Canon PIXMA MP470 User`s guide

Start Here
Easy Setup Instructions
Photo All-in-One
Important
When cleaning the exterior of the machine, use a soft cloth to wipe it gently. For details, refer to “Cleaning Your Machine” in the Quick Start Guide.
1 Prepare the Machine
aUnpack the Machine.
2 Install the FINE Cartridges
fPlug the power cord in the back of the machine and connect the
Confirm the included items against the illustration printed on the lid of the
packing box.
A USB cable is necessary to connect the machine with your computer.
Important
When moving the machine, carry the machine at both ends as shown below. Do
not lift the machine by grasping the Paper Support Extension.
other end to the wall outlet.
aRemove the Black FINE Cartridge from its box.
dPush up the FINE Cartridge until it clicks into place.
Important
For correct machine operation, make sure the FINE Cartridge is securely inserted.
Document Cover
Click
Power Cord
Important
• Make sure that the Document Cover is closed.
• Do NOT connect the USB cable at this stage.
gOpen the Operation Panel, then press the ON/OFF button to turn
on the machine. The machine will initialize. Wait until the Power
lamp stops flashing and remains lit green.
bRemove the protective tape gently.
Protective Tape
bPlace the machine on a flat and horizontal surface, and do not
place any objects in front of the machine.
Remove all the shipping tapes and protective material on the outside of the
machine. Then open the Paper Output Tray.
eRepeat the procedure for the Color FINE Cartridge, inserting it
into the right slot C .
Electrical Contacts
cLift the Scanning Unit (Printer Cover), and pull the Scanning Unit
Support down into place.
Scanning Unit (Printer Cover)
hUse the { or } button on the Operation Panel to select the
Print Head Nozzles
language for the LCD, then press the OK button.
•
•
•
•
(1) Press the { or } button
to select the language.
dRemove the protective material on the right side.
(2) Press the OK button.
Important
If an unintended language is displayed on the LCD, press the Back button to return
to the Language selection screen.
Once the message “Set the ink cartridge.” appears, go to i.
iLift the Scanning Unit (Printer Cover), and pull the Scanning
Unit Support down into place. The FINE Cartridge Holder
automatically moves to the left.
jWrite down the serial number located inside of the machine. You
will need this to register your product.
Important
Do not touch the electrical contacts or Print Head Nozzles on a FINE Cartridge.
The machine may not print out properly if you touch it.
Do not drop or shake FINE Cartridges as this may cause the ink to leak out and
stain your clothes and hands.
Do not reattach the protective tape once you have removed it.
Be careful not to stain your hands or surrounding work area with ink on the
removed protective tape.
fLift the Scanning Unit (Printer Cover) slightly to set the Scanning
Unit Support back to its original position, and then gently close
the Scanning Unit (Printer Cover).
cInsert the Black FINE Cartridge slightly slanted into the left slot B .
Make sure that the procedure for installing the FINE Cartridges is displayed on
the LCD and the FINE Cartridge Holder has moved to the left.
FINE Cartridge Holder
Important
Once you have installed the FINE Cartridges, the message “Processing... Please
wait momentarily.” is displayed on the LCD. Wait until the copy standby screen is
displayed before proceeding. It takes about one minute.
Protective Material
Caution
Before turning on the machine, remove all of the shipping tapes.
eLift the Scanning Unit (Printer Cover) slightly to set the Scanning
Unit Support back to its original position, and then gently close
the Scanning Unit (Printer Cover).
Serial Number
Hardware setup is now complete.
Next, turn over and install the software.
Macintosh® Software Installation
Note
• The screens below refer to Windows Vista™ operating system Ultimate Edition
(hereafter referred to as “Windows Vista”) installation.
Screens may vary depending on the operating system you are using.
• Log into a user account with the administrator privilege.
• Before installing the software, disable all anti-virus programs and automatically
loading programs.
• A message asking for your confirmation to restart your computer may appear
during the installation process. If this message is displayed, follow the on-screen
instructions and click OK.
The installation resumes from where it left off when your computer has been
restarted.
aBe sure to TURN THE MACHINE OFF before continuing.
(1) Press the ON/OFF button.
(2) Make sure that the Power lamp stops flashing.
bTurn the computer on and start Windows.
Important
If the Found New Hardware or Found New Hardware Wizard screen appears
automatically, remove the USB cable connected to your computer. Click Cancel
to quit the screen. In Windows Vista, the screen may close automatically when
the USB cable is unplugged. Then turn off the machine and proceed from step
c to install the software.
M
ac
W
in
in
do
to
w
s
sh
Windows® Software Installation
gWhen the list of software to install appears, confirm the
contents, click Install.
Note
Move the cursor over items to display explanations of each application.
hRead the License Agreement carefully and click Yes. The
software installation screen may appear during the installation
process. Follow the on-screen instructions to install the
software.
iWhen the Printer Connection screen appears, connect one
end of the USB cable to the computer and the other to the
machine, then TURN THE MACHINE ON. The MP Drivers will
begin identifying the printer port being used.
