Yamaha HTR-6030 Owner's manual

01EN_HTR-6030_U_cv-1.fm Page 1 Tuesday, December 19, 2006 11:00 AM
U
HTR-6030
AV Receiver
OWNER’S MANUAL
IMPORTANT SAFETY INSTRUCTIONS
Important safety instructions
10
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
•
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert you to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle
is intended to alert you to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
1
2
3
4
5
6
7
8
9
Read Instructions – All the safety and operating instructions
should be read before the product is operated.
Retain Instructions – The safety and operating instructions
should be retained for future reference.
Heed Warnings – All warnings on the product and in the
operating instructions should be adhered to.
Follow Instructions – All operating and use instructions
should be followed.
Cleaning – Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners.
Attachments – Do not use attachments not recommended by
the product manufacturer as they may cause hazards.
Water and Moisture – Do not use this product near water –
for example, near a bath tub, wash bowl, kitchen sink, or
laundry tub; in a wet basement; or near a swimming pool;
and the like.
Accessories – Do not place this product on an unstable cart,
stand, tripod, bracket, or table. The product may fall,
causing serious injury to a child or adult, and serious
damage to the product. Use only with a cart, stand, tripod,
bracket, or table recommended by the manufacturer, or sold
with the product. Any mounting of the product should
follow the manufacturer’s instructions, and should use a
mounting accessory recommended by the manufacturer.
A product and cart combination should be moved with care.
Quick stops, excessive force, and uneven surfaces may
cause the product and cart combination to
overturn.
Caution-i En
11
12
13
14
15
16
17
18
19
Ventilation – Slots and openings in the cabinet are provided
for ventilation and to ensure reliable operation of the
product and to protect it from overheating, and these
openings must not be blocked or covered. The openings
should never be blocked by placing the product on a bed,
sofa, rug, or other similar surface. This product should not
be placed in a built-in installation such as a bookcase or rack
unless proper ventilation is provided or the manufacturer’s
instructions have been adhered to.
Power Sources – This product should be operated only from
the type of power source indicated on the marking label. If
you are not sure of the type of power supply to your home,
consult your product dealer or local power company. For
products intended to operate from battery power, or other
sources, refer to the operating instructions.
Grounding or Polarization – This product may be equipped
with a polarized alternating current line plug (a plug having
one blade wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If you
are unable to insert the plug fully into the outlet, try
reversing the plug. If the plug should still fail to fit, contact
your electrician to replace your obsolete outlet. Do not
defeat the safety purpose of the polarized plug.
Power-Cord Protection – Power-supply cords should be
routed so that they are not likely to be walked on or pinched
by items placed upon or against them, paying particular
attention to cords at plugs, convenience receptacles, and the
point where they exit from the product.
Lightning – For added protection for this product during a
lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent
damage to the product due to lightning and power-line
surges.
Power Lines – An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into such
power lines or circuits. When installing an outside antenna
system, extreme care should be taken to keep from touching
such power lines or circuits as contact with them might be
fatal.
Overloading – Do not overload wall outlets, extension
cords, or integral convenience receptacles as this can result
in a risk of fire or electric shock.
Object and Liquid Entry – Never push objects of any kind
into this product through openings as they may touch
dangerous voltage points or short-out parts that could result
in a fire or electric shock. Never spill liquid of any kind on
the product.
Servicing – Do not attempt to service this product yourself
as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
Damage Requiring Service – Unplug this product from the
wall outlet and refer servicing to qualified service personnel
under the following conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the
product,
c) If the product has been exposed to rain or water,
Important safety instructions
d)
20
21
22
23
If the product does not operate normally by following
the operating instructions. Adjust only those controls
that are covered by the operating instructions as an
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the product to its normal
operation,
e) If the product has been dropped or damaged in any
way, and
f)
When the product exhibits a distinct change in performance - this indicates a need for service.
Replacement Parts – When replacement parts are required,
be sure the service technician has used replacement parts
specified by the manufacturer or have the same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or other
hazards.
Safety Check – Upon completion of any service or repairs to
this product, ask the service technician to perform safety
checks to determine that the product is in proper operating
condition.
Wall or Ceiling Mounting – The unit should be mounted
to a wall or ceiling only as recommended by the
manufacturer.
Heat – The product should be situated away from heat
sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
24
Outdoor Antenna Grounding – If an outside antenna or
cable system is connected to the product, be sure the antenna
or cable system is grounded so as to provide some
protection against voltage surges and built-up static charges.
Article 810 of the National Electrical Code, ANSI/NFPA 70,
provides information with regard to proper grounding of the
mast and supporting structure, grounding of the lead-in wire
to an antenna discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode.
EXAMPLE OF ANTENNA GROUNDING
MAST
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810–20)
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810–21)
GROUND CLAMPS
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s
attention to Article 820-40 of the NEC that provides
guidelines for proper grounding and, in particular, specifies
that the cable ground shall be connected to the grounding
system of the building, as close to the point of cable entry as
practical.
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250. PART H)
NEC – NATIONAL ELECTRICAL CODE
FCC INFORMATION (for US customers)
1 IMPORTANT NOTICE: DO NOT MODIFY THIS
UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC, to
use the product.
2 IMPORTANT: When connecting this product to
accessories and/or another product use only high quality
shielded cables. Cable/s supplied with this product MUST
be used. Follow all installation instructions. Failure to
follow instructions could void your FCC authorization to
use this product in the USA.
3 NOTE: This product has been tested and found to comply
with the requirements listed in FCC Regulations, Part 15
for Class “B” digital devices. Compliance with these
requirements provides a reasonable level of assurance that
your use of this product in a residential environment will
not result in harmful interference with other electronic
devices.
This equipment generates/uses radio frequencies and, if
not installed and used according to the instructions found
in the users manual, may cause interference harmful to the
operation of other electronic devices.
Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this
product is found to be the source of interference, which
can be determined by turning the unit “OFF” and “ON”,
please try to eliminate the problem by using one of the
following measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient
the antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave., Buena Park, CA
90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
Caution-ii En
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
Caution: Read this before operating your unit.
1 To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2 Install this sound system in a well ventilated, cool, dry, clean
place – away from direct sunlight, heat sources, vibration,
dust, moisture, and/or cold. Allow ventilation space of at least
30 cm on the top, 20 cm on the left and right, and 20 cm on
the back of this unit.
3 Locate this unit away from other electrical appliances, motors,
or transformers to avoid humming sounds.
4 Do not expose this unit to sudden temperature changes from
cold to hot, and do not locate this unit in a environment with
high humidity (i.e. a room with a humidifier) to prevent
condensation inside this unit, which may cause an electrical
shock, fire, damage to this unit, and/or personal injury.
5 Avoid installing this unit where foreign object may fall onto
this unit and/or this unit may be exposed to liquid dripping or
splashing. On the top of this unit, do not place:
– Other components, as they may cause damage and/or
discoloration on the surface of this unit.
– Burning objects (i.e. candles), as they may cause fire,
damage to this unit, and/or personal injury.
– Containers with liquid in them, as they may fall and liquid
may cause electrical shock to the user and/or damage to
this unit.
6 Do not cover this unit with a newspaper, tablecloth, curtain,
etc. in order not to obstruct heat radiation. If the temperature
inside this unit rises, it may cause fire, damage to this unit,
and/or personal injury.
7 Do not plug in this unit to a wall outlet until all connections
are complete.
8 Do not operate this unit upside-down. It may overheat,
possibly causing damage.
9 Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cable from the wall outlet,
grasp the plug; do not pull the cord.
11 Do not clean this unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used. Using this
unit with a higher voltage than specified is dangerous and may
cause fire, damage to this unit, and/or personal injury. Yamaha
will not be held responsible for any damage resulting from use
of this unit with a voltage other than specified.
13 To prevent damage by lightning, keep the power cord and
outdoor antennas disconnected from a wall outlet or the unit
during a lightning storm.
14 Do not attempt to modify or fix this unit. Contact qualified
Yamaha service personnel when any service is needed. The
cabinet should never be opened for any reasons.
Caution-iii En
15 When not planning to use this unit for long periods of time
(i.e. vacation), disconnect the AC power plug from the wall
outlet.
16 Install this unit near the AC outlet and where the AC power
plug can be reached easily.
17 Be sure to read the “Troubleshooting” section on common
operating errors before concluding that this unit is faulty.
18 Before moving this unit, press STANDBY/ON to set this unit
in the standby mode, and disconnect the AC power plug from
the wall outlet.
19 VOLTAGE SELECTOR (Asia and General models only)
The VOLTAGE SELECTOR on the rear panel of this unit
must be set for your local main voltage BEFORE plugging
into the AC wall outlet.
Voltages are 110–120/220–240 V AC, 50/60 Hz.
20 The batteries shall not be exposed to excessive heat such as
sunshine, fire or like.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN
OR MOISTURE.
This unit is not disconnected from the AC power
source as long as it is connected to the wall outlet, even
if this unit itself is turned off by STANDBY/ON. This
state is called the standby mode. In this state, this unit
is designed to consume a very small quantity of power.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to
wide slot and fully insert.
This Class B digital apparatus complies with Canadian
ICES-003.
POUR LES CONSOMMATEURS CANADIENS
Pour éviter les chocs électriques, introduire la lame la
plus large de la fiche dans la borne correspondante de
la prise et pousser jusqu’au fond.
Cet appareil numérique de la classe B est conforme à
la norme NMB-003 du Canada.
IMPORTANT
Please record the serial number of this unit in the space
below.
MODEL:
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future
reference.
Contents
Features ................................................................... 2
Getting started ........................................................ 3
Quick start guide .................................................... 4
PREPARATION
Connections ........................................................... 10
Using set menu ........................................................ 44
1 SOUND MENU.................................................... 45
2 INPUT MENU...................................................... 48
3 OPTION MENU................................................... 50
Remote control features........................................51
Using remote control on the SCENE feature........... 51
Controlling this unit, a TV, or other components.... 52
Setting remote control codes ................................... 54
Advanced setup......................................................55
ADDITIONAL INFORMATION
Troubleshooting.....................................................56
Glossary..................................................................61
Specifications .........................................................63
Index .......................................................................64
APPENDIX
BASIC
OPERATION
(at the end of this manual)
Front panel................................................................i
Remote control ....................................................... ii
List of remote control codes ................................. iii
Basic setup ............................................................. 21
BASIC OPERATION
ADVANCED
OPERATION
Rear panel ................................................................ 10
Placing speakers....................................................... 11
Connecting speakers ................................................ 12
Setting the speaker impedance
(U.S.A. and Canada models only) ....................... 13
Information on jacks and cable plugs ...................... 14
Connecting video components................................. 15
Connecting audio components................................. 17
Connecting the FM and AM antennas ..................... 18
Connecting the power cable..................................... 18
Turning on and off the power .................................. 18
Front panel display .................................................. 19
Set menu.................................................................43
PREPARATION
Preparation: Check the items ..................................... 4
Step 1: Set up your speakers...................................... 5
Step 2: Connect your DVD player
and other components............................................ 6
Step 3: Turn on the power and
press SCENE 1 button ........................................... 8
What do you want to do with this unit?..................... 9
ADVANCED OPERATION
INTRODUCTION
INTRODUCTION
Selecting the SCENE templates........................... 23
Playback ................................................................ 27
Basic operations....................................................... 27
Additional operations............................................... 28
Sound field programs ........................................... 31
Sound field program descriptions............................ 31
FM/AM tuning ...................................................... 34
XM Satellite Radio tuning ................................... 37
Connecting the XM Mini-Tuner Dock .................... 37
Activating XM Satellite Radio ................................ 38
Basic XM Satellite Radio operations....................... 38
Setting XM Satellite Radio preset channels ............ 40
Displaying the XM Satellite Radio information...... 41
Recording .............................................................. 42
• y indicates a tip for your operation.
• Some operations can be performed by using either the
buttons on the front panel or the ones on the remote
control. In case the button names differ between the front
panel and the remote control, the button name on the
remote control is given in parentheses.
• This manual is printed prior to production. Design and
specifications are subject to change in part as a result of
improvements, etc. In case of differences between the
manual and product, the product has priority.
• “1 STANDBY/ON” or “A MULTI CH IN” (example)
indicates the name of the parts on the front panel or the
remote control. Refer to the attached sheet or the top pages
of this manual for the information about each position of
the parts.
• The symbol “☞ ” with page number(s) indicates the
corresponding reference page(s).
APPENDIX
Automatic tuning ..................................................... 34
Manual tuning.......................................................... 34
Automatic preset tuning........................................... 35
Manual preset tuning ............................................... 35
Selecting preset stations........................................... 36
Exchanging preset stations ...................................... 36
About this manual
ADDITIONAL
INFORMATION
Selecting the desired SCENE template.................... 23
Creating your original SCENE templates................ 26
English
1 En
Features
Features
Built-in 5-channel power amplifier
Sophisticated FM/AM tuner
◆ Minimum RMS output power
◆ 40-station random and direct preset tuning
◆ Automatic preset tuning
[U.S.A. and Canada models]
(1 kHz, 0.9% THD, 8 Ω)
Front: 100 W + 100 W
Center: 100 W
Surround: 100 W + 100 W
[Other models]
(1 kHz, 0.9% THD, 6 Ω)
Front: 100 W + 100 W
Center: 100 W
Surround: 100 W + 100 W
SCENE select function
◆ Preset SCENE templates for various situations
◆ 4 original SCENE templates for customizing capability
Decoders and DSP circuits
◆ Proprietary Yamaha technology for the creation of multichannel surround sound
◆ Compressed Music Enhancer mode to improve the sound
quality of compression artifacts (such as the MP3 format) to
that of a high-quality stereo
◆ Dolby Digital decoder
◆ Dolby Pro Logic/Dolby Pro Logic II decoder
◆ DTS decoder
◆ Neural Surround decoder
(U.S.A. and Canada models only)
◆ Virtual CINEMA DSP
◆ SILENT CINEMA™
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, and the double-D symbol are trademarks
of Dolby Laboratories.
“SILENT CINEMA” is a trademark of YAMAHA
CORPORATION.
XM Satellite Radio
(U.S.A. and Canada models only)
◆ XM Satellite Radio tuning capability (using the “XM MiniTuner Dock” sold separately)
◆ Neural Surround decoder to play back the XM HD content of
XM Satellite Radio broadcasts in multi-channels, resulting in
a full surround sound experience
Other features
◆ 192-kHz/24-bit D/A converter
◆ 6 additional input jacks for discrete multi-channel input
◆ Component video input/output capability
(3 COMPONENT VIDEO INs and 1 MONITOR OUT)
◆ Optical and coaxial digital audio signal jacks
◆ Sleep timer
◆ Cinema and music night listening modes
◆ Remote control with preset remote control codes
“DTS” and “DTS Digital Surround” are registered trademarks of
DTS, Inc.
The XM name and related logos are registered trademarks of XM
Satellite Radio Inc.
Neural Surround™ name and related logos are trademarks owned
by Neural Audio Corporation.
We Want You Listening For A Lifetime
Yamaha and the Electronic Industries Association’s Consumer
Electronics Group want you to get the most out of your
equipment by playing it at a safe level. One that lets the sound
come through loud and clear without annoying blaring or
distortion – and, most importantly, without affecting your
sensitive hearing.
2 En
Since hearing damage from loud sounds is often
undetectable until it is too late, Yamaha and the
Electronic Industries Association’s Consumer
Electronics Group recommend you to avoid
prolonged exposure from excessive volume levels.
Getting started
Getting started
■ Installing batteries in the remote control
Check that you received all of the following parts.
Remote control
POWER
TV
POWER
STANDBY
POWER
MUTE
Batteries (2)
(AAA, R03, UM-4)
1
AM loop antenna
3
AV
MULTI CH IN
AUDIO SEL
SLEEP
CD
MD/CD-R
TUNER
DVD
DTV/CBL
DVR
TV CH
TV MUTE
TV VOL
V-AUX
XM
AMP
TV INPUT
1
2
INTRODUCTION
■ Checking the supplied accessories
SCENE
BAND LEVEL
TITLE
3
4
SRCH MODE
VOLUME
MENU
2
Indoor FM antenna
ENTER
RETURN
XM MEMORY
DISPLAY
REC
l
1
PROG h
2
ENHANCER STRAIGHT
3
4
SUR.DECODE NIGHT
5
6
7
9
0
10
8
ENT.
Note
1
Take off the battery compartment cover.
The form of the supplied accessories varies depending on the
models.
2
Insert the two supplied batteries
(AAA, R03, UM-4) according to the polarity
markings (+ and –) on the inside of the
battery compartment.
3
Snap the battery compartment cover back
into place.
■ VOLTAGE SELECTOR
(Asia and General models only)
Caution
The VOLTAGE SELECTOR on the rear panel of this
unit must be set for your local voltage BEFORE
plugging the power cable into the AC wall outlet.
Improper setting of the VOLTAGE SELECTOR may
cause damage to this unit and create a potential fire
hazard.
Select the switch position (upper or lower)
according to your local voltage using a straight
slot screwdriver.
Voltages are 110-120/220-240 V AC, 50/60 Hz.
VOLTAGE
SELECTOR
110V120V
220V240V
Notes
• Change all of the batteries if you notice the following condition:
– the operation range of the remote control decreases.
• Do not use an old battery and a new one together.
• Do not use different types of batteries (such as alkaline and
manganese batteries) together. Read the packaging carefully as
these different types of batteries may have the same shape and
color.
• If the batteries have leaked, dispose of them immediately. Avoid
touching the leaked material or letting it come into contact with
clothing, etc. Clean the battery compartment thoroughly before
installing new batteries.
• Do not throw away batteries with general house waste; dispose
of them correctly in accordance with your local regulations.
• If the remote control is without batteries for more than 2
minutes, or if exhausted batteries remain in the remote control,
the contents of the memory may be cleared. When the memory
is cleared, insert new batteries and set up the remote control
code.
English
3 En
Quick start guide
Quick start guide
The following steps describe the easiest way to enjoy
DVD movie playback in your home theater.
Video monitor
Front right
speaker
In these steps, you need the following supplied
accessories.
Subwoofer
Front left
speaker
Preparation: Check the items
Surround right
speaker
❏ Indoor FM antenna
❏ AM loop antenna
The following items are not included in the package of this
unit.
Center speaker
❏ Speakers
❏ Front speakers ...................................... 2
DVD player
❏ Center speaker ...................................... 1
Surround left
speaker
❏ Surround speakers ............................... 2
Select magnetically shielded speakers. The
minimum required speakers are two front speakers.
❏ Active subwoofer ...................................... 1
Step 1: Set up your speakers
Select an active subwoofer equipped with an RCA
input jack.
❏ Speaker cables .......................................... 5
☞ P. 5
❏ Subwoofer cable ........................................ 1
Select a monaural RCA cable.
❏ DVD player ................................................. 1
Step 2: Connect your DVD player
and other components
☞ P. 6
Select DVD player equipped with coaxial digital
audio output jack and composite video output
jack.
❏ Video monitor ............................................. 1
Select a TV monitor, video monitor or projector
equipped with a composite video input jack.
❏ Video cable ................................................ 1
Select an RCA composite video cable.
❏ Digital coaxial audio cable ....................... 1
Step 3: Turn on the power and
press SCENE 1 button
☞ P. 8
Enjoy DVD playback!
4 En
Quick start guide
Be sure to connect the left channel (L), right channel
(R), “+” (red) and “–” (black) properly.
Step 1: Set up your speakers
Front speakers
XM
ANTENNA
Loosen
SPEAKERS
SURROUND
R
L
CENTER
Insert
INTRODUCTION
Place your speakers in the room and connect them to this
unit.
Tighten
FRONT B
R
L
COMPONENT VIDEO
DVD
DTV/CBL
DVR
MONITOR
OUT
AM
PR
GND
VIDEO
DIGITAL INPUT
PB
DVD
DTV/CBL
IN
MONITOR
OUT
DVR OUT
FM
75
OPTICAL
CD
3
Y
MULTI CH INPUT
FRONT
DTV/
CBL
2
DVD
1
COAXIAL
SURROUND
AUDIO
DVD
CENTER
L
L
R
R
DTV/CBL
IN
DVR OUT
OUTPUT
CD
IN
MD/ OUT
(PLAY) CD-R (REC)
SUB
WOOFER
R FRONT A
SUBWOOFER
L
1
Place your speakers and subwoofer in the
room.
2
Connect speaker cables to each speaker.
Front left speaker
To the front right
speaker
Center and surround speakers
Release
Insert
Press down
Cables are colored or shaped differently, perhaps with
a stripe, groove or ridge. Connect the striped
(grooved, etc.) cable to the “+” (red) terminals of
your speaker. Connect the plain cable to the “–”
(black) terminals.
3
Connect each speaker cable to the
corresponding speaker terminal of this unit.
1
2
3
To the surround
right speaker
4
To the center
speaker
To the surround
left speaker
1 Make sure that this unit and the subwoofer are
unplugged from the AC wall outlets.
2 Twist the exposed wires of the speaker cables
together to prevent short circuits.
3 Do not let the bare speaker wires touch each other.
4 Do not let the bare speaker wires touch any metal
part of this unit.
4
Connect the subwoofer cable to the input
jack of the subwoofer and the SUBWOOFER
OUTPUT jack of this unit.
Subwoofer
AV receiver
OUTPUT
IN
(PLAY)
MD/ OUT
CD-R (REC)
SUB
WOOFER
SUBWOOFER
OUTPUT jack
Subwoofer cable
5 En
English
Input jack
Quick start guide
Step 2: Connect your DVD player
and other components
XM
2
Connect the video cable to the composite
video output jack of your DVD player and the
DVD VIDEO jack of this unit.
AV receiver
SPEAKERS
ANTENNA
SURROUND
R
CENTER
L
FRONT B
R
L
COMPONENT VIDEO
DVD
DTV/CBL
MONITOR
OUT
DVR
AM
PR
GND
VIDEO
DIGITAL INPUT
PB
DVD
DTV/CBL
IN
DVR OUT
MONITOR
OUT
DVD
DTV/CBL
IN
DVR OUT
FM
75
DVD player
OPTICAL
CD
3
DTV/
CBL
2
Y
MULTI CH INPUT
FRONT
SURROUND
AUDIO
CENTER
L
DVD
L
IN
MD/ OUT
(PLAY) CD-R (REC)
SUB
WOOFER
1
R
COAXIAL
OUTPUT
CD
R
R FRONT A
SUBWOOFER
L
Make sure that this unit and the DVD
player are unplugged from the AC wall
outlets.
DVD VIDEO jack
Composite video
output jack
3
1
Connect the digital coaxial audio cable to the
digital coaxial audio output jack of your DVD
player and the DVD DIGITAL INPUT COAXIAL
jack of this unit.
DVD player
Video cable
Connect the video cable to the video input
jack of your video monitor and the VIDEO
MONITOR OUT jack of this unit.
Video monitor
AV receiver
AV receiver
L/MONO
S-VIDEO
VIDEO
VIDEO-1 IN
AUDIO
R
Y
PB
PR
L/MONO
COLOR STREAM HD
IN
R
AUDIO
Video input
jack
Video cable
Digital coaxial
audio output
jack
Digital coaxial audio
cable
6 En
DVD DIGITAL INPUT
COAXIAL jack
VIDEO MONITOR OUT
jack
Quick start guide
4
■ For further connections
• Using the other kind of speaker
combinations
☞ P. 11
• Connecting a video monitor and
DVD player
☞ P. 15
• Connecting a cable TV/satellite tuner and
DVD recorder
INTRODUCTION
Connect the FM and AM antennas to this
unit.
See page 18 for the details.
☞ P. 15
• Connecting to the COMPONENT VIDEO
jacks
☞ P. 16
Indoor FM antenna
AM loop antenna
• Using the VIDEO AUX jacks on the front
panel
☞ P. 16
• Connecting a CD player and an MD
recorder
☞ P. 17
• Connecting a DVD player via analog
multi-channel audio connection
☞ P. 17
Press and hold
Insert
Release
• Connecting an outdoor FM/AM antenna
☞ P. 18
• Connecting the XM Mini-Tuner Dock
☞ P. 37
y
The wire of the AM loop antenna does not have any polarity and
you can connect either end of the wire to AM or GND terminal.
