R-209EK
SUPPLEMENTAL SERVICE MANUAL
S4111R209EPK/
MICROWAVE OVEN
MODEL
ON
DEF.
EXPRESS
DEFROST
TO ADJUST
LBS.
POPCORN
QUANTITY
TOUCH
BAKED
POTATOES
FROZEN
ENTREES
BEVERAG
Power
Level
Stop
Clear
E
R-209EK
QTY. CHECK
MINUTE
PLUS
SAME PAD
AGAIN
FRESH
VEGETABL
ES
In the interest of user-safety the oven should be restored to its original
condition and only parts identical to those specified should be used.
WARNING TO SERVICE PERSONNEL: Microwave ovens contain circuitry capable of producing very high voltage and
current, contact with following parts may result in a severe,
possibly fatal, electrical shock. (High Voltage Capacitor, High
Voltage Power Transformer, Magnetron, High Voltage Rectifier
Assembly, High Voltage Harness etc..)
DINNER
PLATE
ROLLS
MUFFINS
Timer
Clock
START
This is a supplemental Service Manual for Model R-209EK. This model is quite similar to base
model R-220EW. Use this supplemental manual together with the Base Model Service Manual
(Refer No. is S0101R220EPW/) for complete operation, service information, etc..
TABLE OF CONTENTS
Page
PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO
AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY ................... INSIDE FRONT COVER
BEFORE SERVICING ...................................................................................................... INSIDE FRONT COVER
WARNING TO SERVICE PERSONNEL ................................................................................................................ 1
MICROWAVE MEASUREMENT PROCEDURE ................................................................................................... 2
FOREWORD AND WARNING ............................................................................................................................... 3
PRODUCT DESCRIPTION .................................................................................................................................... 4
TEST PROCEDURE .............................................................................................................................................. 6
PICTORIAL DIAGRAM .......................................................................................................................................... 7
CONTROL PANEL CIRCUIT ................................................................................................................................. 8
PARTS LIST .......................................................................................................................................................... 9
PACKING AND ACCESSORIES ......................................................................................................................... 13
This document has been published to be used for after
sales service only.
The contents are subject to change without notice.
SHARP CORPORATION
15
R-209EK
PRECAUTIONS TO BE OBSERVED BEFORE AND
DURING SERVICING TO AVOID POSSIBLE
EXPOSURE TO EXCESSIVE MICROWAVE
ENERGY
(a) Do not operate or allow the oven to be operated with the door open.
(b) Make the following safety checks on all ovens to be serviced before activating the magnetron or other
microwave source, and make repairs as necessary: (1) interlock operation, (2) proper door closing, (3)
seal and sealing surfaces (arcing, wear, and other damage), (4) damage to or loosening of hinges and
latches, (5) evidence of dropping or abuse.
(c) Before turning on microwave power for any service test or inspection within the microwave generating
compartments, check the magnetron, wave guide or transmission line, and cavity for proper alignment,
integrity, and connections.
(d) Any defective or misadjusted components in the interlock, monitor, door seal, and microwave
generation and transmission systems shall be repaired, replaced, or adjusted by procedures described
in this manual before the oven is released to the owner.
(e) A microwave leakage check to verify compliance with the Federal Performance Standard should be
performed on each oven prior to release to the owner.
BEFORE SERVICING
Before servicing an operative unit, perform a microwave emission check as per the Microwave
Measurement Procedure outlined in this service manual.
If microwave emissions level is in excess of the specified limit, contact SHARP ELECTRONICS
CORPORATION immediately @1-800-237-4277.
If the unit operates with the door open, service person should 1) tell the user not to operate the oven
and 2) contact SHARP ELECTRONICS CORPORATION and The Food and Drug Administration's
Center for Devices and Radiological Health immediately.
Service personnel should inform SHARP ELECTRONICS CORPORATION of any certified unit
found with emissions in excess of 4mW/cm2. The owner of the unit should be instructed not to use
the unit until the oven has been brought into compliance.
16
R-209EK
WARNING TO SERVICE PERSONNEL
Microwave ovens contain circuitry capable of producing very high voltage and current, contact with
following parts may result in a severe, possibly
fatal, electrical shock.
(Example)
High Voltage Capacitor, High Voltage Power Transformer, Magnetron, High Voltage Rectifier Assembly, High Voltage Harness etc..
