040GX2
SCU040GY2
SCU040HN2
SCU040HNF
SCU040JC2
SCU040JCF
SCU040JCV
SCU040JD2
SCU040JDF
SCU040JDV
SCU040JE2
SCU040JEF
SCU040JEV
SCU040JL2
SCU040JLF
SCU040JLV
SCU040JX2
SCU040JXF
SCU040JXV
SCU040JY2
SCU040JYF
SCU040JYV
SCU040KN2
SCU040KNF
SCU040KNV
SCU040LC2
SCU040LCV
SCU040LD2
SCU040LDV
SCU040LE2
SCU040LEV
SCU040LX2
SCU040LXV
SCU040LY2
SCU040LYV
SCU040WC2
SCU040WCV
SCU040WD2
SCU040WDV
SCU040WE2
SCU04WEV
SCU040WX2
SCU040WXV
SCU040WY2
SCU040WYV
UCL040GN2
UCL040HN2
UCL040HNF
UCL040KN2
UCL040KNF
UCL040KNV
UCN040GN2
UCN040HN2
UCN040HNF
UCN040KN2
UCN040KNF
UCN040KNV
UCU040GN2
UCU040HN2
UCU040HNF
UCU040KN2
UCU040KNV
VCU040GN2
(Continued)
8
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8208301ENR9
Introduction
(Continued)
60 POUND
HCD060LD2
HCL060GN2
HCL060HCF
HCL060HN2
HCL060KD2
HCL060KDF
HCL060KDV
HCN060GC2
HCN060GD2
HCN060GE2
HCN060GN2
HCN060GX2
HCN060GY2
HCN060HC2
HCN060HCF
HCN060HDF
HCN060HN2
HCN060HNF
HCN060HY2
HCN060HYF
HCN060KC2
HCN060KCF
HCN060KCV
HCN060KD2
HCN060KDF
HCN060KDV
HCN060KEV
HCN060KEF
HCN060KY2
HCN060KYF
HCN060KYV
HCU060GC2
HCU060GD2
HCU060GE2
HCU060GL2
HCU060GN2
HCU060GX2
HCU060GY2
HCU060HC2
HCU060HN2
HCU060HNF
HCU060HX2
HCU060KCF
HCU060KCV
HCU060KEV
HCU060KY2
HCU060KYF
HCU060KYV
SCD060GD2
SCD060LD2
SCL060GC2
SCL060GN2
SCL060HN2
SCL060HNF
SCL060JC2
SCL060JCF
SCL060JD2
SCL060JE2
SCL060JXF
SCL060KN2
SCL060KNV
SCL060LE2
SCN060GC2
SCN060GD2
SCN060GE2
SCN060GN2
SCN060GNF
SCN060GX2
SCN060GY2
SCN060HN2
SCN060HNF
SCN060JC2
SCN060JCF
SCN060JCV
SCN060JD2
SCN060JDF
SCN060JEF
SCN060JX2
SCN060JY2
SCN060JYF
SCN060JYV
SCN060KN2
SCN060KNF
SCN060KNV
SCN060LC2
SCN060LCF
SCN060LCV
SCN060LD2
SCN060LDV
SCN060LE2
SCN060LY2
SCN060LYF
SCN060LYV
SCN060WC2
SCN060WCF
SCN060WCV
SCN060WD2
SCN060WDV
SCN060WEV
SCN060WY2
SCN060WYF
SCN060WYV
SCU060GC2
SCU060GD2
SCU060GE2
SCU060GL2
SCU060GN2
SCU060GX2
SCU060GY2
SCU060HN2
SCU060HNF
SCU060JC2
SCU060JCF
SCU060JCV
SCU060JD2
SCU060JDF
SCU060JDV
SCU060JE2
SCU060JEF
SCU060JEV
SCU060JL2
SCU060JLF
SCU060JLV
SCU060JX2
SCU060JXF
SCU060JXV
SCU060JY2
SCU060JYF
SCU060JYV
SCU060KN2
SCU060KNF
SCU060KNV
SCU060LC2
SCU060LCV
SCU060LD2
SCU060LDV
SCU060LE2
SCU060LEV
SCU060LX2
SCU060LXV
SCU060LY2
SCU060LYV
SCU060WC2
SCU060WCV
SCU060WD2
SCU060WDV
SCU060WE2
SCU060WEV
SCU060WX2
SCU060WXV
SCU060WY2
SCU060WYV
UCL060GN2
UCL060HN2
UCL060HNF
UCL060KN2
UCL060KNF
UCL060KNV
UCN060GN2
UCN060HN2
UCN060HNF
UCN060KN2
UCN060KNF
UCN060KNV
UCU060GN2
UCU060HN2
UCU060HNF
UCU060KN2
UCU060KNV
VCU060GN2
80 POUND
HCD080LDV
HCL080HNF
HCL080KDF
HCL080KDV
HCN080GCF
HCN080GDF
HCN080GEF
HCN080GNF
HCN080GXF
HCN080GYF
HCN080HCF
HCN080HCV
HCN080HDF
HCN080HNF
HCN080HYF
HCN080HYV
HCN080KCF
HCN080KCV
HCN080KDF
HCN080KDV
HCN080KEV
HCN080KYF
HCN080KYV
HCU080GCF
HCU080GDF
HCU080GEF
HCU080GLF
HCU080GNF
HCU080GXF
HCU080GYF
HCU080HCF
HCU080HNF
HCU080HXF
HCU080KCF
HCU080KCV
HCU080KYF
HCU080KYV
SCD080LDV
SCL080GNF
SCL080HNF
SCL080KNV
SCN080GCF
SCN080GDF
SCN080GEF
SCN080GNF
SCN080GXF
SCN080GYF
SCN080HNF
SCN080JCF
SCN080JCV
SCN080JDF
SCN080JYF
SCN080JYV
SCN080KNV
SCN080LCV
SCN080LDV
SCN080LYV
SCN080WCV
SCN080WDV
SCN080WYV
SCU080GCF
SCU080GDF
SCU080GEF
SCU080GLF
SCU080GNF
SCU080GXF
SCU080GYF
SCU080HNF
SCU080JCF
SCU080JCV
SCU080JDF
SCU080JDV
SCU080JEF
SCU080JEV
SCU080JLF
SCU080JLV
SCU080JYF
SCU080JYV
SCU080JXF
SCU080JXV
SCU080KNV
SCU080LCV
SCU080LDV
SCU080LEV
SCU080LXV
SCU080LYV
SCU080WCV
SCU080WDV
SCU080WEV
SCU080WXV
SCU080WYV
UCL080GNF
UCL080HNF
UCL080KNV
UCN080GNF
UCN080HNF
UCN080KNV
UCU080GNF
UCU080HNF
UCU080KNV
VCU080GNF
125 POUND
Model
HCN125KYV
SCL125KNV
SCN125KNV
SCN125LYV
SCN125WYV
SCU125KNV
UCL125HNV
UCL125KNV
UCU125HNV
UCU125KNV
F8208301ENR9
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9
Introduction
This manual is designed as a guide to the installation
of the Cabinet Hardmount Washer-Extractor.
NOTE: All information, illustrations, and
specifications contained in this manual are based
on the latest product information available at the
time of printing. We reserve the right to make
changes at any time without notice.
Nameplate Location
The nameplate is located at the rear of the machine and
inside door. Always provide the machine’s serial
number and model number when ordering parts or
when seeking technical assistance. Refer to Figure 1.
1
Delivery Inspection
Upon delivery, visually inspect crate, protective cover,
and unit for any visible shipping damage. If the crate,
protective cover, or unit is damaged or signs of
possible damage are evident, have the carrier note the
condition on the shipping papers before the shipping
receipt is signed, or advise the carrier of the condition
as soon as it is discovered.
Remove the crate and protective cover as soon after
delivery as possible. If any damage is discovered upon
removal of the crate and/or protective cover, advise the
carrier and file a written claim immediately.
CHM2233N
1
Nameplate
Figure 1
10
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8208301ENR9
Introduction
Model Number Familiarization Guide
Sample Model Number: *CN040GC2OU1D01
*C
Product Family
N
Agency Approval
040
Washer-Extractor Capacity (pounds dry weight of laundry)
G
Type of Electrical Control
C
Actuation (C = Coin drop)
2
Washer-Extractor Speed Capability (2 = 2 speed)
O
Electrical Characteristics
U
Panel Type
1
Design Series
D
Heat Feature (D = Direct Steam)
01
Option Identification (varies from machine to machine)
* Denotes Brand
*CN040GC2OUID01
00000000000
Model No.
Serial No.
208 – 240
Hz 60
Number of wires : 3
FLA :
Circuit Breaker Size : 3 amps
Max. Load : 40
LB
18.2 KG
Voltage
Schematic :
Supply Water:
30 - 85 psi, 2 - 5.7
Phase
3
amps
BAR
EXAMPLE OF NAMEPLATE
CHM2286N
CHM2286N
Figure 2
F8208301ENR9
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
11
Introduction
Replacement Parts
If literature or replacement parts are required, contact
the source from which the machine was purchased or
contact Alliance Laundry Systems at (920) 748-3950
for the name and address of the nearest authorized
parts distributor.