5
Connect the power plug of this unit and other
components into the AC wall outlet.
English
7 En
Quick start guide
Step 3: Turn on the power and
press SCENE 1 button
Check the type of the connected speakers.
If the speakers are 6 ohm speakers, set “SP IMP.” to
“6ΩMIN” before using this unit (see page 13).
1
Turn on the video monitor connected to this
unit.
2
Press 1 STANDBY/ON on the front panel.
4
Start playback of the desired DVD on your
player.
5
Rotate 8 VOLUME to adjust the volume.
Note
When you change the input source or sound field program, the
SCENE mode is deactivated and the indicator on the SCENE
button turns off.
■ Using the other SCENE buttons
In the following cases, try pressing the corresponding
SCENE button to enjoy playback of the desired sources.
Case A: “I want to listen to a music disc from the
connected DVD player as the back ground
music for this room...”
3
Press F SCENE 1.
“DVD Viewing” appears in the front panel display,
and this unit automatically optimize own status for
the DVD playback.
Press F SCENE 2 (or
E SCENE 2) to select “Disc
Listening”.
Case B: “I want to watch a TV program...”
EDIT
SEARCH MODE
PRESET/TUNING
FM / AM
A/B/C/D/E
CATEGORY
A/B/C/D/E
MEMORY
Press F SCENE 3 (or
E SCENE 3) to select “TV
Viewing”.
DISPLAY
TUNING AUTO/MAN'L
Note
To use the “TV Viewing” template, you must connect a
cable TV or satellite tuner to this unit in advance. See
page 15 for details.
y
The indicator on the selected SCENE button lights up while
this unit is in the SCENE mode.
8 En
Quick start guide
Case C: “I want to listen to a music program from
the FM radio station...”
Notes
• To use the “Radio Listening” template, you must tune into
the desired radio station in advance. See pages 34 to 36 for
tuning information.
• To achieve the best possible reception, orient the
connected AM loop antenna, or adjust the position of the
end of the indoor FM antenna.
■ Customizing the SCENE templates
• Using various SCENE templates
☞ P. 23
■ Using various input sources
• Basic controls of this unit
☞ P. 27
y
• Enjoying FM/AM radio programs
If you cannot find the desired situation, you can select and change
the assigned SCENE template for the SCENE buttons. See
page 23 for details.
• Enjoying XM Satellite Radio programs
☞ P. 34
☞ P. 37
■ After using this unit...
Press 1 STANDBY/ON on the front panel to set
this unit to the standby mode.
INTRODUCTION
Press F SCENE 4 (or
E SCENE 4) to select “Radio
Listening”.
What do you want to do with this
unit?
■ Using various sound features
• Using various sound field programs
☞ P. 31
■ Adjusting the parameters of this unit
• Optimizing the speaker parameters for your
listening room (BASIC SETUP)
☞ P. 21
• Manually adjusting various parameters of
this unit
☞ P. 43
• Setting the remote control
☞ P. 51
• Adjusts the advanced parameters
This unit is set to the standby mode. In the standby mode,
this unit consumes a small amount of power in order to
receive infrared signals from the remote control. To turn
on this unit from the standby mode, press 1 STANDBY/
ON (or L POWER) on the front panel. See page 18 for
details.
Note
☞ P. 55
■ Additional features
Automatically turning off this unit
☞ P. 30
In the standby mode, this unit consumes a small amount of power
in order to receive infrared signals from the remote control.
English
9 En
Connections
Connections
Rear panel
1
2
3
4
XM
5
ANTENNA
SPEAKERS
SURROUND
R
L
CENTER
FRONT B
R
L
COMPONENT VIDEO
DTV/CBL
DVD
DVR
MONITOR
OUT
AM
PR
GND
VIDEO
DIGITAL INPUT
PB
DVD
DTV/CBL
IN
DVR OUT
MONITOR
OUT
FM
75
OPTICAL
CD
3
DTV/
CBL
2
Y
MULTI CH INPUT
FRONT
SURROUND
AUDIO
DVD
DTV/CBL
IN
DVR OUT
OUTPUT
CD
IN
MD/ OUT
(PLAY) CD-R (REC)
SUB
WOOFER
L
1
R
COAXIAL
DVD
CENTER
L
R
R FRONT A
SUBWOOFER
6
7
8
9
L
0
(U.S.A. model)
1 XM jack (U.S.A. and Canada models only)
See page 37 for connection information.
8 AUDIO jacks
See pages 15 and 17 for connection information.
2 COMPONENT VIDEO jacks
See page 16 for connection information.
9 SUBWOOFER OUTPUT jack
See page 12 for connection information.
3 VIDEO jacks
See pages 15 for connection information.
0 VOLTAGE SELECTOR
(Asia and General models only)
See page 3 for details.
4 ANTENNA terminals
See page 18 for connection information.
5 SPEAKERS terminals
See page 12 for connection information.
6 DIGITAL INPUT jacks
See page 17 for connection information.
7 MULTI CH INPUT jacks
See page 17 for connection information.
10 En
Connections
Placing speakers
The speaker layout below shows the speaker setting we recommend. You can use it to enjoy CINEMA DSP and multichannel audio sources.
FL
C
FR
FR
SW
30˚
FL
SR
PREPARATION
C
SL
SR
SL
60˚
SL
80˚
SR
1.8 m (6 ft)
Front left and right speakers (FL and FR)
The front speakers are used for the main source sound plus effect sounds. Place these speakers at an equal distance from the
ideal listening position. The distance of each speaker from each side of the video monitor should be the same.
Center speaker (C)
The center speaker is for the center channel sounds (dialog, vocals, etc.). If for some reason it is not practical to use a
center speaker, you can do without it. Best results, however, are obtained with the full system.
Surround left and right speakers (SL and SR)
The surround speakers are used for effect and surround sounds.
Subwoofer (SW)
The use of a subwoofer with a built-in amplifier, such as the Yamaha Active Servo Processing Subwoofer System, is
effective not only for reinforcing bass frequencies from any or all channels, but also for high fidelity sound reproduction
of the LFE (low-frequency effect) channel included in Dolby Digital and DTS sources. The position of the subwoofer is
not so critical, because low bass sounds are not highly directional. But it is better to place the subwoofer near the front
speakers. Turn it slightly toward the center of the room to reduce wall reflections.
English
11 En
Connections
Connecting speakers
Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are faulty,
this unit cannot reproduce the input sources accurately.
Caution
•
•
•
•
Use speakers with the specified impedance shown on the rear panel of this unit.
If you are to use 6 ohm speakers, be sure to set “SP IMP.” to “6Ω MIN” before using this unit (see page 13).
Before connecting the speakers, make sure that this unit is turned off.
Do not let the bare speaker wires touch each other or let them touch any metal part of this unit. This could damage
this unit and/or speakers.
• Use magnetically shielded speakers. If this type of speakers still creates the interference with the monitor, place the
speakers away from the monitor.
Front speakers (B)
Right
Left
Surround speakers
Right
Left
Center
speaker
XM
ANTENNA
SPEAKERS
SURROUND
R
L
CENTER
FRONT B
R
L
COMPONENT VIDEO
DTV/CBL
DVD
DVR
MONITOR
OUT
AM
PR
GND
VIDEO
DIGITAL INPUT
PB
DVD
DTV/CBL
IN
DVR OUT
MONITOR
OUT
FM
75
OPTICAL
CD
3
DTV/
CBL
2
Y
MULTI CH INPUT
FRONT
SURROUND
AUDIO
DVD
COAXIAL
DVD
CENTER
L
DTV/CBL
IN
DVR OUT
OUTPUT
CD
L
IN
MD/ OUT
(PLAY) CD-R (REC)
SUB
WOOFER
1
R
R
R FRONT A
SUBWOOFER
L
(U.S.A. model)
Subwoofer
■ Before connecting to the SPEAKERS
terminal
A speaker cord is actually a pair of insulated cables
running side by side. Cables are colored or shaped
differently, perhaps with a stripe, groove or ridges.
Connect the striped (grooved, etc.) cable to the “+” (red)
terminals of this unit and your speaker. Connect the plain
cable to the “–” (black) terminals.
12 En
Right
Left
Front speakers (A)
Remove approximately 10 mm (3/8”) of insulation
from the end of each speaker cable and then
twist the bare wires of the cable together to
prevent short circuits.
10 mm (3/8”)
Connections
■ Connecting to the FRONT A terminals
2
1
Red: positive (+)
Black: negative (–)
Caution
If you are to use 6 ohm speakers, set “SP IMP.” to “6Ω
MIN” as follows BEFORE using this unit.
3
Loosen the knob.
2
Insert the bare end of the speaker wire into
the hole on the terminal.
1
Make sure this unit is turned off.
See page 18 for details about turning on or off this
unit.
2
Press and hold 0 TONE CONTROL and
then press 1 STANDBY/ON to turn on this
unit.
This unit turns on, an the advanced setup menu
appears in the front panel display.
3
Press A PROGRAM l / h repeatedly to
select “SP IMP.”.
The following display appears in the front panel
display.
Tighten the knob to secure the wire.
Connecting the banana plug
(except Europe, Korea and Asia models)
The banana plug is a single-pole electrical connector
widely used to terminate speaker cables. First, tighten the
knob and then insert the banana plug connector into the
end of the corresponding terminal.
PREPARATION
1
3
Setting the speaker impedance
(U.S.A. and Canada models only)
Banana plug
SP IMP.- 8 MIN
4
■ Connecting to the FRONT B, CENTER,
and SURROUND terminals
Press B STRAIGHT repeatedly to select “6Ω
MIN”.
The following display appears in the front panel
display.
SP IMP.- 6 MIN
Red: positive (+)
Black: negative (–)
5
1
Press down the tab.
Press 1 STANDBY/ON to confirm your
selection and set this unit to the standby
mode.
Note
The setting you made is reflected next time you turn on this unit.
2
Insert the bare end of the speaker wire into
the hole on the terminal.
3
Release the tab to secure the wire.
English
13 En
Connections
Information on jacks and cable plugs
Audio jacks and cable plugs
DIGITAL AUDIO
DIGITAL AUDIO
L
R
COAXIAL
OPTICAL
(White)
(Red)
(Orange)
L
R
C
AUDIO
Left and right
analog audio
cable plugs
Coaxial
digital audio
cable plug
Video jacks and cable plugs
COMPONENT VIDEO
Y
PB
PR
VIDEO
(Yellow)
(Green)
(Blue)
(Red)
O
V
Y
PB
PR
Optical
digital
audio cable
plug
Composite
video cable
plug
Component
video cable
plugs
■ Audio jacks
■ Video jacks
This unit has three types of audio jacks. Connection
depends on the availability of audio jacks on your other
components.
This unit has two types of video jacks. Connection
depends on the availability of input jacks on your video
monitor.
AUDIO jacks
For conventional analog audio signals transmitted via left
and right analog audio cables. Connect red plugs to the
right jacks and white plugs to the left jacks.
VIDEO jacks
For conventional composite video signals transmitted via
composite video cables.
DIGITAL AUDIO COAXIAL jacks
For digital audio signals transmitted via coaxial digital
audio cables.
COMPONENT VIDEO jacks
For component signals, separated into the luminance (Y)
and chrominance (PB, PR) video signals transmitted on
separate wires of component video cables.
DIGITAL AUDIO OPTICAL jacks
For digital audio signals transmitted via optical digital
audio cables.
Video signal flow for MONITOR OUT
Notes
COMPONENT
VIDEO
• You can use the digital jacks to input PCM, Dolby Digital and
DTS bitstreams. All digital input jacks are compatible with
digital signals with up to 96 kHz of sampling frequency.
• This unit handles digital and analog signals independently. Thus
audio signals input at the digital jacks are not output at the
analog AUDIO OUT (REC) jacks.
• Pull out the cap from the optical jack before you connect the
fiber optic cable. Do not discard the cap. When you are not
using the optical jack, be sure to put the cap back in place. This
cap protects the jack from dust.
14 En
Input
VIDEO
Output
(MONITOR OUT)
PR
PR
PB
PB
Y
Y
Connections
Connecting video components
Connect the video components as follows.
y
Make sure that this unit and other
components are unplugged from the
AC wall outlets.
You can also connect a video monitor, DVD player, digital TV,
and cable TV to this unit using the COMPONENT VIDEO
connection (see page 16).
■ Connecting a cable TV/satellite tuner
and a DVD recorder
PREPARATION
■ Connecting a video monitor and a DVD
player
XM
XM
COMPONENT VIDEO
COMPONENT VIDEO
DVD
DTV/CBL
DVR
DVD
MONITOR
OUT
DTV/CBL
DVR
MONITOR
OUT
PR
PR
VIDEO
DIGITAL INPUT
PB
DVD
DTV/CBL
IN
VIDEO
DIGITAL INPUT
PB
MONITOR
OUT
DVR OUT
DVD
DTV/CBL
IN
DVR OUT
MONITOR
OUT
DVD
DTV/CBL
IN
DVR OUT
OPTICAL
OPTICAL
MULTI CH INPUT
FRONT
SURROUND
DTV/
CBL
2
DTV/CBL
IN
DVR OUT
MULTI CH INPUT
CD
FRONT
DVD
R
R
CD
1
R
COAXIAL
R
SUBWOOFER
R
V
C
Audio out
Video in
Audio out
O
V
L
Audio out
L
Video out
V
Video out
AUDIO
CENTER
L
SUBWOOFER
Audio out
SURROUND
L
L
1
COAXIAL
Y
AUDIO
DVD
CENTER
L
DVD
3
R
V
L
R
L
R
V
Video in
2
CD
Audio in
DTV/
CBL
Y
Audio out
3
Video out
CD
DVD player
Video monitor
Cable TV or
Satellite tuner
DVD recorder
indicates recommended connections
indicates recommended connections
indicates alternative connections
indicates alternative connections
English
15 En
Connections
■ Connecting to the COMPONENT VIDEO
jacks
■ Connecting to the VIDEO AUX jacks on
the front panel
You can enjoy high-quality pictures by connecting your
video monitor and video source components to this unit
using COMPONENT VIDEO connection.
Use the VIDEO AUX jacks on the front panel to connect a
game console or a video camera to this unit.
Note
Be sure to connect your video source components in the same
way you connect your video monitor to this unit. For example, if
you connect your video monitor to this unit using a
COMPONENT VIDEO connection, connect your video source
components to this unit using the COMPONENT VIDEO
connection.
Video monitor
Caution
Be sure to turn down the volume of this unit and other
components before making connections.
Notes
• To reproduce the source signals input at these jacks, select
“V-AUX” as the input source.
• The audio signals input at the PORTABLE mini jack take
priority over the ones input at the AUDIO L/R jacks.
Video in
Video out
DVD player
VOLUME
STANDBY
/ON
EDIT
SEARCH MODE
PRESET/TUNING
CATEGORY
A/B/C/D/E
FM/AM
Y
l
PRESET/TUNING/CH
h
MEMORY
DISPLAY
TUNING AUTO/MAN'L
SCENE
1
PB
PR
Y
PB
PR
l
PHONES
SPEAKERS
A/B/OFF
PROGRAM
2
3
STRAIGHT
NIGHT
h
TONE CONTROL
4
l
INPUT
VIDEO AUX
h
AUDIO SELECT
VIDEO
L
AUDIO
R
PORTABLE
EFFECT
SILENT CINEMA
VIDEO AUX
VIDEO
L
V
L
AUDIO
R
PORTABLE
COMPONENT VIDEO
DVD
DTV/CBL
DVR
MONITOR
OUT
PR
PB
R
Y
MULTI CH INPUT
FRONT
SURROUND
CENTER
Video
output
L
Audio
output
R
SUBWOOFER
16 En
PR
Y
PB
PR
Video out
PB
Video out
Y
Cable TV or
satellite tuner
DVD recorder
Game console or
video camera
3.5 mm
stereo mini
plug
Connections
Connecting audio components
Connect the audio components as follows.
■ Connecting a CD player and a CD
recorder/MD recorder
Make sure that this unit and other
components are unplugged from the
AC wall outlets.
Note
When you connect your CD player via analog and digital
connection, priority is given to the signal input at the DIGITAL
INPUT jack.
PREPARATION
VIDEO
DIGITAL INPUT
PB
DVD
DTV/CBL
IN
DVR OUT
MONITOR
OUT
FM
75
OPTICAL
CD
3
DTV/
CBL
2
Y
MULTI CH INPUT
FRONT
SURROUND
AUDIO
DVD
DVD
CENTER
L
DTV/CBL
IN
DVR OUT
IN
MD/ OUT
(PLAY) CD-R (REC)
CD
L
1
R
R
COAXIAL
SUBWOOFER
O
L
R
Audio out
L
Audio out
Audio out
CD player
R
L
R
Audio in
CD recorder or
MD recorder
indicates recommended connections
indicates alternative connections
■ Connecting to the MULTI CH INPUT jacks
This unit is equipped with 6 additional input jacks (FRONT L/R, SURROUND L/R, CENTER and SUBWOOFER) for
discrete multi-channel input from a multi-format player, external decoder or sound processor. Connect the output jacks
on your multi-format player or external decoder to the MULTI CH INPUT jacks. Be sure to match the left and right
output jacks to the left and right input jacks for the front and surround channels.
MULTI CH INPUT
DTV/
CBL
FRONT
SURROUND
Notes
CENTER
2
L
• When you select the component connected to the MULTI CH
INPUT jacks as the input source (see page 28), this unit
automatically turns off the digital sound field processor, and
you cannot select sound field programs.
• This unit does not redirect signals input at the MULTI CH
INPUT jacks to accommodate for missing speakers. We
recommend that you connect a 5.1-channel speaker system
before using this feature.
1
R
R
L
R
Center out
Front out
L
Subwoofer out
SUBWOOFER
Surround out
DVD
COAXIAL
English
Multi-format player or
external decoder
17 En
Connections
Connecting the FM and AM
antennas
Connecting the power cable
Both FM and AM indoor antennas are supplied with this
unit. In general, these antennas should provide sufficient
signal strength. Connect each antenna correctly to the
designated terminals.
Once all connections are complete, plug the power cable
into the AC wall outlet.
Power cable
(U.S.A. model)
Notes
• The AM loop antenna should be placed away from this unit.
• A properly installed outdoor antenna provides clearer reception
than an indoor one. If you experience poor reception quality,
install an outdoor antenna. Consult the nearest authorized
Yamaha dealer or service center about outdoor antennas.
• The AM loop antenna should always be connected, even if an
outdoor AM antenna is connected to this unit.
Outdoor AM antenna
Use a 5 to 10 m (16 to 32 ft) of
vinyl-covered wire extended
outdoors from a window.
AM loop
antenna
(supplied)
Indoor FM
antenna
(supplied)
To the AC wall outlet
ANTENNA
Turning on and off the power
AM
■ Turning on this unit
GND
FM
75
UNBAL.
IN
MD/
(PLAY) CD-R
Press 1 STANDBY/ON (or L POWER) to turn
on this unit.
y
When you turn on this unit, there will be a 4 to 5-second delay
before this unit can reproduce sound.
■ Set this unit to the standby mode
Ground
For maximum safety and minimum
interference, connect the antenna GND
terminal to a good earth ground. A good
earth ground is a metal stake driven into
moist earth.
18 En
Press 1 STANDBY/ON (or M STANDBY) to set
this unit to the standby mode.
In the standby mode, this unit consumes a small amount of
power in order to receive infrared signals from the remote
control.
Connections
Front panel display
1
2
3
5
4
DVR
t
VIRTUAL
ENHANCER
V-AUX
SP SILENT CINEMA
NIGHT
AB
DTV/CBL
6
MD/CD-R
DVD
TUNER
7
CD
q PL
HiFi DSP
ft
q PL
0
A
B
1 Decoder indicator
Lights up when any of the decoders of this unit functions.
2 ENHANCER indicator
Lights up when the Compressed Music Enhancer mode is
selected (see page 31).
3 VIRTUAL indicator
Lights up when Virtual CINEMA DSP is active (see
page 33).
4 SILENT CINEMA indicator
Lights up when headphones are connected and a sound
field program is selected (see page 33).
5 Input source indicators
The corresponding cursor lights up to show the currently
selected input source.
6 Tuner indicators
Lights up when this unit is in the FM, AM or XM Satellite
Radio tuning mode (see pages 34 and 37).
C
D
E
VOLUME
dB
LFE
L C R
SL
SR
F
B NIGHT indicator
Lights up when you select a night listening mode (see
page 28).
C CINEMA DSP indicator
Lights up when you select a CINEMA DSP sound
field program (see page 31).
HiFi DSP indicator
Lights up when you select a HiFi DSP sound field
program (see page 31).
D Multi-information display
Shows the name of the current sound field program and
other information when adjusting or changing settings.
E SLEEP indicator
Lights up while the sleep timer is on (see page 30).
F Input channel and speaker indicators
LFE
LFE indicator
7 MUTE indicator
Flashes while the MUTE function is on (see page 28).
L C R
SL
SR
8 VOLUME level indicator
Indicates the current volume level.
LFE indicator
Lights up when the input signal contains the LFE
signal.
9 PCM indicator
Lights up when this unit is reproducing PCM (Pulse Code
Modulation) digital audio signals.
0 Headphones indicator
Lights up when headphones are connected (see page 28).
PREPARATION
mS
dB
neural
9
XM
AUTO TUNED STEREO MEMORY
PRESET
SLEEP MUTE
q DIGITAL
PCM
8
Input channel indicators
Input channel indicators
Indicate the channel components of the current digital
input signal.
A SP A B indicators
Light up according to the set of front speakers selected
(see page 27).
English
19 En
Connections
■ Using the remote control
The remote control transmits a directional infrared ray.
Be sure to aim the remote control directly at the remote
control sensor on this unit during operation.
VOLUME
STANDBY
/ON
EDIT
SEARCH MODE
PRESET/TUNING
FM/AM
CATEGORY
A/B/C/D/E
l
PRESET/TUNING/CH
h
MEMORY
DISPLAY
TUNING AUTO/MAN'L
SCENE
1
l
PHONES
SPEAKERS
A/B/OFF
TONE CONTROL
PROGRAM
2
3
STRAIGHT
NIGHT
h
4
l
INPUT
VIDEO AUX
h
AUDIO SELECT
VIDEO
L
AUDIO
R
PORTABLE
EFFECT
SILENT CINEMA
30º
30º
Approximately 6 m (20 ft)
X Infrared window
Outputs infrared control signals. Aim this window at the
component you want to operate.
y
To set the remote control codes for other components, see
page 54.
Notes
• Do not spill water or other liquids on the remote control.
• Do not drop the remote control.
• Do not leave or store the remote control in the following types
of conditions:
– places of high humidity, such as near a bath
– places of high temperature, such as near a heater or stove
– places of extremely low temperatures
– dusty places
20 En
Basic setup
Basic setup
The “BASIC SETUP” feature is a useful way to set up your system quickly and with minimal effort.
Notes
1
Press D AMP on the remote control.
2
Press P MENU.
“BASIC SETUP” appears in the front panel display.
5
SUBWOOFER .. YES
. BASIC SETUP
3
Choices: YES, NONE
• Select “YES” if you have a subwoofer in your
system.
• Select “NONE” if you do not have a subwoofer in
your system.
Press G ENTER to enter “BASIC SETUP”.
“ROOM” appears in the front panel display.
6
ROOM:
4
S >M
L
Press Gl / h to select the desired setting.
Select the size of the room where you have installed
your speakers. In general, the room sizes are defined
as follows:
Press Gn to select “SUBWOOFER” and then
Gl / h to select the desired setting.
PREPARATION
• Make sure you disconnect your headphones from this unit.
• If you wish to configure this unit manually using more precise adjustments, use the detailed parameters in “SOUND MENU”
(see page 45).
• Altering any parameters in “BASIC SETUP” resets all parameters manually adjusted in “SOUND MENU” (see page 45).
• Initial settings are indicated in bold under each parameter.