Note
• Since Mac® OS 9, Mac OS X Classic environments, or Mac OS X v.10.2.7 or earlier
are not supported, do not connect the machine to these.
• The screens below refer to Mac OS X v.10.4.x installation. Screens may vary
depending on the operating system you are using.
• Log on as an Administrator.
• Before installing the software, disable all anti-virus programs and automatically
loading programs.
iWhen the Setup Complete screen appears, click Next.
aConnect one end of the USB cable to the computer and the
other to the machine.
Note
Make sure the machine is turned on.
Important
If you cannot go to the next procedure after three minutes, refer to
“Troubleshooting” instructions in the User’s Guide on-screen manual.
jWhen the User Registration screen appears, click Next.
Note
To register later, click Cancel and go to Step k. After software installation is
complete, double-click
on the desktop.
Follow on-screen instructions to register your product. You will need your
product serial number, which is located on the inside of the machine. See
Step 1- j on the front page.
kWhen the Installation completed successfully screen
appears, click Restart.
USB
USB
→
To Computer
bTurn on your Mac and insert the Setup CD-ROM.
cInsert the Setup CD-ROM. The setup program should run
automatically.
In Windows Vista, go to Step d. In Windows XP and Windows 2000, go to
Step f.
jWhen the Print Head Alignment Recommended screen
appears, click Next.
kWhen the Setup Complete screen appears, click Next.
Note
If the CD-ROM folder does not open automatically, double-click the CD-ROM icon
on the desktop.
cDouble-click the Setup icon.
dWhen the Authenticate screen appears, enter your
administrator name and password. Click OK.
If you do not know your administrator name or password, click
, then follow the on-screen instructions.
dIf the AutoPlay screen appears, click Run Msetup4.exe.
eWhen the main menu appears, click Easy Install.
The MP Drivers, On-screen Manuals, and application software are installed
automatically.
lWhen the User Registration screen appears, click Next.
eIf the User Account Control screen appears, click Continue.
If the same screen reappears in subsequent steps, click
Continue.
Note
To register later, click Cancel and go to Step m. After software installation is
complete, double-click
on the desktop.
Follow on-screen instructions to register your product. You will need your
product serial number, which is located on the inside of the machine. See
Step 1- j on the front page.
mWhen the PIXMA Extended Survey Program screen
fWhen the main menu appears, click Easy Install.
The MP Drivers, On-screen Manuals, and application software are installed
automatically.
appears, confirm the message. We would appreciate it if you
would take part in this program regarding the use of Canon
printers. If you can agree, click Agree.
nWhen the Installation completed successfully screen
appears, click Exit.
If Restart is displayed, make sure that the Restart the system now
(recommended) check box is selected, then click Restart.
Note
If you want to select particular items to install, click Custom Install and follow the onscreen instructions to proceed with the installation.
Note
If straight lines are misaligned or print quality is not satisfactory after installing the MP
Drivers, you may need to align the Print Head. Refer to “Aligning the Print Head” in the
Quick Start Guide.
The system is restarted automatically.
When using Mac OS X v.10.2.8 to v.10.3.3:
Restarting the computer while connected to the machine may cause the
machine not to be detected. To resolve this, either unplug the USB cable
then plug it back in again, or turn the machine off then back on again.
Note
• When using Mac OS X v.10.2.8 to v.10.3.x, before using the Operation Panel on
the machine to save originals scanned to the computer, it is necessary to select
MP Navigator EX 1.0 or MP Navigator EX 1 as the launch application on Image
Capture under Applications. For details, refer to “Scanning Images” in the User’s
Guide on-screen manual.
• If straight lines are misaligned or print quality is not satisfactory after installing the
MP Drivers, you may need to align the Print Head. Refer to “Aligning the Print Head”
in the Quick Start Guide.
Software installation is now complete.
Note
If you want to select particular items to install, click Custom Install and follow the onscreen instructions to proceed with the installation.
fWhen the list of software to install appears, confirm the
contents, then click Install.
Note
Move the cursor over items to display explanations of each application.
gRead the License Agreement carefully and click Yes. The
software installation screen may appear during the installation
process. Follow the on-screen instructions to install the
software.
hWhen the Print Head Alignment Recommended screen
appears, click Next.
Software installation is now complete.
Part no. QT5-1005-V01 © 2007 Canon Inc. “Microsoft” is a registered trademark of Microsoft Corporation. “Windows” is a trademark of Microsoft Corporation, registered in the U.S. and other countries. “Windows Vista” is a trademark of Microsoft Corporation. “Macintosh” and “Mac” are trademarks of Apple Inc., registered in the U.S. and other countries.
XXXXXXXX
PRINTED IN VIETNAM