Customer Service
For technical assistance, contact your local distributor
or contact:
Alliance Laundry Systems
Shepard Street
P.O. Box 990
Ripon, Wisconsin 54971-0990
U.S.A.
www.alliancelaundry.com
Phone: +1 (920) 748-3121
+32 56 41 20 54
Wevelgem, Belgium
12
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8208301ENR9
Specifications and Dimensions
2 Speed Models
Specification
20
30
40
60
Net weight, lbs. (kg)
387
(176)
489
(222)
692
(314)
812
(368)
Domestic shipping weight, lbs. (kg)
420
(191)
530
(240)
734
(333)
854
(387)
Domestic shipping volume, ft.3 (m3)
30.5
(.86)
40.75
(1.15)
50
(1.42)
64
(1.81)
Export shipping weight, lbs. (kg)
475
(215)
593
(269)
816
(370)
948
(430)
Export shipping volume, ft.3 (m3)
36.2
(1.03)
49.9
(1.41)
60
(1.70)
75.8
(2.15)
Cylinder diameter, in. (mm)
21
(533)
24
(610)
26.25
(667)
30
(762)
Cylinder depth, in. (mm)
13.75
(349)
16
(406)
20.25
(514)
22
(559)
Cylinder volume, ft.3 (l)
2.76
(78.1)
4.19
(118.6)
6.34
(180)
9.00
(255)
Perforation size, in. (mm)
0.188
(4.76)
0.188
(4.76)
0.188
(4.76)
0.188
(4.76)
Perforation open area, %
17
23
17.5
18
Weight and Shipping Information
Wash Cylinder Information
F8208301ENR9
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
13
Specifications and Dimensions
2 Speed Models (Continued)
Specification
20
30
40
60
Door opening diameter, in. (mm)
11.63
(295)
14.34
(364)
16.25
(413)
16.25
(413)
Height of door bottom above floor, in. (mm)
14.38
(365)
14
(356)
14.5
(368)
15
(381)
Height of door opening above floor, in. (mm)
17.19
(437)
17
(431)
19
(483)
18.5
(470)
400
(101)
450
(113)
510
(129)
750
(189)
No load
.06
.13
.196
.25
Sheets
.10
.14
.195
.26
Towels
.11
.16
.213
.33
1
1
1
1
Wash/reverse power, HP (kW)
0.15
(0.11)
0.24
(0.18)
0.40
(0.30)
0.55
(0.41)
High extract power, HP (kW)
0.74
(0.55)
1.34
(1.00)
1.8
(1.3)
2.7
(2.01)
Wash/reverse speed, RPM
57
49
51
44
High extract speed, RPM
528
464
491
469
Wash/reverse centrifugal force, G
0.9
0.8
0.8
0.9
High extract centrifugal force, G
80.3
72.1
78.1
85.4
Door Opening Information
Estimated Building Heat Load
HVAC load, BTU/hr. (Kcal./hr.)
Power Consumption
Average power used per cycle,
kW-hr.
Drive Train Information
Number of motors in drive train
Cylinder Speeds
Centrifugal Force Data
14
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8208301ENR9
Specifications and Dimensions
2 Speed Models (Continued)
Specification
20
30
40
60
Steam inlet connection size, NPT
N/A
N/A
1/2
1/2
Number of steam inlets
N/A
N/A
1
1
LOW
N/A
N/A
2.09
(0.84)
3.6
(0.895)
MED
N/A
N/A
2.40
(1.15)
4.4
(1.384)
HIGH
N/A
N/A
2.84
(1.48)
5.5
(1.916)
N/A
0.73
(6.9)
1.43
(12.2)
2.32
(15.4)
200V
5.4
5.4
10.8
10.8
240V
7.8
7.8
15.6
15.6
380V
6.5
6.5
13.0
13.0
415V
7.8
7.8
15.5
15.5
480V
10.4
10.4
15.6
15.6
3
3
6
6
2.6
2.6
2.6
2.6
Direct Steam Heating (Optional)
Steam required to raise bath
water temperature,
10°F (10°C), lbs. (kg)
Average steam use per cycle,
bhp (kg)
Electrical Heating (Optional)
Total electrical heating
capacity, kW
Input Voltage
Electrical heating elements
Electrical heat element size, kW
F8208301ENR9
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
15
Specifications and Dimensions
V-Speed and F-Speed Models
Specification
20
30
40
60
80
125
Net weight, lbs. (kg)
386
(175)
498
(226)
706
(321)
773
(350)
1374
(623)
2301
(1044)
Domestic shipping weight, lbs. (kg)
424
(191)
545
(245)
744
(338)
824
(373)
1461
(663)
2384
(1081)
Domestic shipping volume, ft.3 (m3)
27
(0.76)
34.4
(.98)
43.6
(1.24)
52.2
(1.48)
102.2
(2.89)
163
(4.3)
Export shipping weight, lbs. (kg)
476
(215)
588
(267)
846
(385)
1020
(463)
1573
(714)
2492
(1130)
Export shipping volume, ft.3 (m3)
36.7
(1.04)
49.5
(1.40)
65.6
(1.86)
74.7
(3.35)
118.3
(3.35)
173
(4.8)
Cylinder diameter, in. (mm)
21
(533)
24
(610)
26.25
(667)
30
(762)
36
(914)
42
(1067)
Cylinder depth, in. (mm)
13.75
(349)
16
(406)
20.25
(514)
22
(559)
22
(559)
24
(610)
Cylinder volume, ft.3 (l)
2.76
(78.1)
4.19
(118)
6.34
(180)
9.00
(255)
12.4
(354)
19.2
(544)
Perforation size, in. (mm)
0.188
(4.76)
0.188
(4.76)
0.188
(4.76)
0.188
(4.76)
0.188
(4.76)
0.188
(4.76)
Perforation open area, %
17
23
17.5
18
18
24
Door opening size, in. (mm)
11.63
(295)
14.34
(364)
16.25
(413)
16.25
(413)
18.5
(470)
20
(508)
Height of door bottom above floor,
in. (mm)
14.38
(365)
14
(356)
14.5
(368)
18.25
(445)
17.75
(451)
29
(737)
Height of door opening above floor,
in. (mm)
17.19
(437)
17
(431)
18
(457)
18.5
(470)
21.63
(549)
30.25
(768)
No load
.06
.13
.196
.25
.30
.63
Sheets
.10
.14
.195
.26
.28
.64
Towels
.11
.16
.213
.33
.34
.83
400
(101)
450
(113)
510
(129)
750
(189)
950
(239)
1200
(302)
1
1
1
1
1
1
1
(.75)
1
(.75)
2
(1.7)
3
(2.2)
5
(3.7)
7.5
(5.6)
Weight and Shipping Information
Wash Cylinder Information
Door Opening Information
Power Consumption
Average power used per cycle,
kW-hr.
Estimated Building Heat Load
HVAC load, BTU/hr. (Kcal./hr.)
Drive Train Information
Number of motors in drive train
Drive motor power, hp (kW)
16
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8208301ENR9
Specifications and Dimensions
V-Speed and F-Speed Models (Continued)
Specification
20
30
40
60
80
125
Gentle wash/reverse speed, RPM
29
27
26
26
22
26
Wash/reverse speed, RPM
52
52
46
43
40
37
Distribution speed, RPM
92
92
82
77
70
65
Low extract speed, RPM
366
366
328
307
280
260
Medium extract speed, RPM (Not
available on Electronic Control models)
534
534
478
447
408
378
High extract speed, RPM
686
686
613
574
524
485
Gentle wash centrifugal force, G
0.25
0.25
0.25
0.25
0.25
0.43
Wash/reverse centrifugal force, G
0.8
0.8
0.8
0.8
0.8
0.8
Distribution centrifugal force, G
2.5
2.5
2.5
2.5
2.5
2.6
Extract Speed 1, G
80
80
80
80
80
80
Extract Speed 2, G
100
100
100
100
100
100
Extract Speed 3 (V-Speed only), G
120
120
120
120
120
120
Extract Speed 4 (V-Speed only), G
140
140
140
140
140
140
Steam inlet connection size, NPT
N/A
N/A
1/2
1/2
1/2
3/4
Number of steam inlets
N/A
N/A
1
1
1
1
LOW
N/A
N/A
2.09
(0.94)
3.6
(1.63)
2.58
(1.17)
3.64
(1.65)
MED
N/A
N/A
2.40
(1.09)
4.4
(2.00)
4.65
(2.11)
5.17
(2.35)
HIGH
N/A
N/A
2.84
(1.29)
5.5
(2.50)
5.79
(2.63)
7.78
(3.52)
N/A
0.73
(6.9)
1.43
(12.2)
2.32
(15.4)
1.34
(20.9)
1.14
(31.45)
5.4
10.8
10.8
21.7
N/A
Cylinder Speeds
Centrifugal Force Data
Direct Steam Heating (Optional)
Steam required to raise bath
water temperature
10°F (10°C), lbs. (kg)
Average steam use per cycle, bhp (kg)
Electrical Heating
Total electrical heating capacity, Input Voltage
kW
200V
5.4
Electrical heating elements
Electrical heat element size, kW
F8208301ENR9
240V
7.8
7.8
15.6
15.6
31.2
N/A
380V
6.5
6.5
13.0
13.0
19.6
34.4
415V
7.8
7.8
15.5
15.5
23.3
41
480V
10.4
10.4
15.6
15.6
31.2
54.8
3
3
3
9
12
12
2.6
2.6
5.2
2.6
2.6
4.2
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
17
Specifications and Dimensions
NOTE: The dimensions shown are for planning
purposes only. They are approximate and subject
to normal manufacturing tolerances. If exact
dimensions are required for construction purposes,
contact the distributor or manufacturer. We
reserve the right to make changes at any time
without notice.