• Press HRETURN on the remote control to return to the previous menu level.
Press Gn to select “SPEAKERS” and then
Gl / h to select the number of speakers
connected to this unit.
SPEAKERS..5spk
Choice
Display
Speakers
Choices: S, M, L
[U.S.A. and Canada models]
S (small)
16 x 13 ft, 200 ft2 (4.8 x 4.0 m, 20 m2)
M (medium) 20 x 16 ft, 300 ft2 (6.3 x 5.0 m, 30 m2)
L (large)
26 x 19 ft, 450 ft2 (7.9 x 5.8 m, 45 m2)
[Other models]
S (small)
3.6 x 2.8 m, 10 m2
M (medium) 4.8 x 4.0 m, 20 m2
L (large)
6.3 x 5.0 m, 30 m2
2spk
L
R
3spk
L
C R
4spk
L
SL
R
SR
5spk
L C R
SL
SR
Front L/R
Front L/R, Center
Front L/R, Surround L/R
Front L/R, Center, Surround L/R
English
21 En
Basic setup
7
Press G n to select “SET” and then G l / h
to select the desired setting.
SET
10
Press G ENTER to confirm your selection.
• If you selected “YES” in step 9, the setup
procedure is completed and the display returns to
the top set menu display.
• If you selected “NO” in step 9, the front speaker
level adjustment display appears in the front panel
display.
11
Press Gk / n to select a speaker and then
Gl / h to adjust the balance.
The selected speaker and the front left speaker (or the
surround left speaker) output a test tone in turn.
• Press h to increase the value.
• Press l to decrease the value.
>CANCEL
Choices: SET, CANCEL
• Select “SET” to apply the settings you made.
• Select “CANCEL” to cancel the setup procedure
without making any changes.
y
You can also press P MENU to cancel the setup procedure.
8
Press G ENTER to confirm your selection.
If you selected “SET” in step 7, each speaker outputs
a test tone twice in turn. “CHECK:TestTone” appears
in the front panel display for a few seconds and then
“CHECK OK?” appears in the front panel display.
FR ----||---• Select “FR” to adjust the balance between the front
left and right speakers.
• Select “C” to adjust the balance between the front
left and center speakers.
• Select “SL” to adjust the balance between the front
left and surround left speakers.
• Select “SR” to adjust the balance between the
surround left and surround right speakers.
• Select “SW” to adjust the balance between the
front left speaker and the subwoofer.
CHECK:TestTone
y
• Check the speaker connections (see page 5) and adjust the
“SPEAKERS” settings back in step 6, if necessary.
• The indicator of the speaker currently outputting the test
tone flashes in the front panel display.
9
Press Gl / h to select the desired setting.
Note
CHECK OK? .. YES
Choices: YES, NO
• Select “YES” to complete the setup procedure if
the test tone levels from each speaker were
satisfactory.
• Select “NO” to proceed to the speaker level
adjustment menu to balance the output level of
each speaker.
22 En
The available speaker channels differ depending on the
setting of the speakers.
12
Press P MENU to exit from “BASIC SETUP”.
SELECTING THE SCENE TEMPLATES
Selecting the SCENE templates
This unit is equipped with 13 preset SCENE templates for
various situations of using this unit. As the initial factory
setting, the following SCENE templates are assigned to
each SCENE button:
2
Press D INPUT l / h (or press DAMP and
then G l / h) to select the desired template.
l
SCENE 1: DVD Viewing
SCENE 2: Disc Listening
SCENE 3: TV Viewing
SCENE 4: Radio Listening
INPUT
h
Front panel
or
If you want to use other SCENE templates, you can select
the desired SCENE templates from the SCENE template
library and assign the templates to the selected SCENE
buttons on the front panel and the remote control.
AMP
ENTER
Select the desired SCENE template
BASIC
OPERATION
Remote control
1
SCENE template library
(Image)
Assign the
SCENE template
to the SCENE
button
Selecting the desired SCENE
template
1
Press and hold the desired F SCENE (or
E SCENE) button for 3 seconds.
The indicator on the selected SCENE button on the
front panel starts to flash, and the name of currently
assigned SCENE template appears in the front panel
display.
3 seconds
3 seconds
1
or
1
Front panel
Remote control
DVD MovieView
3
Press the F SCENE (or E SCENE) button
again to confirm the selection.
The selected SCENE template is assigned to the
button.
1
Front panel
or
1
Remote control
Notes
• If you do not carry out any operation within 30 seconds from
the last operation in these steps, this procedure is automatically
canceled.
• Once the desired SCENE templates are assigned to the
corresponding SCENE buttons, you may need to set the input
source of the SCENE template on the remote control. See
page 51 for details.
1
Flashes
English
DVD Viewing
23 En
Selecting the SCENE templates
■ Which SCENE template would you like to select?
Which source do you like to
play back?
Video sources
(DVD video,
Recorded video)
Which component do you
like for playback?
DVD
SCENE templates
DVD Viewing
Default SCENE
buttons
1
DVD Movie Viewing
DVD Live Viewing
Music discs (CD,
SA-CD or DVD-Audio)
DVR
DVR Viewing
DVD
Music Disc Listening
Disc Listening
CD
2
CD Listening
CD Music Listening
Radio programs
TUNER (FM/AM)
XM*
TV programs
DTV/CBL
Radio Listening
4
XM Listening
TV Viewing
3
TV Sports Viewing
Video games
V-AUX
Game Playing
Note
*
To enjoy XM Satellite Radio programs, you need to connect the XM Mini-Tuner Dock (sold separately) to this unit (see page 37).
y
You can create your original SCENE templates by editing the preset SCENE templates. See page 26 for details.
24 En
Selecting the SCENE templates
■ Preset SCENE template descriptions
SCENE template
CD Music Listening
Features
Select this SCENE template when you play back music source as
the back ground music on your CD player.
Input source
Playback mode
CD
5ch Stereo
DVD Viewing (SCENE 1 as the default setting)
Select this SCENE template when you play back general contents
on your DVD player.
DVD
STRAIGHT
DVD Movie Viewing
Radio Listening
(SCENE 4 as the default setting)
Select this SCENE template when you enjoy FM or AM radio
programs.
TUNER
Select this SCENE template when you play back movies on your
DVD player.
DVD
MUSIC ENHANCER
5ch STEREO
XM Listening
Movie Dramatic
Select this SCENE template when you enjoy XM Satellite Radio
programs.
DVD Live Viewing
DVD
Pop/Rock
TV Viewing (SCENE 3 as the default setting)
Select this SCENE template when you enjoy TV programs.
DVR Viewing
DTV/CBL
Select this SCENE template when you play back movies on your
digital video recorder.
DVR
Music Disc Listening
STRAIGHT
TV Sports Viewing
Movie Dramatic
Select this SCENE template when you enjoy sports programs on
TV.
DTV/CBL
Select this SCENE template when you play back music discs on
your DVD player.
DVD
MUSIC ENHANCER
5ch STEREO
XM
BASIC
OPERATION
Select this SCENE template when you enjoy music live video on
your DVD player.
TV Sports
Game Playing
2ch Stereo
Select this SCENE template when you play video games.
Disc Listening
(SCENE 2 as the default setting)
V-AUX
Game
Select this SCENE template when you play back music sources as
the back ground music on your DVD player.
DVD
5ch Stereo
CD Listening
Select this SCENE template when you play back music discs on
your CD player.
CD
2ch Stereo
English
25 En
Selecting the SCENE templates
Creating your original SCENE
templates
2
You can create your original SCENE templates for each
SCENE button. You can refer to the preset 13 SCENE
templates to create the original SCENE templates.
■ Customizing the preset SCENE
templates
• The input source component
• The active sound field programs or STRAIGHT
mode
• The night listening mode setting (see page 28)
− SYSTEM: Keeps the current night listening
mode.
− CINEMA: Sets the night listening mode to the
CINEMA mode.
− MUSIC: Sets the night listening mode to the
MUSIC mode.
Use this feature to customize the preset SCENE templates.
Select the desired SCENE
template
Create an original SCENE
template
SCENE template library
(Image)
Press G k / n to select the desired parameter
of the SCENE template and then G l / h to
select the desired value of the selected
parameter.
You can adjust the following parameters for a SCENE
template:
3
Press the E SCENE button again to confirm
the edit.
1
1
Assign the SCENE
template to the SCENE
button
1
Press and hold the desired E SCENE button
for 3 seconds and then press D AMP.
The SCENE template customizing screen appears on
the front panel display.
1
AMP
3 seconds
Note
When the SCENE template you want to customize is not
assigned to any of the E SCENE button, press G l / h
repeatedly to recall the desired SCENE template (see
page 23).
26 En
y
An asterisk mark (*) appears by the name of the original SCENE
template.
Notes
• After changing the assignment of the SCENE template to the
E SCENE buttons, you may need to set the input source of the
SCENE template on the remote control. See page 51 for details.
• You can create a customized SCENE template for each
E SCENE button, and if you create another customized
SCENE template, this unit overwrites the old customized
SCENE template with the new one.
• The customized SCENE template is only available for the
assigned E SCENE button.
PLAYBACK
Playback
Caution
Extreme caution should be exercised when you play
back CDs encoded in DTS. If you play back a CD
encoded in DTS on a DTS-incompatible CD player,
you will only hear some unwanted noise that may
damage your speakers. Check whether your CD player
supports CDs encoded in DTS. Also, check the sound
output level of your CD player before you play back a
CD encoded in DTS.
Basic operations
1
3
Rotate 8 VOLUME (or press Q VOLUME +/
–) to adjust the volume to the desired output
level.
6
Press A PROGRAM l / h (or press D AMP
and then press I PROG l / h) repeatedly to
select the desired sound field program.
The name of the selected sound field program appears
in the front panel display.
See page 31 for details about sound field programs.
Movie Dramatic
Turn on the video monitor connected to this
unit.
Press 9 SPEAKERS repeatedly to select the
front speakers you want to use.
The respective speaker indicators lights up in the
front panel display.
Press D INPUT l / h repeatedly (or press
one of the input selector buttons (C)) to
select the desired input source.
The name of the currently selected input source
appears in the front panel display for a few seconds.
Available input source
DVR
V-AUX
DTV/CBL
DVD
MD/CD-R
TUNER
CD
XM
INPUT:DVD
Currently selected
surround field program
Notes
• Choose a sound field program based on your listening
preference, not merely on the name of the program.
• When you select an input source, this unit automatically selects
the last sound field program used with the corresponding input
source.
• Sound field programs cannot be selected when the component
connected to the MULTI CH INPUT jacks is selected as the
input source (see page 28).
• When PCM signals with a sampling frequency higher than 48
kHz are input, this unit is automatically set to the “STRAIGHT”
mode (see page 33).
• To display information about the currently selected input source
in the front panel display, see page 30 for details.
BASIC
OPERATION
2
5
■ Guide to contents
Currently selected input source
When you want to...
4
Start playback on the selected component or
select a broadcast station.
• Refer to the operating instructions for the source
component.
• See page 34 for details about FM/AM tuning
instructions.
• See page 37 for details about XM Satellite Radio
tuning instructions.
See
page
Adjust the tonal quality of the front speakers
29
Edit parameters of sound field programs
32
Enjoy the sources which have wide dynamic range at
night
28
Use headphones
28
Select a decoder to play back sources with
32
Set this unit to the standby mode automatically
30
English
27 En
Playback
■ Selecting the component connected to
the MULTI CH INPUT jacks as the input
source
Additional operations
■ Using your headphones
Connect a pair of headphones with a stereo
analog audio cable plug to the PHONES jack on
the front panel.
VOLUME
FM/AM
CATEGORY
A/B/C/D/E
l
PRESET/TUNING/CH
h
MEMORY
y
DISPLAY
TUNING AUTO/MAN'L
SCENE
1
l
PHONES
SILENT CINEMA
SPEAKERS
A/B/OFF
TONE CONTROL
PROGRAM
2
3
STRAIGHT
NIGHT
h
Press D INPUT l / h repeatedly (or press
A MULTI CH IN) so that “MULTI CH” appears in
the front panel display.
Use “MULTI CH SET” menu in “INPUT MENU” to set the
parameter for MULTI CH INPUT (see page 49).
STANDBY
/ON
EDIT
SEARCH MODE
PRESET/TUNING
Use this feature to select the component connected to the
MULTI CH INPUT jacks (see page 17) as the input
source.
4
l
INPUT
VIDEO AUX
h
AUDIO SELECT
VIDEO
L
AUDIO
R
PORTABLE
EFFECT
Notes
• Sound field programs mode cannot be selected when the
component connected to the MULTI CH INPUT jacks is
selected as the input source.
• When headphones are used, signals are output only from the
front left and right channels.
■ Selecting the night listening mode
y
When you select a sound field program, SILENT CINEMA mode
activates automatically (see page 33).
Notes
• When you connect headphones, no signals are output at the
speaker terminals.
• All Dolby Digital and DTS audio signals are mixed down to the
left and right headphone channels.
■ Muting the audio output
Press NMUTE to mute the audio output.
Press NMUTE again to resume the audio output.
y
• You can also rotate 8 VOLUME (or press QVOLUME +/–) to
resume the audio output.
• You can adjust the muting level by using “MUTE TYP.” in
“SOUND MENU” (see page 48).
• The MUTE indicator flashes in the front panel display when the
audio output is muted and disappears from the front panel
display when the audio output is resumed.
28 En
The night listening modes are designed to improve
listenability at lower volumes or at night.
1
Press DAMP and then press KNIGHT
repeatedly to select “NIGHT:CINEMA” or
“NIGHT:MUSIC”.
Choices: NIGHT:CINEMA, NIGHT:MUSIC,
NIGHT OFF
• Select “NIGHT:CINEMA” to reduce the dynamic
range of film soundtracks and make dialog easier to
hear at lower volumes.
• Select “NIGHT:MUSIC” to preserve ease-oflistening for all sounds.
• Select “NIGHT OFF” if you do not want to use this
feature.
y
When a night listening mode is selected, the NIGHT
indicator lights up in the front panel display.
Playback
2
■ Adjusting the tonal quality
Press Gl / h to adjust the effect level while
“NIGHT:CINEMA” or “NIGHT:MUSIC” is
displayed in the front panel display.
Choices: MIN, MID, MAX
• Select “MIN” for minimum compression.
• Select “MID” for standard compression.
• Select “MAX” for maximum compression.
y
“NIGHT:CINEMA” and “NIGHT:MUSIC” adjustments are
stored independently.
Notes
Use this feature to adjust the balance of bass and treble for
the front left and right speaker channels.
Press 0 TONE CONTROL repeatedly to select
“BASS” or “TREBLE” and then press
A PROGRAM l / h to adjust the corresponding
frequency response level.
• Select “BASS” to adjust the low-frequency response.
• Select “TREBLE” to adjust the high-frequency
response.
Notes
• You cannot use the night listening modes in the following cases:
– when the component connected to the MULTI CH INPUT
jacks is selected as the input source.
– when headphones are connected to the PHONES jack.
• The night listening modes may vary in effectiveness depending
on the input source and surround sound settings you use.
This unit comes with a variety of input jacks. Use this
feature (audio input jack select) to switch the input jack
assigned to an input source when more than one jacks are
assigned to an input source.
y
• We recommend setting audio input jack select to “AUTO” in
most cases.
• You can adjust the default audio input jack select of this unit by
using “AUDIO SELECT” in “OPTION MENU” (see page 50).
■ Adjusting speaker levels during
playback
You can adjust the output level of each speaker while
listening to a music source.
Note
This operation will override the level adjustment made in “SP
LEVEL” (see page 46).
1
Press E AUDIO SELECT (or B AUDIO SEL)
repeatedly to select the desired Audio input jack
select setting.
DVR
V-AUX
DTV/CBL
DVD
MD/CD-R
TUNER
CD
XM
Audio input jack
select setting
ANALOG
Automatically selects input signals in the
following order:
(1) Digital signals
(2) Analog signals
Selects only analog signals. If no analog
signals are input, no sound is output.
Adjusted speaker
FRONT L
Front left speaker
FRONT R
Front right speaker
CENTER
Center speaker
SUR.L
Surround left speaker
SUR.R
Surround right speaker
SWFR
Subwoofer
y
Once you press FLEVEL on the remote control, you can
also select the speaker by pressing G k / n.
2
Note
This feature is not available when no digital input jack are
assigned to the currently selected input source.
Press DAMP and then press FLEVEL
repeatedly to select the speaker you want to
adjust.
Display
A.SEL:AUTO
AUTO
BASIC
OPERATION
■ Selecting audio input jacks
(AUDIO SELECT)
• Speaker and headphone adjustments are stored independently.
• If you increase or decrease the high-frequency or low-frequency
sound to an extreme level, the tonal quality of the surround
speakers may not match that of the front left and right speakers.
Press G l / h on the remote control to
adjust the speaker output level.
The control range is from –10 dB to +10 dB.
y
29 En
English
You can press 4 A/B/C/D/E to select a speaker and then
5 PRESET/TUNING/CH l / h to adjust the speaker output
level.
Playback
■ Displaying the signal information
■ Using the sleep timer
You can display the format, sampling frequency, channel,
bit rate and flag data of the current input signal.
Use this feature to automatically set this unit to the
standby mode after a certain amount of time.
1
Press DAMP and then press OSLEEP
repeatedly to set the amount of time.
Each time you press O SLEEP, the front panel display
changes as shown below.
Press DAMP and then press PMENU on
the remote control.
“BASIC SETUP” appears in the front panel display.
;BASIC SETUP
2
3
Press Gk / n repeatedly to select “SIGNAL
INFO” and then press GENTER.
Press Gk / n to switch the displayed
information.
The following information about the input source
appears in the front panel display.
Display
4
Description
FORMAT
Signal format.
SAMPL.
The number of samples per second taken
from a continuous signal to make a discrete
signal.
CH
The number of source channels in the input
signal (front/surround/LFE).
B.RATE
The number of bits passing a given point
per second.
FLAG
Flag data encoded in DTS, Dolby Digital,
or PCM signals that cue this unit to
automatically switch decoders.
Press P MENU to exit.
SLEEP 120min
SLEEP OFF
SLEEP 90min
SLEEP 30min
SLEEP 60min
The SLEEP indicator flashes while you are switching the
amount of time for the sleep timer. Once the sleep timer is
set, the SLEEP indicator lights up in the front panel
display, and the display returns to the selected sound field
program.
y
• To cancel the sleep timer, press O SLEEP on the remote
control repeatedly until “SLEEP OFF” appears in the front
panel display.
• You can also cancel the sleep timer setting by pressing
1 STANDBY/ON (or M STANDBY) to set this unit to the
standby mode.
■ Playing video sources in the
background
You can combine a video image from a video source with
sound from an audio source. For example, you can enjoy
listening to classical music while viewing beautiful
scenery from the video source on the video monitor.
Press the input selector buttons on the remote
control to select a video source and then an
audio source.
MULTI CH IN
CD
MD/CD-R
TUNER
DVD
DTV/CBL
DVR
V-AUX
XM
Audio sources
Video sources
30 En
SOUND FIELD PROGRAMS
Sound field programs
This unit is equipped with a variety of precise digital
decoders that allow you to enjoy multi-channel playback
from almost any stereo or multi-channel sound source.
Press A PROGRAM l / h (or press D AMP and
then press IPROG l / h repeatedly).
The name of the selected sound field program appears in
the front panel display.
Notes
• Sound field programs cannot be selected when the component
connected to the MULTI CH INPUT jacks is selected as the
input source (see page 28).
• When PCM signals with a sampling frequency higher than 48
kHz are input, this unit is automatically set to the “STRAIGHT”
mode (see page 33).
y
• Choose a sound field program based on your listening
preference, not merely on the name of the program itself.
• You can select “Music Enh. 2ch” and “Music Enh. 5ch” by
pressing T ENHANCER on the remote control repeatedly.
• When you select an input source, this unit automatically selects
the last sound field program used with the corresponding input
source.
Category
MUSIC
Program
Features
Pop/Rock
CINEMA DSP processing. This program presents an image of pop, rock, or jazz live concert. The
sound field reproduces the spaciousness of a massive pavilion with an emphasis on the vividness of
vocals on the stage and solo instruments and the beats of rhythm instruments.
Hall
HiFi DSP processing. This sound field is suitable for classic and orchestral music. The program
uses data collected in a large concert hall in Munich. You can enjoy delicate and beautiful
reverberation and a majestic atmosphere.
Jazz
HiFi DSP processing. The sound field is suitable for jazz and fusion music.
BASIC
OPERATION
Sound field program descriptions
It uses data collected in a famous jazz club in New York. You can enjoy clear reverberation.
ENTERTAIN
MOVIE
STEREO
ENHANCER
Game
CINEMA DSP processing. You can enjoy dynamic and thrilling sound effects as you play games.
The program lets you feel the depth and three-dimensional surrounding sounds of the field where
you are playing, and offers cinema-like surrounding sound effects for the scenes of movies.
TV Sports
CINEMA DSP processing. You can enjoy sports relays broadcast in stereo and variety shows with
a live sound environment. For sports relays, the voices of commentators and announcers come
clearly from the center; the cheers and atmosphere in the stadium spread around within a
comfortable range, and you can feel like as if you are in the stadium.
Movie Spacious
CINEMA DSP processing. The sound field is suitable for movies with an emphasis on spectacular
sound effects, and is a perfect fit with a wide screen. The program reproduces a wide dynamic
range from minimum sound effects to powerful sounds.
Movie Dramatic
CINEMA DSP processing. This sound field is also suitable for movies with an emphasis on threedimensional sound effects. It restrains reverberation to an moderate extent, but reproduces sound
effects and background music in a soft, three-dimensional manner with clarity and center
orientation of voices as pivots.
2ch Stereo
Downmixes multi-channel sources to 2 channel or plays back 2-channel sources as they are.
5ch Stereo
Using this program increases the listening position range. This is a sound field suitable for
background music at parties.
Music Enh. 2ch
Music Enh. 5ch
Select these programs to play back compression artifacts (such as the MP3 format) in 2-channel or
5-channel stereo. This program enhances your listening experience by regenerating the missing
harmonics in a compression artifact.
Note
31 En
English
The sound field programs of this unit are recreations of real-world acoustic environments made from precise measurements taken in the
actual concert hall, music venue, movie theater, etc. Thus, you may notice variations in the strength of the reflections coming from the
front, back, left and right.
Sound field programs
■ Selecting decoders for 2-channel
sources (surround decode mode)
y
Signals input from 2-channel sources can also be played
back on multi-channels.
For Pop/Rock, Hall, Jazz, Game, TV Sports,
Movie Spacious and Movie Dramatic:
Press D AMP and then press J SUR. DECODE
repeatedly to select a decoder.
You can select from the following decoders depending on
the type of source you are playing and your personal
preference.
STANDARD
Functions
PRO LOGIC
Dolby Pro Logic processing for any
sources
PLII Movie
Dolby Pro Logic II processing for
movie sources
PLII Music
Dolby Pro Logic II processing for
music sources
PLII Game
Dolby Pro Logic II processing for
game sources
Neural
Neural Surround processing for any
sources
■ Editing sound fields parameters
You can enjoy good quality sound with the factory preset
parameters. Although you do not have to change the initial
settings, you can change some of the parameters to better
suit the input source or your listening room.
1
2
While listening to a source, press D AMP
and then press Gk / n to select the desired
parameter.
Press Gl / h to change the parameter
value.
Note
You cannot change parameter values when “MEM. GUARD” in
“OPTION MENU” is set to “ON” (see page 50).
32 En
Initial settings are indicated in bold under each parameter.
DSP level DSP LEVEL
Function:
Adjusts the effect level.
Choices:
MIN, MID, MAX
For PRO LOGIC II Music:
Panorama PANORAMA
Function:
Sends stereo signals to the surround
speakers as well as the front speakers
for a wraparound effect.
Choices:
OFF, ON
Dimension DIMENSION
Function:
Gradually adjusts the sound field
either towards the front or towards the
rear.
Control range: –3 (towards the rear) to +3 (towards
the front), initial setting is STD
(standard).