Read the Service Manual carefully and follow all
instructions.
Don't Touch !
Danger High Voltage
When the testing is completed,
1. Disconnect the power supply cord, and then remove
outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Reconnect the leads to the primary of the power
transformer.
5. Reinstall the outer case (cabinet).
6. Reconnect the power supply cord after the outer case is
installed.
7. Run the oven and check all functions.
Before Servicing
1. Disconnect the power supply cord
outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
, and then remove
WARNING:RISK OF ELECTRIC SHOCK.
DISCHARGE THE HIGH-VOLTAGE
CAPACITOR BEFORE SERVICING.
After repairing
The high-voltage capacitor remains charged about 60
seconds after the oven has been switched off. Wait for 60
seconds and then short-circuit the connection of the highvoltage capacitor (that is the connecting lead of the highvoltage rectifier) against the chassis with the use of an
insulated screwdriver.
1. Reconnect all leads removed from components during
testing.
2. Reinstall the outer case (cabinet).
3. Reconnect the power supply cord after the outer case is
installed.
4. Run the oven and check all functions.
Whenever troubleshooting is performed the power supply
must be disconnected. It may, in some cases, be necessary
to connect the power supply after the outer case has been
removed, in this event,
1. Disconnect the power supply cord, and then remove
outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the leads to the primary of the power
transformer.
5. Ensure that the leads remain isolated from other
components and oven chassis by using insulation tape.
6. After that procedure, reconnect the power supply cord.
Microwave ovens should not be run empty. To test for the
presence of microwave energy within a cavity, place a cup
of cold water on the oven turntable, close the door and set
the power to HIGH and set the microwave timer for two (2)
minutes. When the two minutes has elapsed (timer at zero)
carefully check that the water is now hot. If the water
remains cold carry out Before Servicing procedure and reexamine the connections to the component being tested.
When all service work is completed and the oven is fully
assembled, the microwave power output should be checked
and a microwave leakage test should be carried out.
1
R-209EK
MICROWAVE MEASUREMENT PROCEDURE
A. Requirements:
1) Microwave leakage limit (Power density limit): The power density of microwave radiation emitted by a microwave oven
should not exceed 1mW/cm2 at any point 5cm or more from the external surface of the oven, measured prior to acquisition
by a purchaser, and thereafter (through the useful life of the oven), 5 mW/cm2 at any point 5cm or more from the external
surface of the oven.
2) Safety interlock switches Primary interlock relay and door sensing switch shall prevent microwave radiation emission in
excess of the requirement as above mentioned, secondary interlock switch shall prevent microwave radiation emission
in excess of 5 mW/cm2 at any point 5cm or more from the external surface of the oven.
B. Preparation for testing:
Before beginning the actual measurement of leakage, proceed as follows:
1) Make sure that the actual instrument is operating normally as specified in its instruction booklet.
Important:
Survey instruments that comply with the requirement for instrumentation as prescribed by the performance standard
for microwave ovens, 21 CFR 1030.10(c)(3)(i), must be used for testing.
2) Place the oven tray in the oven cavity.
3) Place the load of 275±15 ml (9.8 oz) of tap water initially at 20±5˚C (68˚F) in the center of the oven cavity.
The water container shall be a low form of 600 ml (20 oz) beaker with an inside diameter of approx. 8.5 cm (3-1/2 in.) and
made of an electrically nonconductive material such as glass or plastic.
The placing of this standard load in the oven is important not only to protect the oven, but also to insure that any leakage
is measured accurately.
4) Set the cooking control on Full Power Cooking Mode
5) Close the door and select a cook cycle of several minutes. If the water begins to boil before the survey is completed,
replace it with 275 ml of cool water.
C. Leakage test:
Closed-door leakage test (microwave measurement)
1) Grasp the probe of the survey instrument and hold it perpendicular to the gap between the door and the body of the oven.
2) Move the probe slowly, not faster than 1 in./sec. (2.5 cm/sec.) along the gap, watching for the maximum indication on the
meter.
3) Check for leakage at the door screen, sheet metal seams and other accessible positions where the continuity of the metal
has been breached (eg., around the switches, indicator, and vents).
While testing for leakage around the door pull the door away from the front of the oven as far as is permitted by the closed
latch assembly.