2
C
A
3
H
G
F
1
4
5
P
R
Q
B
L
M
N
D
I
E
6
O
K
J
CHM2278N
20, 30, 40, 60 and 80 POUND CAPACITY MACHINES
CHM2278N
1
2
3
Supply Dispenser
Input Power Block Compartment
Hot Water Inlet
4
5
6
Cold Water Inlet
Vacuum Breaker
Drain Outlet
Figure 3
18
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8208301ENR9
Specifications and Dimensions
Machine Capacity Dimensions
Dimensions
20
30
40
60
80
A
35.15 in.
(893 m)
38.03 in.
(966 mm)
40.31 in.
(1024 mm)
43.31 in.
(1100 mm)
51.87 in.
(1317 mm)
B
34.52 in.
(877 mm)
37.46 in.
(951 mm)
39.71 in.
(1009 mm)
42.4 in.
(1077 mm)
48.68 in.
(1236 mm)
C
1.81 in.
(46 mm)
1.73 in.
(44 mm)
2.97 in.
(75 mm)
2.42 in.
(61 mm)
2.71 in.
(69 mm)
D
4.5 in.
(114 mm)
4.5 in.
(114 mm)
4.81 in.
(122 mm)
4.69 in.
(119 mm)
5.71 in.
(145 mm)
Standard
5.88 in.
(149 mm)
5.88 in.
(149 mm)
6.35 in.
(161 mm)
5.5 in.
(140 mm)
6.38 in.
(162 mm)
Electric Heat
5.88 in.
(149 mm)
5.88 in.
(149 mm)
6.03 in.
(153 mm)
6.27 in.
(159 mm)
7.15 in.
(182 mm)
F
8.82 in.
(224 mm)
8.82.in.
(224 mm)
8.82.in.
(224 mm)
8.82.in.
(224 mm)
8.82 in.
(224 mm)
G
15.10 in.
(384 mm)
15.19 in.
(386 mm)
15.15 in.
(385 mm)
19.85 in.
(504 mm)
21.62 in.
(549 mm)
H
15.6 in.
(396 mm)
15.6 in.
(396 mm)
15.65 in.
(398 mm)
20.35 in.
(517 mm)
26.12 in.
(663 mm)
I
1.58 in.
(40 mm)
1.18 in.
(30 mm)
1.47 in.
(37 mm)
1.34 in.
(34 mm)
0.97 in.
(25 mm)
J
30.21 in.
(767 mm)
34.57 in.
(878 mm)
39.72 in.
(1009 mm)
42.54 in.
(1081 mm)
51.5 in.
(1308 mm)
K
25.5 in.
(648 mm)
30.42 in.
(773 mm)
35.28 in.
(896 mm)
38.23 in.
(971 mm)
47.52 in
(1207 mm).
L
23.01 in.
(584 mm)
24 in.
(610 mm)
26 in.
(660 mm)
26.38 in.
(670 mm)
30.91 in.
(785 mm)
M
17 in.
(432 mm)
17 in.
(432 mm)
17.74 in.
(451 mm)
18.12 in.
(460 mm)
20.77 in.
(528 mm)
N
14.38 in.
(365 mm)
14 in.
(356 mm)
14.56 in.
(370 mm)
14.94 in.
(379 mm)
17.91 in.
(455 mm)
O
26 in.
(660 mm)
29 in.
(737 mm)
30.63 in.
(778 mm)
34.06 in.
(865 mm)
41.5 in.
(1054 mm)
P
1.5 in.
(38 mm)
1.5 in.
(38 mm)
1.5 in.
(38 mm)
1.5 in.
(38 mm)
1.5 in.
(38 mm)
Q
42 in.
(1067 mm)
44.95 in.
(1142 mm)
47.20 in.
(1199 mm)
49.89 in.
(1267 mm)
56.16 in.
(1426 mm)
R
9 in.
(229 mm)
9 in.
(229 mm)
9 in.
(229 mm)
9 in.
(229 mm)
9 in.
(229 mm)
E
F8208301ENR9
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
19
Specifications and Dimensions
F
2
D
4
E
5
6
7
8
P
1
3
A
G
Q
H
L
M
B
C
I
9
N
O
J
K
125 POUND CAPACITY MACHINES
CHM2279N
CHM2279N
1
2
3
4
5
Dry Chemical Dispenser (Optional)
Input Power Block Compartment
Fans
Valve Panel
Cold Water Inlet
6
7
8
9
Hot Water Inlet
Liquid Chemical Inlet
Steam Inlet (Optional)
Drain Outlet
Figure 4
Machine Capacity Dimensions for 125 Pound Models through 1/31/11
20
A
78.8 in. (2002 mm)
J
61.28 in. (1557 mm)
B
14.62 in. (371 mm)
K
70.81 in. (1799 mm)
C
6.27 in. (159 mm)
L
50.2 in. (1275 mm)
D
29.56 in. (751 mm)
M
38.96 in. (990 mm)
E
41.28 in. (1049 mm)
N
35.74 in. (908 mm)
F
51.26 in. (1302 mm)
O
60 in. (1524 mm)
G
75.15 in. (1909 mm)
P
9.92 in (252 mm)
H
83.4 in. (2118 mm)
Q
88.09 in. (2237 mm)
I
2.86 in. (73 mm)
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8208301ENR9
Specifications and Dimensions
F
2
D
4
E
5
6
7
8
P
1
3
A
G
Q
H
L
M
B
C
I
9
N
O
J
K
CHM2345N
125 POUND CAPACITY MACHINES
CHM2345N
1
Dry Chemical Dispenser (Optional on OPL
Models)
Input Power Block Compartment
Fans
Valve Panel
2
3
4
5
6
7
8
9
Cold Water Inlet
Hot Water Inlet
Liquid Chemical Inlet
Steam Inlet (Optional)
Drain Outlet
Figure 5
Machine Capacity Dimensions for 125 Pound Models starting 2/1/11
A
63.04 in. (1601 mm)
J
49.02 in. (1245 mm)
B
11.69 in. (297 mm)
K
56.06 in. (1424 mm)
C
5.01 in. (127 mm)
L
40.16 in. (1020 mm)
D
23.65 in. (601 mm)
M
30.16 in. (766 mm)
E
33.03 in. (839 mm)
N
28.28 in. (718 mm)
F
39.28 in. (998 mm)
O
48 in. (1219 mm)
G
60.21 in. (1529 mm)
P
7.94 in (202 mm)
H
65.77 in. (1671 mm)
Q
70.47 in. (1790 mm)
I
2.29 in. (58 mm)
F8208301ENR9
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
21
Specifications and Dimensions
Dimensional Clearances
C
FRONT
A
B
CHM2280N
CHM2280N
Figure 6
Dimensions
A
B
Recommended
C
Minimum
22
Machine Capacity Dimensional Clearances
20
30
40
60
2 in.
2 in.
2 in.
2 in.
(51 mm)
(51 mm)
(51 mm)
(51 mm)
.5 in.
.5 in.
.5 in.
.5 in.
(12.5 mm)
(12.5 mm)
(12.5 mm)
(12.5 mm)
24 in.
24 in.
24 in.
24 in.
(610 mm)
(610 mm)
(610 mm)
(610 mm)
12 in.
12 in.
12 in.
12 in.
(305 mm)
(305 mm)
(305 mm)
(305 mm)
80
6 in.
(152 mm)
.5 in.
(12.5 mm)
24 in.
(610 mm)
18 in.
(457 mm)
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
125
24 in.
(600 mm)
.5 in.
(12.5 mm)
36 in.
(914 mm)
24 in.
(610 mm)
F8208301ENR9
Installation
Machine Foundation
NOTE: Do not mount on wooden floors, tile floors,
above ground level, or over basements or crawl
spaces because of the high extract speed and the
G-forces exerted.
Thoroughness of detail must be stressed with all
foundation work to ensure a stable unit installation,
eliminating possibilities of excessive vibration during
the extract cycle.
The floor and foundation must be minimum 4000 psi
reinforced concrete set firmly in clean, compacted fill
dirt.
The machine must be anchored to a smooth, level
surface so that the entire base of the machine is
supported and rests on the mounting surface. (Do not
support the machine on only four points.)
Grouting is required.
An elevated foundation must not exceed 8 inches
(203 mm).
Refer to Table 1 for foundation and anchoring
requirements.
Machine Foundation Requirements
Anchoring
Bolt
Diameter
Size
(minimum)
Foundation
Thickness
(minimum)
Mounting
Bolt
depth
Installation
Foundation
Method(s)
Anchoring
Method(s)
Requirement*
2 Speed and F-Speed
(20-60 Models)
4 in.