Center width CT WIDTH
Function:
Adjusts the center image from all
three front speakers to varying
degrees. A larger value adjusts the
center image towards the front left and
right speakers.
Control range: 0 (center channel sound is output only
from center speaker) to 7 (center
channel sound is output only from
front left and right speakers), initial
setting is 3.
For Music Enh. 2ch and Music Enh. 5ch
Effect level
Function:
Choices:
Adjusts the effect level.
LOW, HIGH
Sound field programs
■ Using sound field programs without
surround speakers (Virtual CINEMA DSP)
Virtual CINEMA DSP allows you to enjoy the CINEMA
DSP programs without surround speakers by creating
virtual speakers.
If you set “SUR. LR” to “NONE” (see page 45), Virtual
CINEMA DSP activates automatically whenever you
select a CINEMA DSP or HiFi DSP program (see
page 31).
Note
Virtual CINEMA DSP will not activate even when “SUR. LR” is
set to “NONE” (see page 45) in the following cases:
– when “5ch Stereo” (see page 31) is selected.
– when headphones are connected to the PHONES jack.
■ Enjoying multi-channel sources and
sound field programs with headphones
(SILENT CINEMA)
SILENT CINEMA allows you to enjoy multi-channel
music or movie sound, including Dolby Digital and DTS
sources, through ordinary headphones. SILENT CINEMA
activates automatically whenever you connect headphones
to the PHONES jack while listening to CINEMA DSP or
HiFi DSP sound field programs (see page 31). When
activated, the SILENT CINEMA indicator lights up in the
front panel display.
Note
SILENT CINEMA does not activate when the component
connected to the MULTI CH INPUT jacks is selected as the input
source (see page 28).
■ Enjoying unprocessed input sources
(Straight decoding mode)
BASIC
OPERATION
When this unit is in the “STRAIGHT” mode, multichannel sources are decoded straight into the appropriate
channels without any additional effect processing. 2channel stereo sources are output from only the front left
and right speakers.
Press B STRAIGHT (or press D AMP and then
S STRAIGHT) to select “STRAIGHT”.
To deactivate the “STRAIGHT” mode, press
B STRAIGHT (or S STRAIGHT) again so that
“STRAIGHT” disappears from the front panel display.
English
33 En
FM/AM TUNING
FM/AM tuning
There are 2 tuning methods: automatic and manual. Automatic tuning is effective when station signals are strong and
there is no interference. If the signal from the station you want to select is weak, tune into it manually. You can also use
the automatic and manual preset tuning features to store up to 40 stations.
Automatic tuning
Manual tuning
Automatic tuning is effective when station signals are
strong and there is no interference.
1
Press D INPUT l / h repeatedly so that
“TUNER” is displayed in the front panel
display.
2
Press 3 FM/AM to select the reception band
(FM or AM).
3
Press 7 TUNING AUTO/MAN’L so that the
AUTO indicator lights up in the front panel
display.
Lights up
If the signal received from the station you want to select is
weak, tune into it manually.
Note
Manually tuning into an FM station automatically switches the
tuner to monaural reception to increase the signal quality.
1
Press D INPUT l / h repeatedly so that
“TUNER” is displayed in the front panel
display.
2
Press 3 FM/AM to select the reception band
(FM or AM).
3
Press 7 TUNING AUTO/MAN’L so that the
AUTO indicator disappears from the front
panel display.
AUTO
A
AM 1440 kHz
No colon (:)
A
If a colon (:) appears in the front panel display,
automatic tuning is not possible. Press 2 PRESET/
TUNING to turn the colon (:) off.
4
Press 5 PRESET/TUNING/CH l / h once
to begin automatic tuning.
When this unit is tuned into a station, the TUNED
indicator lights up and the frequency of the received
station is shown in the front panel display.
Lights up
AUTO TUNED
A
34 En
AM 1530 kHz
AM 1440 kHz
No colon (:)
If a colon (:) appears in the front panel display,
manual tuning is not possible. Press 2 PRESET/
TUNING to turn the colon (:) off.
4
Press 5 PRESET/TUNING/CH l / h to
tune into the desired station manually.
You can hold down the button to continue searching.
FM/AM tuning
Automatic preset tuning
Manual preset tuning
You can use the automatic preset tuning feature to store
FM stations with strong signals up to 40 (A1 to E8: 8
preset station numbers in each of the 5 preset station
groups) of those stations in order. You can then recall any
preset station easily by selecting the preset station number.
1
2
3
Press D INPUT l / h repeatedly so that
“TUNER” is displayed in the front panel
display.
Press 3 FM/AM to select “FM” as the
reception band.
You can also store up to 40 stations (A1 to E8: 8 preset
station numbers in each of the 5 preset station groups)
manually.
Tune into a station automatically or manually.
See page 34 for tuning instructions.
2
Press 6 MEMORY.
The MEMORY indicator flashes in the front panel
display for approximately 10 seconds.
3
Press 4 A/B/C/D/E and 5 PRESET/
TUNING/CH l / h repeatedly to select a
preset station group (A1 to E8) while the
MEMORY indicator is flashing.
Check that the colon (:) appears in the front panel
display.
Press and hold 6 MEMORY for more than 3
seconds.
The preset station number as well as the MEMORY
and AUTO indicators flashes. After approximately 5
seconds, automatic presetting starts from the current
frequency and proceeds toward the higher
frequencies.
Flashes
TUNED
C3 : AM
Flash
AUTO
A1:FM 87.50MHz
When automatic preset tuning is completed, the front
panel display shows the frequency of the last preset
station.
630 kHz
Preset station number
MEMORY
Flashes
MEMORY
BASIC
OPERATION
1
4
Press 6 MEMORY while the MEMORY
indicator is flashing.
The station band and frequency appear in the front
panel display with the preset station group and
number you have selected.
y
You can select the preset station group and the preset station
number where the first received station will be stored by pressing
4 A/B/C/D/E and then 5 PRESET/TUNING/CH l / h.
Notes
• Any stored station data existing under a preset station number is
cleared when you store a new station under the same preset
station number.
• Only FM stations with sufficient signal strength are stored
automatically by automatic preset tuning. If the station you
want to store is weak in signal strength, tune into it manually
and store it as described in “Manual preset tuning” on this page.
TUNED
C3 : AM
630 kHz
The displayed station has been stored as C3.
Notes
• Any stored station data existing under a preset station number is
cleared when you store a new station under the same preset
station number.
• The reception mode (stereo or monaural) is stored along with
the station frequency.
English
35 En
FM/AM tuning
Selecting preset stations
You can tune into any desired station simply by selecting
the preset station group and number under which it was
stored.
y
When performing this operation with the remote control, press
C TUNER to select “TUNER” as the input source.
1
Press 4 A/B/C/D/E (or G A-E/CAT. l / h)
repeatedly to select the desired preset
station group (A to E).
The preset station group letter appears in the front
panel display and changes each time you press the
button.
Exchanging preset stations
You can exchange the assignments of two preset stations
with each other. The example below describes the
procedure to exchange preset station “E1” with “A5”.
1
Select preset station “E1” using 4 A/B/C/D/E
and 5 PRESET/TUNING/CH l / h.
See “Selecting preset stations” on this page.
2
Press and hold 2 PRESET/TUNING for
more than 3 seconds.
“E1” and the MEMORY indicator flash in the front
panel display.
Flashes
2
Press 5 PRESET/TUNING/CH l / h (or
G PRESET/CH k / n) to select the desired
preset station number (1 to 8).
The preset station group and number appear in the
front panel display along with the station band and
frequency.
MEMORY
E1 : FM 87.50MHz
Flashes
3
E1 : FM 87.50MHz
y
Select preset station “A5” using 4 A/B/C/D/
E and 5 PRESET/TUNING/CH l / h.
“A5” and the MEMORY indicator flash in the front
panel display.
See “Selecting preset stations” on this page.
You can select the desired preset station number (1 to 8) directly
by pressing the numeric buttons on the remote control.
Flashes
MEMORY
A5 : FM 90.60MHz
Flashes
4
36 En
Press 2 PRESET/TUNING again.
“EDIT E1–A5” appears in the front panel display and
the assignments of the two preset stations are
exchanged.
XM SATELLITE RADIO TUNING
XM Satellite Radio tuning
XM Satellite Radio offers an extraordinary variety of
commercial-free music, plus the best in sports, news, talk
and entertainment. XM is broadcast in superior digital
audio from coast to coast. From rock to reggae, from
classical to hip hop, XM has something for every music
fan. XM’s dedication to playing the richest selection of
music is matched by its passion for live sporting events,
talk radio, up-to-the-minute news, stand-up comedy,
children’s programming, and much more.
Connecting the XM Mini-Tuner Dock
Connect XM Mini-Tuner and XM Dock (sold
separately) to the XM jack on the rear panel of
this unit.
For details, see the operating instructions provided with
XM Mini-Tuner Dock.
XM Mini-Tuner and XM Dock
(sold separately)
For U.S. customers, information about XM Satellite Radio
is available online at www.xmradio.com.
For Canadian customers, information about XM Canada is
online at www.xmradio.ca.
BASIC
OPERATION
This unit is equipped with the Neural Surround decoder
that plays back the XM HD surround sound content of the
XM Satellite Radio broadcasts in multi-channels, resulting
in a full surround sound experience.
XM
DVD
Note
The XM Satellite Radio service is only available in the 48
contiguous United States (not available in Alaska and Hawaii)
and Canada.
■ Information from XM Satellite Radio Inc.
Hardware and required monthly subscription sold
separately. Other fees and taxes, including a one-time
activation fee may apply. Subscription fee is consumer
only. All fees and programming subject to change.
Subscriptions subject to Customer Agreement available at
xmradio.com (US residents) and xmradio.ca (Canadian
residents). Only available in the 48 contiguous United
States and Canada. ©2006 XM Satellite Radio Inc. All
rights reserved. All other trademarks are the property of
their respective owners.
PR
y
• To ensure optimal reception of the XM Satellite Radio signals,
the XM Mini-Tuner Dock must be placed at or near a southerly
facing window with no obstacles in the path to the sky. You can
mount it indoors or outdoors.
• Use the “XM ANT.” parameter in “OPTION MENU” (see
page 50) to display the XM Satellite Radio reception level in the
front panel display. For the best reception, orient the connected
XM Mini-Tuner so that a value of 60% or more is displayed.
Note
If “CHECK ANTENNA” appears in the front panel display, the
XM Mini-Tuner Dock may not be connected to the XM jack on
the rear panel of this unit properly. See “Connecting the XM
Mini-Tuner Dock” on this page and check the connection.
English
37 En
XM Satellite Radio tuning
Activating XM Satellite Radio
Once you have installed the XM Mini-Tuner Dock,
inserted the XM Mini-Tuner, connected the XM Dock to
your XM Ready® home audio system, and installed the
antenna, you are ready to subscribe and begin receiving
XM programming. There are three places to find your
eight character XM Radio ID: on the XM Mini-Tuner, on
the XM Mini-Tuner package, and on XM Channel 0.
Record the Radio ID in the following eight squares for
reference.
Basic XM Satellite Radio
operations
1
Press D INPUT l / h repeatedly (or press
C XM) to select “XM” as the input source.
The cursor on the left of the XM indicator lights up in
the front panel display and the XM Satellite Radio
information (such as channel number, channel name,
category, artist name, or song title) for the currently
selected channel appears in the front panel display.
Lights up
DVR
Note
The XM Radio ID does not use the letters “I”, “O”, “S” or “F”.
Activate your XM Satellite Radio service in the U.S. online at
http://www.xmradio.com/ or call 1-800-XM-RADIO (1-800-9672346). You will need a major credit card. XM will send a signal
from the satellites to activate the full channel lineup. Activation
normally takes 10 to 15 minutes, but during peak busy periods
you may need to keep your XM Ready home audio system on for
up to an hour. When you can access the full channel lineup on
your XM Ready home audio system you are done. For more
information or to subscribe in Canada, visit XM on the Web at
www.xmradio.ca or call XM’s Listener Care at 1-877-GETXMSR (1-877-438-9677).
V-AUX
DTV/CBL
DVD
MD/CD-R
TUNER
CD
XM
[001] Preview
y
When you select “XM” as the input source, this unit
automatically recalls the previously selected channel.
2
Search for a channel by using one of the XM
Satellite Radio search modes.
• To select a channel from the all channel list, see
“All Channel Search mode” on page 39.
• To select a channel by category, see “Category
Search mode” on page 39.
• To select a channel from the preset channels, see
“Preset Search mode” on page 39.
• To select the desired channel directly by entering
the channel number, see “Direct Number Access
mode” on page 39.
y
• You can use the Neural Surround decoder to enjoy the XM
HD surround sound content of the XM Satellite Radio
broadcasts in multi-channels (see page 32).
• You can set the XM Satellite Radio preset channels (see
page 40).
• You can display the XM Satellite Radio information in the
front panel display (see page 41).
38 En
XM Satellite Radio tuning
y
When performing these operations with the remote control, press
C XM to select “XM” as the input source.
3
■ All Channel Search mode
1
2
Press 2 SEARCH MODE (or P SRCH
MODE) repeatedly to select “ALL CH
SEARCH”.
Press 5 PRESET/TUNING/CH l / h (or
G PRESET/CH k / n) repeatedly to search
for a channel within all channels.
y
y
You can also select the preset channel number directly by
pressing the numeric buttons (1 to 8) on the remote control.
■ Direct Number Access mode
1
Press P SRCH MODE repeatedly to select
“ALL CH SEARCH” or “CAT SEARCH”.
2
Press the numeric buttons (V) to enter the
desired three-digit channel number.
For example, to enter the number 123, press the
numeric buttons as shown below.
• You can search for a channel quickly by pressing and holding
5 PRESET/TUNING/CH l / h (or G PRESET/CH k / n).
• To display the XM Radio ID number displayed in the front
panel display, select channel “0”.
Press 2 SEARCH MODE (or P SRCH
MODE) repeatedly to select “CAT SEARCH”.
2
Press 4 CATEGORY (or G A-E/CAT. l / h)
repeatedly to change the channel category.
3
Press 5 PRESET/TUNING/CH l / h (or
G PRESET/CH k / n) repeatedly to search
for a channel within the selected channel
category.
l
h
ENHANCER
1
2
3
BASIC
OPERATION
■ Category Search mode
1
Press 5 PRESET/TUNING/CH l / h (or
G PRESET/CH k / n) repeatedly to change
the preset channel number (1 to 8).
The display changes as follows.
<XM> --1
<XM> -12
y
You can search for a channel quickly by pressing and holding
5 PRESET/TUNING/CH l / h (or G PRESET/CH k / n).
■ Preset Search mode
Prior to selecting a preset channel in the Preset Search
mode, you must preset XM Satellite Radio channels. For
details, see “Setting XM Satellite Radio preset channels”
on page 40.
y
All preset channels (A1 to E8) recalls “001 Preview” by the initial
factory setting.
Press 2 SEARCH MODE (or P SRCH
MODE) repeatedly to select “PRESET
SEARCH”.
2
Press 4 CATEGORY (or G A-E/CAT. l / h)
repeatedly to change the preset channel
group (A to E).
y
• To enter a one-digit or two-digit channel number, press the
numeric buttons (V) and then press W ENT. to confirm the
input number. Instead of pressing W ENT. to tune into the
channel immediately, you can wait a few seconds until this unit
confirms the entered channel number.
• If no button is pressed within a few seconds after you enter a
one-digit or two-digit number, this unit automatically confirms
the entered channel number.
• Pressing a button other than the numeric buttons (V) or
W ENT. cancels the Direct Number Access mode procedure.
English
1
<XM>123
39 En
XM Satellite Radio tuning
Setting XM Satellite Radio preset
channels
4
You can use this feature to store up to 40 XM Satellite
Radio channels (A1 to E8: 8 preset channel numbers in
each of the 5 preset channel groups). You can then recall
any preset channel easily by selecting the preset channel
group and number as described in “Preset Search mode”
on page 39.
Press 5 PRESET/TUNING/CH l / h (or
G PRESET/CH k / n) repeatedly to select a
preset channel number (1 to 8) while the
MEMORY indicator is flashing.
The preset channel number appears in the front panel
display.
Flashes
MEMORY
1
2
Search for a channel you want to set as a
preset channel by using one of the XM
Satellite Radio search modes.
See “Basic XM Satellite Radio operations” on
page 38 for details.
Press 6 MEMORY (or H XM MEMORY).
The MEMORY indicator flashes in the front panel
display for approximately 10 seconds.
Note
C5 [043] XMU
Currently selected preset channel number
5
Press 6 MEMORY (or H XM MEMORY) to
set the selected XM Satellite Radio channel
as a preset channel while the MEMORY
indicator is flashing.
A colon (:) appears next to the preset channel number
for confirmation, and the MEMORY indicator turns
off in the front panel display.
You must proceed to and carry out steps 3 through 5 while
the MEMORY indicator is flashing in the front panel
display.
3
Press 4 CATEGORY (or G A-E/CAT. l / h)
repeatedly to select a preset channel group
(A to E) while the MEMORY indicator is
flashing.
The preset channel group letter appears in the front
panel display.
Flashes
MEMORY
C
[043] XMU
Currently selected preset channel group
40 En
C5:[043] XMU
Colon (:)
Note
Once you set a new preset channel, the one previously stored in
the same preset channel group and number is cleared.
XM Satellite Radio tuning
Displaying the XM Satellite Radio
information
You can display the XM Satellite Radio information (such
as channel number, channel name, category, artist name,
or song title) for the currently selected channel in the front
panel display.
Note
If a status message or an error message appears in the front panel
display, see the “XM Satellite Radio (U.S.A. and Canada models
only)” section in “Troubleshooting” on page 59 for appropriate
remedies.
■ Displaying the XM Satellite Radio
information in the front panel display
BASIC
OPERATION
Press 7 DISPLAY (or R DISPLAY) repeatedly to
toggle between the following XM Satellite Radio
information display modes.
Channel number/name
Channel category
Artist name/song title
y
• The front panel display can indicate up to 14 alphanumeric
characters at once. You can set whether to display the XM
Satellite Radio information in the front panel display in a
continuous manner or by 14 alphanumeric characters at once by
using the “FL SCROLL” parameter in “OPTION MENU” (see
page 50).
• If the XM Satellite Radio information contains a character that
cannot be recognized by this unit, the character will be
displayed with a space.
English
41 En
RECORDING
Recording
Recording adjustments and other operations are performed from the recording components. Refer to the operating
instructions for those components.
Notes
• When this unit is set to the standby mode, you cannot record between other components connected to this unit.
• The settings of TONE CONTROL (see page 29) and VOLUME settings, speaker levels (see page 29) and the sound field programs
(see page 31) do not affect recorded material.
• The source connected to the MULTI CH INPUT jacks of this unit cannot be recorded.
• The XM Satellite Radio signals cannot be output at the AUDIO OUT (REC) jacks.
• Digital signals input at the DIGITAL INPUT jacks are not output at the analog AUDIO OUT (REC) jacks for recording. Therefore, if
your source component is connected to provide only digital signals, you cannot record the source.
• A given input source is not output on the same OUT (REC) channel.
• Once you have connected a recording component to this unit, keep the component turned on while using this unit. If the component is
turned off, this unit may distort the sound from other components.
• Check the copyright laws in your country to record from CDs, radio, etc. Recording of copyrighted material may infringe copyright
laws.
y
Do a test recording before you start an actual recording.
If you play back a video source that uses scrambled or encoded signals to prevent it from being dubbed, the picture
itself may be disturbed due to those signals.
1
Turn on all the connected components.
2
Press D INPUT l / h repeatedly (or press
one of the input selector buttons (C)) to
select the source component you want to
record from.
42 En
3
Start playback on the selected source
component or select a broadcast station.
4
Start recording on the recording component.
Set menu
Set menu
You can use the following parameters in set menu to adjust a variety of system settings and customize the way this unit
operates. Change the initial settings (indicated in bold under each parameter) to reflect the needs of your listening
environment.
■ Basic setup BASIC SETUP
Use this feature to automatically adjust speaker and system parameters (see page 21).
■ Manual setup MANUAL SETUP
Use this feature to manually adjust speaker and system parameters.
Sound menu 1 SOUND MENU
Use this menu to manually adjust any speaker settings, alter the quality and tone of the sound output by the system or
compensate for video signal processing delays when using LCD monitors or projectors.
Parameter
Page
A)SPEAKER SET
Selects the size of each speaker, the speakers for low-frequency signal output, the crossover
frequency, and the location of the front speakers connected to the FRONT B terminals.
45
B)SP LEVEL
Adjusts the output level of each speaker.
46
C)SP DISTANCE
Adjusts the distance of each speaker.
47
D)CENTER GEQ
Adjusts the tonal quality of the center speaker.
47
E)LFE LEVEL
Adjusts the output level of the LFE channel for Dolby Digital or DTS signals.
47
F)D. RANGE
Adjusts the dynamic range of Dolby Digital or DTS signals.
47
G)AUDIO SET
Adjusts the muting level, audio delay settings, maximum volume level and initial volume
level.
48
ADVANCED
OPERATION
Features
Input menu 2 INPUT MENU
Use this menu to manually reassign the input jacks, select the input mode or rename the input source.
Parameter
Features
Page
A)INPUT ASSIGN
Assigns the input jacks of this unit according to the component to be used.
48
B)INPUT RENAME
Changes the name of the input source.
49
C)VOLUME TRIM
Adjusts the output volume of each jack.
49
D)DECODER MODE
Selects the decoder mode for the sources connected to the DIGITAL INPUT jacks on the
rear panel of this unit.
49
E)MULTI CH SET
Select the video source played in the background of the sources in put from the MULTI CH
INPUT jacks.
49
English
43 En
Set menu
Option menu 3 OPTION MENU
Use this menu to manually adjust the optional system parameters.
Parameter
Features
Page
A)DISPLAY SET
Adjusts the brightness of the front panel display and the way in which the XM information
is displayed.
50
B)MEMORY GUARD
Locks sound field program parameters and other set menu settings.
50
C)AUDIO SELECT
Designates the default audio input jack select setting mode for the input sources connected
to the DIGITAL INPUT jacks when you turn on the power of this unit.
50
D)PARAM. INI
Sets all the parameters of the sound field programs to the initial factory settings.
50
E)XM RADIO SET
Displays the current reception level of the XM Satellite Radio signals.
50
Note
The “XM RADIO SET” parameter is only applicable to the U.S.A. and Canada models.
■ Signal information SIGNAL INFO
Use this feature to check audio signal information (see page 30).
Using set menu
4
Use the remote control to access and adjust each
parameter.
y
You can change the set menu parameters while this unit is
reproducing sound.
1
1 SOUND MENU
Press D AMP and then press P MENU on
the remote control.
“BASIC SETUP” appears in the front panel display.
2 INPUT MENU
. BASIC SETUP
2
Press G k / n to select “MANUAL SETUP”.
3 OPTION MENU
5
Press G k / n repeatedly and then press
G ENTER to select and enter the desired
submenu.
• Repeat steps 5 and 6 to navigate to and enter the
items you want to adjust.
• To return to the previous menu level, press H
RETURN.
6
Press G k / n to select the desired parameter
and then G l / h to change the parameter
value.
• Press G h to increase the value.
• Press G l to decrease the value.
7
Press P MENU to exit from set menu.
. MANUAL SETUP
3
Press G ENTER to enter “MANUAL SETUP”.
“1 SOUND MENU” appears in the front panel
display.
1 SOUND MENU
44 En
Press G k / n repeatedly and then press
G ENTER to select and enter the desired
menu.
The following menus appear in the front panel
display as you press G k / n repeatedly.
Set menu
1 SOUND MENU
Use this menu to manually adjust any speaker settings or
compensate for video signal processing delays when using
LCD monitors or projectors.
■ Speaker settings A)SPEAKER SET
Use this feature to manually adjust any speaker settings.
FRONT B speaker setting FRONT B
Use this feature to select the location of the front speakers
connected to the FRONT B terminals.
Choices: FRONT, ZONE B
• Select “FRONT” to turn FRONT A and B on and off
when the FRONT B speakers are set in the main zone.