4) Measure carefully at the point of highest leakage and make sure that the highest leakage is no greater than 4mW/cm2.
NOTE: After servicing, record data on service invoice and microwave leakage report.
2
R-209EK
SERVICE MANUAL
MICROWAVE OVEN
R-209EK
FOREWORD
This Manual has been prepared to provide Sharp Electronics Corp. Service Personnel with Operation and Service
Information for the SHARP MICROWAVE OVEN, R-209EK.
The model R-209EK is quite similar to base model R-220EW (Refer No. is S0101R220EPW/).
It is recommended that service personnel carefully study the entire text of this manual and the base model's manual so that
they will be qualified to render satisfactory customer service.
Check the interlock switches and the door seal carefully. Special attention should be given to avoid electrical shock and
microwave radiation hazard.
WARNING
Never operate the oven until the following points are ensured.
(A) The door is tightly closed.
(B) The door brackets and hinges are not defective.
(C) The door packing is not damaged.
(D) The door is not deformed or warped.
(E) There is no other visible damage with the oven.
Servicing and repair work must be carried out only by trained service personnel.
DANGER
Certain initial parts are intentionally not grounded and present a risk of electrical shock only during servicing.
Service personnel - Do not contact the following parts while the appliance is energized;
High Voltage Capacitor, Power Transformer, Magnetron, High Voltage Rectifier Assembly, High Voltage
Harness;
If provided, Vent Hood, Fan assembly, Cooling Fan Motor.
All the parts marked “*” on parts list are used at voltages more than 250V.
Removal of the outer wrap gives access to voltage above 250V.
All the parts marked “∆” on parts list may cause undue microwave exposure, by themselves, or when they are damaged,
loosened or removed.
SHARP ELECTRONICS CORPORATION
SHARP PLAZA, MAHWAH,
NEW JERSEY 07430-2135
3
R-209EK
PRODUCT DESCRIPTION
SPECIFICATIONS
ITEM
DESCRIPTION
Power Requirements
120 Volts
60 Hertz
Single phase, 3 wire grounded
Power Consumption
1200W / Approx. 10.2 Amperes
Power Output
800 W nominal of RF microwave energy (IEC Test procedure)
Operating frequency 2450 MHz
Case Dimensions
Width 18-1/8"
Height 11-3/8"
Depth 14-5/8"
Cooking Cavity Dimensions
(0.8 Cubic feet)
Width 12-3/8"
Height 8-3/8"
Depth 13"
Control Complement
Touch Control System
Clock (1:00 - 12:59)
Timer (0 - 99 minutes 99 seconds)
Microwave Power for Variable Cooking
Repetition Rate;
P-HI ................................... Full power throughout the cooking time
P-90 .................................................... approx. 90% of FULL Power
P-80 .................................................... approx. 80% of FULL Power
P-70 .................................................... approx. 70% of FULL Power
P-60 .................................................... approx. 60% of FULL Power
P-50 .................................................... approx. 50% of FULL Power
P-40 .................................................... approx. 40% of FULL Power
P-30 .................................................... approx. 30% of FULL Power
P-20 .................................................... approx. 20% of FULL Power
P-10 .................................................... approx. 10% of FULL Power
P-0 ...................................... No power throughout the cooking time
POPCORN pad, MINUTE PLUS pad
REHEAT CENTER pad, Instant Start pads
EXPRESS DEFROST pad
Number selection pads, CLOCK pad
KITCHEN TIMER pad, POWER LEVEL pad
STOP/CLEAR pad, START pad
Oven Cavity Light
Yes
Safety Standard
UL Listed.
FCC Authorized
DHHS RUles, CFR, Title 21, Chapter 1, Subchapter J
4
R-209EK
TOUCH CONTROL PANEL
EXPRESS
DEFROST
POPCORN
MINUTE
PLUS
See note
TO ADJUST QUANTITY TOUCH SAME PAD AGAIN
BAKED
POTATOES
FRESH
VEGETABLES
FROZEN
ENTREES
DINNER
PLATE
BEVERAGE
ROLLS
MUFFINS
NOTE:
The directed features are disabled after three
minutes when the oven is not in use. These
features are automatically enabled when the
door is opened and closed or the STOP/ CLEAR
pad is pressed.