(102 mm)
2.75 in.
(70 mm)
Direct-to-floor, elevated
base frame, or concrete
foundation
Expansion bolt
or Epoxy bolt
5/8 in.
Variable-Speed
(20-60 Models)
6 in.
(152 mm)
2.75 in.
(70 mm)
Direct-to-floor, elevated
base frame or concrete
foundation
Epoxy bolt
5/8 in.
80 Models
9 in.
(229 mm)
3.25 in.
(83 mm)
Direct-to-floor or
concrete foundation
Epoxy bolt or
rebar frame
3/4 in.
125 Models
12 in.
(304 mm)
3.25 in.
(83 mm)
Models
VariableSpeed
* Recommend SAE 495 Grade 5 or higher strength bolts.
Table 1
WARNING
To reduce the risk of fire, this appliance
must be bolted to an uncovered concrete
floor.
W731
F8208301ENR9
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
23
Installation
Refer to Table 2 and Table 3 for static and dynamic
loads on the floor or foundation.
Floor Load Data, 2 Speed Models
Specification
20
30
40
60
Static floor load, lbs. (kN)
449
(1.99)
622
(2.76)
903
(4.0)
1099
(4.9)
Static pressure, lbs.-ft.2 (kN-m2)
97.8
(4.68)
101
(4.84)
118
(5.65)
120
(5.75)
Dynamic load, lbs. (kN)
374
(1.66)
495
(2.2)
898
(3.99)
1404
(6.3)
Dynamic pressure,
lbs.-ft.2 (kN-m2)
165.3
(7.91)
169
(8.09)
216
(10.3)
253
(12.11)
Dynamic load frequency, Hz
8.8
7.7
8.2
7.8
Maximum moment about
machine base, lbs.-ft. (kN-m)
714
(0.97)
989
(1.34)
1926
(2.61)
3086
(4.2)
Maximum vertical load, lbs. (kN)
759
(3.37)
1038
(4.62)
1653
(7.4)
2322
(10.3)
Table 2
Floor Load Data, Variable-Speed Models
Specification
20
30
40
60
80
125
Static floor load, lbs. (kN)
482
(2.14)
624
(2.78)
923
(4.11)
1061
(4.22)
1738
(7.73)
2839
(12.6)
Static pressure, lbs.-ft.2 (kN-m2)
105
(5.02)
102
(4.87)
121
(5.78)
116
(5.54)
126.9
(6.07)
177.5
(8.5)
Dynamic load, lbs. (kN)
532
(2.37)
767
(3.41)
1049
(4.67)
1514
(6.73)
3310
(14.72)
4364
(19.4)
Dynamic pressure, lbs.-ft.2
(kN-m2)
207
(9.98)
214
(10.22)
238
(11.37)
261
(12.47)
350.5
(16.78)
431.5
(20.6)
Dynamic load frequency, Hz
11.5
10.7
10.2
9.6
8.95
8.1
Maximum moment about
machine base, lbs.-ft. (kN-m)
1016
(1.38)
1535
(2.08)
2252
(3.05)
3328
(4.51)
8482
(11.5)
14547
(19.7)
Maximum vertical load, lbs. (kN)
950
(4.23)
1313
(5.84)
1824
(8.11)
2394
(10.65)
4799
(21.35)
6904
(30.7)
Table 3
24
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8208301ENR9
Installation
Concrete Foundation Installation
A concrete foundation pad may be constructed to
elevate the machines. The concrete foundation pad
must be poured, reinforced with rebar and tied to the
existing floor with reinforcing bars. Refer to Figure 7,
Figure 8 or Figure 9 for a typical concrete foundation
pad installation.
WARNING
1. Verify that the floor meets the requirements given
in the Machine Foundation section.
2. Excavate the floor to a depth of approximately
9 inches (230 mm) below the floor surface,
making certain that the sides of the hole slope
outwards from top to bottom. The bottom of the
hole should be 6 inches (152 mm) larger all
around than the top.
3. Wet the hole well and brush the bottom and sides
with cement grout.
To reduce the risk of fire, this appliance
must be bolted to an uncovered concrete
floor.
W731
B
C
A
D
E
CHM2281N
20, 30, 40 AND 60 MODELS
CHM2281N
A
B
C
Pad height must not exceed 8 in. (203 mm)
above existing floor
.5 in. (13 mm) minimum
4 in. (102 mm) minimum
D
E
4 in. (102 mm) minimum
(2 and F-Speed Models)
6 in. (152 mm) minimum (V-Speed Models)
Concrete reinforcing bar
Figure 7
F8208301ENR9
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
25
Installation
4. Use rebar or other appropriate material to ensure
that the concrete foundation will be sufficiently
connected to the existing floor.
5. If desired, prepare a form for the above-ground
portion of the foundation and fill form and
excavation with concrete to join the foundation.
Verify that top of foundation is level. The height
of the foundation must not exceed 8 inches
(203 mm).
NOTE: When using any anchoring bolts, allow 1.5
inches (38 mm) to extend above the surface of the
concrete. Refer to the Machine Anchoring section.
7. Allow concrete to dry and cure before machine is
placed into service.
6. Use the mounting bolt layout to properly position
the mounting bolts in the wet concrete.
26
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8208301ENR9
Installation
A
B
B
LENGTH FOR ONE MACHINE
B
C
D
COMPACTED FILL DIRT 18 in. (457 mm) DEPTH
COMPACTED FILL DIRT 18 in. (457 mm) DEPTH
CHM2282N
80 MODELS
CHM2282N
A
B
9 in. (229 mm)
6 in. (152 mm)
C
D
47.5 in. (1207 mm)
4 ft. 6 in. (1372 mm)
Figure 8
A
B
A
C
LENGTH FOR ONE MACHINE
A
D
COMPACTED FILL DIRT 24 in. (609 mm) DEPTH
COMPACTED FILL DIRT 24 in. (609 mm) DEPTH
CHM2283N
125 MODELS
CHM2283N
A
B
12 in. (305 mm)
6 in. (152 mm)
C
D
48 in. (1219 mm)
6 ft. (1829 mm)
Figure 9
F8208301ENR9
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
27
Installation
Machine Anchoring
Before anchoring the machine, refer to Table 4 to
determine the appropriate method of anchoring for the
machine.
NOTE: Improper installation may void the
warranty. Consult the manufacturer or distributor
before varying from a procedure.
Direct-to-Finished-Floor Installation
Installing With Expansion Bolts for
2 Speed Models
NOTE: Expansion bolts are not suitable for
variable-speed machine installations.
1. Verify the floor meets the requirements given in
the Machine Foundation section.
13. Position washers and nuts on bolts and finger
tighten nuts to machine base.
14. Before grout sets completely, make a drain
opening in the grouting at the rear center of the
machine with a stiff piece of wire. This opening
should be approximately .5 inch (13 mm) wide to
allow any surface water build-up under the base
of the machine to drain away. Do not omit this
step.
15. Allow machine grout to set, but not cure.
16. Remove the spacers carefully, allowing the
machine to settle into the grout.
17. Tighten the nuts by even increments – one after
the other using the specified torque – until all are
tightened evenly and the machine is fastened
securely to the floor. Refer to Table 4.
2. Mounting surface should be level and machine
must be properly grouted.
3. Use the base of the machine as a template by
positioning the machine in the desired location
and marking the pre-drilled mounting holes on
the floor. Mounting Bolt templates are available
through Alliance Laundry Systems.
A
B
4. Refer to Figure 10 and Table 4 to set the drill
depth gauge.
5. Drill the holes to the set depth. Refer to Table 4.
C
6. Use compressed air or a squeeze bulb to clean out
debris from each hole.
CHM
CHM2285N
7. Fill half the hole depth with an industry-accepted
adhesive anchoring system.
Figure 10
8. Insert expansion bolt until it reaches the bottom
of the hole and 1.5 inches (38 mm) of the bolt
extends above the surface.
9. Allow adhesive around bolt to cure properly.
NOTE: Select the proper size and strength anchor
system. Follow the manufacturer’s installation
instructions and recommended cure times.
10. Position machine over anchoring bolts.
11. Raise and level the machine .5 inch (13 mm) off
the floor on three points, using spacers such as
nut fasteners.
Anchor Specifications
(refer to Figure 10)
Torque
(ft.- lbs.)
Models
A
B
(minimum)
C
20-60
5/8 in.
2.75 in.
(69.9 mm)
.625 in.
(15.9 mm)
90
(ft.-lbs.)
80-125
3/4 in.
3.25 in.
(82.6 mm)
.75 in.
(19 mm)
175
(ft.-lbs.)
Table 4
12. Fill the space between the machine base and the
floor with a good quality non-shrinking
machinery grout to ensure a stable installation.
Grout completely under all frame members.
28
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8208301ENR9
Installation
The completed expansion bolt installation is shown in
Figure 11.
NOTE: Check and retighten the nuts after five to
ten days of operation and every three months
thereafter.
1
3
2
4
5
1.5 in.