• Select “ZONE B” if the speakers connected to the
FRONT B terminals are set in another zone. If FRONT
A is turned off and FRONT B is turned on, all the
speakers including the subwoofer in the main zone are
muted and this unit outputs sound at the FRONT B
terminals only.
Notes
Front speakers FRONT
Choices: SMALL, LARGE
When the front speakers are large
Select “LARGE” (large).
When the front speakers are small
Select “SMALL” (small).
Note
When “BASS OUT” is set to “FRNT” (see page 46), you can
select only “LARGE” in “FRONT”. If the value of “FRONT” is
set to a setting other than “LARGE” in advance, this unit
automatically changes the value to “LARGE”.
Center speaker CENTER
Choices: NONE, SML, LRG
When the center speaker is large
Select “LRG” (large).
When the center speaker is small
Select “SML” (small).
When you do not use the center speaker
Select “NONE” (none). The center channel signals are
directed to the front left and right speakers.
Surround left/right speakers SUR. LR
Choices: NONE, SML, LRG
ADVANCED
OPERATION
• If you connect headphones to the PHONES jack of this unit, the
sound is output from both headphones and the FRONT B
terminals when “FRONT B” is set to “ZONE B”.
• If a DSP program is selected when “FRONT B” is set to
“ZONE B”, this unit automatically enters the Virtual CINEMA
DSP mode (see page 33).
Woofer section of a speaker is 16 cm (6.5 in) or larger:
large
Woofer section of a speaker is smaller than 16 cm
(6.5 in): small
When the surround speakers are large
Select “LRG” (large).
When the surround speakers are small
Select “SML” (small).
When you do not use the surround speakers
Select “NONE” (none). This unit is set to the Virtual
CINEMA DSP mode (see page 33).
English
45 En
Set menu
LFE/Bass out BASS OUT
Use this feature to select the speakers that output the LFE
(low-frequency effect) and the low-frequency signals.
Choices: SWFR, FRNT, BOTH
y
If you are not satisfied with the bass sounds from your speakers,
you can change these settings according to your preference.
When a subwoofer is connected to this unit
and you want to get natural bass sound
Select “SWFR” (subwoofer). The LFE signals as well
as the low-frequency signals of other speakers set to
“SML” (or “SMALL”) are directed to the subwoofer.
When a subwoofer is connected to this unit
and you want to get rich bass sound
Select “BOTH” (both). The low-frequency signals of
any source are output from the subwoofer. The LFE
signals as well as the low-frequency signals of other
speakers set to “SML” (or “SMALL”) are directed to
the subwoofer. The low-frequency signals of the front
left and right channels are directed to the front left and
right speakers and the subwoofer regardless of the
“FRONT” setting (see page 45).
When you do not use a subwoofer
Select “FRNT” (front). The LFE signals, the lowfrequency signals of the front left and right channels,
and the low-frequency signals of other speakers set to
“SML” (or “SMALL”) are all directed to the front left
and right speakers regardless of the “FRONT” setting
(see page 45).
Crossover CROSSOVER
Use this feature to select a crossover frequency of all the
speakers set to “SML” (or “SMALL”) or to “NONE” in
“SPEAKER SET” (see pages 44 and 45). All frequencies
below the selected frequency will be sent to the subwoofer
or to the speakers set to “LRG” (or “LARGE”) in
“SPEAKER SET” (see pages 44 and 45).
Choices: 40Hz, 60Hz, 80Hz, 90Hz, 100Hz, 110Hz,
120Hz, 160Hz, 200Hz
Subwoofer phase SWFR PHASE
Use this feature to switch the phase of your subwoofer if
bass sounds are lacking or unclear.
Choices: NRM, REV
• Select “NRM” if you do not want to reverse the phase
of your subwoofer.
• Select “REV” to reverse the phase of your subwoofer.
46 En
■ Speaker level
B)SP LEVEL
Use this feature to manually adjust the output level of each
speaker.
Control range: –10 to +10 dB
Control step: 1 dB
Initial setting: 0 dB
SP LEVEL
Adjusted speaker
FL
Front left speaker
FR
Front right speaker
C
Center speaker
SL
Surround left speaker
SR
Surround right speaker
SWFR
Subwoofer
Note
The available speaker channels differ depending on the setting of
the speakers.
Set menu
■ Speaker distance C)SP DISTANCE
Use this feature to manually adjust the distance of each
speaker and the delay applied to the respective channel.
Ideally, each speaker should be the same distance from the
main listening position. However, this is not possible in
most home situations. Thus, a certain amount of delay
must be applied to the sound from each speaker so that all
sounds will arrive at the listening position at the same
time.
Unit UNIT
Choices: meters (m), feet (ft)
Initial setting:
[U.S.A. and Canada models]: feet (ft)
[Other models]: meters (m)
• Select “meters” to adjust speaker distances in meters.
• Select “feet” to adjust speaker distances in feet.
Speaker distances
Control range: 0.30 to 24.00 m (1.0 to 80.0 ft)
Control step: 0.10 m (0.5 ft)
Initial setting: 3.00 m (10.0 ft)
SP DISTANCE
Adjusted speaker
Front left speaker
FRONT R
Front right speaker
CENTER
Center speaker
SUR. L
Surround left speaker
SUR. R
Surround right speaker
SWFR
Subwoofer
Following is an example where “100Hz” is selected as the
frequency band.
100Hz--||--
0
Test tone TEST
Use this feature to make adjustments for “CENTER GEQ”
while listening to a test tone.
Choices: OFF, ON
• Select “OFF” to stop test tones and output the currently
selected source component.
• Select “ON” to output test tones from the center and
front left speakers.
■ Low-frequency effect level E)LFE LEVEL
Use this feature to adjust the output level of the LFE (lowfrequency effect) channel according to the capacity of
your subwoofer or headphones. The LFE channel carries
low-frequency special effects which are only added to
certain scenes. This setting is effective only when this unit
decodes Dolby Digital or DTS signals.
Control range: –20 to 0 dB
Control step: 1 dB
ADVANCED
OPERATION
FRONT L
y
Press G k / n to select a frequency band and G l / h to adjust
the selected frequency band.
Speaker LFE SP LFE
Adjusts the speaker LFE level.
Headphone LFE HP LFE
Adjusts the headphone LFE level.
Note
Note
The available speaker channels differ depending on the setting of
the speakers.
Depending on the settings of “BASS OUT” (see page 46), some
signals may not be output at the SUBWOOFER OUTPUT jack.
■ Center graphic equalizer D)CENTER GEQ
■ Dynamic range F)D. RANGE
Use this feature to adjust the built-in 5-frequency band
(100Hz, 300Hz, 1kHz, 3kHz and 10kHz) graphic
equalizer for the center channel so that the tonal quality of
the center speaker matches that of the front speakers. You
can make adjustments while listening to the currently
selected source component or a test tone.
Control range: –6.0 to +6.0 dB
Control step: 0.5 dB
Initial setting: 0 dB
Use this feature to select the amount of dynamic range
compression to be applied to your speakers or
headphones. This setting is effective only when this unit is
decoding Dolby Digital and DTS signals.
Choices: MIN, STD, MAX
• Select “MIN” (minimum) if you regularly listen at low
volume levels.
• Select “STD” (standard) for general use.
Select “MAX” (maximum) to preserve the greatest
amount of dynamic range.
Speaker dynamic range SP D.R
Adjusts the speaker compression.
English
Headphone dynamic range HP D.R
Adjusts the headphone compression.
47 En
Set menu
■ Audio settings G)AUDIO SET
Use this feature to adjust the overall audio settings of this
unit.
Mute type MUTE TYP.
Use this feature to adjust how much the mute function
reduces the output volume (see page 28).
Choices: FULL, –20dB
• Select “FULL” to completely mute all the audio
output.
• Select “–20dB” to reduce the current volume by 20 dB.
Audio delay A.DELAY
Use this feature to delay the sound output and synchronize
it with the video image. This may be necessary when
using certain LCD monitors or projectors.
Control range: 0 to 160 ms
Control step: 1 ms
Maximum volume MAX VOL.
Use this feature to set the maximum volume level in the
main zone. This feature is useful to avoid the unexpected
loud sound by mistake. For example, the original volume
range is 16 dB to –80 dB. However, when “MAX VOL.”
is set to –5 dB, the volume range becomes
–5 dB to –80 dB.
Control range: 16 dB, 10 dB to –30 dB
Control step: 5 dB
Note
The “MAX VOL.” setting takes priority over the “Initial Volume”
setting. For example, if “INI VOL.” is set to –20 dB and “MAX
VOL.” is set to –30 dB, the volume level is automatically set to
–30 dB when you turn on the power of this unit next time.
Initial volume INI VOL.
Use this feature to set the volume level when the power of
this unit is turned on.
Choices: Off, –80 dB to +16 dB
Control step: 1 dB
Note
The “MAX VOL.” setting takes priority over the “INI VOL.”
setting.
48 En
2 INPUT MENU
Use this menu to reassign the input jacks, select the input
mode or rename the input source.
■ Input assignment
A)INPUT ASSIGN
Use this feature to assign the input jacks according to the
component to be used if the initial settings of this unit do
not correspond to your needs. Change the following
parameters to reassign the respective jacks and effectively
connect more components.
Once the input jacks are reassigned, you can select the
corresponding component by using D INPUT l / h (or
the input selector buttons (C) on the remote control).
For COAXIAL INPUT jacks 1
IN (1)
Choices: (1) CD, MD/CD-R, DVD, DTV/CBL, V-AUX,
DVR
For OPTICAL INPUT jacks 2 and 3
IN (2)
IN (3)
Choices: (2) CD, MD/CD-R, DVD, DTV/CBL, V-AUX,
DVR
(3) CD, MD/CD-R, DVD, DTV/CBL, V-AUX,
DVR
Note
You cannot select a specific item more than once.
Set menu
■ Input rename B)INPUT RENAME
Use this feature to change the name of the input source
that appears in the front panel display.
The following is an example where “DVD” is renamed
“My DVD”.
DVR
DVD
1
V-AUX
DTV/CBL pDVD
MD/CD-R
TUNER
CD
XM
My DVD
Press one of the input selector buttons (C)
or A MULTI CH IN to select the input
source you want to change the name of.
MULTI CH IN
2
MD/CD-R
TUNER
DVD
DTV/CBL
DVR
V-AUX
XM
Press D AMP and then press G l / h on the
remote control to place the “_” (underscore)
under the space or the character you want to
edit.
Press G k / n to select the character you
want to use and then press G l / h to move
to the next space.
■ Decoder mode D)DECODER MODE
Decoder select mode
Use this feature to designate the default decoder mode for
the input sources connected to the DIGITAL INPUT jacks
when you turn on the power of this unit.
Choices: AUTO, LAST
• Select “AUTO” if you want this unit to automatically
detect the type of input signals and select the
appropriate decoder mode.
• Select “LAST” if you want this unit to automatically
select the last decoder mode used the connected input
source.
DTS decoder prioritize setting
Choices: AUTO, DTS
• Select “AUTO” if you want this unit to automatically
detect input signal types and select the appropriate
input mode.
• Select “DTS” when you play back a DTS-CD.
■ Multi channel input setup
E)MULTI CH SET
Notes
• You can use up to 8 characters for each input.
• Press G n to change the character in the following order,
or press G k to go in the reverse order:
A to Z, a space, 0 to 9, a space, a to z, a space, symbols (#,
*, –, +, etc.)
ADVANCED
OPERATION
3
CD
■ Volume trim C)VOLUME TRIM
Use this feature to adjust the level of the signal input at
each jack. This is useful if you want to balance the level of
each input source to avoid sudden changes in volume
when switching between input sources.
Choices: CD, MD/CD-R, TUNER, DVD,
DTV/CBL, V-AUX, DVR, MULTI CH IN,
XM RADIO
Control range: –6.0 to +6.0 dB
Control step: 1.0 dB
Initial setting: 0.0 dB
BGV BGV
Use this feature to select the video source played in the
background of the sources input from the MULTI CH
INPUT jacks.
Choices: LAST, DVR, V-AUX, DTV/CBL, DVD
y
4
Repeat steps 1 through 3 to rename each
input source.
5
Press P MENU to exit from “INPUT
RENAME”.
Select “LAST” to set this unit to automatically select the last
selected video source as the background video source.
English
49 En
Set menu
3 OPTION MENU
Use this menu to adjust the optional system parameters.
■ Display settings A)DISPLAY SET
Dimmer DIMMER
Use this feature to adjust the brightness of the front panel
display.
Control range: –4 to 0
Control step: 1
• Press G l to make the front panel display dimmer.
• Press G h to make the front panel display brighter.
Front panel display scroll FL SCROLL
Use this feature to set whether to display the information
(such as song title or channel name) in the front panel
display in a continuous manner or by the first 14
alphanumeric characters after scrolling all characters once
when “XM” is selected as the input source.
Choices: CONT, ONCE
• Select “CONT” to display the operation status in the
front panel display in a continuous manner.
• Select “ONCE” to display the operation status in the
front panel display by the first 14 alphanumeric
characters after scrolling all characters once.
■ Memory guard B)MEMORY GUARD
Memory guard MEM. GUARD
Use this feature to prevent accidental changes to DSP
program parameter values and other system settings.
Choices: OFF, ON
• Select “OFF” to turn off the “MEM. GUARD” feature.
• Select “ON” to protect:
– sound field program parameters
– all set menu items
– all speaker levels
– SCENE template parameters
Note
When “MEM. GUARD” is set to “ON”, you cannot select and
adjust any other set menu items.
50 En
■ Audio select
C)AUDIO SELECT
Use this feature to designate the default audio input jack
select setting for the input sources when you turn on the
power of this unit.
Choices: AUTO, LAST
• Select “AUTO” if you want this unit to automatically
detect the type of input signals and select the
appropriate input mode.
• Select “LAST” if you want this unit to automatically
select the last input mode used for the connected input
source (see page 29).
■ Parameter initialization D)PARAM. INI
Use this feature to set all the parameters of the sound field
programs to the initial factory settings.
Choices: NO, YES
• Select “NO” to cancel the parameter initialization and
return to the previous menu level.
• Select “YES” to set all the sound field parameters to
the initial factory settings.
Notes
• You cannot automatically revert to the previous parameter
settings once you initialize the sound field program parameters.
• You cannot separately initialize individual sound field
programs.
• You cannot initialize any sound field program groups when
“MEM. GUARD” is set to “ON”.
■ XM Radio setting E)XM RADIO SET
(U.S.A. and Canada models only)
XM Radio antenna XM ANT.
Use this feature to check the current reception level of the
XM Satellite Radio signals (see page 37). For the best
reception, orient XM Mini-Tuner Dock so that a value of
60% or more is displayed here.
Display status: NONE, 0 to 100%
Note
“NONE” is displayed if XM Mini-Tuner Dock is not connected to
this unit. In this case, check the antenna connections (see
page 37).
Remote control features
Remote control features
In addition to controlling this unit, the remote control can also operate other audiovisual components made by Yamaha
and other manufacturers. To control your TV or other components, you must set up the appropriate remote control code
for each input source (see page 54).
Using remote control on the SCENE feature
■ Controlling the input source
components in the SCENE mode
■ Setting input source of the customized
SCENE template on the remote control
You can operate both this unit and the input source
component by using the remote control. You must set the
appropriate remote control code for each input source in
advance (see page 54).
If you customize the input source of the selected SCENE
template, you must set the input source of the SCENE
template on the remote control to operate the input source
component correctly.
1
Press the desired E SCENE button on the
remote control.
2
Press the desired buttons in the * area below
to control the input source component of the
selected SCENE template.
Press and hold the E SCENE button and the
desired input selector button (C) for 3 seconds.
y
POWER
STANDBY
POWER
AV
AUDIO SEL
SLEEP
MUTE
CD
MD/CD-R
TUNER
DVR
TV CH
TV MUTE
TV VOL
DVD
DTV/CBL
V-AUX
XM
AMP
TV INPUT
1
2
SCENE
BAND LEVEL
TITLE
3
4
ADVANCED
OPERATION
*
POWER
TV
MULTI CH IN
Press the E SCENE button again to operate the input source
component.
SCENE buttons
SRCH MODE
VOLUME
MENU
ENTER
RETURN
XM MEMORY
DISPLAY
REC
l
PROG h
1
2
ENHANCER STRAIGHT
3
4
SUR.DECODE NIGHT
5
6
7
9
0
10
8
ENT.
Note
*
These buttons control the input source component. See page 53
for details of the function of each button.
English
51 En
Remote control features
Controlling this unit, a TV, or other components
■ Controlling this unit
■ Controlling a TV
Press D AMP to control this unit.
Press C DTV/CBL to control your TV. To control your
TV, you must set the appropriate remote control code for
DTV/CBL (see page 54).
POWER
POWER
STANDBY
POWER
TV
AV
MULTI CH IN
AUDIO SEL
SLEEP
MUTE
CD
MD/CD-R
TUNER
DVD
DTV/CBL
DVR
TV CH
TV MUTE
TV VOL
POWER
V-AUX
XM
AMP
TV INPUT
1
2
*1
DTV/CBL
AMP
POWER
STANDBY
POWER
TV
AV
MULTI CH IN
AUDIO SEL
SLEEP
MUTE
CD
MD/CD-R
TUNER
DVR
TV CH
TV MUTE
TV VOL
DVD
DTV/CBL
V-AUX
XM
AMP
TV INPUT
1
2
*1
SCENE
BAND LEVEL
TITLE
3
4
SCENE
SRCH MODE
VOLUME
MENU
BAND LEVEL
TITLE
3
4
SRCH MODE
VOLUME
MENU
ENTER
ENTER
RETURN
XM MEMORY
*2
DISPLAY
REC
RETURN
XM MEMORY
l
PROG h
1
2
*2
ENHANCER STRAIGHT
3
4
5
6
7
8
9
0
10
DISPLAY
REC
SUR.DECODE NIGHT
l
1
ENT.
PROG h
2
ENHANCER STRAIGHT
3
4
SUR.DECODE NIGHT
5
6
7
9
0
10
8
ENT.
Notes
*1
*2
These buttons always control this unit.
These buttons control this unit only when D AMP is pressed.
Notes
*1
These buttons always control your TV regardless of whether
you press C DTV/CBL or not.
Remote control
*2
52 En
Digital TV/Cable TV
TV POWER
Turns on or off the power.
TV CH +/–
Changes the channel number.
TV VOL +/–
Increases or decreases the volume
level.
TV INPUT
Changes the input source.
TV MUTE
Mutes the audio output.
These buttons control your TV only when C DTV/CBL is
pressed. For details, see the “Digital TV/Cable TV” column on
page 53.
Remote control features
■ Controlling other components
Press one of the input selector buttons (C) or
to
control other components. You must set the appropriate
remote control code for each input source in advance (see
page 54). The following table shows the function of each
control button used to control other components assigned
to each input selector button. Be advised that some buttons
may not correctly operate the selected component.
1
POWER
POWER
TV
AV
MULTI CH IN
AUDIO SEL
SLEEP
MUTE
CD
MD/CD-R
TUNER
DTV/CBL
DVR
V-AUX
XM
AMP
TV INPUT
TV MUTE
TV CH
1
2
3
2
BAND LEVEL
TITLE
3
4
5
SRCH MODE
VOLUME
MENU
7
ENTER
RETURN
XM MEMORY
8
DISPLAY
REC
TV VOL
SCENE
The remote control has 9 modes (input areas) to control
components so that the remote control can operate up to 9
different components.
4
6
l
PROG h
1
2
ENHANCER STRAIGHT
3
4
SUR.DECODE NIGHT
5
6
7
9
0
10
8
ENT.
9
DVD player/
VCR
recorder
Digital TV/
Cable TV
LD player
CD player
MD/CD
recorder
AV POWER
Power *1
Power *2
Power *1
Power *1
Power *1
TITLE
Title
PRESET/CH k
Up
VCR channel up Up
Preset up (1-8)
PRESET/CH n
Down
VCR channel
down
Down
Preset down
(1-8)
A-E/CAT. l
Left
Left
Preset down
(A-E)
A-E/CAT. h
Right
Right
Preset up
(A-E)
Remote control
Power *1
Tuner
Band
ENTER
Enter
Enter
RETURN
Return
Return
REC
Disc skip
(player)
Rec (recorder)
Rec
Rec *2
p
Play
Play
Play *2
w
Search backward
Search backward Search backward
Search backward Search backward Search backward
*2
f
Search forward
Search forward
Search forward
*2
Search forward
Search forward
Search forward
e
Pause
Pause
Pause *2
Pause
Pause
Pause
Skip backward
*2
Skip backward
Skip backward
Skip backward
Play
Disc skip
Rec
Play
Play
b
Skip backward
Skip backward
a
Skip forward
Skip forward
Skip forward *2
Skip forward
Skip forward
Skip forward
s
Stop
Stop
Stop *2
Stop
Stop
Stop
6
1-9, 0, +10
Numeric buttons Numeric buttons Numeric buttons Numeric buttons
7
8
9
MENU
Menu
DISPLAY
Display
Display
Display
Display
Display
Display
ENT.
Title/Index
Enter
Enter
Chapter/Time
Index
Index
Numeric buttons Numeric buttons
ADVANCED
OPERATION
4
5
POWER
DVD
y
1
2
3
STANDBY
Preset stations
(1-8)
Menu
Notes
*1
*2
This button is operational only when the original remote control supplied with the component has a POWER button.
These buttons operate your DVD recorder only when you set the appropriate remote control code for DVR (see page 54).
English
53 En
Remote control features
Setting remote control codes
1
You can control other components by setting the
appropriate remote control codes. For a complete list of
available remote control codes, refer to “List of remote
control codes” at the end of this manual.
While pressing and holding one of the input
selector buttons (C) on the remote control to
select the input area you want to set up,
press AV POWER for more than 3 seconds.
CD
MD/CD-R
TUNER
DVD
DTV/CBL
DVR
Remote control code default settings
Input
source
Component
category
Manufacturer
CD
CD
YAMAHA
5013
MD/CD-R
CD-R
YAMAHA
5001
TUNER
TUNER
YAMAHA
5007
DVD
DVD
YAMAHA
2000
DTV/CBL
–
–
–
V-AUX
TUNER
YAMAHA
5011
XM
TUNER
YAMAHA
5009
DVR
DVR
YAMAHA
2011
TUNER
YAMAHA
5012
Note
You may not be able to operate your Yamaha component even if a
Yamaha remote control code is preset as listed above. In this case,
try setting another Yamaha remote control code.
54 En
POWER
AV
Default
code
V-AUX
XM
While holding down
2
Press for 3 seconds
Press the numeric buttons (0 to 9) (V) to
enter the four-digit remote control code for
the component to be used.
Notes
• If the manufacturer of your component has more than one code,
try each of them until you find the correct one.
• If you do not press any buttons within 30 seconds in step 2, the
setup process is canceled. If this happens, repeat the setup
procedure.
Advanced setup
Advanced setup
This unit has additional menus that are displayed in the
front panel display. The advanced setup menu offers
additional operations to adjust and customize the way this
unit operates. Change the initial settings (indicated in bold
under each parameter) to reflect the needs of your
listening environment.
Notes
• Only 1 STANDBY/ON, A PROGRAM l / h and
B STRAIGHT are effective while you are using the advanced
setup menu.
• No other operations can be made while you are using the
advanced setup menu.
• The advanced setup menu is only available in the front panel
display.
■ Speaker impedance SP IMP.
(U.S.A. and Canada models only)
Use this feature to set the speaker impedance of this unit
so that it matches that of your speakers.
Choices: 8Ω MIN, 6Ω MIN
• Select “8Ω MIN” to set the speaker impedance to 8 Ω .
• Select “6Ω MIN” to set the speaker impedance to 6 Ω .
SP IMP.
Speaker
Impedance level
Front (A or B)
8Ω MIN
Center
The impedance of each
speaker must be 8 Ω or
higher.
Surround
Front (A or B)
1
Press 1 STANDBY/ON on the front panel to
set this unit to the standby mode.
2
Press and hold 0 TONE CONTROL and
then press 1 STANDBY/ON to turn on this
unit.