Timer
Clock
Power
Level
Stop
Clear
START
SCHEMATIC
NOTE: CONDITION OF OVEN
1. DOOR CLOSED
2. CLOCK APPEARS ON DISPLAY
C/T FUSE
See note
NOTE: " " indicates components with potential above 250V.
MAGNETRON
THERMAL CUT-OUT
COM.
POWER
TRANSFORMER
N.O.
(RY-2)
(RY-1)
A3
PRIMARY
INTERLOCK
RELAY
CAPACITOR
0.86µF
CONTROL UNIT
A1
B1
B2
DOOR
SENSING
SWITCH
TTM
OL
TURNTABLE
MOTOR
OVEN
LAMP
MAGNETRON
GRN
120V AC
60 Hz
MONITOR
SWITCH
FM
RECTIFIER
FAN
MOTOR
SECONDARY
INTERLOCK
SWITCH
Figure O-1. Oven Schematic-Off Condition
5
R-209EK
TEST PROCEDURES (CONT'D)
PROCEDURE
LETTER
J
COMPONENT TEST
KEY UNIT TEST
1. Disconnect the power supply cord and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. If the display fails to clear when the STOP/CLEAR pad is depressed, first verify the flat ribbon cable is
making good contact, verify that the door sensing switch (stop switch) operates properly; that is the
contacts are closed when the door is closed and open when the door is open. If the door sensing switch
(stop switch) is good, disconnect the flat ribbon cable that connects the key unit to the control unit and
make sure the door sensing switch is closed (either close the door or short the door sensing switch
connector). Use the Key unit matrix indicated on the control panel schematic and place a jumper wire
between the pins that correspond to the STOP/CLEAR pad making momentary contact. If the control
unit responds by clearing with a beep the key unit is faulty and must be replaced. If the control unit does
not respond, it is faulty and must be replaced. If a specific pad does not respond, the above method
may be used (after clearing the control unit) to determine if the control unit or key pad is at fault.
5. Reconnect all leads removed from components during testing.
6. Re-install the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.
L
G6
G5
G4
G3
G2
G1
G7
BEVERAGE
6
2
DINNER
PLATE
MINUTE
PLUS
G8
FRESH
VEGETABLES
3
5
4
EXPRESS
DEFROST
Power
Level
G9
ROLLS
MUFFINS
Timer
Clock
0
1
BAKED
POTATOES
Stop
Clear
G10
FROZEN
ENTREES
9
8
7
POPCORN
START
EXPRESS DEFROST TEST
(1) Place one cup of water in the center of the turntable tray in the oven cavity.
(2) Close the door, touch the " EXPRESS DEFROST " pad once for 0.5lbs in weight.
(3) The oven is in Express Defrost cooking condition.
(4) The oven will operate as follows.
MENU
1ST STAGE
2ND STAGE
3RD STAGE
4TH STAGE
EXPRESS DEFROST
LEVEL
TIME
LEVEL
TIME
LEVEL
TIME
LEVEL
TIME
0.5lb
70%
57sec.
0%
57sec.
50%
32sec.
30%
45sec.
(5) If improper operation is indicated, the control unit is probably defective and should be checked.
6
H
1
2
1
3
3
7
ORG
ORG
RED
CN-A
1 ORG
2
3 WHT
4
GRY
WHT
WHT
WHT
TURNTABLE
MOTOR
GRY
ORG
ORG
5
WHT
GRY
ORG
ORG
N
H.V.
RECTIFIER
POWER
TRANSFORMER
HIGH VOLTAGE
WIRE B
MAGNETRON
HIGH
VOLTAGE
CAPACITOR
HIGH VOLTAGE COMPONENTS
BLK
4
5
Figure S-1. Pictorial Diagram
SECONDARY
INTERLOCK SWITCH
COM
N.O.
COM
GRY
GRY
ORG
RED
MAGNETRON
THERMAL CUT-OUT
NOTE:
The neutral (WHT) wire must be
connected to the terminal with "N"
mark on the power supply cord.
POWER SUPPLY CORD
120V 60Hz
3
MONITOR
SWITCH
N.C.
RED
FAN MOTOR
WHT
GRY
C
CN-A
CN-B
1 GRY
2 GRN
GRY
GRN
OVEN LAMP
RED
WHT
2
RY2
RY1
COM
N.O.
