M1001 Specifications Sheet

MODEL M1001
SHOP FOX ® 6" X 26" VERTICAL MILL
Product Dimensions
Weight.......................................................................................................... 900 lbs.
Width (side-to-side) x Depth (front-to-back) x Height.............................. 45-1/2 x 41 x 66-5/8 in.
Footprint (Length x Width)......................................................................... 27-1/2 x 21 in.
Shipping Dimensions
Type....................................................................................................... Wood Crate
Content........................................................................................................ Machine
Weight.......................................................................................................... 936 lbs.
Length x Width x Height........................................................................... 37 x 41 x 75 in.
Electrical
Power Requirement.......................................................... 110V or 220V, Single-Phase, 60 Hz
Prewired Voltage................................................................................................. 110V
Full-Load Current Rating................................................................ 16A at 110V, 8A at 220V
Minimum Circuit Size................................................................... 20A at 110V, 15A at 220V
Connection Type......................................................................................... Cord & Plug
Power Cord Included.............................................................................................. Yes
Power Cord Length............................................................................................... 6 ft.
Power Cord Gauge............................................................................................ 14 AWG
Plug Included....................................................................................................... Yes
Included Plug Type.................................................................................... 5-15 for 110V
Recommended Plug Type............................................................................. 6-15 for 220V
Switch Type.......................................................................................... ON/OFF Switch
Motors
Main
Type......................................................................... TEFC Capacitor-Start Induction
Horsepower.............................................................................................. 1.5 HP
Phase.............................................................................................. Single-Phase
Amps..................................................................................................... 16A/8A
Speed.................................................................................................. 1725 RPM
Power Transfer ................................................................................... V-Belt Drive
Bearings............................................................... Shielded & Permanently Lubricated
Model M1001 Machine Specifications, Page 1 of 3
Main Specifications
Operation Info
Spindle Travel.............................................................................................. 3 in.
Max Distance Spindle to Column................................................................... 5-1/2 in.
Max Distance Spindle to Table.................................................................... 11-7/8 in.
Longitudinal Table Travel (X-Axis)............................................................... 14-1/4 in.
Cross Table Travel (Y-Axis).............................................................................. 6 in.
Vertical Table Travel (Z-Axis).......................................................................... 14 in.
Vertical Head Travel (Z-Axis)....................................................................... 2-1/2 in.
Ram Travel................................................................................................ 12 in.
Turret or Column Swivel (Left /Right)............................................................ 360 deg.
Head Tilt (Left/Right)................................................................................. 90 deg.
Head Tilt (Front/Back)................................................................................ 45 deg.
Drilling Capacity for Cast Iron........................................................................... 1 in.
Drilling Capacity for Steel............................................................................. 3/4 in.
End Milling Capacity.................................................................................... 3/4 in.
Face Milling Capacity..................................................................................... 3 in.
Table Info
Table Length.............................................................................................. 26 in.
Table Width........................................................................................... 6-1/8 in.
Table Thickness....................................................................................... 1-3/4 in.
Number of T-Slots............................................................................................. 3
T-Slot Size.............................................................................................. 0.56 in.
T-Slots Centers...................................................................................... 1-9/16 in.
Number of Longitudinal Feeds...................................................................... Variable
X-Axis Table Power Feed Rate................................................................ 0 – 11.67 FPM
X/Y-Axis Travel per Handwheel Revolution...................................................... 0.125 in.
Z-Axis Travel per Handwheel Revolution......................................................... 0.062 in.
Spindle Info
Spindle Taper................................................................................................ R-8
Number of Vertical Spindle Speeds......................................................................... 9
Range of Vertical Spindle Speeds.......................................................... 240 – 2760 RPM
Quill Diameter........................................................................................ 2.950 in.
Drawbar Thread Size.................................................................................. 7/16-20
Drawbar Length..................................................................................... 12-1/4 in.
Spindle Bearings.................................................................... Tapered Roller Bearings
Construction
Spindle Housing/Quill................................................................................ Cast Iron
Table............................................................................... Surface-Ground Cast Iron
Head.................................................................................................... Cast Iron
Column/Base.......................................................................................... Cast Iron
Base.................................................................................................... Cast Iron
Stand........................................................................................................ Steel
Paint Type/Finish...................................................................................... Enamel
Other
Recommended Mobile Base........................................................................... D2058A
Model M1001 Machine Specifications, Page 2 of 3
Other
Country of Origin ............................................................................................... China
Warranty ....................................................................................................... 2 Years
Approximate Assembly & Setup Time ...................................................................... 1 Hour
ISO 9001 Factory ................................................................................................... No
CSA, ETL, or UL Certified/Listed ................................................................................ No
Features
Milling Head Micro-Feed
Built-In Work Light
Class 7 Spindle Bearings
Head Tilts to 45 Deg. Both Ways.
Single-Shot Lubrication System
High-Precision Ground Vertical and Cross Ways
Accessories
Drawbar
Tool Box
3 In. Shell Mill with Arbor
Hex Wrench Set, 3-6mm
Open End Wrenches
Screwdrivers
Model M1001 Machine Specifications, Page 3 of 3