This unit turns on, and the advanced setup menu
appears in the front panel display.
3
Press A PROGRAM l / h to select the
parameter you want to adjust.
The name of the selected parameter appears in the
front panel display.
6Ω MIN
Center
The impedance of each
speaker must be 6 Ω or
higher.
Surround
Notes
4
Press B STRAIGHT repeatedly to change
the selected parameter setting.
• This setting completely resets all the parameters of this unit
including the set menu parameters. However, the advanced
setup menu parameters will not be initialized.
• The initial factory settings are activated next time you turn on
this unit.
5
Press 1 STANDBY/ON to confirm your
selection and set this unit to the standby
mode.
■ Tuner frequency step TU
(Asia and General models only)
y
The settings you made are reflected next time you turn on this
unit.
ADVANCED
OPERATION
■ Factory presets PRESET
Use this feature to reset all the parameters of this unit to
the initial factory settings.
Choices: CANCEL, RESET
• Select “CANCEL” not to reset any parameters of this
unit.
• Select “RESET” to reset the parameters of this unit.
Use this feature to set the tuner frequency step according
to the frequency spacing in your area.
Choices: AM10/FM100, AM9/FM50
• Select “AM10/FM100” for North, Central and South
America.
• Select “AM9/FM50” for all other areas.
English
55 En
Troubleshooting
Troubleshooting
Refer to the table below when this unit does not function properly. If the problem you are experiencing is not listed below
or if the instruction below does not help, turn off this unit, disconnect the power cable, and contact the nearest authorized
Yamaha dealer or service center.
■ General
Problem
This unit fails to turn
on or enters the
standby mode soon
after the power is
turned on.
No sound
56 En
Cause
Remedy
See
page
The power cable is not connected or the
plug is not completely inserted.
Connect the power cable firmly.
—
The speaker impedance setting is
incorrect.
Set the speaker impedance to match your speakers.
13
The protection circuitry has been
activated.
Make sure that all speaker wire connections on this
unit and on all speakers are secure and that the wire
for each connection does not touch anything other
than its respective connection.
12
This unit has been exposed to a strong
external electric shock (such as lightning
or strong static electricity).
Set this unit to the standby mode, disconnect the
power cable, plug it back in after 30 seconds and then
use it normally.
—
Incorrect input or output cable
connections.
Connect the cables properly. If the problem persists,
the cables may be defective.
14-17
No appropriate Audio input jack select has
been set.
Set an appropriate Audio input jack select.
No appropriate input source has been
selected.
Select an appropriate input source with D INPUT
l / h on the front panel (or the input selector
buttons on the remote control).
Speaker connections are not secure.
Secure the connections.
12
The front speakers to be used have not
been selected properly.
Select the front speakers with 9 SPEAKERS.
27
The volume is turned down.
Turn up the volume.
—
The sound is muted.
Press N MUTE or Q VOLUME +/– on the remote
control to resume audio output and then adjust the
volume.
28
Signals this unit cannot reproduce are
being input from a source component,
such as a CD-ROM.
Play a source whose signals can be reproduced by this
unit.
—
29
27, 28
Troubleshooting
Problem
The sound suddenly
goes off.
Sound is heard from
the speaker on one
side only.
Cause
The protection circuitry has been activated
because of a short circuit, etc.
Remedy
See
page
Check that the impedance setting is correct.
13
Check that the speaker wires are not touching each
other and then turn this unit back on.
—
The sleep timer has turned off this unit.
Turn on this unit, and play the source again.
—
The sound is muted.
Press N MUTE or Q VOLUME +/– on the remote
control to resume audio output.
28
Incorrect cable connections.
Connect the cables properly. If the problem persists,
the cables may be defective.
14-17
Incorrect settings in “SP LEVEL”.
Adjust the “SP LEVEL” settings.
29
When playing a monaural source with a
CINEMA DSP program, the source signal
is directed to the center channel, and the
front and surround speakers output effect
sounds.
No sound is heard
from the center
speaker.
“CENTER” in “SPEAKER SET” is set to
“NONE”.
Set “CENTER” to “SML” or “LRG”.
45
One of the HiFi DSP programs (except for
5ch Stereo) has been selected.
Try another sound field program.
31
“SUR. LR” in “SPEAKER SET” is set to
“NONE”.
Set “SUR. LR” to “SML” or “LRG”.
45
This unit is in the “STRAIGHT” mode
and a monaural source is being played
back.
Press B STRAIGHT on the front panel so that
“STRAIGHT” disappears from the front panel
display.
33
“BASS OUT” in “SPEAKER SET” is set
to “FRNT” when a Dolby Digital or DTS
signal is being played.
Set “BASS OUT” to “SWFR” or “BOTH”.
46
“BASS OUT” in “SPEAKER SET” is set
to “SWFR” or “FRNT” when a 2-channel
source is being played.
Set “BASS OUT” to “BOTH”.
46
No sound is heard
from the surround
speakers.
No sound is heard
from the subwoofer.
ADDITIONAL
INFORMATION
Only the center
speaker outputs
substantial sound.
The source does not contain lowfrequency bass signals.
English
57 En
Troubleshooting
Problem
Cause
Remedy
See
page
Dolby Digital or DTS
sources cannot be
played. (Dolby Digital
or DTS indicator in
the front panel
display does not light
up.)
The connected component is not set to
output Dolby Digital or DTS digital
signals.
Make an appropriate setting following the operating
instructions for your component.
—
Audio input jack select is set to
“ANALOG”.
Set Audio input jack select to “AUTO”.
29
A humming sound is
heard.
Incorrect cable connections.
Connect the audio cables firmly. If the problem
persists, the cables may be defective.
—
The volume level
cannot be increased,
or the sound is
distorted.
You are attempting to set the volume level
higher than the maximum volume level.
Adjust “MAX VOL.” setting.
48
The component connected to the AUDIO
OUT (REC) jacks of this unit is turned
off.
Turn on the power of the component.
—
The sound effect
cannot be recorded.
It is not possible to record the sound effect
with a recording component.
A source cannot be
recorded by an
analog component
connected to the
AUDIO OUT (REC)
jacks.
The source component is not connected to
the analog AUDIO IN jacks of this unit.
Connect the source component to the analog AUDIO
IN jacks.
The sound field
parameters and some
other settings of this
unit cannot be
changed.
“MEM. GUARD” in “OPTION MENU”
is set to “ON”.
Set “MEM. GUARD” to “OFF”.
50
This unit does not
operate properly.
The internal microcomputer has been
frozen by an external electric shock (such
as lightning or excessive static electricity)
or by a power supply with low voltage.
Disconnect the power cable from the AC wall outlet
and then plug it in again after about 30 seconds.
—
“CHECK SP WIRES”
appears in the front
panel display.
Speaker cables are short-circuited.
Make sure all speaker cables are connected correctly.
12
There is noise
interference from
digital or radio
frequency equipment.
This unit is too close to the digital or highfrequency equipment.
Move this unit further away from such equipment.
—
The picture is
disturbed.
The video source uses scrambled or
encoded signals to prevent dubbing.
This unit suddenly
enters the standby
mode.
The internal temperature is too high and
the overheat protection circuitry has been
activated.
Wait about 1 hour for this unit to cool down and then
turn it back on.
—
58 En
15, 17
Troubleshooting
■ Tuner
Problem
Cause
FM stereo reception is
noisy.
FM
AM
■
Remedy
The characteristics of FM stereo
broadcasts may cause this problem
when the transmitter is too far away or
the antenna input is poor.
See
page
Check the antenna connections.
18
Try using a high-quality directional FM
antenna.
—
Use the manual tuning method.
34
There is distortion, and
clear reception cannot
be obtained even with a
good FM antenna.
There is multi-path interference.
Adjust the antenna position to eliminate
multi-path interference.
—
The desired station
cannot be tuned into
with the automatic
tuning method.
The signal is too weak.
Use a high-quality directional FM antenna.
—
Use the manual tuning method.
34
Previously preset
stations can no longer
be tuned into.
This unit has been disconnected for a
long period.
Set preset stations.
35
The desired station
cannot be tuned into
with the automatic
tuning method.
The signal is weak or the antenna
connections are loose.
Tighten the AM loop antenna connections
and orient it for the best reception.
—
Use the manual tuning method.
34
There are continuous
crackling and hissing
noises.
Noises result from lightning,
fluorescent lamps, motors, thermostats
and other electrical equipment.
Use an outdoor antenna and a ground wire.
This will help somewhat, but it is difficult to
eliminate all noise.
—
There are buzzing and
whining noises.
A TV set is being used nearby.
Move this unit away from the TV set.
—
XM Satellite Radio (U.S.A. and Canada models only)
Status message
Cause
Remedy
See
page
The XM Mini-Tuner and XM Dock are
not connected to the XM jack of this unit
or do not work properly.
Check XM Mini-Tuner and XM Dock connections
and orient for the best reception level.
37
UPDATING
The XM user encryption code is being
updated.
Wait until the encryption code is updated.
—
NO SIGNAL
The signal is too weak.
Adjust the orientation of the XM Mini-Tuner for the
best reception level.
37
LOADING
It takes longer than four seconds for audio
or text data to be decoded.
Wait until the decoding process has finished.
—
OFF AIR
The XM Satellite Radio channel you
selected is not currently broadcasting any
signals.
Check the channel number again or select another
XM Satellite Radio channel.
—
<XM> - - -
The Channel Station ID (SID) is no longer
available.
- - -
No artist name or song title is available.
Select another channel category by pressing
4 CATEGORY (or G A-E/CAT. l / h) repeatedly.
39
/
- - -
<CAT> - - -
No channels are available for the selected
category.
59 En
English
CHECK ANTENNA
ADDITIONAL
INFORMATION
If an operation takes longer than usual or an error occurs, one of the following messages may appear in the front panel
display. In this case, read the cause and follow the corresponding remedies.
Troubleshooting
■ Remote control
Problem
The remote control
does not work nor
function properly.
Cause
Remedy
See
page
Wrong distance or angle.
The remote control functions within a maximum
range of 6 m (20 ft) and no more than 30 degrees offaxis from the front panel.
20
Direct sunlight or lighting (from an
inverter type of fluorescent lamp, etc.) is
striking the remote control sensor of this
unit.
Reposition this unit.
—
The batteries are weak.
Replace all batteries.
3
The remote control code is not correctly
set.
Set the remote control code correctly using “List of
remote control codes” at the end of this manual.
54
Try setting another code for the same manufacturer
using “List of remote control codes” at the end of this
manual.
54
Even if the remote control code is
correctly set, there are some models that
do not respond to the remote control.
■ Resetting the system
Use this feature to reset all the parameters of this unit to
the initial factory settings.
1
Press 1 STANDBY/ON on the front panel to
set this unit to the standby mode.
2
Press and hold 0 TONE CONTROL and
then press 1 STANDBY/ON to turn on this
unit.
The advanced setup menu appears in the front panel
display.
3
Press A PROGRAM l / h to select
“PRESET”.
4
Press B STRAIGHT repeatedly to select
“RESET”.
Select “CANCEL” to cancel the initialization
procedure without making any changes.
5
Press 1 STANDBY/ON to confirm your
selection and set this unit to the standby
mode.
60 En
Notes
• This procedure completely resets all the parameters of this unit
including the set menu parameters. However, the advanced
setup menu parameters will not be initialized.
• The initial factory settings are activated next time you turn on
this unit.
y
To cancel the initialization procedure at any time without making
any changes, press B STRAIGHT repeatedly to select
“CANCEL” and then press 1 STANDBY/ON.
Glossary
Glossary
■ Audio information
Dolby Digital
Dolby Digital is a digital surround sound system that gives
you completely independent multi-channel audio. With 3
front channels (front L/R and center), and 2 surround
stereo channels, Dolby Digital provides 5 full-range audio
channels. With an additional channel especially for bass
effects, called LFE (Low Frequency Effect), the system
has a total of 5.1-channels (LFE is counted as 0.1
channel). By using 2-channel stereo for the surround
speakers, more accurate moving sound effects and
surround sound environment are possible than with Dolby
Surround. The wide dynamic range from maximum to
minimum volume reproduced by the 5 full-range channels
and the precise sound orientation generated using digital
sound processing provide listeners with unprecedented
excitement and realism. With this unit, any sound
environment from monaural up to a 5.1-channel
configuration can be freely selected for your enjoyment.
Dolby Pro Logic II
Dolby Pro Logic II is an improved technique used to
decode vast numbers of existing Dolby Surround sources.
This new technology enables a discrete 5-channel
playback with 2 front left and right channels, 1 center
channel, and 2 surround left and right channels instead of
only 1 surround channel for conventional Pro Logic
technology. There are three modes available: “Music
mode” for music sources, “Movie mode” for movie
sources and “Game mode” for game sources.
LFE 0.1 channel
This channel reproduces low-frequency bass signals. The
frequency range of this channel is from 20 Hz to 120 Hz.
This channel is counted as 0.1 because it only enforces a
low-frequency range compared to the full-range
reproduced by the other 5 channels in Dolby Digital or
DTS 5.1-channel systems.
Neural Surround
Neural Surround™ represents the latest advancement in
surround technology and has been adopted by XM
Satellite Radio for digital radio broadcast of surround
recordings and live events in surround sound. Neural
Surround™ employs psychoacoustic frequency domain
processing which allows delivery of a more detailed sound
stage with superior channel separation and localization of
audio elements.
PCM (Linear PCM)
Linear PCM is a signal format under which an analog
audio signal is digitized, recorded and transmitted without
using any compression. This is used as a method of
recording CDs and DVD audio. The PCM system uses a
technique for sampling the size of the analog signal per
very small unit of time. Standing for “Pulse Code
Modulation”, the analog signal is encoded as pulses and
then modulated for recording.
ADDITIONAL
INFORMATION
Dolby Surround
Dolby Surround uses a 4-channel analog recording system
to reproduce realistic and dynamic sound effects: 2 front
left and right channels (stereo), a center channel for dialog
(monaural), and a surround channel for special sound
effects (monaural). The surround channel reproduces
sound within a narrow frequency range. Dolby Surround is
widely used with nearly all video tapes and laser discs,
and in many TV and cable broadcasts as well. The Dolby
Pro Logic decoder built into this unit employs a digital
signal processing system that automatically stabilizes the
volume on each channel to enhance moving sound effects
and directionality.
DTS (Digital Theater Systems)
Digital Surround
DTS digital surround was developed to replace the analog
soundtracks of movies with a 5.1-channel digital sound
track, and is now rapidly gaining popularity in movie
theaters around the world. Digital Theater Systems Inc.
has developed a home theater system so that you can enjoy
the depth of sound and natural spatial representation of
DTS digital surround in your home. This system produces
practically distortion-free 5.1-channel sound (technically,
left, right and center channels, 2 surround channels, plus
an LFE 0.1 channel as a subwoofer, for a total of 5.1channels).
English
61 En
Glossary
Sampling frequency and number of quantized
bits
When digitizing an analog audio signal, the number of
times the signal is sampled per second is called the
sampling frequency, while the degree of fineness when
converting the sound level into a numeric value is called
the number of quantized bits. The range of rates that can
be played back is determined based on the sampling rate,
while the dynamic range representing the sound level
difference is determined by the number of quantized bits.
In principle, the higher the sampling frequency, the wider
the range of frequencies that can be played back, and the
higher the number of quantized bits, the more finely the
sound level can be reproduced.
■ Sound field program information
CINEMA DSP
Since the Dolby Surround and DTS systems were
originally designed for use in movie theaters, their effect
is best felt in a theater having many speakers designed for
acoustic effects. Since home conditions, such as room
size, wall material, number of speakers, and so on, can
differ so widely, it is inevitable that there are differences in
the sound heard. Based on a wealth of actually measured
data, Yamaha CINEMA DSP uses Yamaha original DSP
technology to combine Dolby Pro Logic, Dolby Digital
and DTS systems to provide the audiovisual experience of
movie theater in the listening room of your own home.
SILENT CINEMA
Yamaha has developed a natural, realistic sound effect
DSP algorithm for headphones. Parameters for
headphones have been set for each sound field program so
that accurate representations of all the sound field
programs can be enjoyed on headphones.
Virtual CINEMA DSP
Yamaha has developed a Virtual CINEMA DSP algorithm
that allows you to enjoy DSP surround effects even
without any surround speakers by using virtual surround
speakers. It is even possible to enjoy Virtual CINEMA
DSP using a minimal two-speaker system that does not
include a center speaker.
62 En
■ Video information
Component video signal
With the component video signal system, the video signal
is separated into the Y signal for the luminance and the PB
and PR signals for the chrominance. Color can be
reproduced more faithfully with this system because each
of these signals is independent. The component signal is
also called the “color difference signal” because the
luminance signal is subtracted from the color signal. A
monitor with component input jacks is required in order to
output component signals.
Composite video signal
With the composite video signal system, the video signal
is composed of three basic elements of a video picture:
color, brightness and synchronization data. A composite
video jack on a video component transmits these three
elements combined.
Specifications
Specifications
AUDIO SECTION
• Minimum RMS Output Power for Front, Center, Surround
[U.S.A. and Canada models]
1 kHz, 0.9% THD, 8 Ω .................................................... 100 W
[Other models]
1 kHz, 0.9% THD, 6 Ω .................................................... 100 W
VIDEO SECTION
• Signal Level
Composite ................................................................. 1 Vp-p/75 Ω
Component ......................................................... 1 Vp-p/75 Ω (Y)
• Video Maximum Input Level ................................. 1.5 Vp-p or more
• Maximum Power (JEITA)
[U.S.A. and Canada models]
1 kHz, 10% THD, 8 Ω ..................................................... 135 W
[Asia, China, Korea and General models]
1 kHz, 10% THD, 6 Ω ......................................................135 W
• Signal to Noise Ratio ................................................ 50 dB or more
• MAX Power Per Channel
[U.K. and Europe models]
1 kHz, 0.7% THD, 4 Ω ...................................... 105 W or more
• Tuning Range
[U.S.A. and Canada models] ........................... 87.5 to 107.9 MHz
[Asia and General models]..........87.5/87.50 to 108.0/108.00 MHz
[Other models] ............................................ 87.50 to 108.00 MHz
• IEC Power
[U.K. and Europe models]
1 kHz, 0.1% THD, 8 Ω ........................................ 90 W or more
• Frequency Response (MONITOR OUT)
Component Signal .................................... 5 Hz to 60 MHz, –3 dB
FM SECTION
• 50 dB Quieting Sensitivity (IHF, 100% mod.)
Mono ................................................................. 2.8 µV (20.2 dBf)
• Dynamic Power
[U.S.A. and Canada models] (Impedance Selector: 8 Ω)
(IHF, 8/6/4/2 Ω) .......................................... 110/130/175/185 W
[Other models]
(IHF, 6/4/2 Ω) .................................................... 105/135/165 W
• Signal to Noise Ratio (IHF)
Mono/Stereo .............................................................. 73 dB/70 dB
• Dynamic Headroom
8 Ω .................................................................................... 0.41 dB
AM SECTION
• Frequency Response
CD, etc. to Front L/R ......................... 10 Hz to 100 kHz, 0/–3 dB
V-AUX to Front L/R ............................ 10 Hz to 20 kHz, 0/–3 dB
• Total Harmonic Distortion
CD, etc. (2ch stereo) to Front SP OUT,
50 W/8 Ω .............................................................. 0.06% or less
• Signal to Noise Ratio (IHF-A Network)
CD, etc. (STEREO) Input shorted (250 mV) ........ 100 dB or more
• Channel Separation
CD, etc. Input 5.1 kΩ shorted (1 kHz/10 kHz)
................................................................... 60 dB/45 dB or more
• Tone Control (Front L/R)
BASS Boost/Cut ................................................... ±10 dB/100 Hz
TREBLE Boost/Cut .............................................. ±10 dB/20 kHz
• Headphone Jack Rated Output/Impedance
1 kHz, 50 mV/8 Ω .................................................. 150 mV/100 Ω
• Input Sensitivity/Input Impedance
CD, etc. ................................................................. 200 mV/47 kΩ
MULTI CH INPUT ............................................... 200 mV/47 kΩ
• Maximum Input Signal
CD, etc. 1 kHz, 0.5%THD (EFFECT ON) ............. 2.0 V or more
• Output Level/Output Impedance
AUDIO OUT (REC) ............................................ 200 mV/1.2 kΩ
SUBWOOFER OUTPUT
(2ch Stereo and FRONT SP: SMALL) ..................... 4 V/1.2 kΩ
• Tuning Range
[U.S.A. and Canada models] .............................. 530 to 1710 kHz
[Asia and General models] ................. 530/531 to 1710/1611 kHz
[Other models] ................................................... 531 to 1611 kHz
GENERAL
• Power Supply
[U.S.A. and Canada models] ............................. 120 V AC, 60 Hz
[Australia model] .............................................. 240 V AC, 50 Hz
[Korea model] ................................................... 220 V AC, 60 Hz
[China model] .................................................... 220 V AC, 50 Hz
[U.K. and Europe models] .................................. 230 V AC, 50 Hz
[Asia and General models]
.............................................. 110-120/220–240 V AC, 50/60 Hz
• Power Consumption
[U.S.A. and Canada models] ................................. 240 W/320 VA
[Other models] ................................................................... 240 W
• Standby Power Consumption
[Except Asia and General models] ...................................... 0.8 W
ADDITIONAL
INFORMATION
• Residual Noise (IHF-A Network)
Front L/R ............................................................... 150 µV or less
• Harmonic Distortion (1 kHz)
Mono/Stereo ................................................................ 0.5%/0.5%
• Maximum Power Consumption
[Asia and General models]
5ch, 10%/THD ................................................................ 530 W
• Dimensions (W x H x D) ................................. 435 x 151 x 318 mm
(17-1/8” x 5-15/16” x 12-1/2”)
• Weight ............................................................. 8.0 kg (17 lbs 10 oz)
* Specifications are subject to change without notice.
• Filter Characteristics (fc=40/60/80/90/100/110/120/160/200 Hz)
H.P.F. (Front, Center, Surround) ................................... 12 dB/oct.
L.P.F. (Subwoofer) ........................................................ 24 dB/oct.