(38.1 mm)
Refer to
Table 4
6
CHM2284
CHM2284N
1
2
3
4
5
6
Washer
Locknut
Machine Base or Base Frame
Machinery Grout
Adhesive
Expansion Bolt
H035I
Figure 12
Figure 11
Elevated Base Frame Installation
Factory-built elevated steel base frames are designed
to meet the specifications of the 20-60 2 speed,
F-speed and V-speed model washer-extractors only.
Refer to Figure 12. The spacing between two
machines provided by an elevated base is .38 inch
(9.5 mm) in 20, 30 and 60 pound models and .25 inch
(6.3 mm) in 40 pound models.
F8208301ENR9
Installing With Elevated Base Frame
1. Verify the floor meets the requirements given in
the Machine Foundation section.
2. Use the elevated base frame as a template by
positioning the frame in the desired location and
marking the pre-drilled mounting holes on the
floor.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
29
Installation
3. Refer to Figure 10 and Table 4 to set the drill
depth gauge.
4. Drill the holes to the set depth. Refer to Table 4.
5. Use compressed air or a squeeze bulb to remove
debris from each hole.
6. Fill half the hole depth with an industry accepted
adhesive anchoring system.
7. Insert bolt until it reaches the bottom of the hole
and 1.5 inches (38 mm) of the bolt extends above
the base frame. Refer to Figure 11.
8. Allow adhesive around the bolt to cure properly.
9. Position base frame over anchoring bolts.
10. Raise and level the base frame .5 inch (13 mm)
off the floor on three points, using spacers such
as nut fasteners.
11. Fill the space between the base frame and the
floor with a good quality non-shrinking
machinery grout to ensure a stable installation.
Grout completely under all frame members.
12. Position washers and locknuts on bolts and finger
tighten nuts to base frame.
13. Before grout sets completely, make a drain
opening in the grouting at the rear of the base
frame with a stiff piece of wire. This opening
should be approximately .5 inch (13 mm) wide to
allow any surface water build-up under the base
of the machine to drain away. This drain opening
must not be near frame mounting bolts. Do not
omit this step.
17. Position the machine over the base frame, aligning
the mounting holes on the machine with the
corresponding holes on the frame.
18. Install a bolt, lockwasher, and nut in each
mounting hole. Use 5/8 inch – 18 x 2.00 grade 5
mounting bolts with 5/8 inch – 18 grade B nuts
and 5/8 inch lockwashers.
19. Hand tighten each nut.
20. Tighten the two rear nuts two turns.
21. Tighten the two front nuts two turns.
22. On 30, 40 and 60 models, tighten the two middle
nuts firmly.
23. Tighten the two front nuts firmly; tighten the two
rear nuts firmly.
NOTE: Check and retighten the locknuts after five
to ten days of operation and every three months
thereafter.
NOTE: For 80 and 125 pound models, a
bolt-locator fixture or rebar frame is available as
an option. This is designed to be embedded in
concrete. Refer to Figure 13.
IMPORTANT: Do not install any 80 or 125
machines on an elevated base frame.
1
2
3
14. Allow machine grout to set, but not cure.
15. Remove the spacers carefully, allowing the base
frame to settle into the wet grout.
4
16. Tighten nuts by even increments – one after the
other using the specified torque – until all are
tightened evenly and the base frame is fastened
securely to the floor. Refer to Table 4.
P035I
1
2
3
4
Machine Base
Mounting Bolt Threads
Grouting
Bolt-Locator Fixture or Rebar Frame
Figure 13
30
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8208301ENR9
Installation
Mounting Bolt Hole Locations (Without Elevated Base Frames)
26 in.
(660 mm)
2.67 in.
(68 mm)
2.67 in.
(68 mm)
25-44 in.
(646 mm)
23.94 in.
(608 mm)
20.66 in.
(525 mm)
14.31 in.
(363 mm)
31.75 in.
(806 mm)
0.75 in.
(19 mm)
25.22 in.
(641 mm)
20.88 in.
(530 mm)
2.56 in.
(65 mm)
20 Models
Front of Front Panel
2.56 in.
(65 mm)
CHM2224N
Figure 14
IMPORTANT: Drawing is not to scale.
F8208301ENR9
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
31
Installation
Mounting Bolt Hole Locations (Without Elevated Base Frames)
29 in.
(737 mm)
2.75 in.
(70 mm)
23.5 in.
(597 mm)
28.94 in.
(735 mm)
2.75 in.
(70 mm)
30.5 in.
(775 mm)
18.44 in.
(468 mm)
37.52 in.
(953 mm)
30.02 in.
(762 mm)
0.75 in.
(19 mm)
Front of Frame
23.88 in.
(607 mm)
30 Models
2.56 in.
(65 mm)
Front of Front Panel
2.56 in.
(65 mm)
CHM2063N
Figure 15
IMPORTANT: Drawing is not to scale.
32
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8208301ENR9
Installation
32.5 in.
(826 mm)
Mounting Bolt Hole Locations (Without Elevated Base Frames)
23.63 in.
(600 mm)
3.5 in.
(89 mm)
20 in.
(508 mm)
36 in.
(914 mm)
41.63 in.
(1057 mm)
31.88 in.
(810 mm)
Front of Frame
0.75 in.
(19 mm)
0.75 in.
(19 mm)
1.75 in.
(45 mm)
26 in.
(660 mm)
Front of Front Panel
30.63 in.
(778 mm)
40 Models
2.32 in.
(59 mm)
CHM206
CHM2067N
Figure 16
IMPORTANT: Drawing is not to scale.
F8208301ENR9
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
33
Installation
Mounting Bolt Hole Locations (Without Elevated Base Frames)
34.06 in.
(865 mm)
27.5 in.
(700 mm)
3.28 in.
(83 mm)
36 in.
(914 mm)
3.28 in.
(83 mm)
24.07 in.
(611 mm)
37.5 in.
(953 mm)
46.88 in.
(1191 mm)
37.44 in.
(951 mm)
0.75 in.
(19 mm)
30 in.
(760 mm)
1.25 in.
(32 mm)
Front of Front Panel
2.03 in.
(52 mm)
60 Models
2.03 in.
(52 mm)
CH
CHM2065N
Figure 17
IMPORTANT: Drawing is not to scale.
34
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8208301ENR9
Installation
Mounting Bolt Hole Locations (Without Elevated Base Frames)
1 in.
(25 mm)
33.5 in.
(851 mm)
A
A
4 in.
(102 mm)
4 in.
(102 mm)
B
B
5 in.
(127 mm)
56.5 in.
(1435 mm)
5 in.
(127 mm)
A
11 in.
(279 mm)
A
B
B
47.5 in.
(1207 mm)
17 in.
(432 mm)
9.5 in.
(241 mm)
40 in.
(1016 mm)
0.75 in.
(19 mm)
0.75 in.
(19 mm)
28.5 in.
(724 mm)
31.5 in.
(800 mm)
25 in.
(635 mm)
43.22 in.
(1098 mm)
4 in.
(102 mm)
4 in.
(102 mm)
B
A
1 in.
(25 mm)
A
B
33.5 in.
(851 mm)
Front of Front Panel
41.5 in.
(1054 mm)
80 Models*
CHM2334
CHM2334N
*For close mounting, use mounting bolt pattern labeled “A”; for standard mounting, use “B.”
Figure 18
IMPORTANT: Drawing is not to scale.
F8208301ENR9
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
35
Installation
Mounting Bolt Hole Locations (Without Elevated Base Frames)
0.75 in.
(19 mm)
0.75 in.
(19 mm)
46.5 in.
(1181 mm)
48 in.
(1219 mm)
10 in.
(254 mm)
61.5 in.
(1562 mm)
15 in.
(381 mm)
55.47 in.
(1409 mm)
48.94 in.
(1243 mm)
15.25 in.
(388 mm)
23.25 in.
(591 mm)
23.25 in.
(591 mm)
Front of Front Panel
0.75 in.
(19 mm)
48 in.
(1219 mm)
125 Models
CHM2069N
Figure 19
IMPORTANT: Drawing is not to scale.
36
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8208301ENR9
Installation
Mounting Bolt Hole Locations (With Elevated Base Frames)
26.4 in.
(670 mm)
2.87 in.
(73 mm)
2.87 in.
(73 mm)
23.94 in.
(608 mm)
26.2 in.
(665 mm)
20.66 in.
(525 mm)
14.31 in.
(363 mm)
31.75 in.
(806 mm)
1.13 in.
(29 mm)
25.22 in.
(640 mm)
20.88 in.
(530 mm)
2.75 in.
(70 mm)
Front of Front Panel
2.75 in.
(70 mm)
20 Models
CHM2070N
Figure 20
IMPORTANT: Drawing is not to scale.
F8208301ENR9
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
37
Installation
Mounting Bolt Hole Locations (With Elevated Base Frames)
29.4 in.
(747 mm)
2.94 in.
(75 mm)
2.94 in.
(75 mm)
31.2 in.
(792 mm)
28.94 in.
(735 mm)
23.5 in.
(597 mm)
18.44 in.
(468 mm)
37.52 in.
(953 mm)
30.02 in.
(762 mm)
1.13 in.
(29 mm)
23.88 in.
(607 mm)
Front of Front Panel
2.75 in.