WHT
RED
D
1
CN-B
SP1
F
DOOR
SENSING SWITCH
GRD
A
GRN
GRN
RED
1
2
CONTROL UNIT
G
To chassis support
BLK
NOTE:
The grounding conductor of
the power supply cord has
been grounded by power
supply cord fixing screw.
The screw must always be
kept tight.
B
H
E
C/T FUSE
R-209EK
6
A
B
C
6
D
E
F
G
H
3
8
4
DOOR
SENSING
SWITCH
B1
B2
COM
NO
RY2
RY1
C1 0.1µ/50v
C2 470µ/25v
3.3k 1/4w
R30
SP1
PKM22EPT
Q20
DTA143EKA
R41 15k
C20
0.1µ
/25v
5
(J12) 20k
(J10) 7.5k
(J14)
R73 15k
R72 15k
R71 15k
R70 15k
(J13) 4.7k
(J15) 4.7k C7
0.1µ
(J11) 10k /25v
54
14
P43
P42
P41
P40
15
AVSS
AVREF
AVDD
VDD
VD1
OCS4
OCS3
RESET
TEST
VSS
1
R02
G10
G9
G8
G7
2
5
0
8
6
3
Timer
Clock
9
30
G4
KEY UNIT
FRESH
VEGETABLES
ROLLS
MUFFINS
FROZEN
ENTREES
BEVERAGE
G6
29
COM2
COM3
SEG0
SEG1
SEG2
SEG3
SEG4
SEG5
SEG6
SEG7
SEG8
SEG9
SEG10
S11
S12
S9
S8
G3
G2
7
Power
Level
Stop
Clear
G1
POPCORN START
DINNER MINUTE
PLATE
PLUS
EXPRESS
4
DEFROST
BAKED
1
POTATOES
R65
15k
G5
IC1
IXA078DR
44
SEG11
SEG12
45
5
Figure S-2. Control Panel Circuit
: IF NOT SPECIFIED, 1/10W ± 5%
: IF NOT SPECIFIED, 1SS270A
7
6
5
Q30 DTA143EKA
Q10 DTA143EKA
VC
C6
0.1µ/25v
C5 0.1µ/25v
ON DEF. LBS QTY. CHECK
4
NOTE
D40
D22
–
+
C8 47µ/16v
C21 10µ/35v
Q22
DTA143ES
Q21
DTD143ES
4
3
2
Q1
2SA1037AK
GND
3
GND
AC(H)
MICRO
A1
c
VR
R4
910 1/2w
–
R10 15k
R20 15k
VRS1 10G471K
b
D20
D21
ZD1
R78 220k
C10
0.1µ
/25v
R40 4.7k
OVEN LAMP
TURNTABLE
MOTOR
FAN MOTOR
a
d
C40 0.01µ/25v
HZ4C3
R77 220k
C3 0.01µ/25v
C11 0.01µ/25v
R5
1k
R76 220k
0.01µ
/25v
C61 330p/50v
+
VC3
BZ
–
VC2
R00
+
VC1
R01
D4
P20
D2
R03
1
P21
GND
S10
D3
S5
D1
SEG16
A3
P22
R50 20kF
R75 220k
SEG19
P23
AC120V
60Hz
S4
AC(N)
SEG15
C4
C63 330p/50v
SEG18
K00
R6 15k
C62 330p/50v
SEG17
K01
G
C60 330p/50v
2
R67
15k
2
SEG14
H
K02
D
SEG13
LIQUID CRYSTAL DISPLAY
S7
S6
R64
15k
CPU UNIT
S3
S2
POWER UNIT
S1
D1-D4
11ES1
C1
1
R63
15k
F
C2
C3
E
R62
15k
C
K03
B
COM0
A
COM1
1
R66
15k
T1
R-209EK
6
A
B
C
6
D
E
F
G
H
(J1)
R-209EK
PARTS LIST
Note: The parts marked “∆” may cause undue microwave exposure.
The parts marked “*” are used in voltage more than 250V.
REF. NO.
PART NO.