English
63 En
INDEX
Index
■
Numerics
1 SOUND MENU ................................ 43
2 INPUT MENU ............................ 43, 48
2ch Stereo ............................................ 31
3 OPTION MENU ......................... 44, 50
5ch Stereo ............................................ 31
■
A
A)DISPLAY SET ................................ 50
A)INPUT ASSIGN .............................. 48
A)SPEAKER SET ............................... 45
A.DELAY ............................................ 48
Activating XM Satellite Radio ............ 38
Adjusting speaker levels
during playback ............................... 29
Adjusting the tonal quality ................... 29
All Channel Search mode .................... 39
AM tuning ............................................ 34
ANTENNA terminals .......................... 10
Audio cable plugs ................................ 14
Audio delay .......................................... 48
AUDIO jacks ................................. 10, 14
Audio jacks .......................................... 14
AUDIO SELECT ........................... 29, 50
Audio select ......................................... 50
Audio settings ...................................... 48
Automatic preset tuning ....................... 35
Automatic tuning ................................. 34
■
B
B)INPUT RENAME ............................ 49
B)MEMORY GUARD ........................ 50
B)SP LEVEL ....................................... 46
BASIC SETUP .............................. 21, 43
Basic setup ........................................... 43
BASS OUT .......................................... 46
■
C
C)SP DISTANCE ................................ 47
C)VOLUME TRIM ............................. 49
Category Search mode ......................... 39
CD Music Listening ............................. 25
CD Listening ........................................ 25
CENTER .............................................. 45
Center graphic equalizer ...................... 47
Center speaker ...................................... 45
Center width ......................................... 32
CINEMA DSP indicator ...................... 19
COAXIAL INPUT assignment ............ 48
COMPONENT VIDEO jacks ........ 10, 14
Connecting a cable TV/satellite tuner .. 15
Connecting a CD player ....................... 17
Connecting a DVD player .................... 15
Connecting a DVD recorder ................ 15
Connecting a video monitor ................. 15
Connecting audio components ............. 17
Connecting speakers ............................ 12
Connecting the AM antennas ............... 18
Connecting the FM antennas ............... 18
Connecting the power cable ................. 18
64 En
Connecting the
XM Mini-Tuner Dock ......................37
Connecting to the
CENTER terminals ..........................13
Connecting to the
COMPONENT VIDEO jacks ..........16
Connecting to the
FRONT A terminals .........................13
Connecting to the
FRONT B terminals .........................13
Connecting to the
MULTI CH INPUT jacks ................17
Connecting to the
SURROUND terminals ....................13
Connecting to the VIDEO AUX ..........16
Connecting video components .............15
Controlling a TV ..................................52
Controlling other components ..............53
Creating original SCENE templates ....26
CROSSOVER ......................................46
Crossover .............................................46
CT WIDTH ..........................................32
■
D
D)CENTER GEQ .................................47
D)DECODER MODE ..........................49
D)PARAM. INI ....................................50
Decoder mode ......................................49
Decoder select mode ............................49
DIGITAL AUDIO COAXIAL jacks ...14
DIGITAL AUDIO OPTICAL jacks ....14
DIGITAL INPUT jacks .......................10
DIMENSION .......................................32
Dimension ............................................32
DIMMER .............................................50
Dimmer ................................................50
Direct Number Access mode ...............39
Disc Listening ......................................25
Display settings ....................................50
Displaying the XM Satellite Radio
information .......................................41
DSP LEVEL .........................................32
DSP level ..............................................32
DTS decoder indicator .........................19
DTS decoder prioritize setting .............49
DVD Live Viewing ..............................25
DVD Movie Viewing ...........................25
DVD Viewing ......................................25
DVR Viewing ......................................25
Dynamic range .....................................47
■
E
E)LFE LEVEL .....................................47
E)MULTI CH SET ...............................49
Editing sound fields parameters ...........32
ENHANCER indicator .........................19
Enjoying 2-channel sources using the
standard decoders .............................32
Exchanging preset stations ...................36
■
F
F)D. RANGE ....................................... 47
Factory presets ..................................... 55
FL SCROLL ........................................ 50
FM tuning ............................................ 34
FRONT ................................................ 45
FRONT B ............................................ 45
FRONT B speaker setting ................... 45
Front panel display .............................. 19
Front panel display scroll .................... 50
Front speakers ...................................... 45
■
G
G)AUDIO SET .................................... 48
Game ................................................... 31
Game Playing ...................................... 25
■
H
Hall ...................................................... 31
Headphone ........................................... 47
Headphone dynamic range .................. 47
Headphones indicator .......................... 19
HiFi DSP indicator .............................. 19
HP D.R ................................................ 47
HP LFE ................................................ 47
■
I
Infrared window .................................. 20
INI VOL. ............................................. 48
Initial volume ...................................... 48
Input assignment .................................. 48
Input channel and speaker indicators .. 19
Input channel indicators ...................... 19
Input menu ........................................... 43
Input rename ........................................ 49
Input source indicators ........................ 19
Input source information ..................... 30
Installing batteries
in the remote control ......................... 3
■
J
Jazz ...................................................... 31
■
L
LFE indicator ....................................... 19
LFE/Bass out ....................................... 46
Listening to unprocessed
input signals .................................... 33
Low-frequency effect level ................. 47
■
M
Manual preset tuning ........................... 35
MANUAL SETUP .............................. 43
Manual setup ....................................... 43
Manual tuning ...................................... 34
MAX VOL. ......................................... 48
Maximum volume ............................... 48
MEM. GUARD ................................... 50
Memory guard ..................................... 50
Movie Dramatic ................................... 31
Movie Spacious ................................... 31
Index
MULTI CH INPUT jacks .................... 10
Multi channel input setup .................... 49
Multi-channel sources and sound field
programs with headphones .............. 33
Multi-information display .................... 19
Music Disc Listening ........................... 25
Music Enh. 2ch .................................... 31
Music Enh. 5ch .................................... 31
MUTE indicator ................................... 19
MUTE TYP. ......................................... 48
Muting type .......................................... 48
■
N
NIGHT indicator .................................. 19
Night listening mode ............................ 28
■
O
OPTICAL INPUT assignment ............. 48
Option menu ........................................ 44
SP LFE .................................................47
Speaker .................................................47
Speaker distance ...................................47
Speaker distances .................................47
Speaker dynamic range ........................47
Speaker impedance ...............................55
Speaker level ........................................46
Speaker settings ....................................45
SPEAKERS terminals ..........................10
Specifications .......................................63
Straight mode .......................................33
SUBWOOFER OUTPUT jack .............10
Subwoofer phase ..................................46
Supplied accessories ...............................3
SUR. LR ...............................................45
Surround left/right speakers .................45
SWFR PHASE .....................................46
■
T
Parameter initialization ........................ 50
PCM indicator ...................................... 19
Placing speakers ................................... 11
Playing video sources
in the background ............................ 30
Pop/Rock .............................................. 31
PRESET ............................................... 55
Preset SCENE templates ...................... 25
Preset Search mode .............................. 39
TEST ....................................................47
Test tone ...............................................47
Troubleshooting ...................................56
TU ........................................................55
Tuner frequency step ............................55
Tuner indicators ...................................19
Turning off the power ..........................18
Turning on the power ...........................18
TV Sports .............................................31
TV Sports Viewing ..............................25
TV Viewing ..........................................25
■
■
■
P
R
U
Radio Listening .................................... 25
Rear panel ............................................ 10
Remote control codes ............................iii
Resetting the system ............................ 60
UNIT ....................................................47
Unit .......................................................47
Using the remote control ......................20
Using your headphones ........................28
■
■
S
V
Video cable plugs .................................14
VIDEO jacks ..................................10, 14
Video jacks ...........................................14
VIRTUAL indicator .............................19
VOLTAGE SELECTOR ........................3
VOLUME level indicator .....................19
Volume Trim ........................................49
■
ADDITIONAL
INFORMATION
X
XM jack ................................................10
XM Listening .......................................25
XM Satellite Radio tuning ...................37
English
SCENE 1 ................................................ 8
SCENE 2 ................................................ 8
SCENE 3 ................................................ 8
SCENE 4 ................................................ 8
Selecting audio input jacks .................. 29
Selecting preset stations ....................... 36
Selecting the MULTI CH INPUT
component as the input source ......... 28
Selecting the night listening mode ....... 28
Selecting the SCENE templates ........... 23
Set menu .............................................. 43
Set this unit to the standby mode ......... 18
Setting input source of the customized
SCENE template
on the remote control ....................... 51
Setting remote control codes ................ 54
Setting the speaker impedance ............. 13
Setting XM Satellite Radio preset ....... 40
SILENT CINEMA ............................... 33
SILENT CINEMA indicator ................ 19
SLEEP indicator .................................. 19
Sleep timer ........................................... 30
Sound field programs ........................... 31
Sound menu ......................................... 43
SP A B indicators ................................. 19
SP D.R ................................................. 47
SP IMP. ................................................ 55
65 En
■ Front panel
1
2
3
4
5
6
7
8
VOLUME
STANDBY
/ON
EDIT
SEARCH MODE
PRESET/TUNING
CATEGORY
A/B/C/D/E
FM/AM
l
PRESET/TUNING/CH
h
MEMORY
DISPLAY
TUNING AUTO/MAN'L
SCENE
1
l
PHONES
SPEAKERS
A/B/OFF
PROGRAM
TONE CONTROL
3
4
l
STRAIGHT
INPUT
NIGHT
VIDEO AUX
h
AUDIO SELECT
EFFECT
SILENT CINEMA
9
i
2
h
0
A
B C
D
E F
VIDEO
L
AUDIO
R
PORTABLE
■ Remote control
X
A
B
C
POWER
POWER
TV
AV
MULTI CH IN
STANDBY
POWER
AUDIO SEL
SLEEP
MUTE
CD
MD/CD-R
TUNER
DVD
DTV/CBL
DVR
TV CH
V-AUX
XM
AMP
TV INPUT
TV MUTE
TV VOL
1
2
L
M
N
O
D
E
F
SCENE
BAND LEVEL
TITLE
G
H
3
4
SRCH MODE
VOLUME
MENU
Q
ENTER
RETURN
XM MEMORY
P
R
DISPLAY
REC
I
J
K
l
PROG h
1
2
ENHANCER STRAIGHT
3
4
SUR.DECODE NIGHT
5
6
7
9
0
10
8
ENT.
S
T
U
V
W
APPENDIX
ii
List of remote control codes
TV
ACER
ACME
ACURA
ADA
ADC
ADMIRAL
ADYSON
AGASHI
AGAZI
AGB
AIKO
AIWA
AKAI
AKIBA
AKURA
ALARON
ALBA
ALBIRAL
ALLSTAR
AMPLIVISION
0093
0207
0208
0255
0206
0058, 0205, 0206,
0210, 0211
0200, 0207
0200
0206
0204
0127, 0200, 0207,
0208
0028, 0139, 0229,
0237
0059, 0065, 0127,
0129, 0130, 0200,
0204, 0208, 0209,
0213, 0217, 0218,
0255
0209, 0218
0206, 0209, 0218
0200
0200, 0207, 0208,
0209, 0217, 0218
0212
0213
0207
0204, 0206, 0208,
0209, 0218
AMTRON
0062
ANAM
0208
ANAM NATIONAL
0062
ANGLO
0208
ANITECH
0206, 0208
ANSONIC
0203, 0208
AOC
0060, 0061
APEX
0118, 0122, 0132
ARC EN CIEL 0216
ARCAM
0200
ARCAM DELTA
0207
ARISTONA
0213, 0217
ASA
0205, 0211
ASBERG
0213
ASTRA
0208
ASUKA
0200, 0206, 0207,
0209, 0218
ATLANTIC
0200, 0207, 0213,
0217
ATORI
0208
AUDIOSONIC 0207, 0208, 0209,
0213, 0216, 0217,
0218
AUDIOTON
0207
AUDIOVOX
0062
AUTOVOX
0205, 0206, 0207
AWA
0200
BAIRD
0216
BANG & OLUFSEN
0205
BASIC LINE 0208, 0209, 0213,
0218
BASTIDE
0207
BAUR
0217
BEKO
0228
BELCOR
0060
AMSTRAD
iii
BELL & HOWELL
0058, 0064
BENQ
0051, 0081
BEON
0213, 0217
BESTAR
0213
BINATONE
0207
BLACK STAR 0214
BLAUPUNKT 0255
BLUE SKY
0209, 0218
BONDSTEC 0214
BOOTS
0207
BRADFORD 0062
BRANDT
0216, 0226
BRIONVEGA 0205, 0213, 0217
BRITANNIA 0200, 0207
BROCKWOOD
0060
BROKSONIC 0138
BRUNS
0205
BSR
0215
BTC
0209, 0218
BUSH
0177, 0208, 0209,
0210, 0213, 0215,
0216, 0217, 0218,
0230, 0237
CANDLE
0060, 0061
CAPSONIC
0206
CASCADE
0208
CATHAY
0213, 0217
CCE
0127
CELEBRITY 0059
CENTURION 0213, 0217
CENTURY
0205
CGE
0214, 0215
CIMLINE
0208, 0218
CITIZEN
0060, 0061, 0062,
0064
CITY
0208
CLARIVOX
0212, 0217
CLATRONIC 0206, 0207, 0208,
0209, 0213, 0214,
0218
CMS
0200
COLORTYME 0060, 0061
CONCERTO 0060, 0061
CONCORDE 0208
CONDOR
0200, 0207, 0213
CONTEC
0200, 0207, 0208
CONTEC/CONY
0062
CONTINENTAL EDISON
0216
COSMEL
0208
CRAIG
0062
CROSLEY
0205, 0214, 0215
CROWN
0062, 0063, 0128,
0208, 0213, 0217
CS ELECTRONICS
0200, 0207, 0209,
0214, 0218
CTC
0214
CURTIS MATHES
0057, 0060, 0061,
0064, 0065
CXC
0062
CYBERTRON 0209, 0218
DAEWOO
0060, 0061, 0120,
0127, 0155, 0193,
0200, 0207, 0208,
0213, 0218, 0238
DAINICHI
DANSAI
DANTAX
DAYTRON
DE GRAAF
DECCA
DESMET
DIAMOND
DIMENSIA
DIXI
DTS
DUAL
DUAL-TEC
DUMONT
0200, 0209, 0218
0200, 0206, 0213,
0217
0217
0060, 0061, 0208
0210
0204, 0207, 0213,
0217
0213, 0217
0200
0057
0208, 0213, 0217
0208
0207, 0215, 0216
0207, 0208, 0215
0060, 0127, 0205,
0207
DURABRAND
0126
0217
0213, 0217
0203, 0204, 0212,
0218
ELBE-SHARP 0204
ELCIT
0204, 0205
ELECTRO TECH
0208
ELECTROBAND
0059
ELECTROHOME
0059, 0060, 0061
ELIN
0200, 0207, 0213,
0217
ELITE
0209, 0213, 0218
ELMAN
0215
ELTA
0200, 0208
EMERSON
0060, 0061, 0062,
0064, 0128, 0205
ENVISION
0060, 0061
ERRES
0213, 0217
ESA
0080
ETRON
0208
EURO-FEEL 0206
EUROLINE
0217
EUROMAN
0200
EUROMANN 0206, 0207, 0213
EUROPHON 0200, 0204, 0207,
0213, 0215
FENNER
0208
FERGUSON 0212, 0217, 0226
FIDELITY
0200, 0207, 0210
FINLANDIA 0210
FINLUX
0204, 0205, 0207,
0213, 0215, 0217
FIRSTLINE
0200, 0207, 0208,
0213, 0214
FISHER
0064, 0127, 0128,
0205, 0207, 0215
FLINT
0213, 0218
FORMENTI
0200, 0205, 0207,
0215, 0217
FORMENTI-PHOENIX
0200
FORTRESS
0205
FRONTECH
0206, 0208, 0210,
0211, 0214
FUJITSU
0023, 0024, 0025,
0088, 0127
FUNAI
0033, 0034, 0035,
0036, 0037, 0062,
0206
DUX
DYNATRON
ELBE
FUTURETECH
0062
0094
0208, 0215, 0218
0057, 0060, 0061,
0122, 0147
GEC
0204, 0207, 0211,
0213, 0217
GELOSO
0208, 0210, 0215
GENERAL TECHNIC
0208
GENEXXA
0209, 0211, 0213,
0218
GIBRALTER 0060
GOLDHAND 0200
GOLDSTAR 0060, 0061, 0127,
0128, 0200, 0201,
0207, 0208, 0210,
0213, 0214, 0215,
0217
GOODMANS 0171, 0201, 0204,
0206, 0208, 0213,
0217, 0240
GPM
0209, 0218
GRAETZ
0211
GRANADA
0204, 0207, 0210,
0213, 0217
GRANDIN
0208, 0209, 0217
GRUNDIG
0128, 0130, 0222,
0236, 0255
GRUNPY
0062
HALIFAX
0200, 0206, 0207
HALLMARK 0060, 0061
HAMPTON
0200, 0207
HANSEATIC 0203, 0207, 0208,
0213, 0215, 0217
HANTAREX 0204, 0208
HARVARD
0062
HCM
0206, 0207, 0208,
0218
HIFIVOX
0216
HIGASHI
0200
HINARI
0208, 0209, 0213,
0217, 0218
HISAWA
0209, 0218
HITACHI
0006, 0014, 0015,
0016, 0042, 0060,
0061, 0095, 0105,
0127, 0156, 0179,
0180, 0204, 0207,
0210, 0211, 0215,
0216, 0251
HORNYPHON 0213
HOSHAI
0209, 0218
HUANYU
0200, 0207
HYGASHI
0200, 0207
HYPER
0200, 0207, 0208,
0214, 0215
HYPSON
0206, 0207, 0213,
0217
ICE
0127, 0200, 0206,
0207, 0208, 0209,
0213, 0218
ICES
0200, 0218
IMA
0062
IMPERIAL
0211, 0213, 0214,
0215
INDIANA
0213, 0217
INFINITY
0063
INGELEN
0211
INGERSOL
0208
GATEWAY
GBC
GE
INNO HIT
MAGNADYNE
0204, 0205, 0214,
0215, 0217
MAGNAFON 0200, 0204, 0207
MAGNAVOX 0060, 0061, 0063,