(70 mm)
2.75 in.
(70 mm)
30 Models
CHM2072N
Figure 21
IMPORTANT: Drawing is not to scale.
38
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8208301ENR9
Installation
Mounting Bolt Hole Locations (With Elevated Base Frames)
3.62 in.
(92 mm)
32.5 in.
(826 mm)
23.63 in.
(600 mm)
20 in.
(508 mm)
31.88 in.
(810 mm)
36 in.
(914 mm)
41.63 in.
(1057 mm)
26 in.
(660 mm)
2.38 in.
(61 mm)
30.88 in.
(784 mm)
Front of Front Panel
40 Models
2.44 in.
(62 mm)
CHM2074N
Figure 22
IMPORTANT: Drawing is not to scale.
F8208301ENR9
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39
Installation
Mounting Bolt Hole Locations (With Elevated Base Frames)
34.5 in.
(876 mm)
36 in.
(914 mm)
27.5 in.
(700 mm)
46.88 in.
(1191 mm)
38.9 in.
(988 mm)
3.47 in.
(88 mm)
24 in.
(610 mm)
37.44 in.
(951 mm)
2.13 in.
(54 mm)
3.47 in.
(88 mm)
30 in.
(762 mm)
Front of Front Panel
2.22 in.
(56 mm)
2.22 in.
(56 mm)
60 Models
CHM2076N
Figure 23
IMPORTANT: Drawing is not to scale.
40
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8208301ENR9
Installation
Drain Connection
Figure 24 and Figure 25 show typical drain trough and
drain line installations.
Connect the drain outlet to a vented drain system using
only a flexible connection. The drain system must be
vented to prevent an air lock or siphoning.
Use the supplied black rubber adapter and clamps to
transition from the machine drain outlet to the 2 inches
schedule 40 PVC plumbing (20 and 30 models) and
the 3 inches schedule 40 PVC plumbing (40, 60, 80
and 125 models).
If proper drain size is not available or practical, a surge
tank is required. A surge tank along with a sump pump
should be used when gravity drainage is not possible,
such as in below-ground-level installations.
DRAIN TROUGH
3
2
4
7
1
5
CHM2058N
CHM2058N
6
CHM2058N
1
2
3
4
Drain Hose
Drain Valve
Overflow Hose
Drain Tee
5
6
7
Floor
Open Drain Trough
1 in. Minimum Gap
Figure 24
DRAIN LINE
4
5*
3
2
1
CHM2335N
6
CHM2335N
1
Drain Hose
2
Drain Valve
3
Drain Tee
* Drain line must be vented to meet local plumbing codes.
4
5
6
Overflow Hose
Vent Pipe*
Trap (as required by local codes)
Figure 25
F8208301ENR9
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
41
Installation
Before any deviation from specified installation
procedures is attempted, the customer or installer
should contact the distributor.
Refer to Table 5 for capacity-specific drain
information.
NOTE: Installation of additional machines will
require larger drain connections. Refer to Table 6.
IMPORTANT: Increasing the drain hose length,
installing elbows, or causing bends will decrease
drain flow rates and increase drain times,
impairing machine performance.
Drain Information
Drain connection size,
OD
20
30
40
60
80
125
2 in.
(51 mm)
2 in.
(51 mm)
3 in.*
(76 mm)
3 in.*
(76 mm)
3 in.*
(76 mm)
3.5 in.*
(89 mm)
1
1
1
1
1
1
20 gal/min
(76 l/min)
25 gal/min
(95 l/min)
45 gal/min
(170 l/min)
55 gal/min
(208 l/min)
50 gal/min
(189 l/min)
70 gal/min
(265 l/min)
1.8 ft.3
(51 l)
2.5 ft.3
(71 l)
4.52 ft.3
(128 l)
4.52 ft.3
(128 l)
5.9 ft.3
(167 l)
13 ft.3
(368 l)
Number of drain outlets
Drain flow capacity
Recommended
drain pit size
* Also works with 3 in. OD PVC pipe if connected to inside of drain tee connector.
Table 5
Drain Line Sizing
Minimum Drain ID
Model
Number of Machines
1
2
3
4
5
20
2 in. (51 mm)
3 in. (76 mm)
3 in. (76 mm)
4 in. (102 mm)
4 in. (102 mm)
30
2 in. (51 mm)
3 in. (76 mm)
3 in. (76 mm)
4 in. (102 mm)
4 in. (102 mm)
40
3 in. (76 mm)
4 in. (102 mm)
4 in. (102 mm)
4 in. (102 mm)
6 in. (152 mm)
60
3 in. (76 mm)
4 in. (102 mm)
4 in. (102 mm)
4 in. (102 mm)
6 in. (152 mm)
80, 125
4 in. (102 mm)
6 in. (152 mm)
6 in. (152 mm)
8 in. (203 mm)
8 in. (203 mm)
Table 6
42
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8208301ENR9
Installation
Water Connection Requirements
Connections should be supplied by a hot and a cold
water line of at least the sizes shown in Table 8.
Installation of additional machines will require
proportionately larger water lines.
Suitable air cushions should be installed in supply
lines to prevent “hammering.” Refer to Figure 26.
2
To connect water service to a machine with rubber
hoses, use the following procedure:
1. Before installing hoses, flush the building’s water
system at the machine connection valves for at
least 2 minutes.
1
2. Check filters in the machine’s inlet hoses for
proper fit and cleanliness before connecting.
3. Hang hoses in a large loop; do not allow them to
kink.
If additional hose lengths are needed, use flexible
hoses with screen filters.
MW008J
MW008J
Cabinet Hardmount
Water Supply Information
Water Inlet Connection size,
in. (mm)
3/4
(19)
Thread Size
11.5
Number of water inlets
2
Recommended pressure,
psi (bar)
30-85
(2-5.7)
Inlet flow capacity,
gal-min (l-min) (80 psi)
C20-C80: 12 (45)
C125: 50 (189)
Table 7
Model
20 – 80
Water Supply Faucets
Air Cushions (Risers)
Figure 26
WARNING
To prevent personal injury, avoid contact
with inlet water temperatures higher than
125° Fahrenheit (51° Celsius) and hot
surfaces.
W748
Water Supply Line Sizing
125
1
2
Number
of
Machines
Supply Line Size
Main
Hot/Cold
1
.75 in. (19 mm)
.75 in. (19 mm)
2
1 in. (25 mm)
.75 in. (19 mm)
3
1.25 in. (32 mm)
1 in. (25 mm)
4
1.5 in. (38 mm)
1 in. (25 mm)
1
1.5 in. (38 mm)
1 in. (25 mm)
2
2 in. (50 mm)
1.5 in. (38 mm)
3
2 in. (50 mm)
2 in. (50 mm)
4
2.5 in. (70 mm)
2 in. (50 mm)
Alliance Laundry Systems, LLC ranges of front
loading commercial clothes washing machines have
solenoid valves at the inlets. The water supply to the
washing machines is supplied with an AB air gap
between the soap tray and the drum. The soap tray is
certified to meet ASSE 1055 requirements for a
chemical dispenser. Minimum and maximum working
pressure 1.4 bar and 8.3 bar. The machines are
supplied with approved inlet hoses with a maximum
inlet dimension of 12.6 mm (ID).
NOTE: This machine has a fluid category 5
backflow prevention device built in between the
soap tray and drum.
Table 8
F8208301ENR9
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
43
Installation
Electrical Installation Requirements
IMPORTANT: Electrical ratings are subject to
change. Refer to serial decal for electrical ratings
information specific to your machine.
Make sure the correct transformer jumper (208 Volt or
240 Volt) is in place. Refer to the “optional” Electrical
Service Connection label located on the back of the
machine near the electrical service input for machine
electrical requirements. Refer to Figure 27.
DANGER
1
Hazardous Voltage. Will cause shock,
burn or death. Allow machine power to
remain off for three minutes prior to
working in and around AC inverter drive.
W735
WARNING
Dangerous voltages are present inside
the machine. Only qualified personnel
should attempt adjustments and
troubleshooting. Disconnect power from
the machine before removing any cover
and guards, and before attempting any
service procedures.
W736
WARNING
CHM2287N
1
Electrical Service Connection Label
Figure 27
Hazardous Voltage. Can cause shock,
burn or death. Verify that a ground wire
from a proven earth ground is connected
to the lug near the input power block on
this machine.
Machines equipped with an AC inverter drive require
a clean power supply, free from voltage spikes and
surges. Use voltage monitor to check incoming power.
The customer’s local power company may provide
such a monitor.
W360
Electrical connections are made at the rear of the
machine. The machine must be connected to the
proper electrical supply shown on the identification
plate attached to the rear of the machine, using copper
conductors only.
IMPORTANT: Alliance Laundry Systems
warranty does not cover components that fail as a
result of improper input voltage.
44
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8208301ENR9
Installation
Input Power Conditioning
IMPORTANT: Only one device per branch circuit
is required. It should be mounted closest to the
branch and sized to handle the total current of the
branch circuit.
The drive is suitable for direct connection to input
power within the rated voltage of the drive. Listed in
Table 9 are certain input power conditions which may
cause component damage or reduction in product life.