DESCRIPTION
Q'TY
CODE
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
AH
AS
AN
AP
BH
AQ
AQ
AQ
AW
AT
AU
AV
BL
BE
AL
AS
AW
AK
1
1
2
AY
AF
AC
1
1
1
1
1
3
3
BH
BD
AV
AM
AE
AA
AA
1
1
2
1
1
1
1
1
1
1
1
1
1
2
1
1
1
AL
AP
AD
AF
AL
AG
-AD
AE
AG
AM
AH
AH
AE
AN
AG
AC
1
1
1
1
1
1
1
4
1
AT
AR
AT
AE
AB
AG
AK
AA
AC
1
1
1
AP
AN
AM
ELECTRIC PARTS
*
*
*
*
*
*
*∆
*∆
1- 1
1- 2
1- 3
1- 3
1- 4
1- 5
1- 5
1- 5
1- 6
1- 6
1- 7
1- 7
1- 8
1- 8
1- 9
1-10
1-10
1-11
QSW-MA137WRE0
FFS-BA025WRKZ
FACCDA086WREZ
FACCDA081WRE0
RTRN-A604WRZZ
FH-DZA087WRK0
FH-DZA081WRK0
FH-DZA082WRK0
RC-QZA201WRE0
RC-QZA228WRE0
RMOTEA355WRE0
RMOTEA383WRE0
RV-MZA306WRZZ
RV-MZA226WRE0
RLMPTA082WRZZ
RMOTDA211WRE0
RMOTDA186WRE0
RTHM-A116WRE0
Secondary interlock switch & door sensing switch
C/T fuse & monitor switch(AM51620C53Y1) assembly
Power supply cord
Power supply cord (Interchangeable)
Power transformer
High voltage rectifier
High voltage rectifier (Interchangeable)
High voltage rectifier (Interchangeable)
High voltage capacitor
High voltage capacitor (Interchangeable)
Fan motor
Fan motor (Interchangeable)
Magnetron
Magnetron (Interchangeable)
Oven lamp
Turntable motor
Turntable motor (Interchangeable)
Thermal cut-out 125˚C
2- 1
2- 2
2- 3
GCABUA756WRPZ
GDAI-A304WRW0
GLEGPA074WRE0
Outer case cabinet
Bottom plate
Foot
3333333-
DPWBFC132WRUZ
FPNLCB543WRKZ
FUNTKB036WREZ
RLCDSA089DRZZ
QCNC-A013WRZZ
XEPSD30P08XS0
XEPSD30P08XS0
Control unit
Control panel frame with key unit and LCD
Key unit
Liquid crystal display
Rubber connector
Screw; 3mm x 8mm
Screw; 3mm x 8mm
PHOK-A105WRF0
LANGQA530WRWZ
PCUSUA502WRP0
LBNDKA038WRP0
NFANJA029WRE0
PDUC-A694WRF0
*************
GLEGPA073WRF0
LANGTA318WRP0
PCUSGA389WRP0
PCOVPA276WRE0
PCOVPA342WRF0
PCOVPA343WRF0
PCUSUA443WRP0
PDUC-A700WRF0
PPACGA097WRE0
PCUSUA474WRP0
Latch hook
Light mount plate
Waterproof cushion
Capacitor holder
Fan blade
Fan duct
Oven cavity (Not replaceable part)
Leg
Chassis support
Cushion
Waveguide cover
B-cover Right
B-cover Left
Cushion
Air separator
O-ring
Cushion
CABINET PARTS
CONTROL PANEL PARTS
1
2
2-1
2-2
3
4
4
OVEN PARTS
∆
∆
4- 1
4- 2
4- 3
4- 4
4- 5
4- 6
4- 7
4- 8
4- 9
4-10
4-11
4-12
4-13
4-14
4-15
4-16
4-17
DOOR PARTS
∆
∆
555555555-
1
2
3
4
5
6
7
8
9
FDORFA321WRT0
GWAKPA772WRFZ
HPNL-A746WRRZ
LSTPPA175WRF0
MSPRTA084WRE0
PSHEPA622WRE0
GCOVHA390WRF0
XEPSD40P08000
PCUSUA575WRPZ
Door panel
Door frame
Door screen
Latch head
Latch spring
Sealer film
Choke cover
Screw : 4mm x 8mm
Cushion
6- 1
6- 2
6- 3
FROLPA089WRK0
NTNT-A094WRE0
TINSEA874WRRZ
Turntable support
Turntable
Instruction book
MISCLANEOUS
9
R-209EK
REF. NO.
6- 4
6- 5
* 6- 6
6- 7
6- 8
6- 9
PART NO.