0102, 0103, 0150
MAGNUM
0206, 0208
MAJESTIC
0058
MANDOR
0206
MANESTH
0206, 0207, 0213,
0217
MARANTZ
0060, 0061, 0063,
0090, 0213, 0217
MARELLI
0205
MARK
0200, 0213, 0217
MATSUI
0204, 0207, 0208,
0210, 0213, 0217
MEDIATOR
0213, 0217
MEDION
0206, 0208
MEGATRON 0061
MELECTRONIC
0200, 0207, 0208,
0211, 0213, 0216,
0217
MEMOREX
0058, 0061, 0064,
0208
MEMPHIS
0208
METZ
0205
MGA
0060, 0061
MICROMAXX 0206, 0208
MICROSTAR 0206, 0208
MINERVA
0204
MINOKA
0213
MITSUBISHI 0006, 0015, 0016,
0048, 0060, 0061,
0104, 0112, 0113,
0125, 0205, 0213
MIVAR
0200, 0201, 0202,
0203, 0204, 0207
MONTGOMERY WARD
0058
MTC
0060, 0061, 0128,
0200
MULTI SYSTEM
0217
MULTITECH 0062, 0127, 0128,
0200, 0207, 0208,
0210, 0214, 0215,
0217
MURPHY
0200, 0207
NAD
0061
NAONIS
0210
NEC
0026, 0053, 0060,
0061, 0096, 0127
NECKERMANN
0205, 0207, 0210,
0213, 0217, 0255
NEI
0213, 0217
NESCO
0214
NET-TV
0082, 0101
NEW TECH
0208, 0213
NEW WORLD 0209, 0218
NICAMAGIC 0200, 0207
NIKKAI
0200, 0206, 0207,
0209, 0213, 0217,
0218
NIKKO
0061
NOBLIKO
0200, 0207
NOGAMATIC 0216
NOKIA
0129, 0211
NORDMENDE
0205, 0211, 0213,
0216
NORDVISION 0217
OCEANIC
0211
OLEVIA
ONCEAS
ONWA
ORBIT
ORION
0052, 0084
0207
0062, 0218
0213
0126, 0204, 0208,
0213, 0217, 0235
ORLINE
0218
ORSOWE
0204
OSAKI
0127, 0206, 0207,
0209, 0218
OSIO
0201
OSO
0209, 0218
OSUME
0218
OTTO VERSAND
0204, 0207, 0213,
0215, 0216, 0217,
0255
PAEL
0200, 0207
PALLADIUM 0207
PANAMA
0200, 0206, 0207,
0208
PANASONIC 0006, 0007, 0063,
0073, 0074, 0097,
0110, 0114, 0137,
0141, 0151, 0162,
0165, 0186, 0204,
0211, 0244, 0245,
0246, 0254
PATHE CINEMA
0200, 0203, 0207,
0212, 0215
PATHE MARCONI
0212, 0216
PAUSA
0208
PERDIO
0200
PHILCO
0060, 0061, 0063,
0128, 0205, 0214,
0215
PHILHARMONIC
0207
PHILIPS
0040, 0060, 0063,
0072, 0115, 0116,
0124, 0130, 0150,
0175, 0184, 0187,
0205, 0207, 0213,
0215, 0217, 0220,
0221, 0232, 0233,
0252, 0253
PHILIPS MAGNAVOX
0124
PHOENIX
0200, 0205, 0213,
0217
PHONOLA
0200, 0205, 0213,
0217
PILOT
0060
PIONEER
0012, 0013, 0060,
0061, 0098, 0109,
0117, 0128, 0181,
0182, 0194, 0195,
0211, 0213, 0216,
0217, 0250
PLANTRON 0206, 0213
POLAROID
0075
POPPY
0208
PORTLAND 0060, 0061
PRANDONI-PRINCE
0204, 0210
PRECISION
0207
PRIMA
0208, 0211
PROFEX
0208
PROFI-TRONIC
0213
PROLINE
0213
PROSCAN
0057
PROSONIC
0200, 0207, 0217
PROTECH
0206, 0207, 0208,
0213, 0214, 0215,
0217
PROTON
0060, 0061
PROVIEW
0050
PROVISION 0217
PULSAR
0060
PYE
0213, 0217
PYMI
0208
QUASAR
0152, 0214
QUELLE
0201, 0206, 0207,
0213, 0214, 0215,
0217
RADIALVA
0218
RADIO SHACK
0064
RADIO SHACK/REALISTIC
0057, 0060, 0061,
0062, 0064
RADIOLA
0213, 0217
RADIOMARELLI
0204, 0205, 0214
RADIOTONE 0213
RCA
0057, 0060, 0061,
0091, 0133, 0135,
0147, 0149
REALISTIC
0064
REVOX
0213, 0217
REX
0206, 0210, 0211
RFT
0203, 0205
RHAPSODY 0200
R-LINE
0213, 0217
ROADSTAR
0206, 0208, 0209,
0218, 0237
ROBOTRON 0205
ROWA
0200
RTF
0205
SABA
0204, 0205, 0211,
0216
SACCS
0212
SAISHO
0204, 0206, 0207,
0208
SALORA
0201, 0204, 0210,
0211, 0215
SAMBERS
0204
SAMPO
0060, 0061, 0083,
0101
SAMSUNG
0029, 0030, 0031,
0032, 0044, 0045,
0046, 0047, 0060,
0061, 0065, 0068,
0069, 0071, 0079,
0087, 0127, 0128,
0130, 0144, 0160,
0161, 0170, 0176,
0183, 0185, 0200,
0201, 0206, 0207,
0208, 0213, 0217,
0239, 0241, 0242,
0243
SANDRA
0200, 0207
SANSUI
0123, 0126, 0213
SANYO
0020, 0021, 0022,
0049, 0060, 0064,
0127, 0128, 0200,
0203, 0207, 0215
SBR
0217
SCHAUB LORENTZ
0211
SCHNEIDER 0207, 0209, 0213,
0215, 0216, 0217,
0218
SCOTCH
0061
SCOTT
0060, 0061, 0062
iv
APPENDIX
0201, 0204, 0207,
0208, 0209, 0213,
0217, 0218
INNOVATION 0206, 0208
INTERBUY
0208, 0214
INTERFUNK 0205, 0211, 0213,
0214, 0216, 0217
INTERNATIONAL
0200
INTERVISION 0206, 0207, 0218
IRRADIO
0201, 0208, 0209,
0213, 0217, 0218
ISUKAI
0209, 0218
ITC
0207, 0215
ITS
0200, 0209, 0213,
0218
ITT
0129, 0208, 0211
ITV
0208, 0217
JBL
0063
JC PENNEY 0057, 0060, 0061
JCB
0059
JENSEN
0060, 0061
JVC
0017, 0018, 0019,
0108, 0136, 0153,
0178, 0190, 0213,
0218
KAISUI
0200, 0207, 0208,
0209, 0218
KAMOSONIC 0207
KAMP
0200, 0207
KAPSCH
0211
KARCHER
0207, 0208, 0212,
0217
KAWASHO
0059, 0060, 0061,
0200
KENDO
0128, 0210
KENNEDY
0215
KENWOOD
0060, 0061
KINGSLEY
0200, 0207
KLOSS NOVABEAM
0062
KNEISSEL
0203
KOLSTER
0213
KONKA
0209, 0218
KORPEL
0213, 0217
KORTING
0205
KOYODA
0208
KTV
0062, 0127, 0207
KYOTO
0200, 0212
LENCO
0208
LENOIR
0207, 0208
LESA
0214
LEYCO
0206, 0213, 0217
LG
0016, 0038, 0039,
0127, 0128, 0157,
0158, 0163, 0164,
0166, 0188, 0189,
0200, 0201, 0207,
0208, 0210, 0213,
0214, 0215, 0217
LIESENK
0217
LIFE
0206, 0208
LIFETEC
0206, 0208, 0218
LOEWE
0063, 0128, 0203,
0204, 0223, 0227
LOEWE OPTA 0205, 0213, 0217
LOGIK
0058
LUMA
0210, 0217
LUMATRON 0210, 0213, 0217
LUX MAY
0213
LUXMAN
0060, 0061
LUXOR
0201, 0207, 0210
LXI
0057, 0061, 0063,
0064
MAG
0050
SEARS
0057, 0060, 0061,
0064
SEG
0200, 0206, 0207,
0214, 0215, 0217
SEI
0204
SEI-SINUDYNE
0204, 0205, 0211
SELECO
0210, 0211, 0215
SENCORA
0208
SENTRA
0218
SERINO
0200
SHARP
0009, 0010, 0011,
0060, 0061, 0066,
0070, 0087, 0111,
0143, 0145, 0167,
0168, 0169, 0198,
0204, 0224, 0247,
0248, 0249
SHOGUN
0060
SIAREM
0204, 0205, 0215
SICATEL
0212
SIEMENS
0255
SIERRA
0213
SIGNATURE 0058
SILVA
0200
SINGER
0205, 0214, 0215
SINUDYNE
0204, 0205, 0215,
0217
SKANTIC
0211
SOLAVOX
0211
SONOKO
0206, 0207, 0208,
0213, 0217
SONOLOR
0211
SONTEC
0213, 0217
SONY
0041, 0059, 0067,
0085, 0086, 0174,
0196, 0199, 0208,
0219, 0234
SOUND & VISION
0209, 0218
SOUNDESIGN 0060, 0061, 0062
SOUNDWAVE 0213, 0217
SSS
0060, 0062
STANDARD 0207, 0208, 0209,
0213, 0218
STARLIGHT 0217
STARLITE
0062
STENWAY
0218
STERN
0210, 0211
SUNKAI
0208, 0218
SUNWOOD
0208, 0213
SUPERLA
0200, 0204, 0207
SUPERTECH 0200
SUPRA
0208
SUPREME
0059
SUSUMU
0209
SUTRON
0208
SYDNEY
0200, 0207
SYLVANIA
0060, 0061, 0063,
0080, 0134, 0142,
0148
SYMPHONIC 0062, 0080
SYSLINE
0217
SYTONG
0200
TANDY
0127, 0207, 0209,
0211, 0218
TASHIKO
0200, 0207, 0210
TATUNG
0127, 0204, 0207,
0213, 0217, 0237
TCM
0206, 0208
TEAC
0127
TEC
0207, 0208, 0214,
0215
TECHWOOD 0060, 0061
v
TEKNIKA
TELEAVIA
TELECOR
TELEFUNKEN
0058, 0060, 0061,
0062
0216
0218
0065, 0213, 0216
TELEGAZI
0218
TELETECH
0208, 0214, 0217
TELETON
0207
TELEVIDEON 0200
TENSAI
0208, 0209, 0213,
0218
TESMET
0213
TEVION
0206, 0208
TEXET
0200, 0207
THOMSON
0191, 0192, 0207,
0213, 0216, 0226
THORN
0212, 0217
TMK
0060, 0061
TOKAI
0213
TOKYO
0200, 0207
TOSHIBA
0027, 0043, 0053,
0054, 0064, 0078,
0089, 0090, 0106,
0107, 0127, 0131,
0140, 0146, 0159,
0197, 0225, 0231,
0237
TOWADA
0211, 0215
TRANSTEC
0200
TRIDENT
0204
TRISTAR
0218
TRIUMPH
0204
UHER
0211, 0213
ULTRAVOX
0200, 0205, 0207,
0214, 0215
UNITED
0217
UNIVERSUM 0127, 0128, 0129,
0201, 0206, 0213,
0214, 0215, 0217
UNIVOX
0212
VESTEL
0210, 0211, 0213,
0214, 0215, 0217
VEXA
0208, 0217
VICTOR
0213
VIDEOLOGIC 0200
VIDEOLOGIQUE
0200, 0207, 0209,
0218
VIDEOSAT
0214
VIDEOSYSTEM
0213
VIDEOTECHNIC
0200
VIDTECH
0060, 0061
VIEWSONIC 0076, 0077, 0092,
0099, 0172, 0173
VISIOLA
0200, 0207
VISION
0213
VORTEC
0213, 0217
VOXSON
0205, 0210, 0211,
0213
WALTHAM
0207, 0212
WARDS
0057, 0058, 0060,
0061, 0063
WATSON
0213, 0217, 0218
WATT RADIO 0200, 0207, 0212,
0215
WEGA
0205
WELTBLICK 0213, 0217
WESTON
0215
WHITE WESTINGHOUSE
0008, 0200, 0207,
0217
WINCOM
0055, 0056
YAMAHA
YAMISHI
YOKO
YORX
ZANUSSI
ZENITH
0000, 0001, 0002,
0003, 0005, 0060,
0061
0218
0200, 0206, 0207,
0208, 0209, 0213,
0217, 0218
0209, 0218
0210
0058, 0060, 0100,
0105, 0119, 0121,
0154
TV/DVD COMBO
AIWA
APEX
BROKSONIC
BUSH
JVC
PANASONIC
RCA
SYLVANIA
THOMSON
TOSHIBA
0139, 2055
0132, 2049
0138, 2060
0230, 2112
0136, 2053
0137, 2054, 0254,
2110
0133, 0135, 2050,
2051
0134, 2052
0226, 2109
0131, 2048, 0231,
2111
TV/DVD/VCR COMBO
PANASONIC
SAMSUNG
SHARP
SYLVANIA
TOSHIBA
0141, 1040, 2057
0241, 1070, 2113
0143, 1028, 2059
0142, 1041, 2058
0140, 1029, 2056
TV/VCR COMBO
AIWA
BUSH
DAEWOO
0237, 1066
0237, 1066
0155, 0238, 1038,
1067
GE
0147, 1030
GOODMANS 0240, 1069
GRUNDIG
0236, 1062
HITACHI
0156, 1039
JVC
0153, 1036
MAGNAVOX 0150, 1033
ORION
0235, 1065
PANASONIC 0151, 1034
PHILIPS
0150, 0232, 0233,
1033, 1062, 1063
QUASAR
0152, 1035
RCA
0149, 1032
ROADSTAR
0237, 1066
SAMSUNG
0144, 0239, 1027,
1068
SHARP
0145, 1028
SONY
0234, 1064
SYLVANIA
0148, 1031
TATUNG
0237, 1066
TOSHIBA
0146, 0237, 1029,
1066
ZENITH
0154, 1037
DVD/VCR COMBO
JVC
LG
PANASONIC
PHILIPS
RCA
1017, 1017, 2045,
2045
1071, 2087
1020, 1072, 2040,
2105
1025, 2046
1022, 2042
SAMSUNG
SHARP
SONY
TOSHIBA
ZENITH
1021, 1021, 2041,
2104
1023, 1073, 2043,
2106
1019, 1074, 2039,
2107
1024, 1075, 2044,
2108
1026, 2047
VCR
ADMIRAL
1008, 1013
ADVENTURA
1005
AIWA
1005, 1042, 1043,
1044, 1066
AKAI
1007, 1043
AKIBA
1050
AKURA
1043, 1050
ALBA
1044, 1050
AMERICAN HIGH
1004
AMSTRAD
1042
ANITECH
1050
ASA
1045, 1046
ASHA
1002, 1014
ASUKA
1042, 1045, 1046,
1050
AUDIO DYNAMICS
1000
AUDIOVOX
1003
BAIRD
1042, 1043, 1047
BASIC LINE 1044, 1050
BAUR
1046
BEAUMARK 1002, 1014
BELL & HOWELL
1001
BLAUPUNKT 1046, 1048
BROKSONIC 1012, 1013
BUSH
1044, 1050, 1066
CALIX
1003
CANDLE
1002, 1003
CANON
1004
CCE
1006
CGE
1042, 1043
CIMLINE
1044, 1050
CITIZEN
1002, 1003
COLORTYME 1000
COLT
1006
CRAIG
1002, 1003, 1006,
1014
CROWN
1050
CURTIS MATHES
1000, 1002, 1004,
1009
CYBERNEX 1002, 1014
DAEWOO
1005, 1038, 1061,
1067
DANSAI
1050
DANTAX
1044
DBX
1000
DE GRAAF
1046, 1049
DECCA
1042, 1043, 1046
DENON
1010
DIMENSIA
1009
DUAL
1043, 1046
DUMONT
1042, 1046, 1047,
1049
DYNATECH 1005
ELECTROHOME
1003
ELECTROPHONIC
1003
ELTA
1050
EMERSON
KENWOOD
1000, 1001, 1007,
1011, 1043
KLH
1006
KODAK
1003, 1004
KORPEL
1050
LEYCO
1050
LG
1003, 1042, 1045,
1071
LIFETEC
1044, 1048
LLOYD'S
1005
LOEWE
1048
LOEWE OPTA 1045, 1046
LOGIK
1006, 1050
LUXOR
1047
LXI
1003
M ELECTRONIC
1042
MAGNASONIC
1047
MAGNAVOX 1004, 1018, 1033
MAGNIN
1003, 1014
MANESTH
1050
MARANTZ
1000, 1001, 1004,
1046, 1051
MARTA
1003
MATSUI
1044, 1045
MATSUSHITA 1004
MEDIATOR
1046
MEDION
1044, 1048
MEI
1004
MEMOREX
1001, 1002, 1003,
1004, 1005, 1008,
1013, 1014, 1042,
1045, 1047
MEMPHIS
1050
METZ
1048
MGA
1014
MGN TECHNOLOGY
1002, 1014
MICROMAXX 1044, 1048
MICROSTAR 1044, 1048
MIGROS
1042
MINOLTA
1010
MITSUBISHI 1011, 1042, 1046
MONTGOMERY WARD
1008
MOTOROLA 1004, 1008
MTC
1002, 1014
MULTITECH 1002, 1005, 1006,
1042, 1046, 1050
MURPHY
1042
NATIONAL
1048
NEC
1000, 1001, 1007,
1011, 1043, 1051
NECKERMANN
1043, 1046
NEI
1046
NESCO
1050
NIKKO
1003
NOBLEX
1002, 1014
NOKIA
1043, 1047
NORDMENDE
1043
OCEANIC
1042, 1043
OKANO
1044
OLYMPUS
1004
OPTIMUS
1003, 1008
ORION
1012, 1013, 1044,
1065
ORSON
1042
OSAKI
1042, 1045, 1050
OTTO VERSAND
1046
PALLADIUM 1043, 1045, 1050
PANASONIC
1004, 1020, 1034,
1040, 1048, 1054,
1072
PATHE MARCONI
1043
PENNEY
1010, 1014
PENTAX
1010, 1049
PERDIO
1042
PHILCO
1004, 1051
PHILIPS
1004, 1025, 1033,
1046, 1056, 1057,
1059, 1062, 1063
PHILIPS MAGNAVOX
1018
PHONOLA
1046
PILOT
1003
PIONEER
1011, 1046
PRINZ
1042
PROFEX
1050
PROFITRONIC
1014
PROLINE
1042
PROSCAN
1009
PROSONIC
1044
PROTEC
1006
PYE
1046, 1056
QUARTER
1001
QUARTZ
1001, 1047
QUASAR
1004, 1035
QUELLE
1042, 1046, 1047
RADIO SHACK
1003
RADIO SHACK/REALISTIC
1001, 1002, 1003,
1004, 1005, 1008
RADIOLA
1046
RADIX
1003
RANDEX
1003
RCA
1002, 1004, 1009,
1010, 1014, 1015,
1022, 1032
REALISTIC
1001, 1002, 1003,
1004, 1005, 1008
REX
1043
RFT
1046
ROADSTAR
1045, 1050, 1066
SABA
1043
SAISHO
1044, 1050
SALORA
1047
SAMSUNG
1002, 1014, 1021,
1027, 1052, 1068,
1070
SANKY
1008
SANSUI
1007, 1011, 1013,
1043
SANYO
1001, 1002, 1014,
1047
SBR
1046
SCHAUB LORENZ
1042, 1043, 1047
SCHNEIDER 1042, 1044, 1045,
1046, 1050
SCOTT
1012
SEARS
1001, 1003, 1004,
1010
SEG
1050
SEI-SINUDYNE
1046
SELECO
1043
SENTRON
1050
SHARP
1008, 1023, 1028,
1053, 1073
SHINTOM
1006, 1047, 1050
SHIVAKI
1045
SHOGUN
1002, 1014
SIEMENS
1045, 1047
SIGNATURE 2000
1008
SILVA
1045
SINGER
1004, 1006
SINUDYNE
1046
SONTEC
1045
SONY
1016, 1019, 1055,
1060, 1064, 1074
STS
1004, 1010
SUNKAI
1044
SUNSTAR
1042
SUNTRONIC 1042
SUNWOOD
1050
SYLVANIA
1004, 1005, 1031,
1041
SYMPHONIC 1005
TAISHO
1044
TANDY
1001
TASHIKO
1003, 1042
TATUNG
1007, 1042, 1043,
1046, 1066
TCM
1044, 1048
TEAC
1005, 1007
TECHNICS
1004, 1048
TEKNIKA
1003, 1004, 1005
TELEAVIA
1043
TELEFUNKEN
1043
TENOSAL
1050
TENSAI
1042, 1045, 1050
TEVION
1044, 1048
THOMSON
1043, 1058
THORN
1043, 1047
TMK
1002, 1014
TOKAI
1045, 1050
TONSAI
1050
TOSHIBA
1013, 1024, 1029,
1043, 1046, 1066,
1075
TOTEVISION 1002, 1003, 1014
TOWADA
1050
TOWIKA
1050
UHER
1045
UNITECH
1002, 1014
UNIVERSUM 1042, 1045, 1046
VECTOR RESEARCH
1000
VIDEO CONCEPTS
1000
VIDEON
1044, 1048
VIDEOSONIC 1002, 1014
WARDS
1002, 1003, 1004,
1005, 1006, 1008,
1010, 1014
WELTBLICK 1045
WHITE WESTINGHOUSE
1013
XR-1000
1004, 1005, 1006
YAMAHA
1000, 1001, 1007
YAMISHI
1050
YOKAN
1050
YOKO
1045, 1050
ZENITH
1013, 1026, 1037
DVD
ACOUSTIC SOLUTIONS
2078
AIWA
2055, 2100
AKAI
2096
AKURA
2076
ALBA
2078, 2086
APEX
2027, 2049
AWA
2078
vi
APPENDIX
1003, 1004, 1005,
1012, 1013
ETZUKO
1050
FERGUSON 1043
FIDELITY
1042
FINLANDIA 1046, 1047, 1049
FINLUX
1042, 1043, 1046,
1047, 1049
FIRST LINE 1044, 1045, 1049,
1050
FISHER
1001, 1047
FLINT
1044
FORMENTI/PHOENIX
1046
FUJI
1004
FUJITSU
1042
FUNAI
1005, 1042
GALAXY
1042
GARRARD
1005
GBC
1050
GE
1002, 1004, 1009,
1014, 1030
GEC
1046
GELOSO
1050
GENERAL TECHNIC
1044, 1048
GO VIDEO
1014
GOLDHAND 1050
GOLDSTAR
1000, 1003, 1042,
1045
GOODMANS 1042, 1045, 1050,
1069
GRADIENTE 1005
GRAETZ
1043, 1047
GRANADA
1046, 1047, 1049
GRANDIN
1042, 1045, 1050
GRUNDIG
1046, 1050, 1062
HANSEATIC 1045, 1046
HARLEY DAVIDSON
1005
HARMAN/KARDON
1000
HARWOOD
1006
HCM
1050
HEADQUARTER
1001
HINARI
1044, 1050
HISAWA
1044
HITACHI
1007, 1010, 1039,
1042, 1043, 1046,
1049
HUGHES NETWORK SYSTEMS
1010
HYPSON
1044, 1050
IMPERIAL
1042
INNO HIT
1046, 1050
INNOVATION 1044, 1048
INSTANT REPLAY
1004
INTERBUY
1045
INTERFUNK 1046, 1047
INTERVISION 1042
IRRADIO
1045, 1050
ITT
1043, 1047
ITV
1045
JC PENNEY 1000, 1001, 1002,
1003, 1004, 1006
JCL
1004
JENSEN
1007
JVC
1000, 1001, 1007,
1011, 1017, 1036,
1043
KAISUI
1050
KARCHER
1046
KENDO
1044
01EN_HTR-6030_U_cv-4.fm Page vii Tuesday, December 19, 2006 11:14 AM
AXION
BRAINWAVE
BRANDT
BROKSONIC
BUSH
CENTREX
CLASSIC
CLATRONIC
COBY
C-TECH
CYBERHOME
2078
2096
2073, 2085
2060
2075, 2078, 2112
2077
2078
2075
2078
2074
2025, 2079, 2091
DAEWOO
2092, 2098
DANSAI
2096
DAYTEK
2080, 2089
DEC
2075
DENON
2030, 2102, 2103
DENVER
2075, 2076
DIAMOND
2074
DK DIGITAL 2094
DUAL
2078
D-VISION
2096
DVX
2074
ELTA
2096
EUROLINE
2096
FUNAI
2052, 2058
GLOBAL SOLUTIONS
2074
GLOBAL SPHERE
2074
GOODMANS 2075, 2077, 2078
GRUNDIG
2077, 2098
H&B
2075
HAAZ
2074
HE
2078
HITACHI
2032, 2072
HOME ELECTRONICS
2078
INNOVATION 2072
IRRADIO
2134
JDB
2078
JVC
2033, 2045, 2053,
2073, 2099
KENWOOD
2030, 2097
KINGAVON
2075
KODA
2075
LAWSON
2074
LENCO
2075
LG
2084, 2087
LIFETEC
2072
LIMIT
2074
LOGICLAB
2074
LUXOR
2077
MAGNAVOX 2037, 2073, 2075
MAGNUM
2072
MBO
2078
MEDION
2072
MICROMAXX
2072
MICROMEDIA
2073
MICROSTAR 2072
MITSUBISHI 2035
MIZUDA
2075
MUSTEK
2078
NAIKO
2077
ONKYO
2073, 2135
ORAVA
P&B
PACIFIC
PANASONIC
2075
2075
2074
2030, 2040, 2054,
2057, 2105, 2110
PHILIPS
2019, 2026, 2046,
2073, 2081, 2090
PIONEER
2036, 2082
PROLINE
2077
PROVISION 2075
RCA
2031, 2042, 2050,
2051
RED STAR
2076
REOC
2074
ROADSTAR
2075, 2078, 2086
ROWA
2077
SABA
2085
SABAKI
2074
SAMSUNG
2032, 2041, 2104,
2113
SANSUI
2074
SANYO
2095
SCANMAGIC 2078
SCIENTIFIC LABS
2074
SCOTT
2088
SEG
2074, 2086
SHARP
2034, 2043, 2059,
2093, 2106
SILVA
2076
SINGER
2074
SKYMASTER 2074, 2078
SKYWORTH 2076
SM ELECTRONIC
2074, 2078
SONY
2028, 2029, 2039,
2083, 2107
SOUNDMASTER
2074
SOUNDMAX 2074
STANDARD 2074
STAR CLUSTER
2074
STARMEDIA 2075
SUPERVISION
2074, 2078
SYLVANIA
2052, 2058
SYNN
2074
TCM
2072
TEAC
2074
TEC
2076
TECHNICS
2030
TECHNIKA
2096
TECHNOSONIC
2096
TEVION
2072, 2074
THOMSON
2085, 2109
TOKAI
2076
TOSHIBA
2026, 2044, 2048,
2056, 2073, 2108,
2111
UNITED
2078
VOXSON
2078
WHARFEDALE
2074
XLOGIC
2074
YAKUMO
2077
YAMADA
YAMAHA
YUKAI
ZENITH
2077
2000, 2001, 2003,
2030, 2101
2078
2038, 2047, 2073
DVD-DVR
PANASONIC
PIONEER
SAMSUNG
TOSHIBA
2067
2114
2115
2068
DVD/LD COMBO
PIONEER
2036
DVD RECORDER
APEX
JVC
LG
PANASONIC
PHILIPS
PIONEER
RCA
SONY
TOSHIBA
YAMAHA
YUKAI
2024
2070
2071
2020, 2065, 2066,
2067
2019, 2061, 2062,
2063
2021
2018
2022, 2064
2068
2023
2069
NIVEUS MEDIA
2132
NORTHGATE 2132
PANASONIC 2015, 2016, 2017,
2120
PHILIPS
2117, 2121, 2123,
2128
PIONEER
2012, 2013, 2014
PROSCAN
2129
RCA
2116, 2124, 2129,
2133
REPLAYTV
2118, 2119, 2120
SHARP
2009, 2010
SONIC BLUE 2119, 2120
SONY
2005, 2006, 2007,
2122, 2130, 2131,
2132
STACK 9
2132
SYSTEMAX 2132
TAGAR SYSTEMS
2132
TIVO
2116, 2121, 2122,
2123, 2130, 2131
TOSHIBA
2004, 2125, 2132
TOUCH
2132
ULTIMATETV 2133
VIEWSONIC 2132
VOODOO
2132
YAMAHA
2011
ZT GROUP
2132
LD PLAYER
YAMAHA
2002
DVR
ABS
2132
ALIENWARE 2132
CYBERPOWER
2132
DELL
2132
DIRECTV
2123, 2128, 2129,
2133
DISH NETWORK
2126, 2127
DISHPRO
2126
ECHOSTAR
2126, 2127
EXPRESSVU 2126
GATEWAY
2132
GOI
2126
HEWLETT PACKARD
2132
HITACHI
2008
HOWARD COMPUTERS
2132
HTS
2126
HUGHES
2123, 2128
HUMAX
2123
HUSH
2132
IBUYPOWER 2132
JVC
2126, 2127
LINKSYS
2132
MEDIA CENTER PC
2132
MICROSOFT 2132
MIND
2132
© 2007
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
CD PLAYER
YAMAHA
5000, 5013
CD RECORDER
YAMAHA
5001
MD
YAMAHA
5002, 5003, 5004
TAPE DECK
YAMAHA
5005, 5006
TUNER
YAMAHA
5007, 5008, 5009,
5010, 5012, 5014
OTHER AUDIO
ACCESSORIES
YAMAHA
(iPod)
5011
All rights reserved.
Printed in China
WJ63840
00_Sheet_HTR-6030_U.book Page 1 Thursday, December 28, 2006 10:19 AM
U
HTR-6030
The circled numbers and alphabets correspond to those in the Owner’s Manual.
■ Front panel
1
2
3
4
5
6
7
8
VOLUME
STANDBY
/ON
EDIT
SEARCH MODE
PRESET/TUNING
CATEGORY
A/B/C/D/E
FM/AM
l
PRESET/TUNING/CH
h
MEMORY
DISPLAY
TUNING AUTO/MAN'L
SCENE
1
l
PHONES
SPEAKERS
A/B/OFF
PROGRAM
TONE CONTROL
2
3
STRAIGHT
NIGHT
h
4
l
INPUT
VIDEO AUX
h
AUDIO SELECT
EFFECT
SILENT CINEMA
9
0
A
B C
D
E F
VIDEO
L
AUDIO
R
PORTABLE
00_Sheet_HTR-6030_U.book Page i Thursday, December 28, 2006 10:19 AM
■ Remote control
X
A
B
C
POWER
POWER
TV
AV
MULTI CH IN
STANDBY
POWER
AUDIO SEL
SLEEP
MUTE
CD
MD/CD-R
TUNER
DVD
DTV/CBL
DVR
TV CH
V-AUX
XM
AMP
TV INPUT
TV MUTE
TV VOL
L
M
N
O
D
E
F
SCENE
1
BAND LEVEL
TITLE
G
H
2
3
4
SRCH MODE
VOLUME
MENU
Q
ENTER
RETURN
XM MEMORY
P
R
DISPLAY
REC
I
J
K
l
PROG h
1
2
ENHANCER STRAIGHT
3
4
8
SUR.DECODE NIGHT
5
6
7
9
0
10
ENT.
S
T
U
V
W
Printed in China
WK14310