If any of the conditions exist, as described in Table 9,
install one of the devices listed under the heading
Corrective Action on the line side of the drive.
Input Power Condition
Corrective Action
Low Line impedance (less than 1% line reactance)
Greater than 120 kVA supply transformer
Line has power factor correction capacitors
Line has frequent power interruptions
•
•
Install Line Reactor
or Isolation Transformer
•
•
Install Line Reactor
or Isolation Transformer
•
•
Remove MOV jumper to ground.
or Install Isolation Transformer with grounded
secondary if necessary
•
Install Line Reactor
Line has intermittent noise spikes in excess of 6000V (lightning)
Phase to ground voltage exceeds 125% of normal line to line voltage
Ungrounded distribution system
240V open delta configuration (stinger leg)*
* For drives applied on an open delta with a middle phase grounded neutral system, the phase opposite the phase that is tapped in the middle
to the neutral or earth is referred to as the “stinger leg,” “high leg,” “red leg,” etc. This leg should be identified throughout the system with
red or orange tape on the wire at each connection point. The stinger leg should be connected to the center Phase B on the reactor.
Table 9
F8208301ENR9
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
45
Installation
Input Voltage Requirements
Connection Specifications
For voltages above or below listed specifications,
contact your power company or local electrician.
IMPORTANT: Connection must be made by a
qualified electrician using wiring diagram provided
with machine, or according to accepted European
standards for CE-approved equipment.
If machine is intended for four-wire service, a neutral
leg must be provided by power company.
If a delta supply system is used on a four-wire model,
connect high leg to L3.
IMPORTANT: Improper connections will result in
equipment damage and will void warranty.
DANGER
Never touch terminals or components of
the AC inverter drive unless power is
disconnected for three minutes.
W737
DANGER
Hazardous Rotation Speed. Will cause
serious injury when controlling AC
inverter drive with a parameter unit,
safety features are bypassed allowing
basket to rotate at high speeds with the
door open. Place large sign on front of
machine to warn people of imminent
danger.
W361
Circuit Breakers and Quick Disconnects
Single-phase machines require a single-phase inversetime circuit breaker. Three-phase machines and
variable-speed machines require a separate, threephase inverse-time circuit breaker to prevent damage
to the motor by disconnecting all legs if one should be
lost accidentally. Check the nameplate decal on the
back of the machine. Refer to Table 10 through
in this section for model-specific circuit breaker
requirements.
Connect machine to an individual branch circuit not
shared with lighting or other equipment. Shield
connection in a liquid-tight or approved flexible
conduit. Copper conductors of correct size must be
installed in accordance with National Electric Code
(NEC) or other applicable codes.
Use wire sizes indicated in the Electrical Specifications
chart for runs up to 50 feet (15 m). Use next larger size
for runs of 50 to 100 feet (15 to 30 m). Use two sizes
larger for runs greater than 100 feet (30 m).
Grounding
For personal safety and proper operation, the machine
must be grounded in accordance with state and local
codes. If such codes are not available, grounding must
conform to the National Electric Code, article 250
(current edition). The ground connection must be
made to a proven earth ground, not to conduit or water
pipes.
WARNING
Electrically heated machines DO NOT
require dual power sources. Do not
connect customer power or customer
load to the Internal Load Distribution
terminal block. Refer to the machine
electrical schematic for details.
W759
IMPORTANT: All quick disconnects should
comply with the above specifications. DO NOT use
fuses instead of circuit breakers.
46
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8208301ENR9
Installation
Phase Adder
2
L1
1
L2
IMPORTANT: Do not use a phase adder on any
machine.
L3
Thermal Overload Protector
SERVICE
GROUND
Two speed machines have thermal overload protectors
in drive motor windings. For variable-speed machines,
the AC drive provides overload protection for the
drive motor.
CHASIS
3
TB1
PHM
MACHINES WITH ELECTRIC HEAT
PHM700N
1
Grounding Lug: Connect to proven earth
ground
Customer Input Power Terminals
Internal Load Distribution - DO NOT connect
customer power source or load.
2
3
Figure 28
1
SERVICE
GROUND
2
CHASIS
L1
L2
L3
TB1
P
MACHINES WITHOUT ELECTRIC HEAT
PHM721N
1
2
Grounding Lug: Connect to proven earth
ground
Customer Input Power Terminals
Figure 29
Machines can be converted for lower voltage
operation and/or 50 Hz operation. Refer to conversion
label by serial plate for details.
F8208301ENR9
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
47
Installation
Electrical Specifications
20 Pound Capacity Models
Voltage Designation
Standard
Electric Heat
AWG
mm2
Circuit
Breaker
Full Load
Amps
mm2
AWG
Circuit
Breaker
Full Load
Amps
Wire
Phase
Cycle
Voltage
Code
14
15
14
2.5
16
20
12
4.0
10
6
10
6
14
2.5
2 Speed Models
B
120
60
1
2
16
20
12
4.0
C
380 – 415
50
3
4
4
15
14
2.5
F
440 – 480
60
3
3
4
15
14
2.5
J
200
50
3
3
5
15
14
2.5
O
208 – 240
60
3
3
5
15
14
2.5
Y
208 – 240
60
1
2
8
15
14
2.5
N/A
N/A
23
30
N/A
Variable-Speed Models
Q
200 – 240
50/60
3
3
4
15
14
2.5
21
R
(through
7/6/10)
380 – 480
50/60
3
3
4
15
14
2.5
N/A
N
(starting
7/7/10)
440 – 480
60
3
3
4
15
14
2.5
N/A
P
(starting
7/7/10)
380 – 415
50
3
3
4
15
14
2.5
X
200 – 240
50/60
1/3
2/3
6/4
15
14
2.5
14
30
15
N/A
NOTE: Wire sizes shown are for copper, THHN, 90°C conductor per NEC article 310.
Table 10
48
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8208301ENR9
Installation
Electrical Specifications
30 Pound Capacity Models
Voltage Designation
Standard
Electric Heat
mm2
Full Load
Amps
Circuit
Breaker
AWG
mm2
14
2.5
15
20
12
4.0
F
440 – 480
60
3
3
4
15
14
2.5
16
20
12
4.0
J
200
50
3
3
7
15
14
2.5
O
208 – 240
60
3
3
7
15
14
2.5
10
6.0
Y
208 – 240
60
1
2
10
20
12
4.0
10
6.0
14
2.5
Code
AWG
15
Circuit
Breaker
4
Full Load
Amps
4
Wire
3
Phase
50
Cycle
380 – 415
Voltage
C
2 Speed Models
N/A
25
30
N/A
Variable-Speed Models
Q
200 – 240
50/60
3
3
5
15
14
2.5
22
R
(through
7/6/10)
380 – 480
50/60
3
3
4
15
14
2.5
N/A
N
(starting
7/7/10)
440 – 480
60
3
3
4
15
14
2.5
N/A
P
(starting
7/7/10)
380 – 415
50/60
3
3
4
15
14
2.5
X
200 – 240
50/60
1/3
2/3
7/5
15
14
2.5
14
30
15
N/A
NOTE: Wire sizes shown are for copper, THHN, 90°C conductor per NEC article 310.
Table 11
F8208301ENR9
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
49
Installation
Electrical Specifications
40 Pound Capacity Models
Voltage Designation
Standard
Electric Heat
mm2
Full Load
Amps
Circuit
Breaker
AWG
mm2
2.5
27
30
10
6.0
F
440 – 480
60
3
3
5
15
14
2.5
24
30
10
6.0
J
200
50
3
3
7
20
12
4.0
O
208 – 240
60
3
3
7
20
12
4.0
8
10.0
Y
208 – 240
60
1
2
14
30
10
6.0
AWG
14
Circuit
Breaker
15
Full Load
Amps
5
Wire
4
Phase
3
Cycle
50
Voltage
380 – 415
Code
C
2 Speed Models
N/A
45
50
N/A
Variable-Speed Models
R
(through
7/6/10)
380 – 480
50/60
3
3
6
15
14
2.5
23
30
10
6.0
N
(starting
7/7/10)
440 – 480
60
3
3
5
15
14
2.5
22
30
10
6.0
P
(starting
7/7/10)
380 – 415
50
3
3
5
15
14
2.5
22
30
10
6.0
Q
200 – 240
50/60
3
3
6
15
14
2.5
42
50
8
10.0
X
200 – 240
50/60
1/3
2/3
10/6
15
14
2.5
N/A
NOTE: Wire sizes shown are for copper, THHN, 90°C conductor per NEC article 310.
Table 12
50
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8208301ENR9
Installation
Electrical Specifications
60 Pound Capacity Models
Voltage Designation
Standard
Electric Heat
Full Load
Amps
Circuit
Breaker
AWG
mm2
2.5
27
30
10
6.0
F
440-480
60
3
3
5
15
14
2.5
24
30
10
6.0
J
200
50
3
3
10
20
12
4.0
O
208-240
60
3
3
10
20
12
4.0
48
50
8
10.0
Code
mm2
14
AWG
15
Circuit
Breaker
5
Full Load
Amps
4
Wire
3
Phase
50
Cycle
380-415
Voltage
C
2 Speed and Fixed-Speed Models
N/A
Variable-Speed Models
R
(through
7/6/10)
380-480
50/60
3
3
6
15
14
2.5
23
30
10
6.0
N
(starting
7/7/10)
440 – 480
60
3
3
6
15
14
2.5
24
30
10
6.0
P
(starting
7/7/10)
380 – 415
50
3
3
6
15
14
2.5
24
30
10
6.0
Q
200-240
50/60
3
3
8
15
14
2.5
43
50
8
10.0
X
200-240
50/60
1/3
2/3
11/8
15
14
2.5
N/A
NOTE: Wire sizes shown are for copper, THHN, 90°C conductor per NEC article 310.