FW-VZB657WRE0
FW-VZB831WREZ
QW-QZA242WRZZ
TCAUAA265WRRZ
TCAUAA257WRRZ
TCAUAA253WRR0
DESCRIPTION
Switch harness
Main wire harness
High voltage wire B
DHHS caution label
Monitor caution
Earth caution
Q'TY
1
1
1
1
1
2
CODE
AH
AQ
AF
AC
AC
AC
2
2
1
1
5
1
2
12
4
2
3
1
AA
AB
AB
AA
AA
AA
AA
AA
AA
AC
AA
AA
SCREWS AND WASHERS
7- 1
7- 2
7- 3
7- 4
7- 5
7- 6
7- 7
7- 8
7- 9
7-10
7-11
7-12
XHPSD40P08K00
LX-EZA042WRE0
LX-WZA028WRE0
XHTSD40P12RV0
XHTSD40P08RV0
XHPSD30P06000
LX-CZ0052WRE0
XOTSD40P12000
XOTSF40P08000
LX-CZA070WRE0
XHPSD40P08000
XOTSD40P08000
Screw :
Special
Special
Screw :
Screw :
Screw :
Special
Screw :
Screw :
Special
Screw :
Screw :
4mm x 8mm
screw
washer
4mm x 12mm
4mm x 8mm
3mm x 6mm
screw
4mm x 12mm
4mm x 8mm
screw
4mm x 8mm
4mm x 8mm
HOW TO ORDER REPLACEMENT PARTS
To have your order filled promptly and correctly, please furnish the following information.
1. MODEL NUMBER
2. REF. NO.
3. PART NO.
4. DESCRIPTION
Order Parts from the authorized SHARP parts Distributor for your area.
Defective parts requiring return should be returned as indicated in the Service Policy.
10
R-209EK
2
1
4
3
6
5
OVEN AND CABINET PARTS
7-8
7-10
A
A
7-8
2-1
7-9
7-12
7-10
1-9
B
B
4-3
7-8
7-11
4-2
1-8
4-17
C
7-9
6-8
C
6-7
6-9
7-4
4-5
4-14
6-9
1-2
1-3
4-14
D
7-5
4-6
7-5
D
1-6
E
4-7
7-5
A
4-11
A
1-7
E
1-5
6-2
7-3
1-11
7-1
7-6
4-9
4-4
4-16
7-7
1-10
F
6-1
1-1
4-10
7-2
1-2
7-1
F
4-1
7-8
1-1
4-15
4-3
4-8
1-4
G
G
2-2
7-8
2-3
4-13
7-8
7-8
7-8
2-3
H
7-8
H
4-12
7-8
1
2
4
3
11
5
6
R-209EK
2
1
3-1
3-2-2
A
3-4
3-2
B
6
5
CONTROL PANEL PARTS
Befor attaching Control unit to
Control panel, foil side of Control
unit must be cleaned by ethylalcohol.
A
4
3
3-4
3-3
B
C
C
DOOR PARTS
3-2-1
5-6
5-8
5-7
D
D
5-1
5-8
5-2
E
E
5-3
5-9
5-4
5-5
F
F
MISCELLANEOUS
6-4
6-5
G
G
6-6
Actual wire harness may be different than illustration.
H
H
1
2
4
3
12
5
6
R-209EK
PACKING AND ACCESSORIES
TOP PAD ASSEMBLY
FPADBA387WRK0
DOOR PROTECTION SHEET
POLYETHYLENG BAG
SPADPA580WRE0
SSAKHA014WRE0
6-3 OPERATION MANUAL
6-2 TURNTABLE TRAY
MICROWAVE OVEN
BOTTOM PAD ASSEMBLY
FPADBA388WRK0
6-1
TURNRABLE SUPPORT
INTO THE
OVEN CAVITY
Not replaceable items.
TRAY PAD ASSY
(CPADBA244WRK0)
13
PACKING CASE
FPAK-A383WRKZ
R-209EK
COPYRIGHT © 2001 BY SHARP CORPORATION
ALL RIGHTS RESERVED.
No part of this publication may be reproduced,
stored in retrieval systems, or transmitted in any
form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior
written permission of the publisher.
2001 SHARP CORP. (4S2.530E) Printed in U.S.A
14