Table 13
F8208301ENR9
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
51
Installation
Electrical Specifications
80 Pound Capacity Models
Voltage Designation
Standard
Electric Heat
mm2
Full Load
Amps
Circuit
Breaker
AWG
mm2
14
2.5
40
50
8
10.0
N
440 – 480
(starting
7/7/10)
60
3
3
8
15
14
2.5
40
50
8
10.0
P
380 – 415
(starting
7/7/10)
50
3
3
8
15
14
2.5
40
50
8
10.0
82
90
3
25.0
AWG
Wire
Cycle
Circuit
Breaker
15
Full Load
Amps
8
Phase
3
Voltage
3
Code
R
380 – 480 50/60
(through
7/6/10)
Variable-Speed Models
Q
200 – 240 50/60
3
3
11
15
14
2.5
X
200 – 240 50/60
1/3
2/3
16/11
20/15
12/14
4/2.5
N/A
NOTE: Wire sizes shown are for copper, THHN, 90°C conductor per NEC article 310.
Table 14
Electrical Specifications
125 Pound Capacity Models
Voltage Designation
Standard
Electric Heat
mm2
3
3
10
15
14
2.5
N
(starting
7/7/10)
440 – 480
60
3
3
10
15
14
2.5
65
70
4
25.0
P
(starting
7/7/10)
380 – 415
50
3
3
10
15
14
2.5
65
70
4
25.0
Q
200 – 240
50/60
3
3
11
15
14
2.5
mm2
50/60
AWG
380 – 480
Wire
AWG
Circuit
Breaker
Full Load
Amps
Circuit
Breaker
Full Load
Amps
Phase
Cycle
Voltage
Code
R
(through
7/6/10)
Variable-Speed Models
N/A
N/A
NOTE: Wire sizes shown are for copper, THHN, 90°C conductor per NEC article 310.
Table 15
52
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8208301ENR9
Installation
Steam Requirements
(Steam Heat Option Only)
Supply Dispensing
WARNING
WARNING
Hot Surfaces. Will cause severe burns.
Turn steam off and allow steam pipes,
connections and components to cool
before touching.
W505
For machines equipped with optional steam heat,
install piping in accordance with approved commercial
steam practices. Steam requirements are shown in
Table 16.
Dangerous Chemicals. May damage eyes
and skin. Wear eye and hand protection
when handling chemicals; always avoid
direct contact with raw chemicals. Read
the manufacturer’s directions for
accidental contact before handling
chemicals. Ensure an eye-rinse facility
and an emergency shower are within easy
reach. Check at regular intervals for
chemical leaks.
W363
Steam Supply Information
Steam inlet
connection size
Supply Dispensing
40 – 80 pound
1/2 in. (13 mm)
125 pound
3/4 in. (19 mm)
Number of steam inlets
1
Recommended pressure
30 – 80 psi
(2.0 – 5.4 bar)
Maximum pressure
80 psi
(5.4 bar)
Table 16
IMPORTANT: Failure to install the customer
supplied steam filter may void the warranty.
Capacities
20 – 80
125
4
0 or 5
(optional)
5
5
3/8 in.
(8 mm)
5/8 in.
(15.9 mm)
Number of supply
compartments
Number of external
liquid supply
connections (OPL only)
Liquid supply
connection size
Table 17
IMPORTANT: Undiluted chemical dripping can
damage the machine. All chemical injection supply
dispenser pumps and dispenser tubing should be
mounted below the washer’s injection point. Loops
do not prevent drips if these instructions are not
followed.
IMPORTANT: Failure to follow these instructions
could damage the machine and void the warranty.
F8208301ENR9
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53
Installation
External Supplies
1
For proper communication between the washerextractor and an external chemical supply system, it is
important for the low-voltage signal power to be
connected properly. The included wiring diagram
(F8133502) shows several different options for safe
and correct wiring of this interface.
EXTERNAL DISPENSER CONNECTIONS
ES 1
ES 3
ES 4
1. Use the Internal 24VAC 300 Control
Transformer (Recommended by Alliance
Laundry Systems)
There are 3 terminals necessary for this
connection option. Terminal “24VAC COM” is
used to connect 1 side of the internal control
transformer to the external dispenser input
signals common. The second terminal is used to
connect the other side of the control transformer
to the washer-extractor output signals common
through a red jumper wire between “24VAC” and
“RELAY COM”. Do not use the transformer
terminals if an external power supply is used.
54
RELAY COM
Supply 1
External
Dispensing
System
RELAY
COM
24VAC COM
RED
24VAC
The preferred method for connecting the wiring from
the external chemical supply system to the washerextractor is to use the 300mA power of the washerextractor’s 24VAC control transformer, which is
intended strictly for this purpose. Other voltage and
current options are available, but require some wiring
changes and must be provided with an external power
source. Under no circumstances should the highvoltage machine supply connections or source be used
for the communication wiring.
Basically, wash-cycle signals are provided to the
external chemical supply equipment and a “wait for
the next step” signal can be received from the supply
equipment. Communication wiring connections,
which include a single row of identified terminal
blocks, can be found under a service panel at the upper
back of the machine.
EXAMPLE FOR EXTERNAL
DISPENSER CONNECTION
ES 2
24VAC COM
Internal
Supply
300mA Max
JUMPER FOR INTERNAL
24 VAC SUPPLY
CONNECTED TO RELAY
COM. (REMOVE IF NOT
WIRING TO INTERNAL
24 VAC SUPPLY
STEP 1: Insert screwdriver & press down
to open cage clamp.
STEP 2: Insert Wire
2
Wire Size 28-16AWG
0.08-1.5mm
8.5mm
Strip Length
3
4
CHM2336N
CHM2336N
1
2
3
4
Relay Com
Red Jumper Wire
24 VAC
Transformer
Figure 30
2. Use an External AC Power Source (Not
Provided by Alliance Laundry Systems)
NOTE: Power for external supplies must not be
derived from the high-voltage main power
connection point.
The external power must supply power of
240VAC or less and be protected at 3 Amps or
less. Remove the red jumper wire installed by the
factory between “24VAC” and “RELAY COM”.
Connect 1 side of the external power to the
“RELAY COM” and the other to the external
dispenser input signals common.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8208301ENR9
Installation
125 Pound OPL Models
(With Optional Dispenser)
CAUTION
Do not attempt to increase fuse rating or
alter wiring of external chemical supply
terminal strip in such as way that may
conflict with the suggested methods
provided on the Optional External Supply
Wiring Diagram.
W699
Connection of External Liquid Supplies
20 – 80 Pound OPL Models
1. Facing the rear of the machine, locate the five
3/8 inch supply hose connections found on the
right-hand side of the valve panel. Refer to
Figure 31.
Refer to Figure 32.
1. Remove plugs from base. Plugs are assembled
inside tubing ring.
2. Install strain reliefs with the seal nuts.
3. Insert tubes through base. Do not remove dry
supply cups. Tube should extend into plastic cup,
with exception of softener tube, which should be
routed to outside of cup.
4. Tighten seal nut to prevent tubing from escaping
assembly.
IMPORTANT: Increasing fuse rating may cause
damage to washer-extractor’s circuitry.
IMPORTANT: Any injection system pump that
requires anything other than 24VAC must be
powered by a separate external power source.
20-80 Pound Models
Consult chemical injection supply system instructions
for operational details.
C VALVE PANEL – REAR VIEW
1
CHM2237N
1
CHM2237N
1
External Supply Hose Opening
2
Figure 31
3
2. Drill through the five plastic holes on the valve
panel for the external supply hoses as needed.
3. Remove plastic debris.
4
4. Attach the external supply hoses to the ports at
each of the drilled holes.
5. Secure with proper clamps.
NOTE: Do not attempt to make chemical injection
supply pump electrical connections to points other
than those provided specifically for that purpose by
the factory.
Consult the supply vendor instructions for operational
details about supply injections.
5
PHM2001N
CHM2001N
1
2
3
4
5
Strain Relief for Liquid Chemical Supply
Lines
Supply Dispenser Lid
Four Way Water Valve
Dry Supply Cups
Supply Dispenser
Figure 32
F8208301ENR9
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
55
Start Up
Basket Rotation
Check that basket rotation is counterclockwise in the
extract step.
1. If rotation is not counterclockwise, disconnect
power to machine.
2. For 2 speed models, have a qualified electrician
use the wiring diagram supplied with the
machine to determine which input power leads
should be switched.
3. For V-speed models, have a qualified electrician
reverse any two motor leads at the AC terminal
block.
56
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8208301ENR9